In the Linux kernel, the following vulnerability has been resolved: tracing: Fix wild-memory-access in register_synth_event() In register_synth_event(), if set_synth_event_print_fmt() failed, then both trace_remove_event_call() and unregister_trace_event() will be called, which means the trace_event_call will call __unregister_trace_event() twice. As the result, the second unregister will causes the wild-memory-access. register_synth_event set_synth_event_print_fmt failed trace_remove_event_call event_remove if call->event.funcs then __unregister_trace_event (first call) unregister_trace_event __unregister_trace_event (second call) Fix the bug by avoiding to call the second __unregister_trace_event() by checking if the first one is called. general protection fault, probably for non-canonical address 0xfbd59c0000000024: 0000 [#1] SMP KASAN PTI KASAN: maybe wild-memory-access in range [0xdead000000000120-0xdead000000000127] CPU: 0 PID: 3807 Comm: modprobe Not tainted 6.1.0-rc1-00186-g76f33a7eedb4 #299 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014 RIP: 0010:unregister_trace_event+0x6e/0x280 Code: 00 fc ff df 4c 89 ea 48 c1 ea 03 80 3c 02 00 0f 85 0e 02 00 00 48 b8 00 00 00 00 00 fc ff df 4c 8b 63 08 4c 89 e2 48 c1 ea 03 <80> 3c 02 00 0f 85 e2 01 00 00 49 89 2c 24 48 85 ed 74 28 e8 7a 9b RSP: 0018:ffff88810413f370 EFLAGS: 00010a06 RAX: dffffc0000000000 RBX: ffff888105d050b0 RCX: 0000000000000000 RDX: 1bd5a00000000024 RSI: ffff888119e276e0 RDI: ffffffff835a8b20 RBP: dead000000000100 R08: 0000000000000000 R09: fffffbfff0913481 R10: ffffffff8489a407 R11: fffffbfff0913480 R12: dead000000000122 R13: ffff888105d050b8 R14: 0000000000000000 R15: ffff888105d05028 FS: 00007f7823e8d540(0000) GS:ffff888119e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7823e7ebec CR3: 000000010a058002 CR4: 0000000000330ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __create_synth_event+0x1e37/0x1eb0 create_or_delete_synth_event+0x110/0x250 synth_event_run_command+0x2f/0x110 test_gen_synth_cmd+0x170/0x2eb [synth_event_gen_test] synth_event_gen_test_init+0x76/0x9bc [synth_event_gen_test] do_one_initcall+0xdb/0x480 do_init_module+0x1cf/0x680 load_module+0x6a50/0x70a0 __do_sys_finit_module+0x12f/0x1c0 do_syscall_64+0x3f/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd

In the Linux kernel, the following vulnerability has been resolved: powerpc/xive/spapr: correct bitmap allocation size kasan detects access beyond the end of the xibm->bitmap allocation: BUG: KASAN: slab-out-of-bounds in _find_first_zero_bit+0x40/0x140 Read of size 8 at addr c00000001d1d0118 by task swapper/0/1 CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.19.0-rc2-00001-g90df023b36dd #28 Call Trace: [c00000001d98f770] [c0000000012baab8] dump_stack_lvl+0xac/0x108 (unreliable) [c00000001d98f7b0] [c00000000068faac] print_report+0x37c/0x710 [c00000001d98f880] [c0000000006902c0] kasan_report+0x110/0x354 [c00000001d98f950] [c000000000692324] __asan_load8+0xa4/0xe0 [c00000001d98f970] [c0000000011c6ed0] _find_first_zero_bit+0x40/0x140 [c00000001d98f9b0] [c0000000000dbfbc] xive_spapr_get_ipi+0xcc/0x260 [c00000001d98fa70] [c0000000000d6d28] xive_setup_cpu_ipi+0x1e8/0x450 [c00000001d98fb30] [c000000004032a20] pSeries_smp_probe+0x5c/0x118 [c00000001d98fb60] [c000000004018b44] smp_prepare_cpus+0x944/0x9ac [c00000001d98fc90] [c000000004009f9c] kernel_init_freeable+0x2d4/0x640 [c00000001d98fd90] [c0000000000131e8] kernel_init+0x28/0x1d0 [c00000001d98fe10] [c00000000000cd54] ret_from_kernel_thread+0x5c/0x64 Allocated by task 0: kasan_save_stack+0x34/0x70 __kasan_kmalloc+0xb4/0xf0 __kmalloc+0x268/0x540 xive_spapr_init+0x4d0/0x77c pseries_init_irq+0x40/0x27c init_IRQ+0x44/0x84 start_kernel+0x2a4/0x538 start_here_common+0x1c/0x20 The buggy address belongs to the object at c00000001d1d0118 which belongs to the cache kmalloc-8 of size 8 The buggy address is located 0 bytes inside of 8-byte region [c00000001d1d0118, c00000001d1d0120) The buggy address belongs to the physical page: page:c00c000000074740 refcount:1 mapcount:0 mapping:0000000000000000 index:0xc00000001d1d0558 pfn:0x1d1d flags: 0x7ffff000000200(slab|node=0|zone=0|lastcpupid=0x7ffff) raw: 007ffff000000200 c00000001d0003c8 c00000001d0003c8 c00000001d010480 raw: c00000001d1d0558 0000000001e1000a 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: c00000001d1d0000: fc 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc c00000001d1d0080: fc fc 00 fc fc fc fc fc fc fc fc fc fc fc fc fc >c00000001d1d0100: fc fc fc 02 fc fc fc fc fc fc fc fc fc fc fc fc ^ c00000001d1d0180: fc fc fc fc 04 fc fc fc fc fc fc fc fc fc fc fc c00000001d1d0200: fc fc fc fc fc 04 fc fc fc fc fc fc fc fc fc fc This happens because the allocation uses the wrong unit (bits) when it should pass (BITS_TO_LONGS(count) * sizeof(long)) or equivalent. With small numbers of bits, the allocated object can be smaller than sizeof(long), which results in invalid accesses. Use bitmap_zalloc() to allocate and initialize the irq bitmap, paired with bitmap_free() for consistency.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to do sanity check on i_extra_isize in is_alive() syzbot found a f2fs bug: BUG: KASAN: slab-out-of-bounds in data_blkaddr fs/f2fs/f2fs.h:2891 [inline] BUG: KASAN: slab-out-of-bounds in is_alive fs/f2fs/gc.c:1117 [inline] BUG: KASAN: slab-out-of-bounds in gc_data_segment fs/f2fs/gc.c:1520 [inline] BUG: KASAN: slab-out-of-bounds in do_garbage_collect+0x386a/0x3df0 fs/f2fs/gc.c:1734 Read of size 4 at addr ffff888076557568 by task kworker/u4:3/52 CPU: 1 PID: 52 Comm: kworker/u4:3 Not tainted 6.1.0-rc4-syzkaller-00362-gfef7fd48922d #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022 Workqueue: writeback wb_workfn (flush-7:0) Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_address_description mm/kasan/report.c:284 [inline] print_report+0x15e/0x45d mm/kasan/report.c:395 kasan_report+0xbb/0x1f0 mm/kasan/report.c:495 data_blkaddr fs/f2fs/f2fs.h:2891 [inline] is_alive fs/f2fs/gc.c:1117 [inline] gc_data_segment fs/f2fs/gc.c:1520 [inline] do_garbage_collect+0x386a/0x3df0 fs/f2fs/gc.c:1734 f2fs_gc+0x88c/0x20a0 fs/f2fs/gc.c:1831 f2fs_balance_fs+0x544/0x6b0 fs/f2fs/segment.c:410 f2fs_write_inode+0x57e/0xe20 fs/f2fs/inode.c:753 write_inode fs/fs-writeback.c:1440 [inline] __writeback_single_inode+0xcfc/0x1440 fs/fs-writeback.c:1652 writeback_sb_inodes+0x54d/0xf90 fs/fs-writeback.c:1870 wb_writeback+0x2c5/0xd70 fs/fs-writeback.c:2044 wb_do_writeback fs/fs-writeback.c:2187 [inline] wb_workfn+0x2dc/0x12f0 fs/fs-writeback.c:2227 process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289 worker_thread+0x665/0x1080 kernel/workqueue.c:2436 kthread+0x2e4/0x3a0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306 The root cause is that we forgot to do sanity check on .i_extra_isize in below path, result in accessing invalid address later, fix it. - gc_data_segment - is_alive - data_blkaddr - offset_in_addr

In the Linux kernel, the following vulnerability has been resolved: dm raid: fix address sanitizer warning in raid_status There is this warning when using a kernel with the address sanitizer and running this testsuite: https://gitlab.com/cki-project/kernel-tests/-/tree/main/storage/swraid/scsi_raid ================================================================== BUG: KASAN: slab-out-of-bounds in raid_status+0x1747/0x2820 [dm_raid] Read of size 4 at addr ffff888079d2c7e8 by task lvcreate/13319 CPU: 0 PID: 13319 Comm: lvcreate Not tainted 5.18.0-0.rc3.<snip> #1 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 Call Trace: <TASK> dump_stack_lvl+0x6a/0x9c print_address_description.constprop.0+0x1f/0x1e0 print_report.cold+0x55/0x244 kasan_report+0xc9/0x100 raid_status+0x1747/0x2820 [dm_raid] dm_ima_measure_on_table_load+0x4b8/0xca0 [dm_mod] table_load+0x35c/0x630 [dm_mod] ctl_ioctl+0x411/0x630 [dm_mod] dm_ctl_ioctl+0xa/0x10 [dm_mod] __x64_sys_ioctl+0x12a/0x1a0 do_syscall_64+0x5b/0x80 The warning is caused by reading conf->max_nr_stripes in raid_status. The code in raid_status reads mddev->private, casts it to struct r5conf and reads the entry max_nr_stripes. However, if we have different raid type than 4/5/6, mddev->private doesn't point to struct r5conf; it may point to struct r0conf, struct r1conf, struct r10conf or struct mpconf. If we cast a pointer to one of these structs to struct r5conf, we will be reading invalid memory and KASAN warns about it. Fix this bug by reading struct r5conf only if raid type is 4, 5 or 6.

In the Linux kernel, the following vulnerability has been resolved: can: dev: fix skb drop check In commit a6d190f8c767 ("can: skb: drop tx skb if in listen only mode") the priv->ctrlmode element is read even on virtual CAN interfaces that do not create the struct can_priv at startup. This out-of-bounds read may lead to CAN frame drops for virtual CAN interfaces like vcan and vxcan. This patch mainly reverts the original commit and adds a new helper for CAN interface drivers that provide the required information in struct can_priv. [mkl: patch pch_can, too]

In the Linux kernel, the following vulnerability has been resolved: cpufreq: qcom: fix writes in read-only memory region This commit fixes a kernel oops because of a write in some read-only memory: [ 9.068287] Unable to handle kernel write to read-only memory at virtual address ffff800009240ad8 ..snip.. [ 9.138790] Internal error: Oops: 9600004f [#1] PREEMPT SMP ..snip.. [ 9.269161] Call trace: [ 9.276271] __memcpy+0x5c/0x230 [ 9.278531] snprintf+0x58/0x80 [ 9.282002] qcom_cpufreq_msm8939_name_version+0xb4/0x190 [ 9.284869] qcom_cpufreq_probe+0xc8/0x39c ..snip.. The following line defines a pointer that point to a char buffer stored in read-only memory: char *pvs_name = "speedXX-pvsXX-vXX"; This pointer is meant to hold a template "speedXX-pvsXX-vXX" where the XX values get overridden by the qcom_cpufreq_krait_name_version function. Since the template is actually stored in read-only memory, when the function executes the following call we get an oops: snprintf(*pvs_name, sizeof("speedXX-pvsXX-vXX"), "speed%d-pvs%d-v%d", speed, pvs, pvs_ver); To fix this issue, we instead store the template name onto the stack by using the following syntax: char pvs_name_buffer[] = "speedXX-pvsXX-vXX"; Because the `pvs_name` needs to be able to be assigned to NULL, the template buffer is stored in the pvs_name_buffer and not under the pvs_name variable.

In the Linux kernel, the following vulnerability has been resolved: zonefs: fix zonefs_iomap_begin() for reads If a readahead is issued to a sequential zone file with an offset exactly equal to the current file size, the iomap type is set to IOMAP_UNWRITTEN, which will prevent an IO, but the iomap length is calculated as 0. This causes a WARN_ON() in iomap_iter(): [17309.548939] WARNING: CPU: 3 PID: 2137 at fs/iomap/iter.c:34 iomap_iter+0x9cf/0xe80 [...] [17309.650907] RIP: 0010:iomap_iter+0x9cf/0xe80 [...] [17309.754560] Call Trace: [17309.757078] <TASK> [17309.759240] ? lock_is_held_type+0xd8/0x130 [17309.763531] iomap_readahead+0x1a8/0x870 [17309.767550] ? iomap_read_folio+0x4c0/0x4c0 [17309.771817] ? lockdep_hardirqs_on_prepare+0x400/0x400 [17309.778848] ? lock_release+0x370/0x750 [17309.784462] ? folio_add_lru+0x217/0x3f0 [17309.790220] ? reacquire_held_locks+0x4e0/0x4e0 [17309.796543] read_pages+0x17d/0xb60 [17309.801854] ? folio_add_lru+0x238/0x3f0 [17309.807573] ? readahead_expand+0x5f0/0x5f0 [17309.813554] ? policy_node+0xb5/0x140 [17309.819018] page_cache_ra_unbounded+0x27d/0x450 [17309.825439] filemap_get_pages+0x500/0x1450 [17309.831444] ? filemap_add_folio+0x140/0x140 [17309.837519] ? lock_is_held_type+0xd8/0x130 [17309.843509] filemap_read+0x28c/0x9f0 [17309.848953] ? zonefs_file_read_iter+0x1ea/0x4d0 [zonefs] [17309.856162] ? trace_contention_end+0xd6/0x130 [17309.862416] ? __mutex_lock+0x221/0x1480 [17309.868151] ? zonefs_file_read_iter+0x166/0x4d0 [zonefs] [17309.875364] ? filemap_get_pages+0x1450/0x1450 [17309.881647] ? __mutex_unlock_slowpath+0x15e/0x620 [17309.888248] ? wait_for_completion_io_timeout+0x20/0x20 [17309.895231] ? lock_is_held_type+0xd8/0x130 [17309.901115] ? lock_is_held_type+0xd8/0x130 [17309.906934] zonefs_file_read_iter+0x356/0x4d0 [zonefs] [17309.913750] new_sync_read+0x2d8/0x520 [17309.919035] ? __x64_sys_lseek+0x1d0/0x1d0 Furthermore, this causes iomap_readahead() to loop forever as iomap_readahead_iter() always returns 0, making no progress. Fix this by treating reads after the file size as access to holes, setting the iomap type to IOMAP_HOLE, the iomap addr to IOMAP_NULL_ADDR and using the length argument as is for the iomap length. To simplify the code with this change, zonefs_iomap_begin() is split into the read variant, zonefs_read_iomap_begin() and zonefs_read_iomap_ops, and the write variant, zonefs_write_iomap_begin() and zonefs_write_iomap_ops.

In the Linux kernel, the following vulnerability has been resolved: selinux: Add boundary check in put_entry() Just like next_entry(), boundary check is necessary to prevent memory out-of-bound access.

In the Linux kernel, the following vulnerability has been resolved: media: venus: Add a check for packet size after reading from shared memory Add a check to ensure that the packet size does not exceed the number of available words after reading the packet header from shared memory. This ensures that the size provided by the firmware is safe to process and prevent potential out-of-bounds memory access.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (gpio-fan) Fix array out of bounds access The driver does not check if the cooling state passed to gpio_fan_set_cur_state() exceeds the maximum cooling state as stored in fan_data->num_speeds. Since the cooling state is later used as an array index in set_fan_speed(), an array out of bounds access can occur. This can be exploited by setting the state of the thermal cooling device to arbitrary values, causing for example a kernel oops when unavailable memory is accessed this way. Example kernel oops: [ 807.987276] Unable to handle kernel paging request at virtual address ffffff80d0588064 [ 807.987369] Mem abort info: [ 807.987398] ESR = 0x96000005 [ 807.987428] EC = 0x25: DABT (current EL), IL = 32 bits [ 807.987477] SET = 0, FnV = 0 [ 807.987507] EA = 0, S1PTW = 0 [ 807.987536] FSC = 0x05: level 1 translation fault [ 807.987570] Data abort info: [ 807.987763] ISV = 0, ISS = 0x00000005 [ 807.987801] CM = 0, WnR = 0 [ 807.987832] swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000001165000 [ 807.987872] [ffffff80d0588064] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000 [ 807.987961] Internal error: Oops: 96000005 [#1] PREEMPT SMP [ 807.987992] Modules linked in: cmac algif_hash aes_arm64 algif_skcipher af_alg bnep hci_uart btbcm bluetooth ecdh_generic ecc 8021q garp stp llc snd_soc_hdmi_codec brcmfmac vc4 brcmutil cec drm_kms_helper snd_soc_core cfg80211 snd_compress bcm2835_codec(C) snd_pcm_dmaengine syscopyarea bcm2835_isp(C) bcm2835_v4l2(C) sysfillrect v4l2_mem2mem bcm2835_mmal_vchiq(C) raspberrypi_hwmon sysimgblt videobuf2_dma_contig videobuf2_vmalloc fb_sys_fops videobuf2_memops rfkill videobuf2_v4l2 videobuf2_common i2c_bcm2835 snd_bcm2835(C) videodev snd_pcm snd_timer snd mc vc_sm_cma(C) gpio_fan uio_pdrv_genirq uio drm fuse drm_panel_orientation_quirks backlight ip_tables x_tables ipv6 [ 807.988508] CPU: 0 PID: 1321 Comm: bash Tainted: G C 5.15.56-v8+ #1575 [ 807.988548] Hardware name: Raspberry Pi 3 Model B Rev 1.2 (DT) [ 807.988574] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 807.988608] pc : set_fan_speed.part.5+0x34/0x80 [gpio_fan] [ 807.988654] lr : gpio_fan_set_cur_state+0x34/0x50 [gpio_fan] [ 807.988691] sp : ffffffc008cf3bd0 [ 807.988710] x29: ffffffc008cf3bd0 x28: ffffff80019edac0 x27: 0000000000000000 [ 807.988762] x26: 0000000000000000 x25: 0000000000000000 x24: ffffff800747c920 [ 807.988787] x23: 000000000000000a x22: ffffff800369f000 x21: 000000001999997c [ 807.988854] x20: ffffff800369f2e8 x19: ffffff8002ae8080 x18: 0000000000000000 [ 807.988877] x17: 0000000000000000 x16: 0000000000000000 x15: 000000559e271b70 [ 807.988938] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 [ 807.988960] x11: 0000000000000000 x10: ffffffc008cf3c20 x9 : ffffffcfb60c741c [ 807.989018] x8 : 000000000000000a x7 : 00000000ffffffc9 x6 : 0000000000000009 [ 807.989040] x5 : 000000000000002a x4 : 0000000000000000 x3 : ffffff800369f2e8 [ 807.989062] x2 : 000000000000e780 x1 : 0000000000000001 x0 : ffffff80d0588060 [ 807.989084] Call trace: [ 807.989091] set_fan_speed.part.5+0x34/0x80 [gpio_fan] [ 807.989113] gpio_fan_set_cur_state+0x34/0x50 [gpio_fan] [ 807.989199] cur_state_store+0x84/0xd0 [ 807.989221] dev_attr_store+0x20/0x38 [ 807.989262] sysfs_kf_write+0x4c/0x60 [ 807.989282] kernfs_fop_write_iter+0x130/0x1c0 [ 807.989298] new_sync_write+0x10c/0x190 [ 807.989315] vfs_write+0x254/0x378 [ 807.989362] ksys_write+0x70/0xf8 [ 807.989379] __arm64_sys_write+0x24/0x30 [ 807.989424] invoke_syscall+0x4c/0x110 [ 807.989442] el0_svc_common.constprop.3+0xfc/0x120 [ 807.989458] do_el0_svc+0x2c/0x90 [ 807.989473] el0_svc+0x24/0x60 [ 807.989544] el0t_64_sync_handler+0x90/0xb8 [ 807.989558] el0t_64_sync+0x1a0/0x1a4 [ 807.989579] Code: b9403801 f9402800 7100003f 8b35cc00 (b9400416) [ 807.989627] ---[ end t ---truncated---

In the Linux kernel, the following vulnerability has been resolved: capabilities: fix undefined behavior in bit shift for CAP_TO_MASK Shifting signed 32-bit value by 31 bits is undefined, so changing significant bit to unsigned. The UBSAN warning calltrace like below: UBSAN: shift-out-of-bounds in security/commoncap.c:1252:2 left shift of 1 by 31 places cannot be represented in type 'int' Call Trace: <TASK> dump_stack_lvl+0x7d/0xa5 dump_stack+0x15/0x1b ubsan_epilogue+0xe/0x4e __ubsan_handle_shift_out_of_bounds+0x1e7/0x20c cap_task_prctl+0x561/0x6f0 security_task_prctl+0x5a/0xb0 __x64_sys_prctl+0x61/0x8f0 do_syscall_64+0x58/0x80 entry_SYSCALL_64_after_hwframe+0x63/0xcd </TASK>

In the Linux kernel, the following vulnerability has been resolved: dmaengine: ti: edma: Fix memory allocation size for queue_priority_map Fix a critical memory allocation bug in edma_setup_from_hw() where queue_priority_map was allocated with insufficient memory. The code declared queue_priority_map as s8 (*)[2] (pointer to array of 2 s8), but allocated memory using sizeof(s8) instead of the correct size. This caused out-of-bounds memory writes when accessing: queue_priority_map[i][0] = i; queue_priority_map[i][1] = i; The bug manifested as kernel crashes with "Oops - undefined instruction" on ARM platforms (BeagleBoard-X15) during EDMA driver probe, as the memory corruption triggered kernel hardening features on Clang. Change the allocation to use sizeof(*queue_priority_map) which automatically gets the correct size for the 2D array structure.

In the Linux kernel, the following vulnerability has been resolved: drm/xe: Fix an out-of-bounds shift when invalidating TLB When the size of the range invalidated is larger than rounddown_pow_of_two(ULONG_MAX), The function macro roundup_pow_of_two(length) will hit an out-of-bounds shift [1]. Use a full TLB invalidation for such cases. v2: - Use a define for the range size limit over which we use a full TLB invalidation. (Lucas) - Use a better calculation of the limit. [1]: [ 39.202421] ------------[ cut here ]------------ [ 39.202657] UBSAN: shift-out-of-bounds in ./include/linux/log2.h:57:13 [ 39.202673] shift exponent 64 is too large for 64-bit type 'long unsigned int' [ 39.202688] CPU: 8 UID: 0 PID: 3129 Comm: xe_exec_system_ Tainted: G U 6.14.0+ #10 [ 39.202690] Tainted: [U]=USER [ 39.202690] Hardware name: ASUS System Product Name/PRIME B560M-A AC, BIOS 2001 02/01/2023 [ 39.202691] Call Trace: [ 39.202692] <TASK> [ 39.202695] dump_stack_lvl+0x6e/0xa0 [ 39.202699] ubsan_epilogue+0x5/0x30 [ 39.202701] __ubsan_handle_shift_out_of_bounds.cold+0x61/0xe6 [ 39.202705] xe_gt_tlb_invalidation_range.cold+0x1d/0x3a [xe] [ 39.202800] ? find_held_lock+0x2b/0x80 [ 39.202803] ? mark_held_locks+0x40/0x70 [ 39.202806] xe_svm_invalidate+0x459/0x700 [xe] [ 39.202897] drm_gpusvm_notifier_invalidate+0x4d/0x70 [drm_gpusvm] [ 39.202900] __mmu_notifier_release+0x1f5/0x270 [ 39.202905] exit_mmap+0x40e/0x450 [ 39.202912] __mmput+0x45/0x110 [ 39.202914] exit_mm+0xc5/0x130 [ 39.202916] do_exit+0x21c/0x500 [ 39.202918] ? lockdep_hardirqs_on_prepare+0xdb/0x190 [ 39.202920] do_group_exit+0x36/0xa0 [ 39.202922] get_signal+0x8f8/0x900 [ 39.202926] arch_do_signal_or_restart+0x35/0x100 [ 39.202930] syscall_exit_to_user_mode+0x1fc/0x290 [ 39.202932] do_syscall_64+0xa1/0x180 [ 39.202934] ? do_user_addr_fault+0x59f/0x8a0 [ 39.202937] ? lock_release+0xd2/0x2a0 [ 39.202939] ? do_user_addr_fault+0x5a9/0x8a0 [ 39.202942] ? trace_hardirqs_off+0x4b/0xc0 [ 39.202944] ? clear_bhb_loop+0x25/0x80 [ 39.202946] ? clear_bhb_loop+0x25/0x80 [ 39.202947] ? clear_bhb_loop+0x25/0x80 [ 39.202950] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 39.202952] RIP: 0033:0x7fa945e543e1 [ 39.202961] Code: Unable to access opcode bytes at 0x7fa945e543b7. [ 39.202962] RSP: 002b:00007ffca8fb4170 EFLAGS: 00000293 [ 39.202963] RAX: 000000000000003d RBX: 0000000000000000 RCX: 00007fa945e543e3 [ 39.202964] RDX: 0000000000000000 RSI: 00007ffca8fb41ac RDI: 00000000ffffffff [ 39.202964] RBP: 00007ffca8fb4190 R08: 0000000000000000 R09: 00007fa945f600a0 [ 39.202965] R10: 0000000000000000 R11: 0000000000000293 R12: 0000000000000000 [ 39.202966] R13: 00007fa9460dd310 R14: 00007ffca8fb41ac R15: 0000000000000000 [ 39.202970] </TASK> [ 39.202970] ---[ end trace ]--- (cherry picked from commit b88f48f86500bc0b44b4f73ac66d500a40d320ad)

In the Linux kernel, the following vulnerability has been resolved: audit: fix out-of-bounds read in audit_compare_dname_path() When a watch on dir=/ is combined with an fsnotify event for a single-character name directly under / (e.g., creating /a), an out-of-bounds read can occur in audit_compare_dname_path(). The helper parent_len() returns 1 for "/". In audit_compare_dname_path(), when parentlen equals the full path length (1), the code sets p = path + 1 and pathlen = 1 - 1 = 0. The subsequent loop then dereferences p[pathlen - 1] (i.e., p[-1]), causing an out-of-bounds read. Fix this by adding a pathlen > 0 check to the while loop condition to prevent the out-of-bounds access. [PM: subject tweak, sign-off email fixes]

In the Linux kernel, the following vulnerability has been resolved: i40e: Fix potential invalid access when MAC list is empty list_first_entry() never returns NULL - if the list is empty, it still returns a pointer to an invalid object, leading to potential invalid memory access when dereferenced. Fix this by using list_first_entry_or_null instead of list_first_entry.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: smbdirect: validate data_offset and data_length field of smb_direct_data_transfer If data_offset and data_length of smb_direct_data_transfer struct are invalid, out of bounds issue could happen. This patch validate data_offset and data_length field in recv_done.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix potential oob read in nilfs_btree_check_delete() The function nilfs_btree_check_delete(), which checks whether degeneration to direct mapping occurs before deleting a b-tree entry, causes memory access outside the block buffer when retrieving the maximum key if the root node has no entries. This does not usually happen because b-tree mappings with 0 child nodes are never created by mkfs.nilfs2 or nilfs2 itself. However, it can happen if the b-tree root node read from a device is configured that way, so fix this potential issue by adding a check for that case.

In the Linux kernel, the following vulnerability has been resolved: objtool, nvmet: Fix out-of-bounds stack access in nvmet_ctrl_state_show() The csts_state_names[] array only has six sparse entries, but the iteration code in nvmet_ctrl_state_show() iterates seven, resulting in a potential out-of-bounds stack read. Fix that. Fixes the following warning with an UBSAN kernel: vmlinux.o: warning: objtool: .text.nvmet_ctrl_state_show: unexpected end of section

In the Linux kernel, the following vulnerability has been resolved: drm/fb-helper: Fix out-of-bounds access Clip memory range to screen-buffer size to avoid out-of-bounds access in fbdev deferred I/O's damage handling. Fbdev's deferred I/O can only track pages. From the range of pages, the damage handler computes the clipping rectangle for the display update. If the fbdev screen buffer ends near the beginning of a page, that page could contain more scanlines. The damage handler would then track these non-existing scanlines as dirty and provoke an out-of-bounds access during the screen update. Hence, clip the maximum memory range to the size of the screen buffer. While at it, rename the variables min/max to min_off/max_off in drm_fb_helper_deferred_io(). This avoids confusion with the macros of the same name.

In the Linux kernel, the following vulnerability has been resolved: jfs: fix out-of-bounds in dbNextAG() and diAlloc() In dbNextAG() , there is no check for the case where bmp->db_numag is greater or same than MAXAG due to a polluted image, which causes an out-of-bounds. Therefore, a bounds check should be added in dbMount(). And in dbNextAG(), a check for the case where agpref is greater than bmp->db_numag should be added, so an out-of-bounds exception should be prevented. Additionally, a check for the case where agno is greater or same than MAXAG should be added in diAlloc() to prevent out-of-bounds.

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: remove unused C2H event ID RTW89_MAC_C2H_FUNC_READ_WOW_CAM to prevent out-of-bounds reading The handler of firmware C2H event RTW89_MAC_C2H_FUNC_READ_WOW_CAM isn't implemented, but driver expects number of handlers is NUM_OF_RTW89_MAC_C2H_FUNC_WOW causing out-of-bounds access. Fix it by removing ID. Addresses-Coverity-ID: 1598775 ("Out-of-bounds read")

In the Linux kernel, the following vulnerability has been resolved: clk: bcm: rpi: Prevent out-of-bounds access The while loop in raspberrypi_discover_clocks() relies on the assumption that the id of the last clock element is zero. Because this data comes from the Videocore firmware and it doesn't guarantuee such a behavior this could lead to out-of-bounds access. So fix this by providing a sentinel element.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Decrement TID on RX peer frag setup error handling Currently, TID is not decremented before peer cleanup, during error handling path of ath12k_dp_rx_peer_frag_setup(). This could lead to out-of-bounds access in peer->rx_tid[]. Hence, add a decrement operation for TID, before peer cleanup to ensures proper cleanup and prevents out-of-bounds access issues when the RX peer frag setup fails. Found during code review. Compile tested only.

In the Linux kernel, the following vulnerability has been resolved: habanalabs/gaudi: fix shift out of bounds When validating NIC queues, queue offset calculation must be performed only for NIC queues.

In the Linux kernel, the following vulnerability has been resolved: bpf: add check for invalid name in btf_name_valid_section() If the length of the name string is 1 and the value of name[0] is NULL byte, an OOB vulnerability occurs in btf_name_valid_section() and the return value is true, so the invalid name passes the check. To solve this, you need to check if the first position is NULL byte and if the first character is printable.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix mc_data out-of-bounds read warning Clear warning that read mc_data[i-1] may out-of-bounds.

In the Linux kernel, the following vulnerability has been resolved: usb: core: config: Prevent OOB read in SS endpoint companion parsing usb_parse_ss_endpoint_companion() checks descriptor type before length, enabling a potentially odd read outside of the buffer size. Fix this up by checking the size first before looking at any of the fields in the descriptor.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix out-of-bounds read of df_v1_7_channel_number Check the fb_channel_number range to avoid the array out-of-bounds read error

In the Linux kernel, the following vulnerability has been resolved: media: imx-jpeg: Align upwards buffer size The hardware can support any image size WxH, with arbitrary W (image width) and H (image height) dimensions. Align upwards buffer size for both encoder and decoder. and leave the picture resolution unchanged. For decoder, the risk of memory out of bounds can be avoided. For both encoder and decoder, the driver will lift the limitation of resolution alignment. For example, the decoder can support jpeg whose resolution is 227x149 the encoder can support nv12 1080P, won't change it to 1920x1072.

In the Linux kernel, the following vulnerability has been resolved: um: Fix out-of-bounds read in LDT setup syscall_stub_data() expects the data_count parameter to be the number of longs, not bytes. ================================================================== BUG: KASAN: stack-out-of-bounds in syscall_stub_data+0x70/0xe0 Read of size 128 at addr 000000006411f6f0 by task swapper/1 CPU: 0 PID: 1 Comm: swapper Not tainted 5.18.0+ #18 Call Trace: show_stack.cold+0x166/0x2a7 __dump_stack+0x3a/0x43 dump_stack_lvl+0x1f/0x27 print_report.cold+0xdb/0xf81 kasan_report+0x119/0x1f0 kasan_check_range+0x3a3/0x440 memcpy+0x52/0x140 syscall_stub_data+0x70/0xe0 write_ldt_entry+0xac/0x190 init_new_ldt+0x515/0x960 init_new_context+0x2c4/0x4d0 mm_init.constprop.0+0x5ed/0x760 mm_alloc+0x118/0x170 0x60033f48 do_one_initcall+0x1d7/0x860 0x60003e7b kernel_init+0x6e/0x3d4 new_thread_handler+0x1e7/0x2c0 The buggy address belongs to stack of task swapper/1 and is located at offset 64 in frame: init_new_ldt+0x0/0x960 This frame has 2 objects: [32, 40) 'addr' [64, 80) 'desc' ==================================================================

In the Linux kernel, the following vulnerability has been resolved: ASoC: SOF: ipc3-topology: Correct get_control_data for non bytes payload It is possible to craft a topology where sof_get_control_data() would do out of bounds access because it expects that it is only called when the payload is bytes type. Confusingly it also handles other types of controls, but the payload parsing implementation is only valid for bytes. Fix the code to count the non bytes controls and instead of storing a pointer to sof_abi_hdr in sof_widget_data (which is only valid for bytes), store the pointer to the data itself and add a new member to save the size of the data. In case of non bytes controls we store the pointer to the chanv itself, which is just an array of values at the end. In case of bytes control, drop the wrong cdata->data (wdata[i].pdata) check against NULL since it is incorrect and invalid in this context. The data is pointing to the end of cdata struct, so it should never be null.

In the Linux kernel, the following vulnerability has been resolved: iio: adc: mp2629: fix potential array out of bound access Add sentinel at end of maps to avoid potential array out of bound access in iio core.

In the Linux kernel, the following vulnerability has been resolved: spmi: trace: fix stack-out-of-bound access in SPMI tracing functions trace_spmi_write_begin() and trace_spmi_read_end() both call memcpy() with a length of "len + 1". This leads to one extra byte being read beyond the end of the specified buffer. Fix this out-of-bound memory access by using a length of "len" instead. Here is a KASAN log showing the issue: BUG: KASAN: stack-out-of-bounds in trace_event_raw_event_spmi_read_end+0x1d0/0x234 Read of size 2 at addr ffffffc0265b7540 by task thermal@2.0-ser/1314 ... Call trace: dump_backtrace+0x0/0x3e8 show_stack+0x2c/0x3c dump_stack_lvl+0xdc/0x11c print_address_description+0x74/0x384 kasan_report+0x188/0x268 kasan_check_range+0x270/0x2b0 memcpy+0x90/0xe8 trace_event_raw_event_spmi_read_end+0x1d0/0x234 spmi_read_cmd+0x294/0x3ac spmi_ext_register_readl+0x84/0x9c regmap_spmi_ext_read+0x144/0x1b0 [regmap_spmi] _regmap_raw_read+0x40c/0x754 regmap_raw_read+0x3a0/0x514 regmap_bulk_read+0x418/0x494 adc5_gen3_poll_wait_hs+0xe8/0x1e0 [qcom_spmi_adc5_gen3] ... __arm64_sys_read+0x4c/0x60 invoke_syscall+0x80/0x218 el0_svc_common+0xec/0x1c8 ... addr ffffffc0265b7540 is located in stack of task thermal@2.0-ser/1314 at offset 32 in frame: adc5_gen3_poll_wait_hs+0x0/0x1e0 [qcom_spmi_adc5_gen3] this frame has 1 object: [32, 33) 'status' Memory state around the buggy address: ffffffc0265b7400: 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1 ffffffc0265b7480: 04 f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00 >ffffffc0265b7500: 00 00 00 00 f1 f1 f1 f1 01 f3 f3 f3 00 00 00 00 ^ ffffffc0265b7580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffffffc0265b7600: f1 f1 f1 f1 01 f2 07 f2 f2 f2 01 f3 00 00 00 00 ==================================================================

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Validate UAC3 cluster segment descriptors UAC3 class segment descriptors need to be verified whether their sizes match with the declared lengths and whether they fit with the allocated buffer sizes, too. Otherwise malicious firmware may lead to the unexpected OOB accesses.

In the Linux kernel, the following vulnerability has been resolved: mm/mempolicy: fix get_nodes out of bound access When user specified more nodes than supported, get_nodes will access nmask array out of bounds.

In the Linux kernel, the following vulnerability has been resolved: batman-adv: fix OOB read/write in network-coding decode batadv_nc_skb_decode_packet() trusts coded_len and checks only against skb->len. XOR starts at sizeof(struct batadv_unicast_packet), reducing payload headroom, and the source skb length is not verified, allowing an out-of-bounds read and a small out-of-bounds write. Validate that coded_len fits within the payload area of both destination and source sk_buffs before XORing.

In the Linux kernel, the following vulnerability has been resolved: md-raid10: fix KASAN warning There's a KASAN warning in raid10_remove_disk when running the lvm test lvconvert-raid-reshape.sh. We fix this warning by verifying that the value "number" is valid. BUG: KASAN: slab-out-of-bounds in raid10_remove_disk+0x61/0x2a0 [raid10] Read of size 8 at addr ffff889108f3d300 by task mdX_raid10/124682 CPU: 3 PID: 124682 Comm: mdX_raid10 Not tainted 5.19.0-rc6 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x34/0x44 print_report.cold+0x45/0x57a ? __lock_text_start+0x18/0x18 ? raid10_remove_disk+0x61/0x2a0 [raid10] kasan_report+0xa8/0xe0 ? raid10_remove_disk+0x61/0x2a0 [raid10] raid10_remove_disk+0x61/0x2a0 [raid10] Buffer I/O error on dev dm-76, logical block 15344, async page read ? __mutex_unlock_slowpath.constprop.0+0x1e0/0x1e0 remove_and_add_spares+0x367/0x8a0 [md_mod] ? super_written+0x1c0/0x1c0 [md_mod] ? mutex_trylock+0xac/0x120 ? _raw_spin_lock+0x72/0xc0 ? _raw_spin_lock_bh+0xc0/0xc0 md_check_recovery+0x848/0x960 [md_mod] raid10d+0xcf/0x3360 [raid10] ? sched_clock_cpu+0x185/0x1a0 ? rb_erase+0x4d4/0x620 ? var_wake_function+0xe0/0xe0 ? psi_group_change+0x411/0x500 ? preempt_count_sub+0xf/0xc0 ? _raw_spin_lock_irqsave+0x78/0xc0 ? __lock_text_start+0x18/0x18 ? raid10_sync_request+0x36c0/0x36c0 [raid10] ? preempt_count_sub+0xf/0xc0 ? _raw_spin_unlock_irqrestore+0x19/0x40 ? del_timer_sync+0xa9/0x100 ? try_to_del_timer_sync+0xc0/0xc0 ? _raw_spin_lock_irqsave+0x78/0xc0 ? __lock_text_start+0x18/0x18 ? _raw_spin_unlock_irq+0x11/0x24 ? __list_del_entry_valid+0x68/0xa0 ? finish_wait+0xa3/0x100 md_thread+0x161/0x260 [md_mod] ? unregister_md_personality+0xa0/0xa0 [md_mod] ? _raw_spin_lock_irqsave+0x78/0xc0 ? prepare_to_wait_event+0x2c0/0x2c0 ? unregister_md_personality+0xa0/0xa0 [md_mod] kthread+0x148/0x180 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x1f/0x30 </TASK> Allocated by task 124495: kasan_save_stack+0x1e/0x40 __kasan_kmalloc+0x80/0xa0 setup_conf+0x140/0x5c0 [raid10] raid10_run+0x4cd/0x740 [raid10] md_run+0x6f9/0x1300 [md_mod] raid_ctr+0x2531/0x4ac0 [dm_raid] dm_table_add_target+0x2b0/0x620 [dm_mod] table_load+0x1c8/0x400 [dm_mod] ctl_ioctl+0x29e/0x560 [dm_mod] dm_compat_ctl_ioctl+0x7/0x20 [dm_mod] __do_compat_sys_ioctl+0xfa/0x160 do_syscall_64+0x90/0xc0 entry_SYSCALL_64_after_hwframe+0x46/0xb0 Last potentially related work creation: kasan_save_stack+0x1e/0x40 __kasan_record_aux_stack+0x9e/0xc0 kvfree_call_rcu+0x84/0x480 timerfd_release+0x82/0x140 L __fput+0xfa/0x400 task_work_run+0x80/0xc0 exit_to_user_mode_prepare+0x155/0x160 syscall_exit_to_user_mode+0x12/0x40 do_syscall_64+0x42/0xc0 entry_SYSCALL_64_after_hwframe+0x46/0xb0 Second to last potentially related work creation: kasan_save_stack+0x1e/0x40 __kasan_record_aux_stack+0x9e/0xc0 kvfree_call_rcu+0x84/0x480 timerfd_release+0x82/0x140 __fput+0xfa/0x400 task_work_run+0x80/0xc0 exit_to_user_mode_prepare+0x155/0x160 syscall_exit_to_user_mode+0x12/0x40 do_syscall_64+0x42/0xc0 entry_SYSCALL_64_after_hwframe+0x46/0xb0 The buggy address belongs to the object at ffff889108f3d200 which belongs to the cache kmalloc-256 of size 256 The buggy address is located 0 bytes to the right of 256-byte region [ffff889108f3d200, ffff889108f3d300) The buggy address belongs to the physical page: page:000000007ef2a34c refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1108f3c head:000000007ef2a34c order:2 compound_mapcount:0 compound_pincount:0 flags: 0x4000000000010200(slab|head|zone=2) raw: 4000000000010200 0000000000000000 dead000000000001 ffff889100042b40 raw: 0000000000000000 0000000080200020 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff889108f3d200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff889108f3d280: 00 00 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Check the count value of channel spec to prevent out-of-bounds reads This patch fixes slab-out-of-bounds reads in brcmfmac that occur in brcmf_construct_chaninfo() and brcmf_enable_bw40_2g() when the count value of channel specifications provided by the device is greater than the length of 'list->element[]', decided by the size of the 'list' allocated with kzalloc(). The patch adds checks that make the functions free the buffer and return -EINVAL if that is the case. Note that the negative return is handled by the caller, brcmf_setup_wiphybands() or brcmf_cfg80211_attach(). Found by a modified version of syzkaller. Crash Report from brcmf_construct_chaninfo(): ================================================================== BUG: KASAN: slab-out-of-bounds in brcmf_setup_wiphybands+0x1238/0x1430 Read of size 4 at addr ffff888115f24600 by task kworker/0:2/1896 CPU: 0 PID: 1896 Comm: kworker/0:2 Tainted: G W O 5.14.0+ #132 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Workqueue: usb_hub_wq hub_event Call Trace: dump_stack_lvl+0x57/0x7d print_address_description.constprop.0.cold+0x93/0x334 kasan_report.cold+0x83/0xdf brcmf_setup_wiphybands+0x1238/0x1430 brcmf_cfg80211_attach+0x2118/0x3fd0 brcmf_attach+0x389/0xd40 brcmf_usb_probe+0x12de/0x1690 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_set_configuration+0x984/0x1770 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_new_device.cold+0x463/0xf66 hub_event+0x10d5/0x3330 process_one_work+0x873/0x13e0 worker_thread+0x8b/0xd10 kthread+0x379/0x450 ret_from_fork+0x1f/0x30 Allocated by task 1896: kasan_save_stack+0x1b/0x40 __kasan_kmalloc+0x7c/0x90 kmem_cache_alloc_trace+0x19e/0x330 brcmf_setup_wiphybands+0x290/0x1430 brcmf_cfg80211_attach+0x2118/0x3fd0 brcmf_attach+0x389/0xd40 brcmf_usb_probe+0x12de/0x1690 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_set_configuration+0x984/0x1770 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_new_device.cold+0x463/0xf66 hub_event+0x10d5/0x3330 process_one_work+0x873/0x13e0 worker_thread+0x8b/0xd10 kthread+0x379/0x450 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff888115f24000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 1536 bytes inside of 2048-byte region [ffff888115f24000, ffff888115f24800) Memory state around the buggy address: ffff888115f24500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888115f24580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff888115f24600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff888115f24680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888115f24700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ================================================================== Crash Report from brcmf_enable_bw40_2g(): ========== ---truncated---

In the Linux kernel, the following vulnerability has been resolved: module: fix [e_shstrndx].sh_size=0 OOB access It is trivial to craft a module to trigger OOB access in this line: if (info->secstrings[strhdr->sh_size - 1] != '\0') { BUG: unable to handle page fault for address: ffffc90000aa0fff PGD 100000067 P4D 100000067 PUD 100066067 PMD 10436f067 PTE 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 7 PID: 1215 Comm: insmod Not tainted 5.18.0-rc5-00007-g9bf578647087-dirty #10 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014 RIP: 0010:load_module+0x19b/0x2391 [rebased patch onto modules-next]

In the Linux kernel, the following vulnerability has been resolved: riscv: fix reserved memory setup Currently, RISC-V sets up reserved memory using the "early" copy of the device tree. As a result, when trying to get a reserved memory region using of_reserved_mem_lookup(), the pointer to reserved memory regions is using the early, pre-virtual-memory address which causes a kernel panic when trying to use the buffer's name: Unable to handle kernel paging request at virtual address 00000000401c31ac Oops [#1] Modules linked in: CPU: 0 PID: 0 Comm: swapper Not tainted 6.0.0-rc1-00001-g0d9d6953d834 #1 Hardware name: Microchip PolarFire-SoC Icicle Kit (DT) epc : string+0x4a/0xea ra : vsnprintf+0x1e4/0x336 epc : ffffffff80335ea0 ra : ffffffff80338936 sp : ffffffff81203be0 gp : ffffffff812e0a98 tp : ffffffff8120de40 t0 : 0000000000000000 t1 : ffffffff81203e28 t2 : 7265736572203a46 s0 : ffffffff81203c20 s1 : ffffffff81203e28 a0 : ffffffff81203d22 a1 : 0000000000000000 a2 : ffffffff81203d08 a3 : 0000000081203d21 a4 : ffffffffffffffff a5 : 00000000401c31ac a6 : ffff0a00ffffff04 a7 : ffffffffffffffff s2 : ffffffff81203d08 s3 : ffffffff81203d00 s4 : 0000000000000008 s5 : ffffffff000000ff s6 : 0000000000ffffff s7 : 00000000ffffff00 s8 : ffffffff80d9821a s9 : ffffffff81203d22 s10: 0000000000000002 s11: ffffffff80d9821c t3 : ffffffff812f3617 t4 : ffffffff812f3617 t5 : ffffffff812f3618 t6 : ffffffff81203d08 status: 0000000200000100 badaddr: 00000000401c31ac cause: 000000000000000d [<ffffffff80338936>] vsnprintf+0x1e4/0x336 [<ffffffff80055ae2>] vprintk_store+0xf6/0x344 [<ffffffff80055d86>] vprintk_emit+0x56/0x192 [<ffffffff80055ed8>] vprintk_default+0x16/0x1e [<ffffffff800563d2>] vprintk+0x72/0x80 [<ffffffff806813b2>] _printk+0x36/0x50 [<ffffffff8068af48>] print_reserved_mem+0x1c/0x24 [<ffffffff808057ec>] paging_init+0x528/0x5bc [<ffffffff808031ae>] setup_arch+0xd0/0x592 [<ffffffff8080070e>] start_kernel+0x82/0x73c early_init_fdt_scan_reserved_mem() takes no arguments as it operates on initial_boot_params, which is populated by early_init_dt_verify(). On RISC-V, early_init_dt_verify() is called twice. Once, directly, in setup_arch() if CONFIG_BUILTIN_DTB is not enabled and once indirectly, very early in the boot process, by parse_dtb() when it calls early_init_dt_scan_nodes(). This first call uses dtb_early_va to set initial_boot_params, which is not usable later in the boot process when early_init_fdt_scan_reserved_mem() is called. On arm64 for example, the corresponding call to early_init_dt_scan_nodes() uses fixmap addresses and doesn't suffer the same fate. Move early_init_fdt_scan_reserved_mem() further along the boot sequence, after the direct call to early_init_dt_verify() in setup_arch() so that the names use the correct virtual memory addresses. The above supposed that CONFIG_BUILTIN_DTB was not set, but should work equally in the case where it is - unflatted_and_copy_device_tree() also updates initial_boot_params.

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: smm: number of GPRs in the SMRAM image depends on the image format On 64 bit host, if the guest doesn't have X86_FEATURE_LM, KVM will access 16 gprs to 32-bit smram image, causing out-ouf-bound ram access. On 32 bit host, the rsm_load_state_64/enter_smm_save_state_64 is compiled out, thus access overflow can't happen.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: mtk_eth_soc: out of bounds read in mtk_hwlro_get_fdir_entry() The "fsp->location" variable comes from user via ethtool_get_rxnfc(). Check that it is valid to prevent an out of bounds read.

In the Linux kernel, the following vulnerability has been resolved: ACPI: CPPC: Avoid out of bounds access when parsing _CPC data If the NumEntries field in the _CPC return package is less than 2, do not attempt to access the "Revision" element of that package, because it may not be present then. BugLink: https://lore.kernel.org/lkml/20220322143534.GC32582@xsang-OptiPlex-9020/

In the Linux kernel, the following vulnerability has been resolved: i40e: remove read access to debugfs files The 'command' and 'netdev_ops' debugfs files are a legacy debugging interface supported by the i40e driver since its early days by commit 02e9c290814c ("i40e: debugfs interface"). Both of these debugfs files provide a read handler which is mostly useless, and which is implemented with questionable logic. They both use a static 256 byte buffer which is initialized to the empty string. In the case of the 'command' file this buffer is literally never used and simply wastes space. In the case of the 'netdev_ops' file, the last command written is saved here. On read, the files contents are presented as the name of the device followed by a colon and then the contents of their respective static buffer. For 'command' this will always be "<device>: ". For 'netdev_ops', this will be "<device>: <last command written>". But note the buffer is shared between all devices operated by this module. At best, it is mostly meaningless information, and at worse it could be accessed simultaneously as there doesn't appear to be any locking mechanism. We have also recently received multiple reports for both read functions about their use of snprintf and potential overflow that could result in reading arbitrary kernel memory. For the 'command' file, this is definitely impossible, since the static buffer is always zero and never written to. For the 'netdev_ops' file, it does appear to be possible, if the user carefully crafts the command input, it will be copied into the buffer, which could be large enough to cause snprintf to truncate, which then causes the copy_to_user to read beyond the length of the buffer allocated by kzalloc. A minimal fix would be to replace snprintf() with scnprintf() which would cap the return to the number of bytes written, preventing an overflow. A more involved fix would be to drop the mostly useless static buffers, saving 512 bytes and modifying the read functions to stop needing those as input. Instead, lets just completely drop the read access to these files. These are debug interfaces exposed as part of debugfs, and I don't believe that dropping read access will break any script, as the provided output is pretty useless. You can find the netdev name through other more standard interfaces, and the 'netdev_ops' interface can easily result in garbage if you issue simultaneous writes to multiple devices at once. In order to properly remove the i40e_dbg_netdev_ops_buf, we need to refactor its write function to avoid using the static buffer. Instead, use the same logic as the i40e_dbg_command_write, with an allocated buffer. Update the code to use this instead of the static buffer, and ensure we free the buffer on exit. This fixes simultaneous writes to 'netdev_ops' on multiple devices, and allows us to remove the now unused static buffer along with removing the read access.

An issue was discovered in the Linux kernel before 6.2. The ntfs3 subsystem does not properly check for correctness during disk reads, leading to an out-of-bounds read in ntfs_set_ea in fs/ntfs3/xattr.c.

In the Linux kernel, the following vulnerability has been resolved: ixgbe: fix incorrect map used in eee linkmode incorrectly used ixgbe_lp_map in loops intended to populate the supported and advertised EEE linkmode bitmaps based on ixgbe_ls_map. This results in incorrect bit setting and potential out-of-bounds access, since ixgbe_lp_map and ixgbe_ls_map have different sizes and purposes. ixgbe_lp_map[i] -> ixgbe_ls_map[i] Use ixgbe_ls_map for supported and advertised linkmodes, and keep ixgbe_lp_map usage only for link partner (lp_advertised) mapping.

In the Linux kernel, the following vulnerability has been resolved: ASoC: hdmi-codec: Fix OOB memory accesses Correct size of iec_status array by changing it to the size of status array of the struct snd_aes_iec958. This fixes out-of-bounds slab read accesses made by memcpy() of the hdmi-codec driver. This problem is reported by KASAN.

In the Linux kernel, the following vulnerability has been resolved: rcu: Fix rcu_read_unlock() deadloop due to IRQ work During rcu_read_unlock_special(), if this happens during irq_exit(), we can lockup if an IPI is issued. This is because the IPI itself triggers the irq_exit() path causing a recursive lock up. This is precisely what Xiongfeng found when invoking a BPF program on the trace_tick_stop() tracepoint As shown in the trace below. Fix by managing the irq_work state correctly. irq_exit() __irq_exit_rcu() /* in_hardirq() returns false after this */ preempt_count_sub(HARDIRQ_OFFSET) tick_irq_exit() tick_nohz_irq_exit() tick_nohz_stop_sched_tick() trace_tick_stop() /* a bpf prog is hooked on this trace point */ __bpf_trace_tick_stop() bpf_trace_run2() rcu_read_unlock_special() /* will send a IPI to itself */ irq_work_queue_on(&rdp->defer_qs_iw, rdp->cpu); A simple reproducer can also be obtained by doing the following in tick_irq_exit(). It will hang on boot without the patch: static inline void tick_irq_exit(void) { + rcu_read_lock(); + WRITE_ONCE(current->rcu_read_unlock_special.b.need_qs, true); + rcu_read_unlock(); + [neeraj: Apply Frederic's suggested fix for PREEMPT_RT]

In the Linux kernel, the following vulnerability has been resolved: ASoC: codecs: wc938x: fix accessing array out of bounds for enum type Accessing enums using integer would result in array out of bounds access on platforms like aarch64 where sizeof(long) is 8 compared to enum size which is 4 bytes. Fix this by using enumerated items instead of integers.

In the Linux kernel, the following vulnerability has been resolved: ASoC: codecs: rx-macro: fix accessing compander for aux AUX interpolator does not have compander, so check before accessing compander data for this. Without this checkan array of out bounds access will be made in comp_enabled[] array.