In the Linux kernel, the following vulnerability has been resolved: ibmvnic: Use kernel helpers for hex dumps Previously, when the driver was printing hex dumps, the buffer was cast to an 8 byte long and printed using string formatters. If the buffer size was not a multiple of 8 then a read buffer overflow was possible. Therefore, create a new ibmvnic function that loops over a buffer and calls hex_dump_to_buffer instead. This patch address KASAN reports like the one below: ibmvnic 30000003 env3: Login Buffer: ibmvnic 30000003 env3: 01000000af000000 <...> ibmvnic 30000003 env3: 2e6d62692e736261 ibmvnic 30000003 env3: 65050003006d6f63 ================================================================== BUG: KASAN: slab-out-of-bounds in ibmvnic_login+0xacc/0xffc [ibmvnic] Read of size 8 at addr c0000001331a9aa8 by task ip/17681 <...> Allocated by task 17681: <...> ibmvnic_login+0x2f0/0xffc [ibmvnic] ibmvnic_open+0x148/0x308 [ibmvnic] __dev_open+0x1ac/0x304 <...> The buggy address is located 168 bytes inside of allocated 175-byte region [c0000001331a9a00, c0000001331a9aaf) <...> ================================================================= ibmvnic 30000003 env3: 000000000033766e

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix array bounds error with may_goto may_goto uses an additional 8 bytes on the stack, which causes the interpreters[] array to go out of bounds when calculating index by stack_size. 1. If a BPF program is rewritten, re-evaluate the stack size. For non-JIT cases, reject loading directly. 2. For non-JIT cases, calculating interpreters[idx] may still cause out-of-bounds array access, and just warn about it. 3. For jit_requested cases, the execution of bpf_func also needs to be warned. So move the definition of function __bpf_prog_ret0_warn out of the macro definition CONFIG_BPF_JIT_ALWAYS_ON.

In the Linux kernel, the following vulnerability has been resolved: usbnet: ipheth: use static NDP16 location in URB Original code allowed for the start of NDP16 to be anywhere within the URB based on the `wNdpIndex` value in NTH16. Only the start position of NDP16 was checked, so it was possible for even the fixed-length part of NDP16 to extend past the end of URB, leading to an out-of-bounds read. On iOS devices, the NDP16 header always directly follows NTH16. Rely on and check for this specific format. This, along with NCM-specific minimal URB length check that already exists, will ensure that the fixed-length part of NDP16 plus a set amount of DPEs fit within the URB. Note that this commit alone does not fully address the OoB read. The limit on the amount of DPEs needs to be enforced separately.

In the Linux kernel, the following vulnerability has been resolved: iscsi_ibft: Fix UBSAN shift-out-of-bounds warning in ibft_attr_show_nic() When performing an iSCSI boot using IPv6, iscsistart still reads the /sys/firmware/ibft/ethernetX/subnet-mask entry. Since the IPv6 prefix length is 64, this causes the shift exponent to become negative, triggering a UBSAN warning. As the concept of a subnet mask does not apply to IPv6, the value is set to ~0 to suppress the warning message.

In the Linux kernel, the following vulnerability has been resolved: vlan: enforce underlying device type Currently, VLAN devices can be created on top of non-ethernet devices. Besides the fact that it doesn't make much sense, this also causes a bug which leaks the address of a kernel function to usermode. When creating a VLAN device, we initialize GARP (garp_init_applicant) and MRP (mrp_init_applicant) for the underlying device. As part of the initialization process, we add the multicast address of each applicant to the underlying device, by calling dev_mc_add. __dev_mc_add uses dev->addr_len to determine the length of the new multicast address. This causes an out-of-bounds read if dev->addr_len is greater than 6, since the multicast addresses provided by GARP and MRP are only 6 bytes long. This behaviour can be reproduced using the following commands: ip tunnel add gretest mode ip6gre local ::1 remote ::2 dev lo ip l set up dev gretest ip link add link gretest name vlantest type vlan id 100 Then, the following command will display the address of garp_pdu_rcv: ip maddr show | grep 01:80:c2:00:00:21 Fix the bug by enforcing the type of the underlying device during VLAN device initialization.

In the Linux kernel, the following vulnerability has been resolved: drm/v3d: Prevent out of bounds access in performance query extensions Check that the number of perfmons userspace is passing in the copy and reset extensions is not greater than the internal kernel storage where the ids will be copied into. (cherry picked from commit f32b5128d2c440368b5bf3a7a356823e235caabb)

In the Linux kernel, the following vulnerability has been resolved: tap: add missing verification for short frame The cited commit missed to check against the validity of the frame length in the tap_get_user_xdp() path, which could cause a corrupted skb to be sent downstack. Even before the skb is transmitted, the tap_get_user_xdp()-->skb_set_network_header() may assume the size is more than ETH_HLEN. Once transmitted, this could either cause out-of-bound access beyond the actual length, or confuse the underlayer with incorrect or inconsistent header length in the skb metadata. In the alternative path, tap_get_user() already prohibits short frame which has the length less than Ethernet header size from being transmitted. This is to drop any frame shorter than the Ethernet header size just like how tap_get_user() does. CVE: CVE-2024-41090

In the Linux kernel, the following vulnerability has been resolved: scsi: qedi: Fix crash while reading debugfs attribute The qedi_dbg_do_not_recover_cmd_read() function invokes sprintf() directly on a __user pointer, which results into the crash. To fix this issue, use a small local stack buffer for sprintf() and then call simple_read_from_buffer(), which in turns make the copy_to_user() call. BUG: unable to handle page fault for address: 00007f4801111000 PGD 8000000864df6067 P4D 8000000864df6067 PUD 864df7067 PMD 846028067 PTE 0 Oops: 0002 [#1] PREEMPT SMP PTI Hardware name: HPE ProLiant DL380 Gen10/ProLiant DL380 Gen10, BIOS U30 06/15/2023 RIP: 0010:memcpy_orig+0xcd/0x130 RSP: 0018:ffffb7a18c3ffc40 EFLAGS: 00010202 RAX: 00007f4801111000 RBX: 00007f4801111000 RCX: 000000000000000f RDX: 000000000000000f RSI: ffffffffc0bfd7a0 RDI: 00007f4801111000 RBP: ffffffffc0bfd7a0 R08: 725f746f6e5f6f64 R09: 3d7265766f636572 R10: ffffb7a18c3ffd08 R11: 0000000000000000 R12: 00007f4881110fff R13: 000000007fffffff R14: ffffb7a18c3ffca0 R15: ffffffffc0bfd7af FS: 00007f480118a740(0000) GS:ffff98e38af00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f4801111000 CR3: 0000000864b8e001 CR4: 00000000007706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> ? __die_body+0x1a/0x60 ? page_fault_oops+0x183/0x510 ? exc_page_fault+0x69/0x150 ? asm_exc_page_fault+0x22/0x30 ? memcpy_orig+0xcd/0x130 vsnprintf+0x102/0x4c0 sprintf+0x51/0x80 qedi_dbg_do_not_recover_cmd_read+0x2f/0x50 [qedi 6bcfdeeecdea037da47069eca2ba717c84a77324] full_proxy_read+0x50/0x80 vfs_read+0xa5/0x2e0 ? folio_add_new_anon_rmap+0x44/0xa0 ? set_pte_at+0x15/0x30 ? do_pte_missing+0x426/0x7f0 ksys_read+0xa5/0xe0 do_syscall_64+0x58/0x80 ? __count_memcg_events+0x46/0x90 ? count_memcg_event_mm+0x3d/0x60 ? handle_mm_fault+0x196/0x2f0 ? do_user_addr_fault+0x267/0x890 ? exc_page_fault+0x69/0x150 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7f4800f20b4d

In the Linux kernel, the following vulnerability has been resolved: xfs: add bounds checking to xlog_recover_process_data There is a lack of verification of the space occupied by fixed members of xlog_op_header in the xlog_recover_process_data. We can create a crafted image to trigger an out of bounds read by following these steps: 1) Mount an image of xfs, and do some file operations to leave records 2) Before umounting, copy the image for subsequent steps to simulate abnormal exit. Because umount will ensure that tail_blk and head_blk are the same, which will result in the inability to enter xlog_recover_process_data 3) Write a tool to parse and modify the copied image in step 2 4) Make the end of the xlog_op_header entries only 1 byte away from xlog_rec_header->h_size 5) xlog_rec_header->h_num_logops++ 6) Modify xlog_rec_header->h_crc Fix: Add a check to make sure there is sufficient space to access fixed members of xlog_op_header.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix out of bounds read in smb2_sess_setup ksmbd does not consider the case of that smb2 session setup is in compound request. If this is the second payload of the compound, OOB read issue occurs while processing the first payload in the smb2_sess_setup().

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix out-of-bound read in smb2_write ksmbd_smb2_check_message doesn't validate hdr->NextCommand. If ->NextCommand is bigger than Offset + Length of smb2 write, It will allow oversized smb2 write length. It will cause OOB read in smb2_write.

In the Linux kernel, the following vulnerability has been resolved: xfs: don't walk off the end of a directory data block This adds sanity checks for xfs_dir2_data_unused and xfs_dir2_data_entry to make sure don't stray beyond valid memory region. Before patching, the loop simply checks that the start offset of the dup and dep is within the range. So in a crafted image, if last entry is xfs_dir2_data_unused, we can change dup->length to dup->length-1 and leave 1 byte of space. In the next traversal, this space will be considered as dup or dep. We may encounter an out of bound read when accessing the fixed members. In the patch, we make sure that the remaining bytes large enough to hold an unused entry before accessing xfs_dir2_data_unused and xfs_dir2_data_unused is XFS_DIR2_DATA_ALIGN byte aligned. We also make sure that the remaining bytes large enough to hold a dirent with a single-byte name before accessing xfs_dir2_data_entry.

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: check n_ssids before accessing the ssids In some versions of cfg80211, the ssids poinet might be a valid one even though n_ssids is 0. Accessing the pointer in this case will cuase an out-of-bound access. Fix this by checking n_ssids first.

In the Linux kernel, the following vulnerability has been resolved: jffs2: prevent xattr node from overflowing the eraseblock Add a check to make sure that the requested xattr node size is no larger than the eraseblock minus the cleanmarker. Unlike the usual inode nodes, the xattr nodes aren't split into parts and spread across multiple eraseblocks, which means that a xattr node must not occupy more than one eraseblock. If the requested xattr value is too large, the xattr node can spill onto the next eraseblock, overwriting the nodes and causing errors such as: jffs2: argh. node added in wrong place at 0x0000b050(2) jffs2: nextblock 0x0000a000, expected at 0000b00c jffs2: error: (823) do_verify_xattr_datum: node CRC failed at 0x01e050, read=0xfc892c93, calc=0x000000 jffs2: notice: (823) jffs2_get_inode_nodes: Node header CRC failed at 0x01e00c. {848f,2fc4,0fef511f,59a3d171} jffs2: Node at 0x0000000c with length 0x00001044 would run over the end of the erase block jffs2: Perhaps the file system was created with the wrong erase size? jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000010: 0x1044 instead This breaks the filesystem and can lead to KASAN crashes such as: BUG: KASAN: slab-out-of-bounds in jffs2_sum_add_kvec+0x125e/0x15d0 Read of size 4 at addr ffff88802c31e914 by task repro/830 CPU: 0 PID: 830 Comm: repro Not tainted 6.9.0-rc3+ #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0xc6/0x120 print_report+0xc4/0x620 ? __virt_addr_valid+0x308/0x5b0 kasan_report+0xc1/0xf0 ? jffs2_sum_add_kvec+0x125e/0x15d0 ? jffs2_sum_add_kvec+0x125e/0x15d0 jffs2_sum_add_kvec+0x125e/0x15d0 jffs2_flash_direct_writev+0xa8/0xd0 jffs2_flash_writev+0x9c9/0xef0 ? __x64_sys_setxattr+0xc4/0x160 ? do_syscall_64+0x69/0x140 ? entry_SYSCALL_64_after_hwframe+0x76/0x7e [...] Found by Linux Verification Center (linuxtesting.org) with Syzkaller.

In the Linux kernel, the following vulnerability has been resolved: tools/nolibc/stdlib: fix memory error in realloc() Pass user_p_len to memcpy() instead of heap->len to prevent realloc() from copying an extra sizeof(heap) bytes from beyond the allocated region.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix out-of-bound access of qmi_invoke_handler() Currently, there is no terminator entry for ath12k_qmi_msg_handlers hence facing below KASAN warning, ================================================================== BUG: KASAN: global-out-of-bounds in qmi_invoke_handler+0xa4/0x148 Read of size 8 at addr ffffffd00a6428d8 by task kworker/u8:2/1273 CPU: 0 PID: 1273 Comm: kworker/u8:2 Not tainted 5.4.213 #0 Workqueue: qmi_msg_handler qmi_data_ready_work Call trace: dump_backtrace+0x0/0x20c show_stack+0x14/0x1c dump_stack+0xe0/0x138 print_address_description.isra.5+0x30/0x330 __kasan_report+0x16c/0x1bc kasan_report+0xc/0x14 __asan_load8+0xa8/0xb0 qmi_invoke_handler+0xa4/0x148 qmi_handle_message+0x18c/0x1bc qmi_data_ready_work+0x4ec/0x528 process_one_work+0x2c0/0x440 worker_thread+0x324/0x4b8 kthread+0x210/0x228 ret_from_fork+0x10/0x18 The address belongs to the variable: ath12k_mac_mon_status_filter_default+0x4bd8/0xfffffffffffe2300 [ath12k] [...] ================================================================== Add a dummy terminator entry at the end to assist the qmi_invoke_handler() in traversing up to the terminator entry without accessing an out-of-boundary index. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: add error handle to avoid out-of-bounds if the sdma_v4_0_irq_id_to_seq return -EINVAL, the process should be stop to avoid out-of-bounds read, so directly return -EINVAL.

In the Linux kernel, the following vulnerability has been resolved: clk: bcm: rpi: Prevent out-of-bounds access The while loop in raspberrypi_discover_clocks() relies on the assumption that the id of the last clock element is zero. Because this data comes from the Videocore firmware and it doesn't guarantuee such a behavior this could lead to out-of-bounds access. So fix this by providing a sentinel element.

In the Linux kernel, the following vulnerability has been resolved: soundwire: cadence: fix invalid PDI offset For some reason, we add an offset to the PDI, presumably to skip the PDI0 and PDI1 which are reserved for BPT. This code is however completely wrong and leads to an out-of-bounds access. We were just lucky so far since we used only a couple of PDIs and remained within the PDI array bounds. A Fixes: tag is not provided since there are no known platforms where the out-of-bounds would be accessed, and the initial code had problems as well. A follow-up patch completely removes this useless offset.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix shift-out-of-bounds/overflow in nilfs_sb2_bad_offset() Patch series "nilfs2: fix UBSAN shift-out-of-bounds warnings on mount time". The first patch fixes a bug reported by syzbot, and the second one fixes the remaining bug of the same kind. Although they are triggered by the same super block data anomaly, I divided it into the above two because the details of the issues and how to fix it are different. Both are required to eliminate the shift-out-of-bounds issues at mount time. This patch (of 2): If the block size exponent information written in an on-disk superblock is corrupted, nilfs_sb2_bad_offset helper function can trigger shift-out-of-bounds warning followed by a kernel panic (if panic_on_warn is set): shift exponent 38983 is too large for 64-bit type 'unsigned long long' Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x1b1/0x28e lib/dump_stack.c:106 ubsan_epilogue lib/ubsan.c:151 [inline] __ubsan_handle_shift_out_of_bounds+0x33d/0x3b0 lib/ubsan.c:322 nilfs_sb2_bad_offset fs/nilfs2/the_nilfs.c:449 [inline] nilfs_load_super_block+0xdf5/0xe00 fs/nilfs2/the_nilfs.c:523 init_nilfs+0xb7/0x7d0 fs/nilfs2/the_nilfs.c:577 nilfs_fill_super+0xb1/0x5d0 fs/nilfs2/super.c:1047 nilfs_mount+0x613/0x9b0 fs/nilfs2/super.c:1317 ... In addition, since nilfs_sb2_bad_offset() performs multiplication without considering the upper bound, the computation may overflow if the disk layout parameters are not normal. This fixes these issues by inserting preliminary sanity checks for those parameters and by converting the comparison from one involving multiplication and left bit-shifting to one using division and right bit-shifting.

In the Linux kernel, the following vulnerability has been resolved: ASoC: codecs: wc938x: fix accessing array out of bounds for enum type Accessing enums using integer would result in array out of bounds access on platforms like aarch64 where sizeof(long) is 8 compared to enum size which is 4 bytes. Fix this by using enumerated items instead of integers.

In the Linux kernel, the following vulnerability has been resolved: Input: elantech - fix stack out of bound access in elantech_change_report_id() The array param[] in elantech_change_report_id() must be at least 3 bytes, because elantech_read_reg_params() is calling ps2_command() with PSMOUSE_CMD_GETINFO, that is going to access 3 bytes from param[], but it's defined in the stack as an array of 2 bytes, therefore we have a potential stack out-of-bounds access here, also confirmed by KASAN: [ 6.512374] BUG: KASAN: stack-out-of-bounds in __ps2_command+0x372/0x7e0 [ 6.512397] Read of size 1 at addr ffff8881024d77c2 by task kworker/2:1/118 [ 6.512416] CPU: 2 PID: 118 Comm: kworker/2:1 Not tainted 5.13.0-22-generic #22+arighi20211110 [ 6.512428] Hardware name: LENOVO 20T8000QGE/20T8000QGE, BIOS R1AET32W (1.08 ) 08/14/2020 [ 6.512436] Workqueue: events_long serio_handle_event [ 6.512453] Call Trace: [ 6.512462] show_stack+0x52/0x58 [ 6.512474] dump_stack+0xa1/0xd3 [ 6.512487] print_address_description.constprop.0+0x1d/0x140 [ 6.512502] ? __ps2_command+0x372/0x7e0 [ 6.512516] __kasan_report.cold+0x7d/0x112 [ 6.512527] ? _raw_write_lock_irq+0x20/0xd0 [ 6.512539] ? __ps2_command+0x372/0x7e0 [ 6.512552] kasan_report+0x3c/0x50 [ 6.512564] __asan_load1+0x6a/0x70 [ 6.512575] __ps2_command+0x372/0x7e0 [ 6.512589] ? ps2_drain+0x240/0x240 [ 6.512601] ? dev_printk_emit+0xa2/0xd3 [ 6.512612] ? dev_vprintk_emit+0xc5/0xc5 [ 6.512621] ? __kasan_check_write+0x14/0x20 [ 6.512634] ? mutex_lock+0x8f/0xe0 [ 6.512643] ? __mutex_lock_slowpath+0x20/0x20 [ 6.512655] ps2_command+0x52/0x90 [ 6.512670] elantech_ps2_command+0x4f/0xc0 [psmouse] [ 6.512734] elantech_change_report_id+0x1e6/0x256 [psmouse] [ 6.512799] ? elantech_report_trackpoint.constprop.0.cold+0xd/0xd [psmouse] [ 6.512863] ? ps2_command+0x7f/0x90 [ 6.512877] elantech_query_info.cold+0x6bd/0x9ed [psmouse] [ 6.512943] ? elantech_setup_ps2+0x460/0x460 [psmouse] [ 6.513005] ? psmouse_reset+0x69/0xb0 [psmouse] [ 6.513064] ? psmouse_attr_set_helper+0x2a0/0x2a0 [psmouse] [ 6.513122] ? phys_pmd_init+0x30e/0x521 [ 6.513137] elantech_init+0x8a/0x200 [psmouse] [ 6.513200] ? elantech_init_ps2+0xf0/0xf0 [psmouse] [ 6.513249] ? elantech_query_info+0x440/0x440 [psmouse] [ 6.513296] ? synaptics_send_cmd+0x60/0x60 [psmouse] [ 6.513342] ? elantech_query_info+0x440/0x440 [psmouse] [ 6.513388] ? psmouse_try_protocol+0x11e/0x170 [psmouse] [ 6.513432] psmouse_extensions+0x65d/0x6e0 [psmouse] [ 6.513476] ? psmouse_try_protocol+0x170/0x170 [psmouse] [ 6.513519] ? mutex_unlock+0x22/0x40 [ 6.513526] ? ps2_command+0x7f/0x90 [ 6.513536] ? psmouse_probe+0xa3/0xf0 [psmouse] [ 6.513580] psmouse_switch_protocol+0x27d/0x2e0 [psmouse] [ 6.513624] psmouse_connect+0x272/0x530 [psmouse] [ 6.513669] serio_driver_probe+0x55/0x70 [ 6.513679] really_probe+0x190/0x720 [ 6.513689] driver_probe_device+0x160/0x1f0 [ 6.513697] device_driver_attach+0x119/0x130 [ 6.513705] ? device_driver_attach+0x130/0x130 [ 6.513713] __driver_attach+0xe7/0x1a0 [ 6.513720] ? device_driver_attach+0x130/0x130 [ 6.513728] bus_for_each_dev+0xfb/0x150 [ 6.513738] ? subsys_dev_iter_exit+0x10/0x10 [ 6.513748] ? _raw_write_unlock_bh+0x30/0x30 [ 6.513757] driver_attach+0x2d/0x40 [ 6.513764] serio_handle_event+0x199/0x3d0 [ 6.513775] process_one_work+0x471/0x740 [ 6.513785] worker_thread+0x2d2/0x790 [ 6.513794] ? process_one_work+0x740/0x740 [ 6.513802] kthread+0x1b4/0x1e0 [ 6.513809] ? set_kthread_struct+0x80/0x80 [ 6.513816] ret_from_fork+0x22/0x30 [ 6.513832] The buggy address belongs to the page: [ 6.513838] page:00000000bc35e189 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1024d7 [ 6.513847] flags: 0x17ffffc0000000(node=0|zone=2|lastcpupid=0x1fffff) [ 6.513860] raw: 0 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Fix stack-out-of-bounds memory access from ioapic_write_indirect() KASAN reports the following issue: BUG: KASAN: stack-out-of-bounds in kvm_make_vcpus_request_mask+0x174/0x440 [kvm] Read of size 8 at addr ffffc9001364f638 by task qemu-kvm/4798 CPU: 0 PID: 4798 Comm: qemu-kvm Tainted: G X --------- --- Hardware name: AMD Corporation DAYTONA_X/DAYTONA_X, BIOS RYM0081C 07/13/2020 Call Trace: dump_stack+0xa5/0xe6 print_address_description.constprop.0+0x18/0x130 ? kvm_make_vcpus_request_mask+0x174/0x440 [kvm] __kasan_report.cold+0x7f/0x114 ? kvm_make_vcpus_request_mask+0x174/0x440 [kvm] kasan_report+0x38/0x50 kasan_check_range+0xf5/0x1d0 kvm_make_vcpus_request_mask+0x174/0x440 [kvm] kvm_make_scan_ioapic_request_mask+0x84/0xc0 [kvm] ? kvm_arch_exit+0x110/0x110 [kvm] ? sched_clock+0x5/0x10 ioapic_write_indirect+0x59f/0x9e0 [kvm] ? static_obj+0xc0/0xc0 ? __lock_acquired+0x1d2/0x8c0 ? kvm_ioapic_eoi_inject_work+0x120/0x120 [kvm] The problem appears to be that 'vcpu_bitmap' is allocated as a single long on stack and it should really be KVM_MAX_VCPUS long. We also seem to clear the lower 16 bits of it with bitmap_zero() for no particular reason (my guess would be that 'bitmap' and 'vcpu_bitmap' variables in kvm_bitmap_or_dest_vcpus() caused the confusion: while the later is indeed 16-bit long, the later should accommodate all possible vCPUs).

In the Linux kernel, the following vulnerability has been resolved: um: Fix out-of-bounds read in LDT setup syscall_stub_data() expects the data_count parameter to be the number of longs, not bytes. ================================================================== BUG: KASAN: stack-out-of-bounds in syscall_stub_data+0x70/0xe0 Read of size 128 at addr 000000006411f6f0 by task swapper/1 CPU: 0 PID: 1 Comm: swapper Not tainted 5.18.0+ #18 Call Trace: show_stack.cold+0x166/0x2a7 __dump_stack+0x3a/0x43 dump_stack_lvl+0x1f/0x27 print_report.cold+0xdb/0xf81 kasan_report+0x119/0x1f0 kasan_check_range+0x3a3/0x440 memcpy+0x52/0x140 syscall_stub_data+0x70/0xe0 write_ldt_entry+0xac/0x190 init_new_ldt+0x515/0x960 init_new_context+0x2c4/0x4d0 mm_init.constprop.0+0x5ed/0x760 mm_alloc+0x118/0x170 0x60033f48 do_one_initcall+0x1d7/0x860 0x60003e7b kernel_init+0x6e/0x3d4 new_thread_handler+0x1e7/0x2c0 The buggy address belongs to stack of task swapper/1 and is located at offset 64 in frame: init_new_ldt+0x0/0x960 This frame has 2 objects: [32, 40) 'addr' [64, 80) 'desc' ==================================================================

An out of bounds (OOB) memory access flaw was found in the Linux kernel in relay_file_read_start_pos in kernel/relay.c in the relayfs. This flaw could allow a local attacker to crash the system or leak kernel internal information.

In the Linux kernel, the following vulnerability has been resolved: nvme: fix memory allocation in nvme_pr_read_keys() nvme_pr_read_keys() takes num_keys from userspace and uses it to calculate the allocation size for rse via struct_size(). The upper limit is PR_KEYS_MAX (64K). A malicious or buggy userspace can pass a large num_keys value that results in a 4MB allocation attempt at most, causing a warning in the page allocator when the order exceeds MAX_PAGE_ORDER. To fix this, use kvzalloc() instead of kzalloc(). This bug has the same reasoning and fix with the patch below: https://lore.kernel.org/linux-block/20251212013510.3576091-1-kartikey406@gmail.com/ Warning log: WARNING: mm/page_alloc.c:5216 at __alloc_frozen_pages_noprof+0x5aa/0x2300 mm/page_alloc.c:5216, CPU#1: syz-executor117/272 Modules linked in: CPU: 1 UID: 0 PID: 272 Comm: syz-executor117 Not tainted 6.19.0 #1 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 RIP: 0010:__alloc_frozen_pages_noprof+0x5aa/0x2300 mm/page_alloc.c:5216 Code: ff 83 bd a8 fe ff ff 0a 0f 86 69 fb ff ff 0f b6 1d f9 f9 c4 04 80 fb 01 0f 87 3b 76 30 ff 83 e3 01 75 09 c6 05 e4 f9 c4 04 01 <0f> 0b 48 c7 85 70 fe ff ff 00 00 00 00 e9 8f fd ff ff 31 c0 e9 0d RSP: 0018:ffffc90000fcf450 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 1ffff920001f9ea0 RDX: 0000000000000000 RSI: 000000000000000b RDI: 0000000000040dc0 RBP: ffffc90000fcf648 R08: ffff88800b6c3380 R09: 0000000000000001 R10: ffffc90000fcf840 R11: ffff88807ffad280 R12: 0000000000000000 R13: 0000000000040dc0 R14: 0000000000000001 R15: ffffc90000fcf620 FS: 0000555565db33c0(0000) GS:ffff8880be26c000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000002000000c CR3: 0000000003b72000 CR4: 00000000000006f0 Call Trace: <TASK> alloc_pages_mpol+0x236/0x4d0 mm/mempolicy.c:2486 alloc_frozen_pages_noprof+0x149/0x180 mm/mempolicy.c:2557 ___kmalloc_large_node+0x10c/0x140 mm/slub.c:5598 __kmalloc_large_node_noprof+0x25/0xc0 mm/slub.c:5629 __do_kmalloc_node mm/slub.c:5645 [inline] __kmalloc_noprof+0x483/0x6f0 mm/slub.c:5669 kmalloc_noprof include/linux/slab.h:961 [inline] kzalloc_noprof include/linux/slab.h:1094 [inline] nvme_pr_read_keys+0x8f/0x4c0 drivers/nvme/host/pr.c:245 blkdev_pr_read_keys block/ioctl.c:456 [inline] blkdev_common_ioctl+0x1b71/0x29b0 block/ioctl.c:730 blkdev_ioctl+0x299/0x700 block/ioctl.c:786 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:597 [inline] __se_sys_ioctl fs/ioctl.c:583 [inline] __x64_sys_ioctl+0x1bf/0x220 fs/ioctl.c:583 x64_sys_call+0x1280/0x21b0 mnt/fuzznvme_1/fuzznvme/linux-build/v6.19/./arch/x86/include/generated/asm/syscalls_64.h:17 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0x71/0x330 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7fb893d3108d Code: 28 c3 e8 46 1e 00 00 66 0f 1f 44 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffff61f2f38 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007ffff61f3138 RCX: 00007fb893d3108d RDX: 0000000020000040 RSI: 00000000c01070ce RDI: 0000000000000003 RBP: 0000000000000001 R08: 0000000000000000 R09: 00007ffff61f3138 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000001 R13: 00007ffff61f3128 R14: 00007fb893dae530 R15: 0000000000000001 </TASK>

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Use correct version for UAC3 header validation The entry of the validators table for UAC3 AC header descriptor is defined with the wrong protocol version UAC_VERSION_2, while it should have been UAC_VERSION_3. This results in the validator never matching for actual UAC3 devices (protocol == UAC_VERSION_3), causing their header descriptors to bypass validation entirely. A malicious USB device presenting a truncated UAC3 header could exploit this to cause out-of-bounds reads when the driver later accesses unvalidated descriptor fields. The bug was introduced in the same commit as the recently fixed UAC3 feature unit sub-type typo, and appears to be from the same copy-paste error when the UAC3 section was created from the UAC2 section.

In the Linux kernel, the following vulnerability has been resolved: scsi: bfa: Ensure the copied buf is NUL terminated Currently, we allocate a nbytes-sized kernel buffer and copy nbytes from userspace to that buffer. Later, we use sscanf on this buffer but we don't ensure that the string is terminated inside the buffer, this can lead to OOB read when using sscanf. Fix this issue by using memdup_user_nul instead of memdup_user.

In the Linux kernel, the following vulnerability has been resolved: bonding: limit BOND_MODE_8023AD to Ethernet devices BOND_MODE_8023AD makes sense for ARPHRD_ETHER only. syzbot reported: BUG: KASAN: global-out-of-bounds in __hw_addr_create net/core/dev_addr_lists.c:63 [inline] BUG: KASAN: global-out-of-bounds in __hw_addr_add_ex+0x25d/0x760 net/core/dev_addr_lists.c:118 Read of size 16 at addr ffffffff8bf94040 by task syz.1.3580/19497 CPU: 1 UID: 0 PID: 19497 Comm: syz.1.3580 Tainted: G L syzkaller #0 PREEMPT(full) Tainted: [L]=SOFTLOCKUP Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025 Call Trace: <TASK> dump_stack_lvl+0xe8/0x150 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xca/0x240 mm/kasan/report.c:482 kasan_report+0x118/0x150 mm/kasan/report.c:595 check_region_inline mm/kasan/generic.c:-1 [inline] kasan_check_range+0x2b0/0x2c0 mm/kasan/generic.c:200 __asan_memcpy+0x29/0x70 mm/kasan/shadow.c:105 __hw_addr_create net/core/dev_addr_lists.c:63 [inline] __hw_addr_add_ex+0x25d/0x760 net/core/dev_addr_lists.c:118 __dev_mc_add net/core/dev_addr_lists.c:868 [inline] dev_mc_add+0xa1/0x120 net/core/dev_addr_lists.c:886 bond_enslave+0x2b8b/0x3ac0 drivers/net/bonding/bond_main.c:2180 do_set_master+0x533/0x6d0 net/core/rtnetlink.c:2963 do_setlink+0xcf0/0x41c0 net/core/rtnetlink.c:3165 rtnl_changelink net/core/rtnetlink.c:3776 [inline] __rtnl_newlink net/core/rtnetlink.c:3935 [inline] rtnl_newlink+0x161c/0x1c90 net/core/rtnetlink.c:4072 rtnetlink_rcv_msg+0x7cf/0xb70 net/core/rtnetlink.c:6958 netlink_rcv_skb+0x208/0x470 net/netlink/af_netlink.c:2550 netlink_unicast_kernel net/netlink/af_netlink.c:1318 [inline] netlink_unicast+0x82f/0x9e0 net/netlink/af_netlink.c:1344 netlink_sendmsg+0x805/0xb30 net/netlink/af_netlink.c:1894 sock_sendmsg_nosec net/socket.c:727 [inline] __sock_sendmsg+0x21c/0x270 net/socket.c:742 ____sys_sendmsg+0x505/0x820 net/socket.c:2592 ___sys_sendmsg+0x21f/0x2a0 net/socket.c:2646 __sys_sendmsg+0x164/0x220 net/socket.c:2678 do_syscall_32_irqs_on arch/x86/entry/syscall_32.c:83 [inline] __do_fast_syscall_32+0x1dc/0x560 arch/x86/entry/syscall_32.c:307 do_fast_syscall_32+0x34/0x80 arch/x86/entry/syscall_32.c:332 entry_SYSENTER_compat_after_hwframe+0x84/0x8e </TASK> The buggy address belongs to the variable: lacpdu_mcast_addr+0x0/0x40

In the Linux kernel, the following vulnerability has been resolved: crypto: qat - validate slices count returned by FW The function adf_send_admin_tl_start() enables the telemetry (TL) feature on a QAT device by sending the ICP_QAT_FW_TL_START message to the firmware. This triggers the FW to start writing TL data to a DMA buffer in memory and returns an array containing the number of accelerators of each type (slices) supported by this HW. The pointer to this array is stored in the adf_tl_hw_data data structure called slice_cnt. The array slice_cnt is then used in the function tl_print_dev_data() to report in debugfs only statistics about the supported accelerators. An incorrect value of the elements in slice_cnt might lead to an out of bounds memory read. At the moment, there isn't an implementation of FW that returns a wrong value, but for robustness validate the slice count array returned by FW.

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: smm: number of GPRs in the SMRAM image depends on the image format On 64 bit host, if the guest doesn't have X86_FEATURE_LM, KVM will access 16 gprs to 32-bit smram image, causing out-ouf-bound ram access. On 32 bit host, the rsm_load_state_64/enter_smm_save_state_64 is compiled out, thus access overflow can't happen.

In the Linux kernel, the following vulnerability has been resolved: dlm: fix plock invalid read This patch fixes an invalid read showed by KASAN. A unlock will allocate a "struct plock_op" and a followed send_op() will append it to a global send_list data structure. In some cases a followed dev_read() moves it to recv_list and dev_write() will cast it to "struct plock_xop" and access fields which are only available in those structures. At this point an invalid read happens by accessing those fields. To fix this issue the "callback" field is moved to "struct plock_op" to indicate that a cast to "plock_xop" is allowed and does the additional "plock_xop" handling if set. Example of the KASAN output which showed the invalid read: [ 2064.296453] ================================================================== [ 2064.304852] BUG: KASAN: slab-out-of-bounds in dev_write+0x52b/0x5a0 [dlm] [ 2064.306491] Read of size 8 at addr ffff88800ef227d8 by task dlm_controld/7484 [ 2064.308168] [ 2064.308575] CPU: 0 PID: 7484 Comm: dlm_controld Kdump: loaded Not tainted 5.14.0+ #9 [ 2064.310292] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 [ 2064.311618] Call Trace: [ 2064.312218] dump_stack_lvl+0x56/0x7b [ 2064.313150] print_address_description.constprop.8+0x21/0x150 [ 2064.314578] ? dev_write+0x52b/0x5a0 [dlm] [ 2064.315610] ? dev_write+0x52b/0x5a0 [dlm] [ 2064.316595] kasan_report.cold.14+0x7f/0x11b [ 2064.317674] ? dev_write+0x52b/0x5a0 [dlm] [ 2064.318687] dev_write+0x52b/0x5a0 [dlm] [ 2064.319629] ? dev_read+0x4a0/0x4a0 [dlm] [ 2064.320713] ? bpf_lsm_kernfs_init_security+0x10/0x10 [ 2064.321926] vfs_write+0x17e/0x930 [ 2064.322769] ? __fget_light+0x1aa/0x220 [ 2064.323753] ksys_write+0xf1/0x1c0 [ 2064.324548] ? __ia32_sys_read+0xb0/0xb0 [ 2064.325464] do_syscall_64+0x3a/0x80 [ 2064.326387] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 2064.327606] RIP: 0033:0x7f807e4ba96f [ 2064.328470] Code: 89 54 24 18 48 89 74 24 10 89 7c 24 08 e8 39 87 f8 ff 48 8b 54 24 18 48 8b 74 24 10 41 89 c0 8b 7c 24 08 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 31 44 89 c7 48 89 44 24 08 e8 7c 87 f8 ff 48 [ 2064.332902] RSP: 002b:00007ffd50cfe6e0 EFLAGS: 00000293 ORIG_RAX: 0000000000000001 [ 2064.334658] RAX: ffffffffffffffda RBX: 000055cc3886eb30 RCX: 00007f807e4ba96f [ 2064.336275] RDX: 0000000000000040 RSI: 00007ffd50cfe7e0 RDI: 0000000000000010 [ 2064.337980] RBP: 00007ffd50cfe7e0 R08: 0000000000000000 R09: 0000000000000001 [ 2064.339560] R10: 000055cc3886eb30 R11: 0000000000000293 R12: 000055cc3886eb80 [ 2064.341237] R13: 000055cc3886eb00 R14: 000055cc3886f590 R15: 0000000000000001 [ 2064.342857] [ 2064.343226] Allocated by task 12438: [ 2064.344057] kasan_save_stack+0x1c/0x40 [ 2064.345079] __kasan_kmalloc+0x84/0xa0 [ 2064.345933] kmem_cache_alloc_trace+0x13b/0x220 [ 2064.346953] dlm_posix_unlock+0xec/0x720 [dlm] [ 2064.348811] do_lock_file_wait.part.32+0xca/0x1d0 [ 2064.351070] fcntl_setlk+0x281/0xbc0 [ 2064.352879] do_fcntl+0x5e4/0xfe0 [ 2064.354657] __x64_sys_fcntl+0x11f/0x170 [ 2064.356550] do_syscall_64+0x3a/0x80 [ 2064.358259] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 2064.360745] [ 2064.361511] Last potentially related work creation: [ 2064.363957] kasan_save_stack+0x1c/0x40 [ 2064.365811] __kasan_record_aux_stack+0xaf/0xc0 [ 2064.368100] call_rcu+0x11b/0xf70 [ 2064.369785] dlm_process_incoming_buffer+0x47d/0xfd0 [dlm] [ 2064.372404] receive_from_sock+0x290/0x770 [dlm] [ 2064.374607] process_recv_sockets+0x32/0x40 [dlm] [ 2064.377290] process_one_work+0x9a8/0x16e0 [ 2064.379357] worker_thread+0x87/0xbf0 [ 2064.381188] kthread+0x3ac/0x490 [ 2064.383460] ret_from_fork+0x22/0x30 [ 2064.385588] [ 2064.386518] Second to last potentially related work creation: [ 2064.389219] kasan_save_stack+0x1c/0x40 [ 2064.391043] __kasan_record_aux_stack+0xaf/0xc0 [ 2064.393303] call_rcu+0x11b/0xf70 [ 2064.394885] dlm_process_incoming_buffer+0x47d/0xfd0 [dlm] [ 2064.397694] receive_from_sock+0x290/0x770 ---truncated---

In the Linux kernel 6.0.8, there is an out-of-bounds read in ntfs_attr_find in fs/ntfs/attrib.c.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Fix for out-of bound access error Selfgen stats are placed in a buffer using print_array_to_buf_index() function. Array length parameter passed to the function is too big, resulting in possible out-of bound memory error. Decreasing buffer size by one fixes faulty upper bound of passed array. Discovered in coverity scan, CID 1600742 and CID 1600758

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmsmac: add gain range check to wlc_phy_iqcal_gainparams_nphy() In 'wlc_phy_iqcal_gainparams_nphy()', add gain range check to WARN() instead of possible out-of-bounds 'tbl_iqcal_gainparams_nphy' access. Compile tested only. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: crypto: qat/qat_4xxx - fix off by one in uof_get_name() The fw_objs[] array has "num_objs" elements so the > needs to be >= to prevent an out of bounds read.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Fix out of bounds reads when finding clock sources The current USB-audio driver code doesn't check bLength of each descriptor at traversing for clock descriptors. That is, when a device provides a bogus descriptor with a shorter bLength, the driver might hit out-of-bounds reads. For addressing it, this patch adds sanity checks to the validator functions for the clock descriptor traversal. When the descriptor length is shorter than expected, it's skipped in the loop. For the clock source and clock multiplier descriptors, we can just check bLength against the sizeof() of each descriptor type. OTOH, the clock selector descriptor of UAC2 and UAC3 has an array of bNrInPins elements and two more fields at its tail, hence those have to be checked in addition to the sizeof() check.

In the Linux kernel, the following vulnerability has been resolved: security/keys: fix slab-out-of-bounds in key_task_permission KASAN reports an out of bounds read: BUG: KASAN: slab-out-of-bounds in __kuid_val include/linux/uidgid.h:36 BUG: KASAN: slab-out-of-bounds in uid_eq include/linux/uidgid.h:63 [inline] BUG: KASAN: slab-out-of-bounds in key_task_permission+0x394/0x410 security/keys/permission.c:54 Read of size 4 at addr ffff88813c3ab618 by task stress-ng/4362 CPU: 2 PID: 4362 Comm: stress-ng Not tainted 5.10.0-14930-gafbffd6c3ede #15 Call Trace: __dump_stack lib/dump_stack.c:82 [inline] dump_stack+0x107/0x167 lib/dump_stack.c:123 print_address_description.constprop.0+0x19/0x170 mm/kasan/report.c:400 __kasan_report.cold+0x6c/0x84 mm/kasan/report.c:560 kasan_report+0x3a/0x50 mm/kasan/report.c:585 __kuid_val include/linux/uidgid.h:36 [inline] uid_eq include/linux/uidgid.h:63 [inline] key_task_permission+0x394/0x410 security/keys/permission.c:54 search_nested_keyrings+0x90e/0xe90 security/keys/keyring.c:793 This issue was also reported by syzbot. It can be reproduced by following these steps(more details [1]): 1. Obtain more than 32 inputs that have similar hashes, which ends with the pattern '0xxxxxxxe6'. 2. Reboot and add the keys obtained in step 1. The reproducer demonstrates how this issue happened: 1. In the search_nested_keyrings function, when it iterates through the slots in a node(below tag ascend_to_node), if the slot pointer is meta and node->back_pointer != NULL(it means a root), it will proceed to descend_to_node. However, there is an exception. If node is the root, and one of the slots points to a shortcut, it will be treated as a keyring. 2. Whether the ptr is keyring decided by keyring_ptr_is_keyring function. However, KEYRING_PTR_SUBTYPE is 0x2UL, the same as ASSOC_ARRAY_PTR_SUBTYPE_MASK. 3. When 32 keys with the similar hashes are added to the tree, the ROOT has keys with hashes that are not similar (e.g. slot 0) and it splits NODE A without using a shortcut. When NODE A is filled with keys that all hashes are xxe6, the keys are similar, NODE A will split with a shortcut. Finally, it forms the tree as shown below, where slot 6 points to a shortcut. NODE A +------>+---+ ROOT | | 0 | xxe6 +---+ | +---+ xxxx | 0 | shortcut : : xxe6 +---+ | +---+ xxe6 : : | | | xxe6 +---+ | +---+ | 6 |---+ : : xxe6 +---+ +---+ xxe6 : : | f | xxe6 +---+ +---+ xxe6 | f | +---+ 4. As mentioned above, If a slot(slot 6) of the root points to a shortcut, it may be mistakenly transferred to a key*, leading to a read out-of-bounds read. To fix this issue, one should jump to descend_to_node if the ptr is a shortcut, regardless of whether the node is root or not. [1] https://lore.kernel.org/linux-kernel/1cfa878e-8c7b-4570-8606-21daf5e13ce7@huaweicloud.com/ [jarkko: tweaked the commit message a bit to have an appropriate closes tag.]

In the Linux kernel, the following vulnerability has been resolved: sch_cake: Fix out of bounds when parsing TCP options and header The TCP option parser in cake qdisc (cake_get_tcpopt and cake_tcph_may_drop) could read one byte out of bounds. When the length is 1, the execution flow gets into the loop, reads one byte of the opcode, and if the opcode is neither TCPOPT_EOL nor TCPOPT_NOP, it reads one more byte, which exceeds the length of 1. This fix is inspired by commit 9609dad263f8 ("ipv4: tcp_input: fix stack out of bounds when parsing TCP options."). v2 changes: Added doff validation in cake_get_tcphdr to avoid parsing garbage as TCP header. Although it wasn't strictly an out-of-bounds access (memory was allocated), garbage values could be read where CAKE expected the TCP header if doff was smaller than 5.

In the Linux kernel, the following vulnerability has been resolved: dm cache: fix out-of-bounds access to the dirty bitset when resizing dm-cache checks the dirty bits of the cache blocks to be dropped when shrinking the fast device, but an index bug in bitset iteration causes out-of-bounds access. Reproduce steps: 1. create a cache device of 1024 cache blocks (128 bytes dirty bitset) dmsetup create cmeta --table "0 8192 linear /dev/sdc 0" dmsetup create cdata --table "0 131072 linear /dev/sdc 8192" dmsetup create corig --table "0 524288 linear /dev/sdc 262144" dd if=/dev/zero of=/dev/mapper/cmeta bs=4k count=1 oflag=direct dmsetup create cache --table "0 524288 cache /dev/mapper/cmeta \ /dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0" 2. shrink the fast device to 512 cache blocks, triggering out-of-bounds access to the dirty bitset (offset 0x80) dmsetup suspend cache dmsetup reload cdata --table "0 65536 linear /dev/sdc 8192" dmsetup resume cdata dmsetup resume cache KASAN reports: BUG: KASAN: vmalloc-out-of-bounds in cache_preresume+0x269/0x7b0 Read of size 8 at addr ffffc900000f3080 by task dmsetup/131 (...snip...) The buggy address belongs to the virtual mapping at [ffffc900000f3000, ffffc900000f5000) created by: cache_ctr+0x176a/0x35f0 (...snip...) Memory state around the buggy address: ffffc900000f2f80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ffffc900000f3000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffffc900000f3080: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ^ ffffc900000f3100: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ffffc900000f3180: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 Fix by making the index post-incremented.

A slab-out-of-bound read problem was found in brcmf_get_assoc_ies in drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c in the Linux Kernel. This issue could occur when assoc_info->req_len data is bigger than the size of the buffer, defined as WL_EXTRA_BUF_MAX, leading to a denial of service.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt76x0: fix oob access in mt76x0_phy_get_target_power After 'commit ba45841ca5eb ("wifi: mt76: mt76x02: simplify struct mt76x02_rate_power")', mt76x02 relies on ht[0-7] rate_power data for vht mcs{0,7}, while it uses vth[0-1] rate_power for vht mcs {8,9}. Fix a possible out-of-bound access in mt76x0_phy_get_target_power routine.

In the Linux kernel, the following vulnerability has been resolved: bpf: Propagate error from htab_lock_bucket() to userspace In __htab_map_lookup_and_delete_batch() if htab_lock_bucket() returns -EBUSY, it will go to next bucket. Going to next bucket may not only skip the elements in current bucket silently, but also incur out-of-bound memory access or expose kernel memory to userspace if current bucket_cnt is greater than bucket_size or zero. Fixing it by stopping batch operation and returning -EBUSY when htab_lock_bucket() fails, and the application can retry or skip the busy batch as needed.

In the Linux kernel, the following vulnerability has been resolved: binfmt_misc: fix shift-out-of-bounds in check_special_flags UBSAN reported a shift-out-of-bounds warning: left shift of 1 by 31 places cannot be represented in type 'int' Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x8d/0xcf lib/dump_stack.c:106 ubsan_epilogue+0xa/0x44 lib/ubsan.c:151 __ubsan_handle_shift_out_of_bounds+0x1e7/0x208 lib/ubsan.c:322 check_special_flags fs/binfmt_misc.c:241 [inline] create_entry fs/binfmt_misc.c:456 [inline] bm_register_write+0x9d3/0xa20 fs/binfmt_misc.c:654 vfs_write+0x11e/0x580 fs/read_write.c:582 ksys_write+0xcf/0x120 fs/read_write.c:637 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x34/0x80 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x4194e1 Since the type of Node's flags is unsigned long, we should define these macros with same type too.

NVIDIA GPU Display Driver for Linux contains a vulnerability in a kernel mode layer handler, which may lead to denial of service or information disclosure.

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Fix potential shift-out-of-bounds in brcmf_fw_alloc_request() This patch fixes a shift-out-of-bounds in brcmfmac that occurs in BIT(chiprev) when a 'chiprev' provided by the device is too large. It should also not be equal to or greater than BITS_PER_TYPE(u32) as we do bitwise AND with a u32 variable and BIT(chiprev). The patch adds a check that makes the function return NULL if that is the case. Note that the NULL case is later handled by the bus-specific caller, brcmf_usb_probe_cb() or brcmf_usb_reset_resume(), for example. Found by a modified version of syzkaller. UBSAN: shift-out-of-bounds in drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c shift exponent 151055786 is too large for 64-bit type 'long unsigned int' CPU: 0 PID: 1885 Comm: kworker/0:2 Tainted: G O 5.14.0+ #132 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Workqueue: usb_hub_wq hub_event Call Trace: dump_stack_lvl+0x57/0x7d ubsan_epilogue+0x5/0x40 __ubsan_handle_shift_out_of_bounds.cold+0x53/0xdb ? lock_chain_count+0x20/0x20 brcmf_fw_alloc_request.cold+0x19/0x3ea ? brcmf_fw_get_firmwares+0x250/0x250 ? brcmf_usb_ioctl_resp_wait+0x1a7/0x1f0 brcmf_usb_get_fwname+0x114/0x1a0 ? brcmf_usb_reset_resume+0x120/0x120 ? number+0x6c4/0x9a0 brcmf_c_process_clm_blob+0x168/0x590 ? put_dec+0x90/0x90 ? enable_ptr_key_workfn+0x20/0x20 ? brcmf_common_pd_remove+0x50/0x50 ? rcu_read_lock_sched_held+0xa1/0xd0 brcmf_c_preinit_dcmds+0x673/0xc40 ? brcmf_c_set_joinpref_default+0x100/0x100 ? rcu_read_lock_sched_held+0xa1/0xd0 ? rcu_read_lock_bh_held+0xb0/0xb0 ? lock_acquire+0x19d/0x4e0 ? find_held_lock+0x2d/0x110 ? brcmf_usb_deq+0x1cc/0x260 ? mark_held_locks+0x9f/0xe0 ? lockdep_hardirqs_on_prepare+0x273/0x3e0 ? _raw_spin_unlock_irqrestore+0x47/0x50 ? trace_hardirqs_on+0x1c/0x120 ? brcmf_usb_deq+0x1a7/0x260 ? brcmf_usb_rx_fill_all+0x5a/0xf0 brcmf_attach+0x246/0xd40 ? wiphy_new_nm+0x1476/0x1d50 ? kmemdup+0x30/0x40 brcmf_usb_probe+0x12de/0x1690 ? brcmf_usbdev_qinit.constprop.0+0x470/0x470 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 ? usb_match_id.part.0+0x88/0xc0 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 ? driver_allows_async_probing+0x120/0x120 bus_for_each_drv+0x123/0x1a0 ? bus_rescan_devices+0x20/0x20 ? lockdep_hardirqs_on_prepare+0x273/0x3e0 ? trace_hardirqs_on+0x1c/0x120 __device_attach+0x207/0x330 ? device_bind_driver+0xb0/0xb0 ? kobject_uevent_env+0x230/0x12c0 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 ? __mutex_unlock_slowpath+0xe7/0x660 ? __fw_devlink_link_to_suppliers+0x550/0x550 usb_set_configuration+0x984/0x1770 ? kernfs_create_link+0x175/0x230 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 ? driver_allows_async_probing+0x120/0x120 bus_for_each_drv+0x123/0x1a0 ? bus_rescan_devices+0x20/0x20 ? lockdep_hardirqs_on_prepare+0x273/0x3e0 ? trace_hardirqs_on+0x1c/0x120 __device_attach+0x207/0x330 ? device_bind_driver+0xb0/0xb0 ? kobject_uevent_env+0x230/0x12c0 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 ? __fw_devlink_link_to_suppliers+0x550/0x550 usb_new_device.cold+0x463/0xf66 ? hub_disconnect+0x400/0x400 ? _raw_spin_unlock_irq+0x24/0x30 hub_event+0x10d5/0x3330 ? hub_port_debounce+0x280/0x280 ? __lock_acquire+0x1671/0x5790 ? wq_calc_node_cpumask+0x170/0x2a0 ? lock_release+0x640/0x640 ? rcu_read_lock_sched_held+0xa1/0xd0 ? rcu_read_lock_bh_held+0xb0/0xb0 ? lockdep_hardirqs_on_prepare+0x273/0x3e0 process_one_work+0x873/0x13e0 ? lock_release+0x640/0x640 ? pwq_dec_nr_in_flight+0x320/0x320 ? rwlock_bug.part.0+0x90/0x90 worker_thread+0x8b/0xd10 ? __kthread_parkme+0xd9/0x1d0 ? pr ---truncated---

In the Linux kernel, the following vulnerability has been resolved: zonefs: fix zonefs_iomap_begin() for reads If a readahead is issued to a sequential zone file with an offset exactly equal to the current file size, the iomap type is set to IOMAP_UNWRITTEN, which will prevent an IO, but the iomap length is calculated as 0. This causes a WARN_ON() in iomap_iter(): [17309.548939] WARNING: CPU: 3 PID: 2137 at fs/iomap/iter.c:34 iomap_iter+0x9cf/0xe80 [...] [17309.650907] RIP: 0010:iomap_iter+0x9cf/0xe80 [...] [17309.754560] Call Trace: [17309.757078] <TASK> [17309.759240] ? lock_is_held_type+0xd8/0x130 [17309.763531] iomap_readahead+0x1a8/0x870 [17309.767550] ? iomap_read_folio+0x4c0/0x4c0 [17309.771817] ? lockdep_hardirqs_on_prepare+0x400/0x400 [17309.778848] ? lock_release+0x370/0x750 [17309.784462] ? folio_add_lru+0x217/0x3f0 [17309.790220] ? reacquire_held_locks+0x4e0/0x4e0 [17309.796543] read_pages+0x17d/0xb60 [17309.801854] ? folio_add_lru+0x238/0x3f0 [17309.807573] ? readahead_expand+0x5f0/0x5f0 [17309.813554] ? policy_node+0xb5/0x140 [17309.819018] page_cache_ra_unbounded+0x27d/0x450 [17309.825439] filemap_get_pages+0x500/0x1450 [17309.831444] ? filemap_add_folio+0x140/0x140 [17309.837519] ? lock_is_held_type+0xd8/0x130 [17309.843509] filemap_read+0x28c/0x9f0 [17309.848953] ? zonefs_file_read_iter+0x1ea/0x4d0 [zonefs] [17309.856162] ? trace_contention_end+0xd6/0x130 [17309.862416] ? __mutex_lock+0x221/0x1480 [17309.868151] ? zonefs_file_read_iter+0x166/0x4d0 [zonefs] [17309.875364] ? filemap_get_pages+0x1450/0x1450 [17309.881647] ? __mutex_unlock_slowpath+0x15e/0x620 [17309.888248] ? wait_for_completion_io_timeout+0x20/0x20 [17309.895231] ? lock_is_held_type+0xd8/0x130 [17309.901115] ? lock_is_held_type+0xd8/0x130 [17309.906934] zonefs_file_read_iter+0x356/0x4d0 [zonefs] [17309.913750] new_sync_read+0x2d8/0x520 [17309.919035] ? __x64_sys_lseek+0x1d0/0x1d0 Furthermore, this causes iomap_readahead() to loop forever as iomap_readahead_iter() always returns 0, making no progress. Fix this by treating reads after the file size as access to holes, setting the iomap type to IOMAP_HOLE, the iomap addr to IOMAP_NULL_ADDR and using the length argument as is for the iomap length. To simplify the code with this change, zonefs_iomap_begin() is split into the read variant, zonefs_read_iomap_begin() and zonefs_read_iomap_ops, and the write variant, zonefs_write_iomap_begin() and zonefs_write_iomap_ops.

In the Linux kernel, the following vulnerability has been resolved: dm raid: fix address sanitizer warning in raid_status There is this warning when using a kernel with the address sanitizer and running this testsuite: https://gitlab.com/cki-project/kernel-tests/-/tree/main/storage/swraid/scsi_raid ================================================================== BUG: KASAN: slab-out-of-bounds in raid_status+0x1747/0x2820 [dm_raid] Read of size 4 at addr ffff888079d2c7e8 by task lvcreate/13319 CPU: 0 PID: 13319 Comm: lvcreate Not tainted 5.18.0-0.rc3.<snip> #1 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 Call Trace: <TASK> dump_stack_lvl+0x6a/0x9c print_address_description.constprop.0+0x1f/0x1e0 print_report.cold+0x55/0x244 kasan_report+0xc9/0x100 raid_status+0x1747/0x2820 [dm_raid] dm_ima_measure_on_table_load+0x4b8/0xca0 [dm_mod] table_load+0x35c/0x630 [dm_mod] ctl_ioctl+0x411/0x630 [dm_mod] dm_ctl_ioctl+0xa/0x10 [dm_mod] __x64_sys_ioctl+0x12a/0x1a0 do_syscall_64+0x5b/0x80 The warning is caused by reading conf->max_nr_stripes in raid_status. The code in raid_status reads mddev->private, casts it to struct r5conf and reads the entry max_nr_stripes. However, if we have different raid type than 4/5/6, mddev->private doesn't point to struct r5conf; it may point to struct r0conf, struct r1conf, struct r10conf or struct mpconf. If we cast a pointer to one of these structs to struct r5conf, we will be reading invalid memory and KASAN warns about it. Fix this bug by reading struct r5conf only if raid type is 4, 5 or 6.

In the Linux kernel, the following vulnerability has been resolved: bpf: Do mark_chain_precision for ARG_CONST_ALLOC_SIZE_OR_ZERO Precision markers need to be propagated whenever we have an ARG_CONST_* style argument, as the verifier cannot consider imprecise scalars to be equivalent for the purposes of states_equal check when such arguments refine the return value (in this case, set mem_size for PTR_TO_MEM). The resultant mem_size for the R0 is derived from the constant value, and if the verifier incorrectly prunes states considering them equivalent where such arguments exist (by seeing that both registers have reg->precise as false in regsafe), we can end up with invalid programs passing the verifier which can do access beyond what should have been the correct mem_size in that explored state. To show a concrete example of the problem: 0000000000000000 <prog>: 0: r2 = *(u32 *)(r1 + 80) 1: r1 = *(u32 *)(r1 + 76) 2: r3 = r1 3: r3 += 4 4: if r3 > r2 goto +18 <LBB5_5> 5: w2 = 0 6: *(u32 *)(r1 + 0) = r2 7: r1 = *(u32 *)(r1 + 0) 8: r2 = 1 9: if w1 == 0 goto +1 <LBB5_3> 10: r2 = -1 0000000000000058 <LBB5_3>: 11: r1 = 0 ll 13: r3 = 0 14: call bpf_ringbuf_reserve 15: if r0 == 0 goto +7 <LBB5_5> 16: r1 = r0 17: r1 += 16777215 18: w2 = 0 19: *(u8 *)(r1 + 0) = r2 20: r1 = r0 21: r2 = 0 22: call bpf_ringbuf_submit 00000000000000b8 <LBB5_5>: 23: w0 = 0 24: exit For the first case, the single line execution's exploration will prune the search at insn 14 for the branch insn 9's second leg as it will be verified first using r2 = -1 (UINT_MAX), while as w1 at insn 9 will always be 0 so at runtime we don't get error for being greater than UINT_MAX/4 from bpf_ringbuf_reserve. The verifier during regsafe just sees reg->precise as false for both r2 registers in both states, hence considers them equal for purposes of states_equal. If we propagated precise markers using the backtracking support, we would use the precise marking to then ensure that old r2 (UINT_MAX) was within the new r2 (1) and this would never be true, so the verification would rightfully fail. The end result is that the out of bounds access at instruction 19 would be permitted without this fix. Note that reg->precise is always set to true when user does not have CAP_BPF (or when subprog count is greater than 1 (i.e. use of any static or global functions)), hence this is only a problem when precision marks need to be explicitly propagated (i.e. privileged users with CAP_BPF). A simplified test case has been included in the next patch to prevent future regressions.

In the Linux kernel, the following vulnerability has been resolved: md-raid10: fix KASAN warning There's a KASAN warning in raid10_remove_disk when running the lvm test lvconvert-raid-reshape.sh. We fix this warning by verifying that the value "number" is valid. BUG: KASAN: slab-out-of-bounds in raid10_remove_disk+0x61/0x2a0 [raid10] Read of size 8 at addr ffff889108f3d300 by task mdX_raid10/124682 CPU: 3 PID: 124682 Comm: mdX_raid10 Not tainted 5.19.0-rc6 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x34/0x44 print_report.cold+0x45/0x57a ? __lock_text_start+0x18/0x18 ? raid10_remove_disk+0x61/0x2a0 [raid10] kasan_report+0xa8/0xe0 ? raid10_remove_disk+0x61/0x2a0 [raid10] raid10_remove_disk+0x61/0x2a0 [raid10] Buffer I/O error on dev dm-76, logical block 15344, async page read ? __mutex_unlock_slowpath.constprop.0+0x1e0/0x1e0 remove_and_add_spares+0x367/0x8a0 [md_mod] ? super_written+0x1c0/0x1c0 [md_mod] ? mutex_trylock+0xac/0x120 ? _raw_spin_lock+0x72/0xc0 ? _raw_spin_lock_bh+0xc0/0xc0 md_check_recovery+0x848/0x960 [md_mod] raid10d+0xcf/0x3360 [raid10] ? sched_clock_cpu+0x185/0x1a0 ? rb_erase+0x4d4/0x620 ? var_wake_function+0xe0/0xe0 ? psi_group_change+0x411/0x500 ? preempt_count_sub+0xf/0xc0 ? _raw_spin_lock_irqsave+0x78/0xc0 ? __lock_text_start+0x18/0x18 ? raid10_sync_request+0x36c0/0x36c0 [raid10] ? preempt_count_sub+0xf/0xc0 ? _raw_spin_unlock_irqrestore+0x19/0x40 ? del_timer_sync+0xa9/0x100 ? try_to_del_timer_sync+0xc0/0xc0 ? _raw_spin_lock_irqsave+0x78/0xc0 ? __lock_text_start+0x18/0x18 ? _raw_spin_unlock_irq+0x11/0x24 ? __list_del_entry_valid+0x68/0xa0 ? finish_wait+0xa3/0x100 md_thread+0x161/0x260 [md_mod] ? unregister_md_personality+0xa0/0xa0 [md_mod] ? _raw_spin_lock_irqsave+0x78/0xc0 ? prepare_to_wait_event+0x2c0/0x2c0 ? unregister_md_personality+0xa0/0xa0 [md_mod] kthread+0x148/0x180 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x1f/0x30 </TASK> Allocated by task 124495: kasan_save_stack+0x1e/0x40 __kasan_kmalloc+0x80/0xa0 setup_conf+0x140/0x5c0 [raid10] raid10_run+0x4cd/0x740 [raid10] md_run+0x6f9/0x1300 [md_mod] raid_ctr+0x2531/0x4ac0 [dm_raid] dm_table_add_target+0x2b0/0x620 [dm_mod] table_load+0x1c8/0x400 [dm_mod] ctl_ioctl+0x29e/0x560 [dm_mod] dm_compat_ctl_ioctl+0x7/0x20 [dm_mod] __do_compat_sys_ioctl+0xfa/0x160 do_syscall_64+0x90/0xc0 entry_SYSCALL_64_after_hwframe+0x46/0xb0 Last potentially related work creation: kasan_save_stack+0x1e/0x40 __kasan_record_aux_stack+0x9e/0xc0 kvfree_call_rcu+0x84/0x480 timerfd_release+0x82/0x140 L __fput+0xfa/0x400 task_work_run+0x80/0xc0 exit_to_user_mode_prepare+0x155/0x160 syscall_exit_to_user_mode+0x12/0x40 do_syscall_64+0x42/0xc0 entry_SYSCALL_64_after_hwframe+0x46/0xb0 Second to last potentially related work creation: kasan_save_stack+0x1e/0x40 __kasan_record_aux_stack+0x9e/0xc0 kvfree_call_rcu+0x84/0x480 timerfd_release+0x82/0x140 __fput+0xfa/0x400 task_work_run+0x80/0xc0 exit_to_user_mode_prepare+0x155/0x160 syscall_exit_to_user_mode+0x12/0x40 do_syscall_64+0x42/0xc0 entry_SYSCALL_64_after_hwframe+0x46/0xb0 The buggy address belongs to the object at ffff889108f3d200 which belongs to the cache kmalloc-256 of size 256 The buggy address is located 0 bytes to the right of 256-byte region [ffff889108f3d200, ffff889108f3d300) The buggy address belongs to the physical page: page:000000007ef2a34c refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1108f3c head:000000007ef2a34c order:2 compound_mapcount:0 compound_pincount:0 flags: 0x4000000000010200(slab|head|zone=2) raw: 4000000000010200 0000000000000000 dead000000000001 ffff889100042b40 raw: 0000000000000000 0000000080200020 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff889108f3d200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff889108f3d280: 00 00 ---truncated---