In the Linux kernel 6.0.8, there is a use-after-free in run_unpack in fs/ntfs3/run.c, related to a difference between NTFS sector size and media sector size.

A flaw was found in the "Routing decision" classifier in the Linux kernel's Traffic Control networking subsystem in the way it handled changing of classification filters, leading to a use-after-free condition. This flaw allows unprivileged local users to escalate their privileges on the system. The highest threat from this vulnerability is to confidentiality, integrity, as well as system availability.

In drivers/net/ethernet/hisilicon/hns/hns_enet.c in the Linux kernel before 4.13, local users can cause a denial of service (use-after-free and BUG) or possibly have unspecified other impact by leveraging differences in skb handling between hns_nic_net_xmit_hw and hns_nic_net_xmit.

In the Linux kernel, the following vulnerability has been resolved: RDMA/rtrs-clt: destroy sysfs after removing session from active list A session can be removed dynamically by sysfs interface "remove_path" that eventually calls rtrs_clt_remove_path_from_sysfs function. The current rtrs_clt_remove_path_from_sysfs first removes the sysfs interfaces and frees sess->stats object. Second it removes the session from the active list. Therefore some functions could access non-connected session and access the freed sess->stats object even-if they check the session status before accessing the session. For instance rtrs_clt_request and get_next_path_min_inflight check the session status and try to send IO to the session. The session status could be changed when they are trying to send IO but they could not catch the change and update the statistics information in sess->stats object, and generate use-after-free problem. (see: "RDMA/rtrs-clt: Check state of the rtrs_clt_sess before reading its stats") This patch changes the rtrs_clt_remove_path_from_sysfs to remove the session from the active session list and then destroy the sysfs interfaces. Each function still should check the session status because closing or error recovery paths can change the status.

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: core: Fix invalid error returning in mhi_queue mhi_queue returns an error when the doorbell is not accessible in the current state. This can happen when the device is in non M0 state, like M3, and needs to be waken-up prior ringing the DB. This case is managed earlier by triggering an asynchronous M3 exit via controller resume/suspend callbacks, that in turn will cause M0 transition and DB update. So, since it's not an error but just delaying of doorbell update, there is no reason to return an error. This also fixes a use after free error for skb case, indeed a caller queuing skb will try to free the skb if the queueing fails, but in that case queueing has been done.

In the Linux kernel, the following vulnerability has been resolved: net:emac/emac-mac: Fix a use after free in emac_mac_tx_buf_send In emac_mac_tx_buf_send, it calls emac_tx_fill_tpd(..,skb,..). If some error happens in emac_tx_fill_tpd(), the skb will be freed via dev_kfree_skb(skb) in error branch of emac_tx_fill_tpd(). But the freed skb is still used via skb->len by netdev_sent_queue(,skb->len). As i observed that emac_tx_fill_tpd() haven't modified the value of skb->len, thus my patch assigns skb->len to 'len' before the possible free and use 'len' instead of skb->len later.

In the Linux kernel, the following vulnerability has been resolved: arch_topology: Avoid use-after-free for scale_freq_data Currently topology_scale_freq_tick() (which gets called from scheduler_tick()) may end up using a pointer to "struct scale_freq_data", which was previously cleared by topology_clear_scale_freq_source(), as there is no protection in place here. The users of topology_clear_scale_freq_source() though needs a guarantee that the previously cleared scale_freq_data isn't used anymore, so they can free the related resources. Since topology_scale_freq_tick() is called from scheduler tick, we don't want to add locking in there. Use the RCU update mechanism instead (which is already used by the scheduler's utilization update path) to guarantee race free updates here. synchronize_rcu() makes sure that all RCU critical sections that started before it is called, will finish before it returns. And so the callers of topology_clear_scale_freq_source() don't need to worry about their callback getting called anymore.

In the Linux kernel, the following vulnerability has been resolved: i2c: virtio: disable timeout handling If a timeout is hit, it can result is incorrect data on the I2C bus and/or memory corruptions in the guest since the device can still be operating on the buffers it was given while the guest has freed them. Here is, for example, the start of a slub_debug splat which was triggered on the next transfer after one transfer was forced to timeout by setting a breakpoint in the backend (rust-vmm/vhost-device): BUG kmalloc-1k (Not tainted): Poison overwritten First byte 0x1 instead of 0x6b Allocated in virtio_i2c_xfer+0x65/0x35c age=350 cpu=0 pid=29 __kmalloc+0xc2/0x1c9 virtio_i2c_xfer+0x65/0x35c __i2c_transfer+0x429/0x57d i2c_transfer+0x115/0x134 i2cdev_ioctl_rdwr+0x16a/0x1de i2cdev_ioctl+0x247/0x2ed vfs_ioctl+0x21/0x30 sys_ioctl+0xb18/0xb41 Freed in virtio_i2c_xfer+0x32e/0x35c age=244 cpu=0 pid=29 kfree+0x1bd/0x1cc virtio_i2c_xfer+0x32e/0x35c __i2c_transfer+0x429/0x57d i2c_transfer+0x115/0x134 i2cdev_ioctl_rdwr+0x16a/0x1de i2cdev_ioctl+0x247/0x2ed vfs_ioctl+0x21/0x30 sys_ioctl+0xb18/0xb41 There is no simple fix for this (the driver would have to always create bounce buffers and hold on to them until the device eventually returns the buffers), so just disable the timeout support for now.

In afterKeyEventLockedInterruptable of InputDispatcher.cpp, there is a possible use after free. This could lead to local escalation of privilege with no additional execution privileges needed. User interaction is not needed for exploitation.

In the Linux kernel, the following vulnerability has been resolved: net: dpaa2-eth: fix use-after-free in dpaa2_eth_remove Access to netdev after free_netdev() will cause use-after-free bug. Move debug log before free_netdev() call to avoid it.

In the Linux kernel, the following vulnerability has been resolved: net: atm: fix use after free in lec_send() The ->send() operation frees skb so save the length before calling ->send() to avoid a use after free.

In Keymaster, there is a possible EoP due to a use after free. This could lead to local escalation of privilege with no additional execution privileges needed. User interaction is not needed for exploitation. Product: AndroidVersions: Android-10Android ID: A-129562815

In the Linux kernel, the following vulnerability has been resolved: io_uring: fix ltout double free on completion race Always remove linked timeout on io_link_timeout_fn() from the master request link list, otherwise we may get use-after-free when first io_link_timeout_fn() puts linked timeout in the fail path, and then will be found and put on master's free.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix slab-use-after-free on hdcp_work [Why] A slab-use-after-free is reported when HDCP is destroyed but the property_validate_dwork queue is still running. [How] Cancel the delayed work when destroying workqueue. (cherry picked from commit 725a04ba5a95e89c89633d4322430cfbca7ce128)

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: unlink table before deleting it syzbot reports following UAF: BUG: KASAN: use-after-free in memcmp+0x18f/0x1c0 lib/string.c:955 nla_strcmp+0xf2/0x130 lib/nlattr.c:836 nft_table_lookup.part.0+0x1a2/0x460 net/netfilter/nf_tables_api.c:570 nft_table_lookup net/netfilter/nf_tables_api.c:4064 [inline] nf_tables_getset+0x1b3/0x860 net/netfilter/nf_tables_api.c:4064 nfnetlink_rcv_msg+0x659/0x13f0 net/netfilter/nfnetlink.c:285 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2504 Problem is that all get operations are lockless, so the commit_mutex held by nft_rcv_nl_event() isn't enough to stop a parallel GET request from doing read-accesses to the table object even after synchronize_rcu(). To avoid this, unlink the table first and store the table objects in on-stack scratch space.

In the Linux kernel, the following vulnerability has been resolved: can: peak_usb: fix use after free bugs After calling peak_usb_netif_rx_ni(skb), dereferencing skb is unsafe. Especially, the can_frame cf which aliases skb memory is accessed after the peak_usb_netif_rx_ni(). Reordering the lines solves the issue.

In the Linux kernel, the following vulnerability has been resolved: drm/prime: Fix use after free in mmap with drm_gem_ttm_mmap drm_gem_ttm_mmap() drops a reference to the gem object on success. If the gem object's refcount == 1 on entry to drm_gem_prime_mmap(), that drop will free the gem object, and the subsequent drm_gem_object_get() will be a UAF. Fix by grabbing a reference before calling the mmap helper. This issue was forseen when the reference dropping was adding in commit 9786b65bc61ac ("drm/ttm: fix mmap refcounting"): "For that to work properly the drm_gem_object_get() call in drm_gem_ttm_mmap() must be moved so it happens before calling obj->funcs->mmap(), otherwise the gem refcount would go down to zero."

In the Linux Kernel before versions 4.20.8 and 4.19.21 a use-after-free error in the "sctp_sendmsg()" function (net/sctp/socket.c) when handling SCTP_SENDALL flag can be exploited to corrupt memory.

In the Linux kernel, the following vulnerability has been resolved: regmap: set debugfs_name to NULL after it is freed There is a upstream commit cffa4b2122f5("regmap:debugfs: Fix a memory leak when calling regmap_attach_dev") that adds a if condition when create name for debugfs_name. With below function invoking logical, debugfs_name is freed in regmap_debugfs_exit(), but it is not created again because of the if condition introduced by above commit. regmap_reinit_cache() regmap_debugfs_exit() ... regmap_debugfs_init() So, set debugfs_name to NULL after it is freed.

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: cancel wiphy_work before freeing wiphy A wiphy_work can be queued from the moment the wiphy is allocated and initialized (i.e. wiphy_new_nm). When a wiphy_work is queued, the rdev::wiphy_work is getting queued. If wiphy_free is called before the rdev::wiphy_work had a chance to run, the wiphy memory will be freed, and then when it eventally gets to run it'll use invalid memory. Fix this by canceling the work before freeing the wiphy.

In the Linux kernel, the following vulnerability has been resolved: media: xc2028: avoid use-after-free in load_firmware_cb() syzkaller reported use-after-free in load_firmware_cb() [1]. The reason is because the module allocated a struct tuner in tuner_probe(), and then the module initialization failed, the struct tuner was released. A worker which created during module initialization accesses this struct tuner later, it caused use-after-free. The process is as follows: task-6504 worker_thread tuner_probe <= alloc dvb_frontend [2] ... request_firmware_nowait <= create a worker ... tuner_remove <= free dvb_frontend ... request_firmware_work_func <= the firmware is ready load_firmware_cb <= but now the dvb_frontend has been freed To fix the issue, check the dvd_frontend in load_firmware_cb(), if it is null, report a warning and just return. [1]: ================================================================== BUG: KASAN: use-after-free in load_firmware_cb+0x1310/0x17a0 Read of size 8 at addr ffff8000d7ca2308 by task kworker/2:3/6504 Call trace: load_firmware_cb+0x1310/0x17a0 request_firmware_work_func+0x128/0x220 process_one_work+0x770/0x1824 worker_thread+0x488/0xea0 kthread+0x300/0x430 ret_from_fork+0x10/0x20 Allocated by task 6504: kzalloc tuner_probe+0xb0/0x1430 i2c_device_probe+0x92c/0xaf0 really_probe+0x678/0xcd0 driver_probe_device+0x280/0x370 __device_attach_driver+0x220/0x330 bus_for_each_drv+0x134/0x1c0 __device_attach+0x1f4/0x410 device_initial_probe+0x20/0x30 bus_probe_device+0x184/0x200 device_add+0x924/0x12c0 device_register+0x24/0x30 i2c_new_device+0x4e0/0xc44 v4l2_i2c_new_subdev_board+0xbc/0x290 v4l2_i2c_new_subdev+0xc8/0x104 em28xx_v4l2_init+0x1dd0/0x3770 Freed by task 6504: kfree+0x238/0x4e4 tuner_remove+0x144/0x1c0 i2c_device_remove+0xc8/0x290 __device_release_driver+0x314/0x5fc device_release_driver+0x30/0x44 bus_remove_device+0x244/0x490 device_del+0x350/0x900 device_unregister+0x28/0xd0 i2c_unregister_device+0x174/0x1d0 v4l2_device_unregister+0x224/0x380 em28xx_v4l2_init+0x1d90/0x3770 The buggy address belongs to the object at ffff8000d7ca2000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 776 bytes inside of 2048-byte region [ffff8000d7ca2000, ffff8000d7ca2800) The buggy address belongs to the page: page:ffff7fe00035f280 count:1 mapcount:0 mapping:ffff8000c001f000 index:0x0 flags: 0x7ff800000000100(slab) raw: 07ff800000000100 ffff7fe00049d880 0000000300000003 ffff8000c001f000 raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8000d7ca2200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8000d7ca2280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff8000d7ca2300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff8000d7ca2380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8000d7ca2400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== [2] Actually, it is allocated for struct tuner, and dvb_frontend is inside.

In the Linux kernel, the following vulnerability has been resolved: tracing: Fix use-after-free in print_graph_function_flags during tracer switching Kairui reported a UAF issue in print_graph_function_flags() during ftrace stress testing [1]. This issue can be reproduced if puting a 'mdelay(10)' after 'mutex_unlock(&trace_types_lock)' in s_start(), and executing the following script: $ echo function_graph > current_tracer $ cat trace > /dev/null & $ sleep 5 # Ensure the 'cat' reaches the 'mdelay(10)' point $ echo timerlat > current_tracer The root cause lies in the two calls to print_graph_function_flags within print_trace_line during each s_show(): * One through 'iter->trace->print_line()'; * Another through 'event->funcs->trace()', which is hidden in print_trace_fmt() before print_trace_line returns. Tracer switching only updates the former, while the latter continues to use the print_line function of the old tracer, which in the script above is print_graph_function_flags. Moreover, when switching from the 'function_graph' tracer to the 'timerlat' tracer, s_start only calls graph_trace_close of the 'function_graph' tracer to free 'iter->private', but does not set it to NULL. This provides an opportunity for 'event->funcs->trace()' to use an invalid 'iter->private'. To fix this issue, set 'iter->private' to NULL immediately after freeing it in graph_trace_close(), ensuring that an invalid pointer is not passed to other tracers. Additionally, clean up the unnecessary 'iter->private = NULL' during each 'cat trace' when using wakeup and irqsoff tracers. [1] https://lore.kernel.org/all/20231112150030.84609-1-ryncsn@gmail.com/

In the Linux kernel, the following vulnerability has been resolved: xen-netback: take a reference to the RX task thread Do this in order to prevent the task from being freed if the thread returns (which can be triggered by the frontend) before the call to kthread_stop done as part of the backend tear down. Not taking the reference will lead to a use-after-free in that scenario. Such reference was taken before but dropped as part of the rework done in 2ac061ce97f4. Reintroduce the reference taking and add a comment this time explaining why it's needed. This is XSA-374 / CVE-2021-28691.

In the Linux kernel, the following vulnerability has been resolved: serial: liteuart: fix use-after-free and memleak on unbind Deregister the port when unbinding the driver to prevent it from being used after releasing the driver data and leaking memory allocated by serial core.

In the Linux kernel, the following vulnerability has been resolved: HID: hid-steam: Fix use-after-free when detaching device When a hid-steam device is removed it must clean up the client_hdev used for intercepting hidraw access. This can lead to scheduling deferred work to reattach the input device. Though the cleanup cancels the deferred work, this was done before the client_hdev itself is cleaned up, so it gets rescheduled. This patch fixes the ordering to make sure the deferred work is properly canceled.

In the Linux kernel, the following vulnerability has been resolved: ath10k: Fix a use after free in ath10k_htc_send_bundle In ath10k_htc_send_bundle, the bundle_skb could be freed by dev_kfree_skb_any(bundle_skb). But the bundle_skb is used later by bundle_skb->len. As skb_len = bundle_skb->len, my patch replaces bundle_skb->len to skb_len after the bundle_skb was freed.

In the Linux kernel, the following vulnerability has been resolved: md: fix mddev uaf while iterating all_mddevs list While iterating all_mddevs list from md_notify_reboot() and md_exit(), list_for_each_entry_safe is used, and this can race with deletint the next mddev, causing UAF: t1: spin_lock //list_for_each_entry_safe(mddev, n, ...) mddev_get(mddev1) // assume mddev2 is the next entry spin_unlock t2: //remove mddev2 ... mddev_free spin_lock list_del spin_unlock kfree(mddev2) mddev_put(mddev1) spin_lock //continue dereference mddev2->all_mddevs The old helper for_each_mddev() actually grab the reference of mddev2 while holding the lock, to prevent from being freed. This problem can be fixed the same way, however, the code will be complex. Hence switch to use list_for_each_entry, in this case mddev_put() can free the mddev1 and it's not safe as well. Refer to md_seq_show(), also factor out a helper mddev_put_locked() to fix this problem.

In the Linux kernel, the following vulnerability has been resolved: RDMA/core: Fix use-after-free when rename device name Syzbot reported a slab-use-after-free with the following call trace: ================================================================== BUG: KASAN: slab-use-after-free in nla_put+0xd3/0x150 lib/nlattr.c:1099 Read of size 5 at addr ffff888140ea1c60 by task syz.0.988/10025 CPU: 0 UID: 0 PID: 10025 Comm: syz.0.988 Not tainted 6.14.0-rc4-syzkaller-00859-gf77f12010f67 #0 Hardware name: Google Compute Engine, BIOS Google 02/12/2025 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:408 [inline] print_report+0x16e/0x5b0 mm/kasan/report.c:521 kasan_report+0x143/0x180 mm/kasan/report.c:634 kasan_check_range+0x282/0x290 mm/kasan/generic.c:189 __asan_memcpy+0x29/0x70 mm/kasan/shadow.c:105 nla_put+0xd3/0x150 lib/nlattr.c:1099 nla_put_string include/net/netlink.h:1621 [inline] fill_nldev_handle+0x16e/0x200 drivers/infiniband/core/nldev.c:265 rdma_nl_notify_event+0x561/0xef0 drivers/infiniband/core/nldev.c:2857 ib_device_notify_register+0x22/0x230 drivers/infiniband/core/device.c:1344 ib_register_device+0x1292/0x1460 drivers/infiniband/core/device.c:1460 rxe_register_device+0x233/0x350 drivers/infiniband/sw/rxe/rxe_verbs.c:1540 rxe_net_add+0x74/0xf0 drivers/infiniband/sw/rxe/rxe_net.c:550 rxe_newlink+0xde/0x1a0 drivers/infiniband/sw/rxe/rxe.c:212 nldev_newlink+0x5ea/0x680 drivers/infiniband/core/nldev.c:1795 rdma_nl_rcv_skb drivers/infiniband/core/netlink.c:239 [inline] rdma_nl_rcv+0x6dd/0x9e0 drivers/infiniband/core/netlink.c:259 netlink_unicast_kernel net/netlink/af_netlink.c:1313 [inline] netlink_unicast+0x7f6/0x990 net/netlink/af_netlink.c:1339 netlink_sendmsg+0x8de/0xcb0 net/netlink/af_netlink.c:1883 sock_sendmsg_nosec net/socket.c:709 [inline] __sock_sendmsg+0x221/0x270 net/socket.c:724 ____sys_sendmsg+0x53a/0x860 net/socket.c:2564 ___sys_sendmsg net/socket.c:2618 [inline] __sys_sendmsg+0x269/0x350 net/socket.c:2650 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f42d1b8d169 Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 ... RSP: 002b:00007f42d2960038 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f42d1da6320 RCX: 00007f42d1b8d169 RDX: 0000000000000000 RSI: 00004000000002c0 RDI: 000000000000000c RBP: 00007f42d1c0e2a0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000000 R14: 00007f42d1da6320 R15: 00007ffe399344a8 </TASK> Allocated by task 10025: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3f/0x80 mm/kasan/common.c:68 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0x98/0xb0 mm/kasan/common.c:394 kasan_kmalloc include/linux/kasan.h:260 [inline] __do_kmalloc_node mm/slub.c:4294 [inline] __kmalloc_node_track_caller_noprof+0x28b/0x4c0 mm/slub.c:4313 __kmemdup_nul mm/util.c:61 [inline] kstrdup+0x42/0x100 mm/util.c:81 kobject_set_name_vargs+0x61/0x120 lib/kobject.c:274 dev_set_name+0xd5/0x120 drivers/base/core.c:3468 assign_name drivers/infiniband/core/device.c:1202 [inline] ib_register_device+0x178/0x1460 drivers/infiniband/core/device.c:1384 rxe_register_device+0x233/0x350 drivers/infiniband/sw/rxe/rxe_verbs.c:1540 rxe_net_add+0x74/0xf0 drivers/infiniband/sw/rxe/rxe_net.c:550 rxe_newlink+0xde/0x1a0 drivers/infiniband/sw/rxe/rxe.c:212 nldev_newlink+0x5ea/0x680 drivers/infiniband/core/nldev.c:1795 rdma_nl_rcv_skb drivers/infiniband/core/netlink.c:239 [inline] rdma_nl_rcv+0x6dd/0x9e0 drivers/infiniband/core/netlink.c:259 netlink_unicast_kernel net/netlink/af_netlink.c:1313 [inline] netlink_unicast+0x7f6/0x990 net/netlink/af_netlink.c:1339 netlink_sendmsg+0x8de/0xcb0 net ---truncated---

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix use-after-free in lpfc_unreg_rpi() routine An error is detected with the following report when unloading the driver: "KASAN: use-after-free in lpfc_unreg_rpi+0x1b1b" The NLP_REG_LOGIN_SEND nlp_flag is set in lpfc_reg_fab_ctrl_node(), but the flag is not cleared upon completion of the login. This allows a second call to lpfc_unreg_rpi() to proceed with nlp_rpi set to LPFC_RPI_ALLOW_ERROR. This results in a use after free access when used as an rpi_ids array index. Fix by clearing the NLP_REG_LOGIN_SEND nlp_flag in lpfc_mbx_cmpl_fc_reg_login().

In the Linux kernel, the following vulnerability has been resolved: spi: Fix use-after-free with devm_spi_alloc_* We can't rely on the contents of the devres list during spi_unregister_controller(), as the list is already torn down at the time we perform devres_find() for devm_spi_release_controller. This causes devices registered with devm_spi_alloc_{master,slave}() to be mistakenly identified as legacy, non-devm managed devices and have their reference counters decremented below 0. ------------[ cut here ]------------ WARNING: CPU: 1 PID: 660 at lib/refcount.c:28 refcount_warn_saturate+0x108/0x174 [<b0396f04>] (refcount_warn_saturate) from [<b03c56a4>] (kobject_put+0x90/0x98) [<b03c5614>] (kobject_put) from [<b0447b4c>] (put_device+0x20/0x24) r4:b6700140 [<b0447b2c>] (put_device) from [<b07515e8>] (devm_spi_release_controller+0x3c/0x40) [<b07515ac>] (devm_spi_release_controller) from [<b045343c>] (release_nodes+0x84/0xc4) r5:b6700180 r4:b6700100 [<b04533b8>] (release_nodes) from [<b0454160>] (devres_release_all+0x5c/0x60) r8:b1638c54 r7:b117ad94 r6:b1638c10 r5:b117ad94 r4:b163dc10 [<b0454104>] (devres_release_all) from [<b044e41c>] (__device_release_driver+0x144/0x1ec) r5:b117ad94 r4:b163dc10 [<b044e2d8>] (__device_release_driver) from [<b044f70c>] (device_driver_detach+0x84/0xa0) r9:00000000 r8:00000000 r7:b117ad94 r6:b163dc54 r5:b1638c10 r4:b163dc10 [<b044f688>] (device_driver_detach) from [<b044d274>] (unbind_store+0xe4/0xf8) Instead, determine the devm allocation state as a flag on the controller which is guaranteed to be stable during cleanup.

In the Linux kernel, the following vulnerability has been resolved: habanalabs/gaudi: Fix a potential use after free in gaudi_memset_device_memory Our code analyzer reported a uaf. In gaudi_memset_device_memory, cb is get via hl_cb_kernel_create() with 2 refcount. If hl_cs_allocate_job() failed, the execution runs into release_cb branch. One ref of cb is dropped by hl_cb_put(cb) and could be freed if other thread also drops one ref. Then cb is used by cb->id later, which is a potential uaf. My patch add a variable 'id' to accept the value of cb->id before the hl_cb_put(cb) is called, to avoid the potential uaf.

In the Linux kernel, the following vulnerability has been resolved: ipvlan: Fix use-after-free in ipvlan_get_iflink(). syzbot presented an use-after-free report [0] regarding ipvlan and linkwatch. ipvlan does not hold a refcnt of the lower device unlike vlan and macvlan. If the linkwatch work is triggered for the ipvlan dev, the lower dev might have already been freed, resulting in UAF of ipvlan->phy_dev in ipvlan_get_iflink(). We can delay the lower dev unregistration like vlan and macvlan by holding the lower dev's refcnt in dev->netdev_ops->ndo_init() and releasing it in dev->priv_destructor(). Jakub pointed out calling .ndo_XXX after unregister_netdevice() has returned is error prone and suggested [1] addressing this UAF in the core by taking commit 750e51603395 ("net: avoid potential UAF in default_operstate()") further. Let's assume unregistering devices DOWN and use RCU protection in default_operstate() not to race with the device unregistration. [0]: BUG: KASAN: slab-use-after-free in ipvlan_get_iflink+0x84/0x88 drivers/net/ipvlan/ipvlan_main.c:353 Read of size 4 at addr ffff0000d768c0e0 by task kworker/u8:35/6944 CPU: 0 UID: 0 PID: 6944 Comm: kworker/u8:35 Not tainted 6.13.0-rc2-g9bc5c9515b48 #12 4c3cb9e8b4565456f6a355f312ff91f4f29b3c47 Hardware name: linux,dummy-virt (DT) Workqueue: events_unbound linkwatch_event Call trace: show_stack+0x38/0x50 arch/arm64/kernel/stacktrace.c:484 (C) __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0xbc/0x108 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0x16c/0x6f0 mm/kasan/report.c:489 kasan_report+0xc0/0x120 mm/kasan/report.c:602 __asan_report_load4_noabort+0x20/0x30 mm/kasan/report_generic.c:380 ipvlan_get_iflink+0x84/0x88 drivers/net/ipvlan/ipvlan_main.c:353 dev_get_iflink+0x7c/0xd8 net/core/dev.c:674 default_operstate net/core/link_watch.c:45 [inline] rfc2863_policy+0x144/0x360 net/core/link_watch.c:72 linkwatch_do_dev+0x60/0x228 net/core/link_watch.c:175 __linkwatch_run_queue+0x2f4/0x5b8 net/core/link_watch.c:239 linkwatch_event+0x64/0xa8 net/core/link_watch.c:282 process_one_work+0x700/0x1398 kernel/workqueue.c:3229 process_scheduled_works kernel/workqueue.c:3310 [inline] worker_thread+0x8c4/0xe10 kernel/workqueue.c:3391 kthread+0x2b0/0x360 kernel/kthread.c:389 ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:862 Allocated by task 9303: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x30/0x68 mm/kasan/common.c:68 kasan_save_alloc_info+0x44/0x58 mm/kasan/generic.c:568 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0x84/0xa0 mm/kasan/common.c:394 kasan_kmalloc include/linux/kasan.h:260 [inline] __do_kmalloc_node mm/slub.c:4283 [inline] __kmalloc_node_noprof+0x2a0/0x560 mm/slub.c:4289 __kvmalloc_node_noprof+0x9c/0x230 mm/util.c:650 alloc_netdev_mqs+0xb4/0x1118 net/core/dev.c:11209 rtnl_create_link+0x2b8/0xb60 net/core/rtnetlink.c:3595 rtnl_newlink_create+0x19c/0x868 net/core/rtnetlink.c:3771 __rtnl_newlink net/core/rtnetlink.c:3896 [inline] rtnl_newlink+0x122c/0x15c0 net/core/rtnetlink.c:4011 rtnetlink_rcv_msg+0x61c/0x918 net/core/rtnetlink.c:6901 netlink_rcv_skb+0x1dc/0x398 net/netlink/af_netlink.c:2542 rtnetlink_rcv+0x34/0x50 net/core/rtnetlink.c:6928 netlink_unicast_kernel net/netlink/af_netlink.c:1321 [inline] netlink_unicast+0x618/0x838 net/netlink/af_netlink.c:1347 netlink_sendmsg+0x5fc/0x8b0 net/netlink/af_netlink.c:1891 sock_sendmsg_nosec net/socket.c:711 [inline] __sock_sendmsg net/socket.c:726 [inline] __sys_sendto+0x2ec/0x438 net/socket.c:2197 __do_sys_sendto net/socket.c:2204 [inline] __se_sys_sendto net/socket.c:2200 [inline] __arm64_sys_sendto+0xe4/0x110 net/socket.c:2200 __invoke_syscall arch/arm64/kernel/syscall.c:35 [inline] invoke_syscall+0x90/0x278 arch/arm64/kernel/syscall.c:49 el0_svc_common+0x13c/0x250 arch/arm64/kernel/syscall.c:132 do_el0_svc+0x54/0x70 arch/arm64/kernel/syscall.c:151 el ---truncated---

In the Linux kernel, the following vulnerability has been resolved: geneve: Fix use-after-free in geneve_find_dev(). syzkaller reported a use-after-free in geneve_find_dev() [0] without repro. geneve_configure() links struct geneve_dev.next to net_generic(net, geneve_net_id)->geneve_list. The net here could differ from dev_net(dev) if IFLA_NET_NS_PID, IFLA_NET_NS_FD, or IFLA_TARGET_NETNSID is set. When dev_net(dev) is dismantled, geneve_exit_batch_rtnl() finally calls unregister_netdevice_queue() for each dev in the netns, and later the dev is freed. However, its geneve_dev.next is still linked to the backend UDP socket netns. Then, use-after-free will occur when another geneve dev is created in the netns. Let's call geneve_dellink() instead in geneve_destroy_tunnels(). [0]: BUG: KASAN: slab-use-after-free in geneve_find_dev drivers/net/geneve.c:1295 [inline] BUG: KASAN: slab-use-after-free in geneve_configure+0x234/0x858 drivers/net/geneve.c:1343 Read of size 2 at addr ffff000054d6ee24 by task syz.1.4029/13441 CPU: 1 UID: 0 PID: 13441 Comm: syz.1.4029 Not tainted 6.13.0-g0ad9617c78ac #24 dc35ca22c79fb82e8e7bc5c9c9adafea898b1e3d Hardware name: linux,dummy-virt (DT) Call trace: show_stack+0x38/0x50 arch/arm64/kernel/stacktrace.c:466 (C) __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0xbc/0x108 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0x16c/0x6f0 mm/kasan/report.c:489 kasan_report+0xc0/0x120 mm/kasan/report.c:602 __asan_report_load2_noabort+0x20/0x30 mm/kasan/report_generic.c:379 geneve_find_dev drivers/net/geneve.c:1295 [inline] geneve_configure+0x234/0x858 drivers/net/geneve.c:1343 geneve_newlink+0xb8/0x128 drivers/net/geneve.c:1634 rtnl_newlink_create+0x23c/0x868 net/core/rtnetlink.c:3795 __rtnl_newlink net/core/rtnetlink.c:3906 [inline] rtnl_newlink+0x1054/0x1630 net/core/rtnetlink.c:4021 rtnetlink_rcv_msg+0x61c/0x918 net/core/rtnetlink.c:6911 netlink_rcv_skb+0x1dc/0x398 net/netlink/af_netlink.c:2543 rtnetlink_rcv+0x34/0x50 net/core/rtnetlink.c:6938 netlink_unicast_kernel net/netlink/af_netlink.c:1322 [inline] netlink_unicast+0x618/0x838 net/netlink/af_netlink.c:1348 netlink_sendmsg+0x5fc/0x8b0 net/netlink/af_netlink.c:1892 sock_sendmsg_nosec net/socket.c:713 [inline] __sock_sendmsg net/socket.c:728 [inline] ____sys_sendmsg+0x410/0x6f8 net/socket.c:2568 ___sys_sendmsg+0x178/0x1d8 net/socket.c:2622 __sys_sendmsg net/socket.c:2654 [inline] __do_sys_sendmsg net/socket.c:2659 [inline] __se_sys_sendmsg net/socket.c:2657 [inline] __arm64_sys_sendmsg+0x12c/0x1c8 net/socket.c:2657 __invoke_syscall arch/arm64/kernel/syscall.c:35 [inline] invoke_syscall+0x90/0x278 arch/arm64/kernel/syscall.c:49 el0_svc_common+0x13c/0x250 arch/arm64/kernel/syscall.c:132 do_el0_svc+0x54/0x70 arch/arm64/kernel/syscall.c:151 el0_svc+0x4c/0xa8 arch/arm64/kernel/entry-common.c:744 el0t_64_sync_handler+0x78/0x108 arch/arm64/kernel/entry-common.c:762 el0t_64_sync+0x198/0x1a0 arch/arm64/kernel/entry.S:600 Allocated by task 13247: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x30/0x68 mm/kasan/common.c:68 kasan_save_alloc_info+0x44/0x58 mm/kasan/generic.c:568 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0x84/0xa0 mm/kasan/common.c:394 kasan_kmalloc include/linux/kasan.h:260 [inline] __do_kmalloc_node mm/slub.c:4298 [inline] __kmalloc_node_noprof+0x2a0/0x560 mm/slub.c:4304 __kvmalloc_node_noprof+0x9c/0x230 mm/util.c:645 alloc_netdev_mqs+0xb8/0x11a0 net/core/dev.c:11470 rtnl_create_link+0x2b8/0xb50 net/core/rtnetlink.c:3604 rtnl_newlink_create+0x19c/0x868 net/core/rtnetlink.c:3780 __rtnl_newlink net/core/rtnetlink.c:3906 [inline] rtnl_newlink+0x1054/0x1630 net/core/rtnetlink.c:4021 rtnetlink_rcv_msg+0x61c/0x918 net/core/rtnetlink.c:6911 netlink_rcv_skb+0x1dc/0x398 net/netlink/af_netlink.c:2543 rtnetlink_rcv+0x34/0x50 net/core/rtnetlink.c:6938 netlink_unicast_kernel net/netlink/af_n ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ice: Fix deinitializing VF in error path If ice_ena_vfs() fails after calling ice_create_vf_entries(), it frees all VFs without removing them from snapshot PF-VF mailbox list, leading to list corruption. Reproducer: devlink dev eswitch set $PF1_PCI mode switchdev ip l s $PF1 up ip l s $PF1 promisc on sleep 1 echo 1 > /sys/class/net/$PF1/device/sriov_numvfs sleep 1 echo 1 > /sys/class/net/$PF1/device/sriov_numvfs Trace (minimized): list_add corruption. next->prev should be prev (ffff8882e241c6f0), but was 0000000000000000. (next=ffff888455da1330). kernel BUG at lib/list_debug.c:29! RIP: 0010:__list_add_valid_or_report+0xa6/0x100 ice_mbx_init_vf_info+0xa7/0x180 [ice] ice_initialize_vf_entry+0x1fa/0x250 [ice] ice_sriov_configure+0x8d7/0x1520 [ice] ? __percpu_ref_switch_mode+0x1b1/0x5d0 ? __pfx_ice_sriov_configure+0x10/0x10 [ice] Sometimes a KASAN report can be seen instead with a similar stack trace: BUG: KASAN: use-after-free in __list_add_valid_or_report+0xf1/0x100 VFs are added to this list in ice_mbx_init_vf_info(), but only removed in ice_free_vfs(). Move the removing to ice_free_vf_entries(), which is also being called in other places where VFs are being removed (including ice_free_vfs() itself).

NVIDIA Linux distributions contain a vulnerability in nvmap ioctl, which allows any user with a local account to exploit a use-after-free condition, leading to code privilege escalation, loss of confidentiality and integrity, or denial of service.

In the Linux kernel, the following vulnerability has been resolved: can: vxcan: vxcan_xmit: fix use after free bug After calling netif_rx_ni(skb), dereferencing skb is unsafe. Especially, the canfd_frame cfd which aliases skb memory is accessed after the netif_rx_ni().

In the Linux kernel, the following vulnerability has been resolved: staging: greybus: uart: fix tty use after free User space can hold a tty open indefinitely and tty drivers must not release the underlying structures until the last user is gone. Switch to using the tty-port reference counter to manage the life time of the greybus tty state to avoid use after free after a disconnect.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: fix use-after-free in nft_set_catchall_destroy() We need to use list_for_each_entry_safe() iterator because we can not access @catchall after kfree_rcu() call. syzbot reported: BUG: KASAN: use-after-free in nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline] BUG: KASAN: use-after-free in nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline] BUG: KASAN: use-after-free in nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493 Read of size 8 at addr ffff8880716e5b80 by task syz-executor.3/8871 CPU: 1 PID: 8871 Comm: syz-executor.3 Not tainted 5.16.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_address_description.constprop.0.cold+0x8d/0x2ed mm/kasan/report.c:247 __kasan_report mm/kasan/report.c:433 [inline] kasan_report.cold+0x83/0xdf mm/kasan/report.c:450 nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline] nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline] nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493 __nft_release_table+0x79f/0xcd0 net/netfilter/nf_tables_api.c:9626 nft_rcv_nl_event+0x4f8/0x670 net/netfilter/nf_tables_api.c:9688 notifier_call_chain+0xb5/0x200 kernel/notifier.c:83 blocking_notifier_call_chain kernel/notifier.c:318 [inline] blocking_notifier_call_chain+0x67/0x90 kernel/notifier.c:306 netlink_release+0xcb6/0x1dd0 net/netlink/af_netlink.c:788 __sock_release+0xcd/0x280 net/socket.c:649 sock_close+0x18/0x20 net/socket.c:1314 __fput+0x286/0x9f0 fs/file_table.c:280 task_work_run+0xdd/0x1a0 kernel/task_work.c:164 tracehook_notify_resume include/linux/tracehook.h:189 [inline] exit_to_user_mode_loop kernel/entry/common.c:175 [inline] exit_to_user_mode_prepare+0x27e/0x290 kernel/entry/common.c:207 __syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline] syscall_exit_to_user_mode+0x19/0x60 kernel/entry/common.c:300 do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f75fbf28adb Code: 0f 05 48 3d 00 f0 ff ff 77 45 c3 0f 1f 40 00 48 83 ec 18 89 7c 24 0c e8 63 fc ff ff 8b 7c 24 0c 41 89 c0 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 35 44 89 c7 89 44 24 0c e8 a1 fc ff ff 8b 44 RSP: 002b:00007ffd8da7ec10 EFLAGS: 00000293 ORIG_RAX: 0000000000000003 RAX: 0000000000000000 RBX: 0000000000000004 RCX: 00007f75fbf28adb RDX: 00007f75fc08e828 RSI: ffffffffffffffff RDI: 0000000000000003 RBP: 00007f75fc08a960 R08: 0000000000000000 R09: 00007f75fc08e830 R10: 00007ffd8da7ed10 R11: 0000000000000293 R12: 00000000002067c3 R13: 00007ffd8da7ed10 R14: 00007f75fc088f60 R15: 0000000000000032 </TASK> Allocated by task 8886: kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38 kasan_set_track mm/kasan/common.c:46 [inline] set_alloc_info mm/kasan/common.c:434 [inline] ____kasan_kmalloc mm/kasan/common.c:513 [inline] ____kasan_kmalloc mm/kasan/common.c:472 [inline] __kasan_kmalloc+0xa6/0xd0 mm/kasan/common.c:522 kasan_kmalloc include/linux/kasan.h:269 [inline] kmem_cache_alloc_trace+0x1ea/0x4a0 mm/slab.c:3575 kmalloc include/linux/slab.h:590 [inline] nft_setelem_catchall_insert net/netfilter/nf_tables_api.c:5544 [inline] nft_setelem_insert net/netfilter/nf_tables_api.c:5562 [inline] nft_add_set_elem+0x232e/0x2f40 net/netfilter/nf_tables_api.c:5936 nf_tables_newsetelem+0x6ff/0xbb0 net/netfilter/nf_tables_api.c:6032 nfnetlink_rcv_batch+0x1710/0x25f0 net/netfilter/nfnetlink.c:513 nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline] nfnetlink_rcv+0x3af/0x420 net/netfilter/nfnetlink.c:652 netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline] netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1345 netlink_sendmsg+0x904/0xdf0 net/netlink/af_netlink.c:1921 sock_sendmsg_nosec net/ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ndisc: extend RCU protection in ndisc_send_skb() ndisc_send_skb() can be called without RTNL or RCU held. Acquire rcu_read_lock() earlier, so that we can use dev_net_rcu() and avoid a potential UAF.

In the Linux kernel, the following vulnerability has been resolved: aio: fix use-after-free due to missing POLLFREE handling signalfd_poll() and binder_poll() are special in that they use a waitqueue whose lifetime is the current task, rather than the struct file as is normally the case. This is okay for blocking polls, since a blocking poll occurs within one task; however, non-blocking polls require another solution. This solution is for the queue to be cleared before it is freed, by sending a POLLFREE notification to all waiters. Unfortunately, only eventpoll handles POLLFREE. A second type of non-blocking poll, aio poll, was added in kernel v4.18, and it doesn't handle POLLFREE. This allows a use-after-free to occur if a signalfd or binder fd is polled with aio poll, and the waitqueue gets freed. Fix this by making aio poll handle POLLFREE. A patch by Ramji Jiyani <ramjiyani@google.com> (https://lore.kernel.org/r/20211027011834.2497484-1-ramjiyani@google.com) tried to do this by making aio_poll_wake() always complete the request inline if POLLFREE is seen. However, that solution had two bugs. First, it introduced a deadlock, as it unconditionally locked the aio context while holding the waitqueue lock, which inverts the normal locking order. Second, it didn't consider that POLLFREE notifications are missed while the request has been temporarily de-queued. The second problem was solved by my previous patch. This patch then properly fixes the use-after-free by handling POLLFREE in a deadlock-free way. It does this by taking advantage of the fact that freeing of the waitqueue is RCU-delayed, similar to what eventpoll does.

In the Linux kernel, the following vulnerability has been resolved: sctp: do asoc update earlier in sctp_sf_do_dupcook_a There's a panic that occurs in a few of envs, the call trace is as below: [] general protection fault, ... 0x29acd70f1000a: 0000 [#1] SMP PTI [] RIP: 0010:sctp_ulpevent_notify_peer_addr_change+0x4b/0x1fa [sctp] [] sctp_assoc_control_transport+0x1b9/0x210 [sctp] [] sctp_do_8_2_transport_strike.isra.16+0x15c/0x220 [sctp] [] sctp_cmd_interpreter.isra.21+0x1231/0x1a10 [sctp] [] sctp_do_sm+0xc3/0x2a0 [sctp] [] sctp_generate_timeout_event+0x81/0xf0 [sctp] This is caused by a transport use-after-free issue. When processing a duplicate COOKIE-ECHO chunk in sctp_sf_do_dupcook_a(), both COOKIE-ACK and SHUTDOWN chunks are allocated with the transort from the new asoc. However, later in the sideeffect machine, the old asoc is used to send them out and old asoc's shutdown_last_sent_to is set to the transport that SHUTDOWN chunk attached to in sctp_cmd_setup_t2(), which actually belongs to the new asoc. After the new_asoc is freed and the old asoc T2 timeout, the old asoc's shutdown_last_sent_to that is already freed would be accessed in sctp_sf_t2_timer_expire(). Thanks Alexander and Jere for helping dig into this issue. To fix it, this patch is to do the asoc update first, then allocate the COOKIE-ACK and SHUTDOWN chunks with the 'updated' old asoc. This would make more sense, as a chunk from an asoc shouldn't be sent out with another asoc. We had fixed quite a few issues caused by this.

In the Linux kernel, the following vulnerability has been resolved: HID: corsair-void: Add missing delayed work cancel for headset status The cancel_delayed_work_sync() call was missed, causing a use-after-free in corsair_void_remove().

A use after free issue was addressed with improved memory management. This issue is fixed in macOS Mojave 10.14.4. An application may be able to gain elevated privileges.

In the Linux kernel, the following vulnerability has been resolved: workqueue: Put the pwq after detaching the rescuer from the pool The commit 68f83057b913("workqueue: Reap workers via kthread_stop() and remove detach_completion") adds code to reap the normal workers but mistakenly does not handle the rescuer and also removes the code waiting for the rescuer in put_unbound_pool(), which caused a use-after-free bug reported by Cheung Wall. To avoid the use-after-free bug, the pool’s reference must be held until the detachment is complete. Therefore, move the code that puts the pwq after detaching the rescuer from the pool.

Memory corruption while processing a private escape command in an event trigger.

In the Linux kernel, the following vulnerability has been resolved: ibmvnic: Don't reference skb after sending to VIOS Previously, after successfully flushing the xmit buffer to VIOS, the tx_bytes stat was incremented by the length of the skb. It is invalid to access the skb memory after sending the buffer to the VIOS because, at any point after sending, the VIOS can trigger an interrupt to free this memory. A race between reading skb->len and freeing the skb is possible (especially during LPM) and will result in use-after-free: ================================================================== BUG: KASAN: slab-use-after-free in ibmvnic_xmit+0x75c/0x1808 [ibmvnic] Read of size 4 at addr c00000024eb48a70 by task hxecom/14495 <...> Call Trace: [c000000118f66cf0] [c0000000018cba6c] dump_stack_lvl+0x84/0xe8 (unreliable) [c000000118f66d20] [c0000000006f0080] print_report+0x1a8/0x7f0 [c000000118f66df0] [c0000000006f08f0] kasan_report+0x128/0x1f8 [c000000118f66f00] [c0000000006f2868] __asan_load4+0xac/0xe0 [c000000118f66f20] [c0080000046eac84] ibmvnic_xmit+0x75c/0x1808 [ibmvnic] [c000000118f67340] [c0000000014be168] dev_hard_start_xmit+0x150/0x358 <...> Freed by task 0: kasan_save_stack+0x34/0x68 kasan_save_track+0x2c/0x50 kasan_save_free_info+0x64/0x108 __kasan_mempool_poison_object+0x148/0x2d4 napi_skb_cache_put+0x5c/0x194 net_tx_action+0x154/0x5b8 handle_softirqs+0x20c/0x60c do_softirq_own_stack+0x6c/0x88 <...> The buggy address belongs to the object at c00000024eb48a00 which belongs to the cache skbuff_head_cache of size 224 ==================================================================

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix use-after-free on inode when scanning root during em shrinking At btrfs_scan_root() we are accessing the inode's root (and fs_info) in a call to btrfs_fs_closing() after we have scheduled the inode for a delayed iput, and that can result in a use-after-free on the inode in case the cleaner kthread does the iput before we dereference the inode in the call to btrfs_fs_closing(). Fix this by using the fs_info stored already in a local variable instead of doing inode->root->fs_info.

Memory corruption while calling the NPU driver APIs concurrently.

In the Linux kernel, the following vulnerability has been resolved: vsock: Keep the binding until socket destruction Preserve sockets bindings; this includes both resulting from an explicit bind() and those implicitly bound through autobind during connect(). Prevents socket unbinding during a transport reassignment, which fixes a use-after-free: 1. vsock_create() (refcnt=1) calls vsock_insert_unbound() (refcnt=2) 2. transport->release() calls vsock_remove_bound() without checking if sk was bound and moved to bound list (refcnt=1) 3. vsock_bind() assumes sk is in unbound list and before __vsock_insert_bound(vsock_bound_sockets()) calls __vsock_remove_bound() which does: list_del_init(&vsk->bound_table); // nop sock_put(&vsk->sk); // refcnt=0 BUG: KASAN: slab-use-after-free in __vsock_bind+0x62e/0x730 Read of size 4 at addr ffff88816b46a74c by task a.out/2057 dump_stack_lvl+0x68/0x90 print_report+0x174/0x4f6 kasan_report+0xb9/0x190 __vsock_bind+0x62e/0x730 vsock_bind+0x97/0xe0 __sys_bind+0x154/0x1f0 __x64_sys_bind+0x6e/0xb0 do_syscall_64+0x93/0x1b0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Allocated by task 2057: kasan_save_stack+0x1e/0x40 kasan_save_track+0x10/0x30 __kasan_slab_alloc+0x85/0x90 kmem_cache_alloc_noprof+0x131/0x450 sk_prot_alloc+0x5b/0x220 sk_alloc+0x2c/0x870 __vsock_create.constprop.0+0x2e/0xb60 vsock_create+0xe4/0x420 __sock_create+0x241/0x650 __sys_socket+0xf2/0x1a0 __x64_sys_socket+0x6e/0xb0 do_syscall_64+0x93/0x1b0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Freed by task 2057: kasan_save_stack+0x1e/0x40 kasan_save_track+0x10/0x30 kasan_save_free_info+0x37/0x60 __kasan_slab_free+0x4b/0x70 kmem_cache_free+0x1a1/0x590 __sk_destruct+0x388/0x5a0 __vsock_bind+0x5e1/0x730 vsock_bind+0x97/0xe0 __sys_bind+0x154/0x1f0 __x64_sys_bind+0x6e/0xb0 do_syscall_64+0x93/0x1b0 entry_SYSCALL_64_after_hwframe+0x76/0x7e refcount_t: addition on 0; use-after-free. WARNING: CPU: 7 PID: 2057 at lib/refcount.c:25 refcount_warn_saturate+0xce/0x150 RIP: 0010:refcount_warn_saturate+0xce/0x150 __vsock_bind+0x66d/0x730 vsock_bind+0x97/0xe0 __sys_bind+0x154/0x1f0 __x64_sys_bind+0x6e/0xb0 do_syscall_64+0x93/0x1b0 entry_SYSCALL_64_after_hwframe+0x76/0x7e refcount_t: underflow; use-after-free. WARNING: CPU: 7 PID: 2057 at lib/refcount.c:28 refcount_warn_saturate+0xee/0x150 RIP: 0010:refcount_warn_saturate+0xee/0x150 vsock_remove_bound+0x187/0x1e0 __vsock_release+0x383/0x4a0 vsock_release+0x90/0x120 __sock_release+0xa3/0x250 sock_close+0x14/0x20 __fput+0x359/0xa80 task_work_run+0x107/0x1d0 do_exit+0x847/0x2560 do_group_exit+0xb8/0x250 __x64_sys_exit_group+0x3a/0x50 x64_sys_call+0xfec/0x14f0 do_syscall_64+0x93/0x1b0 entry_SYSCALL_64_after_hwframe+0x76/0x7e

In the Linux kernel, the following vulnerability has been resolved: bpf, test_run: Fix use-after-free issue in eth_skb_pkt_type() KMSAN reported a use-after-free issue in eth_skb_pkt_type()[1]. The cause of the issue was that eth_skb_pkt_type() accessed skb's data that didn't contain an Ethernet header. This occurs when bpf_prog_test_run_xdp() passes an invalid value as the user_data argument to bpf_test_init(). Fix this by returning an error when user_data is less than ETH_HLEN in bpf_test_init(). Additionally, remove the check for "if (user_size > size)" as it is unnecessary. [1] BUG: KMSAN: use-after-free in eth_skb_pkt_type include/linux/etherdevice.h:627 [inline] BUG: KMSAN: use-after-free in eth_type_trans+0x4ee/0x980 net/ethernet/eth.c:165 eth_skb_pkt_type include/linux/etherdevice.h:627 [inline] eth_type_trans+0x4ee/0x980 net/ethernet/eth.c:165 __xdp_build_skb_from_frame+0x5a8/0xa50 net/core/xdp.c:635 xdp_recv_frames net/bpf/test_run.c:272 [inline] xdp_test_run_batch net/bpf/test_run.c:361 [inline] bpf_test_run_xdp_live+0x2954/0x3330 net/bpf/test_run.c:390 bpf_prog_test_run_xdp+0x148e/0x1b10 net/bpf/test_run.c:1318 bpf_prog_test_run+0x5b7/0xa30 kernel/bpf/syscall.c:4371 __sys_bpf+0x6a6/0xe20 kernel/bpf/syscall.c:5777 __do_sys_bpf kernel/bpf/syscall.c:5866 [inline] __se_sys_bpf kernel/bpf/syscall.c:5864 [inline] __x64_sys_bpf+0xa4/0xf0 kernel/bpf/syscall.c:5864 x64_sys_call+0x2ea0/0x3d90 arch/x86/include/generated/asm/syscalls_64.h:322 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xd9/0x1d0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was created at: free_pages_prepare mm/page_alloc.c:1056 [inline] free_unref_page+0x156/0x1320 mm/page_alloc.c:2657 __free_pages+0xa3/0x1b0 mm/page_alloc.c:4838 bpf_ringbuf_free kernel/bpf/ringbuf.c:226 [inline] ringbuf_map_free+0xff/0x1e0 kernel/bpf/ringbuf.c:235 bpf_map_free kernel/bpf/syscall.c:838 [inline] bpf_map_free_deferred+0x17c/0x310 kernel/bpf/syscall.c:862 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0xa2b/0x1b60 kernel/workqueue.c:3310 worker_thread+0xedf/0x1550 kernel/workqueue.c:3391 kthread+0x535/0x6b0 kernel/kthread.c:389 ret_from_fork+0x6e/0x90 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 CPU: 1 UID: 0 PID: 17276 Comm: syz.1.16450 Not tainted 6.12.0-05490-g9bb88c659673 #8 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014