In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btrtl: Prevent potential NULL dereference The btrtl_initialize() function checks that rtl_load_file() either had an error or it loaded a zero length file. However, if it loaded a zero length file then the error code is not set correctly. It results in an error pointer vs NULL bug, followed by a NULL pointer dereference. This was detected by Smatch: drivers/bluetooth/btrtl.c:592 btrtl_initialize() warn: passing zero to 'ERR_PTR'

In the Linux kernel, the following vulnerability has been resolved: net: dsa: mv88e6xxx: avoid unregistering devlink regions which were never registered Russell King reports that a system with mv88e6xxx dereferences a NULL pointer when unbinding this driver: https://lore.kernel.org/netdev/Z_lRkMlTJ1KQ0kVX@shell.armlinux.org.uk/ The crash seems to be in devlink_region_destroy(), which is not NULL tolerant but is given a NULL devlink global region pointer. At least on some chips, some devlink regions are conditionally registered since the blamed commit, see mv88e6xxx_setup_devlink_regions_global(): if (cond && !cond(chip)) continue; These are MV88E6XXX_REGION_STU and MV88E6XXX_REGION_PVT. If the chip does not have an STU or PVT, it should crash like this. To fix the issue, avoid unregistering those regions which are NULL, i.e. were skipped at mv88e6xxx_setup_devlink_regions_global() time.

In the Linux kernel, the following vulnerability has been resolved: net: ti: icss-iep: Fix possible NULL pointer dereference for perout request The ICSS IEP driver tracks perout and pps enable state with flags. Currently when disabling pps and perout signals during icss_iep_exit(), results in NULL pointer dereference for perout. To fix the null pointer dereference issue, the icss_iep_perout_enable_hw function can be modified to directly clear the IEP CMP registers when disabling PPS or PEROUT, without referencing the ptp_perout_request structure, as its contents are irrelevant in this case.

In the Linux kernel, the following vulnerability has been resolved: drm/msm/dpu: Fix error pointers in dpu_plane_virtual_atomic_check The function dpu_plane_virtual_atomic_check was dereferencing pointers returned by drm_atomic_get_plane_state without checking for errors. This could lead to undefined behavior if the function returns an error pointer. This commit adds checks using IS_ERR to ensure that plane_state is valid before dereferencing them. Similar to commit da29abe71e16 ("drm/amd/display: Fix error pointers in amdgpu_dm_crtc_mem_type_changed"). Patchwork: https://patchwork.freedesktop.org/patch/643132/

In the Linux kernel, the following vulnerability has been resolved: i2c: cros-ec-tunnel: defer probe if parent EC is not present When i2c-cros-ec-tunnel and the EC driver are built-in, the EC parent device will not be found, leading to NULL pointer dereference. That can also be reproduced by unbinding the controller driver and then loading i2c-cros-ec-tunnel module (or binding the device). [ 271.991245] BUG: kernel NULL pointer dereference, address: 0000000000000058 [ 271.998215] #PF: supervisor read access in kernel mode [ 272.003351] #PF: error_code(0x0000) - not-present page [ 272.008485] PGD 0 P4D 0 [ 272.011022] Oops: Oops: 0000 [#1] SMP NOPTI [ 272.015207] CPU: 0 UID: 0 PID: 3859 Comm: insmod Tainted: G S 6.15.0-rc1-00004-g44722359ed83 #30 PREEMPT(full) 3c7fb39a552e7d949de2ad921a7d6588d3a4fdc5 [ 272.030312] Tainted: [S]=CPU_OUT_OF_SPEC [ 272.034233] Hardware name: HP Berknip/Berknip, BIOS Google_Berknip.13434.356.0 05/17/2021 [ 272.042400] RIP: 0010:ec_i2c_probe+0x2b/0x1c0 [i2c_cros_ec_tunnel] [ 272.048577] Code: 1f 44 00 00 41 57 41 56 41 55 41 54 53 48 83 ec 10 65 48 8b 05 06 a0 6c e7 48 89 44 24 08 4c 8d 7f 10 48 8b 47 50 4c 8b 60 78 <49> 83 7c 24 58 00 0f 84 2f 01 00 00 48 89 fb be 30 06 00 00 4c 9 [ 272.067317] RSP: 0018:ffffa32082a03940 EFLAGS: 00010282 [ 272.072541] RAX: ffff969580b6a810 RBX: ffff969580b68c10 RCX: 0000000000000000 [ 272.079672] RDX: 0000000000000000 RSI: 0000000000000282 RDI: ffff969580b68c00 [ 272.086804] RBP: 00000000fffffdfb R08: 0000000000000000 R09: 0000000000000000 [ 272.093936] R10: 0000000000000000 R11: ffffffffc0600000 R12: 0000000000000000 [ 272.101067] R13: ffffffffa666fbb8 R14: ffffffffc05b5528 R15: ffff969580b68c10 [ 272.108198] FS: 00007b930906fc40(0000) GS:ffff969603149000(0000) knlGS:0000000000000000 [ 272.116282] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 272.122024] CR2: 0000000000000058 CR3: 000000012631c000 CR4: 00000000003506f0 [ 272.129155] Call Trace: [ 272.131606] <TASK> [ 272.133709] ? acpi_dev_pm_attach+0xdd/0x110 [ 272.137985] platform_probe+0x69/0xa0 [ 272.141652] really_probe+0x152/0x310 [ 272.145318] __driver_probe_device+0x77/0x110 [ 272.149678] driver_probe_device+0x1e/0x190 [ 272.153864] __driver_attach+0x10b/0x1e0 [ 272.157790] ? driver_attach+0x20/0x20 [ 272.161542] bus_for_each_dev+0x107/0x150 [ 272.165553] bus_add_driver+0x15d/0x270 [ 272.169392] driver_register+0x65/0x110 [ 272.173232] ? cleanup_module+0xa80/0xa80 [i2c_cros_ec_tunnel 3a00532f3f4af4a9eade753f86b0f8dd4e4e5698] [ 272.182617] do_one_initcall+0x110/0x350 [ 272.186543] ? security_kernfs_init_security+0x49/0xd0 [ 272.191682] ? __kernfs_new_node+0x1b9/0x240 [ 272.195954] ? security_kernfs_init_security+0x49/0xd0 [ 272.201093] ? __kernfs_new_node+0x1b9/0x240 [ 272.205365] ? kernfs_link_sibling+0x105/0x130 [ 272.209810] ? kernfs_next_descendant_post+0x1c/0xa0 [ 272.214773] ? kernfs_activate+0x57/0x70 [ 272.218699] ? kernfs_add_one+0x118/0x160 [ 272.222710] ? __kernfs_create_file+0x71/0xa0 [ 272.227069] ? sysfs_add_bin_file_mode_ns+0xd6/0x110 [ 272.232033] ? internal_create_group+0x453/0x4a0 [ 272.236651] ? __vunmap_range_noflush+0x214/0x2d0 [ 272.241355] ? __free_frozen_pages+0x1dc/0x420 [ 272.245799] ? free_vmap_area_noflush+0x10a/0x1c0 [ 272.250505] ? load_module+0x1509/0x16f0 [ 272.254431] do_init_module+0x60/0x230 [ 272.258181] __se_sys_finit_module+0x27a/0x370 [ 272.262627] do_syscall_64+0x6a/0xf0 [ 272.266206] ? do_syscall_64+0x76/0xf0 [ 272.269956] ? irqentry_exit_to_user_mode+0x79/0x90 [ 272.274836] entry_SYSCALL_64_after_hwframe+0x55/0x5d [ 272.279887] RIP: 0033:0x7b9309168d39 [ 272.283466] Code: 5b 41 5c 5d c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d af 40 0c 00 f7 d8 64 89 01 8 [ 272.302210] RSP: 002b:00007fff50f1a288 EFLAGS: 00000246 ORIG_RAX: 000 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: slab: ensure slab->obj_exts is clear in a newly allocated slab page ktest recently reported crashes while running several buffered io tests with __alloc_tagging_slab_alloc_hook() at the top of the crash call stack. The signature indicates an invalid address dereference with low bits of slab->obj_exts being set. The bits were outside of the range used by page_memcg_data_flags and objext_flags and hence were not masked out by slab_obj_exts() when obtaining the pointer stored in slab->obj_exts. The typical crash log looks like this: 00510 Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010 00510 Mem abort info: 00510 ESR = 0x0000000096000045 00510 EC = 0x25: DABT (current EL), IL = 32 bits 00510 SET = 0, FnV = 0 00510 EA = 0, S1PTW = 0 00510 FSC = 0x05: level 1 translation fault 00510 Data abort info: 00510 ISV = 0, ISS = 0x00000045, ISS2 = 0x00000000 00510 CM = 0, WnR = 1, TnD = 0, TagAccess = 0 00510 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 00510 user pgtable: 4k pages, 39-bit VAs, pgdp=0000000104175000 00510 [0000000000000010] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000 00510 Internal error: Oops: 0000000096000045 [#1] SMP 00510 Modules linked in: 00510 CPU: 10 UID: 0 PID: 7692 Comm: cat Not tainted 6.15.0-rc1-ktest-g189e17946605 #19327 NONE 00510 Hardware name: linux,dummy-virt (DT) 00510 pstate: 20001005 (nzCv daif -PAN -UAO -TCO -DIT +SSBS BTYPE=--) 00510 pc : __alloc_tagging_slab_alloc_hook+0xe0/0x190 00510 lr : __kmalloc_noprof+0x150/0x310 00510 sp : ffffff80c87df6c0 00510 x29: ffffff80c87df6c0 x28: 000000000013d1ff x27: 000000000013d200 00510 x26: ffffff80c87df9e0 x25: 0000000000000000 x24: 0000000000000001 00510 x23: ffffffc08041953c x22: 000000000000004c x21: ffffff80c0002180 00510 x20: fffffffec3120840 x19: ffffff80c4821000 x18: 0000000000000000 00510 x17: fffffffec3d02f00 x16: fffffffec3d02e00 x15: fffffffec3d00700 00510 x14: fffffffec3d00600 x13: 0000000000000200 x12: 0000000000000006 00510 x11: ffffffc080bb86c0 x10: 0000000000000000 x9 : ffffffc080201e58 00510 x8 : ffffff80c4821060 x7 : 0000000000000000 x6 : 0000000055555556 00510 x5 : 0000000000000001 x4 : 0000000000000010 x3 : 0000000000000060 00510 x2 : 0000000000000000 x1 : ffffffc080f50cf8 x0 : ffffff80d801d000 00510 Call trace: 00510 __alloc_tagging_slab_alloc_hook+0xe0/0x190 (P) 00510 __kmalloc_noprof+0x150/0x310 00510 __bch2_folio_create+0x5c/0xf8 00510 bch2_folio_create+0x2c/0x40 00510 bch2_readahead+0xc0/0x460 00510 read_pages+0x7c/0x230 00510 page_cache_ra_order+0x244/0x3a8 00510 page_cache_async_ra+0x124/0x170 00510 filemap_readahead.isra.0+0x58/0xa0 00510 filemap_get_pages+0x454/0x7b0 00510 filemap_read+0xdc/0x418 00510 bch2_read_iter+0x100/0x1b0 00510 vfs_read+0x214/0x300 00510 ksys_read+0x6c/0x108 00510 __arm64_sys_read+0x20/0x30 00510 invoke_syscall.constprop.0+0x54/0xe8 00510 do_el0_svc+0x44/0xc8 00510 el0_svc+0x18/0x58 00510 el0t_64_sync_handler+0x104/0x130 00510 el0t_64_sync+0x154/0x158 00510 Code: d5384100 f9401c01 b9401aa3 b40002e1 (f8227881) 00510 ---[ end trace 0000000000000000 ]--- 00510 Kernel panic - not syncing: Oops: Fatal exception 00510 SMP: stopping secondary CPUs 00510 Kernel Offset: disabled 00510 CPU features: 0x0000,000000e0,00000410,8240500b 00510 Memory Limit: none Investigation indicates that these bits are already set when we allocate slab page and are not zeroed out after allocation. We are not yet sure why these crashes start happening only recently but regardless of the reason, not initializing a field that gets used later is wrong. Fix it by initializing slab->obj_exts during slab page allocation.

In the Linux kernel, the following vulnerability has been resolved: RDMA/cma: Fix workqueue crash in cma_netevent_work_handler struct rdma_cm_id has member "struct work_struct net_work" that is reused for enqueuing cma_netevent_work_handler()s onto cma_wq. Below crash[1] can occur if more than one call to cma_netevent_callback() occurs in quick succession, which further enqueues cma_netevent_work_handler()s for the same rdma_cm_id, overwriting any previously queued work-item(s) that was just scheduled to run i.e. there is no guarantee the queued work item may run between two successive calls to cma_netevent_callback() and the 2nd INIT_WORK would overwrite the 1st work item (for the same rdma_cm_id), despite grabbing id_table_lock during enqueue. Also drgn analysis [2] indicates the work item was likely overwritten. Fix this by moving the INIT_WORK() to __rdma_create_id(), so that it doesn't race with any existing queue_work() or its worker thread. [1] Trimmed crash stack: ============================================= BUG: kernel NULL pointer dereference, address: 0000000000000008 kworker/u256:6 ... 6.12.0-0... Workqueue: cma_netevent_work_handler [rdma_cm] (rdma_cm) RIP: 0010:process_one_work+0xba/0x31a Call Trace: worker_thread+0x266/0x3a0 kthread+0xcf/0x100 ret_from_fork+0x31/0x50 ret_from_fork_asm+0x1a/0x30 ============================================= [2] drgn crash analysis: >>> trace = prog.crashed_thread().stack_trace() >>> trace (0) crash_setup_regs (./arch/x86/include/asm/kexec.h:111:15) (1) __crash_kexec (kernel/crash_core.c:122:4) (2) panic (kernel/panic.c:399:3) (3) oops_end (arch/x86/kernel/dumpstack.c:382:3) ... (8) process_one_work (kernel/workqueue.c:3168:2) (9) process_scheduled_works (kernel/workqueue.c:3310:3) (10) worker_thread (kernel/workqueue.c:3391:4) (11) kthread (kernel/kthread.c:389:9) Line workqueue.c:3168 for this kernel version is in process_one_work(): 3168 strscpy(worker->desc, pwq->wq->name, WORKER_DESC_LEN); >>> trace[8]["work"] *(struct work_struct *)0xffff92577d0a21d8 = { .data = (atomic_long_t){ .counter = (s64)536870912, <=== Note }, .entry = (struct list_head){ .next = (struct list_head *)0xffff924d075924c0, .prev = (struct list_head *)0xffff924d075924c0, }, .func = (work_func_t)cma_netevent_work_handler+0x0 = 0xffffffffc2cec280, } Suspicion is that pwq is NULL: >>> trace[8]["pwq"] (struct pool_workqueue *)<absent> In process_one_work(), pwq is assigned from: struct pool_workqueue *pwq = get_work_pwq(work); and get_work_pwq() is: static struct pool_workqueue *get_work_pwq(struct work_struct *work) { unsigned long data = atomic_long_read(&work->data); if (data & WORK_STRUCT_PWQ) return work_struct_pwq(data); else return NULL; } WORK_STRUCT_PWQ is 0x4: >>> print(repr(prog['WORK_STRUCT_PWQ'])) Object(prog, 'enum work_flags', value=4) But work->data is 536870912 which is 0x20000000. So, get_work_pwq() returns NULL and we crash in process_one_work(): 3168 strscpy(worker->desc, pwq->wq->name, WORKER_DESC_LEN); =============================================

In the Linux kernel, the following vulnerability has been resolved: ublk: fix handling recovery & reissue in ublk_abort_queue() Commit 8284066946e6 ("ublk: grab request reference when the request is handled by userspace") doesn't grab request reference in case of recovery reissue. Then the request can be requeued & re-dispatch & failed when canceling uring command. If it is one zc request, the request can be freed before io_uring returns the zc buffer back, then cause kernel panic: [ 126.773061] BUG: kernel NULL pointer dereference, address: 00000000000000c8 [ 126.773657] #PF: supervisor read access in kernel mode [ 126.774052] #PF: error_code(0x0000) - not-present page [ 126.774455] PGD 0 P4D 0 [ 126.774698] Oops: Oops: 0000 [#1] SMP NOPTI [ 126.775034] CPU: 13 UID: 0 PID: 1612 Comm: kworker/u64:55 Not tainted 6.14.0_blk+ #182 PREEMPT(full) [ 126.775676] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-1.fc39 04/01/2014 [ 126.776275] Workqueue: iou_exit io_ring_exit_work [ 126.776651] RIP: 0010:ublk_io_release+0x14/0x130 [ublk_drv] Fixes it by always grabbing request reference for aborting the request.

In the Linux kernel, the following vulnerability has been resolved: ata: pata_pxa: Fix potential NULL pointer dereference in pxa_ata_probe() devm_ioremap() returns NULL on error. Currently, pxa_ata_probe() does not check for this case, which can result in a NULL pointer dereference. Add NULL check after devm_ioremap() to prevent this issue.

In the Linux kernel, the following vulnerability has been resolved: net: libwx: handle page_pool_dev_alloc_pages error page_pool_dev_alloc_pages could return NULL. There was a WARN_ON(!page) but it would still proceed to use the NULL pointer and then crash. This is similar to commit 001ba0902046 ("net: fec: handle page_pool_dev_alloc_pages error"). This is found by our static analysis tool KNighter.

In the Linux kernel, the following vulnerability has been resolved: iommu/mediatek: Fix NULL pointer deference in mtk_iommu_device_group Currently, mtk_iommu calls during probe iommu_device_register before the hw_list from driver data is initialized. Since iommu probing issue fix, it leads to NULL pointer dereference in mtk_iommu_device_group when hw_list is accessed with list_first_entry (not null safe). So, change the call order to ensure iommu_device_register is called after the driver data are initialized.

In the Linux kernel, the following vulnerability has been resolved: perf/dwc_pcie: fix duplicate pci_dev devices During platform_device_register, wrongly using struct device pci_dev as platform_data caused a kmemdup copy of pci_dev. Worse still, accessing the duplicated device leads to list corruption as its mutex content (e.g., list, magic) remains the same as the original.

In the Linux kernel, the following vulnerability has been resolved: soc: samsung: exynos-chipid: Add NULL pointer check in exynos_chipid_probe() soc_dev_attr->revision could be NULL, thus, a pointer check is added to prevent potential NULL pointer dereference. This is similar to the fix in commit 3027e7b15b02 ("ice: Fix some null pointer dereference issues in ice_ptp.c"). This issue is found by our static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: i3c: Add NULL pointer check in i3c_master_queue_ibi() The I3C master driver may receive an IBI from a target device that has not been probed yet. In such cases, the master calls `i3c_master_queue_ibi()` to queue an IBI work task, leading to "Unable to handle kernel read from unreadable memory" and resulting in a kernel panic. Typical IBI handling flow: 1. The I3C master scans target devices and probes their respective drivers. 2. The target device driver calls `i3c_device_request_ibi()` to enable IBI and assigns `dev->ibi = ibi`. 3. The I3C master receives an IBI from the target device and calls `i3c_master_queue_ibi()` to queue the target device driver’s IBI handler task. However, since target device events are asynchronous to the I3C probe sequence, step 3 may occur before step 2, causing `dev->ibi` to be `NULL`, leading to a kernel panic. Add a NULL pointer check in `i3c_master_queue_ibi()` to prevent accessing an uninitialized `dev->ibi`, ensuring stability.

In the Linux kernel, the following vulnerability has been resolved: mfd: ene-kb3930: Fix a potential NULL pointer dereference The off_gpios could be NULL. Add missing check in the kb3930_probe(). This is similar to the issue fixed in commit b1ba8bcb2d1f ("backlight: hx8357: Fix potential NULL pointer dereference"). This was detected by our static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: mptcp: fix NULL pointer in can_accept_new_subflow When testing valkey benchmark tool with MPTCP, the kernel panics in 'mptcp_can_accept_new_subflow' because subflow_req->msk is NULL. Call trace: mptcp_can_accept_new_subflow (./net/mptcp/subflow.c:63 (discriminator 4)) (P) subflow_syn_recv_sock (./net/mptcp/subflow.c:854) tcp_check_req (./net/ipv4/tcp_minisocks.c:863) tcp_v4_rcv (./net/ipv4/tcp_ipv4.c:2268) ip_protocol_deliver_rcu (./net/ipv4/ip_input.c:207) ip_local_deliver_finish (./net/ipv4/ip_input.c:234) ip_local_deliver (./net/ipv4/ip_input.c:254) ip_rcv_finish (./net/ipv4/ip_input.c:449) ... According to the debug log, the same req received two SYN-ACK in a very short time, very likely because the client retransmits the syn ack due to multiple reasons. Even if the packets are transmitted with a relevant time interval, they can be processed by the server on different CPUs concurrently). The 'subflow_req->msk' ownership is transferred to the subflow the first, and there will be a risk of a null pointer dereference here. This patch fixes this issue by moving the 'subflow_req->msk' under the `own_req == true` conditional. Note that the !msk check in subflow_hmac_valid() can be dropped, because the same check already exists under the own_req mpj branch where the code has been moved to.

In the Linux kernel, the following vulnerability has been resolved: net: Fix null-ptr-deref by sock_lock_init_class_and_name() and rmmod. When I ran the repro [0] and waited a few seconds, I observed two LOCKDEP splats: a warning immediately followed by a null-ptr-deref. [1] Reproduction Steps: 1) Mount CIFS 2) Add an iptables rule to drop incoming FIN packets for CIFS 3) Unmount CIFS 4) Unload the CIFS module 5) Remove the iptables rule At step 3), the CIFS module calls sock_release() for the underlying TCP socket, and it returns quickly. However, the socket remains in FIN_WAIT_1 because incoming FIN packets are dropped. At this point, the module's refcnt is 0 while the socket is still alive, so the following rmmod command succeeds. # ss -tan State Recv-Q Send-Q Local Address:Port Peer Address:Port FIN-WAIT-1 0 477 10.0.2.15:51062 10.0.0.137:445 # lsmod | grep cifs cifs 1159168 0 This highlights a discrepancy between the lifetime of the CIFS module and the underlying TCP socket. Even after CIFS calls sock_release() and it returns, the TCP socket does not die immediately in order to close the connection gracefully. While this is generally fine, it causes an issue with LOCKDEP because CIFS assigns a different lock class to the TCP socket's sk->sk_lock using sock_lock_init_class_and_name(). Once an incoming packet is processed for the socket or a timer fires, sk->sk_lock is acquired. Then, LOCKDEP checks the lock context in check_wait_context(), where hlock_class() is called to retrieve the lock class. However, since the module has already been unloaded, hlock_class() logs a warning and returns NULL, triggering the null-ptr-deref. If LOCKDEP is enabled, we must ensure that a module calling sock_lock_init_class_and_name() (CIFS, NFS, etc) cannot be unloaded while such a socket is still alive to prevent this issue. Let's hold the module reference in sock_lock_init_class_and_name() and release it when the socket is freed in sk_prot_free(). Note that sock_lock_init() clears sk->sk_owner for svc_create_socket() that calls sock_lock_init_class_and_name() for a listening socket, which clones a socket by sk_clone_lock() without GFP_ZERO. [0]: CIFS_SERVER="10.0.0.137" CIFS_PATH="//${CIFS_SERVER}/Users/Administrator/Desktop/CIFS_TEST" DEV="enp0s3" CRED="/root/WindowsCredential.txt" MNT=$(mktemp -d /tmp/XXXXXX) mount -t cifs ${CIFS_PATH} ${MNT} -o vers=3.0,credentials=${CRED},cache=none,echo_interval=1 iptables -A INPUT -s ${CIFS_SERVER} -j DROP for i in $(seq 10); do umount ${MNT} rmmod cifs sleep 1 done rm -r ${MNT} iptables -D INPUT -s ${CIFS_SERVER} -j DROP [1]: DEBUG_LOCKS_WARN_ON(1) WARNING: CPU: 10 PID: 0 at kernel/locking/lockdep.c:234 hlock_class (kernel/locking/lockdep.c:234 kernel/locking/lockdep.c:223) Modules linked in: cifs_arc4 nls_ucs2_utils cifs_md4 [last unloaded: cifs] CPU: 10 UID: 0 PID: 0 Comm: swapper/10 Not tainted 6.14.0 #36 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:hlock_class (kernel/locking/lockdep.c:234 kernel/locking/lockdep.c:223) ... Call Trace: <IRQ> __lock_acquire (kernel/locking/lockdep.c:4853 kernel/locking/lockdep.c:5178) lock_acquire (kernel/locking/lockdep.c:469 kernel/locking/lockdep.c:5853 kernel/locking/lockdep.c:5816) _raw_spin_lock_nested (kernel/locking/spinlock.c:379) tcp_v4_rcv (./include/linux/skbuff.h:1678 ./include/net/tcp.h:2547 net/ipv4/tcp_ipv4.c:2350) ... BUG: kernel NULL pointer dereference, address: 00000000000000c4 PF: supervisor read access in kernel mode PF: error_code(0x0000) - not-present page PGD 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 10 UID: 0 PID: 0 Comm: swapper/10 Tainted: G W 6.14.0 #36 Tainted: [W]=WARN Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:__lock_acquire (kernel/ ---truncated---

A null pointer dereference was addressed with improved input validation. This issue is fixed in iOS 18.3 and iPadOS 18.3, visionOS 2.3, macOS Ventura 13.7.5, iPadOS 17.7.6, macOS Sonoma 14.7.5, macOS Sequoia 15.3, tvOS 18.3. An attacker on the local network may be able to cause a denial-of-service.

The issue was addressed with improved checks. This issue is fixed in macOS Sequoia 15.4, tvOS 18.4, macOS Ventura 13.7.5, iPadOS 17.7.6, macOS Sonoma 14.7.5, iOS 18.4 and iPadOS 18.4, watchOS 11.4, visionOS 2.4. An attacker on the local network may cause an unexpected app termination.

A null pointer dereference was addressed with improved input validation. This issue is fixed in iOS 18.4 and iPadOS 18.4, macOS Sequoia 15.4, tvOS 18.4, visionOS 2.4. An attacker on the local network may be able to cause a denial-of-service.

A vulnerability was found in RefindPlusRepo RefindPlus 0.14.2.AB. It has been classified as problematic. This affects the function InternalApfsTranslateBlock of the file Library/RP_ApfsLib/RP_ApfsIo.c. The manipulation leads to null pointer dereference. It is possible to launch the attack on the local host. The patch is named 4d35125ca689a255647e9033dd60c257d26df7cb. It is recommended to apply a patch to fix this issue.

A vulnerability was found in RefindPlusRepo RefindPlus 0.14.2.AB and classified as problematic. Affected by this issue is the function GetDebugLogFile of the file Library/MemLogLib/BootLog.c. The manipulation leads to null pointer dereference. Attacking locally is a requirement. The patch is identified as d2143a1e2deefddd9b105fb7160763c4f8d47ea2. It is recommended to apply a patch to fix this issue.

DevExpress before 23.1.3 allows arbitrary TypeConverter conversion.

In xfig diagramming tool, a segmentation fault while running fig2dev allows an attacker to availability via local input manipulation via read_arcobject function.

A flaw was found in fig2dev. This vulnerability allows availability via local input manipulation via genge_itp_spline function.

A Null Pointer Dereference vulnerability in the SonicOS SSLVPN Virtual office interface allows a remote, unauthenticated attacker to crash the firewall, potentially leading to a Denial-of-Service (DoS) condition.

In Rollback Rx Professional 12.8.0.0, the driver file shieldm.sys allows local users to cause a denial of service because of a null pointer dereference from IOCtl 0x96202000.

libheif before 1.19.6 has a NULL pointer dereference in ImageItem_iden in image-items/iden.cc.

libheif before 1.19.6 has a NULL pointer dereference in ImageItem_Grid::get_decoder in image-items/grid.cc because a grid image can reference a nonexistent image item.

In the Linux kernel, the following vulnerability has been resolved: staging: gpib: Fix cb7210 pcmcia Oops The pcmcia_driver struct was still only using the old .name initialization in the drv field. This led to a NULL pointer deref Oops in strcmp called from pcmcia_register_driver. Initialize the pcmcia_driver struct name field.

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: dp: drm_err => dev_err in HPD path to avoid NULL ptr The function mtk_dp_wait_hpd_asserted() may be called before the `mtk_dp->drm_dev` pointer is assigned in mtk_dp_bridge_attach(). Specifically it can be called via this callpath: - mtk_edp_wait_hpd_asserted - [panel probe] - dp_aux_ep_probe Using "drm" level prints anywhere in this callpath causes a NULL pointer dereference. Change the error message directly in mtk_dp_wait_hpd_asserted() to dev_err() to avoid this. Also change the error messages in mtk_dp_parse_capabilities(), which is called by mtk_dp_wait_hpd_asserted(). While touching these prints, also add the error code to them to make future debugging easier.

In the Linux kernel, the following vulnerability has been resolved: remoteproc: core: Clear table_sz when rproc_shutdown There is case as below could trigger kernel dump: Use U-Boot to start remote processor(rproc) with resource table published to a fixed address by rproc. After Kernel boots up, stop the rproc, load a new firmware which doesn't have resource table ,and start rproc. When starting rproc with a firmware not have resource table, `memcpy(loaded_table, rproc->cached_table, rproc->table_sz)` will trigger dump, because rproc->cache_table is set to NULL during the last stop operation, but rproc->table_sz is still valid. This issue is found on i.MX8MP and i.MX9. Dump as below: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=000000010af63000 [0000000000000000] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP Modules linked in: CPU: 2 UID: 0 PID: 1060 Comm: sh Not tainted 6.14.0-rc7-next-20250317-dirty #38 Hardware name: NXP i.MX8MPlus EVK board (DT) pstate: a0000005 (NzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __pi_memcpy_generic+0x110/0x22c lr : rproc_start+0x88/0x1e0 Call trace: __pi_memcpy_generic+0x110/0x22c (P) rproc_boot+0x198/0x57c state_store+0x40/0x104 dev_attr_store+0x18/0x2c sysfs_kf_write+0x7c/0x94 kernfs_fop_write_iter+0x120/0x1cc vfs_write+0x240/0x378 ksys_write+0x70/0x108 __arm64_sys_write+0x1c/0x28 invoke_syscall+0x48/0x10c el0_svc_common.constprop.0+0xc0/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x30/0xcc el0t_64_sync_handler+0x10c/0x138 el0t_64_sync+0x198/0x19c Clear rproc->table_sz to address the issue.

In the Linux kernel, the following vulnerability has been resolved: x86/resctrl: Fix allocation of cleanest CLOSID on platforms with no monitors Commit 6eac36bb9eb0 ("x86/resctrl: Allocate the cleanest CLOSID by searching closid_num_dirty_rmid") added logic that causes resctrl to search for the CLOSID with the fewest dirty cache lines when creating a new control group, if requested by the arch code. This depends on the values read from the llc_occupancy counters. The logic is applicable to architectures where the CLOSID effectively forms part of the monitoring identifier and so do not allow complete freedom to choose an unused monitoring identifier for a given CLOSID. This support missed that some platforms may not have these counters. This causes a NULL pointer dereference when creating a new control group as the array was not allocated by dom_data_init(). As this feature isn't necessary on platforms that don't have cache occupancy monitors, add this to the check that occurs when a new control group is allocated.

In the Linux kernel, the following vulnerability has been resolved: sfc: fix NULL dereferences in ef100_process_design_param() Since cited commit, ef100_probe_main() and hence also ef100_check_design_params() run before efx->net_dev is created; consequently, we cannot netif_set_tso_max_size() or _segs() at this point. Move those netif calls to ef100_probe_netdev(), and also replace netif_err within the design params code with pci_err.

In the Linux kernel, the following vulnerability has been resolved: can: dev: can_get_echo_skb(): prevent call to kfree_skb() in hard IRQ context If a driver calls can_get_echo_skb() during a hardware IRQ (which is often, but not always, the case), the 'WARN_ON(in_irq)' in net/core/skbuff.c#skb_release_head_state() might be triggered, under network congestion circumstances, together with the potential risk of a NULL pointer dereference. The root cause of this issue is the call to kfree_skb() instead of dev_kfree_skb_irq() in net/core/dev.c#enqueue_to_backlog(). This patch prevents the skb to be freed within the call to netif_rx() by incrementing its reference count with skb_get(). The skb is finally freed by one of the in-irq-context safe functions: dev_consume_skb_any() or dev_kfree_skb_any(). The "any" version is used because some drivers might call can_get_echo_skb() in a normal context. The reason for this issue to occur is that initially, in the core network stack, loopback skb were not supposed to be received in hardware IRQ context. The CAN stack is an exeption. This bug was previously reported back in 2017 in [1] but the proposed patch never got accepted. While [1] directly modifies net/core/dev.c, we try to propose here a smoother modification local to CAN network stack (the assumption behind is that only CAN devices are affected by this issue). [1] http://lore.kernel.org/r/57a3ffb6-3309-3ad5-5a34-e93c3fe3614d@cetitec.com

SoftEtherVPN is a an open-source cross-platform multi-protocol VPN Program. Versions 5.02.5184 to 5.02.5187 are vulnerable to NULL dereference in `DeleteIPv6DefaultRouterInRA` called by `StorePacket`. Before dereferencing, `DeleteIPv6DefaultRouterInRA` does not account for `ParsePacket` returning NULL, resulting in the program crashing. A patched version does not exist at this time.

In the Linux kernel, the following vulnerability has been resolved: cpufreq/amd-pstate: Add missing NULL ptr check in amd_pstate_update Check if policy is NULL before dereferencing it in amd_pstate_update.

In the Linux kernel, the following vulnerability has been resolved: thermal: int340x: Add NULL check for adev Not all devices have an ACPI companion fwnode, so adev might be NULL. This is similar to the commit cd2fd6eab480 ("platform/x86: int3472: Check for adev == NULL"). Add a check for adev not being set and return -ENODEV in that case to avoid a possible NULL pointer deref in int3402_thermal_probe(). Note, under the same directory, int3400_thermal_probe() has such a check. [ rjw: Subject edit, added Fixes: ]

In the Linux kernel, the following vulnerability has been resolved: dlm: prevent NPD when writing a positive value to event_done do_uevent returns the value written to event_done. In case it is a positive value, new_lockspace would undo all the work, and lockspace would not be set. __dlm_new_lockspace, however, would treat that positive value as a success due to commit 8511a2728ab8 ("dlm: fix use count with multiple joins"). Down the line, device_create_lockspace would pass that NULL lockspace to dlm_find_lockspace_local, leading to a NULL pointer dereference. Treating such positive values as successes prevents the problem. Given this has been broken for so long, this is unlikely to break userspace expectations.

In the Linux kernel, the following vulnerability has been resolved: net: fix NULL pointer dereference in l3mdev_l3_rcv When delete l3s ipvlan: ip link del link eth0 ipvlan1 type ipvlan mode l3s This may cause a null pointer dereference: Call trace: ip_rcv_finish+0x48/0xd0 ip_rcv+0x5c/0x100 __netif_receive_skb_one_core+0x64/0xb0 __netif_receive_skb+0x20/0x80 process_backlog+0xb4/0x204 napi_poll+0xe8/0x294 net_rx_action+0xd8/0x22c __do_softirq+0x12c/0x354 This is because l3mdev_l3_rcv() visit dev->l3mdev_ops after ipvlan_l3s_unregister() assign the dev->l3mdev_ops to NULL. The process like this: (CPU1) | (CPU2) l3mdev_l3_rcv() | check dev->priv_flags: | master = skb->dev; | | | ipvlan_l3s_unregister() | set dev->priv_flags | dev->l3mdev_ops = NULL; | visit master->l3mdev_ops | To avoid this by do not set dev->l3mdev_ops when unregister l3s ipvlan.

In the Linux kernel, the following vulnerability has been resolved: drm: xlnx: zynqmp_dpsub: Add NULL check in zynqmp_audio_init devm_kasprintf() calls can return null pointers on failure. But some return values were not checked in zynqmp_audio_init(). Add NULL check in zynqmp_audio_init(), avoid referencing null pointers in the subsequent code.

In the Linux kernel, the following vulnerability has been resolved: powerpc/perf: Fix ref-counting on the PMU 'vpa_pmu' Commit 176cda0619b6 ("powerpc/perf: Add perf interface to expose vpa counters") introduced 'vpa_pmu' to expose Book3s-HV nested APIv2 provided L1<->L2 context switch latency counters to L1 user-space via perf-events. However the newly introduced PMU named 'vpa_pmu' doesn't assign ownership of the PMU to the module 'vpa_pmu'. Consequently the module 'vpa_pmu' can be unloaded while one of the perf-events are still active, which can lead to kernel oops and panic of the form below on a Pseries-LPAR: BUG: Kernel NULL pointer dereference on read at 0x00000058 <snip> NIP [c000000000506cb8] event_sched_out+0x40/0x258 LR [c00000000050e8a4] __perf_remove_from_context+0x7c/0x2b0 Call Trace: [c00000025fc3fc30] [c00000025f8457a8] 0xc00000025f8457a8 (unreliable) [c00000025fc3fc80] [fffffffffffffee0] 0xfffffffffffffee0 [c00000025fc3fcd0] [c000000000501e70] event_function+0xa8/0x120 <snip> Kernel panic - not syncing: Aiee, killing interrupt handler! Fix this by adding the module ownership to 'vpa_pmu' so that the module 'vpa_pmu' is ref-counted and prevented from being unloaded when perf-events are initialized.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: avoid NPD when ASIC does not support DMUB ctx->dmub_srv will de NULL if the ASIC does not support DMUB, which is tested in dm_dmub_sw_init. However, it will be dereferenced in dmub_hw_lock_mgr_cmd if should_use_dmub_lock returns true. This has been the case since dmub support has been added for PSR1. Fix this by checking for dmub_srv in should_use_dmub_lock. [ 37.440832] BUG: kernel NULL pointer dereference, address: 0000000000000058 [ 37.447808] #PF: supervisor read access in kernel mode [ 37.452959] #PF: error_code(0x0000) - not-present page [ 37.458112] PGD 0 P4D 0 [ 37.460662] Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI [ 37.465553] CPU: 2 UID: 1000 PID: 1745 Comm: DrmThread Not tainted 6.14.0-rc1-00003-gd62e938120f0 #23 99720e1cb1e0fc4773b8513150932a07de3c6e88 [ 37.478324] Hardware name: Google Morphius/Morphius, BIOS Google_Morphius.13434.858.0 10/26/2023 [ 37.487103] RIP: 0010:dmub_hw_lock_mgr_cmd+0x77/0xb0 [ 37.492074] Code: 44 24 0e 00 00 00 00 48 c7 04 24 45 00 00 0c 40 88 74 24 0d 0f b6 02 88 44 24 0c 8b 01 89 44 24 08 85 f6 75 05 c6 44 24 0e 01 <48> 8b 7f 58 48 89 e6 ba 01 00 00 00 e8 08 3c 2a 00 65 48 8b 04 5 [ 37.510822] RSP: 0018:ffff969442853300 EFLAGS: 00010202 [ 37.516052] RAX: 0000000000000000 RBX: ffff92db03000000 RCX: ffff969442853358 [ 37.523185] RDX: ffff969442853368 RSI: 0000000000000001 RDI: 0000000000000000 [ 37.530322] RBP: 0000000000000001 R08: 00000000000004a7 R09: 00000000000004a5 [ 37.537453] R10: 0000000000000476 R11: 0000000000000062 R12: ffff92db0ade8000 [ 37.544589] R13: ffff92da01180ae0 R14: ffff92da011802a8 R15: ffff92db03000000 [ 37.551725] FS: 0000784a9cdfc6c0(0000) GS:ffff92db2af00000(0000) knlGS:0000000000000000 [ 37.559814] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 37.565562] CR2: 0000000000000058 CR3: 0000000112b1c000 CR4: 00000000003506f0 [ 37.572697] Call Trace: [ 37.575152] <TASK> [ 37.577258] ? __die_body+0x66/0xb0 [ 37.580756] ? page_fault_oops+0x3e7/0x4a0 [ 37.584861] ? exc_page_fault+0x3e/0xe0 [ 37.588706] ? exc_page_fault+0x5c/0xe0 [ 37.592550] ? asm_exc_page_fault+0x22/0x30 [ 37.596742] ? dmub_hw_lock_mgr_cmd+0x77/0xb0 [ 37.601107] dcn10_cursor_lock+0x1e1/0x240 [ 37.605211] program_cursor_attributes+0x81/0x190 [ 37.609923] commit_planes_for_stream+0x998/0x1ef0 [ 37.614722] update_planes_and_stream_v2+0x41e/0x5c0 [ 37.619703] dc_update_planes_and_stream+0x78/0x140 [ 37.624588] amdgpu_dm_atomic_commit_tail+0x4362/0x49f0 [ 37.629832] ? srso_return_thunk+0x5/0x5f [ 37.633847] ? mark_held_locks+0x6d/0xd0 [ 37.637774] ? _raw_spin_unlock_irq+0x24/0x50 [ 37.642135] ? srso_return_thunk+0x5/0x5f [ 37.646148] ? lockdep_hardirqs_on+0x95/0x150 [ 37.650510] ? srso_return_thunk+0x5/0x5f [ 37.654522] ? _raw_spin_unlock_irq+0x2f/0x50 [ 37.658883] ? srso_return_thunk+0x5/0x5f [ 37.662897] ? wait_for_common+0x186/0x1c0 [ 37.666998] ? srso_return_thunk+0x5/0x5f [ 37.671009] ? drm_crtc_next_vblank_start+0xc3/0x170 [ 37.675983] commit_tail+0xf5/0x1c0 [ 37.679478] drm_atomic_helper_commit+0x2a2/0x2b0 [ 37.684186] drm_atomic_commit+0xd6/0x100 [ 37.688199] ? __cfi___drm_printfn_info+0x10/0x10 [ 37.692911] drm_atomic_helper_update_plane+0xe5/0x130 [ 37.698054] drm_mode_cursor_common+0x501/0x670 [ 37.702600] ? __cfi_drm_mode_cursor_ioctl+0x10/0x10 [ 37.707572] drm_mode_cursor_ioctl+0x48/0x70 [ 37.711851] drm_ioctl_kernel+0xf2/0x150 [ 37.715781] drm_ioctl+0x363/0x590 [ 37.719189] ? __cfi_drm_mode_cursor_ioctl+0x10/0x10 [ 37.724165] amdgpu_drm_ioctl+0x41/0x80 [ 37.728013] __se_sys_ioctl+0x7f/0xd0 [ 37.731685] do_syscall_64+0x87/0x100 [ 37.735355] ? vma_end_read+0x12/0xe0 [ 37.739024] ? srso_return_thunk+0x5/0x5f [ 37.743041] ? find_held_lock+0x47/0xf0 [ 37.746884] ? vma_end_read+0x12/0xe0 [ 37.750552] ? srso_return_thunk+0x5/0 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: PCI: Fix NULL dereference in SR-IOV VF creation error path Clean up when virtfn setup fails to prevent NULL pointer dereference during device removal. The kernel oops below occurred due to incorrect error handling flow when pci_setup_device() fails. Add pci_iov_scan_device(), which handles virtfn allocation and setup and cleans up if pci_setup_device() fails, so pci_iov_add_virtfn() doesn't need to call pci_stop_and_remove_bus_device(). This prevents accessing partially initialized virtfn devices during removal. BUG: kernel NULL pointer dereference, address: 00000000000000d0 RIP: 0010:device_del+0x3d/0x3d0 Call Trace: pci_remove_bus_device+0x7c/0x100 pci_iov_add_virtfn+0xfa/0x200 sriov_enable+0x208/0x420 mlx5_core_sriov_configure+0x6a/0x160 [mlx5_core] sriov_numvfs_store+0xae/0x1a0 [bhelgaas: commit log, return ERR_PTR(-ENOMEM) directly]

In the Linux kernel, the following vulnerability has been resolved: RDMA/core: Don't expose hw_counters outside of init net namespace Commit 467f432a521a ("RDMA/core: Split port and device counter sysfs attributes") accidentally almost exposed hw counters to non-init net namespaces. It didn't expose them fully, as an attempt to read any of those counters leads to a crash like this one: [42021.807566] BUG: kernel NULL pointer dereference, address: 0000000000000028 [42021.814463] #PF: supervisor read access in kernel mode [42021.819549] #PF: error_code(0x0000) - not-present page [42021.824636] PGD 0 P4D 0 [42021.827145] Oops: 0000 [#1] SMP PTI [42021.830598] CPU: 82 PID: 2843922 Comm: switchto-defaul Kdump: loaded Tainted: G S W I XXX [42021.841697] Hardware name: XXX [42021.849619] RIP: 0010:hw_stat_device_show+0x1e/0x40 [ib_core] [42021.855362] Code: 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 0f 1f 44 00 00 49 89 d0 4c 8b 5e 20 48 8b 8f b8 04 00 00 48 81 c7 f0 fa ff ff <48> 8b 41 28 48 29 ce 48 83 c6 d0 48 c1 ee 04 69 d6 ab aa aa aa 48 [42021.873931] RSP: 0018:ffff97fe90f03da0 EFLAGS: 00010287 [42021.879108] RAX: ffff9406988a8c60 RBX: ffff940e1072d438 RCX: 0000000000000000 [42021.886169] RDX: ffff94085f1aa000 RSI: ffff93c6cbbdbcb0 RDI: ffff940c7517aef0 [42021.893230] RBP: ffff97fe90f03e70 R08: ffff94085f1aa000 R09: 0000000000000000 [42021.900294] R10: ffff94085f1aa000 R11: ffffffffc0775680 R12: ffffffff87ca2530 [42021.907355] R13: ffff940651602840 R14: ffff93c6cbbdbcb0 R15: ffff94085f1aa000 [42021.914418] FS: 00007fda1a3b9700(0000) GS:ffff94453fb80000(0000) knlGS:0000000000000000 [42021.922423] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [42021.928130] CR2: 0000000000000028 CR3: 00000042dcfb8003 CR4: 00000000003726f0 [42021.935194] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [42021.942257] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [42021.949324] Call Trace: [42021.951756] <TASK> [42021.953842] [<ffffffff86c58674>] ? show_regs+0x64/0x70 [42021.959030] [<ffffffff86c58468>] ? __die+0x78/0xc0 [42021.963874] [<ffffffff86c9ef75>] ? page_fault_oops+0x2b5/0x3b0 [42021.969749] [<ffffffff87674b92>] ? exc_page_fault+0x1a2/0x3c0 [42021.975549] [<ffffffff87801326>] ? asm_exc_page_fault+0x26/0x30 [42021.981517] [<ffffffffc0775680>] ? __pfx_show_hw_stats+0x10/0x10 [ib_core] [42021.988482] [<ffffffffc077564e>] ? hw_stat_device_show+0x1e/0x40 [ib_core] [42021.995438] [<ffffffff86ac7f8e>] dev_attr_show+0x1e/0x50 [42022.000803] [<ffffffff86a3eeb1>] sysfs_kf_seq_show+0x81/0xe0 [42022.006508] [<ffffffff86a11134>] seq_read_iter+0xf4/0x410 [42022.011954] [<ffffffff869f4b2e>] vfs_read+0x16e/0x2f0 [42022.017058] [<ffffffff869f50ee>] ksys_read+0x6e/0xe0 [42022.022073] [<ffffffff8766f1ca>] do_syscall_64+0x6a/0xa0 [42022.027441] [<ffffffff8780013b>] entry_SYSCALL_64_after_hwframe+0x78/0xe2 The problem can be reproduced using the following steps: ip netns add foo ip netns exec foo bash cat /sys/class/infiniband/mlx4_0/hw_counters/* The panic occurs because of casting the device pointer into an ib_device pointer using container_of() in hw_stat_device_show() is wrong and leads to a memory corruption. However the real problem is that hw counters should never been exposed outside of the non-init net namespace. Fix this by saving the index of the corresponding attribute group (it might be 1 or 2 depending on the presence of driver-specific attributes) and zeroing the pointer to hw_counters group for compat devices during the initialization. With this fix applied hw_counters are not available in a non-init net namespace: find /sys/class/infiniband/mlx4_0/ -name hw_counters /sys/class/infiniband/mlx4_0/ports/1/hw_counters /sys/class/infiniband/mlx4_0/ports/2/hw_counters /sys/class/infiniband/mlx4_0/hw_counters ip netns add foo ip netns exec foo bash find /sys/class/infiniband/mlx4_0/ -name hw_counters

In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Fix mlx5_poll_one() cur_qp update flow When cur_qp isn't NULL, in order to avoid fetching the QP from the radix tree again we check if the next cqe QP is identical to the one we already have. The bug however is that we are checking if the QP is identical by checking the QP number inside the CQE against the QP number inside the mlx5_ib_qp, but that's wrong since the QP number from the CQE is from FW so it should be matched against mlx5_core_qp which is our FW QP number. Otherwise we could use the wrong QP when handling a CQE which could cause the kernel trace below. This issue is mainly noticeable over QPs 0 & 1, since for now they are the only QPs in our driver whereas the QP number inside mlx5_ib_qp doesn't match the QP number inside mlx5_core_qp. BUG: kernel NULL pointer dereference, address: 0000000000000012 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP CPU: 0 UID: 0 PID: 7927 Comm: kworker/u62:1 Not tainted 6.14.0-rc3+ #189 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 Workqueue: ib-comp-unb-wq ib_cq_poll_work [ib_core] RIP: 0010:mlx5_ib_poll_cq+0x4c7/0xd90 [mlx5_ib] Code: 03 00 00 8d 58 ff 21 cb 66 39 d3 74 39 48 c7 c7 3c 89 6e a0 0f b7 db e8 b7 d2 b3 e0 49 8b 86 60 03 00 00 48 c7 c7 4a 89 6e a0 <0f> b7 5c 98 02 e8 9f d2 b3 e0 41 0f b7 86 78 03 00 00 83 e8 01 21 RSP: 0018:ffff88810511bd60 EFLAGS: 00010046 RAX: 0000000000000010 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff88885fa1b3c0 RDI: ffffffffa06e894a RBP: 00000000000000b0 R08: 0000000000000000 R09: ffff88810511bc10 R10: 0000000000000001 R11: 0000000000000001 R12: ffff88810d593000 R13: ffff88810e579108 R14: ffff888105146000 R15: 00000000000000b0 FS: 0000000000000000(0000) GS:ffff88885fa00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000012 CR3: 00000001077e6001 CR4: 0000000000370eb0 Call Trace: <TASK> ? __die+0x20/0x60 ? page_fault_oops+0x150/0x3e0 ? exc_page_fault+0x74/0x130 ? asm_exc_page_fault+0x22/0x30 ? mlx5_ib_poll_cq+0x4c7/0xd90 [mlx5_ib] __ib_process_cq+0x5a/0x150 [ib_core] ib_cq_poll_work+0x31/0x90 [ib_core] process_one_work+0x169/0x320 worker_thread+0x288/0x3a0 ? work_busy+0xb0/0xb0 kthread+0xd7/0x1f0 ? kthreads_online_cpu+0x130/0x130 ? kthreads_online_cpu+0x130/0x130 ret_from_fork+0x2d/0x50 ? kthreads_online_cpu+0x130/0x130 ret_from_fork_asm+0x11/0x20 </TASK>

In the Linux kernel, the following vulnerability has been resolved: w1: fix NULL pointer dereference in probe The w1_uart_probe() function calls w1_uart_serdev_open() (which includes devm_serdev_device_open()) before setting the client ops via serdev_device_set_client_ops(). This ordering can trigger a NULL pointer dereference in the serdev controller's receive_buf handler, as it assumes serdev->ops is valid when SERPORT_ACTIVE is set. This is similar to the issue fixed in commit 5e700b384ec1 ("platform/chrome: cros_ec_uart: properly fix race condition") where devm_serdev_device_open() was called before fully initializing the device. Fix the race by ensuring client ops are set before enabling the port via w1_uart_serdev_open().

In the Linux kernel, the following vulnerability has been resolved: fs/9p: fix NULL pointer dereference on mkdir When a 9p tree was mounted with option 'posixacl', parent directory had a default ACL set for its subdirectories, e.g.: setfacl -m default:group:simpsons:rwx parentdir then creating a subdirectory crashed 9p client, as v9fs_fid_add() call in function v9fs_vfs_mkdir_dotl() sets the passed 'fid' pointer to NULL (since dafbe689736) even though the subsequent v9fs_set_create_acl() call expects a valid non-NULL 'fid' pointer: [ 37.273191] BUG: kernel NULL pointer dereference, address: 0000000000000000 ... [ 37.322338] Call Trace: [ 37.323043] <TASK> [ 37.323621] ? __die (arch/x86/kernel/dumpstack.c:421 arch/x86/kernel/dumpstack.c:434) [ 37.324448] ? page_fault_oops (arch/x86/mm/fault.c:714) [ 37.325532] ? search_module_extables (kernel/module/main.c:3733) [ 37.326742] ? p9_client_walk (net/9p/client.c:1165) 9pnet [ 37.328006] ? search_bpf_extables (kernel/bpf/core.c:804) [ 37.329142] ? exc_page_fault (./arch/x86/include/asm/paravirt.h:686 arch/x86/mm/fault.c:1488 arch/x86/mm/fault.c:1538) [ 37.330196] ? asm_exc_page_fault (./arch/x86/include/asm/idtentry.h:574) [ 37.331330] ? p9_client_walk (net/9p/client.c:1165) 9pnet [ 37.332562] ? v9fs_fid_xattr_get (fs/9p/xattr.c:30) 9p [ 37.333824] v9fs_fid_xattr_set (fs/9p/fid.h:23 fs/9p/xattr.c:121) 9p [ 37.335077] v9fs_set_acl (fs/9p/acl.c:276) 9p [ 37.336112] v9fs_set_create_acl (fs/9p/acl.c:307) 9p [ 37.337326] v9fs_vfs_mkdir_dotl (fs/9p/vfs_inode_dotl.c:411) 9p [ 37.338590] vfs_mkdir (fs/namei.c:4313) [ 37.339535] do_mkdirat (fs/namei.c:4336) [ 37.340465] __x64_sys_mkdir (fs/namei.c:4354) [ 37.341455] do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83) [ 37.342447] entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) Fix this by simply swapping the sequence of these two calls in v9fs_vfs_mkdir_dotl(), i.e. calling v9fs_set_create_acl() before v9fs_fid_add().

In the Linux kernel, the following vulnerability has been resolved: ASoC: imx-card: Add NULL check in imx_card_probe() devm_kasprintf() returns NULL when memory allocation fails. Currently, imx_card_probe() does not check for this case, which results in a NULL pointer dereference. Add NULL check after devm_kasprintf() to prevent this issue.

In the Linux kernel, the following vulnerability has been resolved: idpf: fix adapter NULL pointer dereference on reboot With SRIOV enabled, idpf ends up calling into idpf_remove() twice. First via idpf_shutdown() and then again when idpf_remove() calls into sriov_disable(), because the VF devices use the idpf driver, hence the same remove routine. When that happens, it is possible for the adapter to be NULL from the first call to idpf_remove(), leading to a NULL pointer dereference. echo 1 > /sys/class/net/<netif>/device/sriov_numvfs reboot BUG: kernel NULL pointer dereference, address: 0000000000000020 ... RIP: 0010:idpf_remove+0x22/0x1f0 [idpf] ... ? idpf_remove+0x22/0x1f0 [idpf] ? idpf_remove+0x1e4/0x1f0 [idpf] pci_device_remove+0x3f/0xb0 device_release_driver_internal+0x19f/0x200 pci_stop_bus_device+0x6d/0x90 pci_stop_and_remove_bus_device+0x12/0x20 pci_iov_remove_virtfn+0xbe/0x120 sriov_disable+0x34/0xe0 idpf_sriov_configure+0x58/0x140 [idpf] idpf_remove+0x1b9/0x1f0 [idpf] idpf_shutdown+0x12/0x30 [idpf] pci_device_shutdown+0x35/0x60 device_shutdown+0x156/0x200 ... Replace the direct idpf_remove() call in idpf_shutdown() with idpf_vc_core_deinit() and idpf_deinit_dflt_mbx(), which perform the bulk of the cleanup, such as stopping the init task, freeing IRQs, destroying the vports and freeing the mailbox. This avoids the calls to sriov_disable() in addition to a small netdev cleanup, and destroying workqueues, which don't seem to be required on shutdown.

In the Linux kernel, the following vulnerability has been resolved: netlabel: Fix NULL pointer exception caused by CALIPSO on IPv4 sockets When calling netlbl_conn_setattr(), addr->sa_family is used to determine the function behavior. If sk is an IPv4 socket, but the connect function is called with an IPv6 address, the function calipso_sock_setattr() is triggered. Inside this function, the following code is executed: sk_fullsock(__sk) ? inet_sk(__sk)->pinet6 : NULL; Since sk is an IPv4 socket, pinet6 is NULL, leading to a null pointer dereference. This patch fixes the issue by checking if inet6_sk(sk) returns a NULL pointer before accessing pinet6.