In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Wait for io return on terminate rport System crash due to use after free. Current code allows terminate_rport_io to exit before making sure all IOs has returned. For FCP-2 device, IO's can hang on in HW because driver has not tear down the session in FW at first sign of cable pull. When dev_loss_tmo timer pops, terminate_rport_io is called and upper layer is about to free various resources. Terminate_rport_io trigger qla to do the final cleanup, but the cleanup might not be fast enough where it leave qla still holding on to the same resource. Wait for IO's to return to upper layer before resources are freed.

In the Linux kernel, the following vulnerability has been resolved: pstore/ram: Check start of empty przs during init After commit 30696378f68a ("pstore/ram: Do not treat empty buffers as valid"), initialization would assume a prz was valid after seeing that the buffer_size is zero (regardless of the buffer start position). This unchecked start value means it could be outside the bounds of the buffer, leading to future access panics when written to: sysdump_panic_event+0x3b4/0x5b8 atomic_notifier_call_chain+0x54/0x90 panic+0x1c8/0x42c die+0x29c/0x2a8 die_kernel_fault+0x68/0x78 __do_kernel_fault+0x1c4/0x1e0 do_bad_area+0x40/0x100 do_translation_fault+0x68/0x80 do_mem_abort+0x68/0xf8 el1_da+0x1c/0xc0 __raw_writeb+0x38/0x174 __memcpy_toio+0x40/0xac persistent_ram_update+0x44/0x12c persistent_ram_write+0x1a8/0x1b8 ramoops_pstore_write+0x198/0x1e8 pstore_console_write+0x94/0xe0 ... To avoid this, also check if the prz start is 0 during the initialization phase. If not, the next prz sanity check case will discover it (start > size) and zap the buffer back to a sane state. [kees: update commit log with backtrace and clarifications]

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Collect command failures data only for known commands DEVX can issue a general command, which is not used by mlx5 driver. In case such command is failed, mlx5 is trying to collect the failure data, However, mlx5 doesn't create a storage for this command, since mlx5 doesn't use it. This lead to array-index-out-of-bounds error. Fix it by checking whether the command is known before collecting the failure data.

In the Linux kernel, the following vulnerability has been resolved: sctp: fix a potential overflow in sctp_ifwdtsn_skip Currently, when traversing ifwdtsn skips with _sctp_walk_ifwdtsn, it only checks the pos against the end of the chunk. However, the data left for the last pos may be < sizeof(struct sctp_ifwdtsn_skip), and dereference it as struct sctp_ifwdtsn_skip may cause coverflow. This patch fixes it by checking the pos against "the end of the chunk - sizeof(struct sctp_ifwdtsn_skip)" in sctp_ifwdtsn_skip, similar to sctp_fwdtsn_skip.

In the Linux kernel, the following vulnerability has been resolved: crypto: seqiv - Handle EBUSY correctly As it is seqiv only handles the special return value of EINPROGERSS, which means that in all other cases it will free data related to the request. However, as the caller of seqiv may specify MAY_BACKLOG, we also need to expect EBUSY and treat it in the same way. Otherwise backlogged requests will trigger a use-after-free.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_conn: fail SCO/ISO via hci_conn_failed if ACL gone early Not calling hci_(dis)connect_cfm before deleting conn referred to by a socket generally results to use-after-free. When cleaning up SCO connections when the parent ACL is deleted too early, use hci_conn_failed to do the connection cleanup properly. We also need to clean up ISO connections in a similar situation when connecting has started but LE Create CIS is not yet sent, so do it too here.

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: Clean dangling pointer on bind error path mtk_drm_bind() can fail, in which case drm_dev_put() is called, destroying the drm_device object. However a pointer to it was still being held in the private object, and that pointer would be passed along to DRM in mtk_drm_sys_prepare() if a suspend were triggered at that point, resulting in a panic. Clean the pointer when destroying the object in the error path to prevent this from happening.

In the Linux kernel, the following vulnerability has been resolved: ACPICA: Add AML_NO_OPERAND_RESOLVE flag to Timer ACPICA commit 90310989a0790032f5a0140741ff09b545af4bc5 According to the ACPI specification 19.6.134, no argument is required to be passed for ASL Timer instruction. For taking care of no argument, AML_NO_OPERAND_RESOLVE flag is added to ASL Timer instruction opcode. When ASL timer instruction interpreted by ACPI interpreter, getting error. After adding AML_NO_OPERAND_RESOLVE flag to ASL Timer instruction opcode, issue is not observed. ============================================================= UBSAN: array-index-out-of-bounds in acpica/dswexec.c:401:12 index -1 is out of range for type 'union acpi_operand_object *[9]' CPU: 37 PID: 1678 Comm: cat Not tainted 6.0.0-dev-th500-6.0.y-1+bcf8c46459e407-generic-64k HW name: NVIDIA BIOS v1.1.1-d7acbfc-dirty 12/19/2022 Call trace: dump_backtrace+0xe0/0x130 show_stack+0x20/0x60 dump_stack_lvl+0x68/0x84 dump_stack+0x18/0x34 ubsan_epilogue+0x10/0x50 __ubsan_handle_out_of_bounds+0x80/0x90 acpi_ds_exec_end_op+0x1bc/0x6d8 acpi_ps_parse_loop+0x57c/0x618 acpi_ps_parse_aml+0x1e0/0x4b4 acpi_ps_execute_method+0x24c/0x2b8 acpi_ns_evaluate+0x3a8/0x4bc acpi_evaluate_object+0x15c/0x37c acpi_evaluate_integer+0x54/0x15c show_power+0x8c/0x12c [acpi_power_meter]

In the Linux kernel, the following vulnerability has been resolved: mlx5: fix possible ptp queue fifo use-after-free Fifo indexes are not checked during pop operations and it leads to potential use-after-free when poping from empty queue. Such case was possible during re-sync action. WARN_ON_ONCE covers future cases. There were out-of-order cqe spotted which lead to drain of the queue and use-after-free because of lack of fifo pointers check. Special check and counter are added to avoid resync operation if SKB could not exist in the fifo because of OOO cqe (skb_id must be between consumer and producer index).

In the Linux kernel, the following vulnerability has been resolved: xsk: Fix xsk_diag use-after-free error during socket cleanup Fix a use-after-free error that is possible if the xsk_diag interface is used after the socket has been unbound from the device. This can happen either due to the socket being closed or the device disappearing. In the early days of AF_XDP, the way we tested that a socket was not bound to a device was to simply check if the netdevice pointer in the xsk socket structure was NULL. Later, a better system was introduced by having an explicit state variable in the xsk socket struct. For example, the state of a socket that is on the way to being closed and has been unbound from the device is XSK_UNBOUND. The commit in the Fixes tag below deleted the old way of signalling that a socket is unbound, setting dev to NULL. This in the belief that all code using the old way had been exterminated. That was unfortunately not true as the xsk diagnostics code was still using the old way and thus does not work as intended when a socket is going down. Fix this by introducing a test against the state variable. If the socket is in the state XSK_UNBOUND, simply abort the diagnostic's netlink operation.

In the Linux kernel, the following vulnerability has been resolved: HID: mcp-2221: prevent UAF in delayed work If the device is plugged/unplugged without giving time for mcp_init_work() to complete, we might kick in the devm free code path and thus have unavailable struct mcp_2221 while in delayed work. Canceling the delayed_work item is enough to solve the issue, because cancel_delayed_work_sync will prevent the work item to requeue itself.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/gfx: disable gfx9 cp_ecc_error_irq only when enabling legacy gfx ras gfx9 cp_ecc_error_irq is only enabled when legacy gfx ras is assert. So in gfx_v9_0_hw_fini, interrupt disablement for cp_ecc_error_irq should be executed under such condition, otherwise, an amdgpu_irq_put calltrace will occur. [ 7283.170322] RIP: 0010:amdgpu_irq_put+0x45/0x70 [amdgpu] [ 7283.170964] RSP: 0018:ffff9a5fc3967d00 EFLAGS: 00010246 [ 7283.170967] RAX: ffff98d88afd3040 RBX: ffff98d89da20000 RCX: 0000000000000000 [ 7283.170969] RDX: 0000000000000000 RSI: ffff98d89da2bef8 RDI: ffff98d89da20000 [ 7283.170971] RBP: ffff98d89da20000 R08: ffff98d89da2ca18 R09: 0000000000000006 [ 7283.170973] R10: ffffd5764243c008 R11: 0000000000000000 R12: 0000000000001050 [ 7283.170975] R13: ffff98d89da38978 R14: ffffffff999ae15a R15: ffff98d880130105 [ 7283.170978] FS: 0000000000000000(0000) GS:ffff98d996f00000(0000) knlGS:0000000000000000 [ 7283.170981] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 7283.170983] CR2: 00000000f7a9d178 CR3: 00000001c42ea000 CR4: 00000000003506e0 [ 7283.170986] Call Trace: [ 7283.170988] <TASK> [ 7283.170989] gfx_v9_0_hw_fini+0x1c/0x6d0 [amdgpu] [ 7283.171655] amdgpu_device_ip_suspend_phase2+0x101/0x1a0 [amdgpu] [ 7283.172245] amdgpu_device_suspend+0x103/0x180 [amdgpu] [ 7283.172823] amdgpu_pmops_freeze+0x21/0x60 [amdgpu] [ 7283.173412] pci_pm_freeze+0x54/0xc0 [ 7283.173419] ? __pfx_pci_pm_freeze+0x10/0x10 [ 7283.173425] dpm_run_callback+0x98/0x200 [ 7283.173430] __device_suspend+0x164/0x5f0 v2: drop gfx11 as it's fixed in a different solution by retiring cp_ecc_irq funcs(Hawking)

In the Linux kernel, the following vulnerability has been resolved: lib: cpu_rmap: Avoid use after free on rmap->obj array entries When calling irq_set_affinity_notifier() with NULL at the notify argument, it will cause freeing of the glue pointer in the corresponding array entry but will leave the pointer in the array. A subsequent call to free_irq_cpu_rmap() will try to free this entry again leading to possible use after free. Fix that by setting NULL to the array entry and checking that we have non-zero at the array entry when iterating over the array in free_irq_cpu_rmap(). The current code does not suffer from this since there are no cases where irq_set_affinity_notifier(irq, NULL) (note the NULL passed for the notify arg) is called, followed by a call to free_irq_cpu_rmap() so we don't hit and issue. Subsequent patches in this series excersize this flow, hence the required fix.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: do not ignore genmask when looking up chain by id When adding a rule to a chain referring to its ID, if that chain had been deleted on the same batch, the rule might end up referring to a deleted chain. This will lead to a WARNING like following: [ 33.098431] ------------[ cut here ]------------ [ 33.098678] WARNING: CPU: 5 PID: 69 at net/netfilter/nf_tables_api.c:2037 nf_tables_chain_destroy+0x23d/0x260 [ 33.099217] Modules linked in: [ 33.099388] CPU: 5 PID: 69 Comm: kworker/5:1 Not tainted 6.4.0+ #409 [ 33.099726] Workqueue: events nf_tables_trans_destroy_work [ 33.100018] RIP: 0010:nf_tables_chain_destroy+0x23d/0x260 [ 33.100306] Code: 8b 7c 24 68 e8 64 9c ed fe 4c 89 e7 e8 5c 9c ed fe 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 89 c6 89 c7 c3 cc cc cc cc <0f> 0b 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 89 c6 89 c7 [ 33.101271] RSP: 0018:ffffc900004ffc48 EFLAGS: 00010202 [ 33.101546] RAX: 0000000000000001 RBX: ffff888006fc0a28 RCX: 0000000000000000 [ 33.101920] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 [ 33.102649] RBP: ffffc900004ffc78 R08: 0000000000000000 R09: 0000000000000000 [ 33.103018] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8880135ef500 [ 33.103385] R13: 0000000000000000 R14: dead000000000122 R15: ffff888006fc0a10 [ 33.103762] FS: 0000000000000000(0000) GS:ffff888024c80000(0000) knlGS:0000000000000000 [ 33.104184] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 33.104493] CR2: 00007fe863b56a50 CR3: 00000000124b0001 CR4: 0000000000770ee0 [ 33.104872] PKRU: 55555554 [ 33.104999] Call Trace: [ 33.105113] <TASK> [ 33.105214] ? show_regs+0x72/0x90 [ 33.105371] ? __warn+0xa5/0x210 [ 33.105520] ? nf_tables_chain_destroy+0x23d/0x260 [ 33.105732] ? report_bug+0x1f2/0x200 [ 33.105902] ? handle_bug+0x46/0x90 [ 33.106546] ? exc_invalid_op+0x19/0x50 [ 33.106762] ? asm_exc_invalid_op+0x1b/0x20 [ 33.106995] ? nf_tables_chain_destroy+0x23d/0x260 [ 33.107249] ? nf_tables_chain_destroy+0x30/0x260 [ 33.107506] nf_tables_trans_destroy_work+0x669/0x680 [ 33.107782] ? mark_held_locks+0x28/0xa0 [ 33.107996] ? __pfx_nf_tables_trans_destroy_work+0x10/0x10 [ 33.108294] ? _raw_spin_unlock_irq+0x28/0x70 [ 33.108538] process_one_work+0x68c/0xb70 [ 33.108755] ? lock_acquire+0x17f/0x420 [ 33.108977] ? __pfx_process_one_work+0x10/0x10 [ 33.109218] ? do_raw_spin_lock+0x128/0x1d0 [ 33.109435] ? _raw_spin_lock_irq+0x71/0x80 [ 33.109634] worker_thread+0x2bd/0x700 [ 33.109817] ? __pfx_worker_thread+0x10/0x10 [ 33.110254] kthread+0x18b/0x1d0 [ 33.110410] ? __pfx_kthread+0x10/0x10 [ 33.110581] ret_from_fork+0x29/0x50 [ 33.110757] </TASK> [ 33.110866] irq event stamp: 1651 [ 33.111017] hardirqs last enabled at (1659): [<ffffffffa206a209>] __up_console_sem+0x79/0xa0 [ 33.111379] hardirqs last disabled at (1666): [<ffffffffa206a1ee>] __up_console_sem+0x5e/0xa0 [ 33.111740] softirqs last enabled at (1616): [<ffffffffa1f5d40e>] __irq_exit_rcu+0x9e/0xe0 [ 33.112094] softirqs last disabled at (1367): [<ffffffffa1f5d40e>] __irq_exit_rcu+0x9e/0xe0 [ 33.112453] ---[ end trace 0000000000000000 ]--- This is due to the nft_chain_lookup_byid ignoring the genmask. After this change, adding the new rule will fail as it will not find the chain.

In the Linux kernel, the following vulnerability has been resolved: accel/qaic: tighten bounds checking in decode_message() Copy the bounds checking from encode_message() to decode_message(). This patch addresses the following concerns. Ensure that there is enough space for at least one header so that we don't have a negative size later. if (msg_hdr_len < sizeof(*trans_hdr)) Ensure that we have enough space to read the next header from the msg->data. if (msg_len > msg_hdr_len - sizeof(*trans_hdr)) return -EINVAL; Check that the trans_hdr->len is not below the minimum size: if (hdr_len < sizeof(*trans_hdr)) This minimum check ensures that we don't corrupt memory in decode_passthrough() when we do. memcpy(out_trans->data, in_trans->data, len - sizeof(in_trans->hdr)); And finally, use size_add() to prevent an integer overflow: if (size_add(msg_len, hdr_len) > msg_hdr_len)

In the Linux kernel, the following vulnerability has been resolved: crypto: xts - Handle EBUSY correctly As it is xts only handles the special return value of EINPROGRESS, which means that in all other cases it will free data related to the request. However, as the caller of xts may specify MAY_BACKLOG, we also need to expect EBUSY and treat it in the same way. Otherwise backlogged requests will trigger a use-after-free.

In the Linux kernel, the following vulnerability has been resolved: xfrm: fix slab-use-after-free in decode_session6 When the xfrm device is set to the qdisc of the sfb type, the cb field of the sent skb may be modified during enqueuing. Then, slab-use-after-free may occur when the xfrm device sends IPv6 packets. The stack information is as follows: BUG: KASAN: slab-use-after-free in decode_session6+0x103f/0x1890 Read of size 1 at addr ffff8881111458ef by task swapper/3/0 CPU: 3 PID: 0 Comm: swapper/3 Not tainted 6.4.0-next-20230707 #409 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014 Call Trace: <IRQ> dump_stack_lvl+0xd9/0x150 print_address_description.constprop.0+0x2c/0x3c0 kasan_report+0x11d/0x130 decode_session6+0x103f/0x1890 __xfrm_decode_session+0x54/0xb0 xfrmi_xmit+0x173/0x1ca0 dev_hard_start_xmit+0x187/0x700 sch_direct_xmit+0x1a3/0xc30 __qdisc_run+0x510/0x17a0 __dev_queue_xmit+0x2215/0x3b10 neigh_connected_output+0x3c2/0x550 ip6_finish_output2+0x55a/0x1550 ip6_finish_output+0x6b9/0x1270 ip6_output+0x1f1/0x540 ndisc_send_skb+0xa63/0x1890 ndisc_send_rs+0x132/0x6f0 addrconf_rs_timer+0x3f1/0x870 call_timer_fn+0x1a0/0x580 expire_timers+0x29b/0x4b0 run_timer_softirq+0x326/0x910 __do_softirq+0x1d4/0x905 irq_exit_rcu+0xb7/0x120 sysvec_apic_timer_interrupt+0x97/0xc0 </IRQ> <TASK> asm_sysvec_apic_timer_interrupt+0x1a/0x20 RIP: 0010:intel_idle_hlt+0x23/0x30 Code: 1f 84 00 00 00 00 00 f3 0f 1e fa 41 54 41 89 d4 0f 1f 44 00 00 66 90 0f 1f 44 00 00 0f 00 2d c4 9f ab 00 0f 1f 44 00 00 fb f4 <fa> 44 89 e0 41 5c c3 66 0f 1f 44 00 00 f3 0f 1e fa 41 54 41 89 d4 RSP: 0018:ffffc90000197d78 EFLAGS: 00000246 RAX: 00000000000a83c3 RBX: ffffe8ffffd09c50 RCX: ffffffff8a22d8e5 RDX: 0000000000000001 RSI: ffffffff8d3f8080 RDI: ffffe8ffffd09c50 RBP: ffffffff8d3f8080 R08: 0000000000000001 R09: ffffed1026ba6d9d R10: ffff888135d36ceb R11: 0000000000000001 R12: 0000000000000001 R13: ffffffff8d3f8100 R14: 0000000000000001 R15: 0000000000000000 cpuidle_enter_state+0xd3/0x6f0 cpuidle_enter+0x4e/0xa0 do_idle+0x2fe/0x3c0 cpu_startup_entry+0x18/0x20 start_secondary+0x200/0x290 secondary_startup_64_no_verify+0x167/0x16b </TASK> Allocated by task 939: kasan_save_stack+0x22/0x40 kasan_set_track+0x25/0x30 __kasan_slab_alloc+0x7f/0x90 kmem_cache_alloc_node+0x1cd/0x410 kmalloc_reserve+0x165/0x270 __alloc_skb+0x129/0x330 inet6_ifa_notify+0x118/0x230 __ipv6_ifa_notify+0x177/0xbe0 addrconf_dad_completed+0x133/0xe00 addrconf_dad_work+0x764/0x1390 process_one_work+0xa32/0x16f0 worker_thread+0x67d/0x10c0 kthread+0x344/0x440 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff888111145800 which belongs to the cache skbuff_small_head of size 640 The buggy address is located 239 bytes inside of freed 640-byte region [ffff888111145800, ffff888111145a80) As commit f855691975bb ("xfrm6: Fix the nexthdr offset in _decode_session6.") showed, xfrm_decode_session was originally intended only for the receive path. IP6CB(skb)->nhoff is not set during transmission. Therefore, set the cb field in the skb to 0 before sending packets.

In the Linux kernel, the following vulnerability has been resolved: RDMA/bnxt_re: Properly order ib_device_unalloc() to avoid UAF ib_dealloc_device() should be called only after device cleanup. Fix the dealloc sequence.

In the Linux kernel, the following vulnerability has been resolved: udf: Do not bother merging very long extents When merging very long extents we try to push as much length as possible to the first extent. However this is unnecessarily complicated and not really worth the trouble. Furthermore there was a bug in the logic resulting in corrupting extents in the file as syzbot reproducer shows. So just don't bother with the merging of extents that are too long together.

In the Linux kernel, the following vulnerability has been resolved: virtio-mmio: don't break lifecycle of vm_dev vm_dev has a separate lifecycle because it has a 'struct device' embedded. Thus, having a release callback for it is correct. Allocating the vm_dev struct with devres totally breaks this protection, though. Instead of waiting for the vm_dev release callback, the memory is freed when the platform_device is removed. Resulting in a use-after-free when finally the callback is to be called. To easily see the problem, compile the kernel with CONFIG_DEBUG_KOBJECT_RELEASE and unbind with sysfs. The fix is easy, don't use devres in this case. Found during my research about object lifetime problems.

In the Linux kernel, the following vulnerability has been resolved: macvlan: add forgotten nla_policy for IFLA_MACVLAN_BC_CUTOFF The previous commit 954d1fa1ac93 ("macvlan: Add netlink attribute for broadcast cutoff") added one additional attribute named IFLA_MACVLAN_BC_CUTOFF to allow broadcast cutfoff. However, it forgot to describe the nla_policy at macvlan_policy (drivers/net/macvlan.c). Hence, this suppose NLA_S32 (4 bytes) integer can be faked as empty (0 bytes) by a malicious user, which could leads to OOB in heap just like CVE-2023-3773. To fix it, this commit just completes the nla_policy description for IFLA_MACVLAN_BC_CUTOFF. This enforces the length check and avoids the potential OOB read.

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: pcie: Fix integer overflow in iwl_write_to_user_buf An integer overflow occurs in the iwl_write_to_user_buf() function, which is called by the iwl_dbgfs_monitor_data_read() function. static bool iwl_write_to_user_buf(char __user *user_buf, ssize_t count, void *buf, ssize_t *size, ssize_t *bytes_copied) { int buf_size_left = count - *bytes_copied; buf_size_left = buf_size_left - (buf_size_left % sizeof(u32)); if (*size > buf_size_left) *size = buf_size_left; If the user passes a SIZE_MAX value to the "ssize_t count" parameter, the ssize_t count parameter is assigned to "int buf_size_left". Then compare "*size" with "buf_size_left" . Here, "buf_size_left" is a negative number, so "*size" is assigned "buf_size_left" and goes into the third argument of the copy_to_user function, causing a heap overflow. This is not a security vulnerability because iwl_dbgfs_monitor_data_read() is a debugfs operation with 0400 privileges.

In the Linux kernel, the following vulnerability has been resolved: blk-crypto: make blk_crypto_evict_key() more robust If blk_crypto_evict_key() sees that the key is still in-use (due to a bug) or that ->keyslot_evict failed, it currently just returns while leaving the key linked into the keyslot management structures. However, blk_crypto_evict_key() is only called in contexts such as inode eviction where failure is not an option. So actually the caller proceeds with freeing the blk_crypto_key regardless of the return value of blk_crypto_evict_key(). These two assumptions don't match, and the result is that there can be a use-after-free in blk_crypto_reprogram_all_keys() after one of these errors occurs. (Note, these errors *shouldn't* happen; we're just talking about what happens if they do anyway.) Fix this by making blk_crypto_evict_key() unlink the key from the keyslot management structures even on failure. Also improve some comments.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid use-after-free for cached IPU bio xfstest generic/019 reports a bug: kernel BUG at mm/filemap.c:1619! RIP: 0010:folio_end_writeback+0x8a/0x90 Call Trace: end_page_writeback+0x1c/0x60 f2fs_write_end_io+0x199/0x420 bio_endio+0x104/0x180 submit_bio_noacct+0xa5/0x510 submit_bio+0x48/0x80 f2fs_submit_write_bio+0x35/0x300 f2fs_submit_merged_ipu_write+0x2a0/0x2b0 f2fs_write_single_data_page+0x838/0x8b0 f2fs_write_cache_pages+0x379/0xa30 f2fs_write_data_pages+0x30c/0x340 do_writepages+0xd8/0x1b0 __writeback_single_inode+0x44/0x370 writeback_sb_inodes+0x233/0x4d0 __writeback_inodes_wb+0x56/0xf0 wb_writeback+0x1dd/0x2d0 wb_workfn+0x367/0x4a0 process_one_work+0x21d/0x430 worker_thread+0x4e/0x3c0 kthread+0x103/0x130 ret_from_fork+0x2c/0x50 The root cause is: after cp_error is set, f2fs_submit_merged_ipu_write() in f2fs_write_single_data_page() tries to flush IPU bio in cache, however f2fs_submit_merged_ipu_write() missed to check validity of @bio parameter, result in submitting random cached bio which belong to other IO context, then it will cause use-after-free issue, fix it by adding additional validity check.

In the Linux kernel, the following vulnerability has been resolved: staging: ks7010: potential buffer overflow in ks_wlan_set_encode_ext() The "exc->key_len" is a u16 that comes from the user. If it's over IW_ENCODING_TOKEN_MAX (64) that could lead to memory corruption.

In the Linux kernel, the following vulnerability has been resolved: ext2: Check block size validity during mount Check that log of block size stored in the superblock has sensible value. Otherwise the shift computing the block size can overflow leading to undefined behavior.

In the Linux kernel, the following vulnerability has been resolved: ring-buffer: Sync IRQ works before buffer destruction If something was written to the buffer just before destruction, it may be possible (maybe not in a real system, but it did happen in ARCH=um with time-travel) to destroy the ringbuffer before the IRQ work ran, leading this KASAN report (or a crash without KASAN): BUG: KASAN: slab-use-after-free in irq_work_run_list+0x11a/0x13a Read of size 8 at addr 000000006d640a48 by task swapper/0 CPU: 0 PID: 0 Comm: swapper Tainted: G W O 6.3.0-rc1 #7 Stack: 60c4f20f 0c203d48 41b58ab3 60f224fc 600477fa 60f35687 60c4f20f 601273dd 00000008 6101eb00 6101eab0 615be548 Call Trace: [<60047a58>] show_stack+0x25e/0x282 [<60c609e0>] dump_stack_lvl+0x96/0xfd [<60c50d4c>] print_report+0x1a7/0x5a8 [<603078d3>] kasan_report+0xc1/0xe9 [<60308950>] __asan_report_load8_noabort+0x1b/0x1d [<60232844>] irq_work_run_list+0x11a/0x13a [<602328b4>] irq_work_tick+0x24/0x34 [<6017f9dc>] update_process_times+0x162/0x196 [<6019f335>] tick_sched_handle+0x1a4/0x1c3 [<6019fd9e>] tick_sched_timer+0x79/0x10c [<601812b9>] __hrtimer_run_queues.constprop.0+0x425/0x695 [<60182913>] hrtimer_interrupt+0x16c/0x2c4 [<600486a3>] um_timer+0x164/0x183 [...] Allocated by task 411: save_stack_trace+0x99/0xb5 stack_trace_save+0x81/0x9b kasan_save_stack+0x2d/0x54 kasan_set_track+0x34/0x3e kasan_save_alloc_info+0x25/0x28 ____kasan_kmalloc+0x8b/0x97 __kasan_kmalloc+0x10/0x12 __kmalloc+0xb2/0xe8 load_elf_phdrs+0xee/0x182 [...] The buggy address belongs to the object at 000000006d640800 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 584 bytes inside of freed 1024-byte region [000000006d640800, 000000006d640c00) Add the appropriate irq_work_sync() so the work finishes before the buffers are destroyed. Prior to the commit in the Fixes tag below, there was only a single global IRQ work, so this issue didn't exist.

In the Linux kernel, the following vulnerability has been resolved: drivers: base: Free devm resources when unregistering a device In the current code, devres_release_all() only gets called if the device has a bus and has been probed. This leads to issues when using bus-less or driver-less devices where the device might never get freed if a managed resource holds a reference to the device. This is happening in the DRM framework for example. We should thus call devres_release_all() in the device_del() function to make sure that the device-managed actions are properly executed when the device is unregistered, even if it has neither a bus nor a driver. This is effectively the same change than commit 2f8d16a996da ("devres: release resources on device_del()") that got reverted by commit a525a3ddeaca ("driver core: free devres in device_release") over memory leaks concerns. This patch effectively combines the two commits mentioned above to release the resources both on device_del() and device_release() and get the best of both worlds.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix possible double unlock when moving a directory

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: Fix a memory corruption issue A few lines above, space is kzalloc()'ed for: sizeof(struct iwl_nvm_data) + sizeof(struct ieee80211_channel) + sizeof(struct ieee80211_rate) 'mvm->nvm_data' is a 'struct iwl_nvm_data', so it is fine. At the end of this structure, there is the 'channels' flex array. Each element is of type 'struct ieee80211_channel'. So only 1 element is allocated in this array. When doing: mvm->nvm_data->bands[0].channels = mvm->nvm_data->channels; We point at the first element of the 'channels' flex array. So this is fine. However, when doing: mvm->nvm_data->bands[0].bitrates = (void *)((u8 *)mvm->nvm_data->channels + 1); because of the "(u8 *)" cast, we add only 1 to the address of the beginning of the flex array. It is likely that we want point at the 'struct ieee80211_rate' allocated just after. Remove the spurious casting so that the pointer arithmetic works as expected.

In the Linux kernel, the following vulnerability has been resolved: f2fs: explicitly null-terminate the xattr list When setting an xattr, explicitly null-terminate the xattr list. This eliminates the fragile assumption that the unused xattr space is always zeroed.

In the Linux kernel, the following vulnerability has been resolved: crypto: scomp - fix req->dst buffer overflow The req->dst buffer size should be checked before copying from the scomp_scratch->dst to avoid req->dst buffer overflow problem.

In the Linux kernel, the following vulnerability has been resolved: mctp: perform route lookups under a RCU read-side lock Our current route lookups (mctp_route_lookup and mctp_route_lookup_null) traverse the net's route list without the RCU read lock held. This means the route lookup is subject to preemption, resulting in an potential grace period expiry, and so an eventual kfree() while we still have the route pointer. Add the proper read-side critical section locks around the route lookups, preventing premption and a possible parallel kfree. The remaining net->mctp.routes accesses are already under a rcu_read_lock, or protected by the RTNL for updates. Based on an analysis from Sili Luo <rootlab@huawei.com>, where introducing a delay in the route lookup could cause a UAF on simultaneous sendmsg() and route deletion.

In the Linux kernel, the following vulnerability has been resolved: crypto: s390/aes - Fix buffer overread in CTR mode When processing the last block, the s390 ctr code will always read a whole block, even if there isn't a whole block of data left. Fix this by using the actual length left and copy it into a buffer first for processing.

In the Linux kernel, the following vulnerability has been resolved: can: j1939: Fix UAF in j1939_sk_match_filter during setsockopt(SO_J1939_FILTER) Lock jsk->sk to prevent UAF when setsockopt(..., SO_J1939_FILTER, ...) modifies jsk->filters while receiving packets. Following trace was seen on affected system: ================================================================== BUG: KASAN: slab-use-after-free in j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939] Read of size 4 at addr ffff888012144014 by task j1939/350 CPU: 0 PID: 350 Comm: j1939 Tainted: G W OE 6.5.0-rc5 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 Call Trace: print_report+0xd3/0x620 ? kasan_complete_mode_report_info+0x7d/0x200 ? j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939] kasan_report+0xc2/0x100 ? j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939] __asan_load4+0x84/0xb0 j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939] j1939_sk_recv+0x20b/0x320 [can_j1939] ? __kasan_check_write+0x18/0x20 ? __pfx_j1939_sk_recv+0x10/0x10 [can_j1939] ? j1939_simple_recv+0x69/0x280 [can_j1939] ? j1939_ac_recv+0x5e/0x310 [can_j1939] j1939_can_recv+0x43f/0x580 [can_j1939] ? __pfx_j1939_can_recv+0x10/0x10 [can_j1939] ? raw_rcv+0x42/0x3c0 [can_raw] ? __pfx_j1939_can_recv+0x10/0x10 [can_j1939] can_rcv_filter+0x11f/0x350 [can] can_receive+0x12f/0x190 [can] ? __pfx_can_rcv+0x10/0x10 [can] can_rcv+0xdd/0x130 [can] ? __pfx_can_rcv+0x10/0x10 [can] __netif_receive_skb_one_core+0x13d/0x150 ? __pfx___netif_receive_skb_one_core+0x10/0x10 ? __kasan_check_write+0x18/0x20 ? _raw_spin_lock_irq+0x8c/0xe0 __netif_receive_skb+0x23/0xb0 process_backlog+0x107/0x260 __napi_poll+0x69/0x310 net_rx_action+0x2a1/0x580 ? __pfx_net_rx_action+0x10/0x10 ? __pfx__raw_spin_lock+0x10/0x10 ? handle_irq_event+0x7d/0xa0 __do_softirq+0xf3/0x3f8 do_softirq+0x53/0x80 </IRQ> <TASK> __local_bh_enable_ip+0x6e/0x70 netif_rx+0x16b/0x180 can_send+0x32b/0x520 [can] ? __pfx_can_send+0x10/0x10 [can] ? __check_object_size+0x299/0x410 raw_sendmsg+0x572/0x6d0 [can_raw] ? __pfx_raw_sendmsg+0x10/0x10 [can_raw] ? apparmor_socket_sendmsg+0x2f/0x40 ? __pfx_raw_sendmsg+0x10/0x10 [can_raw] sock_sendmsg+0xef/0x100 sock_write_iter+0x162/0x220 ? __pfx_sock_write_iter+0x10/0x10 ? __rtnl_unlock+0x47/0x80 ? security_file_permission+0x54/0x320 vfs_write+0x6ba/0x750 ? __pfx_vfs_write+0x10/0x10 ? __fget_light+0x1ca/0x1f0 ? __rcu_read_unlock+0x5b/0x280 ksys_write+0x143/0x170 ? __pfx_ksys_write+0x10/0x10 ? __kasan_check_read+0x15/0x20 ? fpregs_assert_state_consistent+0x62/0x70 __x64_sys_write+0x47/0x60 do_syscall_64+0x60/0x90 ? do_syscall_64+0x6d/0x90 ? irqentry_exit+0x3f/0x50 ? exc_page_fault+0x79/0xf0 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Allocated by task 348: kasan_save_stack+0x2a/0x50 kasan_set_track+0x29/0x40 kasan_save_alloc_info+0x1f/0x30 __kasan_kmalloc+0xb5/0xc0 __kmalloc_node_track_caller+0x67/0x160 j1939_sk_setsockopt+0x284/0x450 [can_j1939] __sys_setsockopt+0x15c/0x2f0 __x64_sys_setsockopt+0x6b/0x80 do_syscall_64+0x60/0x90 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Freed by task 349: kasan_save_stack+0x2a/0x50 kasan_set_track+0x29/0x40 kasan_save_free_info+0x2f/0x50 __kasan_slab_free+0x12e/0x1c0 __kmem_cache_free+0x1b9/0x380 kfree+0x7a/0x120 j1939_sk_setsockopt+0x3b2/0x450 [can_j1939] __sys_setsockopt+0x15c/0x2f0 __x64_sys_setsockopt+0x6b/0x80 do_syscall_64+0x60/0x90 entry_SYSCALL_64_after_hwframe+0x6e/0xd8

In the Linux kernel, the following vulnerability has been resolved: wifi: ath9k: Fix potential array-index-out-of-bounds read in ath9k_htc_txstatus() Fix an array-index-out-of-bounds read in ath9k_htc_txstatus(). The bug occurs when txs->cnt, data from a URB provided by a USB device, is bigger than the size of the array txs->txstatus, which is HTC_MAX_TX_STATUS. WARN_ON() already checks it, but there is no bug handling code after the check. Make the function return if that is the case. Found by a modified version of syzkaller. UBSAN: array-index-out-of-bounds in htc_drv_txrx.c index 13 is out of range for type '__wmi_event_txstatus [12]' Call Trace: ath9k_htc_txstatus ath9k_wmi_event_tasklet tasklet_action_common __do_softirq irq_exit_rxu sysvec_apic_timer_interrupt

In the Linux kernel, the following vulnerability has been resolved: cifs: Fix UAF in cifs_demultiplex_thread() There is a UAF when xfstests on cifs: BUG: KASAN: use-after-free in smb2_is_network_name_deleted+0x27/0x160 Read of size 4 at addr ffff88810103fc08 by task cifsd/923 CPU: 1 PID: 923 Comm: cifsd Not tainted 6.1.0-rc4+ #45 ... Call Trace: <TASK> dump_stack_lvl+0x34/0x44 print_report+0x171/0x472 kasan_report+0xad/0x130 kasan_check_range+0x145/0x1a0 smb2_is_network_name_deleted+0x27/0x160 cifs_demultiplex_thread.cold+0x172/0x5a4 kthread+0x165/0x1a0 ret_from_fork+0x1f/0x30 </TASK> Allocated by task 923: kasan_save_stack+0x1e/0x40 kasan_set_track+0x21/0x30 __kasan_slab_alloc+0x54/0x60 kmem_cache_alloc+0x147/0x320 mempool_alloc+0xe1/0x260 cifs_small_buf_get+0x24/0x60 allocate_buffers+0xa1/0x1c0 cifs_demultiplex_thread+0x199/0x10d0 kthread+0x165/0x1a0 ret_from_fork+0x1f/0x30 Freed by task 921: kasan_save_stack+0x1e/0x40 kasan_set_track+0x21/0x30 kasan_save_free_info+0x2a/0x40 ____kasan_slab_free+0x143/0x1b0 kmem_cache_free+0xe3/0x4d0 cifs_small_buf_release+0x29/0x90 SMB2_negotiate+0x8b7/0x1c60 smb2_negotiate+0x51/0x70 cifs_negotiate_protocol+0xf0/0x160 cifs_get_smb_ses+0x5fa/0x13c0 mount_get_conns+0x7a/0x750 cifs_mount+0x103/0xd00 cifs_smb3_do_mount+0x1dd/0xcb0 smb3_get_tree+0x1d5/0x300 vfs_get_tree+0x41/0xf0 path_mount+0x9b3/0xdd0 __x64_sys_mount+0x190/0x1d0 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x46/0xb0 The UAF is because: mount(pid: 921) | cifsd(pid: 923) -------------------------------|------------------------------- | cifs_demultiplex_thread SMB2_negotiate | cifs_send_recv | compound_send_recv | smb_send_rqst | wait_for_response | wait_event_state [1] | | standard_receive3 | cifs_handle_standard | handle_mid | mid->resp_buf = buf; [2] | dequeue_mid [3] KILL the process [4] | resp_iov[i].iov_base = buf | free_rsp_buf [5] | | is_network_name_deleted [6] | callback 1. After send request to server, wait the response until mid->mid_state != SUBMITTED; 2. Receive response from server, and set it to mid; 3. Set the mid state to RECEIVED; 4. Kill the process, the mid state already RECEIVED, get 0; 5. Handle and release the negotiate response; 6. UAF. It can be easily reproduce with add some delay in [3] - [6]. Only sync call has the problem since async call's callback is executed in cifsd process. Add an extra state to mark the mid state to READY before wakeup the waitter, then it can get the resp safely.

In the Linux kernel, the following vulnerability has been resolved: Input: powermate - fix use-after-free in powermate_config_complete syzbot has found a use-after-free bug [1] in the powermate driver. This happens when the device is disconnected, which leads to a memory free from the powermate_device struct. When an asynchronous control message completes after the kfree and its callback is invoked, the lock does not exist anymore and hence the bug. Use usb_kill_urb() on pm->config to cancel any in-progress requests upon device disconnection. [1] https://syzkaller.appspot.com/bug?extid=0434ac83f907a1dbdd1e

In the Linux kernel, the following vulnerability has been resolved: iommu: Don't reserve 0-length IOVA region When the bootloader/firmware doesn't setup the framebuffers, their address and size are 0 in "iommu-addresses" property. If IOVA region is reserved with 0 length, then it ends up corrupting the IOVA rbtree with an entry which has pfn_hi < pfn_lo. If we intend to use display driver in kernel without framebuffer then it's causing the display IOMMU mappings to fail as entire valid IOVA space is reserved when address and length are passed as 0. An ideal solution would be firmware removing the "iommu-addresses" property and corresponding "memory-region" if display is not present. But the kernel should be able to handle this by checking for size of IOVA region and skipping the IOVA reservation if size is 0. Also, add a warning if firmware is requesting 0-length IOVA region reservation.

In the Linux kernel, the following vulnerability has been resolved: jfs: fix array-index-out-of-bounds in dbAdjTree Currently there is a bound check missing in the dbAdjTree while accessing the dmt_stree. To add the required check added the bool is_ctl which is required to determine the size as suggest in the following commit. https://lore.kernel.org/linux-kernel-mentees/f9475918-2186-49b8-b801-6f0f9e75f4fa@oracle.com/

In the Linux kernel, the following vulnerability has been resolved: powerpc/pseries/memhp: Fix access beyond end of drmem array dlpar_memory_remove_by_index() may access beyond the bounds of the drmem lmb array when the LMB lookup fails to match an entry with the given DRC index. When the search fails, the cursor is left pointing to &drmem_info->lmbs[drmem_info->n_lmbs], which is one element past the last valid entry in the array. The debug message at the end of the function then dereferences this pointer: pr_debug("Failed to hot-remove memory at %llx\n", lmb->base_addr); This was found by inspection and confirmed with KASAN: pseries-hotplug-mem: Attempting to hot-remove LMB, drc index 1234 ================================================================== BUG: KASAN: slab-out-of-bounds in dlpar_memory+0x298/0x1658 Read of size 8 at addr c000000364e97fd0 by task bash/949 dump_stack_lvl+0xa4/0xfc (unreliable) print_report+0x214/0x63c kasan_report+0x140/0x2e0 __asan_load8+0xa8/0xe0 dlpar_memory+0x298/0x1658 handle_dlpar_errorlog+0x130/0x1d0 dlpar_store+0x18c/0x3e0 kobj_attr_store+0x68/0xa0 sysfs_kf_write+0xc4/0x110 kernfs_fop_write_iter+0x26c/0x390 vfs_write+0x2d4/0x4e0 ksys_write+0xac/0x1a0 system_call_exception+0x268/0x530 system_call_vectored_common+0x15c/0x2ec Allocated by task 1: kasan_save_stack+0x48/0x80 kasan_set_track+0x34/0x50 kasan_save_alloc_info+0x34/0x50 __kasan_kmalloc+0xd0/0x120 __kmalloc+0x8c/0x320 kmalloc_array.constprop.0+0x48/0x5c drmem_init+0x2a0/0x41c do_one_initcall+0xe0/0x5c0 kernel_init_freeable+0x4ec/0x5a0 kernel_init+0x30/0x1e0 ret_from_kernel_user_thread+0x14/0x1c The buggy address belongs to the object at c000000364e80000 which belongs to the cache kmalloc-128k of size 131072 The buggy address is located 0 bytes to the right of allocated 98256-byte region [c000000364e80000, c000000364e97fd0) ================================================================== pseries-hotplug-mem: Failed to hot-remove memory at 0 Log failed lookups with a separate message and dereference the cursor only when it points to a valid entry.

In the Linux kernel, the following vulnerability has been resolved: serial: 8250: omap: Don't skip resource freeing if pm_runtime_resume_and_get() failed Returning an error code from .remove() makes the driver core emit the little helpful error message: remove callback returned a non-zero value. This will be ignored. and then remove the device anyhow. So all resources that were not freed are leaked in this case. Skipping serial8250_unregister_port() has the potential to keep enough of the UART around to trigger a use-after-free. So replace the error return (and with it the little helpful error message) by a more useful error message and continue to cleanup.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix accesses to uninit stack slots Privileged programs are supposed to be able to read uninitialized stack memory (ever since 6715df8d5) but, before this patch, these accesses were permitted inconsistently. In particular, accesses were permitted above state->allocated_stack, but not below it. In other words, if the stack was already "large enough", the access was permitted, but otherwise the access was rejected instead of being allowed to "grow the stack". This undesired rejection was happening in two places: - in check_stack_slot_within_bounds() - in check_stack_range_initialized() This patch arranges for these accesses to be permitted. A bunch of tests that were relying on the old rejection had to change; all of them were changed to add also run unprivileged, in which case the old behavior persists. One tests couldn't be updated - global_func16 - because it can't run unprivileged for other reasons. This patch also fixes the tracking of the stack size for variable-offset reads. This second fix is bundled in the same commit as the first one because they're inter-related. Before this patch, writes to the stack using registers containing a variable offset (as opposed to registers with fixed, known values) were not properly contributing to the function's needed stack size. As a result, it was possible for a program to verify, but then to attempt to read out-of-bounds data at runtime because a too small stack had been allocated for it. Each function tracks the size of the stack it needs in bpf_subprog_info.stack_depth, which is maintained by update_stack_depth(). For regular memory accesses, check_mem_access() was calling update_state_depth() but it was passing in only the fixed part of the offset register, ignoring the variable offset. This was incorrect; the minimum possible value of that register should be used instead. This tracking is now fixed by centralizing the tracking of stack size in grow_stack_state(), and by lifting the calls to grow_stack_state() to check_stack_access_within_bounds() as suggested by Andrii. The code is now simpler and more convincingly tracks the correct maximum stack size. check_stack_range_initialized() can now rely on enough stack having been allocated for the access; this helps with the fix for the first issue. A few tests were changed to also check the stack depth computation. The one that fails without this patch is verifier_var_off:stack_write_priv_vs_unpriv.

A use-after-free vulnerability in the Linux kernel's netfilter: nf_tables component can be exploited to achieve local privilege escalation. Addition and removal of rules from chain bindings within the same transaction causes leads to use-after-free. We recommend upgrading past commit f15f29fd4779be8a418b66e9d52979bb6d6c2325.

In the Linux kernel, the following vulnerability has been resolved: jfs: fix uaf in jfs_evict_inode When the execution of diMount(ipimap) fails, the object ipimap that has been released may be accessed in diFreeSpecial(). Asynchronous ipimap release occurs when rcu_core() calls jfs_free_node(). Therefore, when diMount(ipimap) fails, sbi->ipimap should not be initialized as ipimap.

In the Linux kernel, the following vulnerability has been resolved: media: rc: bpf attach/detach requires write permission Note that bpf attach/detach also requires CAP_NET_ADMIN.

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Fix potential stack-out-of-bounds in brcmf_c_preinit_dcmds() This patch fixes a stack-out-of-bounds read in brcmfmac that occurs when 'buf' that is not null-terminated is passed as an argument of strsep() in brcmf_c_preinit_dcmds(). This buffer is filled with a firmware version string by memcpy() in brcmf_fil_iovar_data_get(). The patch ensures buf is null-terminated. Found by a modified version of syzkaller. [ 47.569679][ T1897] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43236b for chip BCM43236/3 [ 47.582839][ T1897] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available [ 47.601565][ T1897] ================================================================== [ 47.602574][ T1897] BUG: KASAN: stack-out-of-bounds in strsep+0x1b2/0x1f0 [ 47.603447][ T1897] Read of size 1 at addr ffffc90001f6f000 by task kworker/0:2/1897 [ 47.604336][ T1897] [ 47.604621][ T1897] CPU: 0 PID: 1897 Comm: kworker/0:2 Tainted: G O 5.14.0+ #131 [ 47.605617][ T1897] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 47.606907][ T1897] Workqueue: usb_hub_wq hub_event [ 47.607453][ T1897] Call Trace: [ 47.607801][ T1897] dump_stack_lvl+0x8e/0xd1 [ 47.608295][ T1897] print_address_description.constprop.0.cold+0xf/0x334 [ 47.609009][ T1897] ? strsep+0x1b2/0x1f0 [ 47.609434][ T1897] ? strsep+0x1b2/0x1f0 [ 47.609863][ T1897] kasan_report.cold+0x83/0xdf [ 47.610366][ T1897] ? strsep+0x1b2/0x1f0 [ 47.610882][ T1897] strsep+0x1b2/0x1f0 [ 47.611300][ T1897] ? brcmf_fil_iovar_data_get+0x3a/0xf0 [ 47.611883][ T1897] brcmf_c_preinit_dcmds+0x995/0xc40 [ 47.612434][ T1897] ? brcmf_c_set_joinpref_default+0x100/0x100 [ 47.613078][ T1897] ? rcu_read_lock_sched_held+0xa1/0xd0 [ 47.613662][ T1897] ? rcu_read_lock_bh_held+0xb0/0xb0 [ 47.614208][ T1897] ? lock_acquire+0x19d/0x4e0 [ 47.614704][ T1897] ? find_held_lock+0x2d/0x110 [ 47.615236][ T1897] ? brcmf_usb_deq+0x1a7/0x260 [ 47.615741][ T1897] ? brcmf_usb_rx_fill_all+0x5a/0xf0 [ 47.616288][ T1897] brcmf_attach+0x246/0xd40 [ 47.616758][ T1897] ? wiphy_new_nm+0x1703/0x1dd0 [ 47.617280][ T1897] ? kmemdup+0x43/0x50 [ 47.617720][ T1897] brcmf_usb_probe+0x12de/0x1690 [ 47.618244][ T1897] ? brcmf_usbdev_qinit.constprop.0+0x470/0x470 [ 47.618901][ T1897] usb_probe_interface+0x2aa/0x760 [ 47.619429][ T1897] ? usb_probe_device+0x250/0x250 [ 47.619950][ T1897] really_probe+0x205/0xb70 [ 47.620435][ T1897] ? driver_allows_async_probing+0x130/0x130 [ 47.621048][ T1897] __driver_probe_device+0x311/0x4b0 [ 47.621595][ T1897] ? driver_allows_async_probing+0x130/0x130 [ 47.622209][ T1897] driver_probe_device+0x4e/0x150 [ 47.622739][ T1897] __device_attach_driver+0x1cc/0x2a0 [ 47.623287][ T1897] bus_for_each_drv+0x156/0x1d0 [ 47.623796][ T1897] ? bus_rescan_devices+0x30/0x30 [ 47.624309][ T1897] ? lockdep_hardirqs_on_prepare+0x273/0x3e0 [ 47.624907][ T1897] ? trace_hardirqs_on+0x46/0x160 [ 47.625437][ T1897] __device_attach+0x23f/0x3a0 [ 47.625924][ T1897] ? device_bind_driver+0xd0/0xd0 [ 47.626433][ T1897] ? kobject_uevent_env+0x287/0x14b0 [ 47.627057][ T1897] bus_probe_device+0x1da/0x290 [ 47.627557][ T1897] device_add+0xb7b/0x1eb0 [ 47.628027][ T1897] ? wait_for_completion+0x290/0x290 [ 47.628593][ T1897] ? __fw_devlink_link_to_suppliers+0x5a0/0x5a0 [ 47.629249][ T1897] usb_set_configuration+0xf59/0x16f0 [ 47.629829][ T1897] usb_generic_driver_probe+0x82/0xa0 [ 47.630385][ T1897] usb_probe_device+0xbb/0x250 [ 47.630927][ T1897] ? usb_suspend+0x590/0x590 [ 47.631397][ T1897] really_probe+0x205/0xb70 [ 47.631855][ T1897] ? driver_allows_async_probing+0x130/0x130 [ 47.632469][ T1897] __driver_probe_device+0x311/0x4b0 [ 47.633002][ ---truncated---

Linux kernel is vulnerable to a heap-based buffer overflow in the fs/ext4/xattr.c:ext4_xattr_set_entry() function. An attacker could exploit this by operating on a mounted crafted ext4 image.

In the Linux kernel, the following vulnerability has been resolved: udf: Fix a slab-out-of-bounds write bug in udf_find_entry() Syzbot reported a slab-out-of-bounds Write bug: loop0: detected capacity change from 0 to 2048 ================================================================== BUG: KASAN: slab-out-of-bounds in udf_find_entry+0x8a5/0x14f0 fs/udf/namei.c:253 Write of size 105 at addr ffff8880123ff896 by task syz-executor323/3610 CPU: 0 PID: 3610 Comm: syz-executor323 Not tainted 6.1.0-rc2-syzkaller-00105-gb229b6ca5abb #0 Hardware name: Google Compute Engine/Google Compute Engine, BIOS Google 10/11/2022 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x1b1/0x28e lib/dump_stack.c:106 print_address_description+0x74/0x340 mm/kasan/report.c:284 print_report+0x107/0x1f0 mm/kasan/report.c:395 kasan_report+0xcd/0x100 mm/kasan/report.c:495 kasan_check_range+0x2a7/0x2e0 mm/kasan/generic.c:189 memcpy+0x3c/0x60 mm/kasan/shadow.c:66 udf_find_entry+0x8a5/0x14f0 fs/udf/namei.c:253 udf_lookup+0xef/0x340 fs/udf/namei.c:309 lookup_open fs/namei.c:3391 [inline] open_last_lookups fs/namei.c:3481 [inline] path_openat+0x10e6/0x2df0 fs/namei.c:3710 do_filp_open+0x264/0x4f0 fs/namei.c:3740 do_sys_openat2+0x124/0x4e0 fs/open.c:1310 do_sys_open fs/open.c:1326 [inline] __do_sys_creat fs/open.c:1402 [inline] __se_sys_creat fs/open.c:1396 [inline] __x64_sys_creat+0x11f/0x160 fs/open.c:1396 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7ffab0d164d9 Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffe1a7e6bb8 EFLAGS: 00000246 ORIG_RAX: 0000000000000055 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007ffab0d164d9 RDX: 00007ffab0d164d9 RSI: 0000000000000000 RDI: 0000000020000180 RBP: 00007ffab0cd5a10 R08: 0000000000000000 R09: 0000000000000000 R10: 00005555573552c0 R11: 0000000000000246 R12: 00007ffab0cd5aa0 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 </TASK> Allocated by task 3610: kasan_save_stack mm/kasan/common.c:45 [inline] kasan_set_track+0x3d/0x60 mm/kasan/common.c:52 ____kasan_kmalloc mm/kasan/common.c:371 [inline] __kasan_kmalloc+0x97/0xb0 mm/kasan/common.c:380 kmalloc include/linux/slab.h:576 [inline] udf_find_entry+0x7b6/0x14f0 fs/udf/namei.c:243 udf_lookup+0xef/0x340 fs/udf/namei.c:309 lookup_open fs/namei.c:3391 [inline] open_last_lookups fs/namei.c:3481 [inline] path_openat+0x10e6/0x2df0 fs/namei.c:3710 do_filp_open+0x264/0x4f0 fs/namei.c:3740 do_sys_openat2+0x124/0x4e0 fs/open.c:1310 do_sys_open fs/open.c:1326 [inline] __do_sys_creat fs/open.c:1402 [inline] __se_sys_creat fs/open.c:1396 [inline] __x64_sys_creat+0x11f/0x160 fs/open.c:1396 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd The buggy address belongs to the object at ffff8880123ff800 which belongs to the cache kmalloc-256 of size 256 The buggy address is located 150 bytes inside of 256-byte region [ffff8880123ff800, ffff8880123ff900) The buggy address belongs to the physical page: page:ffffea000048ff80 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x123fe head:ffffea000048ff80 order:1 compound_mapcount:0 compound_pincount:0 flags: 0xfff00000010200(slab|head|node=0|zone=1|lastcpupid=0x7ff) raw: 00fff00000010200 ffffea00004b8500 dead000000000003 ffff888012041b40 raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected page_owner tracks the page as allocated page last allocated via order 0, migratetype Unmovable, gfp_mask 0x0(), pid 1, tgid 1 (swapper/0), ts 1841222404, free_ts 0 create_dummy_stack mm/page_owner.c: ---truncated---

Improper input validation in NI-PAL may allow a local authenticated user to access arbitrary system memory, potentially leading to privilege escalation. This vulnerability affects NI-PAL 26.3.0 and prior versions on Windows and Linux.