In the Linux kernel, the following vulnerability has been resolved: nvmet: avoid potential UAF in nvmet_req_complete() An nvme target ->queue_response() operation implementation may free the request passed as argument. Such implementation potentially could result in a use after free of the request pointer when percpu_ref_put() is called in nvmet_req_complete(). Avoid such problem by using a local variable to save the sq pointer before calling __nvmet_req_complete(), thus avoiding dereferencing the req pointer after that function call.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix htt mlo-offset event locking The ath12k active pdevs are protected by RCU but the htt mlo-offset event handling code calling ath12k_mac_get_ar_by_pdev_id() was not marked as a read-side critical section. Mark the code in question as an RCU read-side critical section to avoid any potential use-after-free issues. Compile tested only.

In the Linux kernel, the following vulnerability has been resolved: nbd: fix uaf in nbd_open Commit 4af5f2e03013 ("nbd: use blk_mq_alloc_disk and blk_cleanup_disk") cleans up disk by blk_cleanup_disk() and it won't set disk->private_data as NULL as before. UAF may be triggered in nbd_open() if someone tries to open nbd device right after nbd_put() since nbd has been free in nbd_dev_remove(). Fix this by implementing ->free_disk and free private data in it.

In the Linux kernel, the following vulnerability has been resolved: drivers/amd/pm: fix a use-after-free in kv_parse_power_table When ps allocated by kzalloc equals to NULL, kv_parse_power_table frees adev->pm.dpm.ps that allocated before. However, after the control flow goes through the following call chains: kv_parse_power_table |-> kv_dpm_init |-> kv_dpm_sw_init |-> kv_dpm_fini The adev->pm.dpm.ps is used in the for loop of kv_dpm_fini after its first free in kv_parse_power_table and causes a use-after-free bug.

A use-after-free vulnerability in the Linux kernel's netfilter: nf_tables component can be exploited to achieve local privilege escalation. Addition and removal of rules from chain bindings within the same transaction causes leads to use-after-free. We recommend upgrading past commit f15f29fd4779be8a418b66e9d52979bb6d6c2325.

In the Linux kernel, the following vulnerability has been resolved: media: mtk-jpeg: Fix use after free bug due to error path handling in mtk_jpeg_dec_device_run In mtk_jpeg_probe, &jpeg->job_timeout_work is bound with mtk_jpeg_job_timeout_work. In mtk_jpeg_dec_device_run, if error happens in mtk_jpeg_set_dec_dst, it will finally start the worker while mark the job as finished by invoking v4l2_m2m_job_finish. There are two methods to trigger the bug. If we remove the module, it which will call mtk_jpeg_remove to make cleanup. The possible sequence is as follows, which will cause a use-after-free bug. CPU0 CPU1 mtk_jpeg_dec_... | start worker | |mtk_jpeg_job_timeout_work mtk_jpeg_remove | v4l2_m2m_release | kfree(m2m_dev); | | | v4l2_m2m_get_curr_priv | m2m_dev->curr_ctx //use If we close the file descriptor, which will call mtk_jpeg_release, it will have a similar sequence. Fix this bug by starting timeout worker only if started jpegdec worker successfully. Then v4l2_m2m_job_finish will only be called in either mtk_jpeg_job_timeout_work or mtk_jpeg_dec_device_run.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix a race condition between btf_put() and map_free() When running `./test_progs -j` in my local vm with latest kernel, I once hit a kasan error like below: [ 1887.184724] BUG: KASAN: slab-use-after-free in bpf_rb_root_free+0x1f8/0x2b0 [ 1887.185599] Read of size 4 at addr ffff888106806910 by task kworker/u12:2/2830 [ 1887.186498] [ 1887.186712] CPU: 3 PID: 2830 Comm: kworker/u12:2 Tainted: G OEL 6.7.0-rc3-00699-g90679706d486-dirty #494 [ 1887.188034] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 1887.189618] Workqueue: events_unbound bpf_map_free_deferred [ 1887.190341] Call Trace: [ 1887.190666] <TASK> [ 1887.190949] dump_stack_lvl+0xac/0xe0 [ 1887.191423] ? nf_tcp_handle_invalid+0x1b0/0x1b0 [ 1887.192019] ? panic+0x3c0/0x3c0 [ 1887.192449] print_report+0x14f/0x720 [ 1887.192930] ? preempt_count_sub+0x1c/0xd0 [ 1887.193459] ? __virt_addr_valid+0xac/0x120 [ 1887.194004] ? bpf_rb_root_free+0x1f8/0x2b0 [ 1887.194572] kasan_report+0xc3/0x100 [ 1887.195085] ? bpf_rb_root_free+0x1f8/0x2b0 [ 1887.195668] bpf_rb_root_free+0x1f8/0x2b0 [ 1887.196183] ? __bpf_obj_drop_impl+0xb0/0xb0 [ 1887.196736] ? preempt_count_sub+0x1c/0xd0 [ 1887.197270] ? preempt_count_sub+0x1c/0xd0 [ 1887.197802] ? _raw_spin_unlock+0x1f/0x40 [ 1887.198319] bpf_obj_free_fields+0x1d4/0x260 [ 1887.198883] array_map_free+0x1a3/0x260 [ 1887.199380] bpf_map_free_deferred+0x7b/0xe0 [ 1887.199943] process_scheduled_works+0x3a2/0x6c0 [ 1887.200549] worker_thread+0x633/0x890 [ 1887.201047] ? __kthread_parkme+0xd7/0xf0 [ 1887.201574] ? kthread+0x102/0x1d0 [ 1887.202020] kthread+0x1ab/0x1d0 [ 1887.202447] ? pr_cont_work+0x270/0x270 [ 1887.202954] ? kthread_blkcg+0x50/0x50 [ 1887.203444] ret_from_fork+0x34/0x50 [ 1887.203914] ? kthread_blkcg+0x50/0x50 [ 1887.204397] ret_from_fork_asm+0x11/0x20 [ 1887.204913] </TASK> [ 1887.204913] </TASK> [ 1887.205209] [ 1887.205416] Allocated by task 2197: [ 1887.205881] kasan_set_track+0x3f/0x60 [ 1887.206366] __kasan_kmalloc+0x6e/0x80 [ 1887.206856] __kmalloc+0xac/0x1a0 [ 1887.207293] btf_parse_fields+0xa15/0x1480 [ 1887.207836] btf_parse_struct_metas+0x566/0x670 [ 1887.208387] btf_new_fd+0x294/0x4d0 [ 1887.208851] __sys_bpf+0x4ba/0x600 [ 1887.209292] __x64_sys_bpf+0x41/0x50 [ 1887.209762] do_syscall_64+0x4c/0xf0 [ 1887.210222] entry_SYSCALL_64_after_hwframe+0x63/0x6b [ 1887.210868] [ 1887.211074] Freed by task 36: [ 1887.211460] kasan_set_track+0x3f/0x60 [ 1887.211951] kasan_save_free_info+0x28/0x40 [ 1887.212485] ____kasan_slab_free+0x101/0x180 [ 1887.213027] __kmem_cache_free+0xe4/0x210 [ 1887.213514] btf_free+0x5b/0x130 [ 1887.213918] rcu_core+0x638/0xcc0 [ 1887.214347] __do_softirq+0x114/0x37e The error happens at bpf_rb_root_free+0x1f8/0x2b0: 00000000000034c0 <bpf_rb_root_free>: ; { 34c0: f3 0f 1e fa endbr64 34c4: e8 00 00 00 00 callq 0x34c9 <bpf_rb_root_free+0x9> 34c9: 55 pushq %rbp 34ca: 48 89 e5 movq %rsp, %rbp ... ; if (rec && rec->refcount_off >= 0 && 36aa: 4d 85 ed testq %r13, %r13 36ad: 74 a9 je 0x3658 <bpf_rb_root_free+0x198> 36af: 49 8d 7d 10 leaq 0x10(%r13), %rdi 36b3: e8 00 00 00 00 callq 0x36b8 <bpf_rb_root_free+0x1f8> <==== kasan function 36b8: 45 8b 7d 10 movl 0x10(%r13), %r15d <==== use-after-free load 36bc: 45 85 ff testl %r15d, %r15d 36bf: 78 8c js 0x364d <bpf_rb_root_free+0x18d> So the problem ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ieee802154: ca8210: Fix a potential UAF in ca8210_probe If of_clk_add_provider() fails in ca8210_register_ext_clock(), it calls clk_unregister() to release priv->clk and returns an error. However, the caller ca8210_probe() then calls ca8210_remove(), where priv->clk is freed again in ca8210_unregister_ext_clock(). In this case, a use-after-free may happen in the second time we call clk_unregister(). Fix this by removing the first clk_unregister(). Also, priv->clk could be an error code on failure of clk_register_fixed_rate(). Use IS_ERR_OR_NULL to catch this case in ca8210_unregister_ext_clock().

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt. ---truncated---

In the Linux kernel, the following vulnerability has been resolved: serial: 8250: omap: Don't skip resource freeing if pm_runtime_resume_and_get() failed Returning an error code from .remove() makes the driver core emit the little helpful error message: remove callback returned a non-zero value. This will be ignored. and then remove the device anyhow. So all resources that were not freed are leaked in this case. Skipping serial8250_unregister_port() has the potential to keep enough of the UART around to trigger a use-after-free. So replace the error return (and with it the little helpful error message) by a more useful error message and continue to cleanup.

In the Linux kernel, the following vulnerability has been resolved: cifs: Fix use-after-free in rdata->read_into_pages() When the network status is unstable, use-after-free may occur when read data from the server. BUG: KASAN: use-after-free in readpages_fill_pages+0x14c/0x7e0 Call Trace: <TASK> dump_stack_lvl+0x38/0x4c print_report+0x16f/0x4a6 kasan_report+0xb7/0x130 readpages_fill_pages+0x14c/0x7e0 cifs_readv_receive+0x46d/0xa40 cifs_demultiplex_thread+0x121c/0x1490 kthread+0x16b/0x1a0 ret_from_fork+0x2c/0x50 </TASK> Allocated by task 2535: kasan_save_stack+0x22/0x50 kasan_set_track+0x25/0x30 __kasan_kmalloc+0x82/0x90 cifs_readdata_direct_alloc+0x2c/0x110 cifs_readdata_alloc+0x2d/0x60 cifs_readahead+0x393/0xfe0 read_pages+0x12f/0x470 page_cache_ra_unbounded+0x1b1/0x240 filemap_get_pages+0x1c8/0x9a0 filemap_read+0x1c0/0x540 cifs_strict_readv+0x21b/0x240 vfs_read+0x395/0x4b0 ksys_read+0xb8/0x150 do_syscall_64+0x3f/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc Freed by task 79: kasan_save_stack+0x22/0x50 kasan_set_track+0x25/0x30 kasan_save_free_info+0x2e/0x50 __kasan_slab_free+0x10e/0x1a0 __kmem_cache_free+0x7a/0x1a0 cifs_readdata_release+0x49/0x60 process_one_work+0x46c/0x760 worker_thread+0x2a4/0x6f0 kthread+0x16b/0x1a0 ret_from_fork+0x2c/0x50 Last potentially related work creation: kasan_save_stack+0x22/0x50 __kasan_record_aux_stack+0x95/0xb0 insert_work+0x2b/0x130 __queue_work+0x1fe/0x660 queue_work_on+0x4b/0x60 smb2_readv_callback+0x396/0x800 cifs_abort_connection+0x474/0x6a0 cifs_reconnect+0x5cb/0xa50 cifs_readv_from_socket.cold+0x22/0x6c cifs_read_page_from_socket+0xc1/0x100 readpages_fill_pages.cold+0x2f/0x46 cifs_readv_receive+0x46d/0xa40 cifs_demultiplex_thread+0x121c/0x1490 kthread+0x16b/0x1a0 ret_from_fork+0x2c/0x50 The following function calls will cause UAF of the rdata pointer. readpages_fill_pages cifs_read_page_from_socket cifs_readv_from_socket cifs_reconnect __cifs_reconnect cifs_abort_connection mid->callback() --> smb2_readv_callback queue_work(&rdata->work) # if the worker completes first, # the rdata is freed cifs_readv_complete kref_put cifs_readdata_release kfree(rdata) return rdata->... # UAF in readpages_fill_pages() Similarly, this problem also occurs in the uncache_fill_pages(). Fix this by adjusts the order of condition judgment in the return statement.

In the Linux kernel, the following vulnerability has been resolved: vhost-vdpa: fix use after free in vhost_vdpa_probe() The put_device() calls vhost_vdpa_release_dev() which calls ida_simple_remove() and frees "v". So this call to ida_simple_remove() is a use after free and a double free.

In the Linux kernel, the following vulnerability has been resolved: ravb: Fix use-after-free issue in ravb_tx_timeout_work() The ravb_stop() should call cancel_work_sync(). Otherwise, ravb_tx_timeout_work() is possible to use the freed priv after ravb_remove() was called like below: CPU0 CPU1 ravb_tx_timeout() ravb_remove() unregister_netdev() free_netdev(ndev) // free priv ravb_tx_timeout_work() // use priv unregister_netdev() will call .ndo_stop() so that ravb_stop() is called. And, after phy_stop() is called, netif_carrier_off() is also called. So that .ndo_tx_timeout() will not be called after phy_stop().

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: fix potential key use-after-free When ieee80211_key_link() is called by ieee80211_gtk_rekey_add() but returns 0 due to KRACK protection (identical key reinstall), ieee80211_gtk_rekey_add() will still return a pointer into the key, in a potential use-after-free. This normally doesn't happen since it's only called by iwlwifi in case of WoWLAN rekey offload which has its own KRACK protection, but still better to fix, do that by returning an error code and converting that to success on the cfg80211 boundary only, leaving the error for bad callers of ieee80211_gtk_rekey_add().

In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: fix gtk offload status event locking The ath11k active pdevs are protected by RCU but the gtk offload status event handling code calling ath11k_mac_get_arvif_by_vdev_id() was not marked as a read-side critical section. Mark the code in question as an RCU read-side critical section to avoid any potential use-after-free issues. Compile tested only.

In the Linux kernel, the following vulnerability has been resolved: RDMA/srp: Do not call scsi_done() from srp_abort() After scmd_eh_abort_handler() has called the SCSI LLD eh_abort_handler callback, it performs one of the following actions: * Call scsi_queue_insert(). * Call scsi_finish_command(). * Call scsi_eh_scmd_add(). Hence, SCSI abort handlers must not call scsi_done(). Otherwise all the above actions would trigger a use-after-free. Hence remove the scsi_done() call from srp_abort(). Keep the srp_free_req() call before returning SUCCESS because we may not see the command again if SUCCESS is returned.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: L2CAP: Fix slab-use-after-free Read in l2cap_send_cmd After the hci sync command releases l2cap_conn, the hci receive data work queue references the released l2cap_conn when sending to the upper layer. Add hci dev lock to the hci receive data work queue to synchronize the two. [1] BUG: KASAN: slab-use-after-free in l2cap_send_cmd+0x187/0x8d0 net/bluetooth/l2cap_core.c:954 Read of size 8 at addr ffff8880271a4000 by task kworker/u9:2/5837 CPU: 0 UID: 0 PID: 5837 Comm: kworker/u9:2 Not tainted 6.13.0-rc5-syzkaller-00163-gab75170520d4 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 Workqueue: hci1 hci_rx_work Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0x169/0x550 mm/kasan/report.c:489 kasan_report+0x143/0x180 mm/kasan/report.c:602 l2cap_build_cmd net/bluetooth/l2cap_core.c:2964 [inline] l2cap_send_cmd+0x187/0x8d0 net/bluetooth/l2cap_core.c:954 l2cap_sig_send_rej net/bluetooth/l2cap_core.c:5502 [inline] l2cap_sig_channel net/bluetooth/l2cap_core.c:5538 [inline] l2cap_recv_frame+0x221f/0x10db0 net/bluetooth/l2cap_core.c:6817 hci_acldata_packet net/bluetooth/hci_core.c:3797 [inline] hci_rx_work+0x508/0xdb0 net/bluetooth/hci_core.c:4040 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0xa66/0x1840 kernel/workqueue.c:3310 worker_thread+0x870/0xd30 kernel/workqueue.c:3391 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 </TASK> Allocated by task 5837: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3f/0x80 mm/kasan/common.c:68 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0x98/0xb0 mm/kasan/common.c:394 kasan_kmalloc include/linux/kasan.h:260 [inline] __kmalloc_cache_noprof+0x243/0x390 mm/slub.c:4329 kmalloc_noprof include/linux/slab.h:901 [inline] kzalloc_noprof include/linux/slab.h:1037 [inline] l2cap_conn_add+0xa9/0x8e0 net/bluetooth/l2cap_core.c:6860 l2cap_connect_cfm+0x115/0x1090 net/bluetooth/l2cap_core.c:7239 hci_connect_cfm include/net/bluetooth/hci_core.h:2057 [inline] hci_remote_features_evt+0x68e/0xac0 net/bluetooth/hci_event.c:3726 hci_event_func net/bluetooth/hci_event.c:7473 [inline] hci_event_packet+0xac2/0x1540 net/bluetooth/hci_event.c:7525 hci_rx_work+0x3f3/0xdb0 net/bluetooth/hci_core.c:4035 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0xa66/0x1840 kernel/workqueue.c:3310 worker_thread+0x870/0xd30 kernel/workqueue.c:3391 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 Freed by task 54: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3f/0x80 mm/kasan/common.c:68 kasan_save_free_info+0x40/0x50 mm/kasan/generic.c:582 poison_slab_object mm/kasan/common.c:247 [inline] __kasan_slab_free+0x59/0x70 mm/kasan/common.c:264 kasan_slab_free include/linux/kasan.h:233 [inline] slab_free_hook mm/slub.c:2353 [inline] slab_free mm/slub.c:4613 [inline] kfree+0x196/0x430 mm/slub.c:4761 l2cap_connect_cfm+0xcc/0x1090 net/bluetooth/l2cap_core.c:7235 hci_connect_cfm include/net/bluetooth/hci_core.h:2057 [inline] hci_conn_failed+0x287/0x400 net/bluetooth/hci_conn.c:1266 hci_abort_conn_sync+0x56c/0x11f0 net/bluetooth/hci_sync.c:5603 hci_cmd_sync_work+0x22b/0x400 net/bluetooth/hci_sync.c:332 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0xa66/0x1840 kernel/workqueue.c:3310 worker_thread+0x870/0xd30 kernel/workqueue.c:3391 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entr ---truncated---

In the Linux kernel, the following vulnerability has been resolved: vhost-scsi: Fix handling of multiple calls to vhost_scsi_set_endpoint If vhost_scsi_set_endpoint is called multiple times without a vhost_scsi_clear_endpoint between them, we can hit multiple bugs found by Haoran Zhang: 1. Use-after-free when no tpgs are found: This fixes a use after free that occurs when vhost_scsi_set_endpoint is called more than once and calls after the first call do not find any tpgs to add to the vs_tpg. When vhost_scsi_set_endpoint first finds tpgs to add to the vs_tpg array match=true, so we will do: vhost_vq_set_backend(vq, vs_tpg); ... kfree(vs->vs_tpg); vs->vs_tpg = vs_tpg; If vhost_scsi_set_endpoint is called again and no tpgs are found match=false so we skip the vhost_vq_set_backend call leaving the pointer to the vs_tpg we then free via: kfree(vs->vs_tpg); vs->vs_tpg = vs_tpg; If a scsi request is then sent we do: vhost_scsi_handle_vq -> vhost_scsi_get_req -> vhost_vq_get_backend which sees the vs_tpg we just did a kfree on. 2. Tpg dir removal hang: This patch fixes an issue where we cannot remove a LIO/target layer tpg (and structs above it like the target) dir due to the refcount dropping to -1. The problem is that if vhost_scsi_set_endpoint detects a tpg is already in the vs->vs_tpg array or if the tpg has been removed so target_depend_item fails, the undepend goto handler will do target_undepend_item on all tpgs in the vs_tpg array dropping their refcount to 0. At this time vs_tpg contains both the tpgs we have added in the current vhost_scsi_set_endpoint call as well as tpgs we added in previous calls which are also in vs->vs_tpg. Later, when vhost_scsi_clear_endpoint runs it will do target_undepend_item on all the tpgs in the vs->vs_tpg which will drop their refcount to -1. Userspace will then not be able to remove the tpg and will hang when it tries to do rmdir on the tpg dir. 3. Tpg leak: This fixes a bug where we can leak tpgs and cause them to be un-removable because the target name is overwritten when vhost_scsi_set_endpoint is called multiple times but with different target names. The bug occurs if a user has called VHOST_SCSI_SET_ENDPOINT and setup a vhost-scsi device to target/tpg mapping, then calls VHOST_SCSI_SET_ENDPOINT again with a new target name that has tpgs we haven't seen before (target1 has tpg1 but target2 has tpg2). When this happens we don't teardown the old target tpg mapping and just overwrite the target name and the vs->vs_tpg array. Later when we do vhost_scsi_clear_endpoint, we are passed in either target1 or target2's name and we will only match that target's tpgs when we loop over the vs->vs_tpg. We will then return from the function without doing target_undepend_item on the tpgs. Because of all these bugs, it looks like being able to call vhost_scsi_set_endpoint multiple times was never supported. The major user, QEMU, already has checks to prevent this use case. So to fix the issues, this patch prevents vhost_scsi_set_endpoint from being called if it's already successfully added tpgs. To add, remove or change the tpg config or target name, you must do a vhost_scsi_clear_endpoint first.

There is a flaw reported in the Linux kernel in versions before 5.9 in drivers/gpu/drm/nouveau/nouveau_sgdma.c in nouveau_sgdma_create_ttm in Nouveau DRM subsystem. The issue results from the lack of validating the existence of an object prior to performing operations on the object. An attacker with a local account with a root privilege, can leverage this vulnerability to escalate privileges and execute code in the context of the kernel.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: do not force clear folio if buffer is referenced Patch series "nilfs2: protect busy buffer heads from being force-cleared". This series fixes the buffer head state inconsistency issues reported by syzbot that occurs when the filesystem is corrupted and falls back to read-only, and the associated buffer head use-after-free issue. This patch (of 2): Syzbot has reported that after nilfs2 detects filesystem corruption and falls back to read-only, inconsistencies in the buffer state may occur. One of the inconsistencies is that when nilfs2 calls mark_buffer_dirty() to set a data or metadata buffer as dirty, but it detects that the buffer is not in the uptodate state: WARNING: CPU: 0 PID: 6049 at fs/buffer.c:1177 mark_buffer_dirty+0x2e5/0x520 fs/buffer.c:1177 ... Call Trace: <TASK> nilfs_palloc_commit_alloc_entry+0x4b/0x160 fs/nilfs2/alloc.c:598 nilfs_ifile_create_inode+0x1dd/0x3a0 fs/nilfs2/ifile.c:73 nilfs_new_inode+0x254/0x830 fs/nilfs2/inode.c:344 nilfs_mkdir+0x10d/0x340 fs/nilfs2/namei.c:218 vfs_mkdir+0x2f9/0x4f0 fs/namei.c:4257 do_mkdirat+0x264/0x3a0 fs/namei.c:4280 __do_sys_mkdirat fs/namei.c:4295 [inline] __se_sys_mkdirat fs/namei.c:4293 [inline] __x64_sys_mkdirat+0x87/0xa0 fs/namei.c:4293 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f The other is when nilfs_btree_propagate(), which propagates the dirty state to the ancestor nodes of a b-tree that point to a dirty buffer, detects that the origin buffer is not dirty, even though it should be: WARNING: CPU: 0 PID: 5245 at fs/nilfs2/btree.c:2089 nilfs_btree_propagate+0xc79/0xdf0 fs/nilfs2/btree.c:2089 ... Call Trace: <TASK> nilfs_bmap_propagate+0x75/0x120 fs/nilfs2/bmap.c:345 nilfs_collect_file_data+0x4d/0xd0 fs/nilfs2/segment.c:587 nilfs_segctor_apply_buffers+0x184/0x340 fs/nilfs2/segment.c:1006 nilfs_segctor_scan_file+0x28c/0xa50 fs/nilfs2/segment.c:1045 nilfs_segctor_collect_blocks fs/nilfs2/segment.c:1216 [inline] nilfs_segctor_collect fs/nilfs2/segment.c:1540 [inline] nilfs_segctor_do_construct+0x1c28/0x6b90 fs/nilfs2/segment.c:2115 nilfs_segctor_construct+0x181/0x6b0 fs/nilfs2/segment.c:2479 nilfs_segctor_thread_construct fs/nilfs2/segment.c:2587 [inline] nilfs_segctor_thread+0x69e/0xe80 fs/nilfs2/segment.c:2701 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 </TASK> Both of these issues are caused by the callbacks that handle the page/folio write requests, forcibly clear various states, including the working state of the buffers they hold, at unexpected times when they detect read-only fallback. Fix these issues by checking if the buffer is referenced before clearing the page/folio state, and skipping the clear if it is.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: HWS, change error flow on matcher disconnect Currently, when firmware failure occurs during matcher disconnect flow, the error flow of the function reconnects the matcher back and returns an error, which continues running the calling function and eventually frees the matcher that is being disconnected. This leads to a case where we have a freed matcher on the matchers list, which in turn leads to use-after-free and eventual crash. This patch fixes that by not trying to reconnect the matcher back when some FW command fails during disconnect. Note that we're dealing here with FW error. We can't overcome this problem. This might lead to bad steering state (e.g. wrong connection between matchers), and will also lead to resource leakage, as it is the case with any other error handling during resource destruction. However, the goal here is to allow the driver to continue and not crash the machine with use-after-free error.

A use-after-free vulnerability in the Linux kernel's net/sched: sch_hfsc (HFSC qdisc traffic control) component can be exploited to achieve local privilege escalation. If a class with a link-sharing curve (i.e. with the HFSC_FSC flag set) has a parent without a link-sharing curve, then init_vf() will call vttree_insert() on the parent, but vttree_remove() will be skipped in update_vf(). This leaves a dangling pointer that can cause a use-after-free. We recommend upgrading past commit b3d26c5702c7d6c45456326e56d2ccf3f103e60f.

In the Linux kernel, the following vulnerability has been resolved: usb: usbtmc: Flush anchored URBs in usbtmc_release When calling usbtmc_release, pending anchored URBs must be flushed or killed to prevent use-after-free errors (e.g. in the HCD giveback path). Call usbtmc_draw_down() to allow anchored URBs to be completed.

In the Linux kernel, the following vulnerability has been resolved: net: lan966x: fix use-after-free and leak in lan966x_fdma_reload() When lan966x_fdma_reload() fails to allocate new RX buffers, the restore path restarts DMA using old descriptors whose pages were already freed via lan966x_fdma_rx_free_pages(). Since page_pool_put_full_page() can release pages back to the buddy allocator, the hardware may DMA into memory now owned by other kernel subsystems. Additionally, on the restore path, the newly created page pool (if allocation partially succeeded) is overwritten without being destroyed, leaking it. Fix both issues by deferring the release of old pages until after the new allocation succeeds. Save the old page array before the allocation so old pages can be freed on the success path. On the failure path, the old descriptors, pages and page pool are all still valid, making the restore safe. Also ensure the restore path re-enables NAPI and wakes the netdev, matching the success path.

In the Linux kernel, the following vulnerability has been resolved: xfs: avoid dereferencing log items after push callbacks After xfsaild_push_item() calls iop_push(), the log item may have been freed if the AIL lock was dropped during the push. Background inode reclaim or the dquot shrinker can free the log item while the AIL lock is not held, and the tracepoints in the switch statement dereference the log item after iop_push() returns. Fix this by capturing the log item type, flags, and LSN before calling xfsaild_push_item(), and introducing a new xfs_ail_push_class trace event class that takes these pre-captured values and the ailp pointer instead of the log item pointer.

In the Linux kernel, the following vulnerability has been resolved: bcache: fix cached_dev.sb_bio use-after-free and crash In our production environment, we have received multiple crash reports regarding libceph, which have caught our attention: ``` [6888366.280350] Call Trace: [6888366.280452] blk_update_request+0x14e/0x370 [6888366.280561] blk_mq_end_request+0x1a/0x130 [6888366.280671] rbd_img_handle_request+0x1a0/0x1b0 [rbd] [6888366.280792] rbd_obj_handle_request+0x32/0x40 [rbd] [6888366.280903] __complete_request+0x22/0x70 [libceph] [6888366.281032] osd_dispatch+0x15e/0xb40 [libceph] [6888366.281164] ? inet_recvmsg+0x5b/0xd0 [6888366.281272] ? ceph_tcp_recvmsg+0x6f/0xa0 [libceph] [6888366.281405] ceph_con_process_message+0x79/0x140 [libceph] [6888366.281534] ceph_con_v1_try_read+0x5d7/0xf30 [libceph] [6888366.281661] ceph_con_workfn+0x329/0x680 [libceph] ``` After analyzing the coredump file, we found that the address of dc->sb_bio has been freed. We know that cached_dev is only freed when it is stopped. Since sb_bio is a part of struct cached_dev, rather than an alloc every time. If the device is stopped while writing to the superblock, the released address will be accessed at endio. This patch hopes to wait for sb_write to complete in cached_dev_free. It should be noted that we analyzed the cause of the problem, then tell all details to the QWEN and adopted the modifications it made.

In the Linux kernel, the following vulnerability has been resolved: writeback: Fix use after free in inode_switch_wbs_work_fn() inode_switch_wbs_work_fn() has a loop like: wb_get(new_wb); while (1) { list = llist_del_all(&new_wb->switch_wbs_ctxs); /* Nothing to do? */ if (!list) break; ... process the items ... } Now adding of items to the list looks like: wb_queue_isw() if (llist_add(&isw->list, &wb->switch_wbs_ctxs)) queue_work(isw_wq, &wb->switch_work); Because inode_switch_wbs_work_fn() loops when processing isw items, it can happen that wb->switch_work is pending while wb->switch_wbs_ctxs is empty. This is a problem because in that case wb can get freed (no isw items -> no wb reference) while the work is still pending causing use-after-free issues. We cannot just fix this by cancelling work when freeing wb because that could still trigger problematic 0 -> 1 transitions on wb refcount due to wb_get() in inode_switch_wbs_work_fn(). It could be all handled with more careful code but that seems unnecessarily complex so let's avoid that until it is proven that the looping actually brings practical benefit. Just remove the loop from inode_switch_wbs_work_fn() instead. That way when wb_queue_isw() queues work, we are guaranteed we have added the first item to wb->switch_wbs_ctxs and nobody is going to remove it (and drop the wb reference it holds) until the queued work runs.

In the Linux kernel, the following vulnerability has been resolved: cxl/port: Fix use after free of parent_port in cxl_detach_ep() cxl_detach_ep() is called during bottom-up removal when all CXL memory devices beneath a switch port have been removed. For each port in the hierarchy it locks both the port and its parent, removes the endpoint, and if the port is now empty, marks it dead and unregisters the port by calling delete_switch_port(). There are two places during this work where the parent_port may be used after freeing: First, a concurrent detach may have already processed a port by the time a second worker finds it via bus_find_device(). Without pinning parent_port, it may already be freed when we discover port->dead and attempt to unlock the parent_port. In a production kernel that's a silent memory corruption, with lock debug, it looks like this: []DEBUG_LOCKS_WARN_ON(__owner_task(owner) != get_current()) []WARNING: kernel/locking/mutex.c:949 at __mutex_unlock_slowpath+0x1ee/0x310 []Call Trace: []mutex_unlock+0xd/0x20 []cxl_detach_ep+0x180/0x400 [cxl_core] []devm_action_release+0x10/0x20 []devres_release_all+0xa8/0xe0 []device_unbind_cleanup+0xd/0xa0 []really_probe+0x1a6/0x3e0 Second, delete_switch_port() releases three devm actions registered against parent_port. The last of those is unregister_port() and it calls device_unregister() on the child port, which can cascade. If parent_port is now also empty the device core may unregister and free it too. So by the time delete_switch_port() returns, parent_port may be free, and the subsequent device_unlock(&parent_port->dev) operates on freed memory. The kernel log looks same as above, with a different offset in cxl_detach_ep(). Both of these issues stem from the absence of a lifetime guarantee between a child port and its parent port. Establish a lifetime rule for ports: child ports hold a reference to their parent device until release. Take the reference when the port is allocated and drop it when released. This ensures the parent is valid for the full lifetime of the child and eliminates the use after free window in cxl_detach_ep(). This is easily reproduced with a reload of cxl_acpi in QEMU with CXL devices present.

In the Linux kernel, the following vulnerability has been resolved: wifi: virt_wifi: remove SET_NETDEV_DEV to avoid use-after-free Currently we execute `SET_NETDEV_DEV(dev, &priv->lowerdev->dev)` for the virt_wifi net devices. However, unregistering a virt_wifi device in netdev_run_todo() can happen together with the device referenced by SET_NETDEV_DEV(). It can result in use-after-free during the ethtool operations performed on a virt_wifi device that is currently being unregistered. Such a net device can have the `dev.parent` field pointing to the freed memory, but ethnl_ops_begin() calls `pm_runtime_get_sync(dev->dev.parent)`. Let's remove SET_NETDEV_DEV for virt_wifi to avoid bugs like this: ================================================================== BUG: KASAN: slab-use-after-free in __pm_runtime_resume+0xe2/0xf0 Read of size 2 at addr ffff88810cfc46f8 by task pm/606 Call Trace: <TASK> dump_stack_lvl+0x4d/0x70 print_report+0x170/0x4f3 ? __pfx__raw_spin_lock_irqsave+0x10/0x10 kasan_report+0xda/0x110 ? __pm_runtime_resume+0xe2/0xf0 ? __pm_runtime_resume+0xe2/0xf0 __pm_runtime_resume+0xe2/0xf0 ethnl_ops_begin+0x49/0x270 ethnl_set_features+0x23c/0xab0 ? __pfx_ethnl_set_features+0x10/0x10 ? kvm_sched_clock_read+0x11/0x20 ? local_clock_noinstr+0xf/0xf0 ? local_clock+0x10/0x30 ? kasan_save_track+0x25/0x60 ? __kasan_kmalloc+0x7f/0x90 ? genl_family_rcv_msg_attrs_parse.isra.0+0x150/0x2c0 genl_family_rcv_msg_doit+0x1e7/0x2c0 ? __pfx_genl_family_rcv_msg_doit+0x10/0x10 ? __pfx_cred_has_capability.isra.0+0x10/0x10 ? stack_trace_save+0x8e/0xc0 genl_rcv_msg+0x411/0x660 ? __pfx_genl_rcv_msg+0x10/0x10 ? __pfx_ethnl_set_features+0x10/0x10 netlink_rcv_skb+0x121/0x380 ? __pfx_genl_rcv_msg+0x10/0x10 ? __pfx_netlink_rcv_skb+0x10/0x10 ? __pfx_down_read+0x10/0x10 genl_rcv+0x23/0x30 netlink_unicast+0x60f/0x830 ? __pfx_netlink_unicast+0x10/0x10 ? __pfx___alloc_skb+0x10/0x10 netlink_sendmsg+0x6ea/0xbc0 ? __pfx_netlink_sendmsg+0x10/0x10 ? __futex_queue+0x10b/0x1f0 ____sys_sendmsg+0x7a2/0x950 ? copy_msghdr_from_user+0x26b/0x430 ? __pfx_____sys_sendmsg+0x10/0x10 ? __pfx_copy_msghdr_from_user+0x10/0x10 ___sys_sendmsg+0xf8/0x180 ? __pfx____sys_sendmsg+0x10/0x10 ? __pfx_futex_wait+0x10/0x10 ? fdget+0x2e4/0x4a0 __sys_sendmsg+0x11f/0x1c0 ? __pfx___sys_sendmsg+0x10/0x10 do_syscall_64+0xe2/0x570 ? exc_page_fault+0x66/0xb0 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> This fix may be combined with another one in the ethtool subsystem: https://lore.kernel.org/all/20260322075917.254874-1-alex.popov@linux.com/T/#u

In the Linux kernel, the following vulnerability has been resolved: xfs: stop reclaim before pushing AIL during unmount The unmount sequence in xfs_unmount_flush_inodes() pushed the AIL while background reclaim and inodegc are still running. This is broken independently of any use-after-free issues - background reclaim and inodegc should not be running while the AIL is being pushed during unmount, as inodegc can dirty and insert inodes into the AIL during the flush, and background reclaim can race to abort and free dirty inodes. Reorder xfs_unmount_flush_inodes() to stop inodegc and cancel background reclaim before pushing the AIL. Stop inodegc before cancelling m_reclaim_work because the inodegc worker can re-queue m_reclaim_work via xfs_inodegc_set_reclaimable.

In the Linux kernel, the following vulnerability has been resolved: net: fix fanout UAF in packet_release() via NETDEV_UP race `packet_release()` has a race window where `NETDEV_UP` can re-register a socket into a fanout group's `arr[]` array. The re-registration is not cleaned up by `fanout_release()`, leaving a dangling pointer in the fanout array. `packet_release()` does NOT zero `po->num` in its `bind_lock` section. After releasing `bind_lock`, `po->num` is still non-zero and `po->ifindex` still matches the bound device. A concurrent `packet_notifier(NETDEV_UP)` that already found the socket in `sklist` can re-register the hook. For fanout sockets, this re-registration calls `__fanout_link(sk, po)` which adds the socket back into `f->arr[]` and increments `f->num_members`, but does NOT increment `f->sk_ref`. The fix sets `po->num` to zero in `packet_release` while `bind_lock` is held to prevent NETDEV_UP from linking, preventing the race window. This bug was found following an additional audit with Claude Code based on CVE-2025-38617.

In the Linux kernel, the following vulnerability has been resolved: tracing: Fix trace_marker copy link list updates When the "copy_trace_marker" option is enabled for an instance, anything written into /sys/kernel/tracing/trace_marker is also copied into that instances buffer. When the option is set, that instance's trace_array descriptor is added to the marker_copies link list. This list is protected by RCU, as all iterations uses an RCU protected list traversal. When the instance is deleted, all the flags that were enabled are cleared. This also clears the copy_trace_marker flag and removes the trace_array descriptor from the list. The issue is after the flags are called, a direct call to update_marker_trace() is performed to clear the flag. This function returns true if the state of the flag changed and false otherwise. If it returns true here, synchronize_rcu() is called to make sure all readers see that its removed from the list. But since the flag was already cleared, the state does not change and the synchronization is never called, leaving a possible UAF bug. Move the clearing of all flags below the updating of the copy_trace_marker option which then makes sure the synchronization is performed. Also use the flag for checking the state in update_marker_trace() instead of looking at if the list is empty.

In the Linux kernel, the following vulnerability has been resolved: mm: blk-cgroup: fix use-after-free in cgwb_release_workfn() cgwb_release_workfn() calls css_put(wb->blkcg_css) and then later accesses wb->blkcg_css again via blkcg_unpin_online(). If css_put() drops the last reference, the blkcg can be freed asynchronously (css_free_rwork_fn -> blkcg_css_free -> kfree) before blkcg_unpin_online() dereferences the pointer to access blkcg->online_pin, resulting in a use-after-free: BUG: KASAN: slab-use-after-free in blkcg_unpin_online (./include/linux/instrumented.h:112 ./include/linux/atomic/atomic-instrumented.h:400 ./include/linux/refcount.h:389 ./include/linux/refcount.h:432 ./include/linux/refcount.h:450 block/blk-cgroup.c:1367) Write of size 4 at addr ff11000117aa6160 by task kworker/71:1/531 Workqueue: cgwb_release cgwb_release_workfn Call Trace: <TASK> blkcg_unpin_online (./include/linux/instrumented.h:112 ./include/linux/atomic/atomic-instrumented.h:400 ./include/linux/refcount.h:389 ./include/linux/refcount.h:432 ./include/linux/refcount.h:450 block/blk-cgroup.c:1367) cgwb_release_workfn (mm/backing-dev.c:629) process_scheduled_works (kernel/workqueue.c:3278 kernel/workqueue.c:3385) Freed by task 1016: kfree (./include/linux/kasan.h:235 mm/slub.c:2689 mm/slub.c:6246 mm/slub.c:6561) css_free_rwork_fn (kernel/cgroup/cgroup.c:5542) process_scheduled_works (kernel/workqueue.c:3302 kernel/workqueue.c:3385) ** Stack based on commit 66672af7a095 ("Add linux-next specific files for 20260410") I am seeing this crash sporadically in Meta fleet across multiple kernel versions. A full reproducer is available at: https://github.com/leitao/debug/blob/main/reproducers/repro_blkcg_uaf.sh (The race window is narrow. To make it easily reproducible, inject a msleep(100) between css_put() and blkcg_unpin_online() in cgwb_release_workfn(). With that delay and a KASAN-enabled kernel, the reproducer triggers the splat reliably in less than a second.) Fix this by moving blkcg_unpin_online() before css_put(), so the cgwb's CSS reference keeps the blkcg alive while blkcg_unpin_online() accesses it.

In the Linux kernel, the following vulnerability has been resolved: media: em28xx: fix use-after-free in em28xx_v4l2_open() em28xx_v4l2_open() reads dev->v4l2 without holding dev->lock, creating a race with em28xx_v4l2_init()'s error path and em28xx_v4l2_fini(), both of which free the em28xx_v4l2 struct and set dev->v4l2 to NULL under dev->lock. This race leads to two issues: - use-after-free in v4l2_fh_init() when accessing vdev->ctrl_handler, since the video_device is embedded in the freed em28xx_v4l2 struct. - NULL pointer dereference in em28xx_resolution_set() when accessing v4l2->norm, since dev->v4l2 has been set to NULL. Fix this by moving the mutex_lock() before the dev->v4l2 read and adding a NULL check for dev->v4l2 under the lock.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix fence put before wait in amdgpu_amdkfd_submit_ib amdgpu_amdkfd_submit_ib() submits a GPU job and gets a fence from amdgpu_ib_schedule(). This fence is used to wait for job completion. Currently, the code drops the fence reference using dma_fence_put() before calling dma_fence_wait(). If dma_fence_put() releases the last reference, the fence may be freed before dma_fence_wait() is called. This can lead to a use-after-free. Fix this by waiting on the fence first and releasing the reference only after dma_fence_wait() completes. Fixes the below: drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd.c:697 amdgpu_amdkfd_submit_ib() warn: passing freed memory 'f' (line 696) (cherry picked from commit 8b9e5259adc385b61a6590a13b82ae0ac2bd3482)

In the Linux kernel, the following vulnerability has been resolved: ocfs2: fix use-after-free in ocfs2_fault() when VM_FAULT_RETRY filemap_fault() may drop the mmap_lock before returning VM_FAULT_RETRY, as documented in mm/filemap.c: "If our return value has VM_FAULT_RETRY set, it's because the mmap_lock may be dropped before doing I/O or by lock_folio_maybe_drop_mmap()." When this happens, a concurrent munmap() can call remove_vma() and free the vm_area_struct via RCU. The saved 'vma' pointer in ocfs2_fault() then becomes a dangling pointer, and the subsequent trace_ocfs2_fault() call dereferences it -- a use-after-free. Fix this by saving ip_blkno as a plain integer before calling filemap_fault(), and removing vma from the trace event. Since ip_blkno is copied by value before the lock can be dropped, it remains valid regardless of what happens to the vma or inode afterward.

In the Linux kernel, the following vulnerability has been resolved: RDMA/efa: Fix use of completion ctx after free On admin queue completion handling, if the admin command completed with error we print data from the completion context. The issue is that we already freed the completion context in polling/interrupts handler which means we print data from context in an unknown state (it might be already used again). Change the admin submission flow so alloc/dealloc of the context will be symmetric and dealloc will be called after any potential use of the context.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: MGMT: Fix dangling pointer on mgmt_add_adv_patterns_monitor_complete This fixes the condition checking so mgmt_pending_valid is executed whenever status != -ECANCELED otherwise calling mgmt_pending_free(cmd) would kfree(cmd) without unlinking it from the list first, leaving a dangling pointer. Any subsequent list traversal (e.g., mgmt_pending_foreach during __mgmt_power_off, or another mgmt_pending_valid call) would dereference freed memory.

In the Linux kernel, the following vulnerability has been resolved: driver core: enforce device_lock for driver_match_device() Currently, driver_match_device() is called from three sites. One site (__device_attach_driver) holds device_lock(dev), but the other two (bind_store and __driver_attach) do not. This inconsistency means that bus match() callbacks are not guaranteed to be called with the lock held. Fix this by introducing driver_match_device_locked(), which guarantees holding the device lock using a scoped guard. Replace the unlocked calls in bind_store() and __driver_attach() with this new helper. Also add a lock assertion to driver_match_device() to enforce this guarantee. This consistency also fixes a known race condition. The driver_override implementation relies on the device_lock, so the missing lock led to the use-after-free (UAF) reported in Bugzilla for buses using this field. Stress testing the two newly locked paths for 24 hours with CONFIG_PROVE_LOCKING and CONFIG_LOCKDEP enabled showed no UAF recurrence and no lockdep warnings.

In the Linux kernel, the following vulnerability has been resolved: can: isotp: fix tx.buf use-after-free in isotp_sendmsg() isotp_sendmsg() uses only cmpxchg() on so->tx.state to serialize access to so->tx.buf. isotp_release() waits for ISOTP_IDLE via wait_event_interruptible() and then calls kfree(so->tx.buf). If a signal interrupts the wait_event_interruptible() inside close() while tx.state is ISOTP_SENDING, the loop exits early and release proceeds to force ISOTP_SHUTDOWN and continues to kfree(so->tx.buf) while sendmsg may still be reading so->tx.buf for the final CAN frame in isotp_fill_dataframe(). The so->tx.buf can be allocated once when the standard tx.buf length needs to be extended. Move the kfree() of this potentially extended tx.buf to sk_destruct time when either isotp_sendmsg() and isotp_release() are done.

A use-after-free vulnerability in the Linux kernel's netfilter: nf_tables component can be exploited to achieve local privilege escalation. Due to a race condition between nf_tables netlink control plane transaction and nft_set element garbage collection, it is possible to underflow the reference counter causing a use-after-free vulnerability. We recommend upgrading past commit 3e91b0ebd994635df2346353322ac51ce84ce6d8.

In the Linux kernel, the following vulnerability has been resolved: futex: Require sys_futex_requeue() to have identical flags Nicholas reported that his LLM found it was possible to create a UaF when sys_futex_requeue() is used with different flags. The initial motivation for allowing different flags was the variable sized futex, but since that hasn't been merged (yet), simply mandate the flags are identical, as is the case for the old style sys_futex() requeue operations.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/pf: Fix use-after-free in migration restore When an error is returned from xe_sriov_pf_migration_restore_produce(), the data pointer is not set to NULL, which can trigger use-after-free in subsequent .write() calls. Set the pointer to NULL upon error to fix the problem. (cherry picked from commit 4f53d8c6d23527d734fe3531d08e15cb170a0819)

In the Linux kernel, the following vulnerability has been resolved: xfs: save ailp before dropping the AIL lock in push callbacks In xfs_inode_item_push() and xfs_qm_dquot_logitem_push(), the AIL lock is dropped to perform buffer IO. Once the cluster buffer no longer protects the log item from reclaim, the log item may be freed by background reclaim or the dquot shrinker. The subsequent spin_lock() call dereferences lip->li_ailp, which is a use-after-free. Fix this by saving the ailp pointer in a local variable while the AIL lock is held and the log item is guaranteed to be valid.

In the Linux kernel, the following vulnerability has been resolved: can: raw: fix ro->uniq use-after-free in raw_rcv() raw_release() unregisters raw CAN receive filters via can_rx_unregister(), but receiver deletion is deferred with call_rcu(). This leaves a window where raw_rcv() may still be running in an RCU read-side critical section after raw_release() frees ro->uniq, leading to a use-after-free of the percpu uniq storage. Move free_percpu(ro->uniq) out of raw_release() and into a raw-specific socket destructor. can_rx_unregister() takes an extra reference to the socket and only drops it from the RCU callback, so freeing uniq from sk_destruct ensures the percpu area is not released until the relevant callbacks have drained. [mkl: applied manually]

In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_ct: fix use-after-free in timeout object destroy nft_ct_timeout_obj_destroy() frees the timeout object with kfree() immediately after nf_ct_untimeout(), without waiting for an RCU grace period. Concurrent packet processing on other CPUs may still hold RCU-protected references to the timeout object obtained via rcu_dereference() in nf_ct_timeout_data(). Add an rcu_head to struct nf_ct_timeout and use kfree_rcu() to defer freeing until after an RCU grace period, matching the approach already used in nfnetlink_cttimeout.c. KASAN report: BUG: KASAN: slab-use-after-free in nf_conntrack_tcp_packet+0x1381/0x29d0 Read of size 4 at addr ffff8881035fe19c by task exploit/80 Call Trace: nf_conntrack_tcp_packet+0x1381/0x29d0 nf_conntrack_in+0x612/0x8b0 nf_hook_slow+0x70/0x100 __ip_local_out+0x1b2/0x210 tcp_sendmsg_locked+0x722/0x1580 __sys_sendto+0x2d8/0x320 Allocated by task 75: nft_ct_timeout_obj_init+0xf6/0x290 nft_obj_init+0x107/0x1b0 nf_tables_newobj+0x680/0x9c0 nfnetlink_rcv_batch+0xc29/0xe00 Freed by task 26: nft_obj_destroy+0x3f/0xa0 nf_tables_trans_destroy_work+0x51c/0x5c0 process_one_work+0x2c4/0x5a0

In the Linux kernel, the following vulnerability has been resolved: ALSA: 6fire: fix use-after-free on disconnect In usb6fire_chip_abort(), the chip struct is allocated as the card's private data (via snd_card_new with sizeof(struct sfire_chip)). When snd_card_free_when_closed() is called and no file handles are open, the card and embedded chip are freed synchronously. The subsequent chip->card = NULL write then hits freed slab memory. Call trace: usb6fire_chip_abort sound/usb/6fire/chip.c:59 [inline] usb6fire_chip_disconnect+0x348/0x358 sound/usb/6fire/chip.c:182 usb_unbind_interface+0x1a8/0x88c drivers/usb/core/driver.c:458 ... hub_event+0x1a04/0x4518 drivers/usb/core/hub.c:5953 Fix by moving the card lifecycle out of usb6fire_chip_abort() and into usb6fire_chip_disconnect(). The card pointer is saved in a local before any teardown, snd_card_disconnect() is called first to prevent new opens, URBs are aborted while chip is still valid, and snd_card_free_when_closed() is called last so chip is never accessed after the card may be freed.

In the Linux kernel, the following vulnerability has been resolved: mm/damon/stat: deallocate damon_call() failure leaking damon_ctx damon_stat_start() always allocates the module's damon_ctx object (damon_stat_context). Meanwhile, if damon_call() in the function fails, the damon_ctx object is not deallocated. Hence, if the damon_call() is failed, and the user writes Y to “enabled” again, the previously allocated damon_ctx object is leaked. This cannot simply be fixed by deallocating the damon_ctx object when damon_call() fails. That's because damon_call() failure doesn't guarantee the kdamond main function, which accesses the damon_ctx object, is completely finished. In other words, if damon_stat_start() deallocates the damon_ctx object after damon_call() failure, the not-yet-terminated kdamond could access the freed memory (use-after-free). Fix the leak while avoiding the use-after-free by keeping returning damon_stat_start() without deallocating the damon_ctx object after damon_call() failure, but deallocating it when the function is invoked again and the kdamond is completely terminated. If the kdamond is not yet terminated, simply return -EAGAIN, as the kdamond will soon be terminated. The issue was discovered [1] by sashiko.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (powerz) Fix use-after-free on USB disconnect After powerz_disconnect() frees the URB and releases the mutex, a subsequent powerz_read() call can acquire the mutex and call powerz_read_data(), which dereferences the freed URB pointer. Fix by: - Setting priv->urb to NULL in powerz_disconnect() so that powerz_read_data() can detect the disconnected state. - Adding a !priv->urb check at the start of powerz_read_data() to return -ENODEV on a disconnected device. - Moving usb_set_intfdata() before hwmon registration so the disconnect handler can always find the priv pointer.

In the Linux kernel, the following vulnerability has been resolved: media: mc, v4l2: serialize REINIT and REQBUFS with req_queue_mutex MEDIA_REQUEST_IOC_REINIT can run concurrently with VIDIOC_REQBUFS(0) queue teardown paths. This can race request object cleanup against vb2 queue cancellation and lead to use-after-free reports. We already serialize request queueing against STREAMON/OFF with req_queue_mutex. Extend that serialization to REQBUFS, and also take the same mutex in media_request_ioctl_reinit() so REINIT is in the same exclusion domain. This keeps request cleanup and queue cancellation from running in parallel for request-capable devices.