An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated networked attacker to cause a Denial of Service (DoS) by sending specific packets over VXLAN which cause the PFE to reset. This issue affects: Juniper Networks Junos OS 19.4 versions prior to 19.4R3-S7; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S1; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R2; 21.3 versions prior to 21.3R1-S1, 21.3R2. This issue does not affect versions of Junos OS prior to 19.4R1.
An always-incorrect control flow implementation in the implicit filter terms of Juniper Networks Junos OS and Junos OS Evolved on ACX5800, EX9200 Series, MX10000 Series, MX240, MX480, MX960 devices with affected Trio line cards allows an attacker to exploit an interdependency in the PFE UCODE microcode of the Trio chipset with various line cards to cause packets destined to the devices interfaces to cause a Denial of Service (DoS) condition by looping the packet with an unreachable exit condition ('Infinite Loop'). To break this loop once it begins one side of the affected LT interfaces will need to be disabled. Once disabled, the condition will clear and the disabled LT interface can be reenabled. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue only affects LT-LT interfaces. Any other interfaces are not affected by this issue. This issue affects the following cards: MPCE Type 3 3D MPC4E 3D 32XGE MPC4E 3D 2CGE+8XGE EX9200 32x10G SFP EX9200-2C-8XS FPC Type 5-3D FPC Type 5-LSR EX9200 4x40G QSFP An Indicator of Compromise (IoC) can be seen by examining the traffic of the LT-LT interfaces for excessive traffic using the following command: monitor interface traffic Before loop impact: Interface: lt-2/0/0, Enabled, Link is Up Encapsulation: Logical-tunnel, Speed: 100000mbps Traffic statistics: Current delta Input bytes: 3759900268942 (1456 bps) [0] <---------- LT interface utilization is low Output bytes: 3759900344309 (1456 bps) [0] <---------- LT interface utilization is low After loop impact: Interface: lt-2/0/0, Enabled, Link is Up Encapsulation: Logical-tunnel, Speed: 100000mbps Traffic statistics: Current delta Input bytes: 3765160313129 (2158268368 bps) [5260044187] <---------- LT interface utilization is very high Output bytes: 3765160399522 (2158266440 bps) [5260055213] <---------- LT interface utilization is very high This issue affects: Juniper Networks Junos OS on ACX5800, EX9200 Series, MX10000 Series, MX240, MX480, MX960. Versions 15.1F6, 16.1R1, and later versions prior to 16.1R7-S8; 17.1 versions prior to 17.1R2-S12; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R1-S7, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S4, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S1, 19.4R2. This issue does not affect the MX10001. This issue does not affect Juniper Networks Junos OS versions prior to 15.1F6, 16.1R1. Juniper Networks Junos OS Evolved on ACX5800, EX9200 Series, MX10000 Series, MX240, MX480, MX960 19.4 versions prior to 19.4R2-EVO. This issue does not affect the MX10001.
When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of small fragments requiring reassembly, generating the following error messages: [LOG: Err] MQSS(2): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[2:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(2): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1960, QID 0 [LOG: Err] MQSS(2): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0xc38fb1 [LOG: Notice] Error: /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(2), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S9, 17.4R3-S1 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D34, 18.2X75-D41, 18.2X75-D53, 18.2X75-D65, 18.2X75-D430 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S2 on MX Series; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.
On Juniper Networks MX Series and EX9200 Series, in a certain condition the IPv6 Distributed Denial of Service (DDoS) protection might not take affect when it reaches the threshold condition. The DDoS protection allows the device to continue to function while it is under DDoS attack, protecting both the Routing Engine (RE) and the Flexible PIC Concentrator (FPC) during the DDoS attack. When this issue occurs, the RE and/or the FPC can become overwhelmed, which could disrupt network protocol operations and/or interrupt traffic. This issue does not affect IPv4 DDoS protection. This issue affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines). Please refer to https://kb.juniper.net/KB25385 for the list of Trio-based PFEs. This issue affects Juniper Networks Junos OS on MX series and EX9200 Series: 17.2 versions prior to 17.2R3-S4; 17.2X75 versions prior to 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.2 versions prior to 18.2R2-S7, 18.2R3, 18.2R3-S3; 18.2X75 versions prior to 18.2X75-D30; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2.
A vulnerability in Juniper Networks Junos OS Evolved may allow an attacker to cause a Denial of Service (DoS) by sending a high rate of specific packets to the device, resulting in a pfemand process crash. The pfemand process is responsible for packet forwarding on the device. By continuously sending the packet flood, an attacker can repeatedly crash the pfemand process causing a sustained Denial of Service. This issue can only be triggered by traffic sent to the device. Transit traffic does not cause this issue. This issue affects all version of Junos OS Evolved prior to 19.1R1-EVO.
On Juniper Networks MX Series with MS-MIC or MS-MPC card configured with NAT64 configuration, receipt of a malformed IPv6 packet may crash the MS-PIC component on MS-MIC or MS-MPC. This issue occurs when a multiservice card is translating the malformed IPv6 packet to IPv4 packet. An unauthenticated attacker can continuously send crafted IPv6 packets through the device causing repetitive MS-PIC process crashes, resulting in an extended Denial of Service condition. This issue affects Juniper Networks Junos OS on MX Series: 15.1 versions prior to 15.1R7-S7; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S8; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S6; 17.4 versions prior to 17.4R2-S11, 17.4R3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D430, 18.2X75-D53, 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3; 18.4 versions prior to 18.4R2-S5, 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2.
On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific BGP packet can lead to a routing process daemon (RPD) crash and restart. This issue can occur even before the BGP session with the peer is established. Repeated receipt of this specific BGP packet can result in an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 18.2X75 versions starting from 18.2X75-D50.8, 18.2X75-D60 and later versions, prior to 18.2X75-D52.8, 18.2X75-D53, 18.2X75-D60.2, 18.2X75-D65.1, 18.2X75-D70; 19.4 versions 19.4R1 and 19.4R1-S1; 20.1 versions prior to 20.1R1-S2, 20.1R2. Juniper Networks Junos OS Evolved: 19.4-EVO versions prior to 19.4R2-S2-EVO; 20.1-EVO versions prior to 20.1R2-EVO. This issue does not affect: Juniper Networks Junos OS releases prior to 19.4R1. Juniper Networks Junos OS Evolved releases prior to 19.4R1-EVO.
A vulnerability in the processing of inbound IPv6 packets in Juniper Networks Junos OS on QFX5000 Series and EX4600 switches may cause the memory to not be freed, leading to a packet DMA memory leak, and eventual Denial of Service (DoS) condition. Once the condition occurs, further packet processing will be impacted, creating a sustained Denial of Service (DoS) condition. The following error logs may be observed using the "show heap" command and the device may eventually run out of memory if such packets are received continuously. Jan 12 12:00:00 device-name fpc0 (buf alloc) failed allocating packet buffer Jan 12 12:00:01 device-name fpc0 (buf alloc) failed allocating packet buffer user@device-name> request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 246fc1a8 536870488 353653752 183216736 34 Kernel 1 91800000 16777216 12069680 4707536 28 DMA 2 92800000 75497472 69997640 5499832 7 PKT DMA DESC 3 106fc000 335544320 221425960 114118360 34 Bcm_sdk 4 97000000 176160768 200 176160568 99 Packet DMA <<<<<<<<<<<<<< 5 903fffe0 20971504 20971504 0 0 Blob This issue affects Juniper Networks Junos OS on QFX5000 Series, EX4600: 18.3R3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S6; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue does not affect Juniper Networks Junos OS: Any versions prior to 17.4R3; 18.1 versions prior to 18.1R3-S6; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R2.
On Juniper Networks Junos MX Series with service card configured, receipt of a stream of specific packets may crash the MS-PIC component on MS-MIC or MS-MPC. By continuously sending these specific packets, an attacker can repeatedly bring down MS-PIC on MS-MIC/MS-MPC causing a prolonged Denial of Service. This issue affects MX Series devices using MS-PIC, MS-MIC or MS-MPC service cards with any service configured. This issue affects Juniper Networks Junos OS on MX Series: 17.2R2-S7; 17.3R3-S4, 17.3R3-S5; 17.4R2-S4 and the subsequent SRs (17.4R2-S5, 17.4R2-S6, etc.); 17.4R3; 18.1R3-S3, 18.1R3-S4, 18.1R3-S5, 18.1R3-S6, 18.1R3-S7, 18.1R3-S8; 18.2R3, 18.2R3-S1, 18.2R3-S2; 18.3R2 and the SRs based on 18.3R2; 18.4R2 and the SRs based on 18.4R2; 19.1R1 and the SRs based on 19.1R1; 19.2R1 and the SRs based on 19.2R1; 19.3R1 and the SRs based on 19.3R1.
The FPC (Flexible PIC Concentrator) of Juniper Networks Junos OS and Junos OS Evolved may restart after processing a specific IPv4 packet. Only packets destined to the device itself, successfully reaching the RE through existing edge and control plane filtering, will be able to cause the FPC restart. When this issue occurs, all traffic via the FPC will be dropped. By continuously sending this specific IPv4 packet, an attacker can repeatedly crash the FPC, causing an extended Denial of Service (DoS) condition. This issue can only occur when processing a specific IPv4 packet. IPv6 packets cannot trigger this issue. This issue affects: Juniper Networks Junos OS on MX Series with MPC10E or MPC11E and PTX10001: 19.2 versions prior to 19.2R1-S4, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S1, 19.4R2. Juniper Networks Junos OS Evolved on on QFX5220, and PTX10003 series: 19.2-EVO versions; 19.3-EVO versions; 19.4-EVO versions prior to 19.4R2-EVO. This issue does not affect Junos OS versions prior to 19.2R1. This issue does not affect Junos OS Evolved versions prior to 19.2R1-EVO.
An Improper Check for Unusual or Exceptional Conditions vulnerability in the processing of specific IPv6 packets on certain EX Series devices may lead to exhaustion of DMA memory causing a Denial of Service (DoS). Over time, exploitation of this vulnerability may cause traffic to stop being forwarded, or a crash of the fxpc process. An indication of the issue occurring may be observed through the following log messages: Sep 13 17:14:59 hostname : %PFE-3: fpc0 (buf alloc) failed allocating packet buffer Sep 13 17:14:59 hostname : %PFE-7: fpc0 brcm_pkt_buf_alloc:393 (buf alloc) failed allocating packet buffer When Packet DMA heap utilization reaches 99%, the system will become unstable. Packet DMA heap utilization can be monitored using the command: user@junos# request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 213301a8 536870488 387228840 149641648 27 Kernel 1 91800000 8388608 3735120 4653488 55 DMA 2 92000000 75497472 74452192 1045280 1 PKT DMA DESC 3 d330000 335544320 257091400 78452920 23 Bcm_sdk 4 96800000 184549376 2408 184546968 99 Packet DMA <<<< 5 903fffe0 20971504 20971504 0 0 Blob This issue affects: Juniper Networks Junos OS 18.4 versions prior to 18.4R2-S10, 18.4R3-S10 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.1 versions prior to 19.1R3-S7 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.3 versions prior to 19.3R3-S5 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.4 versions prior to 19.4R3-S7 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.1 versions prior to 20.1R3-S3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.2 versions prior to 20.2R3-S3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.3 versions prior to 20.3R3-S2 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.4 versions prior to 20.4R3-S1 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.1 versions prior to 21.1R2-S2, 21.1R3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.2 versions prior to 21.2R1-S2, 21.2R2 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.3 versions prior to 21.3R1-S1, 21.3R2 on EX2300 Series, EX2300-MP Series, EX3400 Series.
On SRX Series devices, a vulnerability in the key-management-daemon (kmd) daemon of Juniper Networks Junos OS allows an attacker to spoof packets targeted to IPSec peers before a security association (SA) is established thereby causing a failure to set up the IPSec channel. Sustained receipt of these spoofed packets can cause a sustained Denial of Service (DoS) condition. This issue affects IPv4 and IPv6 implementations. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D90; 15.1X49 versions prior to 15.1X49-D190; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S6, 18.4R2-S3, 18.4R3; 19.1 versions prior to 19.1R1-S4, 19.1R2. This issue does not affect 12.3 or 15.1 releases which are non-SRX Series releases.
A Missing Release of Memory after Effective Lifetime vulnerability in the Public Key Infrastructure daemon (pkid) of Juniper Networks Junos OS allows an unauthenticated networked attacker to cause Denial of Service (DoS). In a scenario where Public Key Infrastructure (PKI) is used in combination with Certificate Revocation List (CRL), if the CRL fails to download the memory allocated to store the CRL is not released. Repeated occurrences will eventually consume all available memory and lead to an inoperable state of the affected system causing a DoS. This issue affects Juniper Networks Junos OS: All versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S10; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S5; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue can be observed by monitoring the memory utilization of the pkid process via: root@jtac-srx1500-r2003> show system processes extensive | match pki 20931 root 20 0 733M 14352K select 0:00 0.00% pkid which increases over time: root@jtac-srx1500-r2003> show system processes extensive | match pki 22587 root 20 0 901M 181M select 0:03 0.00% pkid
An Insufficient Algorithmic Complexity combined with an Allocation of Resources Without Limits or Throttling vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on SRX Series and MX Series with SPC3 allows an unauthenticated network attacker to cause latency in transit packet processing and even packet loss. If transit traffic includes a significant percentage (> 5%) of fragmented packets which need to be reassembled, high latency or packet drops might be observed. This issue affects Juniper Networks Junos OS on SRX Series, MX Series with SPC3: All versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2-S9, 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R1-S1, 19.2R2.
A Stack-based Buffer Overflow vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on MX Series and SRX series allows an unauthenticated networked attacker to cause a flowd crash and thereby a Denial of Service (DoS). Continued receipt of these specific packets will cause a sustained Denial of Service condition. This issue can be triggered by a specific Session Initiation Protocol (SIP) invite packet if the SIP ALG is enabled. Due to this, the PIC will be rebooted and all traffic that traverses the PIC will be dropped. This issue affects: Juniper Networks Junos OS 20.4 versions prior to 20.4R3-S2; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R2; 21.3 versions prior to 21.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1.
An Improper Check for Unusual or Exceptional Conditions vulnerability in the packetIO daemon of Juniper Networks Junos OS Evolved on PTX10003, PTX10004, and PTX10008 allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). Continued receipt of these crafted packets will cause a sustained Denial of Service condition. This issue affects Juniper Networks Junos OS Evolved all versions prior to 20.4R2-S3-EVO on PTX10003, PTX10004, and PTX10008. This issue does not affect: Juniper Networks Junos OS Evolved versions 21.1R1-EVO and above; Juniper Networks Junos OS.
A Missing Release of Resource after Effective Lifetime vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated networked attacker to cause a Denial of Service (DoS) by sending specific packets over VXLAN which cause heap memory to leak and on exhaustion the PFE to reset. The heap memory utilization can be monitored with the command: user@host> show chassis fpc This issue affects: Juniper Networks Junos OS 19.4 versions prior to 19.4R2-S6, 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R2. This issue does not affect versions of Junos OS prior to 19.4R1.
On Juniper Networks Junos OS platforms configured as DHCPv6 local server or DHCPv6 Relay Agent, Juniper Networks Dynamic Host Configuration Protocol Daemon (JDHCPD) process might crash with a core dump if a malformed DHCPv6 packet is received, resulting with the restart of the daemon. This issue only affects DHCPv6, it does not affect DHCPv4. This issue affects: Juniper Networks Junos OS 17.4 versions prior to 17.4R2-S12, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.2X75 versions prior to 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.2 version 19.2R2 and later versions; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2; This issue does not affect Juniper Networks Junos OS prior to 17.4R1.
A vulnerability in the BGP FlowSpec implementation may cause a Juniper Networks Junos OS device to terminate an established BGP session upon receiving a specific BGP FlowSpec advertisement. The BGP NOTIFICATION message that terminates an established BGP session is sent toward the peer device that originally sent the specific BGP FlowSpec advertisement. This specific BGP FlowSpec advertisement received from a BGP peer might get propagated from a Junos OS device running the fixed release to another device that is vulnerable causing BGP session termination downstream. This issue affects IPv4 and IPv6 BGP FlowSpec deployment. This issue affects Juniper Networks Junos OS: 12.3; 12.3X48 on SRX Series; 14.1X53 on EX and QFX Series; 15.1 versions prior to 15.1R7-S5; 15.1F versions prior to 15.1F6-S13; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D497 on NFX Series; 15.1X53 versions prior to 15.1X53-D592 on EX2300/EX3400; 16.1 versions prior to 16.1R7-S7; 17.1 versions prior to 17.1R2-S12, 17.1R3; 17.2 versions prior to 17.2R2-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D102, 17.2X75-D110, 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions prior to 17.4R1-S8, 17.4R2; 18.1 versions prior to 18.1R2-S4, 18.1R3; 18.2X75 versions prior to 18.2X75-D20.
When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of large packets requiring fragmentation, generating the following error messages: [LOG: Err] MQSS(0): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[0:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(0): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1838, QID 0 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk length error in stage 5 - Chunk Address: 0x4321f3 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0x0 [LOG: Notice] Error: /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(0), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D430, 18.2X75-D65 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S1 on MX Series; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S4, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.
On Juniper Networks Junos OS devices, a stream of TCP packets sent to the Routing Engine (RE) may cause mbuf leak which can lead to Flexible PIC Concentrator (FPC) crash or the system to crash and restart (vmcore). This issue can be trigged by IPv4 or IPv6 and it is caused only by TCP packets. This issue is not related to any specific configuration and it affects Junos OS releases starting from 17.4R1. However, this issue does not affect Junos OS releases prior to 18.2R1 when Nonstop active routing (NSR) is configured [edit routing-options nonstop-routing]. The number of mbufs is platform dependent. The following command provides the number of mbufs counter that are currently in use and maximum number of mbufs that can be allocated on a platform: user@host> show system buffers 2437/3143/5580 mbufs in use (current/cache/total) Once the device runs out of mbufs, the FPC crashes or the vmcore occurs and the device might become inaccessible requiring a manual restart. This issue affects Juniper Networks Junos OS 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S5; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D420.12, 18.2X75-D51, 18.2X75-D60, 18.2X75-D34; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Versions of Junos OS prior to 17.4R1 are unaffected by this vulnerability.
A vulnerability in Juniper Networks Junos OS on vMX and MX150 devices may allow an attacker to cause a Denial of Service (DoS) by sending specific packets requiring special processing in microcode that the flow cache can't handle, causing the riot forwarding daemon to crash. By continuously sending the same specific packets, an attacker can repeatedly crash the riot process causing a sustained Denial of Service. Flow cache is specific to vMX based products and the MX150, and is enabled by default in performance mode. This issue can only be triggered by traffic destined to the device. Transit traffic will not cause the riot daemon to crash. When the issue occurs, a core dump and riot log file entry are generated. For example: /var/crash/core.J-UKERN.mpc0.1557255993.3864.gz /home/pfe/RIOT logs: fpc0 riot[1888]: PANIC in lu_reorder_send_packet_postproc(): fpc0 riot[6655]: PANIC in lu_reorder_send_packet_postproc(): This issue affects Juniper Networks Junos OS: 18.1 versions prior to 18.1R3 on vMX and MX150; 18.2 versions prior to 18.2R3 on vMX and MX150; 18.2X75 versions prior to 18.2X75-D60 on vMX and MX150; 18.3 versions prior to 18.3R3 on vMX and MX150; 18.4 versions prior to 18.4R2 on vMX and MX150; 19.1 versions prior to 19.1R2 on vMX and MX150. This issue does not affect Junos OS versions prior to 18.1R1.
When an attacker sends a specific crafted Ethernet Operation, Administration, and Maintenance (Ethernet OAM) packet to a target device, it may improperly handle the incoming malformed data and fail to sanitize this incoming data resulting in an overflow condition. This overflow condition in Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) condition by coring the CFM daemon. Continued receipt of these packets may cause an extended Denial of Service condition. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D95 on SRX Series; 14.1X50 versions prior to 14.1X50-D145; 14.1X53 versions prior to 14.1X53-D47; 15.1 versions prior to 15.1R2; 15.1X49 versions prior to 15.1X49-D170 on SRX Series; 15.1X53 versions prior to 15.1X53-D67.
Certain types of malformed Path Computation Element Protocol (PCEP) packets when received and processed by a Juniper Networks Junos OS device serving as a Path Computation Client (PCC) in a PCEP environment using Juniper's path computational element protocol daemon (pccd) process allows an attacker to cause the pccd process to crash and generate a core file thereby causing a Denial of Service (DoS). Continued receipt of this family of malformed PCEP packets will cause an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 15.1 versions prior to 15.1F6-S13, 15.1R7-S4; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238, 15.1X53-D496, 15.1X53-D592; 16.1 versions prior to 16.1R7-S4; 16.2 versions prior to 16.2R2-S9; 17.1 versions prior to 17.1R2-S11, 17.1R3; 17.2 versions prior to 17.2R1-S9; 17.2 version 17.2R2 and later prior to 17.2R3-S2; 17.3 versions prior to 17.3R3-S3; 17.4 versions prior to 17.4R2-S2, 17.4R3; 18.1 versions prior to 18.1R3-S2; 18.2 versions prior to 18.2R2-S6, 18.2R3; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R2; 18.4 versions prior to 18.4R1-S2, 18.4R2. This issue does not affect releases of Junos OS prior to 15.1R1.
On Juniper Networks products or platforms running Junos OS 12.1X46 prior to 12.1X46-D50, 12.1X47 prior to 12.1X47-D40, 12.3 prior to 12.3R13, 12.3X48 prior to 12.3X48-D30, 13.2X51 prior to 13.2X51-D40, 13.3 prior to 13.3R10, 14.1 prior to 14.1R8, 14.1X53 prior to 14.1X53-D35, 14.1X55 prior to 14.1X55-D35, 14.2 prior to 14.2R5, 15.1 prior to 15.1F6 or 15.1R3, 15.1X49 prior to 15.1X49-D30 or 15.1X49-D40, 15.1X53 prior to 15.1X53-D35, and where RIP is enabled, certain RIP advertisements received by the router may cause the RPD daemon to crash resulting in a denial of service condition.
On Juniper Networks SRX Series Services Gateways chassis clusters running Junos OS 12.1X46 prior to 12.1X46-D65, 12.3X48 prior to 12.3X48-D40, 12.3X48 prior to 12.3X48-D60, flowd daemon on the primary node of an SRX Series chassis cluster may crash and restart when attempting to synchronize a multicast session created via crafted multicast packets.
The Juniper Enhanced jdhcpd daemon may experience high CPU utilization, or crash and restart upon receipt of an invalid IPv6 UDP packet. Both high CPU utilization and repeated crashes of the jdhcpd daemon can result in a denial of service as DHCP service is interrupted. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS 14.1X53 prior to 14.1X53-D12, 14.1X53-D38, 14.1X53-D40 on QFX, EX, QFabric System; 15.1 prior to 15.1F2-S18, 15.1R4 on all products and platforms; 15.1X49 prior to 15.1X49-D80 on SRX; 15.1X53 prior to 15.1X53-D51, 15.1X53-D60 on NFX, QFX, EX.
On Juniper Networks EX Series Ethernet Switches running affected Junos OS versions, a vulnerability in IPv6 processing has been discovered that may allow a specially crafted IPv6 Neighbor Discovery (ND) packet destined to an EX Series Ethernet Switch to cause a slow memory leak. A malicious network-based packet flood of these crafted IPv6 NDP packets may eventually lead to resource exhaustion and a denial of service. The affected Junos OS versions are: 12.3 prior to 12.3R12-S4, 12.3R13; 13.3 prior to 13.3R10; 14.1 prior to 14.1R8-S3, 14.1R9; 14.1X53 prior ro 14.1X53-D12, 14.1X53-D40; 14.1X55 prior to 14.1X55-D35; 14.2 prior to 14.2R6-S4, 14.2R7-S6, 14.2R8; 15.1 prior to 15.1R5; 16.1 before 16.1R3; 16.2 before 16.2R1-S3, 16.2R2. 17.1R1 and all subsequent releases have a resolution for this vulnerability.
A command injection vulnerability in Juniper Networks NorthStar Controller Application prior to version 2.1.0 Service Pack 1 may allow a network-based malicious attacker to cause a denial of service condition.
A denial of service vulnerability in Juniper Networks NorthStar Controller Application prior to version 2.1.0 Service Pack 1 may allow a malicious attacker crafting packets destined to the device to cause a persistent denial of service to the path computation server service.
On Juniper Networks Junos Space versions prior to 16.1R1, an unauthenticated remote attacker with network access to Junos space device can easily create a denial of service condition.
By flooding a Juniper Networks router running Junos OS with specially crafted IPv6 traffic, all available resources can be consumed, leading to the inability to store next hop information for legitimate traffic. In extreme cases, the crafted IPv6 traffic may result in a total resource exhaustion and kernel panic. The issue is triggered by traffic destined to the router. Transit traffic does not trigger the vulnerability. This issue only affects devices with IPv6 enabled and configured. Devices not configured to process IPv6 traffic are unaffected by this vulnerability. This issue was found during internal product security testing. Juniper SIRT is not aware of any malicious exploitation of this vulnerability. Affected releases are Juniper Networks Junos OS 11.4 prior to 11.4R13-S3; 12.3 prior to 12.3R3-S4; 12.3X48 prior to 12.3X48-D30; 13.3 prior to 13.3R10, 13.3R4-S11; 14.1 prior to 14.1R2-S8, 14.1R4-S12, 14.1R8; 14.1X53 prior to 14.1X53-D28, 14.1X53-D40; 14.1X55 prior to 14.1X55-D35; 14.2 prior to 14.2R3-S10, 14.2R4-S7, 14.2R6; 15.1 prior to 15.1F2-S5, 15.1F5-S2, 15.1F6, 15.1R3; 15.1X49 prior to 15.1X49-D40; 15.1X53 prior to 15.1X53-D57, 15.1X53-D70.
A vulnerability in the Routing Protocols Daemon (RPD) with Juniper Extension Toolkit (JET) support can allow a network based unauthenticated attacker to cause a severe memory exhaustion condition on the device. This can have an adverse impact on the system performance and availability. This issue only affects devices with JET support running Junos OS 17.2R1 and subsequent releases. Other versions of Junos OS are unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS: 17.2 versions prior to 17.2R1-S7, 17.2R2-S6, 17.2R3; 17.2X75 versions prior to 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R2-S4, 17.3R3; 17.4 versions prior to 17.4R1-S5, 17.4R2; 18.1 versions prior to 18.1R2-S3, 18.1R3;
The SRX Network Security Daemon (nsd) in Juniper SRX Series services gateways with Junos 12.1X44 before 12.1X44-D50, 12.1X46 before 12.1X46-D35, 12.1X47 before 12.1X47-D25, and 12.3X48 before 12.3X48-D15 allows remote DNS servers to cause a denial of service (crash) via a crafted DNS response.
An uncontrolled resource consumption vulnerability in Juniper Networks Junos OS on QFX5000 Series and EX4600 Series switches allows an attacker sending large amounts of legitimate traffic destined to the device to cause Interchassis Control Protocol (ICCP) interruptions, leading to an unstable control connection between the Multi-Chassis Link Aggregation Group (MC-LAG) nodes which can in turn lead to traffic loss. Continued receipt of this amount of traffic will create a sustained Denial of Service (DoS) condition. An indication that the system could be impacted by this issue is the following log message: "DDOS_PROTOCOL_VIOLATION_SET: Warning: Host-bound traffic for protocol/exception LOCALNH:aggregate exceeded its allowed bandwidth at fpc <fpc number> for <n> times, started at <timestamp>" This issue affects Juniper Networks Junos OS on QFX5000 Series and EX4600 Series: 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S7; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R1-S1, 20.4R2.
Due to an Improper Initialization vulnerability in Juniper Networks Junos OS on PTX platforms and QFX10K Series with Paradise (PE) chipset-based line cards, ddos-protection configuration changes made from the CLI will not take effect as expected beyond the default DDoS (Distributed Denial of Service) settings in the Packet Forwarding Engine (PFE). This may cause BFD sessions to flap when a high rate of specific packets are received. Flapping of BFD sessions in turn may impact routing protocols and network stability, leading to a Denial of Service (DoS) condition. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects only the following platforms with Paradise (PE) chipset-based line cards: PTX1000, PTX3000 (NextGen), PTX5000, PTX10008, PTX10016 Series and QFX10002 Series. This issue affects: Juniper Networks Junos OS 17.4 versions prior to 17.4R3-S5 on PTX Series, QFX10K Series; 18.2 versions prior to 18.2R3-S8 on PTX Series, QFX10K Series; 18.3 versions prior to 18.3R3-S5 on PTX Series, QFX10K Series; 18.4 versions prior to 18.4R2-S8 on PTX Series, QFX10K Series; 19.1 versions prior to 19.1R3-S5 on PTX Series, QFX10K Series; 19.2 versions prior to 19.2R3-S2 on PTX Series, QFX10K Series; 19.3 versions prior to 19.3R3-S2 on PTX Series, QFX10K Series; 19.4 versions prior to 19.4R3-S2 on PTX Series, QFX10K Series; 20.1 versions prior to 20.1R3 on PTX Series, QFX10K Series; 20.2 versions prior to 20.2R2-S3, 20.2R3 on PTX Series, QFX10K Series; 20.3 versions prior to 20.3R2 on PTX Series, QFX10K Series; 20.4 versions prior to 20.4R2 on PTX Series, QFX10K Series.
On Juniper Networks Junos OS Evolved devices, receipt of a specific IPv6 packet may cause an established IPv6 BGP session to terminate, creating a Denial of Service (DoS) condition. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue does not affect IPv4 BGP sessions. This issue affects IBGP or EBGP peer sessions with IPv6. This issue affects: Juniper Networks Junos OS Evolved: 19.4 versions prior to 19.4R2-S3-EVO; 20.1 versions prior to 20.1R2-S3-EVO; 20.2 versions prior to 20.2R2-S1-EVO; 20.3 versions prior to 20.3R2-EVO. This issue does not affect Juniper Networks Junos OS releases.
An uncontrolled resource consumption vulnerability in Message Queue Telemetry Transport (MQTT) server of Juniper Networks Junos OS allows an attacker to cause MQTT server to crash and restart leading to a Denial of Service (DoS) by sending a stream of specific packets. A Juniper Extension Toolkit (JET) application designed with a listening port uses the Message Queue Telemetry Transport (MQTT) protocol to connect to a mosquitto broker that is running on Junos OS to subscribe for events. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: 16.1R1 and later versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 16.1R1.
A vulnerability in Juniper Networks Junos OS ACX500 Series, ACX4000 Series, may allow an attacker to cause a Denial of Service (DoS) by sending a high rate of specific packets to the device, resulting in a Forwarding Engine Board (FFEB) crash. Continued receipt of these packets will sustain the Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on ACX500 Series, ACX4000 Series: 17.4 versions prior to 17.4R3-S2.
A NULL Pointer Dereference vulnerability in the Captive Portal Content Delivery (CPCD) services daemon (cpcd) of Juniper Networks Junos OS on MX Series with MS-PIC, MS-SPC3, MS-MIC or MS-MPC allows an attacker to send malformed HTTP packets to the device thereby causing a Denial of Service (DoS), crashing the Multiservices PIC Management Daemon (mspmand) process thereby denying users the ability to login, while concurrently impacting other mspmand services and traffic through the device. Continued receipt and processing of these malformed packets will create a sustained Denial of Service (DoS) condition. While the Services PIC is restarting, all PIC services will be bypassed until the Services PIC completes its boot process. An attacker sending these malformed HTTP packets to the device who is not part of the Captive Portal experience is not able to exploit this issue. This issue is not applicable to MX RE-based CPCD platforms. This issue affects: Juniper Networks Junos OS on MX Series 17.3 version 17.3R1 and later versions prior to 17.4 versions 17.4R2-S9, 17.4R3-S2; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R3-S1; 18.4 versions prior to 18.4R3; 19.1 versions prior to 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3. This issue does not affect: Juniper Networks Junos OS versions prior to 17.3R1.
On Juniper Networks SRX Series devices with link aggregation (lag) configured, executing any operation that fetches Aggregated Ethernet (AE) interface statistics, including but not limited to SNMP GET requests, causes a slow kernel memory leak. If all the available memory is consumed, the traffic will be impacted and a reboot might be required. The following log can be seen if this issue happens. /kernel: rt_pfe_veto: Memory over consumed. Op 1 err 12, rtsm_id 0:-1, msg type 72 /kernel: rt_pfe_veto: free kmem_map memory = (20770816) curproc = kmd An administrator can use the following CLI command to monitor the status of memory consumption (ifstat bucket): user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 2588977 162708K - 19633958 <<<< user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 3021629 189749K - 22914415 <<<< This issue affects Juniper Networks Junos OS on SRX Series: 17.1 versions 17.1R3 and above prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S5; 18.2 versions prior to 18.2R3-S7, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS prior to 17.1R3.
A vulnerability in telnetd service on Junos OS allows a remote attacker to cause a limited memory and/or CPU consumption denial of service attack. This issue was found during internal product security testing. Affected releases are Juniper Networks Junos OS 12.1X46 prior to 12.1X46-D45; 12.3X48 prior to 12.3X48-D30; 14.1 prior to 14.1R4-S9, 14.1R8; 14.2 prior to 14.2R6; 15.1 prior to 15.1F5, 15.1R3; 15.1X49 prior to 15.1X49-D40; 15.1X53 prior to 15.1X53-D232, 15.1X53-D47.
Juniper Junos 10.0 before 10.0S28, 10.4 before 10.4R7, 11.1 before 11.1R5, 11.2 before 11.2R2, and 11.4 before 11.4R1, when in a Next-Generation Multicast VPN (NGEN MVPN) environment, allows remote attackers to cause a denial of service (RPD routing daemon crash) via a large number of crafted PIM (S,G) join requests.
Juniper Junos before 10.4S14, 11.4 before 11.4R5-S2, 12.1R before 12.1R3, 12.1X44 before 12.1X44-D20, and 12.1X45 before 12.1X45-D15 on SRX Series services gateways, when a plugin using TCP proxy is configured, allows remote attackers to cause a denial of service (flow daemon crash) via an unspecified sequence of TCP packets.
Junos Pulse Secure Access Service (IVE) 7.1 before 7.1r5, 7.2 before 7.2r10, 7.3 before 7.3r6, and 7.4 before 7.4r3 and Junos Pulse Access Control Service (UAC) 4.1 before 4.1r8.1, 4.2 before 4.2r5, 4.3 before 4.3r6 and 4.4 before 4.4r3, when a hardware SSL acceleration card is enabled, allows remote attackers to cause a denial of service (device hang) via a crafted packet.
On Junos OS devices with SNMP enabled, a network based attacker with unfiltered access to the RE can cause the Junos OS snmpd daemon to crash and restart by sending a crafted SNMP packet. Repeated crashes of the snmpd daemon can result in a partial denial of service condition. Additionally, it may be possible to craft a malicious SNMP packet in a way that can result in remote code execution. SNMP is disabled in Junos OS by default. Junos OS devices with SNMP disabled are not affected by this issue. No other Juniper Networks products or platforms are affected by this issue. NOTE: This is a different issue than Cisco CVE-2017-6736, CVE-2017-6737, and CVE-2017-6738. Affected releases are Juniper Networks Junos OS 12.1X46 prior to 12.1X46-D67; 12.3X48 prior to 12.3X48-D51, 12.3X48-D55; 13.3 prior to 13.3R10-S2; 14.1 prior to 14.1R2-S10, 14.1R8-S4, 14.1R9; 14.1X50 prior to 14.1X50-D185; 14.1X53 prior to 14.1X53-D122, 14.1X53-D44, 14.1X53-D50; 14.2 prior to 14.2R4-S9, 14.2R7-S7, 14.2R8; 15.1 prior to 15.1F2-S18, 15.1F6-S7, 15.1R4-S8, 15.1R5-S5, 15.1R6-S1, 15.1R7; 15.1X49 prior to 15.1X49-D100, 15.1X49-D110; 15.1X53 prior to 15.1X53-D231, 15.1X53-D47, 15.1X53-D48, 15.1X53-D57, 15.1X53-D64, 15.1X53-D70; 16.1 prior to 16.1R3-S4, 16.1R4-S3, 16.1R4-S4, 16.1R5; 16.2 prior to 16.2R2, 16.2R3; 17.1 prior to 17.1R1-S3, 17.1R2, 17.1R3; 17.2 prior to 17.2R1-S1, 17.2R2; 17.2X75 prior to 17.2X75-D30. Junos releases prior to 10.2 are not affected.
When SAML authentication is enabled, Juniper Networks Mist Cloud UI might incorrectly handle child elements in SAML responses, allowing a remote attacker to modify a valid SAML response without invalidating its cryptographic signature to bypass SAML authentication security controls. This issue affects all Juniper Networks Mist Cloud UI versions prior to September 2 2020.
An Improper Input Validation vulnerability in the 802.1X Authentication (dot1x) Daemon of Juniper Networks Junos OS allows a local, low-privileged attacker with access to the CLI to cause a Denial of Service (DoS). On running a specific operational dot1x command, the dot1x daemon crashes. An attacker can cause a sustained DoS condition by running this command repeatedly. When the crash occurs, the authentication status of any 802.1x clients is cleared, and any authorized dot1x port becomes unauthorized. The client cannot re-authenticate until the dot1x daemon restarts. This issue affects Junos OS: * All versions before 20.4R3-S10; * 21.2 versions before 21.2R3-S7; * 21.4 versions before 21.4R3-S6; * 22.1 versions before 22.1R3-S5; * 22.2 versions before 22.2R3-S3; * 22.3 versions before 22.3R3-S2; * 22.4 versions before 22.4R3-S1; * 23.2 versions before 23.2R2.
An Improper Input Validation vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS Evolved allows a local, low-privileged attacker to cause a Denial of Service (DoS). When a specific "clear" command is run, the Advanced Forwarding Toolkit manager (evo-aftmand-bt or evo-aftmand-zx) crashes and restarts. The crash impacts all traffic going through the FPCs, causing a DoS. Running the command repeatedly leads to a sustained DoS condition. This issue affects Junos OS Evolved: * All versions before 20.4R3-S9-EVO, * from 21.2-EVO before 21.2R3-S7-EVO, * from 21.3-EVO before 21.3R3-S5-EVO, * from 21.4-EVO before 21.4R3-S6-EVO, * from 22.1-EVO before 22.1R3-S4-EVO, * from 22.2-EVO before 22.2R3-S3-EVO, * from 22.3-EVO before 22.3R3-S3-EVO, * from 22.4-EVO before 22.4R3-EVO, * from 23.2-EVO before 23.2R2-EVO.
An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When certain specific crafted BGP UPDATE messages are received over an established BGP session, one BGP session may be torn down with an UPDATE message error, or the issue may propagate beyond the local system which will remain non-impacted, but may affect one or more remote systems. This issue is exploitable remotely as the crafted UPDATE message can propagate through unaffected systems and intermediate BGP speakers. Continuous receipt of the crafted BGP UPDATE messages will create a sustained Denial of Service (DoS) condition for impacted devices. This issue affects eBGP and iBGP, in both IPv4 and IPv6 implementations. This issue requires a remote attacker to have at least one established BGP session. Improper Input Validation, Denial of Service vulnerability in Juniper Networks, Inc. Junos OS (BGP, rpd modules), Juniper Networks, Inc. Junos OS Evolved (BGP, rpd modules) allows Fuzzing.This issue affects Junos OS: * All versions before 20.4R3-S10, * from 21.1R1 through 21.*, * from 21.2 before 21.2R3-S5, * from 21.3 before 21.3R3-S5, * from 21.4 before 21.4R3-S7 (unaffected from 21.4R3-S5, affected from 21.4R3-S6) * from 22.1 before 22.1R3-S4, * from 22.2 before 22.2R3-S3, * from 22.3 before 22.3R3-S1, * from 22.4 before 22.4R3, * from 23.2 before 23.2R2. Junos OS Evolved: * All versions before 20.4R3-S10-EVO, * from 21.2-EVO before 21.2R3-S7-EVO, * from 21.3-EVO before 21.3R3-S5-EVO, * from 21.4-EVO before 21.4R3-S5-EVO, * from 22.1-EVO before 22.1R3-S4-EVO, * from 22.2-EVO before 22.2R3-S3-EVO, * from 22.3-EVO before 22.3R3-S1-EVO, * from 22.4-EVO before 22.4R3-EVO, * from 23.2-EVO before 23.2R2-EVO.