Specific IPv6 DHCP packets received by the jdhcpd daemon will cause a memory resource consumption issue to occur on a Junos OS device using the jdhcpd daemon configured to respond to IPv6 requests. Once started, memory consumption will eventually impact any IPv4 or IPv6 request serviced by the jdhcpd daemon, thus creating a Denial of Service (DoS) condition to clients requesting and not receiving IP addresses. Additionally, some clients which were previously holding IPv6 addresses will not have their IPv6 Identity Association (IA) address and network tables agreed upon by the jdhcpd daemon after the failover event occurs, which leads to more than one interface, and multiple IP addresses, being denied on the client. Affected releases are Juniper Networks Junos OS: 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R2.

An Insufficient Algorithmic Complexity combined with an Allocation of Resources Without Limits or Throttling vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on SRX Series and MX Series with SPC3 allows an unauthenticated network attacker to cause latency in transit packet processing and even packet loss. If transit traffic includes a significant percentage (> 5%) of fragmented packets which need to be reassembled, high latency or packet drops might be observed. This issue affects Juniper Networks Junos OS on SRX Series, MX Series with SPC3: All versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2-S9, 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R1-S1, 19.2R2.

A vulnerability in the HTTP/HTTPS service used by J-Web, Web Authentication, Dynamic-VPN (DVPN), Firewall Authentication Pass-Through with Web-Redirect, and Captive Portal allows an unauthenticated attacker to cause an extended Denial of Service (DoS) for these services by sending a high number of specific requests. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S17 on EX Series; 12.3X48 versions prior to 12.3X48-D105 on SRX Series; 15.1 versions prior to 15.1R7-S8; 15.1X49 versions prior to 15.1X49-D230 on SRX Series; 16.1 versions prior to 16.1R7-S8; 17.4 versions prior to 17.4R2-S12, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2; 20.2 versions prior to 20.2R1-S1, 20.2R2.

An uncontrolled resource consumption vulnerability in Juniper Networks Junos OS on QFX5000 Series and EX4600 Series switches allows an attacker sending large amounts of legitimate traffic destined to the device to cause Interchassis Control Protocol (ICCP) interruptions, leading to an unstable control connection between the Multi-Chassis Link Aggregation Group (MC-LAG) nodes which can in turn lead to traffic loss. Continued receipt of this amount of traffic will create a sustained Denial of Service (DoS) condition. An indication that the system could be impacted by this issue is the following log message: "DDOS_PROTOCOL_VIOLATION_SET: Warning: Host-bound traffic for protocol/exception LOCALNH:aggregate exceeded its allowed bandwidth at fpc <fpc number> for <n> times, started at <timestamp>" This issue affects Juniper Networks Junos OS on QFX5000 Series and EX4600 Series: 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S7; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R1-S1, 20.4R2.

IPv6 sendd in Juniper Junos 12.1X44 before 12.1X44-D51, 12.1X46 before 12.1X46-D36, 12.1X46 before 12.1X46-D40, 12.1X47 before 12.1X47-D25, 12.3 before 12.3R10, 12.3X48 before 12.3X48-D20, 13.2 before 13.2R8, 13.3 before 13.3R6, 14.1 before 14.1R5, 14.2 before 14.2R3, 15.1 before 15.1R1, and 15.1X49 before 15.1X49-D20, when the "set protocols neighbor-discovery secure security-level default" option is configured, allows remote attackers to cause a denial of service (CPU consumption) via a crafted Secure Neighbor Discovery (SEND) Protocol packet.

The SRX Network Security Daemon (nsd) in Juniper SRX Series services gateways with Junos 12.1X44 before 12.1X44-D50, 12.1X46 before 12.1X46-D35, 12.1X47 before 12.1X47-D25, and 12.3X48 before 12.3X48-D15 allows remote DNS servers to cause a denial of service (crash) via a crafted DNS response.

The Juniper EX4600, QFX3500, QFX3600, and QFX5100 switches with Junos 13.2X51-D15 through 13.2X51-D25, 13.2X51 before 13.2X51-D30, and 14.1X53 before 14.1X53-D10 allows remote attackers to cause a denial of service (CPU consumption) via unspecified vectors.

A NULL Pointer Dereference vulnerability in Juniper Networks Junos OS allows an attacker to send a specific packet causing the packet forwarding engine (PFE) to crash and restart, resulting in a Denial of Service (DoS). By continuously sending these specific packets, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue only affects Juniper Networks NFX Series, SRX Series platforms when SSL Proxy is configured. This issue affects Juniper Networks Junos OS on NFX Series and SRX Series: 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S1; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S2, 19.2R2; 19.3 versions prior to 19.3R2. This issue does not affect Juniper Networks Junos OS versions on NFX Series and SRX Series prior to 18.3R1.

A vulnerability in Juniper Networks Junos OS, which only affects the release 18.4R2-S5, where a function is inconsistently implemented on Juniper Networks Junos QFX5000 Series and EX4600 Series, and if "storm-control enhanced" is configured, can lead to the enhanced storm control filter group not be installed. It will cause storm control not to work hence allowing an attacker to cause high CPU usage or packet loss issues by sending a large amount of broadcast or unknown unicast packets arriving the device. This issue affects Juniper Networks QFX5100, QFX5110, QFX5120, QFX5200, QFX5210, EX4600, and EX4650, and QFX5100 with QFX 5e Series image installed. QFX5130 and QFX5220 are not affected from this issue. This issue affects Juniper Networks Junos OS 18.4R2-S5 on QFX5000 Series and EX4600 Series. No other product or platform is affected by this vulnerability.

Embedthis Appweb before 4.6.6 and 5.x before 5.2.1 allows remote attackers to cause a denial of service (NULL pointer dereference) via a Range header with an empty value, as demonstrated by "Range: x=,".

Juniper Junos OS before 12.1X44-D50, 12.1X46 before 12.1X46-D35, 12.1X47 before 12.1X47-D25, 12.3 before 12.3R10, 12.3X48 before 12.3X48-D15, 13.2 before 13.2R8, 13.3 before 13.3R7, 14.1 before 14.1R5, and 14.2 before 14.2R1 do not properly handle TCP packet reassembly, which allows remote attackers to cause a denial of service (buffer consumption) via a crafted sequence of packets "destined to the device."

The srxpfe process may crash on SRX Series services gateways when the UTM module processes a specific fragmented HTTP packet. The packet is misinterpreted as a regular TCP packet which causes the processor to crash. This issue affects all SRX Series platforms that support URL-Filtering and have web-filtering enabled. Affected releases are Juniper Networks Junos OS: 12.3X48 versions prior to 12.3X48-D85 on SRX Series; 15.1X49 versions prior to 15.1X49-D181, 15.1X49-D190 on SRX Series; 17.3 versions on SRX Series; 17.4 versions prior to 17.4R1-S8, 17.4R2-S5, 17.4R3 on SRX Series; 18.1 versions prior to 18.1R3-S6 on SRX Series; 18.2 versions prior to 18.2R2-S1, 18.2R3 on SRX Series; 18.3 versions prior to 18.3R1-S2, 18.3R2 on SRX Series; 18.4 versions prior to 18.4R1-S1, 18.4R2 on SRX Series.

Juniper Junos before 11.4R11, 12.1 before 12.1R9, 12.2 before 12.2R7, 12.3R4 before 12.3R4-S3, 13.1 before 13.1R4, 13.2 before 13.2R2, and 13.3 before 13.3R1, as used in MX Series and T4000 routers, allows remote attackers to cause a denial of service (PFE restart) via a crafted IP packet to certain (1) Trio or (2) Cassis-based Packet Forwarding Engine (PFE) modules.

Unspecified vulnerability in Juniper Junos before 11.4R10-S1, before 11.4R11, 12.1X44 before 12.1X44-D26, 12.1X44 before 12.1X44-D30, 12.1X45 before 12.1X45-D20, and 12.1X46 before 12.1X46-D10, when Dynamic IPsec VPN is configured, allows remote attackers to cause a denial of service (new Dynamic VPN connection failures and CPU and disk consumption) via unknown vectors.

When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of large packets requiring fragmentation, generating the following error messages: [LOG: Err] MQSS(0): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[0:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(0): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1838, QID 0 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk length error in stage 5 - Chunk Address: 0x4321f3 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0x0 [LOG: Notice] Error: /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(0), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D430, 18.2X75-D65 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S1 on MX Series; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S4, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.

On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific BGP packet can lead to a routing process daemon (RPD) crash and restart. This issue can occur even before the BGP session with the peer is established. Repeated receipt of this specific BGP packet can result in an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 18.2X75 versions starting from 18.2X75-D50.8, 18.2X75-D60 and later versions, prior to 18.2X75-D52.8, 18.2X75-D53, 18.2X75-D60.2, 18.2X75-D65.1, 18.2X75-D70; 19.4 versions 19.4R1 and 19.4R1-S1; 20.1 versions prior to 20.1R1-S2, 20.1R2. Juniper Networks Junos OS Evolved: 19.4-EVO versions prior to 19.4R2-S2-EVO; 20.1-EVO versions prior to 20.1R2-EVO. This issue does not affect: Juniper Networks Junos OS releases prior to 19.4R1. Juniper Networks Junos OS Evolved releases prior to 19.4R1-EVO.

When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of small fragments requiring reassembly, generating the following error messages: [LOG: Err] MQSS(2): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[2:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(2): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1960, QID 0 [LOG: Err] MQSS(2): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0xc38fb1 [LOG: Notice] Error: /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(2), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S9, 17.4R3-S1 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D34, 18.2X75-D41, 18.2X75-D53, 18.2X75-D65, 18.2X75-D430 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S2 on MX Series; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.

Juniper JUNOS 5.x through JUNOS 7.x allows remote attackers to cause a denial of service (routing disabled) via a large number of MPLS packets, which are not filtered or verified before being sent to the Routing Engine, which reduces the speed at which other packets are processed.

On QFX and PTX Series, receipt of a malformed packet for J-Flow sampling might crash the FPC (Flexible PIC Concentrator) process which causes all interfaces to go down. By continuously sending the offending packet, an attacker can repeatedly crash the FPC process causing a sustained Denial of Service (DoS). This issue affects both IPv4 and IPv6 packet processing. Affected releases are Juniper Networks Junos OS on QFX and PTX Series: 17.4 versions prior to 17.4R2-S1, 17.4R3; 18.1 versions prior to 18.1R3-S1; 18.2 versions prior to 18.2R1-S3, 18.2R2; 17.2X75 versions prior to 17.2X75-D91, 17.2X75-D100.

A memory leak vulnerability in the of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the device by sending specific commands from a peered BGP host and having those BGP states delivered to the vulnerable device. This issue affects: Juniper Networks Junos OS: 18.1 versions prior to 18.1R2-S4, 18.1R3-S1; 18.1X75 all versions. Versions before 18.1R1 are not affected.

The routing protocol daemon (RPD) process will crash and restart when a specific invalid IPv4 PIM Join packet is received. While RPD restarts after a crash, repeated crashes can result in an extended Denial of Service (DoS) condition. This issue only affects IPv4 PIM. IPv6 PIM is unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77; 12.3X48 versions prior to 12.3X48-D77; 15.1 versions prior to 15.1F6-S10, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D150; 15.1X53 versions prior to 15.1X53-D233, 15.1X53-D59; 16.1 versions prior to 16.1R3-S8, 16.1R4-S8, 16.1R7; 16.2 versions prior to 16.2R2-S6; 17.1 versions prior to 17.1R2-S6, 17.1R3; 17.2 versions prior to 17.2R2-S3, 17.2R3; 17.3 versions prior to 17.3R2-S4, 17.3R3; 17.4 versions prior to 17.4R2.

This issue only affects devices with three (3) or more MPC10's installed in a single chassis with OSPF enabled and configured on the device. An Insufficient Resource Pool weakness allows an attacker to cause the device's Open Shortest Path First (OSPF) states to transition to Down, resulting in a Denial of Service (DoS) attack. This attack requires a relatively large number of specific Internet Mixed (IMIXed) types of genuine and valid IPv6 packets to be transferred by the attacker in a relatively short period of time, across three or more PFE's on the device at the same time. Continued receipt of the traffic sent by the attacker will continue to cause OSPF to remain in the Down starting state, or flap between other states and then again to Down, causing a persistent Denial of Service. This attack will affect all IPv4, and IPv6 traffic served by the OSPF routes once the OSPF states transition to Down. This issue affects: Juniper Networks Junos OS on MX480, MX960, MX2008, MX2010, MX2020: 18.1 versions prior to 18.1R2-S4, 18.1R3-S5; 18.1X75 version 18.1X75-D10 and later versions; 18.2 versions prior to 18.2R1-S5, 18.2R2-S3, 18.2R3; 18.2X75 versions prior to 18.2X75-D50; 18.3 versions prior to 18.3R1-S4, 18.3R2, 18.3R3; 18.4 versions prior to 18.4R1-S2, 18.4R2.

On EX4300-MP Series devices with any lo0 filters applied, transit network traffic may reach the control plane via loopback interface (lo0). The device may fail to forward such traffic. This issue affects Juniper Networks Junos OS 18.2 versions prior to 18.2R1-S2, 18.2R2 on EX4300-MP Series. This issue does not affect any other EX series devices.

Receipt of a specific packet on the out-of-band management interface fxp0 may cause the system to crash and restart (vmcore). By continuously sending a specially crafted packet to the fxp0 interface, an attacker can repetitively crash the rpd process causing prolonged Denial of Service (DoS). Affected releases are Juniper Networks SRX5000 Series: 12.1X46 versions prior to 12.1X46-D82; 12.3X48 versions prior to 12.3X48-D80; 15.1X49 versions prior to 15.1X49-D160.

A vulnerability in the SIP ALG packet processing service of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the device by sending specific types of valid SIP traffic to the device. In this case, the flowd process crashes and generates a core dump while processing SIP ALG traffic. Continued receipt of these valid SIP packets will result in a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 12.3X48 versions prior to 12.3X48-D61, 12.3X48-D65 on SRX Series; 15.1X49 versions prior to 15.1X49-D130 on SRX Series; 17.3 versions prior to 17.3R3 on SRX Series; 17.4 versions prior to 17.4R2 on SRX Series.

In MPLS environments, receipt of a specific SNMP packet may cause the routing protocol daemon (RPD) process to crash and restart. By continuously sending a specially crafted SNMP packet, an attacker can repetitively crash the RPD process causing prolonged denial of service. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS : 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D75 on SRX Series; 14.1X53 versions prior to 14.1X53-D48 on EX/QFX series; 15.1 versions prior to 15.1R4-S9, 15.1R7-S2; 15.1F6 versions prior to 15.1F6-S11; 15.1X49 versions prior to 15.1X49-D141, 15.1X49-D144, 15.1X49-D150 on SRX Series; 15.1X53 versions prior to 15.1X53-D234 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D68 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX Series; 15.1X53 versions prior to 15.1X53-D590 on EX2300/EX3400 Series; 15.1X54 on ACX Series; 16.1 versions prior to 16.1R3-S10, 16.1R4-S11, 16.1R6-S5, 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R2-S6; 17.1 versions prior to 17.1R2-S8, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D92, 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R3; 17.4 versions prior to 17.4R1-S4, 17.4R2; 18.1 versions prior to 18.1R1-S1, 18.1R2-S1, 18.1R3; 18.2X75 versions prior to 18.2X75-D10.

On Junos devices with the BGP graceful restart helper mode enabled or the BGP graceful restart mechanism enabled, a certain sequence of BGP session restart on a remote peer that has the graceful restart mechanism enabled may cause the local routing protocol daemon (RPD) process to crash and restart. Repeated crashes of the RPD process can cause prolonged Denial of Service (DoS). Graceful restart helper mode for BGP is enabled by default. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S3; 16.2 versions prior to 16.2R2-S9; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3; 17.2X75 versions prior to 17.2X75-D105; 17.3 versions prior to 17.3R3-S2; 17.4 versions prior to 17.4R1-S7, 17.4R2-S2, 17.4R3; 18.1 versions prior to 18.1R3-S2; 18.2 versions prior to 18.2R2; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D30; 18.3 versions prior to 18.3R1-S4, 18.3R2. Junos OS releases prior to 16.1R1 are not affected.

A vulnerability in the srxpfe process on Protocol Independent Multicast (PIM) enabled SRX series devices may lead to crash of the srxpfe process and an FPC reboot while processing (PIM) messages. Sustained receipt of these packets may lead to an extended denial of service condition. Affected releases are Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D80; 15.1X49 versions prior to 15.1X49-D160; 17.3 versions prior to 17.3R3-S7 17.4 versions prior to 17.4R2-S8, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R2; 18.3 versions prior to 18.3R2.

The SRX flowd process, responsible for packet forwarding, may crash and restart when processing specific multicast packets. By continuously sending the specific multicast packets, an attacker can repeatedly crash the flowd process causing a sustained Denial of Service. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D90; 15.1X49 versions prior to 15.1X49-D180; 17.3 versions; 17.4 versions prior to 17.4R2-S5, 17.4R3; 18.1 versions prior to 18.1R3-S6; 18.2 versions prior to 18.2R2-S4, 18.2R3; 18.3 versions prior to 18.3R2-S1, 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S1, 19.1R2.

When BGP tracing is enabled an incoming BGP message may cause the Junos OS routing protocol daemon (rpd) process to crash and restart. While rpd restarts after a crash, repeated crashes can result in an extended DoS condition. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S4, 16.1R7-S5; 16.2 versions prior to 16.2R2-S9, 16.2R3; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3-S1; 17.3 versions prior to 17.3R3-S3, 17.3R3-S4, 17.3R4; 17.4 versions prior to 17.4R1-S7, 17.4R2-S3, 17.4R2-S4, 17.4R3; 18.1 versions prior to 18.1R2-S4, 18.1R3-S4, 18.1R4; 18.2 versions prior to 18.2R2-S2, 18.2R2-S3, 18.2R3; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R1-S3, 18.3R2; 18.4 versions prior to 18.4R1-S2, 18.4R2. This issue does not affect Junos releases prior to 16.1R1.

SSL-Proxy feature on SRX devices fails to handle a hardware resource limitation which can be exploited by remote SSL/TLS servers to crash the flowd daemon. Repeated crashes of the flowd daemon can result in an extended denial of service condition. For this issue to occur, clients protected by the SRX device must initiate a connection to the malicious server. This issue affects: Juniper Networks Junos OS on SRX5000 Series: 12.3X48 versions prior to 12.3X48-D85; 15.1X49 versions prior to 15.1X49-D180; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R2-S6, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R2; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R2.

When a specific BGP flowspec configuration is enabled and upon receipt of a specific matching BGP packet meeting a specific term in the flowspec configuration, a reachable assertion failure occurs, causing the routing protocol daemon (rpd) process to crash with a core file being generated. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D70 on SRX Series; 14.1X53 versions prior to 14.1X53-D47 on EX2200/VC, EX3200, EX3300/VC, EX4200, EX4300, EX4550/VC, EX4600, EX6200, EX8200/VC (XRE), QFX3500, QFX3600, QFX5100; 15.1 versions prior to 15.1R3; 15.1F versions prior to 15.1F3; 15.1X49 versions prior to 15.1X49-D140 on SRX Series; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400.

The flowd process, responsible for forwarding traffic in SRX Series services gateways, may crash and restart when processing specific transit IP packets through an IPSec tunnel. Continued processing of these packets may result in an extended Denial of Service (DoS) condition. This issue only occurs when IPSec tunnels are configured. Systems without IPSec tunnel configurations are not vulnerable to this issue. This issue affects Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D171, 15.1X49-D180 on SRX Series; 18.2 versions 18.2R2-S1 and later, prior to 18.2R3 on SRX Series; 18.4 versions prior to 18.4R2 on SRX Series.

In a Dynamic Host Configuration Protocol version 6 (DHCPv6) environment, the jdhcpd daemon may crash and restart upon receipt of certain DHCPv6 solicit messages received from a DHCPv6 client. By continuously sending the same crafted packet, an attacker can repeatedly crash the jdhcpd process causing a sustained Denial of Service (DoS) to both IPv4 and IPv6 clients. Affected releases are Juniper Networks Junos OS: 15.1 versions prior to 15.1F6-S12, 15.1R7-S3; 15.1X49 versions prior to 15.1X49-D171, 15.1X49-D180; 15.1X53 versions prior to 15.1X53-D236, 15.1X53-D496; 16.1 versions prior to 16.1R3-S10, 16.1R7-S4; 16.2 versions prior to 16.2R2-S8; 17.1 versions prior to 17.1R2-S10, 17.1R3; 17.2 versions prior to 17.2R1-S8, 17.2R3-S1; 17.3 versions prior to 17.3R3-S3; 17.4 versions prior to 17.4R1-S6, 17.4R2-S3; 18.1 versions prior to 18.1R2-S4, 18.1R3-S2; 18.2 versions prior to 18.2R2; 18.2X75 versions prior to 18.2X75-D30; 18.3 versions prior to 18.3R1-S2. This issue does not affect Junos OS releases prior to 15.1.

A firewall bypass vulnerability in the proxy ARP service of Juniper Networks Junos OS allows an attacker to cause a high CPU condition leading to a Denial of Service (DoS). This issue affects only IPv4. Affected releases are Juniper Networks Junos OS: 12.1X46 versions above and including 12.1X46-D25 prior to 12.1X46-D71, 12.1X46-D73 on SRX Series; 12.3X48 versions prior to 12.3X48-D50 on SRX Series; 15.1X49 versions prior to 15.1X49-D75 on SRX Series.

An unexpected status return value weakness in the Next-Generation Multicast VPN (NG-mVPN) service of Juniper Networks Junos OS allows attacker to cause a Denial of Service (DoS) condition and core the routing protocol daemon (rpd) process when a specific malformed IPv4 packet is received by the device running BGP. This malformed packet can be crafted and sent to a victim device including when forwarded directly through a device receiving such a malformed packet, but not if the malformed packet is first de-encapsulated from an encapsulated format by a receiving device. Continued receipt of the malformed packet will result in a sustained Denial of Service condition. This issue affects: Juniper Networks Junos OS 15.1 versions prior to 15.1F6-S12, 15.1R7-S2; 15.1X49 versions prior to 15.1X49-D150 on SRX Series; 15.1X53 versions prior to 15.1X53-D68, 15.1X53-D235, 15.1X53-D495, 15.1X53-D590; 16.1 versions prior to 16.1R3-S10, 16.1R4-S12, 16.1R6-S6, 16.1R7-S2; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S9, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R2-S6, 17.2R3; 17.3 versions prior to 17.3R2-S4, 17.3R3.

A Denial of Service (DoS) vulnerability in BGP in Juniper Networks Junos OS configured as a VPLS PE allows an attacker to craft a specific BGP message to cause the routing protocol daemon (rpd) process to crash and restart. While rpd restarts after a crash, repeated crashes can result in an extended DoS condition. This issue only affects PE routers configured with BGP Auto discovery for LDP VPLS. Other BGP configurations are unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D81; 12.3 versions prior to 12.3R12-S12; 12.3X48 versions prior to 12.3X48-D76; 14.1X53 versions prior to 14.1X53-D48; 15.1 versions prior to 15.1F6-S12, 15.1R7-S2; 15.1X49 versions prior to 15.1X49-D150; 15.1X53 versions prior to 15.1X53-D235, 15.1X53-D495, 15.1X53-D590, 15.1X53-D68; 16.1 versions prior to 16.1R3-S10, 16.1R4-S12, 16.1R6-S6, 16.1R7-S1; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S9, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R2-S6, 17.2R3; 17.3 versions prior to 17.3R2-S4, 17.3R3; 17.4 versions prior to 17.4R1-S5, 17.4R2; 18.1 versions prior to 18.1R2-S3, 18.1R3.

Receipt of a malformed packet on MX Series devices with dynamic vlan configuration can trigger an uncontrolled recursion loop in the Broadband Edge subscriber management daemon (bbe-smgd), and lead to high CPU usage and a crash of the bbe-smgd service. Repeated receipt of the same packet can result in an extended denial of service condition for the device. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S1; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S10, 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3-S1; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R3; 18.2 versions prior to 18.2R2.

A Denial of Service vulnerability in J-Web service may allow a remote unauthenticated user to cause Denial of Service which may prevent other users to authenticate or to perform J-Web operations. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D60 on SRX Series; 15.1 versions prior to 15.1R7; 15.1F6; 15.1X49 versions prior to 15.1X49-D120 on SRX Series; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400 Series; 15.1X53 versions prior to 15.1X53-D67 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D234 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D470, 15.1X53-D495 on NFX Series; 16.1 versions prior to 16.1R6; 16.2 versions prior to 16.2R2-S6, 16.2R3; 17.1 versions prior to 17.1R2-S6, 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R2. No other Juniper Networks products or platforms are affected by this issue.

Memory leak in Juniper JUNOS 6.4 through 8.0, built before May 10, 2006, allows remote attackers to cause a denial of service (kernel packet memory consumption and crash) via crafted IPv6 packets whose buffers are not released after they are processed.

Unknown vulnerability in ScreenOS in Juniper Networks NetScreen firewall 3.x through 5.x allows remote attackers to cause a denial of service (device reboot or hang) via a crafted SSH v1 packet.

TCP, when using a large Window Size, makes it easier for remote attackers to guess sequence numbers and cause a denial of service (connection loss) to persistent TCP connections by repeatedly injecting a TCP RST packet, especially in protocols that use long-lived connections, such as BGP.

Memory leak in Juniper JUNOS Packet Forwarding Engine (PFE) allows remote attackers to cause a denial of service (memory exhaustion and device reboot) via certain IPv6 packets.

Firewalls from multiple vendors empty state tables more slowly than they are filled, which allows remote attackers to flood state tables with packet flooding attacks such as (1) TCP SYN flood, (2) UDP flood, or (3) Crikey CRC Flood, which causes the firewall to refuse any new connections.