On Juniper Networks Junos OS platforms configured as DHCPv6 local server or DHCPv6 Relay Agent, the Juniper Networks Dynamic Host Configuration Protocol Daemon (JDHCPD) process might crash if a malformed DHCPv6 packet is received, resulting in a restart of the daemon. The daemon automatically restarts without intervention, but continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects DHCPv6. DHCPv4 is not affected by this issue. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R3-S7; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R3-S2; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R2.
A vulnerability in the handling of internal resources necessary to bring up a large number of Layer 2 broadband remote access subscriber (BRAS) nodes in Juniper Networks Junos OS can cause the Access Node Control Protocol daemon (ANCPD) to crash and restart, leading to a Denial of Service (DoS) condition. Continued processing of spoofed subscriber nodes will create a sustained Denial of Service (DoS) condition. When the number of subscribers attempting to connect exceeds the configured maximum-discovery-table-entries value, the subscriber fails to map to an internal neighbor entry, causing the ANCPD process to crash. This issue affects Juniper Networks Junos OS: All versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R2-S13; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R3-S8; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R2.
A vulnerability in Juniper Networks Junos OS running on the ACX5448 and ACX710 platforms may cause BFD sessions to flap when a high rate of transit ARP packets are received. This, in turn, may impact routing protocols and network stability, leading to a Denial of Service (DoS) condition. When a high rate of transit ARP packets are exceptioned to the CPU and BFD flaps, the following log messages may be seen: bfdd[15864]: BFDD_STATE_UP_TO_DOWN: BFD Session 192.168.14.3 (IFL 232) state Up -> Down LD/RD(17/19) Up time:11:38:17 Local diag: CtlExpire Remote diag: None Reason: Detect Timer Expiry. bfdd[15864]: BFDD_TRAP_SHOP_STATE_DOWN: local discriminator: 17, new state: down, interface: irb.998, peer addr: 192.168.14.3 rpd[15839]: RPD_ISIS_ADJDOWN: IS-IS lost L2 adjacency to peer on irb.998, reason: BFD Session Down bfdd[15864]: BFDD_TRAP_SHOP_STATE_UP: local discriminator: 17, new state: up, interface: irb.998, peer addr: 192.168.14.3 This issue only affects the ACX5448 Series and ACX710 Series routers. No other products or platforms are affected by this vulnerability. This issue affects Juniper Networks Junos OS: 18.2 versions prior to 18.2R3-S8 on ACX5448; 18.3 versions prior to 18.3R3-S5 on ACX5448; 18.4 versions prior to 18.4R1-S6, 18.4R3-S7 on ACX5448; 19.1 versions prior to 19.1R3-S5 on ACX5448; 19.2 versions prior to 19.2R2, 19.2R3 on ACX5448; 19.3 versions prior to 19.3R3 on ACX5448; 19.4 versions prior to 19.4R3 on ACX5448; 20.1 versions prior to 20.1R2 on ACX5448; 20.2 versions prior to 20.2R2 on ACX5448 and ACX710.
A vulnerability in the distributed or centralized periodic packet management daemon (PPMD) of Juniper Networks Junos OS may cause receipt of a malformed packet to crash and restart the PPMD process, leading to network destabilization, service interruption, and a Denial of Service (DoS) condition. Continued receipt and processing of these malformed packets will repeatedly crash the PPMD process and sustain the Denial of Service (DoS) condition. Due to the nature of the specifically crafted packet, exploitation of this issue requires direct, adjacent connectivity to the vulnerable component. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S12, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S5, 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S2, 20.2R2.
In Juniper Networks Junos OS Evolved an attacker sending certain valid BGP update packets may cause Junos OS Evolved to access an uninitialized pointer causing RPD to core leading to a Denial of Service (DoS). Continued receipt of these types of valid BGP update packets will cause an extended Denial of Service condition. RPD will require a restart to recover. An indicator of compromise is to see if the file rpd.re exists by issuing the command: show system core-dumps This issue affects: Juniper Networks Junos OS Evolved 19.4 versions prior to 19.4R2-S2-EVO; 20.1 versions prior to 20.1R1-S2-EVO, 20.1R2-S1-EVO. This issue does not affect Junos OS.
Improper Handling of Exceptional Conditions in Ethernet interface frame processing of Juniper Networks Junos OS allows an attacker to send specially crafted frames over the local Ethernet segment, causing the interface to go into a down state, resulting in a Denial of Service (DoS) condition. The interface does not recover on its own and the FPC must be reset manually. Continued receipt and processing of these frames will create a sustained Denial of Service (DoS) condition. This issue is platform-specific and affects the following platforms and line cards: * MPC7E/8E/9E and MPC10E on MX240, MX480, MX960, MX2008, MX2010, and MX2020 * MX204, MX10003, MX10008, MX10016 * EX9200, EX9251 * SRX4600 No other products or platforms are affected by this vulnerability. An indication of this issue occurring can be seen in the system log messages, as shown below: user@host> show log messages | match "Failed to complete DFE tuning" fpc4 smic_phy_dfe_tuning_state: et-4/1/6 - Failed to complete DFE tuning (count 3) and interface will be in a permanently down state: user@host> show interfaces et-4/1/6 terse Interface Admin Link Proto Local Remote et-4/1/6 up down et-4/1/6.0 up down aenet --> ae101.0 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S7 on MX Series; 17.1R1 and later versions prior to 17.2R3-S3 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S11, 17.4R3-S1 on MX Series, SRX4600; 18.1 versions prior to 18.1R3-S10 on MX Series, EX9200 Series, SRX4600; 18.2 versions prior to 18.2R3-S3 on MX Series, EX9200 Series, SRX4600; 18.3 versions prior to 18.3R3-S1 on MX Series, EX9200 Series, SRX4600; 18.4 versions prior to 18.4R2-S3, 18.4R3 on MX Series, EX9200 Series, SRX4600; 19.1 versions prior to 19.1R2-S1, 19.1R3 on MX Series, EX9200 Series, SRX4600; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series, EX9200 Series, SRX4600; 19.3 versions prior to 19.3R2 on MX Series, EX9200 Series, SRX4600. This issue does not affect Juniper Networks Junos OS versions prior to 16.1R1.
An Improper Validation of Syntactic Correctness of Input vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). If an attacker sends high rate of specific ICMP traffic to a device with VXLAN configured, this causes a deadlock of the PFE and results in the device becoming unresponsive. A manual restart will be required to recover the device. This issue only affects EX4100, EX4400, EX4600, QFX5000 Series devices. This issue affects: Juniper Networks Junos OS * 21.4R3 versions earlier than 21.4R3-S4; * 22.1R3 versions earlier than 22.1R3-S3; * 22.2R2 versions earlier than 22.2R3-S1; * 22.3 versions earlier than 22.3R2-S2, 22.3R3; * 22.4 versions earlier than 22.4R2; * 23.1 versions earlier than 23.1R2.
Unspecified vulnerability in Oracle MySQL Server 5.5.39 and earlier, and 5.6.20 and earlier, allows remote attackers to affect availability via vectors related to CLIENT:SSL:yaSSL, a different vulnerability than CVE-2014-6494.
Unspecified vulnerability in Oracle MySQL Server 5.5.39 and earlier, and 5.6.20 and earlier, allows remote attackers to affect availability via vectors related to CLIENT:SSL:yaSSL, a different vulnerability than CVE-2014-6496.
A Double Free vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on SRX Series allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). In a remote access VPN scenario, if a "tcp-encap-profile" is configured and a sequence of specific packets is received, a flowd crash and restart will be observed. This issue affects Juniper Networks Junos OS on SRX Series: * All versions earlier than 20.4R3-S8; * 21.2 versions earlier than 21.2R3-S6; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S3; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R2-S2, 22.4R3.
Unspecified vulnerability in Oracle MySQL Server 5.5.38 and earlier, and 5.6.19 and earlier, allows remote attackers to affect availability via vectors related to SERVER:SSL:yaSSL.
An Improper Neutralization of Equivalent Special Elements vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on PTX Series allows a unauthenticated, adjacent attacker to cause a Denial of Service (DoS). When MPLS packets are meant to be sent to a flexible tunnel interface (FTI) and if the FTI tunnel is down, these will hit the reject NH, due to which the packets get sent to the CPU and cause a host path wedge condition. This will cause the FPC to hang and requires a manual restart to recover. Please note that this issue specifically affects PTX1000, PTX3000, PTX5000 with FPC3, PTX10002-60C, and PTX10008/16 with LC110x. Other PTX Series devices and Line Cards (LC) are not affected. The following log message can be seen when the issue occurs: Cmerror Op Set: Host Loopback: HOST LOOPBACK WEDGE DETECTED IN PATH ID <id> (URI: /fpc/<fpc>/pfe/<pfe>/cm/<cm>/Host_Loopback/<cm>/HOST_LOOPBACK_MAKE_CMERROR_ID[<id>]) This issue affects Juniper Networks Junos OS: * All versions earlier than 20.4R3-S8; * 21.1 versions earlier than 21.1R3-S4; * 21.2 versions earlier than 21.2R3-S6; * 21.3 versions earlier than 21.3R3-S3; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R2-S2, 22.1R3; * 22.2 versions earlier than 22.2R2-S1, 22.2R3.
An Improper Check or Handling of Exceptional Conditions within the storm control feature of Juniper Networks Junos OS allows an attacker sending a high rate of traffic to cause a Denial of Service. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. Storm control monitors the level of applicable incoming traffic and compares it with the level specified. If the combined level of the applicable traffic exceeds the specified level, the switch drops packets for the controlled traffic types. This issue affects Juniper Networks Junos OS on QFX10002: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2.
An Improper Check for Unusual or Exceptional Conditions vulnerability in the Layer 2 Address Learning Daemon (l2ald) on Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause Denial of Service (DoS). In an EVPN/VXLAN scenario, when a high amount specific Layer 2 packets are processed by the device, it can cause the Routing Protocol Daemon (rpd) to utilize all CPU resources which causes the device to hang. A manual restart of the rpd is required to restore services. This issue affects both IPv4 and IPv6 implementations. This issue affects Junos OS: All versions earlier than 21.4R3-S7; 22.1 versions earlier than 22.1R3-S5; 22.2 versions earlier than 22.2R3-S3; 22.3 versions earlier than 22.3R3-S3; 22.4 versions earlier than 22.4R3-S2; 23.2 versions earlier than 23.2R2; 23.4 versions earlier than 23.4R1-S1. Junos OS Evolved: All versions earlier than 21.4R3-S7-EVO; 22.1-EVO versions earlier than 22.1R3-S5-EVO; 22.2-EVO versions earlier than 22.2R3-S3-EVO; 22.3-EVO versions earlier than 22.3R3-S3-EVO; 22.4-EVO versions earlier than 22.4R3-S2-EVO; 23.2-EVO versions earlier than 23.2R2-EVO; 23.4-EVO versions earlier than 23.4R1-S1-EVO, 23.4R2-EVO.
An Improper Handling of Exceptional Conditions vulnerability in the broadband edge subscriber management daemon (bbe-smgd) of Juniper Networks Junos OS on MX Series allows an attacker directly connected to the vulnerable system who repeatedly flaps DHCP subscriber sessions to cause a slow memory leak, ultimately leading to a Denial of Service (DoS). Memory can only be recovered by manually restarting bbe-smgd. This issue only occurs if BFD liveness detection for DHCP subscribers is enabled. Systems without BFD liveness detection enabled are not vulnerable to this issue. Indication of the issue can be observed by periodically executing the 'show system processes extensive' command, which will indicate an increase in memory allocation for bbe-smgd. A small amount of memory is leaked every time a DHCP subscriber logs in, which will become visible over time, ultimately leading to memory starvation. user@junos> show system processes extensive | match bbe-smgd 13071 root 24 0 415M 201M select 0 0:41 7.28% bbe-smgd{bbe-smgd} 13071 root 20 0 415M 201M select 1 0:04 0.00% bbe-smgd{bbe-smgd} ... user@junos> show system processes extensive | match bbe-smgd 13071 root 20 0 420M 208M select 0 4:33 0.10% bbe-smgd{bbe-smgd} 13071 root 20 0 420M 208M select 0 0:12 0.00% bbe-smgd{bbe-smgd} ... This issue affects Juniper Networks Junos OS on MX Series: * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S2; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2.
An Improper Check or Handling of Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). If an attacker sends a specific MPLS packet, which upon processing, causes an internal loop, that leads to a PFE crash and restart. Continued receipt of these packets leads to a sustained Denial of Service (DoS) condition. Circuit cross-connect (CCC) needs to be configured on the device for it to be affected by this issue. This issue only affects MX Series with MPC10, MPC11, LC9600, and MX304. This issue affects: Juniper Networks Junos OS 21.4 versions from 21.4R3 earlier than 21.4R3-S5; 22.2 versions from 22.2R2 earlier than 22.2R3-S2; 22.3 versions from 22.3R1 earlier than 22.3R2-S2; 22.3 versions from 22.3R3 earlier than 22.3R3-S1 22.4 versions from 22.4R1 earlier than 22.4R2-S2, 22.4R3; 23.2 versions earlier than 23.2R1-S1, 23.2R2.
An Incomplete Cleanup vulnerability in Nonstop active routing (NSR) component of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker to cause memory leak leading to Denial of Service (DoS). On all Junos OS platforms, when NSR is enabled, a BGP flap will cause memory leak. A manual reboot of the system will restore the services. Note: NSR is not supported on the SRX Series and is therefore not affected by this vulnerability. The memory usage can be monitored using the below commands. user@host> show chassis routing-engine no-forwarding user@host> show system memory | no-more This issue affects: Juniper Networks Junos OS * 21.2 versions earlier than 21.2R3-S5; * 21.3 versions earlier than 21.3R3-S4; * 21.4 versions earlier than 21.4R3-S4; * 22.1 versions earlier than 22.1R3-S2; * 22.2 versions earlier than 22.2R3-S2; * 22.3 versions earlier than 22.3R2-S1, 22.3R3; * 22.4 versions earlier than 22.4R1-S2, 22.4R2. This issue does not affect Junos OS versions earlier than 20.4R3-S7.
An Access of Memory Location After End of Buffer vulnerability in the Layer-2 Control Protocols Daemon (l2cpd) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent, unauthenticated attacker to cause Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, when LLDP is enabled on a specific interface, and a malformed LLDP packet is received, l2cpd crashes and restarts. The impact of the l2cpd crash is reinitialization of STP protocols (RSTP, MSTP or VSTP), and MVRP and ERP. Also, if any services depend on LLDP state (like PoE or VoIP device recognition), then these will also be affected. This issue affects: Junos OS: * from 21.4 before 21.4R3-S4, * from 22.1 before 22.1R3-S4, * from 22.2 before 22.2R3-S2, * from 22.3 before 22.3R2-S2, 22.3R3-S1, * from 22.4 before 22.4R3, * from 23.2 before 23.2R2. Junos OS Evolved: * from 21.4-EVO before 21.4R3-S5-EVO, * from 22.1-EVO before 22.1R3-S4-EVO, * from 22.2-EVO before 22.2R3-S2-EVO, * from 22.3-EVO before 22.3R2-S2-EVO, 22.3R3-S1-EVO, * from 22.4-EVO before 22.4R3-EVO, * from 23.2-EVO before 23.2R2-EVO. This issue does not affect: * Junos OS versions prior to 21.4R1; * Junos OS Evolved versions prior to 21.4R1-EVO.
A Missing Release of Memory after Effective Lifetime vulnerability in the IKE daemon (iked) of Juniper Networks Junos OS on MX Series with SPC3, and SRX Series allows an administratively adjacent attacker which is able to successfully establish IPsec tunnels to cause a Denial of Service (DoS). If specific values for the IPsec parameters local-ip, remote-ip, remote ike-id, and traffic selectors are sent from the peer, a memory leak occurs during every IPsec SA rekey which is carried out with a specific message sequence. This will eventually result in an iked process crash and restart. The iked process memory consumption can be checked using the below command: user@host> show system processes extensive | grep iked PID USERNAME PRI NICE SIZE RES STATE C TIME WCPU COMMAND 56903 root 31 0 4016M 2543M CPU0 0 2:10 10.50% iked This issue affects Juniper Networks Junos OS: * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S4; * 22.1 versions earlier than 22.1R3-S3; * 22.2 versions earlier than 22.2R3-S2; * 22.3 versions earlier than 22.3R3; * 22.4 versions earlier than 22.4R3; * 23.2 versions earlier than 23.2R1-S2, 23.2R2.
An Improper Validation of Syntactic Correctness of Input vulnerability in Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On all Junos OS MX Series and SRX Series platforms, when SIP ALG is enabled, and a specific SIP packet is received and processed, NAT IP allocation fails for genuine traffic, which causes Denial of Service (DoS). Continuous receipt of this specific SIP ALG packet will cause a sustained DoS condition. NAT IP usage can be monitored by running the following command. user@srx> show security nat resource-usage source-pool <source_pool_name> Pool name: source_pool_name .. Address Factor-index Port-range Used Avail Total Usage X.X.X.X 0 Single Ports 50258 52342 62464 96% <<<<< - Alg Ports 0 2048 2048 0% This issue affects: Juniper Networks Junos OS on MX Series and SRX Series * All versions earlier than 21.2R3-S6; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2.
When the 'bgp-error-tolerance' feature â€" designed to help mitigate remote session resets from malformed path attributes â€" is enabled, a BGP UPDATE containing a specifically crafted set of transitive attributes can cause the RPD routing process to crash and restart. Devices with BGP enabled that do not have 'bgp-error-tolerance' configured are not vulnerable to this issue. Affected releases are Juniper Networks Junos OS 13.3 prior to 13.3R10-S2; 14.1 prior to 14.1R8-S4, 14.1R9; 14.1X50 prior to 14.1X50-D185; 14.1X53 prior to 14.1X53-D45, 14.1X53-D50; 14.2 prior to 14.2R7-S7, 14.2R8; 15.1 prior to 15.1F5-S8, 15.1F6-S7, 15.1R5-S6, 15.1R6-S2, 15.1R7; 15.1X49 prior to 15.1X49-D100; 15.1X53 prior to 15.1X53-D64, 15.1X53-D70; 16.1 prior to 16.1R3-S4, 16.1R4-S3, 16.1R5; 16.2 prior to 16.2R1-S5, 16.2R2; 17.1 prior to 17.1R1-S3, 17.1R2; 17.2 prior to 17.2R1-S2, 17.2R2; 17.2X75 prior to 17.2X75-D50. No other Juniper Networks products or platforms are affected by this issue.
An Uncontrolled Resource Consumption vulnerability in the aftmand process of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to consume memory resources, resulting in a Denial of Service (DoS) condition. The processes do not recover on their own and must be manually restarted. This issue affects both IPv4 and IPv6. Changes in memory usage can be monitored using the following CLI command: user@device> show system memory node <fpc slot> | grep evo-aftmann This issue affects Junos OS Evolved: * All versions before 21.2R3-S8-EVO, * 21.3 versions before 21.3R3-S5-EVO, * 21.4 versions before 21.4R3-S5-EVO, * 22.1 versions before 22.1R3-S4-EVO, * 22.2 versions before 22.2R3-S4-EVO, * 22.3 versions before 22.3R3-S3-EVO, * 22.4 versions before 22.4R2-S2-EVO, 22.4R3-EVO, * 23.2 versions before 23.2R1-S1-EVO, 23.2R2-EVO.
A NULL Pointer Dereference vulnerability in Juniper Networks Junos OS Evolved on ACX7024, ACX7100-32C and ACX7100-48L allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). If a specific IPv4 UDP packet is received and sent to the Routing Engine (RE) packetio crashes and restarts which causes a momentary traffic interruption. Continued receipt of such packets will lead to a sustained DoS. This issue does not happen with IPv6 packets. This issue affects Juniper Networks Junos OS Evolved on ACX7024, ACX7100-32C and ACX7100-48L: * 21.4-EVO versions earlier than 21.4R3-S6-EVO; * 22.1-EVO versions earlier than 22.1R3-S5-EVO; * 22.2-EVO versions earlier than 22.2R2-S1-EVO, 22.2R3-EVO; * 22.3-EVO versions earlier than 22.3R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions earlier than 21.4R1-EVO.
On Junos devices with the BGP graceful restart helper mode enabled or the BGP graceful restart mechanism enabled, a BGP session restart on a remote peer that has the graceful restart mechanism enabled may cause the local routing protocol daemon (RPD) process to crash and restart. By simulating a specific BGP session restart, an attacker can repeatedly crash the RPD process causing prolonged denial of service (DoS). Graceful restart helper mode for BGP is enabled by default. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R2-S8; 17.1 versions prior to 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D92, 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S4, 17.4R2; 18.1 versions prior to 18.1R2. Junos OS releases prior to 16.1R1 are not affected.
An Improper Validation of Syntactic Correctness of Input vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). If a BGP update is received over an established BGP session which contains a tunnel encapsulation attribute with a specifically malformed TLV, rpd will crash and restart. This issue affects Juniper Networks Junos OS: * 20.4 versions 20.4R1 and later versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R3; * 23.2 versions earlier than 23.2R1-S2, 23.2R2; Junos OS Evolved: * 20.4-EVO versions 20.4R1-EVO and later versions earlier than 20.4R3-S9-EVO; * 21.2-EVO versions earlier than 21.2R3-S7-EVO; * 21.3-EVO versions earlier than 21.3R3-S5-EVO; * 21.4-EVO versions earlier than 21.4R3-S5-EVO; * 22.1-EVO versions earlier than 22.1R3-S4-EVO; * 22.2-EVO versions earlier than 22.2R3-S3-EVO; * 22.3-EVO versions earlier than 22.3R3-S1-EVO; * 22.4-EVO versions earlier than 22.4R3-EVO; * 23.2-EVO versions earlier than 23.2R1-S2-EVO, 23.2R2-EVO; This issue does not affect Juniper Networks * Junos OS versions earlier than 20.4R1; * Junos OS Evolved versions earlier than 20.4R1-EVO. This is a related but separate issue than the one described in JSA79095.
An Exposure of Resource to Wrong Sphere vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX 300 Series allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). Specific valid link-local traffic is not blocked on ports in STP blocked state but is instead sent to the control plane of the device. This leads to excessive resource consumption and in turn severe impact on all control and management protocols of the device. This issue affects Juniper Networks Junos OS: * 21.2 version 21.2R3-S3 and later versions earlier than 21.2R3-S6; * 22.1 version 22.1R3 and later versions earlier than 22.1R3-S4; * 22.2 version 22.2R2 and later versions earlier than 22.2R3-S2; * 22.3 version 22.3R2 and later versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2. This issue does not affect Juniper Networks Junos OS 21.4R1 and later versions of 21.4.
A Missing Release of Memory after Effective Lifetime vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). In a Juniper Flow Monitoring (jflow) scenario route churn that causes BGP next hops to be updated will cause a slow memory leak and eventually a crash and restart of rpd. Thread level memory utilization for the areas where the leak occurs can be checked using the below command: user@host> show task memory detail | match so_in so_in6 28 32 344450 11022400 344760 11032320 so_in 8 16 1841629 29466064 1841734 29467744 This issue affects: Junos OS * 21.4 versions earlier than 21.4R3; * 22.1 versions earlier than 22.1R3; * 22.2 versions earlier than 22.2R3. Junos OS Evolved * 21.4-EVO versions earlier than 21.4R3-EVO; * 22.1-EVO versions earlier than 22.1R3-EVO; * 22.2-EVO versions earlier than 22.2R3-EVO. This issue does not affect: Juniper Networks Junos OS versions earlier than 21.4R1. Juniper Networks Junos OS Evolved versions earlier than 21.4R1.
An Improper Check for Unusual or Exceptional Conditions vulnerability in Routing Protocol Daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based, unauthenticated attacker to cause rpd to crash, leading to Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, when NETCONF and gRPC are enabled, and a specific query is executed via Dynamic Rendering (DREND), rpd will crash and restart. Continuous execution of this specific query will cause a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS * 22.2 versions earlier than 22.2R2-S2, 22.2R3; * 22.3 versions earlier than 22.3R2, 22.3R3. Juniper Networks Junos OS Evolved * 22.2 versions earlier than 22.2R2-S2-EVO, 22.2R3-EVO; * 22.3 versions earlier than 22.3R2-EVO, 22.3R3-EVO. This issue does not affect Juniper Networks: Junos OS versions earlier than 22.2R1; Junos OS Evolved versions earlier than 22.2R1-EVO.
An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX Series and NFX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). If an affected device receives specific valid traffic destined to the device, it will cause the PFE to crash and restart. Continued receipt and processing of this traffic will create a sustained DoS condition. This issue affects Junos OS on SRX Series: * 21.4 versions before 21.4R3-S7.9, * 22.1 versions before 22.1R3-S5.3, * 22.2 versions before 22.2R3-S4.11, * 22.3 versions before 22.3R3, * 22.4 versions before 22.4R3. This issue affects Junos OS on NFX Series: * 21.4 versions before 21.4R3-S8, * 22.1 versions after 22.1R1, * 22.2 versions before 22.2R3-S5, * 22.3 versions before 22.3R3, * 22.4 versions before 22.4R3. Junos OS versions prior to 21.4R1 are not affected by this issue.
An Improper Input Validation vulnerability in Juniper Tunnel Driver (jtd) and ICMP module of Juniper Networks Junos OS Evolved allows an unauthenticated attacker within the MPLS administrative domain to send specifically crafted packets to the Routing Engine (RE) to cause a Denial of Service (DoS). When specifically crafted transit MPLS IPv4 packets are received by the Packet Forwarding Engine (PFE), these packets are internally forwarded to the RE. Continued receipt of these packets may create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: * All versions before 21.2R3-S8-EVO; * from 21.4-EVO before 21.4R3-S6-EVO; * from 22.2-EVO before 22.2R3-S4-EVO; * from 22.3-EVO before 22.3R3-S3-EVO; * from 22.4-EVO before 22.4R3-EVO; * from 23.2-EVO before 23.2R2-EVO. * from 23.4-EVO before 23.4R1-S1-EVO.
A Missing Release of Memory after Effective Lifetime vulnerability in Routing Protocol Daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause an rpd crash, leading to Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, when traffic engineering is enabled for OSPF or ISIS, and a link flaps, a patroot memory leak is observed. This memory leak, over time, will lead to an rpd crash and restart. The memory usage can be monitored using the below command. user@host> show task memory detail | match patroot This issue affects: Juniper Networks Junos OS * All versions earlier than 21.2R3-S3; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S3; * 22.1 versions earlier than 22.1R3; * 22.2 versions earlier than 22.2R3. Juniper Networks Junos OS Evolved * All versions earlier than 21.3R3-S5-EVO; * 21.4 versions earlier than 21.4R3-EVO; * 22.1 versions earlier than 22.1R3-EVO; * 22.2 versions earlier than 22.2R3-EVO.
named in ISC BIND 9.x before 9.9.8-P4 and 9.10.x before 9.10.3-P4 does not properly handle DNAME records when parsing fetch reply messages, which allows remote attackers to cause a denial of service (assertion failure and daemon exit) via a malformed packet to the rndc (aka control channel) interface, related to alist.c and sexpr.c.
Juniper Junos 10.0 before 10.0S28, 10.4 before 10.4R7, 11.1 before 11.1R5, 11.2 before 11.2R2, and 11.4 before 11.4R1, when in a Next-Generation Multicast VPN (NGEN MVPN) environment, allows remote attackers to cause a denial of service (RPD routing daemon crash) via a large number of crafted PIM (S,G) join requests.
An Uncontrolled Resource Consumption vulnerability in the HTTP daemon (httpd) of Juniper Networks Junos Space allows an unauthenticated network-based attacker flooding the device with inbound API calls to consume all resources on the system, leading to a Denial of Service (DoS). After continuously flooding the system with inbound connection requests, all available file handles become consumed, blocking access to the system via SSH and the web user interface (WebUI), resulting in a management interface DoS. A manual reboot of the system is required to restore functionality. This issue affects Junos Space: * all versions before 22.2R1 Patch V3, * from 23.1 before 23.1R1 Patch V3.
A Buffer Over-read vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). When an affected device receives a BGP update with a set of specific optional transitive attributes over an established peering session, rpd will crash and restart when attempting to advertise the received information to another peer. This issue can only happen if one or both of the BGP peers of the receiving session are non-4-byte-AS capable as determined from the advertised capabilities during BGP session establishment. Junos OS and Junos OS Evolved default behavior is 4-byte-AS capable unless this has been specifically disabled by configuring: [ protocols bgp ... disable-4byte-as ] Established BGP sessions can be checked by executing: show bgp neighbor <IP address> | match "4 byte AS" This issue affects: Junos OS: * all versions before 22.4R3-S8, * 23.2 versions before 23.2R2-S5, * 23.4 versions before 23.4R2-S6, * 24.2 versions before 24.2R2-S2, * 24.4 versions before 24.4R2; Junos OS Evolved: * all versions before 22.4R3-S8-EVO, * 23.2 versions before 23.2R2-S5-EVO, * 23.4 versions before 23.4R2-S6-EVO, * 24.2 versions before 24.2R2-S2-EVO, * 24.4 versions before 24.4R2-EVO.
A NULL Pointer Dereference vulnerability in the PFE management daemon (evo-pfemand) of Juniper Networks Junos OS Evolved on ACX7024, ACX7024X, ACX7100-32C, ACX7100-48L, ACX7348, ACX7509 devices allows an unauthenticated, adjacent attacker to cause a Denial-of-Service (DoS). Whenever specific valid multicast traffic is received on any layer 3 interface the evo-pfemand process crashes and restarts. Continued receipt of specific valid multicast traffic results in a sustained Denial of Service (DoS) attack. This issue affects Junos OS Evolved on ACX7024, ACX7024X, ACX7100-32C, ACX7100-48L, ACX7348, ACX7509: * from 23.2R2-EVO before 23.2R2-S4-EVO, * from 23.4R1-EVO before 23.4R2-EVO. This issue affects IPv4 and IPv6. This issue does not affect Junos OS Evolved ACX7024, ACX7024X, ACX7100-32C, ACX7100-48L, ACX7348, ACX7509 versions before 23.2R2-EVO.
An Improper Check for Unusual or Exceptional Conditions vulnerability in the processing of specific IPv6 packets on certain EX Series devices may lead to exhaustion of DMA memory causing a Denial of Service (DoS). Over time, exploitation of this vulnerability may cause traffic to stop being forwarded, or a crash of the fxpc process. An indication of the issue occurring may be observed through the following log messages: Sep 13 17:14:59 hostname : %PFE-3: fpc0 (buf alloc) failed allocating packet buffer Sep 13 17:14:59 hostname : %PFE-7: fpc0 brcm_pkt_buf_alloc:393 (buf alloc) failed allocating packet buffer When Packet DMA heap utilization reaches 99%, the system will become unstable. Packet DMA heap utilization can be monitored using the command: user@junos# request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 213301a8 536870488 387228840 149641648 27 Kernel 1 91800000 8388608 3735120 4653488 55 DMA 2 92000000 75497472 74452192 1045280 1 PKT DMA DESC 3 d330000 335544320 257091400 78452920 23 Bcm_sdk 4 96800000 184549376 2408 184546968 99 Packet DMA <<<< 5 903fffe0 20971504 20971504 0 0 Blob This issue affects: Juniper Networks Junos OS 18.4 versions prior to 18.4R2-S10, 18.4R3-S10 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.1 versions prior to 19.1R3-S7 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.3 versions prior to 19.3R3-S5 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.4 versions prior to 19.4R3-S7 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.1 versions prior to 20.1R3-S3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.2 versions prior to 20.2R3-S3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.3 versions prior to 20.3R3-S2 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.4 versions prior to 20.4R3-S1 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.1 versions prior to 21.1R2-S2, 21.1R3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.2 versions prior to 21.2R1-S2, 21.2R2 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.3 versions prior to 21.3R1-S1, 21.3R2 on EX2300 Series, EX2300-MP Series, EX3400 Series.
An Improper Handling of Exceptional Conditions vulnerability on specific PTX Series devices, including the PTX1000, PTX3000 (NextGen), PTX5000, PTX10002-60C, PTX10008, and PTX10016 Series, in Juniper Networks Junos OS allows an unauthenticated MPLS-based attacker to cause a Denial of Service (DoS) by triggering the dcpfe process to crash and FPC to restart. On affected PTX Series devices, processing specific MPLS packets received on an interface with multiple units configured may cause FPC to restart unexpectedly. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects PTX Series devices utilizing specific FPCs found on PTX1000, PTX3000 (NextGen), PTX5000, PTX10002-60C, PTX10008, and PTX10016 Series devices, only if multiple units are configured on the ingress interface, and at least one unit has 'family mpls' *not* configured. See the configuration sample below for more information. No other platforms are affected by this vulnerability. This issue affects: Juniper Networks Junos OS on PTX Series: All versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R3-S8; 20.1 versions prior to 20.1R3-S4; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2; 22.1 versions prior to 22.1R2.
An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker to cause a Denial of Service (DoS). If a BGP update message is received over an established BGP session, and that message contains a specific, optional transitive attribute, this session will be torn down with an update message error. This issue cannot propagate beyond an affected system as the processing error occurs as soon as the update is received. This issue is exploitable remotely as the respective attribute will propagate through unaffected systems and intermediate AS (if any). Continuous receipt of a BGP update containing this attribute will create a sustained Denial of Service (DoS) condition. Since this issue only affects 22.3R1, Juniper strongly encourages customers to move to 22.3R1-S1. Juniper SIRT felt that the need to promptly warn customers about this issue affecting the 22.3R1 versions of Junos OS and Junos OS Evolved warranted an Out of Cycle JSA. This issue affects: Juniper Networks Junos OS version 22.3R1. Juniper Networks Junos OS Evolved version 22.3R1-EVO. This issue does not affect: Juniper Networks Junos OS versions prior to 22.3R1. Juniper Networks Junos OS Evolved versions prior to 22.3R1-EVO.
An Improper Check for Unusual or Exceptional Conditions vulnerability in the packetIO daemon of Juniper Networks Junos OS Evolved on PTX10003, PTX10004, and PTX10008 allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). Continued receipt of these crafted packets will cause a sustained Denial of Service condition. This issue affects Juniper Networks Junos OS Evolved all versions prior to 20.4R2-S3-EVO on PTX10003, PTX10004, and PTX10008. This issue does not affect: Juniper Networks Junos OS Evolved versions 21.1R1-EVO and above; Juniper Networks Junos OS.
A Buffer Copy without Checking Size of Input ('Classic Buffer Overflow') vulnerability in the advanced forwarding toolkit (evo-aftmand/evo-pfemand) of Juniper Networks Junos OS Evolved on PTX Series or QFX5000 Series allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS).An attacker sending crafted multicast packets will cause line cards running evo-aftmand/evo-pfemand to crash and restart or non-line card devices to crash and restart. Continued receipt and processing of these packets will sustain the Denial of Service (DoS) condition. This issue affects Junos OS Evolved PTX Series: * All versions before 22.4R3-S8-EVO, * from 23.2 before 23.2R2-S5-EVO, * from 23.4 before 23.4R2-EVO, * from 24.2 before 24.2R2-EVO, * from 24.4 before 24.4R2-EVO. This issue affects Junos OS Evolved on QFX5000 Series: * 22.2-EVO version before 22.2R3-S7-EVO, * 22.4-EVO version before 22.4R3-S7-EVO, * 23.2-EVO versions before 23.2R2-S4-EVO, * 23.4-EVO versions before 23.4R2-S5-EVO, * 24.2-EVO versions before 24.2R2-S1-EVO, * 24.4-EVO versions before 24.4R1-S3-EVO, 24.4R2-EVO. This issue does not affect Junos OS Evolved on QFX5000 Series versions before: 21.2R2-S1-EVO, 21.2R3-EVO, 21.3R2-EVO, 21.4R1-EVO, and 22.1R1-EVO.
An Uncontrolled Memory Allocation vulnerability leading to a Heap-based Buffer Overflow in the packet forwarding engine (PFE) of Juniper Networks Junos OS allows a network-based unauthenticated attacker to flood the device with traffic leading to a Denial of Service (DoS). The device must be configured with storm control profiling limiting the number of unknown broadcast, multicast, or unicast traffic to be vulnerable to this issue. This issue affects: Juniper Networks Junos OS on QFX5100/QFX5110/QFX5120/QFX5200/QFX5210/EX4600/EX4650 Series; 20.2 version 20.2R1 and later versions prior to 20.2R2. This issue does not affect: Juniper Networks Junos OS versions prior to 20.2R1.
In VxLAN scenarios on EX4300-MP, EX4600, QFX5000 Series devices an Uncontrolled Memory Allocation vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated adjacently located attacker sending specific packets to cause a Denial of Service (DoS) condition by crashing one or more PFE's when they are received and processed by the device. Upon automatic restart of the PFE, continued processing of these packets will cause the memory leak to reappear. Depending on the volume of packets received the attacker may be able to create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on EX4300-MP, EX4600, QFX5000 Series: 17.1 version 17.1R1 and later versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S7, 19.2R3-S1; 19.3 versions prior to 19.3R2-S6, 19.3R3-S1; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2. This issue does not affect Junos OS versions prior to 17.1R1.
A Use of Uninitialized Resource vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX4700 devices allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When forwarding-options sampling is enabled, receipt of any traffic destined to the Routing Engine (RE) by the PFE line card leads to an FPC crash and restart, resulting in a Denial of Service (DoS). Continued receipt and processing of any traffic leading to the RE by the PFE line card will create a sustained Denial of Service (DoS) condition to the PFE line card. This issue affects Junos OS on SRX4700: * from 24.4 before 24.4R1-S3, 24.4R2 This issue affects IPv4 and IPv6.
An Improper Update of Reference Count vulnerability in the kernel of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to trigger a counter overflow, eventually causing a Denial of Service (DoS). This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R3-S1-EVO; 21.1 versions prior to 21.1R3-EVO; 21.2 versions prior to 21.2R3-EVO; 21.3 versions prior to 21.3R2-EVO. This issue does not affect Juniper Networks Junos OS.
An Improper Validation of Syntactic Correctness of Input vulnerability in the kernel of Juniper Networks Junos OS Evolved on PTX series allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). When an incoming TCP packet destined to the device is malformed there is a possibility of a kernel panic. Only TCP packets destined to the ports for BGP, LDP and MSDP can trigger this. This issue only affects PTX10004, PTX10008, PTX10016. No other PTX Series devices or other platforms are affected. This issue affects Juniper Networks Junos OS Evolved: 20.4-EVO versions prior to 20.4R3-S4-EVO; 21.3-EVO versions prior to 21.3R3-EVO; 21.4-EVO versions prior to 21.4R3-EVO; 22.1-EVO versions prior to 22.1R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 20.4R1-EVO.
An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based, attacker to cause Denial of Service (DoS). A PFE crash will happen when a GPRS Tunnel Protocol (GTP) packet is received with a malformed field in the IP header of GTP encapsulated General Packet Radio Services (GPRS) traffic. The packet needs to match existing state which is outside the attackers control, so the issue cannot be directly exploited. The issue will only be observed when endpoint address validation is enabled. This issue affects Juniper Networks Junos OS on SRX Series: 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2; 22.1 versions prior to 22.1R1-S1, 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.2R1.
An Incorrect Comparison vulnerability in PFE of Juniper Networks Junos OS allows an adjacent unauthenticated attacker to cause a Denial of Service (DoS). On QFX5000 Series, and EX4600 and EX4650 platforms, the fxpc process will crash followed by the FPC reboot upon receipt of a specific hostbound packet. Continued receipt of these specific packets will create a sustained Denial of Service (DoS) condition. This issue only affects Juniper Networks Junos OS 19.4 version 19.4R3-S4.
An Improper Input Validation vulnerability in the Juniper DHCP daemon (jdhcpd) of Juniper Networks Junos OS allows an adjacent unauthenticated attacker to cause a crash of jdhcpd and thereby a Denial of Service (DoS). If a device is configured as DHCPv6 local server and persistent storage is enabled, jdhcpd will crash when receiving a specific DHCPv6 message. This issue affects: Juniper Networks Junos OS All versions prior to 15.1R7-S11; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2; 21.2 versions prior to 21.2R2.
On QFX10000 Series devices using Juniper Networks Junos OS when configured as transit IP/MPLS penultimate hop popping (PHP) nodes with link aggregation group (LAG) interfaces, an Improper Validation of Specified Index, Position, or Offset in Input weakness allows an attacker sending certain IP packets to cause multiple interfaces in the LAG to detach causing a Denial of Service (DoS) condition. Continued receipt and processing of these packets will sustain the Denial of Service. This issue affects IPv4 and IPv6 packets. Packets of either type can cause and sustain the DoS event. These packets can be destined to the device or be transit packets. On devices such as the QFX10008 with line cards, line cards can be restarted to restore service. On devices such as the QFX10002 you can restart the PFE service, or reboot device to restore service. This issue affects: Juniper Networks Junos OS on QFX10000 Series: All versions prior to 15.1R7-S11; 18.4 versions prior to 18.4R2-S10, 18.4R3-S10; 19.1 versions prior to 19.1R3-S8; 19.2 versions prior to 19.2R3-S4; 19.3 versions prior to 19.3R3-S5; 19.4 versions prior to 19.4R2-S6, 19.4R3-S7; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S1. An indicator of compromise may be seen by issuing the command: request pfe execute target fpc0 command "show jspec pechip[3] registers ps l2_node 10" timeout 0 | refresh 1 | no-more and reviewing for backpressured output; for example: GOT: 0x220702a8 pe.ps.l2_node[10].pkt_cnt 00000076 GOT: 0x220702b4 pe.ps.l2_node[10].backpressured 00000002 <<<< STICKS HERE and requesting detail on the pepic wanio: request pfe execute target fpc0 command "show pepic 0 wanio-info" timeout 0 | no-more | match xe-0/0/0:2 GOT: 3 xe-0/0/0:2 10 6 3 0 1 10 189 10 0x6321b088 <<< LOOK HERE as well as looking for tail drops looking at the interface queue, for example: show interfaces queue xe-0/0/0:2 resulting in: Transmitted: Total-dropped packets: 1094137 0 pps << LOOK HERE