An Improper Check or Handling of Exceptional Conditions vulnerability in the UTM (Unified Threat Management) Web-Filtering feature of Juniper Networks Junos OS on SRX Series causes a jbuf memory leak to occur when accessing certain websites, eventually leading to a Denial of Service (DoS) condition. Service restoration is only possible by rebooting the system. The jbuf memory leak only occurs in SSL Proxy and UTM Web-Filtering configurations. Other products, platforms, and configurations are not affected by this vulnerability. This issue affects Juniper Networks Junos OS on SRX Series: 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R2-S1, 22.3R3; 22.4 versions prior to 22.4R1-S2, 22.4R2. This issue does not affect Juniper Networks Junos OS versions prior to 22.2R2.

An Improper Handling of Length Parameter Inconsistency vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network based, unauthenticated attacker to cause an RPD crash leading to a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Upon receipt of a malformed BGP flowspec update, RPD will crash resulting in a Denial of Service. This issue affects Juniper Networks Junos OS: All versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S1, 20.3R2; Juniper Networks Junos OS Evolved: All versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R2-EVO; 20.3 versions prior to 20.3R2-EVO;

An Improper Handling of Exceptional Conditions vulnerability in packet processing of Juniper Networks Junos OS on MX Series allows an unauthenticated network-based attacker to send specific packets to an Aggregated Multiservices (AMS) interface on the device, causing the packet forwarding engine (PFE) to crash, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue is only triggered by packets destined to a local-interface via a service-interface (AMS). AMS is only supported on the MS-MPC, MS-MIC, and MX-SPC3 cards. This issue is not experienced on other types of interfaces or configurations. Additionally, transit traffic does not trigger this issue. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S12; 20.2 versions prior to 20.2R3-S8; 20.4 versions prior to 20.4R3-S7; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S5; 21.3 versions prior to 21.3R3-S4; 21.4 versions prior to 21.4R3-S3; 22.1 versions prior to 22.1R3-S2; 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R2-S1, 22.3R3; 22.4 versions prior to 22.4R1-S2, 22.4R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on QFX10000 Series allows a network based attacker to cause a Denial of Service (DoS). If a specific valid IP packet is received and that packet needs to be routed over a VXLAN tunnel, this will result in a PFE wedge condition due to which traffic gets impacted. As this is not a crash and restart scenario, this condition will persist until the system is rebooted to recover. This issue affects Juniper Networks Junos OS on QFX10000: 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S5; 21.3 versions prior to 21.3R3-S4; 21.4 versions prior to 21.4R3-S1; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2; 22.3 versions prior to 22.3R1-S2, 22.3R2.

An Allocation of Resources Without Limits or Throttling vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). On QFX10K Series, Inter-Chassis Control Protocol (ICCP) is used in MC-LAG topologies to exchange control information between the devices in the topology. ICCP connection flaps and sync issues will be observed due to excessive specific traffic to the local device. This issue affects Juniper Networks Junos OS on QFX10K Series: * All versions prior to 20.2R3-S7; * 20.4 versions prior to 20.4R3-S4; * 21.1 versions prior to 21.1R3-S3; * 21.2 versions prior to 21.2R3-S1; * 21.3 versions prior to 21.3R3; * 21.4 versions prior to 21.4R3; * 22.1 versions prior to 22.1R2.

An issue was discovered in libslax through v0.22.1. A NULL pointer dereference exists in the function slaxLexer() located in slaxlexer.c. It allows an attacker to cause Denial of Service.

If extended statistics are enabled via 'set chassis extended-statistics', when executing any operation that fetches interface statistics, including but not limited to SNMP GET requests, the pfem process or the FPC may crash and restart. Repeated crashes of PFE processing can result in an extended denial of service condition. This issue only affects the following platforms: (1) EX2200, EX3300, XRE200 (2) MX Series routers with MPC7E/8E/9E PFEs installed, and only if 'extended-statistics' are enabled under the [edit chassis] configuration. Affected releases are Juniper Networks Junos OS 14.1 prior to 14.1R8-S5, 14.1R9 on MX Series; 14.1X53 prior to 14.1X53-D46, 14.1X53-D50 on EX2200, EX3300, XRE200; 14.2 prior to 14.2R7-S9, 14.2R8 on MX Series; 15.1 prior to 15.1F5-S8, 15.1F6-S8, 15.1R5-S3, 15.1R6 on MX Series; 16.1 prior to 16.1R4-S5, 16.1R5, 16.1R6 on MX Series; 16.1X65 prior to 16.1X65-D45 on EX2200, EX3300, XRE200; 16.2 prior to 16.2R2-S1, 16.2R3 on MX Series; 17.1 prior to 17.1R2-S2, 17.1R3 on MX Series; 17.2 prior to 17.2R1-S3, 17.2R2 on MX Series; 17.2X75 prior to 17.2X75-D50 on MX Series; 17.3 prior to 17.3R1-S1, 17.3R2 on MX Series. No other Juniper Networks products or platforms are affected by this issue.

An Uncontrolled Resource Consumption vulnerability in the kernel of Juniper Networks Junos OS allows an unauthenticated network based attacker to cause 100% CPU load and the device to become unresponsive by sending a flood of traffic to the out-of-band management ethernet port. Continued receipted of a flood will create a sustained Denial of Service (DoS) condition. Once the flood subsides the system will recover by itself. An indication that the system is affected by this issue would be that an irq handled by the fman process is shown to be using a high percentage of CPU cycles like in the following example output: user@host> show system processes extensive ... PID USERNAME PRI NICE SIZE RES STATE TIME WCPU COMMAND 31 root -84 -187 0K 16K WAIT 22.2H 56939.26% irq96: fman0 This issue affects Juniper Networks Junos OS: All versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S5; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R2-S2, 20.4R3; 21.1 versions prior to 21.1R2; 21.2 versions prior to 21.2R1-S1, 21.2R2.

An Improper Update of Reference Count vulnerability in the kernel of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to trigger a counter overflow, eventually causing a Denial of Service (DoS). This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R3-S1-EVO; 21.1 versions prior to 21.1R3-EVO; 21.2 versions prior to 21.2R3-EVO; 21.3 versions prior to 21.3R2-EVO. This issue does not affect Juniper Networks Junos OS.

A vulnerability in Juniper Networks Junos OS on SRX Series, allows a network-based unauthenticated attacker to cause a Denial of Service (DoS) by sending a specific fragmented packet to the device, resulting in a flowd process crash, which is responsible for packet forwarding. Continued receipt and processing of this specific packet will create a sustained DoS condition. This issue only affects SRX Series when 'preserve-incoming-fragment-size' feature is enabled. This issue affects Juniper Networks Junos OS on SRX Series: 18.3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R3-S10; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R2. This issue does not affect Juniper Networks Junos OS prior to 17.3R1.

An Improper Access Control vulnerability in Juniper Networks Junos OS Evolved allows a network-based unauthenticated attacker who is able to connect to a specific open IPv4 port, which in affected releases should otherwise be unreachable, to cause the CPU to consume all resources as more traffic is sent to the port to create a Denial of Service (DoS) condition. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS Evolved 20.4 versions prior to 20.4R3-S2-EVO; 21.1 versions prior to 21.1R3-S1-EVO; 21.2 versions prior to 21.2R3-EVO; 21.3 versions prior to 21.3R2-EVO; 21.4 versions prior to 21.4R2-EVO. This issue does not affect Junos OS.

An Access of Uninitialized Pointer vulnerability in SIP Application Layer Gateway (ALG) of Juniper Networks Junos OS on SRX Series and MX Series allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When specific valid SIP packets are received the PFE will crash and restart. This issue affects Juniper Networks Junos OS on SRX Series and MX Series: 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R2-S2, 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2; 22.1 versions prior to 22.1R1-S1, 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1.

An Insufficient Algorithmic Complexity combined with an Allocation of Resources Without Limits or Throttling vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on SRX Series and MX Series with SPC3 allows an unauthenticated network attacker to cause latency in transit packet processing and even packet loss. If transit traffic includes a significant percentage (> 5%) of fragmented packets which need to be reassembled, high latency or packet drops might be observed. This issue affects Juniper Networks Junos OS on SRX Series, MX Series with SPC3: All versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2-S9, 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R1-S1, 19.2R2.

On SRX Series devices, an Improper Check for Unusual or Exceptional Conditions when using Certificate Management Protocol Version 2 (CMPv2) auto re-enrollment, allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS) by crashing the pkid process. The pkid process cannot handle an unexpected response from the Certificate Authority (CA) server, leading to crash. A restart is required to restore services. This issue affects: Juniper Networks Junos OS on SRX Series: All versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S1; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R2.

An Improper Validation of Specified Type of Input vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS allows an attacker to cause an RPD memory leak leading to a Denial of Service (DoS). This memory leak only occurs when the attacker's packets are destined to any configured IPv6 address on the device. This issue affects: Juniper Networks Junos OS 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2; 22.1 versions prior to 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 21.1R1.

A Buffer Overflow vulnerability in the PFE of Juniper Networks Junos OS on SRX series allows an unauthenticated network based attacker to cause a Denial of Service (DoS). The PFE will crash when specific traffic is scanned by Enhanced Web Filtering safe-search feature of UTM (Unified Threat management). Continued receipt of this specific traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: 20.2 versions prior to 20.2R3-S4 on SRX Series; 20.3 versions prior to 20.3R3-S3 on SRX Series; 20.4 versions prior to 20.4R3-S3 on SRX Series; 21.1 versions prior to 21.1R3-S1 on SRX Series; 21.2 versions prior to 21.2R2-S2, 21.2R3 on SRX Series; 21.3 versions prior to 21.3R2 on SRX Series; 21.4 versions prior to 21.4R2 on SRX Series. This issue does not affect Juniper Networks Junos OS versions prior to 20.2R1.

A vulnerability in the NETISR network queue functionality of Juniper Networks Junos OS kernel allows an attacker to cause a Denial of Service (DoS) by sending crafted genuine packets to a device. During an attack, the routing protocol daemon (rpd) CPU may reach 100% utilization, yet FPC CPUs forwarding traffic will operate normally. This attack occurs when the attackers' packets are sent over an IPv4 unicast routing equal-cost multi-path (ECMP) unilist selection. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. An indicator of compromise may be to monitor NETISR drops in the network with the assistance of JTAC. Please contact JTAC for technical support for further guidance. This issue affects: Juniper Networks Junos OS 17.3 version 17.3R3-S9 and later versions prior to 17.3R3-S12; 17.4 version 17.4R3-S3 and later versions prior to 17.4R3-S5; 18.1 version 18.1R3-S11 and later versions prior to 18.1R3-S13; 18.2 version 18.2R3-S6 and later versions; 18.3 version 18.3R3-S4 and later versions prior to 18.3R3-S5; 18.4 version 18.4R3-S5 and later versions prior to 18.4R3-S9; 19.1 version 19.1R3-S3 and later versions prior to 19.1R3-S7. This issue does not affect Juniper Networks Junos OS versions prior to 17.3R3-S9. This issue does not affect Juniper Networks Junos OS Evolved.

An Improper Locking vulnerability in the SIP ALG of Juniper Networks Junos OS on MX Series and SRX Series allows an unauthenticated networked attacker to cause a flowprocessing daemon (flowd) crash and thereby a Denial of Service (DoS). Continued receipt of these specific packets will cause a sustained Denial of Service condition. This issue can occur in a scenario where the SIP ALG is enabled and specific SIP messages are being processed simultaneously. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series 20.4 versions prior to 20.4R3-S1; 21.1 versions prior to 21.1R2-S2, 21.1R3; 21.2 versions prior to 21.2R1-S2, 21.2R2; 21.3 versions prior to 21.3R1-S1, 21.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1.

On Juniper Networks Junos OS devices, a specific SNMP OID poll causes a memory leak which over time leads to a kernel crash (vmcore). Prior to the kernel crash other processes might be impacted, such as failure to establish SSH connection to the device. The administrator can monitor the output of the following command to check if there is memory leak caused by this issue: user@device> show system virtual-memory | match "pfe_ipc|kmem" pfe_ipc 147 5K - 164352 16,32,64,8192 <-- increasing vm.kmem_map_free: 127246336 <-- decreasing pfe_ipc 0 0K - 18598 32,8192 vm.kmem_map_free: 134582272 This issue affects Juniper Networks Junos OS: 17.4R3; 18.1 version 18.1R3-S5 and later versions prior to 18.1R3-S10; 18.2 version 18.2R3 and later versions prior to 18.2R3-S3; 18.2X75 version 18.2X75-D420, 18.2X75-D50 and later versions prior to 18.2X75-D430, 18.2X75-D53, 18.2X75-D60; 18.3 version 18.3R3 and later versions prior to 18.3R3-S2; 18.4 version 18.4R1-S4, 18.4R2 and later versions prior to 18.4R2-S5, 18.4R3-S1; 19.1 version 19.1R2 and later versions prior to 19.1R2-S2, 19.1R3; 19.2 version 19.2R1 and later versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S5, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2. This issue does not affect Juniper Networks Junos OS prior to 17.4R3.

An Improper Input Validation vulnerability in ingress TCP segment processing of Juniper Networks Junos OS Evolved allows a network-based unauthenticated attacker to send a crafted TCP segment to the device, triggering a kernel panic, leading to a Denial of Service (DoS) condition. Continued receipt and processing of this TCP segment could create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS Evolved: 21.3 versions prior to 21.3R3-EVO; 21.4 versions prior to 21.4R2-EVO; 22.1 versions prior to 22.1R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 21.3R1-EVO.

This issue occurs on Juniper Networks Junos OS devices which do not support Advanced Forwarding Interface (AFI) / Advanced Forwarding Toolkit (AFT). Devices using AFI and AFT are not exploitable to this issue. An improper initialization of memory in the packet forwarding architecture in Juniper Networks Junos OS non-AFI/AFT platforms which may lead to a Denial of Service (DoS) vulnerability being exploited when a genuine packet is received and inspected by non-AFT/AFI sFlow and when the device is also configured with firewall policers. This first genuine packet received and inspected by sampled flow (sFlow) through a specific firewall policer will cause the device to reboot. After the reboot has completed, if the device receives and sFlow inspects another genuine packet seen through a specific firewall policer, the device will generate a core file and reboot. Continued inspection of these genuine packets will create an extended Denial of Service (DoS) condition. Depending on the method for service restoration, e.g. hard boot or soft reboot, a core file may or may not be generated the next time the packet is received and inspected by sFlow. This issue affects: Juniper Networks Junos OS 17.4 versions prior to 17.4R2-S9, 17.4R3 on PTX1000 and PTX10000 Series, QFX10000 Series; 18.1 versions prior to 18.1R3-S9 on PTX1000 and PTX10000 Series, QFX10000 Series; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D30 on PTX1000 and PTX10000 Series, QFX10000 Series; 18.2 versions prior to 18.2R3 on PTX1000 and PTX10000 Series, QFX10000 Series; 18.3 versions prior to 18.3R3 on PTX1000 and PTX10000 Series, QFX10000 Series. This issue is not applicable to Junos OS versions before 17.4R1. This issue is not applicable to Junos OS Evolved or Junos OS with Advanced Forwarding Toolkit (AFT) forwarding implementations which use a different implementation of sFlow. The following example information is unrelated to this issue and is provided solely to assist you with determining if you have AFT or not. Example: A Junos OS device which supports the use of EVPN signaled VPWS with Flexible Cross Connect uses the AFT implementation. Since this configuration requires support and use of the AFT implementation to support this configuration, the device is not vulnerable to this issue as the sFlow implementation is different using the AFT architecture. For further details about AFT visit the AFI / AFT are in the links below. If you are uncertain if you use the AFI/AFT implementation or not, there are configuration examples in the links below which you may use to determine if you are vulnerable to this issue or not. If the commands work, you are. If not, you are not. You may also use the Feature Explorer to determine if AFI/AFT is supported or not. If you are still uncertain, please contact your support resources.

A vulnerability in the BGP FlowSpec implementation may cause a Juniper Networks Junos OS device to terminate an established BGP session upon receiving a specific BGP FlowSpec advertisement. The BGP NOTIFICATION message that terminates an established BGP session is sent toward the peer device that originally sent the specific BGP FlowSpec advertisement. This specific BGP FlowSpec advertisement received from a BGP peer might get propagated from a Junos OS device running the fixed release to another device that is vulnerable causing BGP session termination downstream. This issue affects IPv4 and IPv6 BGP FlowSpec deployment. This issue affects Juniper Networks Junos OS: 12.3; 12.3X48 on SRX Series; 14.1X53 on EX and QFX Series; 15.1 versions prior to 15.1R7-S5; 15.1F versions prior to 15.1F6-S13; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D497 on NFX Series; 15.1X53 versions prior to 15.1X53-D592 on EX2300/EX3400; 16.1 versions prior to 16.1R7-S7; 17.1 versions prior to 17.1R2-S12, 17.1R3; 17.2 versions prior to 17.2R2-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D102, 17.2X75-D110, 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions prior to 17.4R1-S8, 17.4R2; 18.1 versions prior to 18.1R2-S4, 18.1R3; 18.2X75 versions prior to 18.2X75-D20.

An Uncontrolled Memory Allocation vulnerability leading to a Heap-based Buffer Overflow in the packet forwarding engine (PFE) of Juniper Networks Junos OS allows a network-based unauthenticated attacker to flood the device with traffic leading to a Denial of Service (DoS). The device must be configured with storm control profiling limiting the number of unknown broadcast, multicast, or unicast traffic to be vulnerable to this issue. This issue affects: Juniper Networks Junos OS on QFX5100/QFX5110/QFX5120/QFX5200/QFX5210/EX4600/EX4650 Series; 20.2 version 20.2R1 and later versions prior to 20.2R2. This issue does not affect: Juniper Networks Junos OS versions prior to 20.2R1.

An Improper Validation of Syntactic Correctness of Input vulnerability in the kernel of Juniper Networks Junos OS Evolved on PTX series allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). When an incoming TCP packet destined to the device is malformed there is a possibility of a kernel panic. Only TCP packets destined to the ports for BGP, LDP and MSDP can trigger this. This issue only affects PTX10004, PTX10008, PTX10016. No other PTX Series devices or other platforms are affected. This issue affects Juniper Networks Junos OS Evolved: 20.4-EVO versions prior to 20.4R3-S4-EVO; 21.3-EVO versions prior to 21.3R3-EVO; 21.4-EVO versions prior to 21.4R3-EVO; 22.1-EVO versions prior to 22.1R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 20.4R1-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based, attacker to cause Denial of Service (DoS). A PFE crash will happen when a GPRS Tunnel Protocol (GTP) packet is received with a malformed field in the IP header of GTP encapsulated General Packet Radio Services (GPRS) traffic. The packet needs to match existing state which is outside the attackers control, so the issue cannot be directly exploited. The issue will only be observed when endpoint address validation is enabled. This issue affects Juniper Networks Junos OS on SRX Series: 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2; 22.1 versions prior to 22.1R1-S1, 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.2R1.

On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific UPDATE for an EBGP peer can lead to a routing process daemon (RPD) crash and restart. This issue occurs only when the device is receiving and processing the BGP UPDATE for an EBGP peer. This issue does not occur when the device is receiving and processing the BGP UPDATE for an IBGP peer. However, the offending BGP UPDATE can originally come from an EBGP peer, propagates through the network via IBGP peers without causing crash, then it causes RPD crash when it is processed for a BGP UPDATE towards an EBGP peer. Repeated receipt and processing of the same specific BGP UPDATE can result in an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 17.3R3-S6, 17.4R2-S7, and 18.1R3-S7. Juniper Networks Junos OS Evolved 19.2R2-EVO and later versions, prior to 19.3R1-EVO. Other Junos OS releases are not affected.

On Juniper Networks Junos OS and Junos OS Evolved devices, the receipt of a specific BGP UPDATE packet causes an internal counter to be incremented incorrectly, which over time can lead to the routing protocols process (RPD) crash and restart. This issue affects both IBGP and EBGP multihop deployment in IPv4 or IPv6 network. This issue affects: Juniper Networks Junos OS: 17.2X75 versions prior to 17.2X75-D105.19; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S4; 18.2X75 versions prior to 18.2X75-D13, 18.2X75-D411.1, 18.2X75-D420.18, 18.2X75-D52.3, 18.2X75-D60; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Juniper Networks Junos OS Evolved: any releases prior to 20.1R2-EVO. This issue does not affect Juniper Networks Junos OS releases prior to 17.3R1.

On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific BGP packet can lead to a routing process daemon (RPD) crash and restart. This issue can occur even before the BGP session with the peer is established. Repeated receipt of this specific BGP packet can result in an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 18.2X75 versions starting from 18.2X75-D50.8, 18.2X75-D60 and later versions, prior to 18.2X75-D52.8, 18.2X75-D53, 18.2X75-D60.2, 18.2X75-D65.1, 18.2X75-D70; 19.4 versions 19.4R1 and 19.4R1-S1; 20.1 versions prior to 20.1R1-S2, 20.1R2. Juniper Networks Junos OS Evolved: 19.4-EVO versions prior to 19.4R2-S2-EVO; 20.1-EVO versions prior to 20.1R2-EVO. This issue does not affect: Juniper Networks Junos OS releases prior to 19.4R1. Juniper Networks Junos OS Evolved releases prior to 19.4R1-EVO.

The FPC (Flexible PIC Concentrator) of Juniper Networks Junos OS and Junos OS Evolved may restart after processing a specific IPv4 packet. Only packets destined to the device itself, successfully reaching the RE through existing edge and control plane filtering, will be able to cause the FPC restart. When this issue occurs, all traffic via the FPC will be dropped. By continuously sending this specific IPv4 packet, an attacker can repeatedly crash the FPC, causing an extended Denial of Service (DoS) condition. This issue can only occur when processing a specific IPv4 packet. IPv6 packets cannot trigger this issue. This issue affects: Juniper Networks Junos OS on MX Series with MPC10E or MPC11E and PTX10001: 19.2 versions prior to 19.2R1-S4, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S1, 19.4R2. Juniper Networks Junos OS Evolved on on QFX5220, and PTX10003 series: 19.2-EVO versions; 19.3-EVO versions; 19.4-EVO versions prior to 19.4R2-EVO. This issue does not affect Junos OS versions prior to 19.2R1. This issue does not affect Junos OS Evolved versions prior to 19.2R1-EVO.

A vulnerability in Juniper Networks Junos OS Evolved may allow an attacker to cause a Denial of Service (DoS) by sending a high rate of specific packets to the device, resulting in a pfemand process crash. The pfemand process is responsible for packet forwarding on the device. By continuously sending the packet flood, an attacker can repeatedly crash the pfemand process causing a sustained Denial of Service. This issue can only be triggered by traffic sent to the device. Transit traffic does not cause this issue. This issue affects all version of Junos OS Evolved prior to 19.1R1-EVO.

Certain types of malformed Path Computation Element Protocol (PCEP) packets when received and processed by a Juniper Networks Junos OS device serving as a Path Computation Client (PCC) in a PCEP environment using Juniper's path computational element protocol daemon (pccd) process allows an attacker to cause the pccd process to crash and generate a core file thereby causing a Denial of Service (DoS). Continued receipt of this family of malformed PCEP packets will cause an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 15.1 versions prior to 15.1F6-S13, 15.1R7-S4; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238, 15.1X53-D496, 15.1X53-D592; 16.1 versions prior to 16.1R7-S4; 16.2 versions prior to 16.2R2-S9; 17.1 versions prior to 17.1R2-S11, 17.1R3; 17.2 versions prior to 17.2R1-S9; 17.2 version 17.2R2 and later prior to 17.2R3-S2; 17.3 versions prior to 17.3R3-S3; 17.4 versions prior to 17.4R2-S2, 17.4R3; 18.1 versions prior to 18.1R3-S2; 18.2 versions prior to 18.2R2-S6, 18.2R3; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R2; 18.4 versions prior to 18.4R1-S2, 18.4R2. This issue does not affect releases of Junos OS prior to 15.1R1.

When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of small fragments requiring reassembly, generating the following error messages: [LOG: Err] MQSS(2): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[2:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(2): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1960, QID 0 [LOG: Err] MQSS(2): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0xc38fb1 [LOG: Notice] Error: /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(2), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S9, 17.4R3-S1 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D34, 18.2X75-D41, 18.2X75-D53, 18.2X75-D65, 18.2X75-D430 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S2 on MX Series; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.

A vulnerability in Juniper Networks Junos OS on vMX and MX150 devices may allow an attacker to cause a Denial of Service (DoS) by sending specific packets requiring special processing in microcode that the flow cache can't handle, causing the riot forwarding daemon to crash. By continuously sending the same specific packets, an attacker can repeatedly crash the riot process causing a sustained Denial of Service. Flow cache is specific to vMX based products and the MX150, and is enabled by default in performance mode. This issue can only be triggered by traffic destined to the device. Transit traffic will not cause the riot daemon to crash. When the issue occurs, a core dump and riot log file entry are generated. For example: /var/crash/core.J-UKERN.mpc0.1557255993.3864.gz /home/pfe/RIOT logs: fpc0 riot[1888]: PANIC in lu_reorder_send_packet_postproc(): fpc0 riot[6655]: PANIC in lu_reorder_send_packet_postproc(): This issue affects Juniper Networks Junos OS: 18.1 versions prior to 18.1R3 on vMX and MX150; 18.2 versions prior to 18.2R3 on vMX and MX150; 18.2X75 versions prior to 18.2X75-D60 on vMX and MX150; 18.3 versions prior to 18.3R3 on vMX and MX150; 18.4 versions prior to 18.4R2 on vMX and MX150; 19.1 versions prior to 19.1R2 on vMX and MX150. This issue does not affect Junos OS versions prior to 18.1R1.

A race condition vulnerability on Juniper Network Junos OS devices may cause the routing protocol daemon (RPD) process to crash and restart while processing a BGP NOTIFICATION message. This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3; 17.2 version 17.2R2 and later versions; 17.2X75 versions prior to 17.2X75-D105, 17.2X75-D110; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S7, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R3-S3; 18.2X75 versions prior to 18.2X75-D410, 18.2X75-D420, 18.2X75-D50, 18.2X75-D60; 18.3 versions prior to 18.3R1-S5, 18.3R2-S2, 18.3R3; 18.4 versions prior to 18.4R2-S2, 18.4R3; 19.1 versions prior to 19.1R1-S2, 19.1R2; 19.2 versions prior to 19.2R1-S4, 19.2R2. This issue does not affect Juniper Networks Junos OS prior to version 16.1R1.

Receipt of a specific MPLS or IPv6 packet on the core facing interface of an MX Series device configured for Broadband Edge (BBE) service may trigger a kernel crash (vmcore), causing the device to reboot. The issue is specific to the processing of packets destined to BBE clients connected to MX Series subscriber management platforms. This issue affects MX Series running Juniper Networks Junos OS: 17.2 versions starting from17.2R2-S6, 17.2R3 and later releases, prior to 17.2R3-S3; 17.3 versions starting from 17.3R2-S4, 17.3R3-S2 and later releases, prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions starting from 17.4R2 and later releases, prior to 17.4R2-S7,17.4R3; 18.1 versions starting from 18.1R2-S3, 18.1R3 and later releases, prior to 18.1R3-S6; 18.2 versions starting from18.2R1-S1, 18.2R2 and later releases, prior to 18.2R3-S2; 18.2X75 versions prior to 18.2X75-D51, 18.2X75-D60; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S2, 19.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R2-S6.

On Juniper Networks Junos OS platforms configured as DHCPv6 local server or DHCPv6 Relay Agent, Juniper Networks Dynamic Host Configuration Protocol Daemon (JDHCPD) process might crash with a core dump if a malformed DHCPv6 packet is received, resulting with the restart of the daemon. This issue only affects DHCPv6, it does not affect DHCPv4. This issue affects: Juniper Networks Junos OS 17.4 versions prior to 17.4R2-S12, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.2X75 versions prior to 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.2 version 19.2R2 and later versions; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2; This issue does not affect Juniper Networks Junos OS prior to 17.4R1.

On Juniper Networks PTX and QFX Series devices with packet sampling configured using tunnel-observation mpls-over-udp, sampling of a malformed packet can cause the Kernel Routing Table (KRT) queue to become stuck. KRT is the module within the Routing Process Daemon (RPD) that synchronized the routing tables with the forwarding tables in the kernel. This table is then synchronized to the Packet Forwarding Engine (PFE) via the KRT queue. Thus, when KRT queue become stuck, it can lead to unexpected packet forwarding issues. An administrator can monitor the following command to check if there is the KRT queue is stuck: user@device > show krt state ... Number of async queue entries: 65007 <--- this value keep on increasing. When this issue occurs, the following message might appear in the /var/log/messages: DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Too many delayed route/nexthop unrefs. Op 2 err 55, rtsm_id 5:-1, msg type 2 DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Memory usage of M_RTNEXTHOP type = (0) Max size possible for M_RTNEXTHOP type = (7297134592) Current delayed unref = (60000), Current unique delayed unref = (18420), Max delayed unref on this platform = (40000) Current delayed weight unref = (60000) Max delayed weight unref on this platform= (400000) curproc = rpd This issue affects Juniper Networks Junos OS on PTX/QFX Series: 17.2X75 versions prior to 17.2X75-D105; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.2X75 versions prior to 18.2X75-D420, 18.2X75-D53, 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R1-S7, 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2. This issue does not affect Juniper Networks Junos OS prior to 18.1R1.

An Improper Validation of Syntactic Correctness of Input vulnerability in the Web-Filtering module of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). If an SRX device configured for UTM Web-Filtering receives a specifically malformed SSL packet, this will cause an FPC crash and restart. This issue affects Junos OS on SRX Series: * 23.2 versions from 23.2R2-S2 before 23.2R2-S5,  * 23.4 versions from 23.4R2-S1 before 23.4R2-S5, * 24.2 versions before 24.2R2-S2, * 24.4 versions before 24.4R1-S3, 24.4R2. Earlier versions of Junos are also affected, but no fix is available.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (pfe) of Juniper Networks Junos OS on MX Series allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). If specific traffic is received on MX Series and its rate exceeds the respective DDoS protection limit the ingress PFE will crash and restart. Continued receipt of this traffic will create a sustained DoS condition. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S5; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2.

A Use of Uninitialized Resource vulnerability in the Border Gateway Protocol (BGP) software of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker to send specific genuine BGP packets to a device configured with BGP to cause a Denial of Service (DoS) by crashing the Routing Protocol Daemon (rpd). This issue is triggered when the packets attempt to initiate a BGP connection before a BGP session is successfully established. Continued receipt of these specific BGP packets will cause a sustained Denial of Service condition. This issue is triggerable in both iBGP and eBGP deployments. This issue affects: Juniper Networks Junos OS 21.1 version 21.1R1 and later versions prior to 21.1R3-S5; 21.2 version 21.2R1 and later versions prior to 21.2R3-S2; 21.3 version 21.3R1 and later versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 21.1R1. This issue affects: Juniper Networks Junos OS Evolved 21.1-EVO version 21.1R1-EVO and later versions prior to 21.4R3-EVO; 22.1-EVO versions prior to 22.1R3-EVO; 22.2-EVO versions prior to 22.2R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 21.1R1-EVO.

A Missing Release of Memory after Effective Lifetime vulnerability in the routing protocol daemon of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network based attacker to cause a Denial of Service (DoS). In a BGP rib sharding scenario, when an attribute of an active BGP route is updated memory will leak. As rpd memory usage increases over time the rpd process will eventually run out of memory, crash, and restart. The memory utilization can be monitored with the following CLI commands: show task memory show system processes extensive | match rpd This issue affects: Juniper Networks Junos OS 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2. Juniper Networks Junos OS Evolved 20.3-EVO version 20.3R1-EVO and later versions; 20.4-EVO versions prior to 20.4R3-S6-EVO; 21.2-EVO versions prior to 21.2R3-EVO; 21.3-EVO versions prior to 21.3R2-EVO.

An Improper Check or Handling of Exceptional Conditions within the storm control feature of Juniper Networks Junos OS allows an attacker sending a high rate of traffic to cause a Denial of Service. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. Storm control monitors the level of applicable incoming traffic and compares it with the level specified. If the combined level of the applicable traffic exceeds the specified level, the switch drops packets for the controlled traffic types. This issue affects Juniper Networks Junos OS on QFX10002: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2.

An Improper Validation of Syntactic Correctness of Input vulnerability in Intrusion Detection and Prevention (IDP) of Juniper Networks SRX Series and MX Series allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). Continued receipt of this specific packet will cause a sustained Denial of Service condition. On all SRX Series and MX Series platforms, where IDP is enabled and a specific malformed SSL packet is received, the SSL detector crashes leading to an FPC core. This issue affects Juniper Networks SRX Series and MX Series prior to SigPack 3598. In order to identify the current SigPack version, following command can be used: user@junos# show security idp security-package-version

The Routing Engine in Juniper Junos OS 13.2R5 through 13.2R8, 13.3R1 before 13.3R8, 13.3R7 before 13.3R7-S3, 14.1R1 before 14.1R6, 14.1R3 before 14.1R3-S9, 14.1R4 before 14.1R4-S7, 14.1X51 before 14.1X51-D65, 14.1X53 before 14.1X53-D12, 14.1X53 before 14.1X53-D28, 14.1X53 before 4.1X53-D35, 14.2R1 before 14.2R5, 14.2R3 before 14.2R3-S4, 14.2R4 before 14.2R4-S1, 15.1 before 15.1R3, 15.1F2 before 15.1F2-S2, and 15.1X49 before 15.1X49-D40, when LDP is enabled, allows remote attackers to cause a denial of service (RPD routing process crash) via a crafted LDP packet.

On MX Series platforms with MS-MPC/MS-MIC, an Allocation of Resources Without Limits or Throttling vulnerability in Juniper Networks Junos OS allows an unauthenticated network attacker to cause a partial Denial of Service (DoS) with a high rate of specific traffic. If a Class of Service (CoS) rule is attached to the service-set and a high rate of specific traffic is processed by this service-set, for some of the other traffic which has services applied and is being processed by this MS-MPC/MS-MIC drops will be observed. Continued receipted of this high rate of specific traffic will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on MX Series with MS-MPC/MS-MIC: All versions prior to 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2.

An Improper Handling of Exceptional Conditions vulnerability in Juniper Networks Junos OS and Junos OS Evolved allows an attacker to inject a specific BGP update, causing the routing protocol daemon (RPD) to crash and restart, leading to a Denial of Service (DoS). Continued receipt and processing of the BGP update will create a sustained Denial of Service (DoS) condition. This issue affects very specific versions of Juniper Networks Junos OS: 19.3R3-S2; 19.4R3-S3; 20.2 versions 20.2R2-S3 and later, prior to 20.2R3-S2; 20.3 versions 20.3R2 and later, prior to 20.3R3; 20.4 versions 20.4R2 and later, prior to 20.4R3; 21.1 versions prior to 21.1R2. Juniper Networks Junos OS 20.1 is not affected by this issue. This issue also affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R2-S3-EVO, 20.4R3-EVO; 21.1-EVO versions prior to 21.1R2-EVO; 21.2-EVO versions prior to 21.2R2-EVO.