An Uncontrolled Resource Consumption vulnerability in the http daemon (httpd) of Juniper Networks Junos OS on SRX Series, QFX Series, MX Series and EX Series allows an unauthenticated, network-based attacker to cause Denial-of-Service (DoS). An attacker can send specific HTTPS connection requests to the device, triggering the creation of processes that are not properly terminated. Over time, this leads to resource exhaustion, ultimately causing the device to crash and restart. The following command can be used to monitor the resource usage: user@host> show system processes extensive | match mgd | count This issue affects Junos OS on SRX Series and EX Series: All versions before 21.4R3-S7, from 22.2 before 22.2R3-S4, from 22.3 before 22.3R3-S3, from 22.4 before 22.4R3-S2, from 23.2 before 23.2R2-S1, from 23.4 before 23.4R1-S2, 23.4R2.

An Uncontrolled Resource Consumption vulnerability in the aftmand process of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to consume memory resources, resulting in a Denial of Service (DoS) condition. The processes do not recover on their own and must be manually restarted. This issue affects both IPv4 and IPv6.  Changes in memory usage can be monitored using the following CLI command: user@device> show system memory node <fpc slot> | grep evo-aftmann This issue affects Junos OS Evolved:  * All versions before 21.2R3-S8-EVO,  * 21.3 versions before 21.3R3-S5-EVO,  * 21.4 versions before 21.4R3-S5-EVO,  * 22.1 versions before 22.1R3-S4-EVO,  * 22.2 versions before 22.2R3-S4-EVO, * 22.3 versions before 22.3R3-S3-EVO, * 22.4 versions before 22.4R2-S2-EVO, 22.4R3-EVO,  * 23.2 versions before 23.2R1-S1-EVO, 23.2R2-EVO.

A memory leak vulnerability in the of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the device by sending specific commands from a peered BGP host and having those BGP states delivered to the vulnerable device. This issue affects: Juniper Networks Junos OS: 18.1 versions prior to 18.1R2-S4, 18.1R3-S1; 18.1X75 all versions. Versions before 18.1R1 are not affected.

Specific IPv6 DHCP packets received by the jdhcpd daemon will cause a memory resource consumption issue to occur on a Junos OS device using the jdhcpd daemon configured to respond to IPv6 requests. Once started, memory consumption will eventually impact any IPv4 or IPv6 request serviced by the jdhcpd daemon, thus creating a Denial of Service (DoS) condition to clients requesting and not receiving IP addresses. Additionally, some clients which were previously holding IPv6 addresses will not have their IPv6 Identity Association (IA) address and network tables agreed upon by the jdhcpd daemon after the failover event occurs, which leads to more than one interface, and multiple IP addresses, being denied on the client. Affected releases are Juniper Networks Junos OS: 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R2.

An Uncontrolled Resource Consumption vulnerability in the HTTP daemon (httpd) of Juniper Networks Junos Space allows an unauthenticated network-based attacker flooding the device with inbound API calls to consume all resources on the system, leading to a Denial of Service (DoS). After continuously flooding the system with inbound connection requests, all available file handles become consumed, blocking access to the system via SSH and the web user interface (WebUI), resulting in a management interface DoS. A manual reboot of the system is required to restore functionality. This issue affects Junos Space: * all versions before 22.2R1 Patch V3, * from 23.1 before 23.1R1 Patch V3.

An Uncontrolled Resource Consumption vulnerability in the H.323 ALG (Application Layer Gateway) of  Juniper Networks Junos OS on SRX Series and MX Series with SPC3 and MS-MPC/MIC, allows an unauthenticated network-based attacker to send specific packets causing traffic loss leading to Denial of Service (DoS).  Continued receipt and processing of these specific packets will sustain the Denial of Service condition. The memory usage can be monitored using the below command.   user@host> show usp memory segment sha data objcache jsf  This issue affects SRX Series and MX Series with SPC3 and MS-MPC/MIC:  *  20.4 before 20.4R3-S10,  *  21.2 before 21.2R3-S6,  *  21.3 before 21.3R3-S5,  *  21.4 before 21.4R3-S6,  *  22.1 before 22.1R3-S4,  *  22.2 before 22.2R3-S2,  *  22.3 before 22.3R3-S1,  *  22.4 before 22.4R3,  *  23.2 before 23.2R2.

An Uncontrolled Resource Consumption vulnerability in the kernel of Juniper Networks Junos OS allows an unauthenticated network based attacker to cause 100% CPU load and the device to become unresponsive by sending a flood of traffic to the out-of-band management ethernet port. Continued receipted of a flood will create a sustained Denial of Service (DoS) condition. Once the flood subsides the system will recover by itself. An indication that the system is affected by this issue would be that an irq handled by the fman process is shown to be using a high percentage of CPU cycles like in the following example output: user@host> show system processes extensive ... PID USERNAME PRI NICE SIZE RES STATE TIME WCPU COMMAND 31 root -84 -187 0K 16K WAIT 22.2H 56939.26% irq96: fman0 This issue affects Juniper Networks Junos OS: All versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S5; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R2-S2, 20.4R3; 21.1 versions prior to 21.1R2; 21.2 versions prior to 21.2R1-S1, 21.2R2.

An Uncontrolled Resource Consumption vulnerability in the kernel of Juniper Networks JUNOS OS allows an unauthenticated network based attacker to cause 100% CPU load and the device to become unresponsive by sending a flood of traffic to the out-of-band management ethernet port. Continued receipted of a flood will create a sustained Denial of Service (DoS) condition. Once the flood subsides the system will recover by itself. An indication that the system is affected by this issue would be that kernel and netisr process are shown to be using a lot of CPU cycles like in the following example output: user@host> show system processes extensive ... PID USERNAME PRI NICE SIZE RES STATE C TIME WCPU COMMAND 16 root -72 - 0K 304K WAIT 1 839:40 88.96% intr{swi1: netisr 0} 0 root 97 - 0K 160K RUN 1 732:43 87.99% kernel{bcm560xgmac0 que} This issue affects Juniper Networks JUNOS OS on EX2300 Series, EX3400 Series, and ACX710: All versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S9; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2.

Receipt of specially crafted UDP/IP packets over MPLS may be able to bypass a stateless firewall filter. The crafted UDP packets must be encapsulated and meet a very specific packet format to be classified in a way that bypasses IP firewall filter rules. The packets themselves do not cause a service interruption (e.g. RPD crash), but receipt of a high rate of UDP packets may be able to contribute to a denial of service attack. This issue only affects processing of transit UDP/IP packets over MPLS, received on an interface with MPLS enabled. TCP packet processing and non-MPLS encapsulated UDP packet processing are unaffected by this issue. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D76; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D66, 12.3X48-D70; 14.1X53 versions prior to 14.1X53-D47; 15.1 versions prior to 15.1F6-S10, 15.1R4-S9, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D131, 15.1X49-D140; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400; 15.1X53 versions prior to 15.1X53-D67 on QFX10K; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX; 16.1 versions prior to 16.1R3-S8, 16.1R4-S9, 16.1R5-S4, 16.1R6-S3, 16.1R7; 16.2 versions prior to 16.2R1-S6, 16.2R2-S5, 16.2R3; 17.1 versions prior to 17.1R1-S7, 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S6, 17.2R2-S4, 17.2R3; 17.2X75 versions prior to 17.2X75-D100; 17.3 versions prior to 17.3R1-S4, 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S3, 17.4R2; 18.1 versions prior to 18.1R2; 18.2X75 versions prior to 18.2X75-D5.

On Juniper Networks SRX Series devices with link aggregation (lag) configured, executing any operation that fetches Aggregated Ethernet (AE) interface statistics, including but not limited to SNMP GET requests, causes a slow kernel memory leak. If all the available memory is consumed, the traffic will be impacted and a reboot might be required. The following log can be seen if this issue happens. /kernel: rt_pfe_veto: Memory over consumed. Op 1 err 12, rtsm_id 0:-1, msg type 72 /kernel: rt_pfe_veto: free kmem_map memory = (20770816) curproc = kmd An administrator can use the following CLI command to monitor the status of memory consumption (ifstat bucket): user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 2588977 162708K - 19633958 <<<< user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 3021629 189749K - 22914415 <<<< This issue affects Juniper Networks Junos OS on SRX Series: 17.1 versions 17.1R3 and above prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S5; 18.2 versions prior to 18.2R3-S7, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS prior to 17.1R3.

A vulnerability in Juniper Networks Junos OS ACX500 Series, ACX4000 Series, may allow an attacker to cause a Denial of Service (DoS) by sending a high rate of specific packets to the device, resulting in a Forwarding Engine Board (FFEB) crash. Continued receipt of these packets will sustain the Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on ACX500 Series, ACX4000 Series: 17.4 versions prior to 17.4R3-S2.

On Juniper Networks MX Series and EX9200 Series platforms with Trio-based MPC (Modular Port Concentrator) where Integrated Routing and Bridging (IRB) interface is configured and it is mapped to a VPLS instance or a Bridge-Domain, certain network events at Customer Edge (CE) device may cause memory leak in the MPC which can cause an out of memory and MPC restarts. When this issue occurs, there will be temporary traffic interruption until the MPC is restored. An administrator can use the following CLI command to monitor the status of memory usage level of the MPC: user@device> show system resource-monitor fpc FPC Resource Usage Summary Free Heap Mem Watermark : 20 % Free NH Mem Watermark : 20 % Free Filter Mem Watermark : 20 % * - Watermark reached Slot # % Heap Free RTT Average RTT 1 87 PFE # % ENCAP mem Free % NH mem Free % FW mem Free 0 NA 88 99 1 NA 89 99 When the issue is occurring, the value of “% NH mem Free” will go down until the MPC restarts. This issue affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines). Please refer to https://kb.juniper.net/KB25385 for the list of Trio-based PFEs. This issue affects Juniper Networks Junos OS on MX Series, EX9200 Series: 17.3R3-S8; 17.4R3-S2; 18.2R3-S4, 18.2R3-S5; 18.3R3-S2, 18.3R3-S3; 18.4 versions starting from 18.4R3-S1 and later versions prior to 18.4R3-S6; 19.2 versions starting from 19.2R2 and later versions prior to 19.2R3-S1; 19.4 versions starting from 19.4R2 and later versions prior to 19.4R2-S3, 19.4R3; 20.2 versions starting from 20.2R1 and later versions prior to 20.2R1-S3, 20.2R2. This issue does not affect Juniper Networks Junos OS: 18.1, 19.1, 19.3, 20.1.

An uncontrolled resource consumption vulnerability in Juniper Networks Junos OS on QFX5000 Series and EX4600 Series switches allows an attacker sending large amounts of legitimate traffic destined to the device to cause Interchassis Control Protocol (ICCP) interruptions, leading to an unstable control connection between the Multi-Chassis Link Aggregation Group (MC-LAG) nodes which can in turn lead to traffic loss. Continued receipt of this amount of traffic will create a sustained Denial of Service (DoS) condition. An indication that the system could be impacted by this issue is the following log message: "DDOS_PROTOCOL_VIOLATION_SET: Warning: Host-bound traffic for protocol/exception LOCALNH:aggregate exceeded its allowed bandwidth at fpc <fpc number> for <n> times, started at <timestamp>" This issue affects Juniper Networks Junos OS on QFX5000 Series and EX4600 Series: 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S7; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R1-S1, 20.4R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on MX Series allows a unauthenticated network-based attacker to cause an infinite loop, resulting in a Denial of Service (DoS). An attacker who sends malformed TCP traffic via an interface configured with PPPoE, causes an infinite loop on the respective PFE. This results in consuming all resources and a manual restart is needed to recover. This issue affects interfaces with PPPoE configured and tcp-mss enabled. This issue affects Juniper Networks Junos OS * All versions prior to 20.4R3-S7; * 21.1 version 21.1R1 and later versions; * 21.2 versions prior to 21.2R3-S6; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S3; * 22.1 versions prior to 22.1R3-S4; * 22.2 versions prior to 22.2R3; * 22.3 versions prior to 22.3R2-S2; * 22.4 versions prior to 22.4R2;

An Uncontrolled Resource Consumption vulnerability in TCP processing on the Routing Engine (RE) of Juniper Networks Junos OS allows an unauthenticated network-based attacker to send crafted TCP packets destined to the device, resulting in an MBUF leak that ultimately leads to a Denial of Service (DoS). The system does not recover automatically and must be manually restarted to restore service. This issue occurs when crafted TCP packets are sent directly to a configured IPv4 or IPv6 interface on the device. Transit traffic will not trigger this issue. MBUF usage can be monitored through the use of the 'show system buffers' command. For example: user@junos> show system buffers | refresh 5 4054/566/4620 mbufs in use (current/cache/total) ... 4089/531/4620 mbufs in use (current/cache/total) ... 4151/589/4740 mbufs in use (current/cache/total) ... 4213/527/4740 mbufs in use (current/cache/total) This issue affects Juniper Networks Junos OS: 12.3 version 12.3R12-S19 and later versions; 15.1 version 15.1R7-S10 and later versions; 17.3 version 17.3R3-S12 and later versions; 18.4 version 18.4R3-S9 and later versions; 19.1 version 19.1R3-S7 and later versions; 19.2 version 19.2R3-S3 and later versions; 19.3 version 19.3R2-S7, 19.3R3-S3 and later versions prior to 19.3R3-S7; 19.4 version 19.4R2-S7, 19.4R3-S5 and later versions prior to 19.4R3-S10; 20.1 version 20.1R3-S1 and later versions; 20.2 version 20.2R3-S2 and later versions prior to 20.2R3-S6; 20.3 version 20.3R3-S1 and later versions prior to 20.3R3-S6; 20.4 version 20.4R2-S2, 20.4R3 and later versions prior to 20.4R3-S5; 21.1 version 21.1R2 and later versions prior to 21.1R3-S4; 21.2 version 21.2R1-S1, 21.2R2 and later versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2; 22.3 versions prior to 22.3R1-S1, 22.3R2.

An Uncontrolled Resource Consumption vulnerability in the PFE management daemon (evo-pfemand) of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to cause an FPC crash leading to a Denial of Service (DoS). When a specific SNMP GET operation or a specific CLI command is executed this will cause a GUID resource leak, eventually leading to exhaustion and result in an FPC crash and reboot. GUID exhaustion will trigger a syslog message like one of the following for example: evo-pfemand[<pid>]: get_next_guid: Ran out of Guid Space ... evo-aftmand-zx[<pid>]: get_next_guid: Ran out of Guid Space ... This leak can be monitored by running the following command and taking note of the value in the rightmost column labeled Guids: user@host> show platform application-info allocations app evo-pfemand | match "IFDId|IFLId|Context" Node Application Context Name Live Allocs Fails Guids re0 evo-pfemand net::juniper::interfaces::IFDId 0 3448 0 3448 re0 evo-pfemand net::juniper::interfaces::IFLId 0 561 0 561 user@host> show platform application-info allocations app evo-pfemand | match "IFDId|IFLId|Context" Node Application Context Name Live Allocs Fails Guids re0 evo-pfemand net::juniper::interfaces::IFDId 0 3784 0 3784 re0 evo-pfemand net::juniper::interfaces::IFLId 0 647 0 647 This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R3-S3-EVO; 21.1-EVO version 21.1R1-EVO and later versions; 21.2-EVO versions prior to 21.2R3-S4-EVO; 21.3-EVO version 21.3R1-EVO and later versions; 21.4-EVO versions prior to 21.4R2-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in Routing Protocol Daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based, unauthenticated attacker to cause rpd to crash, leading to Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, when NETCONF and gRPC are enabled, and a specific query is executed via Dynamic Rendering (DREND), rpd will crash and restart. Continuous execution of this specific query will cause a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS * 22.2 versions earlier than 22.2R2-S2, 22.2R3; * 22.3 versions earlier than 22.3R2, 22.3R3. Juniper Networks Junos OS Evolved * 22.2 versions earlier than 22.2R2-S2-EVO, 22.2R3-EVO; * 22.3 versions earlier than 22.3R2-EVO, 22.3R3-EVO. This issue does not affect Juniper Networks: Junos OS versions earlier than 22.2R1; Junos OS Evolved versions earlier than 22.2R1-EVO.

An Improper Validation of Syntactic Correctness of Input vulnerability in Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On all Junos OS MX Series and SRX Series platforms, when SIP ALG is enabled, and a specific SIP packet is received and processed, NAT IP allocation fails for genuine traffic, which causes Denial of Service (DoS). Continuous receipt of this specific SIP ALG packet will cause a sustained DoS condition. NAT IP usage can be monitored by running the following command. user@srx> show security nat resource-usage source-pool <source_pool_name> Pool name: source_pool_name .. Address Factor-index Port-range Used Avail Total Usage X.X.X.X 0 Single Ports 50258 52342 62464 96% <<<<< - Alg Ports 0 2048 2048 0% This issue affects: Juniper Networks Junos OS on MX Series and SRX Series * All versions earlier than 21.2R3-S6; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2.

A NULL Pointer Dereference vulnerability in Juniper Networks Junos OS allows an attacker to send a specific packet causing the packet forwarding engine (PFE) to crash and restart, resulting in a Denial of Service (DoS). By continuously sending these specific packets, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue only affects Juniper Networks NFX Series, SRX Series platforms when SSL Proxy is configured. This issue affects Juniper Networks Junos OS on NFX Series and SRX Series: 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S1; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S2, 19.2R2; 19.3 versions prior to 19.3R2. This issue does not affect Juniper Networks Junos OS versions on NFX Series and SRX Series prior to 18.3R1.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX Series and NFX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). If an affected device receives specific valid traffic destined to the device, it will cause the PFE to crash and restart. Continued receipt and processing of this traffic will create a sustained DoS condition. This issue affects Junos OS on SRX Series: * 21.4 versions before 21.4R3-S7.9, * 22.1 versions before 22.1R3-S5.3, * 22.2 versions before 22.2R3-S4.11, * 22.3 versions before 22.3R3, * 22.4 versions before 22.4R3. This issue affects Junos OS on NFX Series: * 21.4 versions before 21.4R3-S8, * 22.1 versions after 22.1R1, * 22.2 versions before 22.2R3-S5, * 22.3 versions before 22.3R3, * 22.4 versions before 22.4R3. Junos OS versions prior to 21.4R1 are not affected by this issue.

An Improper Validation of Syntactic Correctness of Input vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). If a BGP update is received over an established BGP session which contains a tunnel encapsulation attribute with a specifically malformed TLV, rpd will crash and restart. This issue affects Juniper Networks Junos OS: * 20.4 versions 20.4R1 and later versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R3; * 23.2 versions earlier than 23.2R1-S2, 23.2R2; Junos OS Evolved: * 20.4-EVO versions 20.4R1-EVO and later versions earlier than 20.4R3-S9-EVO; * 21.2-EVO versions earlier than 21.2R3-S7-EVO; * 21.3-EVO versions earlier than 21.3R3-S5-EVO; * 21.4-EVO versions earlier than 21.4R3-S5-EVO; * 22.1-EVO versions earlier than 22.1R3-S4-EVO; * 22.2-EVO versions earlier than 22.2R3-S3-EVO; * 22.3-EVO versions earlier than 22.3R3-S1-EVO; * 22.4-EVO versions earlier than 22.4R3-EVO; * 23.2-EVO versions earlier than 23.2R1-S2-EVO, 23.2R2-EVO; This issue does not affect Juniper Networks * Junos OS versions earlier than 20.4R1; * Junos OS Evolved versions earlier than 20.4R1-EVO. This is a related but separate issue than the one described in JSA79095.

An Allocation of Resources Without Limits or Throttling vulnerability in the kernel of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). If a high rate of specific valid packets are processed by the routing engine (RE) this will lead to a loss of connectivity of the RE with other components of the chassis and thereby a complete and persistent system outage. Please note that a carefully designed lo0 firewall filter will block or limit these packets which should prevent this issue from occurring. The following log messages can be seen when this issue occurs: <host> kernel: nf_conntrack: nf_conntrack: table full, dropping packet This issue affects Juniper Networks Junos OS Evolved: * All versions earlier than 20.4R3-S7-EVO; * 21.2R1-EVO and later versions; * 21.4-EVO versions earlier than 21.4R3-S5-EVO; * 22.1-EVO versions earlier than 22.1R3-S2-EVO; * 22.2-EVO versions earlier than 22.2R3-EVO; * 22.3-EVO versions earlier than 22.3R2-EVO; * 22.4-EVO versions earlier than 22.4R2-EVO.

A Double Free vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on SRX Series allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). In a remote access VPN scenario, if a "tcp-encap-profile" is configured and a sequence of specific packets is received, a flowd crash and restart will be observed. This issue affects Juniper Networks Junos OS on SRX Series: * All versions earlier than 20.4R3-S8; * 21.2 versions earlier than 21.2R3-S6; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S3; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R2-S2, 22.4R3.

A NULL Pointer Dereference vulnerability in Juniper Networks Junos OS Evolved on ACX7024, ACX7100-32C and ACX7100-48L allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). If a specific IPv4 UDP packet is received and sent to the Routing Engine (RE) packetio crashes and restarts which causes a momentary traffic interruption. Continued receipt of such packets will lead to a sustained DoS. This issue does not happen with IPv6 packets. This issue affects Juniper Networks Junos OS Evolved on ACX7024, ACX7100-32C and ACX7100-48L: * 21.4-EVO versions earlier than 21.4R3-S6-EVO; * 22.1-EVO versions earlier than 22.1R3-S5-EVO; * 22.2-EVO versions earlier than 22.2R2-S1-EVO, 22.2R3-EVO; * 22.3-EVO versions earlier than 22.3R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions earlier than 21.4R1-EVO.

An Improper Handling of Syntactically Invalid Structure vulnerability in Object Flooding Protocol (OFP) service of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). On all Junos OS Evolved platforms, when specific TCP packets are received on an open OFP port, the OFP crashes leading to a restart of Routine Engine (RE). Continuous receipt of these specific TCP packets will lead to a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS Evolved * All versions earlier than 21.2R3-S7-EVO; * 21.3 versions earlier than 21.3R3-S5-EVO ; * 21.4 versions earlier than 21.4R3-S5-EVO; * 22.1 versions earlier than 22.1R3-S4-EVO; * 22.2 versions earlier than 22.2R3-S3-EVO ; * 22.3 versions earlier than 22.3R3-EVO; * 22.4 versions earlier than 22.4R2-EVO, 22.4R3-EVO.

An Improper Validation of Syntactic Correctness of Input vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). If an attacker sends high rate of specific ICMP traffic to a device with VXLAN configured, this causes a deadlock of the PFE and results in the device becoming unresponsive. A manual restart will be required to recover the device. This issue only affects EX4100, EX4400, EX4600, QFX5000 Series devices. This issue affects: Juniper Networks Junos OS * 21.4R3 versions earlier than 21.4R3-S4; * 22.1R3 versions earlier than 22.1R3-S3; * 22.2R2 versions earlier than 22.2R3-S1; * 22.3 versions earlier than 22.3R2-S2, 22.3R3; * 22.4 versions earlier than 22.4R2; * 23.1 versions earlier than 23.1R2.

Unspecified vulnerability in Oracle MySQL Server 5.5.39 and earlier, and 5.6.20 and earlier, allows remote attackers to affect availability via vectors related to CLIENT:SSL:yaSSL, a different vulnerability than CVE-2014-6494.

Unspecified vulnerability in Oracle MySQL Server 5.5.39 and earlier, and 5.6.20 and earlier, allows remote attackers to affect availability via vectors related to CLIENT:SSL:yaSSL, a different vulnerability than CVE-2014-6496.

Unspecified vulnerability in Oracle MySQL Server 5.5.38 and earlier, and 5.6.19 and earlier, allows remote attackers to affect availability via vectors related to SERVER:SSL:yaSSL.

The srxpfe process may crash on SRX Series services gateways when the UTM module processes a specific fragmented HTTP packet. The packet is misinterpreted as a regular TCP packet which causes the processor to crash. This issue affects all SRX Series platforms that support URL-Filtering and have web-filtering enabled. Affected releases are Juniper Networks Junos OS: 12.3X48 versions prior to 12.3X48-D85 on SRX Series; 15.1X49 versions prior to 15.1X49-D181, 15.1X49-D190 on SRX Series; 17.3 versions on SRX Series; 17.4 versions prior to 17.4R1-S8, 17.4R2-S5, 17.4R3 on SRX Series; 18.1 versions prior to 18.1R3-S6 on SRX Series; 18.2 versions prior to 18.2R2-S1, 18.2R3 on SRX Series; 18.3 versions prior to 18.3R1-S2, 18.3R2 on SRX Series; 18.4 versions prior to 18.4R1-S1, 18.4R2 on SRX Series.

Juniper Junos 10.0 before 10.0S28, 10.4 before 10.4R7, 11.1 before 11.1R5, 11.2 before 11.2R2, and 11.4 before 11.4R1, when in a Next-Generation Multicast VPN (NGEN MVPN) environment, allows remote attackers to cause a denial of service (RPD routing daemon crash) via a large number of crafted PIM (S,G) join requests.

Juniper Junos before 10.4S14, 11.4 before 11.4R5-S2, 12.1R before 12.1R3, 12.1X44 before 12.1X44-D20, and 12.1X45 before 12.1X45-D15 on SRX Series services gateways, when a plugin using TCP proxy is configured, allows remote attackers to cause a denial of service (flow daemon crash) via an unspecified sequence of TCP packets.

An Improper Validation of Specified Type of Input vulnerability in the packet forwarding engine (pfe) Juniper Networks Junos OS on SRX5000 Series allows an unauthenticated, network based attacker to cause a Denial of Service (Dos). When a non-clustered SRX5000 device receives a specifically malformed packet this will cause a flowd crash and restart. This issue affects Junos OS: * 22.1 releases 22.1R1 and later before 22.2R3-S5, * 22.3 releases before 22.3R3-S4, * 22.4 releases before 22.4R3-S4, * 23.2 releases before 23.2R2-S2, * 23.4 releases before 23.4R2-S1, * 24.2 releases before 24.2R1-S1, 24.2R2. Please note that the PR does indicate that earlier versions have been fixed as well, but these won't be adversely impacted by this.

An Allocation of Resources Without Limits or Throttling vulnerability in the kernel of Juniper Networks Junos OS Evolved allows an unauthenticated, network based attacker to cause a Denial of Service (DoS). In specific cases the state of TCP sessions that are terminated is not cleared, which over time leads to an exhaustion of resources, preventing new connections to the control plane from being established. A continuously increasing number of connections shown by: user@host > show system connections is indicative of the problem. To recover the respective RE needs to be restarted manually. This issue only affects IPv4 but does not affect IPv6. This issue only affects TCP sessions established in-band (over an interface on an FPC) but not out-of-band (over the management ethernet port on the routing-engine). This issue affects Junos OS Evolved:  * All versions before 21.4R3-S9-EVO, * 22.2 versions before 22.2R3-S4-EVO, * 22.4 version before 22.4R3-S3-EVO, * 23.2 versions before 23.2R2-S1-EVO, * 23.4 versions before 23.4R2-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the routing protocol daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network based attacker to cause a Denial of Service (DoS).  In a scenario where BGP Monitoring Protocol (BMP) is configured with rib-in pre-policy monitoring, receiving a BGP update with a specifically malformed AS PATH attribute over an established BGP session, can cause an RPD crash and restart. This issue affects: Junos OS:  * All versions before 21.2R3-S8, * 21.4 versions before 21.4R3-S8, * 22.2 versions before 22.2R3-S4, * 22.3 versions before 22.3R3-S3, * 22.4 versions before 22.4R3-S2, * 23.2 versions before 23.2R2-S1, * 23.4 versions before 23.4R1-S2, 23.4R2; Junos OS Evolved: * All versions before 21.2R3-S8-EVO, * 21.4 versions before 21.4R3-S8-EVO, * 22.2 versions before 22.2R3-S4-EVO, * 22.3 versions before 22.3R3-S3-EVO, * 22.4 versions before 22.4R3-S2-EVO, * 23.2 versions before 23.2R2-S1-EVO, * 23.4 versions before 23.4R1-S2-EVO, 23.4R2-EVO.

On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific BGP packet can lead to a routing process daemon (RPD) crash and restart. This issue can occur even before the BGP session with the peer is established. Repeated receipt of this specific BGP packet can result in an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 18.2X75 versions starting from 18.2X75-D50.8, 18.2X75-D60 and later versions, prior to 18.2X75-D52.8, 18.2X75-D53, 18.2X75-D60.2, 18.2X75-D65.1, 18.2X75-D70; 19.4 versions 19.4R1 and 19.4R1-S1; 20.1 versions prior to 20.1R1-S2, 20.1R2. Juniper Networks Junos OS Evolved: 19.4-EVO versions prior to 19.4R2-S2-EVO; 20.1-EVO versions prior to 20.1R2-EVO. This issue does not affect: Juniper Networks Junos OS releases prior to 19.4R1. Juniper Networks Junos OS Evolved releases prior to 19.4R1-EVO.

When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of small fragments requiring reassembly, generating the following error messages: [LOG: Err] MQSS(2): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[2:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(2): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1960, QID 0 [LOG: Err] MQSS(2): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0xc38fb1 [LOG: Notice] Error: /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(2), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S9, 17.4R3-S1 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D34, 18.2X75-D41, 18.2X75-D53, 18.2X75-D65, 18.2X75-D430 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S2 on MX Series; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.

Receipt of a specific MPLS or IPv6 packet on the core facing interface of an MX Series device configured for Broadband Edge (BBE) service may trigger a kernel crash (vmcore), causing the device to reboot. The issue is specific to the processing of packets destined to BBE clients connected to MX Series subscriber management platforms. This issue affects MX Series running Juniper Networks Junos OS: 17.2 versions starting from17.2R2-S6, 17.2R3 and later releases, prior to 17.2R3-S3; 17.3 versions starting from 17.3R2-S4, 17.3R3-S2 and later releases, prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions starting from 17.4R2 and later releases, prior to 17.4R2-S7,17.4R3; 18.1 versions starting from 18.1R2-S3, 18.1R3 and later releases, prior to 18.1R3-S6; 18.2 versions starting from18.2R1-S1, 18.2R2 and later releases, prior to 18.2R3-S2; 18.2X75 versions prior to 18.2X75-D51, 18.2X75-D60; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S2, 19.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R2-S6.

An Improper Handling of Length Parameter Inconsistency vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network based, unauthenticated attacker to cause an RPD crash leading to a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Upon receipt of a malformed BGP flowspec update, RPD will crash resulting in a Denial of Service. This issue affects Juniper Networks Junos OS: All versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S1, 20.3R2; Juniper Networks Junos OS Evolved: All versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R2-EVO; 20.3 versions prior to 20.3R2-EVO;

This is a similar, but different vulnerability than the issue reported as CVE-2024-39549. A double-free vulnerability in the routing process daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an attacker to send a malformed BGP Path attribute update which allocates memory used to log the bad path attribute. This double free of memory is causing an rpd crash, leading to a Denial of Service (DoS). This issue affects: Junos OS:  * from 22.4 before 22.4R3-S4. Junos OS Evolved: * from 22.4 before 22.4R3-S4-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the the IKE daemon (iked) of Juniper Networks Junos OS on SRX Series, MX Series with SPC3 and NFX350 allows allows an unauthenticated, network-based attacker sending specific mismatching parameters as part of the IPsec negotiation to trigger an iked crash leading to Denial of Service (DoS). This issue is applicable to all platforms that run iked. This issue affects Junos OS on SRX Series, MX Series with SPC3 and NFX350:  * All versions before 21.2R3-S8,  * from 21.4 before 21.4R3-S7,  * from 22.1 before 22.1R3-S2,  * from 22.2 before 22.2R3-S1,  * from 22.3 before 22.3R2-S1, 22.3R3,  * from 22.4 before 22.4R1-S2, 22.4R2, 22.4R3.

A Heap-based Buffer Overflow vulnerability in the telemetry sensor process (sensord) of Juniper Networks Junos OS on MX240, MX480, MX960 platforms using MPC10E causes a steady increase in memory utilization, ultimately leading to a Denial of Service (DoS). When the device is subscribed to a specific subscription on Junos Telemetry Interface, a slow memory leak occurs and eventually all resources are consumed and the device becomes unresponsive. A manual reboot of the Line Card will be required to restore the device to its normal functioning.  This issue is only seen when telemetry subscription is active. The Heap memory utilization can be monitored using the following command:   > show system processes extensive The following command can be used to monitor the memory utilization of the specific sensor   > show system info | match sensord PID NAME MEMORY PEAK MEMORY %CPU THREAD-COUNT CORE-AFFINITY UPTIME 1986 sensord 877.57MB 877.57MB 2 4 0,2-15 7-21:41:32 This issue affects Junos OS:  * from 21.2R3-S5 before 21.2R3-S7,  * from 21.4R3-S4 before 21.4R3-S6,  * from 22.2R3 before 22.2R3-S4,  * from 22.3R2 before 22.3R3-S2,  * from 22.4R1 before 22.4R3,  * from 23.2R1 before 23.2R2.

An Improper Handling of Exceptional Conditions vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker sending a specific BGP packet to cause rpd to crash and restart, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects systems with BGP traceoptions enabled and requires a BGP session to be already established.  Systems without BGP traceoptions enabled are not affected by this issue. This issue affects iBGP and eBGP, and both IPv4 and IPv6 are affected by this vulnerability. This issue affects: Junos OS:  * All versions before 21.2R3-S8,  * from 21.4 before 21.4R3-S8,  * from 22.2 before 22.2R3-S4,  * from 22.3 before 22.3R3-S4, * from 22.4 before 22.4R3-S3,  * from 23.2 before 23.2R2-S1,  * from 23.4 before 23.4R2;  Junos OS Evolved:  * All versions before 21.2R3-S8-EVO,  * from 21.4-EVO before 21.4R3-S8-EVO,  * from 22.2-EVO before 22.2R3-S4-EVO,  * from 22.3-EVO before 22.3R3-S4-EVO, * from 22.4-EVO before 22.4R3-S3-EVO,  * from 23.2-EVO before 23.2R2-S1-EVO,  * from 23.4-EVO before 23.4R2-EVO.

An Out-of-Bounds Read vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker sending a specifically malformed BGP packet to cause rpd to crash and restart, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects systems configured in either of two ways: * systems with BGP traceoptions enabled * systems with BGP traffic engineering configured This issue can affect iBGP and eBGP with any address family configured. The specific attribute involved is non-transitive, and will not propagate across a network. This issue affects: Junos OS:  * All versions before 21.4R3-S8, * 22.2 before 22.2R3-S5,  * 22.3 before 22.3R3-S4,  * 22.4 before 22.4R3-S3,  * 23.2 before 23.2R2-S2,  * 23.4 before 23.4R2;  Junos OS Evolved:  * All versions before 21.4R3-S8-EVO,  * 22.2-EVO before 22.2R3-S5-EVO,  * 22.3-EVO before 22.3R3-S4-EVO,  * 22.4-EVO before 22.4R3-S3-EVO,  * 23.2-EVO before 23.2R2-S2-EVO,  * 23.4-EVO before 23.4R2-EVO.