In the Linux kernel, the following vulnerability has been resolved: KVM: nSVM: Ignore nCR3[4:0] when loading PDPTEs from memory Ignore nCR3[4:0] when loading PDPTEs from memory for nested SVM, as bits 4:0 of CR3 are ignored when PAE paging is used, and thus VMRUN doesn't enforce 32-byte alignment of nCR3. In the absolute worst case scenario, failure to ignore bits 4:0 can result in an out-of-bounds read, e.g. if the target page is at the end of a memslot, and the VMM isn't using guard pages. Per the APM: The CR3 register points to the base address of the page-directory-pointer table. The page-directory-pointer table is aligned on a 32-byte boundary, with the low 5 address bits 4:0 assumed to be 0. And the SDM's much more explicit: 4:0 Ignored Note, KVM gets this right when loading PDPTRs, it's only the nSVM flow that is broken.
In the Linux kernel, the following vulnerability has been resolved: iio: health: afe4403: Fix oob read in afe4403_read_raw KASAN report out-of-bounds read as follows: BUG: KASAN: global-out-of-bounds in afe4403_read_raw+0x42e/0x4c0 Read of size 4 at addr ffffffffc02ac638 by task cat/279 Call Trace: afe4403_read_raw iio_read_channel_info dev_attr_show The buggy address belongs to the variable: afe4403_channel_leds+0x18/0xffffffffffffe9e0 This issue can be reproduced by singe command: $ cat /sys/bus/spi/devices/spi0.0/iio\:device0/in_intensity6_raw The array size of afe4403_channel_leds is less than channels, so access with chan->address cause OOB read in afe4403_read_raw. Fix it by moving access before use it.
In the Linux kernel, the following vulnerability has been resolved: ice: ensure the copied buf is NUL terminated Currently, we allocate a count-sized kernel buffer and copy count bytes from userspace to that buffer. Later, we use sscanf on this buffer but we don't ensure that the string is terminated inside the buffer, this can lead to OOB read when using sscanf. Fix this issue by using memdup_user_nul instead of memdup_user.
In the Linux kernel, the following vulnerability has been resolved: ipv4: Handle attempt to delete multipath route when fib_info contains an nh reference Gwangun Jung reported a slab-out-of-bounds access in fib_nh_match: fib_nh_match+0xf98/0x1130 linux-6.0-rc7/net/ipv4/fib_semantics.c:961 fib_table_delete+0x5f3/0xa40 linux-6.0-rc7/net/ipv4/fib_trie.c:1753 inet_rtm_delroute+0x2b3/0x380 linux-6.0-rc7/net/ipv4/fib_frontend.c:874 Separate nexthop objects are mutually exclusive with the legacy multipath spec. Fix fib_nh_match to return if the config for the to be deleted route contains a multipath spec while the fib_info is using a nexthop object.
In the Linux kernel, the following vulnerability has been resolved: net: mvneta: Prevent out of bounds read in mvneta_config_rss() The pp->indir[0] value comes from the user. It is passed to: if (cpu_online(pp->rxq_def)) inside the mvneta_percpu_elect() function. It needs bounds checkeding to ensure that it is not beyond the end of the cpu bitmap.
In the Linux kernel, the following vulnerability has been resolved: iio: health: afe4404: Fix oob read in afe4404_[read|write]_raw KASAN report out-of-bounds read as follows: BUG: KASAN: global-out-of-bounds in afe4404_read_raw+0x2ce/0x380 Read of size 4 at addr ffffffffc00e4658 by task cat/278 Call Trace: afe4404_read_raw iio_read_channel_info dev_attr_show The buggy address belongs to the variable: afe4404_channel_leds+0x18/0xffffffffffffe9c0 This issue can be reproduce by singe command: $ cat /sys/bus/i2c/devices/0-0058/iio\:device0/in_intensity6_raw The array size of afe4404_channel_leds and afe4404_channel_offdacs are less than channels, so access with chan->address cause OOB read in afe4404_[read|write]_raw. Fix it by moving access before use them.
In the Linux kernel, the following vulnerability has been resolved: powerpc/xive/spapr: correct bitmap allocation size kasan detects access beyond the end of the xibm->bitmap allocation: BUG: KASAN: slab-out-of-bounds in _find_first_zero_bit+0x40/0x140 Read of size 8 at addr c00000001d1d0118 by task swapper/0/1 CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.19.0-rc2-00001-g90df023b36dd #28 Call Trace: [c00000001d98f770] [c0000000012baab8] dump_stack_lvl+0xac/0x108 (unreliable) [c00000001d98f7b0] [c00000000068faac] print_report+0x37c/0x710 [c00000001d98f880] [c0000000006902c0] kasan_report+0x110/0x354 [c00000001d98f950] [c000000000692324] __asan_load8+0xa4/0xe0 [c00000001d98f970] [c0000000011c6ed0] _find_first_zero_bit+0x40/0x140 [c00000001d98f9b0] [c0000000000dbfbc] xive_spapr_get_ipi+0xcc/0x260 [c00000001d98fa70] [c0000000000d6d28] xive_setup_cpu_ipi+0x1e8/0x450 [c00000001d98fb30] [c000000004032a20] pSeries_smp_probe+0x5c/0x118 [c00000001d98fb60] [c000000004018b44] smp_prepare_cpus+0x944/0x9ac [c00000001d98fc90] [c000000004009f9c] kernel_init_freeable+0x2d4/0x640 [c00000001d98fd90] [c0000000000131e8] kernel_init+0x28/0x1d0 [c00000001d98fe10] [c00000000000cd54] ret_from_kernel_thread+0x5c/0x64 Allocated by task 0: kasan_save_stack+0x34/0x70 __kasan_kmalloc+0xb4/0xf0 __kmalloc+0x268/0x540 xive_spapr_init+0x4d0/0x77c pseries_init_irq+0x40/0x27c init_IRQ+0x44/0x84 start_kernel+0x2a4/0x538 start_here_common+0x1c/0x20 The buggy address belongs to the object at c00000001d1d0118 which belongs to the cache kmalloc-8 of size 8 The buggy address is located 0 bytes inside of 8-byte region [c00000001d1d0118, c00000001d1d0120) The buggy address belongs to the physical page: page:c00c000000074740 refcount:1 mapcount:0 mapping:0000000000000000 index:0xc00000001d1d0558 pfn:0x1d1d flags: 0x7ffff000000200(slab|node=0|zone=0|lastcpupid=0x7ffff) raw: 007ffff000000200 c00000001d0003c8 c00000001d0003c8 c00000001d010480 raw: c00000001d1d0558 0000000001e1000a 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: c00000001d1d0000: fc 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc c00000001d1d0080: fc fc 00 fc fc fc fc fc fc fc fc fc fc fc fc fc >c00000001d1d0100: fc fc fc 02 fc fc fc fc fc fc fc fc fc fc fc fc ^ c00000001d1d0180: fc fc fc fc 04 fc fc fc fc fc fc fc fc fc fc fc c00000001d1d0200: fc fc fc fc fc 04 fc fc fc fc fc fc fc fc fc fc This happens because the allocation uses the wrong unit (bits) when it should pass (BITS_TO_LONGS(count) * sizeof(long)) or equivalent. With small numbers of bits, the allocated object can be smaller than sizeof(long), which results in invalid accesses. Use bitmap_zalloc() to allocate and initialize the irq bitmap, paired with bitmap_free() for consistency.
In the Linux kernel, the following vulnerability has been resolved: net: ethernet: mtk_eth_soc: out of bounds read in mtk_hwlro_get_fdir_entry() The "fsp->location" variable comes from user via ethtool_get_rxnfc(). Check that it is valid to prevent an out of bounds read.
In the Linux kernel, the following vulnerability has been resolved: usb: isp1760: Fix out-of-bounds array access Running the driver through kasan gives an interesting splat: BUG: KASAN: global-out-of-bounds in isp1760_register+0x180/0x70c Read of size 20 at addr f1db2e64 by task swapper/0/1 (...) isp1760_register from isp1760_plat_probe+0x1d8/0x220 (...) This happens because the loop reading the regmap fields for the different ISP1760 variants look like this: for (i = 0; i < HC_FIELD_MAX; i++) { ... } Meaning it expects the arrays to be at least HC_FIELD_MAX - 1 long. However the arrays isp1760_hc_reg_fields[], isp1763_hc_reg_fields[], isp1763_hc_volatile_ranges[] and isp1763_dc_volatile_ranges[] are dynamically sized during compilation. Fix this by putting an empty assignment to the [HC_FIELD_MAX] and [DC_FIELD_MAX] array member at the end of each array. This will make the array one member longer than it needs to be, but avoids the risk of overwriting whatever is inside [HC_FIELD_MAX - 1] and is simple and intuitive to read. Also add comments explaining what is going on.
In the Linux kernel, the following vulnerability has been resolved: wifi: nl80211: fix NL80211_ATTR_MLO_LINK_ID off-by-one Since the netlink attribute range validation provides inclusive checking, the *max* of attribute NL80211_ATTR_MLO_LINK_ID should be IEEE80211_MLD_MAX_NUM_LINKS - 1 otherwise causing an off-by-one. One crash stack for demonstration: ================================================================== BUG: KASAN: wild-memory-access in ieee80211_tx_control_port+0x3b6/0xca0 net/mac80211/tx.c:5939 Read of size 6 at addr 001102080000000c by task fuzzer.386/9508 CPU: 1 PID: 9508 Comm: syz.1.386 Not tainted 6.1.70 #2 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x177/0x231 lib/dump_stack.c:106 print_report+0xe0/0x750 mm/kasan/report.c:398 kasan_report+0x139/0x170 mm/kasan/report.c:495 kasan_check_range+0x287/0x290 mm/kasan/generic.c:189 memcpy+0x25/0x60 mm/kasan/shadow.c:65 ieee80211_tx_control_port+0x3b6/0xca0 net/mac80211/tx.c:5939 rdev_tx_control_port net/wireless/rdev-ops.h:761 [inline] nl80211_tx_control_port+0x7b3/0xc40 net/wireless/nl80211.c:15453 genl_family_rcv_msg_doit+0x22e/0x320 net/netlink/genetlink.c:756 genl_family_rcv_msg net/netlink/genetlink.c:833 [inline] genl_rcv_msg+0x539/0x740 net/netlink/genetlink.c:850 netlink_rcv_skb+0x1de/0x420 net/netlink/af_netlink.c:2508 genl_rcv+0x24/0x40 net/netlink/genetlink.c:861 netlink_unicast_kernel net/netlink/af_netlink.c:1326 [inline] netlink_unicast+0x74b/0x8c0 net/netlink/af_netlink.c:1352 netlink_sendmsg+0x882/0xb90 net/netlink/af_netlink.c:1874 sock_sendmsg_nosec net/socket.c:716 [inline] __sock_sendmsg net/socket.c:728 [inline] ____sys_sendmsg+0x5cc/0x8f0 net/socket.c:2499 ___sys_sendmsg+0x21c/0x290 net/socket.c:2553 __sys_sendmsg net/socket.c:2582 [inline] __do_sys_sendmsg net/socket.c:2591 [inline] __se_sys_sendmsg+0x19e/0x270 net/socket.c:2589 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x45/0x90 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x63/0xcd Update the policy to ensure correct validation.
A use-after-free flaw was found in vhost_net_set_backend in drivers/vhost/net.c in virtio network subcomponent in the Linux kernel due to a double fget. This flaw could allow a local attacker to crash the system, and could even lead to a kernel information leak problem.
In the Linux kernel, the following vulnerability has been resolved: phy: stm32: fix a refcount leak in stm32_usbphyc_pll_enable() This error path needs to decrement "usbphyc->n_pll_cons.counter" before returning.
In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Check the count value of channel spec to prevent out-of-bounds reads This patch fixes slab-out-of-bounds reads in brcmfmac that occur in brcmf_construct_chaninfo() and brcmf_enable_bw40_2g() when the count value of channel specifications provided by the device is greater than the length of 'list->element[]', decided by the size of the 'list' allocated with kzalloc(). The patch adds checks that make the functions free the buffer and return -EINVAL if that is the case. Note that the negative return is handled by the caller, brcmf_setup_wiphybands() or brcmf_cfg80211_attach(). Found by a modified version of syzkaller. Crash Report from brcmf_construct_chaninfo(): ================================================================== BUG: KASAN: slab-out-of-bounds in brcmf_setup_wiphybands+0x1238/0x1430 Read of size 4 at addr ffff888115f24600 by task kworker/0:2/1896 CPU: 0 PID: 1896 Comm: kworker/0:2 Tainted: G W O 5.14.0+ #132 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Workqueue: usb_hub_wq hub_event Call Trace: dump_stack_lvl+0x57/0x7d print_address_description.constprop.0.cold+0x93/0x334 kasan_report.cold+0x83/0xdf brcmf_setup_wiphybands+0x1238/0x1430 brcmf_cfg80211_attach+0x2118/0x3fd0 brcmf_attach+0x389/0xd40 brcmf_usb_probe+0x12de/0x1690 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_set_configuration+0x984/0x1770 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_new_device.cold+0x463/0xf66 hub_event+0x10d5/0x3330 process_one_work+0x873/0x13e0 worker_thread+0x8b/0xd10 kthread+0x379/0x450 ret_from_fork+0x1f/0x30 Allocated by task 1896: kasan_save_stack+0x1b/0x40 __kasan_kmalloc+0x7c/0x90 kmem_cache_alloc_trace+0x19e/0x330 brcmf_setup_wiphybands+0x290/0x1430 brcmf_cfg80211_attach+0x2118/0x3fd0 brcmf_attach+0x389/0xd40 brcmf_usb_probe+0x12de/0x1690 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_set_configuration+0x984/0x1770 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_new_device.cold+0x463/0xf66 hub_event+0x10d5/0x3330 process_one_work+0x873/0x13e0 worker_thread+0x8b/0xd10 kthread+0x379/0x450 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff888115f24000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 1536 bytes inside of 2048-byte region [ffff888115f24000, ffff888115f24800) Memory state around the buggy address: ffff888115f24500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888115f24580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff888115f24600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff888115f24680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888115f24700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ================================================================== Crash Report from brcmf_enable_bw40_2g(): ========== ---truncated---
In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Fix an out-of-bounds bug in __snd_usb_parse_audio_interface() There may be a bad USB audio device with a USB ID of (0x04fa, 0x4201) and the number of it's interfaces less than 4, an out-of-bounds read bug occurs when parsing the interface descriptor for this device. Fix this by checking the number of interfaces.
NVIDIA GPU Display Driver for Linux contains a vulnerability in the kernel mode layer handler, where an Integer overflow may lead to denial of service or information disclosure.
A flaw was found in the Linux kernel. A NULL pointer dereference may occur while a slip driver is in progress to detach in sl_tx_timeout in drivers/net/slip/slip.c. This issue could allow an attacker to crash the system or leak internal kernel information.
In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix mmhub client id out-of-bounds access Properly handle cid 0x140.
An issue was discovered in the Linux kernel before 6.2. The ntfs3 subsystem does not properly check for correctness during disk reads, leading to an out-of-bounds read in ntfs_set_ea in fs/ntfs3/xattr.c.
An Out-of-Bounds Read was discovered in arch/arm/mach-footbridge/personal-pci.c in the Linux kernel through 5.12.11 because of the lack of a check for a value that shouldn't be negative, e.g., access to element -2 of an array, aka CID-298a58e165e4.
In the Linux kernel, the following vulnerability has been resolved: ksmbd: validate mech token in session setup If client send invalid mech token in session setup request, ksmbd validate and make the error if it is invalid.
In the Linux kernel, the following vulnerability has been resolved: vlan: enforce underlying device type Currently, VLAN devices can be created on top of non-ethernet devices. Besides the fact that it doesn't make much sense, this also causes a bug which leaks the address of a kernel function to usermode. When creating a VLAN device, we initialize GARP (garp_init_applicant) and MRP (mrp_init_applicant) for the underlying device. As part of the initialization process, we add the multicast address of each applicant to the underlying device, by calling dev_mc_add. __dev_mc_add uses dev->addr_len to determine the length of the new multicast address. This causes an out-of-bounds read if dev->addr_len is greater than 6, since the multicast addresses provided by GARP and MRP are only 6 bytes long. This behaviour can be reproduced using the following commands: ip tunnel add gretest mode ip6gre local ::1 remote ::2 dev lo ip l set up dev gretest ip link add link gretest name vlantest type vlan id 100 Then, the following command will display the address of garp_pdu_rcv: ip maddr show | grep 01:80:c2:00:00:21 Fix the bug by enforcing the type of the underlying device during VLAN device initialization.
In the Linux kernel, the following vulnerability has been resolved: ASoC: hdmi-codec: Fix OOB memory accesses Correct size of iec_status array by changing it to the size of status array of the struct snd_aes_iec958. This fixes out-of-bounds slab read accesses made by memcpy() of the hdmi-codec driver. This problem is reported by KASAN.
In the Linux kernel, the following vulnerability has been resolved: usbnet: ipheth: fix possible overflow in DPE length check Originally, it was possible for the DPE length check to overflow if wDatagramIndex + wDatagramLength > U16_MAX. This could lead to an OoB read. Move the wDatagramIndex term to the other side of the inequality. An existing condition ensures that wDatagramIndex < urb->actual_length.
In the Linux kernel, the following vulnerability has been resolved: orangefs: fix a oob in orangefs_debug_write I got a syzbot report: slab-out-of-bounds Read in orangefs_debug_write... several people suggested fixes, I tested Al Viro's suggestion and made this patch.
In the Linux kernel, the following vulnerability has been resolved: usbnet: ipheth: use static NDP16 location in URB Original code allowed for the start of NDP16 to be anywhere within the URB based on the `wNdpIndex` value in NTH16. Only the start position of NDP16 was checked, so it was possible for even the fixed-length part of NDP16 to extend past the end of URB, leading to an out-of-bounds read. On iOS devices, the NDP16 header always directly follows NTH16. Rely on and check for this specific format. This, along with NCM-specific minimal URB length check that already exists, will ensure that the fixed-length part of NDP16 plus a set amount of DPEs fit within the URB. Note that this commit alone does not fully address the OoB read. The limit on the amount of DPEs needs to be enforced separately.
In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: limit printed string from FW file There's no guarantee here that the file is always with a NUL-termination, so reading the string may read beyond the end of the TLV. If that's the last TLV in the file, it can perhaps even read beyond the end of the file buffer. Fix that by limiting the print format to the size of the buffer we have.
In the Linux kernel, the following vulnerability has been resolved: usbnet: ipheth: fix DPE OoB read Fix an out-of-bounds DPE read, limit the number of processed DPEs to the amount that fits into the fixed-size NDP16 header.
In the Linux kernel, the following vulnerability has been resolved: ksmbd: validate zero num_subauth before sub_auth is accessed Access psid->sub_auth[psid->num_subauth - 1] without checking if num_subauth is non-zero leads to an out-of-bounds read. This patch adds a validation step to ensure num_subauth != 0 before sub_auth is accessed.
An issue was discovered in the Linux kernel through 5.11.3. drivers/scsi/scsi_transport_iscsi.c is adversely affected by the ability of an unprivileged user to craft Netlink messages.
In the Linux kernel, the following vulnerability has been resolved: iio: adc: rockchip_saradc: fix information leak in triggered buffer The 'data' local struct is used to push data to user space from a triggered buffer, but it does not set values for inactive channels, as it only uses iio_for_each_active_channel() to assign new values. Initialize the struct to zero before using it to avoid pushing uninitialized information to userspace.
In the Linux kernel, the following vulnerability has been resolved: iio: adc: ti-ads1119: fix information leak in triggered buffer The 'scan' local struct is used to push data to user space from a triggered buffer, but it has a hole between the sample (unsigned int) and the timestamp. This hole is never initialized. Initialize the struct to zero before using it to avoid pushing uninitialized information to userspace.
In the Linux kernel, the following vulnerability has been resolved: iio: adc: ti-ads8688: fix information leak in triggered buffer The 'buffer' local array is used to push data to user space from a triggered buffer, but it does not set values for inactive channels, as it only uses iio_for_each_active_channel() to assign new values. Initialize the array to zero before using it to avoid pushing uninitialized information to userspace.
In the Linux kernel, the following vulnerability has been resolved: soc: qcom: socinfo: Avoid out of bounds read of serial number On MSM8916 devices, the serial number exposed in sysfs is constant and does not change across individual devices. It's always: db410c:/sys/devices/soc0$ cat serial_number 2644893864 The firmware used on MSM8916 exposes SOCINFO_VERSION(0, 8), which does not have support for the serial_num field in the socinfo struct. There is an existing check to avoid exposing the serial number in that case, but it's not correct: When checking the item_size returned by SMEM, we need to make sure the *end* of the serial_num is within bounds, instead of comparing with the *start* offset. The serial_number currently exposed on MSM8916 devices is just an out of bounds read of whatever comes after the socinfo struct in SMEM. Fix this by changing offsetof() to offsetofend(), so that the size of the field is also taken into account.
In the Linux kernel, the following vulnerability has been resolved: iio: light: bh1745: fix information leak in triggered buffer The 'scan' local struct is used to push data to user space from a triggered buffer, but it does not set values for inactive channels, as it only uses iio_for_each_active_channel() to assign new values. Initialize the struct to zero before using it to avoid pushing uninitialized information to userspace.
In the Linux kernel, the following vulnerability has been resolved: netfilter: x_tables: fix LED ID check in led_tg_check() Syzbot has reported the following BUG detected by KASAN: BUG: KASAN: slab-out-of-bounds in strlen+0x58/0x70 Read of size 1 at addr ffff8881022da0c8 by task repro/5879 ... Call Trace: <TASK> dump_stack_lvl+0x241/0x360 ? __pfx_dump_stack_lvl+0x10/0x10 ? __pfx__printk+0x10/0x10 ? _printk+0xd5/0x120 ? __virt_addr_valid+0x183/0x530 ? __virt_addr_valid+0x183/0x530 print_report+0x169/0x550 ? __virt_addr_valid+0x183/0x530 ? __virt_addr_valid+0x183/0x530 ? __virt_addr_valid+0x45f/0x530 ? __phys_addr+0xba/0x170 ? strlen+0x58/0x70 kasan_report+0x143/0x180 ? strlen+0x58/0x70 strlen+0x58/0x70 kstrdup+0x20/0x80 led_tg_check+0x18b/0x3c0 xt_check_target+0x3bb/0xa40 ? __pfx_xt_check_target+0x10/0x10 ? stack_depot_save_flags+0x6e4/0x830 ? nft_target_init+0x174/0xc30 nft_target_init+0x82d/0xc30 ? __pfx_nft_target_init+0x10/0x10 ? nf_tables_newrule+0x1609/0x2980 ? nf_tables_newrule+0x1609/0x2980 ? rcu_is_watching+0x15/0xb0 ? nf_tables_newrule+0x1609/0x2980 ? nf_tables_newrule+0x1609/0x2980 ? __kmalloc_noprof+0x21a/0x400 nf_tables_newrule+0x1860/0x2980 ? __pfx_nf_tables_newrule+0x10/0x10 ? __nla_parse+0x40/0x60 nfnetlink_rcv+0x14e5/0x2ab0 ? __pfx_validate_chain+0x10/0x10 ? __pfx_nfnetlink_rcv+0x10/0x10 ? __lock_acquire+0x1384/0x2050 ? netlink_deliver_tap+0x2e/0x1b0 ? __pfx_lock_release+0x10/0x10 ? netlink_deliver_tap+0x2e/0x1b0 netlink_unicast+0x7f8/0x990 ? __pfx_netlink_unicast+0x10/0x10 ? __virt_addr_valid+0x183/0x530 ? __check_object_size+0x48e/0x900 netlink_sendmsg+0x8e4/0xcb0 ? __pfx_netlink_sendmsg+0x10/0x10 ? aa_sock_msg_perm+0x91/0x160 ? __pfx_netlink_sendmsg+0x10/0x10 __sock_sendmsg+0x223/0x270 ____sys_sendmsg+0x52a/0x7e0 ? __pfx_____sys_sendmsg+0x10/0x10 __sys_sendmsg+0x292/0x380 ? __pfx___sys_sendmsg+0x10/0x10 ? lockdep_hardirqs_on_prepare+0x43d/0x780 ? __pfx_lockdep_hardirqs_on_prepare+0x10/0x10 ? exc_page_fault+0x590/0x8c0 ? do_syscall_64+0xb6/0x230 do_syscall_64+0xf3/0x230 entry_SYSCALL_64_after_hwframe+0x77/0x7f ... </TASK> Since an invalid (without '\0' byte at all) byte sequence may be passed from userspace, add an extra check to ensure that such a sequence is rejected as possible ID and so never passed to 'kstrdup()' and further.
In the Linux kernel, the following vulnerability has been resolved: x86/CPU/AMD: Terminate the erratum_1386_microcode array The erratum_1386_microcode array requires an empty entry at the end. Otherwise x86_match_cpu_with_stepping() will continue iterate the array after it ended. Add an empty entry to erratum_1386_microcode to its end.
In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix Out-of-Bounds Read in ksmbd_vfs_stream_read An offset from client could be a negative value, It could lead to an out-of-bounds read from the stream_buf. Note that this issue is coming when setting 'vfs objects = streams_xattr parameter' in ksmbd.conf.
In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Adjust VSDB parser for replay feature At some point, the IEEE ID identification for the replay check in the AMD EDID was added. However, this check causes the following out-of-bounds issues when using KASAN: [ 27.804016] BUG: KASAN: slab-out-of-bounds in amdgpu_dm_update_freesync_caps+0xefa/0x17a0 [amdgpu] [ 27.804788] Read of size 1 at addr ffff8881647fdb00 by task systemd-udevd/383 ... [ 27.821207] Memory state around the buggy address: [ 27.821215] ffff8881647fda00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 27.821224] ffff8881647fda80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 27.821234] >ffff8881647fdb00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 27.821243] ^ [ 27.821250] ffff8881647fdb80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 27.821259] ffff8881647fdc00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 27.821268] ================================================================== This is caused because the ID extraction happens outside of the range of the edid lenght. This commit addresses this issue by considering the amd_vsdb_block size. (cherry picked from commit b7e381b1ccd5e778e3d9c44c669ad38439a861d8)
In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Fix out of bounds reads when finding clock sources The current USB-audio driver code doesn't check bLength of each descriptor at traversing for clock descriptors. That is, when a device provides a bogus descriptor with a shorter bLength, the driver might hit out-of-bounds reads. For addressing it, this patch adds sanity checks to the validator functions for the clock descriptor traversal. When the descriptor length is shorter than expected, it's skipped in the loop. For the clock source and clock multiplier descriptors, we can just check bLength against the sizeof() of each descriptor type. OTOH, the clock selector descriptor of UAC2 and UAC3 has an array of bNrInPins elements and two more fields at its tail, hence those have to be checked in addition to the sizeof() check.
In the Linux kernel, the following vulnerability has been resolved: ocfs2: fix uninitialized value in ocfs2_file_read_iter() Syzbot has reported the following KMSAN splat: BUG: KMSAN: uninit-value in ocfs2_file_read_iter+0x9a4/0xf80 ocfs2_file_read_iter+0x9a4/0xf80 __io_read+0x8d4/0x20f0 io_read+0x3e/0xf0 io_issue_sqe+0x42b/0x22c0 io_wq_submit_work+0xaf9/0xdc0 io_worker_handle_work+0xd13/0x2110 io_wq_worker+0x447/0x1410 ret_from_fork+0x6f/0x90 ret_from_fork_asm+0x1a/0x30 Uninit was created at: __alloc_pages_noprof+0x9a7/0xe00 alloc_pages_mpol_noprof+0x299/0x990 alloc_pages_noprof+0x1bf/0x1e0 allocate_slab+0x33a/0x1250 ___slab_alloc+0x12ef/0x35e0 kmem_cache_alloc_bulk_noprof+0x486/0x1330 __io_alloc_req_refill+0x84/0x560 io_submit_sqes+0x172f/0x2f30 __se_sys_io_uring_enter+0x406/0x41c0 __x64_sys_io_uring_enter+0x11f/0x1a0 x64_sys_call+0x2b54/0x3ba0 do_syscall_64+0xcd/0x1e0 entry_SYSCALL_64_after_hwframe+0x77/0x7f Since an instance of 'struct kiocb' may be passed from the block layer with 'private' field uninitialized, introduce 'ocfs2_iocb_init_rw_locked()' and use it from where 'ocfs2_dio_end_io()' might take care, i.e. in 'ocfs2_file_read_iter()' and 'ocfs2_file_write_iter()'.
In the Linux kernel, the following vulnerability has been resolved: crypto: qat/qat_4xxx - fix off by one in uof_get_name() The fw_objs[] array has "num_objs" elements so the > needs to be >= to prevent an out of bounds read.
In the Linux kernel, the following vulnerability has been resolved: media: mgb4: protect driver against spectre Frequency range is set from sysfs via frequency_range_store(), being vulnerable to spectre, as reported by smatch: drivers/media/pci/mgb4/mgb4_cmt.c:231 mgb4_cmt_set_vin_freq_range() warn: potential spectre issue 'cmt_vals_in' [r] drivers/media/pci/mgb4/mgb4_cmt.c:238 mgb4_cmt_set_vin_freq_range() warn: possible spectre second half. 'reg_set' Fix it.
In the Linux kernel, the following vulnerability has been resolved: virtio_net: Add hash_key_length check Add hash_key_length check in virtnet_probe() to avoid possible out of bound errors when setting/reading the hash key.
In the Linux kernel, the following vulnerability has been resolved: bpf: Check validity of link->type in bpf_link_show_fdinfo() If a newly-added link type doesn't invoke BPF_LINK_TYPE(), accessing bpf_link_type_strs[link->type] may result in an out-of-bounds access. To spot such missed invocations early in the future, checking the validity of link->type in bpf_link_show_fdinfo() and emitting a warning when such invocations are missed.
In the Linux kernel, the following vulnerability has been resolved: slip: make slhc_remember() more robust against malicious packets syzbot found that slhc_remember() was missing checks against malicious packets [1]. slhc_remember() only checked the size of the packet was at least 20, which is not good enough. We need to make sure the packet includes the IPv4 and TCP header that are supposed to be carried. Add iph and th pointers to make the code more readable. [1] BUG: KMSAN: uninit-value in slhc_remember+0x2e8/0x7b0 drivers/net/slip/slhc.c:666 slhc_remember+0x2e8/0x7b0 drivers/net/slip/slhc.c:666 ppp_receive_nonmp_frame+0xe45/0x35e0 drivers/net/ppp/ppp_generic.c:2455 ppp_receive_frame drivers/net/ppp/ppp_generic.c:2372 [inline] ppp_do_recv+0x65f/0x40d0 drivers/net/ppp/ppp_generic.c:2212 ppp_input+0x7dc/0xe60 drivers/net/ppp/ppp_generic.c:2327 pppoe_rcv_core+0x1d3/0x720 drivers/net/ppp/pppoe.c:379 sk_backlog_rcv+0x13b/0x420 include/net/sock.h:1113 __release_sock+0x1da/0x330 net/core/sock.c:3072 release_sock+0x6b/0x250 net/core/sock.c:3626 pppoe_sendmsg+0x2b8/0xb90 drivers/net/ppp/pppoe.c:903 sock_sendmsg_nosec net/socket.c:729 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:744 ____sys_sendmsg+0x903/0xb60 net/socket.c:2602 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2656 __sys_sendmmsg+0x3c1/0x960 net/socket.c:2742 __do_sys_sendmmsg net/socket.c:2771 [inline] __se_sys_sendmmsg net/socket.c:2768 [inline] __x64_sys_sendmmsg+0xbc/0x120 net/socket.c:2768 x64_sys_call+0xb6e/0x3ba0 arch/x86/include/generated/asm/syscalls_64.h:308 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was created at: slab_post_alloc_hook mm/slub.c:4091 [inline] slab_alloc_node mm/slub.c:4134 [inline] kmem_cache_alloc_node_noprof+0x6bf/0xb80 mm/slub.c:4186 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:587 __alloc_skb+0x363/0x7b0 net/core/skbuff.c:678 alloc_skb include/linux/skbuff.h:1322 [inline] sock_wmalloc+0xfe/0x1a0 net/core/sock.c:2732 pppoe_sendmsg+0x3a7/0xb90 drivers/net/ppp/pppoe.c:867 sock_sendmsg_nosec net/socket.c:729 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:744 ____sys_sendmsg+0x903/0xb60 net/socket.c:2602 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2656 __sys_sendmmsg+0x3c1/0x960 net/socket.c:2742 __do_sys_sendmmsg net/socket.c:2771 [inline] __se_sys_sendmmsg net/socket.c:2768 [inline] __x64_sys_sendmmsg+0xbc/0x120 net/socket.c:2768 x64_sys_call+0xb6e/0x3ba0 arch/x86/include/generated/asm/syscalls_64.h:308 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f CPU: 0 UID: 0 PID: 5460 Comm: syz.2.33 Not tainted 6.12.0-rc2-syzkaller-00006-g87d6aab2389e #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
In the Linux kernel, the following vulnerability has been resolved: x86/entry_32: Clear CPU buffers after register restore in NMI return CPU buffers are currently cleared after call to exc_nmi, but before register state is restored. This may be okay for MDS mitigation but not for RDFS. Because RDFS mitigation requires CPU buffers to be cleared when registers don't have any sensitive data. Move CLEAR_CPU_BUFFERS after RESTORE_ALL_NMI.
In the Linux kernel, the following vulnerability has been resolved: ep93xx: clock: Fix off by one in ep93xx_div_recalc_rate() The psc->div[] array has psc->num_div elements. These values come from when we call clk_hw_register_div(). It's adc_divisors and ARRAY_SIZE(adc_divisors)) and so on. So this condition needs to be >= instead of > to prevent an out of bounds read.
In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix potential oob read in nilfs_btree_check_delete() The function nilfs_btree_check_delete(), which checks whether degeneration to direct mapping occurs before deleting a b-tree entry, causes memory access outside the block buffer when retrieving the maximum key if the root node has no entries. This does not usually happen because b-tree mappings with 0 child nodes are never created by mkfs.nilfs2 or nilfs2 itself. However, it can happen if the b-tree root node read from a device is configured that way, so fix this potential issue by adding a check for that case.
In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix ucode out-of-bounds read warning Clear warning that read ucode[] may out-of-bounds.
In the Linux kernel, the following vulnerability has been resolved: drm/amd/pm: fix the Out-of-bounds read warning using index i - 1U may beyond element index for mc_data[] when i = 0.