In the Linux kernel, the following vulnerability has been resolved: virtio_net: correct netdev_tx_reset_queue() invocation point When virtnet_close is followed by virtnet_open, some TX completions can possibly remain unconsumed, until they are finally processed during the first NAPI poll after the netdev_tx_reset_queue(), resulting in a crash [1]. Commit b96ed2c97c79 ("virtio_net: move netdev_tx_reset_queue() call before RX napi enable") was not sufficient to eliminate all BQL crash cases for virtio-net. This issue can be reproduced with the latest net-next master by running: `while :; do ip l set DEV down; ip l set DEV up; done` under heavy network TX load from inside the machine. netdev_tx_reset_queue() can actually be dropped from virtnet_open path; the device is not stopped in any case. For BQL core part, it's just like traffic nearly ceases to exist for some period. For stall detector added to BQL, even if virtnet_close could somehow lead to some TX completions delayed for long, followed by virtnet_open, we can just take it as stall as mentioned in commit 6025b9135f7a ("net: dqs: add NIC stall detector based on BQL"). Note also that users can still reset stall_max via sysfs. So, drop netdev_tx_reset_queue() from virtnet_enable_queue_pair(). This eliminates the BQL crashes. As a result, netdev_tx_reset_queue() is now explicitly required in freeze/restore path. This patch adds it to immediately after free_unused_bufs(), following the rule of thumb: netdev_tx_reset_queue() should follow any SKB freeing not followed by netdev_tx_completed_queue(). This seems the most consistent and streamlined approach, and now netdev_tx_reset_queue() runs whenever free_unused_bufs() is done. [1]: ------------[ cut here ]------------ kernel BUG at lib/dynamic_queue_limits.c:99! Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 7 UID: 0 PID: 1598 Comm: ip Tainted: G N 6.12.0net-next_main+ #2 Tainted: [N]=TEST Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), \ BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 RIP: 0010:dql_completed+0x26b/0x290 Code: b7 c2 49 89 e9 44 89 da 89 c6 4c 89 d7 e8 ed 17 47 00 58 65 ff 0d 4d 27 90 7e 0f 85 fd fe ff ff e8 ea 53 8d ff e9 f3 fe ff ff <0f> 0b 01 d2 44 89 d1 29 d1 ba 00 00 00 00 0f 48 ca e9 28 ff ff ff RSP: 0018:ffffc900002b0d08 EFLAGS: 00010297 RAX: 0000000000000000 RBX: ffff888102398c80 RCX: 0000000080190009 RDX: 0000000000000000 RSI: 000000000000006a RDI: 0000000000000000 RBP: ffff888102398c00 R08: 0000000000000000 R09: 0000000000000000 R10: 00000000000000ca R11: 0000000000015681 R12: 0000000000000001 R13: ffffc900002b0d68 R14: ffff88811115e000 R15: ffff8881107aca40 FS: 00007f41ded69500(0000) GS:ffff888667dc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000556ccc2dc1a0 CR3: 0000000104fd8003 CR4: 0000000000772ef0 PKRU: 55555554 Call Trace: <IRQ> ? die+0x32/0x80 ? do_trap+0xd9/0x100 ? dql_completed+0x26b/0x290 ? dql_completed+0x26b/0x290 ? do_error_trap+0x6d/0xb0 ? dql_completed+0x26b/0x290 ? exc_invalid_op+0x4c/0x60 ? dql_completed+0x26b/0x290 ? asm_exc_invalid_op+0x16/0x20 ? dql_completed+0x26b/0x290 __free_old_xmit+0xff/0x170 [virtio_net] free_old_xmit+0x54/0xc0 [virtio_net] virtnet_poll+0xf4/0xe30 [virtio_net] ? __update_load_avg_cfs_rq+0x264/0x2d0 ? update_curr+0x35/0x260 ? reweight_entity+0x1be/0x260 __napi_poll.constprop.0+0x28/0x1c0 net_rx_action+0x329/0x420 ? enqueue_hrtimer+0x35/0x90 ? trace_hardirqs_on+0x1d/0x80 ? kvm_sched_clock_read+0xd/0x20 ? sched_clock+0xc/0x30 ? kvm_sched_clock_read+0xd/0x20 ? sched_clock+0xc/0x30 ? sched_clock_cpu+0xd/0x1a0 handle_softirqs+0x138/0x3e0 do_softirq.part.0+0x89/0xc0 </IRQ> <TASK> __local_bh_enable_ip+0xa7/0xb0 virtnet_open+0xc8/0x310 [virtio_net] __dev_open+0xfa/0x1b0 __dev_change_flags+0x1de/0x250 dev_change_flags+0x22/0x60 do_setlink.isra.0+0x2df/0x10b0 ? rtnetlink_rcv_msg+0x34f/0x3f0 ? netlink_rcv_skb+0x54/0x100 ? netlink_unicas ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix crash caused by calling __xfrm_state_delete() twice The km.state is not checked in driver's delayed work. When xfrm_state_check_expire() is called, the state can be reset to XFRM_STATE_EXPIRED, even if it is XFRM_STATE_DEAD already. This happens when xfrm state is deleted, but not freed yet. As __xfrm_state_delete() is called again in xfrm timer, the following crash occurs. To fix this issue, skip xfrm_state_check_expire() if km.state is not XFRM_STATE_VALID. Oops: general protection fault, probably for non-canonical address 0xdead000000000108: 0000 [#1] SMP CPU: 5 UID: 0 PID: 7448 Comm: kworker/u102:2 Not tainted 6.11.0-rc2+ #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Workqueue: mlx5e_ipsec: eth%d mlx5e_ipsec_handle_sw_limits [mlx5_core] RIP: 0010:__xfrm_state_delete+0x3d/0x1b0 Code: 0f 84 8b 01 00 00 48 89 fd c6 87 c8 00 00 00 05 48 8d bb 40 10 00 00 e8 11 04 1a 00 48 8b 95 b8 00 00 00 48 8b 85 c0 00 00 00 <48> 89 42 08 48 89 10 48 8b 55 10 48 b8 00 01 00 00 00 00 ad de 48 RSP: 0018:ffff88885f945ec8 EFLAGS: 00010246 RAX: dead000000000122 RBX: ffffffff82afa940 RCX: 0000000000000036 RDX: dead000000000100 RSI: 0000000000000000 RDI: ffffffff82afb980 RBP: ffff888109a20340 R08: ffff88885f945ea0 R09: 0000000000000000 R10: 0000000000000000 R11: ffff88885f945ff8 R12: 0000000000000246 R13: ffff888109a20340 R14: ffff88885f95f420 R15: ffff88885f95f400 FS: 0000000000000000(0000) GS:ffff88885f940000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f2163102430 CR3: 00000001128d6001 CR4: 0000000000370eb0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <IRQ> ? die_addr+0x33/0x90 ? exc_general_protection+0x1a2/0x390 ? asm_exc_general_protection+0x22/0x30 ? __xfrm_state_delete+0x3d/0x1b0 ? __xfrm_state_delete+0x2f/0x1b0 xfrm_timer_handler+0x174/0x350 ? __xfrm_state_delete+0x1b0/0x1b0 __hrtimer_run_queues+0x121/0x270 hrtimer_run_softirq+0x88/0xd0 handle_softirqs+0xcc/0x270 do_softirq+0x3c/0x50 </IRQ> <TASK> __local_bh_enable_ip+0x47/0x50 mlx5e_ipsec_handle_sw_limits+0x7d/0x90 [mlx5_core] process_one_work+0x137/0x2d0 worker_thread+0x28d/0x3a0 ? rescuer_thread+0x480/0x480 kthread+0xb8/0xe0 ? kthread_park+0x80/0x80 ret_from_fork+0x2d/0x50 ? kthread_park+0x80/0x80 ret_from_fork_asm+0x11/0x20 </TASK>

In the Linux kernel, the following vulnerability has been resolved: ACPI: battery: Fix possible crash when unregistering a battery hook When a battery hook returns an error when adding a new battery, then the battery hook is automatically unregistered. However the battery hook provider cannot know that, so it will later call battery_hook_unregister() on the already unregistered battery hook, resulting in a crash. Fix this by using the list head to mark already unregistered battery hooks as already being unregistered so that they can be ignored by battery_hook_unregister().

In the Linux kernel, the following vulnerability has been resolved: io_uring/futex: ensure io_futex_wait() cleans up properly on failure The io_futex_data is allocated upfront and assigned to the io_kiocb async_data field, but the request isn't marked with REQ_F_ASYNC_DATA at that point. Those two should always go together, as the flag tells io_uring whether the field is valid or not. Additionally, on failure cleanup, the futex handler frees the data but does not clear ->async_data. Clear the data and the flag in the error path as well. Thanks to Trend Micro Zero Day Initiative and particularly ReDress for reporting this.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix node corruption in ar->arvifs list In current WLAN recovery code flow, ath12k_core_halt() only reinitializes the "arvifs" list head. This will cause the list node immediately following the list head to become an invalid list node. Because the prev of that node still points to the list head "arvifs", but the next of the list head "arvifs" no longer points to that list node. When a WLAN recovery occurs during the execution of a vif removal, and it happens before the spin_lock_bh(&ar->data_lock) in ath12k_mac_vdev_delete(), list_del() will detect the previously mentioned situation, thereby triggering a kernel panic. The fix is to remove and reinitialize all vif list nodes from the list head "arvifs" during WLAN halt. The reinitialization is to make the list nodes valid, ensuring that the list_del() in ath12k_mac_vdev_delete() can execute normally. Call trace: __list_del_entry_valid_or_report+0xd4/0x100 (P) ath12k_mac_remove_link_interface.isra.0+0xf8/0x2e4 [ath12k] ath12k_scan_vdev_clean_work+0x40/0x164 [ath12k] cfg80211_wiphy_work+0xfc/0x100 process_one_work+0x164/0x2d0 worker_thread+0x254/0x380 kthread+0xfc/0x100 ret_from_fork+0x10/0x20 The change is mostly copied from the ath11k patch: https://lore.kernel.org/all/20250320053145.3445187-1-quic_stonez@quicinc.com/ Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1

An issue was discovered in the Linux kernel before 5.16.5. There is a memory leak in yam_siocdevprivate in drivers/net/hamradio/yam.c.

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: regulatory: improve invalid hints checking Syzbot keeps reporting an issue [1] that occurs when erroneous symbols sent from userspace get through into user_alpha2[] via regulatory_hint_user() call. Such invalid regulatory hints should be rejected. While a sanity check from commit 47caf685a685 ("cfg80211: regulatory: reject invalid hints") looks to be enough to deter these very cases, there is a way to get around it due to 2 reasons. 1) The way isalpha() works, symbols other than latin lower and upper letters may be used to determine a country/domain. For instance, greek letters will also be considered upper/lower letters and for such characters isalpha() will return true as well. However, ISO-3166-1 alpha2 codes should only hold latin characters. 2) While processing a user regulatory request, between reg_process_hint_user() and regulatory_hint_user() there happens to be a call to queue_regulatory_request() which modifies letters in request->alpha2[] with toupper(). This works fine for latin symbols, less so for weird letter characters from the second part of _ctype[]. Syzbot triggers a warning in is_user_regdom_saved() by first sending over an unexpected non-latin letter that gets malformed by toupper() into a character that ends up failing isalpha() check. Prevent this by enhancing is_an_alpha2() to ensure that incoming symbols are latin letters and nothing else. [1] Syzbot report: ------------[ cut here ]------------ Unexpected user alpha2: A� WARNING: CPU: 1 PID: 964 at net/wireless/reg.c:442 is_user_regdom_saved net/wireless/reg.c:440 [inline] WARNING: CPU: 1 PID: 964 at net/wireless/reg.c:442 restore_alpha2 net/wireless/reg.c:3424 [inline] WARNING: CPU: 1 PID: 964 at net/wireless/reg.c:442 restore_regulatory_settings+0x3c0/0x1e50 net/wireless/reg.c:3516 Modules linked in: CPU: 1 UID: 0 PID: 964 Comm: kworker/1:2 Not tainted 6.12.0-rc5-syzkaller-00044-gc1e939a21eb1 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 Workqueue: events_power_efficient crda_timeout_work RIP: 0010:is_user_regdom_saved net/wireless/reg.c:440 [inline] RIP: 0010:restore_alpha2 net/wireless/reg.c:3424 [inline] RIP: 0010:restore_regulatory_settings+0x3c0/0x1e50 net/wireless/reg.c:3516 ... Call Trace: <TASK> crda_timeout_work+0x27/0x50 net/wireless/reg.c:542 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0xa65/0x1850 kernel/workqueue.c:3310 worker_thread+0x870/0xd30 kernel/workqueue.c:3391 kthread+0x2f2/0x390 kernel/kthread.c:389 ret_from_fork+0x4d/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 </TASK>

In the Linux kernel, the following vulnerability has been resolved: sctp: sysctl: rto_min/max: avoid using current->nsproxy As mentioned in a previous commit of this series, using the 'net' structure via 'current' is not recommended for different reasons: - Inconsistency: getting info from the reader's/writer's netns vs only from the opener's netns. - current->nsproxy can be NULL in some cases, resulting in an 'Oops' (null-ptr-deref), e.g. when the current task is exiting, as spotted by syzbot [1] using acct(2). The 'net' structure can be obtained from the table->data using container_of(). Note that table->data could also be used directly, as this is the only member needed from the 'net' structure, but that would increase the size of this fix, to use '*data' everywhere 'net->sctp.rto_min/max' is used.

A NULL pointer dereference was found in the Linux kernel's KVM when dirty ring logging is enabled without an active vCPU context. An unprivileged local attacker on the host may use this flaw to cause a kernel oops condition and thus a denial of service by issuing a KVM_XEN_HVM_SET_ATTR ioctl. This flaw affects Linux kernel versions prior to 5.17-rc1.

In the Linux kernel, the following vulnerability has been resolved: Input: appletouch - initialize work before device registration Syzbot has reported warning in __flush_work(). This warning is caused by work->func == NULL, which means missing work initialization. This may happen, since input_dev->close() calls cancel_work_sync(&dev->work), but dev->work initalization happens _after_ input_register_device() call. So this patch moves dev->work initialization before registering input device

In the Linux kernel, the following vulnerability has been resolved: eth: bnxt: return fail if interface is down in bnxt_queue_mem_alloc() The bnxt_queue_mem_alloc() is called to allocate new queue memory when a queue is restarted. It internally accesses rx buffer descriptor corresponding to the index. The rx buffer descriptor is allocated and set when the interface is up and it's freed when the interface is down. So, if queue is restarted if interface is down, kernel panic occurs. Splat looks like: BUG: unable to handle page fault for address: 000000000000b240 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 3 UID: 0 PID: 1563 Comm: ncdevmem2 Not tainted 6.14.0-rc2+ #9 844ddba6e7c459cafd0bf4db9a3198e Hardware name: ASUS System Product Name/PRIME Z690-P D4, BIOS 0603 11/01/2021 RIP: 0010:bnxt_queue_mem_alloc+0x3f/0x4e0 [bnxt_en] Code: 41 54 4d 89 c4 4d 69 c0 c0 05 00 00 55 48 89 f5 53 48 89 fb 4c 8d b5 40 05 00 00 48 83 ec 15 RSP: 0018:ffff9dcc83fef9e8 EFLAGS: 00010202 RAX: ffffffffc0457720 RBX: ffff934ed8d40000 RCX: 0000000000000000 RDX: 000000000000001f RSI: ffff934ea508f800 RDI: ffff934ea508f808 RBP: ffff934ea508f800 R08: 000000000000b240 R09: ffff934e84f4b000 R10: ffff9dcc83fefa30 R11: ffff934e84f4b000 R12: 000000000000001f R13: ffff934ed8d40ac0 R14: ffff934ea508fd40 R15: ffff934e84f4b000 FS: 00007fa73888c740(0000) GS:ffff93559f780000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000000b240 CR3: 0000000145a2e000 CR4: 00000000007506f0 PKRU: 55555554 Call Trace: <TASK> ? __die+0x20/0x70 ? page_fault_oops+0x15a/0x460 ? exc_page_fault+0x6e/0x180 ? asm_exc_page_fault+0x22/0x30 ? __pfx_bnxt_queue_mem_alloc+0x10/0x10 [bnxt_en 7f85e76f4d724ba07471d7e39d9e773aea6597b7] ? bnxt_queue_mem_alloc+0x3f/0x4e0 [bnxt_en 7f85e76f4d724ba07471d7e39d9e773aea6597b7] netdev_rx_queue_restart+0xc5/0x240 net_devmem_bind_dmabuf_to_queue+0xf8/0x200 netdev_nl_bind_rx_doit+0x3a7/0x450 genl_family_rcv_msg_doit+0xd9/0x130 genl_rcv_msg+0x184/0x2b0 ? __pfx_netdev_nl_bind_rx_doit+0x10/0x10 ? __pfx_genl_rcv_msg+0x10/0x10 netlink_rcv_skb+0x54/0x100 genl_rcv+0x24/0x40 ...

The Linux kernel was found vulnerable out of bounds memory access in the drivers/video/fbdev/sm712fb.c:smtcfb_read() function. The vulnerability could result in local attackers being able to crash the kernel.

In the Linux kernel, the following vulnerability has been resolved: bpf, arm64: Clear prog->jited_len along prog->jited syzbot reported an illegal copy_to_user() attempt from bpf_prog_get_info_by_fd() [1] There was no repro yet on this bug, but I think that commit 0aef499f3172 ("mm/usercopy: Detect vmalloc overruns") is exposing a prior bug in bpf arm64. bpf_prog_get_info_by_fd() looks at prog->jited_len to determine if the JIT image can be copied out to user space. My theory is that syzbot managed to get a prog where prog->jited_len has been set to 43, while prog->bpf_func has ben cleared. It is not clear why copy_to_user(uinsns, NULL, ulen) is triggering this particular warning. I thought find_vma_area(NULL) would not find a vm_struct. As we do not hold vmap_area_lock spinlock, it might be possible that the found vm_struct was garbage. [1] usercopy: Kernel memory exposure attempt detected from vmalloc (offset 792633534417210172, size 43)! kernel BUG at mm/usercopy.c:101! Internal error: Oops - BUG: 0 [#1] PREEMPT SMP Modules linked in: CPU: 0 PID: 25002 Comm: syz-executor.1 Not tainted 5.18.0-syzkaller-10139-g8291eaafed36 #0 Hardware name: linux,dummy-virt (DT) pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : usercopy_abort+0x90/0x94 mm/usercopy.c:101 lr : usercopy_abort+0x90/0x94 mm/usercopy.c:89 sp : ffff80000b773a20 x29: ffff80000b773a30 x28: faff80000b745000 x27: ffff80000b773b48 x26: 0000000000000000 x25: 000000000000002b x24: 0000000000000000 x23: 00000000000000e0 x22: ffff80000b75db67 x21: 0000000000000001 x20: 000000000000002b x19: ffff80000b75db3c x18: 00000000fffffffd x17: 2820636f6c6c616d x16: 76206d6f72662064 x15: 6574636574656420 x14: 74706d6574746120 x13: 2129333420657a69 x12: 73202c3237313031 x11: 3237313434333533 x10: 3336323937207465 x9 : 657275736f707865 x8 : ffff80000a30c550 x7 : ffff80000b773830 x6 : ffff80000b773830 x5 : 0000000000000000 x4 : ffff00007fbbaa10 x3 : 0000000000000000 x2 : 0000000000000000 x1 : f7ff000028fc0000 x0 : 0000000000000064 Call trace: usercopy_abort+0x90/0x94 mm/usercopy.c:89 check_heap_object mm/usercopy.c:186 [inline] __check_object_size mm/usercopy.c:252 [inline] __check_object_size+0x198/0x36c mm/usercopy.c:214 check_object_size include/linux/thread_info.h:199 [inline] check_copy_size include/linux/thread_info.h:235 [inline] copy_to_user include/linux/uaccess.h:159 [inline] bpf_prog_get_info_by_fd.isra.0+0xf14/0xfdc kernel/bpf/syscall.c:3993 bpf_obj_get_info_by_fd+0x12c/0x510 kernel/bpf/syscall.c:4253 __sys_bpf+0x900/0x2150 kernel/bpf/syscall.c:4956 __do_sys_bpf kernel/bpf/syscall.c:5021 [inline] __se_sys_bpf kernel/bpf/syscall.c:5019 [inline] __arm64_sys_bpf+0x28/0x40 kernel/bpf/syscall.c:5019 __invoke_syscall arch/arm64/kernel/syscall.c:38 [inline] invoke_syscall+0x48/0x114 arch/arm64/kernel/syscall.c:52 el0_svc_common.constprop.0+0x44/0xec arch/arm64/kernel/syscall.c:142 do_el0_svc+0xa0/0xc0 arch/arm64/kernel/syscall.c:206 el0_svc+0x44/0xb0 arch/arm64/kernel/entry-common.c:624 el0t_64_sync_handler+0x1ac/0x1b0 arch/arm64/kernel/entry-common.c:642 el0t_64_sync+0x198/0x19c arch/arm64/kernel/entry.S:581 Code: aa0003e3 d00038c0 91248000 97fff65f (d4210000)

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw88: sdio: Honor the host max_req_size in the RX path Lukas reports skb_over_panic errors on his Banana Pi BPI-CM4 which comes with an Amlogic A311D (G12B) SoC and a RTL8822CS SDIO wifi/Bluetooth combo card. The error he observed is identical to what has been fixed in commit e967229ead0e ("wifi: rtw88: sdio: Check the HISR RX_REQUEST bit in rtw_sdio_rx_isr()") but that commit didn't fix Lukas' problem. Lukas found that disabling or limiting RX aggregation works around the problem for some time (but does not fully fix it). In the following discussion a few key topics have been discussed which have an impact on this problem: - The Amlogic A311D (G12B) SoC has a hardware bug in the SDIO controller which prevents DMA transfers. Instead all transfers need to go through the controller SRAM which limits transfers to 1536 bytes - rtw88 chips don't split incoming (RX) packets, so if a big packet is received this is forwarded to the host in it's original form - rtw88 chips can do RX aggregation, meaning more multiple incoming packets can be pulled by the host from the card with one MMC/SDIO transfer. This Depends on settings in the REG_RXDMA_AGG_PG_TH register (BIT_RXDMA_AGG_PG_TH limits the number of packets that will be aggregated, BIT_DMA_AGG_TO_V1 configures a timeout for aggregation and BIT_EN_PRE_CALC makes the chip honor the limits more effectively) Use multiple consecutive reads in rtw_sdio_read_port() and limit the number of bytes which are copied by the host from the card in one MMC/SDIO transfer. This allows receiving a buffer that's larger than the hosts max_req_size (number of bytes which can be transferred in one MMC/SDIO transfer). As a result of this the skb_over_panic error is gone as the rtw88 driver is now able to receive more than 1536 bytes from the card (either because the incoming packet is larger than that or because multiple packets have been aggregated). In case of an receive errors (-EILSEQ has been observed by Lukas) we need to drain the remaining data from the card's buffer, otherwise the card will return corrupt data for the next rtw_sdio_read_port() call.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix possible NULL dereference in amdgpu_ras_query_error_status_helper() Return invalid error code -EINVAL for invalid block id. Fixes the below: drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:1183 amdgpu_ras_query_error_status_helper() error: we previously assumed 'info' could be null (see line 1176)

In the Linux kernel, the following vulnerability has been resolved: drm/i915: Fix crash in auto_retire The retire logic uses the 2 lower bits of the pointer to the retire function to store flags. However, the auto_retire function is not guaranteed to be aligned to a multiple of 4, which causes crashes as we jump to the wrong address, for example like this: 2021-04-24T18:03:53.804300Z WARNING kernel: [ 516.876901] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI 2021-04-24T18:03:53.804310Z WARNING kernel: [ 516.876906] CPU: 7 PID: 146 Comm: kworker/u16:6 Tainted: G U 5.4.105-13595-g3cd84167b2df #1 2021-04-24T18:03:53.804311Z WARNING kernel: [ 516.876907] Hardware name: Google Volteer2/Volteer2, BIOS Google_Volteer2.13672.76.0 02/22/2021 2021-04-24T18:03:53.804312Z WARNING kernel: [ 516.876911] Workqueue: events_unbound active_work 2021-04-24T18:03:53.804313Z WARNING kernel: [ 516.876914] RIP: 0010:auto_retire+0x1/0x20 2021-04-24T18:03:53.804314Z WARNING kernel: [ 516.876916] Code: e8 01 f2 ff ff eb 02 31 db 48 89 d8 5b 5d c3 0f 1f 44 00 00 55 48 89 e5 f0 ff 87 c8 00 00 00 0f 88 ab 47 4a 00 31 c0 5d c3 0f <1f> 44 00 00 55 48 89 e5 f0 ff 8f c8 00 00 00 0f 88 9a 47 4a 00 74 2021-04-24T18:03:53.804319Z WARNING kernel: [ 516.876918] RSP: 0018:ffff9b4d809fbe38 EFLAGS: 00010286 2021-04-24T18:03:53.804320Z WARNING kernel: [ 516.876919] RAX: 0000000000000007 RBX: ffff927915079600 RCX: 0000000000000007 2021-04-24T18:03:53.804320Z WARNING kernel: [ 516.876921] RDX: ffff9b4d809fbe40 RSI: 0000000000000286 RDI: ffff927915079600 2021-04-24T18:03:53.804321Z WARNING kernel: [ 516.876922] RBP: ffff9b4d809fbe68 R08: 8080808080808080 R09: fefefefefefefeff 2021-04-24T18:03:53.804321Z WARNING kernel: [ 516.876924] R10: 0000000000000010 R11: ffffffff92e44bd8 R12: ffff9279150796a0 2021-04-24T18:03:53.804322Z WARNING kernel: [ 516.876925] R13: ffff92791c368180 R14: ffff927915079640 R15: 000000001c867605 2021-04-24T18:03:53.804323Z WARNING kernel: [ 516.876926] FS: 0000000000000000(0000) GS:ffff92791ffc0000(0000) knlGS:0000000000000000 2021-04-24T18:03:53.804323Z WARNING kernel: [ 516.876928] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 2021-04-24T18:03:53.804324Z WARNING kernel: [ 516.876929] CR2: 0000239514955000 CR3: 00000007f82da001 CR4: 0000000000760ee0 2021-04-24T18:03:53.804325Z WARNING kernel: [ 516.876930] PKRU: 55555554 2021-04-24T18:03:53.804325Z WARNING kernel: [ 516.876931] Call Trace: 2021-04-24T18:03:53.804326Z WARNING kernel: [ 516.876935] __active_retire+0x77/0xcf 2021-04-24T18:03:53.804326Z WARNING kernel: [ 516.876939] process_one_work+0x1da/0x394 2021-04-24T18:03:53.804327Z WARNING kernel: [ 516.876941] worker_thread+0x216/0x375 2021-04-24T18:03:53.804327Z WARNING kernel: [ 516.876944] kthread+0x147/0x156 2021-04-24T18:03:53.804335Z WARNING kernel: [ 516.876946] ? pr_cont_work+0x58/0x58 2021-04-24T18:03:53.804335Z WARNING kernel: [ 516.876948] ? kthread_blkcg+0x2e/0x2e 2021-04-24T18:03:53.804336Z WARNING kernel: [ 516.876950] ret_from_fork+0x1f/0x40 2021-04-24T18:03:53.804336Z WARNING kernel: [ 516.876952] Modules linked in: cdc_mbim cdc_ncm cdc_wdm xt_cgroup rfcomm cmac algif_hash algif_skcipher af_alg xt_MASQUERADE uinput snd_soc_rt5682_sdw snd_soc_rt5682 snd_soc_max98373_sdw snd_soc_max98373 snd_soc_rl6231 regmap_sdw snd_soc_sof_sdw snd_soc_hdac_hdmi snd_soc_dmic snd_hda_codec_hdmi snd_sof_pci snd_sof_intel_hda_common intel_ipu6_psys snd_sof_xtensa_dsp soundwire_intel soundwire_generic_allocation soundwire_cadence snd_sof_intel_hda snd_sof snd_soc_hdac_hda snd_soc_acpi_intel_match snd_soc_acpi snd_hda_ext_core soundwire_bus snd_hda_intel snd_intel_dspcfg snd_hda_codec snd_hwdep snd_hda_core intel_ipu6_isys videobuf2_dma_contig videobuf2_v4l2 videobuf2_common videobuf2_memops mei_hdcp intel_ipu6 ov2740 ov8856 at24 sx9310 dw9768 v4l2_fwnode cros_ec_typec intel_pmc_mux roles acpi_als typec fuse iio_trig_sysfs cros_ec_light_prox cros_ec_lid_angle cros_ec_sensors cros ---truncated---

There are use-after-free vulnerabilities caused by timer handler in net/rose/rose_timer.c of linux that allow attackers to crash linux kernel without any privileges.

In the Linux kernel, the following vulnerability has been resolved: net: ibmveth: make veth_pool_store stop hanging v2: - Created a single error handling unlock and exit in veth_pool_store - Greatly expanded commit message with previous explanatory-only text Summary: Use rtnl_mutex to synchronize veth_pool_store with itself, ibmveth_close and ibmveth_open, preventing multiple calls in a row to napi_disable. Background: Two (or more) threads could call veth_pool_store through writing to /sys/devices/vio/30000002/pool*/*. You can do this easily with a little shell script. This causes a hang. I configured LOCKDEP, compiled ibmveth.c with DEBUG, and built a new kernel. I ran this test again and saw: Setting pool0/active to 0 Setting pool1/active to 1 [ 73.911067][ T4365] ibmveth 30000002 eth0: close starting Setting pool1/active to 1 Setting pool1/active to 0 [ 73.911367][ T4366] ibmveth 30000002 eth0: close starting [ 73.916056][ T4365] ibmveth 30000002 eth0: close complete [ 73.916064][ T4365] ibmveth 30000002 eth0: open starting [ 110.808564][ T712] systemd-journald[712]: Sent WATCHDOG=1 notification. [ 230.808495][ T712] systemd-journald[712]: Sent WATCHDOG=1 notification. [ 243.683786][ T123] INFO: task stress.sh:4365 blocked for more than 122 seconds. [ 243.683827][ T123] Not tainted 6.14.0-01103-g2df0c02dab82-dirty #8 [ 243.683833][ T123] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 243.683838][ T123] task:stress.sh state:D stack:28096 pid:4365 tgid:4365 ppid:4364 task_flags:0x400040 flags:0x00042000 [ 243.683852][ T123] Call Trace: [ 243.683857][ T123] [c00000000c38f690] [0000000000000001] 0x1 (unreliable) [ 243.683868][ T123] [c00000000c38f840] [c00000000001f908] __switch_to+0x318/0x4e0 [ 243.683878][ T123] [c00000000c38f8a0] [c000000001549a70] __schedule+0x500/0x12a0 [ 243.683888][ T123] [c00000000c38f9a0] [c00000000154a878] schedule+0x68/0x210 [ 243.683896][ T123] [c00000000c38f9d0] [c00000000154ac80] schedule_preempt_disabled+0x30/0x50 [ 243.683904][ T123] [c00000000c38fa00] [c00000000154dbb0] __mutex_lock+0x730/0x10f0 [ 243.683913][ T123] [c00000000c38fb10] [c000000001154d40] napi_enable+0x30/0x60 [ 243.683921][ T123] [c00000000c38fb40] [c000000000f4ae94] ibmveth_open+0x68/0x5dc [ 243.683928][ T123] [c00000000c38fbe0] [c000000000f4aa20] veth_pool_store+0x220/0x270 [ 243.683936][ T123] [c00000000c38fc70] [c000000000826278] sysfs_kf_write+0x68/0xb0 [ 243.683944][ T123] [c00000000c38fcb0] [c0000000008240b8] kernfs_fop_write_iter+0x198/0x2d0 [ 243.683951][ T123] [c00000000c38fd00] [c00000000071b9ac] vfs_write+0x34c/0x650 [ 243.683958][ T123] [c00000000c38fdc0] [c00000000071bea8] ksys_write+0x88/0x150 [ 243.683966][ T123] [c00000000c38fe10] [c0000000000317f4] system_call_exception+0x124/0x340 [ 243.683973][ T123] [c00000000c38fe50] [c00000000000d05c] system_call_vectored_common+0x15c/0x2ec ... [ 243.684087][ T123] Showing all locks held in the system: [ 243.684095][ T123] 1 lock held by khungtaskd/123: [ 243.684099][ T123] #0: c00000000278e370 (rcu_read_lock){....}-{1:2}, at: debug_show_all_locks+0x50/0x248 [ 243.684114][ T123] 4 locks held by stress.sh/4365: [ 243.684119][ T123] #0: c00000003a4cd3f8 (sb_writers#3){.+.+}-{0:0}, at: ksys_write+0x88/0x150 [ 243.684132][ T123] #1: c000000041aea888 (&of->mutex#2){+.+.}-{3:3}, at: kernfs_fop_write_iter+0x154/0x2d0 [ 243.684143][ T123] #2: c0000000366fb9a8 (kn->active#64){.+.+}-{0:0}, at: kernfs_fop_write_iter+0x160/0x2d0 [ 243.684155][ T123] #3: c000000035ff4cb8 (&dev->lock){+.+.}-{3:3}, at: napi_enable+0x30/0x60 [ 243.684166][ T123] 5 locks held by stress.sh/4366: [ 243.684170][ T123] #0: c00000003a4cd3f8 (sb_writers#3){.+.+}-{0:0}, at: ksys_write+0x88/0x150 [ 243. ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net: fix geneve_opt length integer overflow struct geneve_opt uses 5 bit length for each single option, which means every vary size option should be smaller than 128 bytes. However, all current related Netlink policies cannot promise this length condition and the attacker can exploit a exact 128-byte size option to *fake* a zero length option and confuse the parsing logic, further achieve heap out-of-bounds read. One example crash log is like below: [ 3.905425] ================================================================== [ 3.905925] BUG: KASAN: slab-out-of-bounds in nla_put+0xa9/0xe0 [ 3.906255] Read of size 124 at addr ffff888005f291cc by task poc/177 [ 3.906646] [ 3.906775] CPU: 0 PID: 177 Comm: poc-oob-read Not tainted 6.1.132 #1 [ 3.907131] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 [ 3.907784] Call Trace: [ 3.907925] <TASK> [ 3.908048] dump_stack_lvl+0x44/0x5c [ 3.908258] print_report+0x184/0x4be [ 3.909151] kasan_report+0xc5/0x100 [ 3.909539] kasan_check_range+0xf3/0x1a0 [ 3.909794] memcpy+0x1f/0x60 [ 3.909968] nla_put+0xa9/0xe0 [ 3.910147] tunnel_key_dump+0x945/0xba0 [ 3.911536] tcf_action_dump_1+0x1c1/0x340 [ 3.912436] tcf_action_dump+0x101/0x180 [ 3.912689] tcf_exts_dump+0x164/0x1e0 [ 3.912905] fw_dump+0x18b/0x2d0 [ 3.913483] tcf_fill_node+0x2ee/0x460 [ 3.914778] tfilter_notify+0xf4/0x180 [ 3.915208] tc_new_tfilter+0xd51/0x10d0 [ 3.918615] rtnetlink_rcv_msg+0x4a2/0x560 [ 3.919118] netlink_rcv_skb+0xcd/0x200 [ 3.919787] netlink_unicast+0x395/0x530 [ 3.921032] netlink_sendmsg+0x3d0/0x6d0 [ 3.921987] __sock_sendmsg+0x99/0xa0 [ 3.922220] __sys_sendto+0x1b7/0x240 [ 3.922682] __x64_sys_sendto+0x72/0x90 [ 3.922906] do_syscall_64+0x5e/0x90 [ 3.923814] entry_SYSCALL_64_after_hwframe+0x6e/0xd8 [ 3.924122] RIP: 0033:0x7e83eab84407 [ 3.924331] Code: 48 89 fa 4c 89 df e8 38 aa 00 00 8b 93 08 03 00 00 59 5e 48 83 f8 fc 74 1a 5b c3 0f 1f 84 00 00 00 00 00 48 8b 44 24 10 0f 05 <5b> c3 0f 1f 80 00 00 00 00 83 e2 39 83 faf [ 3.925330] RSP: 002b:00007ffff505e370 EFLAGS: 00000202 ORIG_RAX: 000000000000002c [ 3.925752] RAX: ffffffffffffffda RBX: 00007e83eaafa740 RCX: 00007e83eab84407 [ 3.926173] RDX: 00000000000001a8 RSI: 00007ffff505e3c0 RDI: 0000000000000003 [ 3.926587] RBP: 00007ffff505f460 R08: 00007e83eace1000 R09: 000000000000000c [ 3.926977] R10: 0000000000000000 R11: 0000000000000202 R12: 00007ffff505f3c0 [ 3.927367] R13: 00007ffff505f5c8 R14: 00007e83ead1b000 R15: 00005d4fbbe6dcb8 Fix these issues by enforing correct length condition in related policies.

In the Linux kernel, the following vulnerability has been resolved: dpll: fix xa_alloc_cyclic() error handling In case of returning 1 from xa_alloc_cyclic() (wrapping) ERR_PTR(1) will be returned, which will cause IS_ERR() to be false. Which can lead to dereference not allocated pointer (pin). Fix it by checking if err is lower than zero. This wasn't found in real usecase, only noticed. Credit to Pierre.

In the Linux kernel, the following vulnerability has been resolved: ipmi: Fix UAF when uninstall ipmi_si and ipmi_msghandler module Hi, When testing install and uninstall of ipmi_si.ko and ipmi_msghandler.ko, the system crashed. The log as follows: [ 141.087026] BUG: unable to handle kernel paging request at ffffffffc09b3a5a [ 141.087241] PGD 8fe4c0d067 P4D 8fe4c0d067 PUD 8fe4c0f067 PMD 103ad89067 PTE 0 [ 141.087464] Oops: 0010 [#1] SMP NOPTI [ 141.087580] CPU: 67 PID: 668 Comm: kworker/67:1 Kdump: loaded Not tainted 4.18.0.x86_64 #47 [ 141.088009] Workqueue: events 0xffffffffc09b3a40 [ 141.088009] RIP: 0010:0xffffffffc09b3a5a [ 141.088009] Code: Bad RIP value. [ 141.088009] RSP: 0018:ffffb9094e2c3e88 EFLAGS: 00010246 [ 141.088009] RAX: 0000000000000000 RBX: ffff9abfdb1f04a0 RCX: 0000000000000000 [ 141.088009] RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000246 [ 141.088009] RBP: 0000000000000000 R08: ffff9abfffee3cb8 R09: 00000000000002e1 [ 141.088009] R10: ffffb9094cb73d90 R11: 00000000000f4240 R12: ffff9abfffee8700 [ 141.088009] R13: 0000000000000000 R14: ffff9abfdb1f04a0 R15: ffff9abfdb1f04a8 [ 141.088009] FS: 0000000000000000(0000) GS:ffff9abfffec0000(0000) knlGS:0000000000000000 [ 141.088009] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 141.088009] CR2: ffffffffc09b3a30 CR3: 0000008fe4c0a001 CR4: 00000000007606e0 [ 141.088009] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 141.088009] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 141.088009] PKRU: 55555554 [ 141.088009] Call Trace: [ 141.088009] ? process_one_work+0x195/0x390 [ 141.088009] ? worker_thread+0x30/0x390 [ 141.088009] ? process_one_work+0x390/0x390 [ 141.088009] ? kthread+0x10d/0x130 [ 141.088009] ? kthread_flush_work_fn+0x10/0x10 [ 141.088009] ? ret_from_fork+0x35/0x40] BUG: unable to handle kernel paging request at ffffffffc0b28a5a [ 200.223240] PGD 97fe00d067 P4D 97fe00d067 PUD 97fe00f067 PMD a580cbf067 PTE 0 [ 200.223464] Oops: 0010 [#1] SMP NOPTI [ 200.223579] CPU: 63 PID: 664 Comm: kworker/63:1 Kdump: loaded Not tainted 4.18.0.x86_64 #46 [ 200.224008] Workqueue: events 0xffffffffc0b28a40 [ 200.224008] RIP: 0010:0xffffffffc0b28a5a [ 200.224008] Code: Bad RIP value. [ 200.224008] RSP: 0018:ffffbf3c8e2a3e88 EFLAGS: 00010246 [ 200.224008] RAX: 0000000000000000 RBX: ffffa0799ad6bca0 RCX: 0000000000000000 [ 200.224008] RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000246 [ 200.224008] RBP: 0000000000000000 R08: ffff9fe43fde3cb8 R09: 00000000000000d5 [ 200.224008] R10: ffffbf3c8cb53d90 R11: 00000000000f4240 R12: ffff9fe43fde8700 [ 200.224008] R13: 0000000000000000 R14: ffffa0799ad6bca0 R15: ffffa0799ad6bca8 [ 200.224008] FS: 0000000000000000(0000) GS:ffff9fe43fdc0000(0000) knlGS:0000000000000000 [ 200.224008] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 200.224008] CR2: ffffffffc0b28a30 CR3: 00000097fe00a002 CR4: 00000000007606e0 [ 200.224008] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 200.224008] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 200.224008] PKRU: 55555554 [ 200.224008] Call Trace: [ 200.224008] ? process_one_work+0x195/0x390 [ 200.224008] ? worker_thread+0x30/0x390 [ 200.224008] ? process_one_work+0x390/0x390 [ 200.224008] ? kthread+0x10d/0x130 [ 200.224008] ? kthread_flush_work_fn+0x10/0x10 [ 200.224008] ? ret_from_fork+0x35/0x40 [ 200.224008] kernel fault(0x1) notification starting on CPU 63 [ 200.224008] kernel fault(0x1) notification finished on CPU 63 [ 200.224008] CR2: ffffffffc0b28a5a [ 200.224008] ---[ end trace c82a412d93f57412 ]--- The reason is as follows: T1: rmmod ipmi_si. ->ipmi_unregister_smi() -> ipmi_bmc_unregister() -> __ipmi_bmc_unregister() -> kref_put(&bmc->usecount, cleanup_bmc_device); -> schedule_work(&bmc->remove_work); T2: rmmod ipmi_msghandl ---truncated---

IBM Common Cryptographic Architecture (CCA 5.x MTM for 4767 and CCA 7.x MTM for 4769) could allow a local user to cause a denial of service due to improper input validation. IBM X-Force ID: 223596.

In the Linux kernel, the following vulnerability has been resolved: sysctl: Fix out of bounds access for empty sysctl registers When registering tables to the sysctl subsystem there is a check to see if header is a permanently empty directory (used for mounts). This check evaluates the first element of the ctl_table. This results in an out of bounds evaluation when registering empty directories. The function register_sysctl_mount_point now passes a ctl_table of size 1 instead of size 0. It now relies solely on the type to identify a permanently empty register. Make sure that the ctl_table has at least one element before testing for permanent emptiness.

In the Linux kernel, the following vulnerability has been resolved: binder: fix memleak of proc->delivered_freeze If a freeze notification is cleared with BC_CLEAR_FREEZE_NOTIFICATION before calling binder_freeze_notification_done(), then it is detached from its reference (e.g. ref->freeze) but the work remains queued in proc->delivered_freeze. This leads to a memory leak when the process exits as any pending entries in proc->delivered_freeze are not freed: unreferenced object 0xffff38e8cfa36180 (size 64): comm "binder-util", pid 655, jiffies 4294936641 hex dump (first 32 bytes): b8 e9 9e c8 e8 38 ff ff b8 e9 9e c8 e8 38 ff ff .....8.......8.. 0b 00 00 00 00 00 00 00 3c 1f 4b 00 00 00 00 00 ........<.K..... backtrace (crc 95983b32): [<000000000d0582cf>] kmemleak_alloc+0x34/0x40 [<000000009c99a513>] __kmalloc_cache_noprof+0x208/0x280 [<00000000313b1704>] binder_thread_write+0xdec/0x439c [<000000000cbd33bb>] binder_ioctl+0x1b68/0x22cc [<000000002bbedeeb>] __arm64_sys_ioctl+0x124/0x190 [<00000000b439adee>] invoke_syscall+0x6c/0x254 [<00000000173558fc>] el0_svc_common.constprop.0+0xac/0x230 [<0000000084f72311>] do_el0_svc+0x40/0x58 [<000000008b872457>] el0_svc+0x38/0x78 [<00000000ee778653>] el0t_64_sync_handler+0x120/0x12c [<00000000a8ec61bf>] el0t_64_sync+0x190/0x194 This patch fixes the leak by ensuring that any pending entries in proc->delivered_freeze are freed during binder_deferred_release().

A flaw was found in the Linux kernel’s KVM when attempting to set a SynIC IRQ. This issue makes it possible for a misbehaving VMM to write to SYNIC/STIMER MSRs, causing a NULL pointer dereference. This flaw allows an unprivileged local attacker on the host to issue specific ioctl calls, causing a kernel oops condition that results in a denial of service.

In the Linux kernel before 6.5.9, there is a NULL pointer dereference in send_acknowledge in net/nfc/nci/spi.c.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Assign normalized_pix_clk when color depth = 14 [WHY & HOW] A warning message "WARNING: CPU: 4 PID: 459 at ... /dc_resource.c:3397 calculate_phy_pix_clks+0xef/0x100 [amdgpu]" occurs because the display_color_depth == COLOR_DEPTH_141414 is not handled. This is observed in Radeon RX 6600 XT. It is fixed by assigning pix_clk * (14 * 3) / 24 - same as the rests. Also fixes the indentation in get_norm_pix_clk. (cherry picked from commit 274a87eb389f58eddcbc5659ab0b180b37e92775)

In the Linux kernel, the following vulnerability has been resolved: powerpc/47x: Fix 47x syscall return crash Eddie reported that newer kernels were crashing during boot on his 476 FSP2 system: kernel tried to execute user page (b7ee2000) - exploit attempt? (uid: 0) BUG: Unable to handle kernel instruction fetch Faulting instruction address: 0xb7ee2000 Oops: Kernel access of bad area, sig: 11 [#1] BE PAGE_SIZE=4K FSP-2 Modules linked in: CPU: 0 PID: 61 Comm: mount Not tainted 6.1.55-d23900f.ppcnf-fsp2 #1 Hardware name: ibm,fsp2 476fpe 0x7ff520c0 FSP-2 NIP:  b7ee2000 LR: 8c008000 CTR: 00000000 REGS: bffebd83 TRAP: 0400   Not tainted (6.1.55-d23900f.ppcnf-fs p2) MSR:  00000030 <IR,DR>  CR: 00001000  XER: 20000000 GPR00: c00110ac bffebe63 bffebe7e bffebe88 8c008000 00001000 00000d12 b7ee2000 GPR08: 00000033 00000000 00000000 c139df10 48224824 1016c314 10160000 00000000 GPR16: 10160000 10160000 00000008 00000000 10160000 00000000 10160000 1017f5b0 GPR24: 1017fa50 1017f4f0 1017fa50 1017f740 1017f630 00000000 00000000 1017f4f0 NIP [b7ee2000] 0xb7ee2000 LR [8c008000] 0x8c008000 Call Trace: Instruction dump: XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX ---[ end trace 0000000000000000 ]--- The problem is in ret_from_syscall where the check for icache_44x_need_flush is done. When the flush is needed the code jumps out-of-line to do the flush, and then intends to jump back to continue the syscall return. However the branch back to label 1b doesn't return to the correct location, instead branching back just prior to the return to userspace, causing bogus register values to be used by the rfi. The breakage was introduced by commit 6f76a01173cc ("powerpc/syscall: implement system call entry/exit logic in C for PPC32") which inadvertently removed the "1" label and reused it elsewhere. Fix it by adding named local labels in the correct locations. Note that the return label needs to be outside the ifdef so that CONFIG_PPC_47x=n compiles.

A vulnerability was found in the Linux kernel's nft_set_desc_concat_parse() function .This flaw allows an attacker to trigger a buffer overflow via nft_set_desc_concat_parse() , causing a denial of service and possibly to run code.

In the Linux kernel, the following vulnerability has been resolved: scsi: core: Fix error handling of scsi_host_alloc() After device is initialized via device_initialize(), or its name is set via dev_set_name(), the device has to be freed via put_device(). Otherwise device name will be leaked because it is allocated dynamically in dev_set_name(). Fix the leak by replacing kfree() with put_device(). Since scsi_host_dev_release() properly handles IDA and kthread removal, remove special-casing these from the error handling as well.

In the Linux kernel, the following vulnerability has been resolved: mt76: mt7921: fix possible invalid register access Disable the interrupt and synchronze for the pending irq handlers to ensure the irq tasklet is not being scheduled after the suspend to avoid the possible invalid register access acts when the host pcie controller is suspended. [17932.910534] mt7921e 0000:01:00.0: pci_pm_suspend+0x0/0x22c returned 0 after 21375 usecs [17932.910590] pcieport 0000:00:00.0: calling pci_pm_suspend+0x0/0x22c @ 18565, parent: pci0000:00 [17932.910602] pcieport 0000:00:00.0: pci_pm_suspend+0x0/0x22c returned 0 after 8 usecs [17932.910671] mtk-pcie 11230000.pcie: calling platform_pm_suspend+0x0/0x60 @ 22783, parent: soc [17932.910674] mtk-pcie 11230000.pcie: platform_pm_suspend+0x0/0x60 returned 0 after 0 usecs ... 17933.615352] x1 : 00000000000d4200 x0 : ffffff8269ca2300 [17933.620666] Call trace: [17933.623127] mt76_mmio_rr+0x28/0xf0 [mt76] [17933.627234] mt7921_rr+0x38/0x44 [mt7921e] [17933.631339] mt7921_irq_tasklet+0x54/0x1d8 [mt7921e] [17933.636309] tasklet_action_common+0x12c/0x16c [17933.640754] tasklet_action+0x24/0x2c [17933.644418] __do_softirq+0x16c/0x344 [17933.648082] irq_exit+0xa8/0xac [17933.651224] scheduler_ipi+0xd4/0x148 [17933.654890] handle_IPI+0x164/0x2d4 [17933.658379] gic_handle_irq+0x140/0x178 [17933.662216] el1_irq+0xb8/0x180 [17933.665361] cpuidle_enter_state+0xf8/0x204 [17933.669544] cpuidle_enter+0x38/0x4c [17933.673122] do_idle+0x1a4/0x2a8 [17933.676352] cpu_startup_entry+0x24/0x28 [17933.680276] rest_init+0xd4/0xe0 [17933.683508] arch_call_rest_init+0x10/0x18 [17933.687606] start_kernel+0x340/0x3b4 [17933.691279] Code: aa0003f5 d503201f f953eaa8 8b344108 (b9400113) [17933.697373] ---[ end trace a24b8e26ffbda3c5 ]--- [17933.767846] Kernel panic - not syncing: Fatal exception in interrupt

In the Linux kernel, the following vulnerability has been resolved: drop_monitor: fix incorrect initialization order Syzkaller reports the following bug: BUG: spinlock bad magic on CPU#1, syz-executor.0/7995 lock: 0xffff88805303f3e0, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0 CPU: 1 PID: 7995 Comm: syz-executor.0 Tainted: G E 5.10.209+ #1 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 11/12/2020 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x119/0x179 lib/dump_stack.c:118 debug_spin_lock_before kernel/locking/spinlock_debug.c:83 [inline] do_raw_spin_lock+0x1f6/0x270 kernel/locking/spinlock_debug.c:112 __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:117 [inline] _raw_spin_lock_irqsave+0x50/0x70 kernel/locking/spinlock.c:159 reset_per_cpu_data+0xe6/0x240 [drop_monitor] net_dm_cmd_trace+0x43d/0x17a0 [drop_monitor] genl_family_rcv_msg_doit+0x22f/0x330 net/netlink/genetlink.c:739 genl_family_rcv_msg net/netlink/genetlink.c:783 [inline] genl_rcv_msg+0x341/0x5a0 net/netlink/genetlink.c:800 netlink_rcv_skb+0x14d/0x440 net/netlink/af_netlink.c:2497 genl_rcv+0x29/0x40 net/netlink/genetlink.c:811 netlink_unicast_kernel net/netlink/af_netlink.c:1322 [inline] netlink_unicast+0x54b/0x800 net/netlink/af_netlink.c:1348 netlink_sendmsg+0x914/0xe00 net/netlink/af_netlink.c:1916 sock_sendmsg_nosec net/socket.c:651 [inline] __sock_sendmsg+0x157/0x190 net/socket.c:663 ____sys_sendmsg+0x712/0x870 net/socket.c:2378 ___sys_sendmsg+0xf8/0x170 net/socket.c:2432 __sys_sendmsg+0xea/0x1b0 net/socket.c:2461 do_syscall_64+0x30/0x40 arch/x86/entry/common.c:46 entry_SYSCALL_64_after_hwframe+0x62/0xc7 RIP: 0033:0x7f3f9815aee9 Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f3f972bf0c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f3f9826d050 RCX: 00007f3f9815aee9 RDX: 0000000020000000 RSI: 0000000020001300 RDI: 0000000000000007 RBP: 00007f3f981b63bd R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 000000000000006e R14: 00007f3f9826d050 R15: 00007ffe01ee6768 If drop_monitor is built as a kernel module, syzkaller may have time to send a netlink NET_DM_CMD_START message during the module loading. This will call the net_dm_monitor_start() function that uses a spinlock that has not yet been initialized. To fix this, let's place resource initialization above the registration of a generic netlink family. Found by InfoTeCS on behalf of Linux Verification Center (linuxtesting.org) with Syzkaller.

In the Linux kernel, the following vulnerability has been resolved: arm64/crc-t10dif: fix use of out-of-scope array in crc_t10dif_arch() Fix a silly bug where an array was used outside of its scope.

In the Linux kernel, the following vulnerability has been resolved: media: mediatek: vcodec: Fix a resource leak related to the scp device in FW initialization On Mediatek devices with a system companion processor (SCP) the mtk_scp structure has to be removed explicitly to avoid a resource leak. Free the structure in case the allocation of the firmware structure fails during the firmware initialization.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: Clear affinity hint before calling ath11k_pcic_free_irq() in error path If a shared IRQ is used by the driver due to platform limitation, then the IRQ affinity hint is set right after the allocation of IRQ vectors in ath11k_pci_alloc_msi(). This does no harm unless one of the functions requesting the IRQ fails and attempt to free the IRQ. This results in the below warning: WARNING: CPU: 7 PID: 349 at kernel/irq/manage.c:1929 free_irq+0x278/0x29c Call trace: free_irq+0x278/0x29c ath11k_pcic_free_irq+0x70/0x10c [ath11k] ath11k_pci_probe+0x800/0x820 [ath11k_pci] local_pci_probe+0x40/0xbc The warning is due to not clearing the affinity hint before freeing the IRQs. So to fix this issue, clear the IRQ affinity hint before calling ath11k_pcic_free_irq() in the error path. The affinity will be cleared once again further down the error path due to code organization, but that does no harm. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1

In the Linux kernel, the following vulnerability has been resolved: arm/crc-t10dif: fix use of out-of-scope array in crc_t10dif_arch() Fix a silly bug where an array was used outside of its scope.

In the Linux kernel, the following vulnerability has been resolved: md/raid1,raid10: don't ignore IO flags If blk-wbt is enabled by default, it's found that raid write performance is quite bad because all IO are throttled by wbt of underlying disks, due to flag REQ_IDLE is ignored. And turns out this behaviour exist since blk-wbt is introduced. Other than REQ_IDLE, other flags should not be ignored as well, for example REQ_META can be set for filesystems, clearing it can cause priority reverse problems; And REQ_NOWAIT should not be cleared as well, because io will wait instead of failing directly in underlying disks. Fix those problems by keep IO flags from master bio. Fises: f51d46d0e7cb ("md: add support for REQ_NOWAIT")

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Clear affinity hint before calling ath12k_pci_free_irq() in error path If a shared IRQ is used by the driver due to platform limitation, then the IRQ affinity hint is set right after the allocation of IRQ vectors in ath12k_pci_msi_alloc(). This does no harm unless one of the functions requesting the IRQ fails and attempt to free the IRQ. This may end up with a warning from the IRQ core that is expecting the affinity hint to be cleared before freeing the IRQ: kernel/irq/manage.c: /* make sure affinity_hint is cleaned up */ if (WARN_ON_ONCE(desc->affinity_hint)) desc->affinity_hint = NULL; So to fix this issue, clear the IRQ affinity hint before calling ath12k_pci_free_irq() in the error path. The affinity will be cleared once again further down the error path due to code organization, but that does no harm.

In the Linux kernel, the following vulnerability has been resolved: md/md-bitmap: fix wrong bitmap_limit for clustermd when write sb In clustermd, separate write-intent-bitmaps are used for each cluster node: 0 4k 8k 12k ------------------------------------------------------------------- | idle | md super | bm super [0] + bits | | bm bits[0, contd] | bm super[1] + bits | bm bits[1, contd] | | bm super[2] + bits | bm bits [2, contd] | bm super[3] + bits | | bm bits [3, contd] | | | So in node 1, pg_index in __write_sb_page() could equal to bitmap->storage.file_pages. Then bitmap_limit will be calculated to 0. md_super_write() will be called with 0 size. That means the first 4k sb area of node 1 will never be updated through filemap_write_page(). This bug causes hang of mdadm/clustermd_tests/01r1_Grow_resize. Here use (pg_index % bitmap->storage.file_pages) to make calculation of bitmap_limit correct.

In the Linux kernel, the following vulnerability has been resolved: block: Fix WARNING in _copy_from_iter Syzkaller reports a warning in _copy_from_iter because an iov_iter is supposedly used in the wrong direction. The reason is that syzcaller managed to generate a request with a transfer direction of SG_DXFER_TO_FROM_DEV. This instructs the kernel to copy user buffers into the kernel, read into the copied buffers and then copy the data back to user space. Thus the iovec is used in both directions. Detect this situation in the block layer and construct a new iterator with the correct direction for the copy-in.

In the Linux kernel, the following vulnerability has been resolved: io_uring/net: fix io_req_post_cqe abuse by send bundle [ 114.987980][ T5313] WARNING: CPU: 6 PID: 5313 at io_uring/io_uring.c:872 io_req_post_cqe+0x12e/0x4f0 [ 114.991597][ T5313] RIP: 0010:io_req_post_cqe+0x12e/0x4f0 [ 115.001880][ T5313] Call Trace: [ 115.002222][ T5313] <TASK> [ 115.007813][ T5313] io_send+0x4fe/0x10f0 [ 115.009317][ T5313] io_issue_sqe+0x1a6/0x1740 [ 115.012094][ T5313] io_wq_submit_work+0x38b/0xed0 [ 115.013223][ T5313] io_worker_handle_work+0x62a/0x1600 [ 115.013876][ T5313] io_wq_worker+0x34f/0xdf0 As the comment states, io_req_post_cqe() should only be used by multishot requests, i.e. REQ_F_APOLL_MULTISHOT, which bundled sends are not. Add a flag signifying whether a request wants to post multiple CQEs. Eventually REQ_F_APOLL_MULTISHOT should imply the new flag, but that's left out for simplicity.

A NULL pointer dereference issue was found in KVM when releasing a vCPU with dirty ring support enabled. This flaw allows an unprivileged local attacker on the host to issue specific ioctl calls, causing a kernel oops condition that results in a denial of service.

In the Linux kernel, the following vulnerability has been resolved: sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues efx->xdp_tx_queue_count is initially initialized to num_possible_cpus() and is later used to allocate and traverse efx->xdp_tx_queues lookup array. However, we may end up not initializing all the array slots with real queues during probing. This results, for example, in a NULL pointer dereference, when running "# ethtool -S <iface>", similar to below [2570283.664955][T4126959] BUG: kernel NULL pointer dereference, address: 00000000000000f8 [2570283.681283][T4126959] #PF: supervisor read access in kernel mode [2570283.695678][T4126959] #PF: error_code(0x0000) - not-present page [2570283.710013][T4126959] PGD 0 P4D 0 [2570283.721649][T4126959] Oops: 0000 [#1] SMP PTI [2570283.734108][T4126959] CPU: 23 PID: 4126959 Comm: ethtool Tainted: G O 5.10.20-cloudflare-2021.3.1 #1 [2570283.752641][T4126959] Hardware name: <redacted> [2570283.781408][T4126959] RIP: 0010:efx_ethtool_get_stats+0x2ca/0x330 [sfc] [2570283.796073][T4126959] Code: 00 85 c0 74 39 48 8b 95 a8 0f 00 00 48 85 d2 74 2d 31 c0 eb 07 48 8b 95 a8 0f 00 00 48 63 c8 49 83 c4 08 83 c0 01 48 8b 14 ca <48> 8b 92 f8 00 00 00 49 89 54 24 f8 39 85 a0 0f 00 00 77 d7 48 8b [2570283.831259][T4126959] RSP: 0018:ffffb79a77657ce8 EFLAGS: 00010202 [2570283.845121][T4126959] RAX: 0000000000000019 RBX: ffffb799cd0c9280 RCX: 0000000000000018 [2570283.860872][T4126959] RDX: 0000000000000000 RSI: ffff96dd970ce000 RDI: 0000000000000005 [2570283.876525][T4126959] RBP: ffff96dd86f0a000 R08: ffff96dd970ce480 R09: 000000000000005f [2570283.892014][T4126959] R10: ffffb799cd0c9fff R11: ffffb799cd0c9000 R12: ffffb799cd0c94f8 [2570283.907406][T4126959] R13: ffffffffc11b1090 R14: ffff96dd970ce000 R15: ffffffffc11cd66c [2570283.922705][T4126959] FS: 00007fa7723f8740(0000) GS:ffff96f51fac0000(0000) knlGS:0000000000000000 [2570283.938848][T4126959] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [2570283.952524][T4126959] CR2: 00000000000000f8 CR3: 0000001a73e6e006 CR4: 00000000007706e0 [2570283.967529][T4126959] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [2570283.982400][T4126959] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [2570283.997308][T4126959] PKRU: 55555554 [2570284.007649][T4126959] Call Trace: [2570284.017598][T4126959] dev_ethtool+0x1832/0x2830 Fix this by adjusting efx->xdp_tx_queue_count after probing to reflect the true value of initialized slots in efx->xdp_tx_queues.

A flaw was found in the filelock_init in fs/locks.c function in the Linux kernel. This issue can lead to host memory exhaustion due to memcg not limiting the number of Portable Operating System Interface (POSIX) file locks.

A flaw null pointer dereference in the Linux kernel UDF file system functionality was found in the way user triggers udf_file_write_iter function for the malicious UDF image. A local user could use this flaw to crash the system. Actual from Linux kernel 4.2-rc1 till 5.17-rc2.

In the Linux kernel, the following vulnerability has been resolved: net: ipv6: fix dst ref loops in rpl, seg6 and ioam6 lwtunnels Some lwtunnels have a dst cache for post-transformation dst. If the packet destination did not change we may end up recording a reference to the lwtunnel in its own cache, and the lwtunnel state will never be freed. Discovered by the ioam6.sh test, kmemleak was recently fixed to catch per-cpu memory leaks. I'm not sure if rpl and seg6 can actually hit this, but in principle I don't see why not.

A use-after-free vulnerability was found in the Linux kernel in drivers/net/hamradio. This flaw allows a local attacker with a user privilege to cause a denial of service (DOS) when the mkiss or sixpack device is detached and reclaim resources early.

In the Linux kernel, the following vulnerability has been resolved: amdkfd: properly free gang_ctx_bo when failed to init user queue The destructor of a gtt bo is declared as void amdgpu_amdkfd_free_gtt_mem(struct amdgpu_device *adev, void **mem_obj); Which takes void** as the second parameter. GCC allows passing void* to the function because void* can be implicitly casted to any other types, so it can pass compiling. However, passing this void* parameter into the function's execution process(which expects void** and dereferencing void**) will result in errors.