In the Linux kernel, the following vulnerability has been resolved: sctp: do asoc update earlier in sctp_sf_do_dupcook_a There's a panic that occurs in a few of envs, the call trace is as below: [] general protection fault, ... 0x29acd70f1000a: 0000 [#1] SMP PTI [] RIP: 0010:sctp_ulpevent_notify_peer_addr_change+0x4b/0x1fa [sctp] [] sctp_assoc_control_transport+0x1b9/0x210 [sctp] [] sctp_do_8_2_transport_strike.isra.16+0x15c/0x220 [sctp] [] sctp_cmd_interpreter.isra.21+0x1231/0x1a10 [sctp] [] sctp_do_sm+0xc3/0x2a0 [sctp] [] sctp_generate_timeout_event+0x81/0xf0 [sctp] This is caused by a transport use-after-free issue. When processing a duplicate COOKIE-ECHO chunk in sctp_sf_do_dupcook_a(), both COOKIE-ACK and SHUTDOWN chunks are allocated with the transort from the new asoc. However, later in the sideeffect machine, the old asoc is used to send them out and old asoc's shutdown_last_sent_to is set to the transport that SHUTDOWN chunk attached to in sctp_cmd_setup_t2(), which actually belongs to the new asoc. After the new_asoc is freed and the old asoc T2 timeout, the old asoc's shutdown_last_sent_to that is already freed would be accessed in sctp_sf_t2_timer_expire(). Thanks Alexander and Jere for helping dig into this issue. To fix it, this patch is to do the asoc update first, then allocate the COOKIE-ACK and SHUTDOWN chunks with the 'updated' old asoc. This would make more sense, as a chunk from an asoc shouldn't be sent out with another asoc. We had fixed quite a few issues caused by this.

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix race between transaction aborts and fsyncs leading to use-after-free There is a race between a task aborting a transaction during a commit, a task doing an fsync and the transaction kthread, which leads to an use-after-free of the log root tree. When this happens, it results in a stack trace like the following: BTRFS info (device dm-0): forced readonly BTRFS warning (device dm-0): Skipping commit of aborted transaction. BTRFS: error (device dm-0) in cleanup_transaction:1958: errno=-5 IO failure BTRFS warning (device dm-0): lost page write due to IO error on /dev/mapper/error-test (-5) BTRFS warning (device dm-0): Skipping commit of aborted transaction. BTRFS warning (device dm-0): direct IO failed ino 261 rw 0,0 sector 0xa4e8 len 4096 err no 10 BTRFS error (device dm-0): error writing primary super block to device 1 BTRFS warning (device dm-0): direct IO failed ino 261 rw 0,0 sector 0x12e000 len 4096 err no 10 BTRFS warning (device dm-0): direct IO failed ino 261 rw 0,0 sector 0x12e008 len 4096 err no 10 BTRFS warning (device dm-0): direct IO failed ino 261 rw 0,0 sector 0x12e010 len 4096 err no 10 BTRFS: error (device dm-0) in write_all_supers:4110: errno=-5 IO failure (1 errors while writing supers) BTRFS: error (device dm-0) in btrfs_sync_log:3308: errno=-5 IO failure general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b68: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC PTI CPU: 2 PID: 2458471 Comm: fsstress Not tainted 5.12.0-rc5-btrfs-next-84 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 RIP: 0010:__mutex_lock+0x139/0xa40 Code: c0 74 19 (...) RSP: 0018:ffff9f18830d7b00 EFLAGS: 00010202 RAX: 6b6b6b6b6b6b6b68 RBX: 0000000000000001 RCX: 0000000000000002 RDX: ffffffffb9c54d13 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffff9f18830d7bc0 R08: 0000000000000000 R09: 0000000000000000 R10: ffff9f18830d7be0 R11: 0000000000000001 R12: ffff8c6cd199c040 R13: ffff8c6c95821358 R14: 00000000fffffffb R15: ffff8c6cbcf01358 FS: 00007fa9140c2b80(0000) GS:ffff8c6fac600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fa913d52000 CR3: 000000013d2b4003 CR4: 0000000000370ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: ? __btrfs_handle_fs_error+0xde/0x146 [btrfs] ? btrfs_sync_log+0x7c1/0xf20 [btrfs] ? btrfs_sync_log+0x7c1/0xf20 [btrfs] btrfs_sync_log+0x7c1/0xf20 [btrfs] btrfs_sync_file+0x40c/0x580 [btrfs] do_fsync+0x38/0x70 __x64_sys_fsync+0x10/0x20 do_syscall_64+0x33/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7fa9142a55c3 Code: 8b 15 09 (...) RSP: 002b:00007fff26278d48 EFLAGS: 00000246 ORIG_RAX: 000000000000004a RAX: ffffffffffffffda RBX: 0000563c83cb4560 RCX: 00007fa9142a55c3 RDX: 00007fff26278cb0 RSI: 00007fff26278cb0 RDI: 0000000000000005 RBP: 0000000000000005 R08: 0000000000000001 R09: 00007fff26278d5c R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000340 R13: 00007fff26278de0 R14: 00007fff26278d96 R15: 0000563c83ca57c0 Modules linked in: btrfs dm_zero dm_snapshot dm_thin_pool (...) ---[ end trace ee2f1b19327d791d ]--- The steps that lead to this crash are the following: 1) We are at transaction N; 2) We have two tasks with a transaction handle attached to transaction N. Task A and Task B. Task B is doing an fsync; 3) Task B is at btrfs_sync_log(), and has saved fs_info->log_root_tree into a local variable named 'log_root_tree' at the top of btrfs_sync_log(). Task B is about to call write_all_supers(), but before that... 4) Task A calls btrfs_commit_transaction(), and after it sets the transaction state to TRANS_STATE_COMMIT_START, an error happens before it w ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net: fix use-after-free in tw_timer_handler A real world panic issue was found as follow in Linux 5.4. BUG: unable to handle page fault for address: ffffde49a863de28 PGD 7e6fe62067 P4D 7e6fe62067 PUD 7e6fe63067 PMD f51e064067 PTE 0 RIP: 0010:tw_timer_handler+0x20/0x40 Call Trace: <IRQ> call_timer_fn+0x2b/0x120 run_timer_softirq+0x1ef/0x450 __do_softirq+0x10d/0x2b8 irq_exit+0xc7/0xd0 smp_apic_timer_interrupt+0x68/0x120 apic_timer_interrupt+0xf/0x20 This issue was also reported since 2017 in the thread [1], unfortunately, the issue was still can be reproduced after fixing DCCP. The ipv4_mib_exit_net is called before tcp_sk_exit_batch when a net namespace is destroyed since tcp_sk_ops is registered befrore ipv4_mib_ops, which means tcp_sk_ops is in the front of ipv4_mib_ops in the list of pernet_list. There will be a use-after-free on net->mib.net_statistics in tw_timer_handler after ipv4_mib_exit_net if there are some inflight time-wait timers. This bug is not introduced by commit f2bf415cfed7 ("mib: add net to NET_ADD_STATS_BH") since the net_statistics is a global variable instead of dynamic allocation and freeing. Actually, commit 61a7e26028b9 ("mib: put net statistics on struct net") introduces the bug since it put net statistics on struct net and free it when net namespace is destroyed. Moving init_ipv4_mibs() to the front of tcp_init() to fix this bug and replace pr_crit() with panic() since continuing is meaningless when init_ipv4_mibs() fails. [1] https://groups.google.com/g/syzkaller/c/p1tn-_Kc6l4/m/smuL_FMAAgAJ?pli=1

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: fix use-after-free in nft_set_catchall_destroy() We need to use list_for_each_entry_safe() iterator because we can not access @catchall after kfree_rcu() call. syzbot reported: BUG: KASAN: use-after-free in nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline] BUG: KASAN: use-after-free in nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline] BUG: KASAN: use-after-free in nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493 Read of size 8 at addr ffff8880716e5b80 by task syz-executor.3/8871 CPU: 1 PID: 8871 Comm: syz-executor.3 Not tainted 5.16.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_address_description.constprop.0.cold+0x8d/0x2ed mm/kasan/report.c:247 __kasan_report mm/kasan/report.c:433 [inline] kasan_report.cold+0x83/0xdf mm/kasan/report.c:450 nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline] nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline] nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493 __nft_release_table+0x79f/0xcd0 net/netfilter/nf_tables_api.c:9626 nft_rcv_nl_event+0x4f8/0x670 net/netfilter/nf_tables_api.c:9688 notifier_call_chain+0xb5/0x200 kernel/notifier.c:83 blocking_notifier_call_chain kernel/notifier.c:318 [inline] blocking_notifier_call_chain+0x67/0x90 kernel/notifier.c:306 netlink_release+0xcb6/0x1dd0 net/netlink/af_netlink.c:788 __sock_release+0xcd/0x280 net/socket.c:649 sock_close+0x18/0x20 net/socket.c:1314 __fput+0x286/0x9f0 fs/file_table.c:280 task_work_run+0xdd/0x1a0 kernel/task_work.c:164 tracehook_notify_resume include/linux/tracehook.h:189 [inline] exit_to_user_mode_loop kernel/entry/common.c:175 [inline] exit_to_user_mode_prepare+0x27e/0x290 kernel/entry/common.c:207 __syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline] syscall_exit_to_user_mode+0x19/0x60 kernel/entry/common.c:300 do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f75fbf28adb Code: 0f 05 48 3d 00 f0 ff ff 77 45 c3 0f 1f 40 00 48 83 ec 18 89 7c 24 0c e8 63 fc ff ff 8b 7c 24 0c 41 89 c0 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 35 44 89 c7 89 44 24 0c e8 a1 fc ff ff 8b 44 RSP: 002b:00007ffd8da7ec10 EFLAGS: 00000293 ORIG_RAX: 0000000000000003 RAX: 0000000000000000 RBX: 0000000000000004 RCX: 00007f75fbf28adb RDX: 00007f75fc08e828 RSI: ffffffffffffffff RDI: 0000000000000003 RBP: 00007f75fc08a960 R08: 0000000000000000 R09: 00007f75fc08e830 R10: 00007ffd8da7ed10 R11: 0000000000000293 R12: 00000000002067c3 R13: 00007ffd8da7ed10 R14: 00007f75fc088f60 R15: 0000000000000032 </TASK> Allocated by task 8886: kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38 kasan_set_track mm/kasan/common.c:46 [inline] set_alloc_info mm/kasan/common.c:434 [inline] ____kasan_kmalloc mm/kasan/common.c:513 [inline] ____kasan_kmalloc mm/kasan/common.c:472 [inline] __kasan_kmalloc+0xa6/0xd0 mm/kasan/common.c:522 kasan_kmalloc include/linux/kasan.h:269 [inline] kmem_cache_alloc_trace+0x1ea/0x4a0 mm/slab.c:3575 kmalloc include/linux/slab.h:590 [inline] nft_setelem_catchall_insert net/netfilter/nf_tables_api.c:5544 [inline] nft_setelem_insert net/netfilter/nf_tables_api.c:5562 [inline] nft_add_set_elem+0x232e/0x2f40 net/netfilter/nf_tables_api.c:5936 nf_tables_newsetelem+0x6ff/0xbb0 net/netfilter/nf_tables_api.c:6032 nfnetlink_rcv_batch+0x1710/0x25f0 net/netfilter/nfnetlink.c:513 nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline] nfnetlink_rcv+0x3af/0x420 net/netfilter/nfnetlink.c:652 netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline] netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1345 netlink_sendmsg+0x904/0xdf0 net/netlink/af_netlink.c:1921 sock_sendmsg_nosec net/ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: sata_fsl: fix UAF in sata_fsl_port_stop when rmmod sata_fsl When the `rmmod sata_fsl.ko` command is executed in the PPC64 GNU/Linux, a bug is reported: ================================================================== BUG: Unable to handle kernel data access on read at 0x80000800805b502c Oops: Kernel access of bad area, sig: 11 [#1] NIP [c0000000000388a4] .ioread32+0x4/0x20 LR [80000000000c6034] .sata_fsl_port_stop+0x44/0xe0 [sata_fsl] Call Trace: .free_irq+0x1c/0x4e0 (unreliable) .ata_host_stop+0x74/0xd0 [libata] .release_nodes+0x330/0x3f0 .device_release_driver_internal+0x178/0x2c0 .driver_detach+0x64/0xd0 .bus_remove_driver+0x70/0xf0 .driver_unregister+0x38/0x80 .platform_driver_unregister+0x14/0x30 .fsl_sata_driver_exit+0x18/0xa20 [sata_fsl] .__se_sys_delete_module+0x1ec/0x2d0 .system_call_exception+0xfc/0x1f0 system_call_common+0xf8/0x200 ================================================================== The triggering of the BUG is shown in the following stack: driver_detach device_release_driver_internal __device_release_driver drv->remove(dev) --> platform_drv_remove/platform_remove drv->remove(dev) --> sata_fsl_remove iounmap(host_priv->hcr_base); <---- unmap kfree(host_priv); <---- free devres_release_all release_nodes dr->node.release(dev, dr->data) --> ata_host_stop ap->ops->port_stop(ap) --> sata_fsl_port_stop ioread32(hcr_base + HCONTROL) <---- UAF host->ops->host_stop(host) The iounmap(host_priv->hcr_base) and kfree(host_priv) functions should not be executed in drv->remove. These functions should be executed in host_stop after port_stop. Therefore, we move these functions to the new function sata_fsl_host_stop and bind the new function to host_stop.

In the Linux kernel, the following vulnerability has been resolved: xen-netback: take a reference to the RX task thread Do this in order to prevent the task from being freed if the thread returns (which can be triggered by the frontend) before the call to kthread_stop done as part of the backend tear down. Not taking the reference will lead to a use-after-free in that scenario. Such reference was taken before but dropped as part of the rework done in 2ac061ce97f4. Reintroduce the reference taking and add a comment this time explaining why it's needed. This is XSA-374 / CVE-2021-28691.

In the Linux kernel, the following vulnerability has been resolved: scsi: iscsi: Fix conn use after free during resets If we haven't done a unbind target call we can race where iscsi_conn_teardown wakes up the EH thread and then frees the conn while those threads are still accessing the conn ehwait. We can only do one TMF per session so this just moves the TMF fields from the conn to the session. We can then rely on the iscsi_session_teardown->iscsi_remove_session->__iscsi_unbind_session call to remove the target and it's devices, and know after that point there is no device or scsi-ml callout trying to access the session.

In the Linux kernel, the following vulnerability has been resolved: RDMA: Fix use-after-free in rxe_queue_cleanup On error handling path in rxe_qp_from_init() qp->sq.queue is freed and then rxe_create_qp() will drop last reference to this object. qp clean up function will try to free this queue one time and it causes UAF bug. Fix it by zeroing queue pointer after freeing queue in rxe_qp_from_init().

In the Linux kernel, the following vulnerability has been resolved: media: davinci: vpif: fix use-after-free on driver unbind The driver allocates and registers two platform device structures during probe, but the devices were never deregistered on driver unbind. This results in a use-after-free on driver unbind as the device structures were allocated using devres and would be freed by driver core when remove() returns. Fix this by adding the missing deregistration calls to the remove() callback and failing probe on registration errors. Note that the platform device structures must be freed using a proper release callback to avoid leaking associated resources like device names.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: fix potential use-after-free in ec_bhf_remove static void ec_bhf_remove(struct pci_dev *dev) { ... struct ec_bhf_priv *priv = netdev_priv(net_dev); unregister_netdev(net_dev); free_netdev(net_dev); pci_iounmap(dev, priv->dma_io); pci_iounmap(dev, priv->io); ... } priv is netdev private data, but it is used after free_netdev(). It can cause use-after-free when accessing priv pointer. So, fix it by moving free_netdev() after pci_iounmap() calls.

In the Linux kernel, the following vulnerability has been resolved: net: qcom/emac: fix UAF in emac_remove adpt is netdev private data and it cannot be used after free_netdev() call. Using adpt after free_netdev() can cause UAF bug. Fix it by moving free_netdev() at the end of the function.

In the Linux kernel, the following vulnerability has been resolved: inet: fully convert sk->sk_rx_dst to RCU rules syzbot reported various issues around early demux, one being included in this changelog [1] sk->sk_rx_dst is using RCU protection without clearly documenting it. And following sequences in tcp_v4_do_rcv()/tcp_v6_do_rcv() are not following standard RCU rules. [a] dst_release(dst); [b] sk->sk_rx_dst = NULL; They look wrong because a delete operation of RCU protected pointer is supposed to clear the pointer before the call_rcu()/synchronize_rcu() guarding actual memory freeing. In some cases indeed, dst could be freed before [b] is done. We could cheat by clearing sk_rx_dst before calling dst_release(), but this seems the right time to stick to standard RCU annotations and debugging facilities. [1] BUG: KASAN: use-after-free in dst_check include/net/dst.h:470 [inline] BUG: KASAN: use-after-free in tcp_v4_early_demux+0x95b/0x960 net/ipv4/tcp_ipv4.c:1792 Read of size 2 at addr ffff88807f1cb73a by task syz-executor.5/9204 CPU: 0 PID: 9204 Comm: syz-executor.5 Not tainted 5.16.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_address_description.constprop.0.cold+0x8d/0x320 mm/kasan/report.c:247 __kasan_report mm/kasan/report.c:433 [inline] kasan_report.cold+0x83/0xdf mm/kasan/report.c:450 dst_check include/net/dst.h:470 [inline] tcp_v4_early_demux+0x95b/0x960 net/ipv4/tcp_ipv4.c:1792 ip_rcv_finish_core.constprop.0+0x15de/0x1e80 net/ipv4/ip_input.c:340 ip_list_rcv_finish.constprop.0+0x1b2/0x6e0 net/ipv4/ip_input.c:583 ip_sublist_rcv net/ipv4/ip_input.c:609 [inline] ip_list_rcv+0x34e/0x490 net/ipv4/ip_input.c:644 __netif_receive_skb_list_ptype net/core/dev.c:5508 [inline] __netif_receive_skb_list_core+0x549/0x8e0 net/core/dev.c:5556 __netif_receive_skb_list net/core/dev.c:5608 [inline] netif_receive_skb_list_internal+0x75e/0xd80 net/core/dev.c:5699 gro_normal_list net/core/dev.c:5853 [inline] gro_normal_list net/core/dev.c:5849 [inline] napi_complete_done+0x1f1/0x880 net/core/dev.c:6590 virtqueue_napi_complete drivers/net/virtio_net.c:339 [inline] virtnet_poll+0xca2/0x11b0 drivers/net/virtio_net.c:1557 __napi_poll+0xaf/0x440 net/core/dev.c:7023 napi_poll net/core/dev.c:7090 [inline] net_rx_action+0x801/0xb40 net/core/dev.c:7177 __do_softirq+0x29b/0x9c2 kernel/softirq.c:558 invoke_softirq kernel/softirq.c:432 [inline] __irq_exit_rcu+0x123/0x180 kernel/softirq.c:637 irq_exit_rcu+0x5/0x20 kernel/softirq.c:649 common_interrupt+0x52/0xc0 arch/x86/kernel/irq.c:240 asm_common_interrupt+0x1e/0x40 arch/x86/include/asm/idtentry.h:629 RIP: 0033:0x7f5e972bfd57 Code: 39 d1 73 14 0f 1f 80 00 00 00 00 48 8b 50 f8 48 83 e8 08 48 39 ca 77 f3 48 39 c3 73 3e 48 89 13 48 8b 50 f8 48 89 38 49 8b 0e <48> 8b 3e 48 83 c3 08 48 83 c6 08 eb bc 48 39 d1 72 9e 48 39 d0 73 RSP: 002b:00007fff8a413210 EFLAGS: 00000283 RAX: 00007f5e97108990 RBX: 00007f5e97108338 RCX: ffffffff81d3aa45 RDX: ffffffff81d3aa45 RSI: 00007f5e97108340 RDI: ffffffff81d3aa45 RBP: 00007f5e97107eb8 R08: 00007f5e97108d88 R09: 0000000093c2e8d9 R10: 0000000000000000 R11: 0000000000000000 R12: 00007f5e97107eb0 R13: 00007f5e97108338 R14: 00007f5e97107ea8 R15: 0000000000000019 </TASK> Allocated by task 13: kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38 kasan_set_track mm/kasan/common.c:46 [inline] set_alloc_info mm/kasan/common.c:434 [inline] __kasan_slab_alloc+0x90/0xc0 mm/kasan/common.c:467 kasan_slab_alloc include/linux/kasan.h:259 [inline] slab_post_alloc_hook mm/slab.h:519 [inline] slab_alloc_node mm/slub.c:3234 [inline] slab_alloc mm/slub.c:3242 [inline] kmem_cache_alloc+0x202/0x3a0 mm/slub.c:3247 dst_alloc+0x146/0x1f0 net/core/dst.c:92 rt_dst_alloc+0x73/0x430 net/ipv4/route.c:1613 ip_route_input_slow+0x1817/0x3a20 net/ipv4/route.c:234 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ath10k: Fix a use after free in ath10k_htc_send_bundle In ath10k_htc_send_bundle, the bundle_skb could be freed by dev_kfree_skb_any(bundle_skb). But the bundle_skb is used later by bundle_skb->len. As skb_len = bundle_skb->len, my patch replaces bundle_skb->len to skb_len after the bundle_skb was freed.

In the Linux kernel, the following vulnerability has been resolved: RDMA/rtrs-clt: destroy sysfs after removing session from active list A session can be removed dynamically by sysfs interface "remove_path" that eventually calls rtrs_clt_remove_path_from_sysfs function. The current rtrs_clt_remove_path_from_sysfs first removes the sysfs interfaces and frees sess->stats object. Second it removes the session from the active list. Therefore some functions could access non-connected session and access the freed sess->stats object even-if they check the session status before accessing the session. For instance rtrs_clt_request and get_next_path_min_inflight check the session status and try to send IO to the session. The session status could be changed when they are trying to send IO but they could not catch the change and update the statistics information in sess->stats object, and generate use-after-free problem. (see: "RDMA/rtrs-clt: Check state of the rtrs_clt_sess before reading its stats") This patch changes the rtrs_clt_remove_path_from_sysfs to remove the session from the active session list and then destroy the sysfs interfaces. Each function still should check the session status because closing or error recovery paths can change the status.

In the Linux kernel, the following vulnerability has been resolved: bpf: Track subprog poke descriptors correctly and fix use-after-free Subprograms are calling map_poke_track(), but on program release there is no hook to call map_poke_untrack(). However, on program release, the aux memory (and poke descriptor table) is freed even though we still have a reference to it in the element list of the map aux data. When we run map_poke_run(), we then end up accessing free'd memory, triggering KASAN in prog_array_map_poke_run(): [...] [ 402.824689] BUG: KASAN: use-after-free in prog_array_map_poke_run+0xc2/0x34e [ 402.824698] Read of size 4 at addr ffff8881905a7940 by task hubble-fgs/4337 [ 402.824705] CPU: 1 PID: 4337 Comm: hubble-fgs Tainted: G I 5.12.0+ #399 [ 402.824715] Call Trace: [ 402.824719] dump_stack+0x93/0xc2 [ 402.824727] print_address_description.constprop.0+0x1a/0x140 [ 402.824736] ? prog_array_map_poke_run+0xc2/0x34e [ 402.824740] ? prog_array_map_poke_run+0xc2/0x34e [ 402.824744] kasan_report.cold+0x7c/0xd8 [ 402.824752] ? prog_array_map_poke_run+0xc2/0x34e [ 402.824757] prog_array_map_poke_run+0xc2/0x34e [ 402.824765] bpf_fd_array_map_update_elem+0x124/0x1a0 [...] The elements concerned are walked as follows: for (i = 0; i < elem->aux->size_poke_tab; i++) { poke = &elem->aux->poke_tab[i]; [...] The access to size_poke_tab is a 4 byte read, verified by checking offsets in the KASAN dump: [ 402.825004] The buggy address belongs to the object at ffff8881905a7800 which belongs to the cache kmalloc-1k of size 1024 [ 402.825008] The buggy address is located 320 bytes inside of 1024-byte region [ffff8881905a7800, ffff8881905a7c00) The pahole output of bpf_prog_aux: struct bpf_prog_aux { [...] /* --- cacheline 5 boundary (320 bytes) --- */ u32 size_poke_tab; /* 320 4 */ [...] In general, subprograms do not necessarily manage their own data structures. For example, BTF func_info and linfo are just pointers to the main program structure. This allows reference counting and cleanup to be done on the latter which simplifies their management a bit. The aux->poke_tab struct, however, did not follow this logic. The initial proposed fix for this use-after-free bug further embedded poke data tracking into the subprogram with proper reference counting. However, Daniel and Alexei questioned why we were treating these objects special; I agree, its unnecessary. The fix here removes the per subprogram poke table allocation and map tracking and instead simply points the aux->poke_tab pointer at the main programs poke table. This way, map tracking is simplified to the main program and we do not need to manage them per subprogram. This also means, bpf_prog_free_deferred(), which unwinds the program reference counting and kfrees objects, needs to ensure that we don't try to double free the poke_tab when free'ing the subprog structures. This is easily solved by NULL'ing the poke_tab pointer. The second detail is to ensure that per subprogram JIT logic only does fixups on poke_tab[] entries it owns. To do this, we add a pointer in the poke structure to point at the subprogram value so JITs can easily check while walking the poke_tab structure if the current entry belongs to the current program. The aux pointer is stable and therefore suitable for such comparison. On the jit_subprogs() error path, we omit cleaning up the poke->aux field because these are only ever referenced from the JIT side, but on error we will never make it to the JIT, so its fine to leave them dangling. Removing these pointers would complicate the error path for no reason. However, we do need to untrack all poke descriptors from the main program as otherwise they could race with the freeing of JIT memory from the subprograms. Lastly, a748c6975dea3 ("bpf: propagate poke des ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net: dpaa2-eth: fix use-after-free in dpaa2_eth_remove Access to netdev after free_netdev() will cause use-after-free bug. Move debug log before free_netdev() call to avoid it.

In the Linux kernel, the following vulnerability has been resolved: watchdog: Fix possible use-after-free by calling del_timer_sync() This driver's remove path calls del_timer(). However, that function does not wait until the timer handler finishes. This means that the timer handler may still be running after the driver's remove function has finished, which would result in a use-after-free. Fix by calling del_timer_sync(), which makes sure the timer handler has finished, and unable to re-schedule itself.

In the Linux kernel, the following vulnerability has been resolved: mac80211: fix use-after-free in CCMP/GCMP RX When PN checking is done in mac80211, for fragmentation we need to copy the PN to the RX struct so we can later use it to do a comparison, since commit bf30ca922a0c ("mac80211: check defrag PN against current frame"). Unfortunately, in that commit I used the 'hdr' variable without it being necessarily valid, so use-after-free could occur if it was necessary to reallocate (parts of) the frame. Fix this by reloading the variable after the code that results in the reallocations, if any. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=214401.

In the Linux kernel, the following vulnerability has been resolved: ACPI: custom_method: fix potential use-after-free issue In cm_write(), buf is always freed when reaching the end of the function. If the requested count is less than table.length, the allocated buffer will be freed but subsequent calls to cm_write() will still try to access it. Remove the unconditional kfree(buf) at the end of the function and set the buf to NULL in the -EINVAL error path to match the rest of function.

In the Linux kernel, the following vulnerability has been resolved: RDMA/siw: Fix a use after free in siw_alloc_mr Our code analyzer reported a UAF. In siw_alloc_mr(), it calls siw_mr_add_mem(mr,..). In the implementation of siw_mr_add_mem(), mem is assigned to mr->mem and then mem is freed via kfree(mem) if xa_alloc_cyclic() failed. Here, mr->mem still point to a freed object. After, the execution continue up to the err_out branch of siw_alloc_mr, and the freed mr->mem is used in siw_mr_drop_mem(mr). My patch moves "mr->mem = mem" behind the if (xa_alloc_cyclic(..)<0) {} section, to avoid the uaf.

In the Linux kernel, the following vulnerability has been resolved: io_uring: fix ltout double free on completion race Always remove linked timeout on io_link_timeout_fn() from the master request link list, otherwise we may get use-after-free when first io_link_timeout_fn() puts linked timeout in the fail path, and then will be found and put on master's free.

In the Linux kernel, the following vulnerability has been resolved: can: sja1000: fix use after free in ems_pcmcia_add_card() If the last channel is not available then "dev" is freed. Fortunately, we can just use "pdev->irq" instead. Also we should check if at least one channel was set up.

In the Linux kernel, the following vulnerability has been resolved: can: dev: can_restart: fix use after free bug After calling netif_rx_ni(skb), dereferencing skb is unsafe. Especially, the can_frame cf which aliases skb memory is accessed after the netif_rx_ni() in: stats->rx_bytes += cf->len; Reordering the lines solves the issue.

In the Linux kernel, the following vulnerability has been resolved: net: ll_temac: Make sure to free skb when it is completely used With the skb pointer piggy-backed on the TX BD, we have a simple and efficient way to free the skb buffer when the frame has been transmitted. But in order to avoid freeing the skb while there are still fragments from the skb in use, we need to piggy-back on the TX BD of the skb, not the first. Without this, we are doing use-after-free on the DMA side, when the first BD of a multi TX BD packet is seen as completed in xmit_done, and the remaining BDs are still being processed.

A use-after-free vulnerability in the Linux kernel's netfilter: nf_tables component can be exploited to achieve local privilege escalation. Due to a race condition between nf_tables netlink control plane transaction and nft_set element garbage collection, it is possible to underflow the reference counter causing a use-after-free vulnerability. We recommend upgrading past commit 3e91b0ebd994635df2346353322ac51ce84ce6d8.

A use-after-free vulnerability in the Linux kernel's net/sched: cls_route component can be exploited to achieve local privilege escalation. When route4_change() is called on an existing filter, the whole tcf_result struct is always copied into the new instance of the filter. This causes a problem when updating a filter bound to a class, as tcf_unbind_filter() is always called on the old instance in the success path, decreasing filter_cnt of the still referenced class and allowing it to be deleted, leading to a use-after-free. We recommend upgrading past commit b80b829e9e2c1b3f7aae34855e04d8f6ecaf13c8.

A use-after-free vulnerability in the Linux kernel's net/sched: cls_u32 component can be exploited to achieve local privilege escalation. When u32_change() is called on an existing filter, the whole tcf_result struct is always copied into the new instance of the filter. This causes a problem when updating a filter bound to a class, as tcf_unbind_filter() is always called on the old instance in the success path, decreasing filter_cnt of the still referenced class and allowing it to be deleted, leading to a use-after-free. We recommend upgrading past commit 3044b16e7c6fe5d24b1cdbcf1bd0a9d92d1ebd81.

A use-after-free vulnerability in the Linux kernel's net/sched: cls_fw component can be exploited to achieve local privilege escalation. When fw_change() is called on an existing filter, the whole tcf_result struct is always copied into the new instance of the filter. This causes a problem when updating a filter bound to a class, as tcf_unbind_filter() is always called on the old instance in the success path, decreasing filter_cnt of the still referenced class and allowing it to be deleted, leading to a use-after-free. We recommend upgrading past commit 76e42ae831991c828cffa8c37736ebfb831ad5ec.

In the Linux kernel, the following vulnerability has been resolved: mm/slab_common: fix possible double free of kmem_cache When doing slub_debug test, kfence's 'test_memcache_typesafe_by_rcu' kunit test case cause a use-after-free error: BUG: KASAN: use-after-free in kobject_del+0x14/0x30 Read of size 8 at addr ffff888007679090 by task kunit_try_catch/261 CPU: 1 PID: 261 Comm: kunit_try_catch Tainted: G B N 6.0.0-rc5-next-20220916 #17 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x34/0x48 print_address_description.constprop.0+0x87/0x2a5 print_report+0x103/0x1ed kasan_report+0xb7/0x140 kobject_del+0x14/0x30 kmem_cache_destroy+0x130/0x170 test_exit+0x1a/0x30 kunit_try_run_case+0xad/0xc0 kunit_generic_run_threadfn_adapter+0x26/0x50 kthread+0x17b/0x1b0 </TASK> The cause is inside kmem_cache_destroy(): kmem_cache_destroy acquire lock/mutex shutdown_cache schedule_work(kmem_cache_release) (if RCU flag set) release lock/mutex kmem_cache_release (if RCU flag not set) In some certain timing, the scheduled work could be run before the next RCU flag checking, which can then get a wrong value and lead to double kmem_cache_release(). Fix it by caching the RCU flag inside protected area, just like 'refcnt'

A use-after-free vulnerability in the Linux kernel's netfilter: nf_tables component can be exploited to achieve local privilege escalation. On an error when building a nftables rule, deactivating immediate expressions in nft_immediate_deactivate() can lead unbinding the chain and objects be deactivated but later used. We recommend upgrading past commit 0a771f7b266b02d262900c75f1e175c7fe76fec2.

A use-after-free vulnerability in the Linux kernel's netfilter: nf_tables component can be exploited to achieve local privilege escalation. When nf_tables_delrule() is flushing table rules, it is not checked whether the chain is bound and the chain's owner rule can also release the objects in certain circumstances. We recommend upgrading past commit 6eaf41e87a223ae6f8e7a28d6e78384ad7e407f8.

A use-after-free vulnerability in the Linux kernel's net/sched: cls_fw component can be exploited to achieve local privilege escalation. If tcf_change_indev() fails, fw_set_parms() will immediately return an error after incrementing or decrementing the reference counter in tcf_bind_filter(). If an attacker can control the reference counter and set it to zero, they can cause the reference to be freed, leading to a use-after-free vulnerability. We recommend upgrading past commit 0323bce598eea038714f941ce2b22541c46d488f.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix use-after-free bug in cifs_debug_data_proc_show() Skip SMB sessions that are being teared down (e.g. @ses->ses_status == SES_EXITING) in cifs_debug_data_proc_show() to avoid use-after-free in @ses. This fixes the following GPF when reading from /proc/fs/cifs/DebugData while mounting and umounting [ 816.251274] general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6d81: 0000 [#1] PREEMPT SMP NOPTI ... [ 816.260138] Call Trace: [ 816.260329] <TASK> [ 816.260499] ? die_addr+0x36/0x90 [ 816.260762] ? exc_general_protection+0x1b3/0x410 [ 816.261126] ? asm_exc_general_protection+0x26/0x30 [ 816.261502] ? cifs_debug_tcon+0xbd/0x240 [cifs] [ 816.261878] ? cifs_debug_tcon+0xab/0x240 [cifs] [ 816.262249] cifs_debug_data_proc_show+0x516/0xdb0 [cifs] [ 816.262689] ? seq_read_iter+0x379/0x470 [ 816.262995] seq_read_iter+0x118/0x470 [ 816.263291] proc_reg_read_iter+0x53/0x90 [ 816.263596] ? srso_alias_return_thunk+0x5/0x7f [ 816.263945] vfs_read+0x201/0x350 [ 816.264211] ksys_read+0x75/0x100 [ 816.264472] do_syscall_64+0x3f/0x90 [ 816.264750] entry_SYSCALL_64_after_hwframe+0x6e/0xd8 [ 816.265135] RIP: 0033:0x7fd5e669d381

In the Linux kernel, the following vulnerability has been resolved: IB/mlx5: Fix init stage error handling to avoid double free of same QP and UAF In the unlikely event that workqueue allocation fails and returns NULL in mlx5_mkey_cache_init(), delete the call to mlx5r_umr_resource_cleanup() (which frees the QP) in mlx5_ib_stage_post_ib_reg_umr_init(). This will avoid attempted double free of the same QP when __mlx5_ib_add() does its cleanup. Resolves a splat: Syzkaller reported a UAF in ib_destroy_qp_user workqueue: Failed to create a rescuer kthread for wq "mkey_cache": -EINTR infiniband mlx5_0: mlx5_mkey_cache_init:981:(pid 1642): failed to create work queue infiniband mlx5_0: mlx5_ib_stage_post_ib_reg_umr_init:4075:(pid 1642): mr cache init failed -12 ================================================================== BUG: KASAN: slab-use-after-free in ib_destroy_qp_user (drivers/infiniband/core/verbs.c:2073) Read of size 8 at addr ffff88810da310a8 by task repro_upstream/1642 Call Trace: <TASK> kasan_report (mm/kasan/report.c:590) ib_destroy_qp_user (drivers/infiniband/core/verbs.c:2073) mlx5r_umr_resource_cleanup (drivers/infiniband/hw/mlx5/umr.c:198) __mlx5_ib_add (drivers/infiniband/hw/mlx5/main.c:4178) mlx5r_probe (drivers/infiniband/hw/mlx5/main.c:4402) ... </TASK> Allocated by task 1642: __kmalloc (./include/linux/kasan.h:198 mm/slab_common.c:1026 mm/slab_common.c:1039) create_qp (./include/linux/slab.h:603 ./include/linux/slab.h:720 ./include/rdma/ib_verbs.h:2795 drivers/infiniband/core/verbs.c:1209) ib_create_qp_kernel (drivers/infiniband/core/verbs.c:1347) mlx5r_umr_resource_init (drivers/infiniband/hw/mlx5/umr.c:164) mlx5_ib_stage_post_ib_reg_umr_init (drivers/infiniband/hw/mlx5/main.c:4070) __mlx5_ib_add (drivers/infiniband/hw/mlx5/main.c:4168) mlx5r_probe (drivers/infiniband/hw/mlx5/main.c:4402) ... Freed by task 1642: __kmem_cache_free (mm/slub.c:1826 mm/slub.c:3809 mm/slub.c:3822) ib_destroy_qp_user (drivers/infiniband/core/verbs.c:2112) mlx5r_umr_resource_cleanup (drivers/infiniband/hw/mlx5/umr.c:198) mlx5_ib_stage_post_ib_reg_umr_init (drivers/infiniband/hw/mlx5/main.c:4076 drivers/infiniband/hw/mlx5/main.c:4065) __mlx5_ib_add (drivers/infiniband/hw/mlx5/main.c:4168) mlx5r_probe (drivers/infiniband/hw/mlx5/main.c:4402) ...

In the Linux kernel, the following vulnerability has been resolved: sched/psi: Fix use-after-free in ep_remove_wait_queue() If a non-root cgroup gets removed when there is a thread that registered trigger and is polling on a pressure file within the cgroup, the polling waitqueue gets freed in the following path: do_rmdir cgroup_rmdir kernfs_drain_open_files cgroup_file_release cgroup_pressure_release psi_trigger_destroy However, the polling thread still has a reference to the pressure file and will access the freed waitqueue when the file is closed or upon exit: fput ep_eventpoll_release ep_free ep_remove_wait_queue remove_wait_queue This results in use-after-free as pasted below. The fundamental problem here is that cgroup_file_release() (and consequently waitqueue's lifetime) is not tied to the file's real lifetime. Using wake_up_pollfree() here might be less than ideal, but it is in line with the comment at commit 42288cb44c4b ("wait: add wake_up_pollfree()") since the waitqueue's lifetime is not tied to file's one and can be considered as another special case. While this would be fixable by somehow making cgroup_file_release() be tied to the fput(), it would require sizable refactoring at cgroups or higher layer which might be more justifiable if we identify more cases like this. BUG: KASAN: use-after-free in _raw_spin_lock_irqsave+0x60/0xc0 Write of size 4 at addr ffff88810e625328 by task a.out/4404 CPU: 19 PID: 4404 Comm: a.out Not tainted 6.2.0-rc6 #38 Hardware name: Amazon EC2 c5a.8xlarge/, BIOS 1.0 10/16/2017 Call Trace: <TASK> dump_stack_lvl+0x73/0xa0 print_report+0x16c/0x4e0 kasan_report+0xc3/0xf0 kasan_check_range+0x2d2/0x310 _raw_spin_lock_irqsave+0x60/0xc0 remove_wait_queue+0x1a/0xa0 ep_free+0x12c/0x170 ep_eventpoll_release+0x26/0x30 __fput+0x202/0x400 task_work_run+0x11d/0x170 do_exit+0x495/0x1130 do_group_exit+0x100/0x100 get_signal+0xd67/0xde0 arch_do_signal_or_restart+0x2a/0x2b0 exit_to_user_mode_prepare+0x94/0x100 syscall_exit_to_user_mode+0x20/0x40 do_syscall_64+0x52/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd </TASK> Allocated by task 4404: kasan_set_track+0x3d/0x60 __kasan_kmalloc+0x85/0x90 psi_trigger_create+0x113/0x3e0 pressure_write+0x146/0x2e0 cgroup_file_write+0x11c/0x250 kernfs_fop_write_iter+0x186/0x220 vfs_write+0x3d8/0x5c0 ksys_write+0x90/0x110 do_syscall_64+0x43/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd Freed by task 4407: kasan_set_track+0x3d/0x60 kasan_save_free_info+0x27/0x40 ____kasan_slab_free+0x11d/0x170 slab_free_freelist_hook+0x87/0x150 __kmem_cache_free+0xcb/0x180 psi_trigger_destroy+0x2e8/0x310 cgroup_file_release+0x4f/0xb0 kernfs_drain_open_files+0x165/0x1f0 kernfs_drain+0x162/0x1a0 __kernfs_remove+0x1fb/0x310 kernfs_remove_by_name_ns+0x95/0xe0 cgroup_addrm_files+0x67f/0x700 cgroup_destroy_locked+0x283/0x3c0 cgroup_rmdir+0x29/0x100 kernfs_iop_rmdir+0xd1/0x140 vfs_rmdir+0xfe/0x240 do_rmdir+0x13d/0x280 __x64_sys_rmdir+0x2c/0x30 do_syscall_64+0x43/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd

A use-after-free vulnerability in the Linux kernel's net/sched: cls_u32 component can be exploited to achieve local privilege escalation. If tcf_change_indev() fails, u32_set_parms() will immediately return an error after incrementing or decrementing the reference counter in tcf_bind_filter(). If an attacker can control the reference counter and set it to zero, they can cause the reference to be freed, leading to a use-after-free vulnerability. We recommend upgrading past commit 04c55383fa5689357bcdd2c8036725a55ed632bc.

A use-after-free vulnerability in the Linux kernel's netfilter: nf_tables component can be exploited to achieve local privilege escalation. Flaw in the error handling of bound chains causes a use-after-free in the abort path of NFT_MSG_NEWRULE. The vulnerability requires CAP_NET_ADMIN to be triggered. We recommend upgrading past commit 4bedf9eee016286c835e3d8fa981ddece5338795.

A use-after-free vulnerability in the Linux Kernel io_uring subsystem can be exploited to achieve local privilege escalation. Racing a io_uring cancel poll request with a linked timeout can cause a UAF in a hrtimer. We recommend upgrading past commit ef7dfac51d8ed961b742218f526bd589f3900a59 (4716c73b188566865bdd79c3a6709696a224ac04 for 5.10 stable and 0e388fce7aec40992eadee654193cad345d62663 for 5.15 stable).

A use-after-free vulnerability was found in the Linux kernel's netfilter subsystem in net/netfilter/nf_tables_api.c. Mishandled error handling with NFT_MSG_NEWRULE makes it possible to use a dangling pointer in the same transaction causing a use-after-free vulnerability. This flaw allows a local attacker with user access to cause a privilege escalation issue. We recommend upgrading past commit 1240eb93f0616b21c675416516ff3d74798fdc97.

In the Linux kernel, the following vulnerability has been resolved: block, bfq: fix waker_bfqq UAF after bfq_split_bfqq() Our syzkaller report a following UAF for v6.6: BUG: KASAN: slab-use-after-free in bfq_init_rq+0x175d/0x17a0 block/bfq-iosched.c:6958 Read of size 8 at addr ffff8881b57147d8 by task fsstress/232726 CPU: 2 PID: 232726 Comm: fsstress Not tainted 6.6.0-g3629d1885222 #39 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x91/0xf0 lib/dump_stack.c:106 print_address_description.constprop.0+0x66/0x300 mm/kasan/report.c:364 print_report+0x3e/0x70 mm/kasan/report.c:475 kasan_report+0xb8/0xf0 mm/kasan/report.c:588 hlist_add_head include/linux/list.h:1023 [inline] bfq_init_rq+0x175d/0x17a0 block/bfq-iosched.c:6958 bfq_insert_request.isra.0+0xe8/0xa20 block/bfq-iosched.c:6271 bfq_insert_requests+0x27f/0x390 block/bfq-iosched.c:6323 blk_mq_insert_request+0x290/0x8f0 block/blk-mq.c:2660 blk_mq_submit_bio+0x1021/0x15e0 block/blk-mq.c:3143 __submit_bio+0xa0/0x6b0 block/blk-core.c:639 __submit_bio_noacct_mq block/blk-core.c:718 [inline] submit_bio_noacct_nocheck+0x5b7/0x810 block/blk-core.c:747 submit_bio_noacct+0xca0/0x1990 block/blk-core.c:847 __ext4_read_bh fs/ext4/super.c:205 [inline] ext4_read_bh+0x15e/0x2e0 fs/ext4/super.c:230 __read_extent_tree_block+0x304/0x6f0 fs/ext4/extents.c:567 ext4_find_extent+0x479/0xd20 fs/ext4/extents.c:947 ext4_ext_map_blocks+0x1a3/0x2680 fs/ext4/extents.c:4182 ext4_map_blocks+0x929/0x15a0 fs/ext4/inode.c:660 ext4_iomap_begin_report+0x298/0x480 fs/ext4/inode.c:3569 iomap_iter+0x3dd/0x1010 fs/iomap/iter.c:91 iomap_fiemap+0x1f4/0x360 fs/iomap/fiemap.c:80 ext4_fiemap+0x181/0x210 fs/ext4/extents.c:5051 ioctl_fiemap.isra.0+0x1b4/0x290 fs/ioctl.c:220 do_vfs_ioctl+0x31c/0x11a0 fs/ioctl.c:811 __do_sys_ioctl fs/ioctl.c:869 [inline] __se_sys_ioctl+0xae/0x190 fs/ioctl.c:857 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x70/0x120 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x78/0xe2 Allocated by task 232719: kasan_save_stack+0x22/0x50 mm/kasan/common.c:45 kasan_set_track+0x25/0x30 mm/kasan/common.c:52 __kasan_slab_alloc+0x87/0x90 mm/kasan/common.c:328 kasan_slab_alloc include/linux/kasan.h:188 [inline] slab_post_alloc_hook mm/slab.h:768 [inline] slab_alloc_node mm/slub.c:3492 [inline] kmem_cache_alloc_node+0x1b8/0x6f0 mm/slub.c:3537 bfq_get_queue+0x215/0x1f00 block/bfq-iosched.c:5869 bfq_get_bfqq_handle_split+0x167/0x5f0 block/bfq-iosched.c:6776 bfq_init_rq+0x13a4/0x17a0 block/bfq-iosched.c:6938 bfq_insert_request.isra.0+0xe8/0xa20 block/bfq-iosched.c:6271 bfq_insert_requests+0x27f/0x390 block/bfq-iosched.c:6323 blk_mq_insert_request+0x290/0x8f0 block/blk-mq.c:2660 blk_mq_submit_bio+0x1021/0x15e0 block/blk-mq.c:3143 __submit_bio+0xa0/0x6b0 block/blk-core.c:639 __submit_bio_noacct_mq block/blk-core.c:718 [inline] submit_bio_noacct_nocheck+0x5b7/0x810 block/blk-core.c:747 submit_bio_noacct+0xca0/0x1990 block/blk-core.c:847 __ext4_read_bh fs/ext4/super.c:205 [inline] ext4_read_bh_nowait+0x15a/0x240 fs/ext4/super.c:217 ext4_read_bh_lock+0xac/0xd0 fs/ext4/super.c:242 ext4_bread_batch+0x268/0x500 fs/ext4/inode.c:958 __ext4_find_entry+0x448/0x10f0 fs/ext4/namei.c:1671 ext4_lookup_entry fs/ext4/namei.c:1774 [inline] ext4_lookup.part.0+0x359/0x6f0 fs/ext4/namei.c:1842 ext4_lookup+0x72/0x90 fs/ext4/namei.c:1839 __lookup_slow+0x257/0x480 fs/namei.c:1696 lookup_slow fs/namei.c:1713 [inline] walk_component+0x454/0x5c0 fs/namei.c:2004 link_path_walk.part.0+0x773/0xda0 fs/namei.c:2331 link_path_walk fs/namei.c:3826 [inline] path_openat+0x1b9/0x520 fs/namei.c:3826 do_filp_open+0x1b7/0x400 fs/namei.c:3857 do_sys_openat2+0x5dc/0x6e0 fs/open.c:1428 do_sys_open fs/open.c:1443 [inline] __do_sys_openat fs/open.c:1459 [inline] __se_sys_openat fs/open.c:1454 [inline] __x64_sys_openat+0x148/0x200 fs/open.c:1454 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_6 ---truncated---

Linux Kernel nftables Use-After-Free Local Privilege Escalation Vulnerability; `nft_chain_lookup_byid()` failed to check whether a chain was active and CAP_NET_ADMIN is in any user or network namespace

In the Linux kernel, the following vulnerability has been resolved: padata: fix UAF in padata_reorder A bug was found when run ltp test: BUG: KASAN: slab-use-after-free in padata_find_next+0x29/0x1a0 Read of size 4 at addr ffff88bbfe003524 by task kworker/u113:2/3039206 CPU: 0 PID: 3039206 Comm: kworker/u113:2 Kdump: loaded Not tainted 6.6.0+ Workqueue: pdecrypt_parallel padata_parallel_worker Call Trace: <TASK> dump_stack_lvl+0x32/0x50 print_address_description.constprop.0+0x6b/0x3d0 print_report+0xdd/0x2c0 kasan_report+0xa5/0xd0 padata_find_next+0x29/0x1a0 padata_reorder+0x131/0x220 padata_parallel_worker+0x3d/0xc0 process_one_work+0x2ec/0x5a0 If 'mdelay(10)' is added before calling 'padata_find_next' in the 'padata_reorder' function, this issue could be reproduced easily with ltp test (pcrypt_aead01). This can be explained as bellow: pcrypt_aead_encrypt ... padata_do_parallel refcount_inc(&pd->refcnt); // add refcnt ... padata_do_serial padata_reorder // pd while (1) { padata_find_next(pd, true); // using pd queue_work_on ... padata_serial_worker crypto_del_alg padata_put_pd_cnt // sub refcnt padata_free_shell padata_put_pd(ps->pd); // pd is freed // loop again, but pd is freed // call padata_find_next, UAF } In the padata_reorder function, when it loops in 'while', if the alg is deleted, the refcnt may be decreased to 0 before entering 'padata_find_next', which leads to UAF. As mentioned in [1], do_serial is supposed to be called with BHs disabled and always happen under RCU protection, to address this issue, add synchronize_rcu() in 'padata_free_shell' wait for all _do_serial calls to finish. [1] https://lore.kernel.org/all/20221028160401.cccypv4euxikusiq@parnassus.localdomain/ [2] https://lore.kernel.org/linux-kernel/jfjz5d7zwbytztackem7ibzalm5lnxldi2eofeiczqmqs2m7o6@fq426cwnjtkm/

In the Linux kernel, the following vulnerability has been resolved: cdx: Fix possible UAF error in driver_override_show() Fixed a possible UAF problem in driver_override_show() in drivers/cdx/cdx.c This function driver_override_show() is part of DEVICE_ATTR_RW, which includes both driver_override_show() and driver_override_store(). These functions can be executed concurrently in sysfs. The driver_override_store() function uses driver_set_override() to update the driver_override value, and driver_set_override() internally locks the device (device_lock(dev)). If driver_override_show() reads cdx_dev->driver_override without locking, it could potentially access a freed pointer if driver_override_store() frees the string concurrently. This could lead to printing a kernel address, which is a security risk since DEVICE_ATTR can be read by all users. Additionally, a similar pattern is used in drivers/amba/bus.c, as well as many other bus drivers, where device_lock() is taken in the show function, and it has been working without issues. This potential bug was detected by our experimental static analysis tool, which analyzes locking APIs and paired functions to identify data races and atomicity violations.

In the Linux kernel, the following vulnerability has been resolved: HID: intel-ish-hid: Fix use-after-free issue in hid_ishtp_cl_remove() During the `rmmod` operation for the `intel_ishtp_hid` driver, a use-after-free issue can occur in the hid_ishtp_cl_remove() function. The function hid_ishtp_cl_deinit() is called before ishtp_hid_remove(), which can lead to accessing freed memory or resources during the removal process. Call Trace: ? ishtp_cl_send+0x168/0x220 [intel_ishtp] ? hid_output_report+0xe3/0x150 [hid] hid_ishtp_set_feature+0xb5/0x120 [intel_ishtp_hid] ishtp_hid_request+0x7b/0xb0 [intel_ishtp_hid] hid_hw_request+0x1f/0x40 [hid] sensor_hub_set_feature+0x11f/0x190 [hid_sensor_hub] _hid_sensor_power_state+0x147/0x1e0 [hid_sensor_trigger] hid_sensor_runtime_resume+0x22/0x30 [hid_sensor_trigger] sensor_hub_remove+0xa8/0xe0 [hid_sensor_hub] hid_device_remove+0x49/0xb0 [hid] hid_destroy_device+0x6f/0x90 [hid] ishtp_hid_remove+0x42/0x70 [intel_ishtp_hid] hid_ishtp_cl_remove+0x6b/0xb0 [intel_ishtp_hid] ishtp_cl_device_remove+0x4a/0x60 [intel_ishtp] ... Additionally, ishtp_hid_remove() is a HID level power off, which should occur before the ISHTP level disconnect. This patch resolves the issue by reordering the calls in hid_ishtp_cl_remove(). The function ishtp_hid_remove() is now called before hid_ishtp_cl_deinit().

In the Linux kernel, the following vulnerability has been resolved: mm/migrate_device: don't add folio to be freed to LRU in migrate_device_finalize() If migration succeeded, we called folio_migrate_flags()->mem_cgroup_migrate() to migrate the memcg from the old to the new folio. This will set memcg_data of the old folio to 0. Similarly, if migration failed, memcg_data of the dst folio is left unset. If we call folio_putback_lru() on such folios (memcg_data == 0), we will add the folio to be freed to the LRU, making memcg code unhappy. Running the hmm selftests: # ./hmm-tests ... # RUN hmm.hmm_device_private.migrate ... [ 102.078007][T14893] page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x7ff27d200 pfn:0x13cc00 [ 102.079974][T14893] anon flags: 0x17ff00000020018(uptodate|dirty|swapbacked|node=0|zone=2|lastcpupid=0x7ff) [ 102.082037][T14893] raw: 017ff00000020018 dead000000000100 dead000000000122 ffff8881353896c9 [ 102.083687][T14893] raw: 00000007ff27d200 0000000000000000 00000001ffffffff 0000000000000000 [ 102.085331][T14893] page dumped because: VM_WARN_ON_ONCE_FOLIO(!memcg && !mem_cgroup_disabled()) [ 102.087230][T14893] ------------[ cut here ]------------ [ 102.088279][T14893] WARNING: CPU: 0 PID: 14893 at ./include/linux/memcontrol.h:726 folio_lruvec_lock_irqsave+0x10e/0x170 [ 102.090478][T14893] Modules linked in: [ 102.091244][T14893] CPU: 0 UID: 0 PID: 14893 Comm: hmm-tests Not tainted 6.13.0-09623-g6c216bc522fd #151 [ 102.093089][T14893] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014 [ 102.094848][T14893] RIP: 0010:folio_lruvec_lock_irqsave+0x10e/0x170 [ 102.096104][T14893] Code: ... [ 102.099908][T14893] RSP: 0018:ffffc900236c37b0 EFLAGS: 00010293 [ 102.101152][T14893] RAX: 0000000000000000 RBX: ffffea0004f30000 RCX: ffffffff8183f426 [ 102.102684][T14893] RDX: ffff8881063cb880 RSI: ffffffff81b8117f RDI: ffff8881063cb880 [ 102.104227][T14893] RBP: 0000000000000000 R08: 0000000000000005 R09: 0000000000000000 [ 102.105757][T14893] R10: 0000000000000001 R11: 0000000000000002 R12: ffffc900236c37d8 [ 102.107296][T14893] R13: ffff888277a2bcb0 R14: 000000000000001f R15: 0000000000000000 [ 102.108830][T14893] FS: 00007ff27dbdd740(0000) GS:ffff888277a00000(0000) knlGS:0000000000000000 [ 102.110643][T14893] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 102.111924][T14893] CR2: 00007ff27d400000 CR3: 000000010866e000 CR4: 0000000000750ef0 [ 102.113478][T14893] PKRU: 55555554 [ 102.114172][T14893] Call Trace: [ 102.114805][T14893] <TASK> [ 102.115397][T14893] ? folio_lruvec_lock_irqsave+0x10e/0x170 [ 102.116547][T14893] ? __warn.cold+0x110/0x210 [ 102.117461][T14893] ? folio_lruvec_lock_irqsave+0x10e/0x170 [ 102.118667][T14893] ? report_bug+0x1b9/0x320 [ 102.119571][T14893] ? handle_bug+0x54/0x90 [ 102.120494][T14893] ? exc_invalid_op+0x17/0x50 [ 102.121433][T14893] ? asm_exc_invalid_op+0x1a/0x20 [ 102.122435][T14893] ? __wake_up_klogd.part.0+0x76/0xd0 [ 102.123506][T14893] ? dump_page+0x4f/0x60 [ 102.124352][T14893] ? folio_lruvec_lock_irqsave+0x10e/0x170 [ 102.125500][T14893] folio_batch_move_lru+0xd4/0x200 [ 102.126577][T14893] ? __pfx_lru_add+0x10/0x10 [ 102.127505][T14893] __folio_batch_add_and_move+0x391/0x720 [ 102.128633][T14893] ? __pfx_lru_add+0x10/0x10 [ 102.129550][T14893] folio_putback_lru+0x16/0x80 [ 102.130564][T14893] migrate_device_finalize+0x9b/0x530 [ 102.131640][T14893] dmirror_migrate_to_device.constprop.0+0x7c5/0xad0 [ 102.133047][T14893] dmirror_fops_unlocked_ioctl+0x89b/0xc80 Likely, nothing else goes wrong: putting the last folio reference will remove the folio from the LRU again. So besides memcg complaining, adding the folio to be freed to the LRU is just an unnecessary step. The new flow resembles what we have in migrate_folio_move(): add the dst to the lru, rem ---truncated---

In the Linux kernel, the following vulnerability has been resolved: nilfs2: do not force clear folio if buffer is referenced Patch series "nilfs2: protect busy buffer heads from being force-cleared". This series fixes the buffer head state inconsistency issues reported by syzbot that occurs when the filesystem is corrupted and falls back to read-only, and the associated buffer head use-after-free issue. This patch (of 2): Syzbot has reported that after nilfs2 detects filesystem corruption and falls back to read-only, inconsistencies in the buffer state may occur. One of the inconsistencies is that when nilfs2 calls mark_buffer_dirty() to set a data or metadata buffer as dirty, but it detects that the buffer is not in the uptodate state: WARNING: CPU: 0 PID: 6049 at fs/buffer.c:1177 mark_buffer_dirty+0x2e5/0x520 fs/buffer.c:1177 ... Call Trace: <TASK> nilfs_palloc_commit_alloc_entry+0x4b/0x160 fs/nilfs2/alloc.c:598 nilfs_ifile_create_inode+0x1dd/0x3a0 fs/nilfs2/ifile.c:73 nilfs_new_inode+0x254/0x830 fs/nilfs2/inode.c:344 nilfs_mkdir+0x10d/0x340 fs/nilfs2/namei.c:218 vfs_mkdir+0x2f9/0x4f0 fs/namei.c:4257 do_mkdirat+0x264/0x3a0 fs/namei.c:4280 __do_sys_mkdirat fs/namei.c:4295 [inline] __se_sys_mkdirat fs/namei.c:4293 [inline] __x64_sys_mkdirat+0x87/0xa0 fs/namei.c:4293 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f The other is when nilfs_btree_propagate(), which propagates the dirty state to the ancestor nodes of a b-tree that point to a dirty buffer, detects that the origin buffer is not dirty, even though it should be: WARNING: CPU: 0 PID: 5245 at fs/nilfs2/btree.c:2089 nilfs_btree_propagate+0xc79/0xdf0 fs/nilfs2/btree.c:2089 ... Call Trace: <TASK> nilfs_bmap_propagate+0x75/0x120 fs/nilfs2/bmap.c:345 nilfs_collect_file_data+0x4d/0xd0 fs/nilfs2/segment.c:587 nilfs_segctor_apply_buffers+0x184/0x340 fs/nilfs2/segment.c:1006 nilfs_segctor_scan_file+0x28c/0xa50 fs/nilfs2/segment.c:1045 nilfs_segctor_collect_blocks fs/nilfs2/segment.c:1216 [inline] nilfs_segctor_collect fs/nilfs2/segment.c:1540 [inline] nilfs_segctor_do_construct+0x1c28/0x6b90 fs/nilfs2/segment.c:2115 nilfs_segctor_construct+0x181/0x6b0 fs/nilfs2/segment.c:2479 nilfs_segctor_thread_construct fs/nilfs2/segment.c:2587 [inline] nilfs_segctor_thread+0x69e/0xe80 fs/nilfs2/segment.c:2701 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 </TASK> Both of these issues are caused by the callbacks that handle the page/folio write requests, forcibly clear various states, including the working state of the buffers they hold, at unexpected times when they detect read-only fallback. Fix these issues by checking if the buffer is referenced before clearing the page/folio state, and skipping the clear if it is.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix use-after-free in ksmbd_sessions_deregister() In multichannel mode, UAF issue can occur in session_deregister when the second channel sets up a session through the connection of the first channel. session that is freed through the global session table can be accessed again through ->sessions of connection.

In the Linux kernel, the following vulnerability has been resolved: mm/khugepaged: fix ->anon_vma race If an ->anon_vma is attached to the VMA, collapse_and_free_pmd() requires it to be locked. Page table traversal is allowed under any one of the mmap lock, the anon_vma lock (if the VMA is associated with an anon_vma), and the mapping lock (if the VMA is associated with a mapping); and so to be able to remove page tables, we must hold all three of them. retract_page_tables() bails out if an ->anon_vma is attached, but does this check before holding the mmap lock (as the comment above the check explains). If we racily merged an existing ->anon_vma (shared with a child process) from a neighboring VMA, subsequent rmap traversals on pages belonging to the child will be able to see the page tables that we are concurrently removing while assuming that nothing else can access them. Repeat the ->anon_vma check once we hold the mmap lock to ensure that there really is no concurrent page table access. Hitting this bug causes a lockdep warning in collapse_and_free_pmd(), in the line "lockdep_assert_held_write(&vma->anon_vma->root->rwsem)". It can also lead to use-after-free access.

In the Linux kernel, the following vulnerability has been resolved: i2c: Fix a potential use after free Free the adap structure only after we are done using it. This patch just moves the put_device() down a bit to avoid the use after free. [wsa: added comment to the code, added Fixes tag]

In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Remove dangling pointers When an async control is written, we copy a pointer to the file handle that started the operation. That pointer will be used when the device is done. Which could be anytime in the future. If the user closes that file descriptor, its structure will be freed, and there will be one dangling pointer per pending async control, that the driver will try to use. Clean all the dangling pointers during release(). To avoid adding a performance penalty in the most common case (no async operation), a counter has been introduced with some logic to make sure that it is properly handled.