In the Linux kernel, the following vulnerability has been resolved: x86/kvm: Disable kvmclock on all CPUs on shutdown Currenly, we disable kvmclock from machine_shutdown() hook and this only happens for boot CPU. We need to disable it for all CPUs to guard against memory corruption e.g. on restore from hibernate. Note, writing '0' to kvmclock MSR doesn't clear memory location, it just prevents hypervisor from updating the location so for the short while after write and while CPU is still alive, the clock remains usable and correct so we don't need to switch to some other clocksource.

In the Linux kernel, the following vulnerability has been resolved: kvm: LAPIC: Restore guard to prevent illegal APIC register access Per the SDM, "any access that touches bytes 4 through 15 of an APIC register may cause undefined behavior and must not be executed." Worse, such an access in kvm_lapic_reg_read can result in a leak of kernel stack contents. Prior to commit 01402cf81051 ("kvm: LAPIC: write down valid APIC registers"), such an access was explicitly disallowed. Restore the guard that was removed in that commit.

In the Linux kernel, the following vulnerability has been resolved: mptcp: fix sk_forward_memory corruption on retransmission MPTCP sk_forward_memory handling is a bit special, as such field is protected by the msk socket spin_lock, instead of the plain socket lock. Currently we have a code path updating such field without handling the relevant lock: __mptcp_retrans() -> __mptcp_clean_una_wakeup() Several helpers in __mptcp_clean_una_wakeup() will update sk_forward_alloc, possibly causing such field corruption, as reported by Matthieu. Address the issue providing and using a new variant of blamed function which explicitly acquires the msk spin lock.

In the Linux kernel, the following vulnerability has been resolved: kvm: avoid speculation-based attacks from out-of-range memslot accesses KVM's mechanism for accessing guest memory translates a guest physical address (gpa) to a host virtual address using the right-shifted gpa (also known as gfn) and a struct kvm_memory_slot. The translation is performed in __gfn_to_hva_memslot using the following formula: hva = slot->userspace_addr + (gfn - slot->base_gfn) * PAGE_SIZE It is expected that gfn falls within the boundaries of the guest's physical memory. However, a guest can access invalid physical addresses in such a way that the gfn is invalid. __gfn_to_hva_memslot is called from kvm_vcpu_gfn_to_hva_prot, which first retrieves a memslot through __gfn_to_memslot. While __gfn_to_memslot does check that the gfn falls within the boundaries of the guest's physical memory or not, a CPU can speculate the result of the check and continue execution speculatively using an illegal gfn. The speculation can result in calculating an out-of-bounds hva. If the resulting host virtual address is used to load another guest physical address, this is effectively a Spectre gadget consisting of two consecutive reads, the second of which is data dependent on the first. Right now it's not clear if there are any cases in which this is exploitable. One interesting case was reported by the original author of this patch, and involves visiting guest page tables on x86. Right now these are not vulnerable because the hva read goes through get_user(), which contains an LFENCE speculation barrier. However, there are patches in progress for x86 uaccess.h to mask kernel addresses instead of using LFENCE; once these land, a guest could use speculation to read from the VMM's ring 3 address space. Other architectures such as ARM already use the address masking method, and would be susceptible to this same kind of data-dependent access gadgets. Therefore, this patch proactively protects from these attacks by masking out-of-bounds gfns in __gfn_to_hva_memslot, which blocks speculation of invalid hvas. Sean Christopherson noted that this patch does not cover kvm_read_guest_offset_cached. This however is limited to a few bytes past the end of the cache, and therefore it is unlikely to be useful in the context of building a chain of data dependent accesses.

In the Linux kernel, the following vulnerability has been resolved: ubifs: Fix read out-of-bounds in ubifs_wbuf_write_nolock() Function ubifs_wbuf_write_nolock() may access buf out of bounds in following process: ubifs_wbuf_write_nolock(): aligned_len = ALIGN(len, 8); // Assume len = 4089, aligned_len = 4096 if (aligned_len <= wbuf->avail) ... // Not satisfy if (wbuf->used) { ubifs_leb_write() // Fill some data in avail wbuf len -= wbuf->avail; // len is still not 8-bytes aligned aligned_len -= wbuf->avail; } n = aligned_len >> c->max_write_shift; if (n) { n <<= c->max_write_shift; err = ubifs_leb_write(c, wbuf->lnum, buf + written, wbuf->offs, n); // n > len, read out of bounds less than 8(n-len) bytes } , which can be catched by KASAN: ========================================================= BUG: KASAN: slab-out-of-bounds in ecc_sw_hamming_calculate+0x1dc/0x7d0 Read of size 4 at addr ffff888105594ff8 by task kworker/u8:4/128 Workqueue: writeback wb_workfn (flush-ubifs_0_0) Call Trace: kasan_report.cold+0x81/0x165 nand_write_page_swecc+0xa9/0x160 ubifs_leb_write+0xf2/0x1b0 [ubifs] ubifs_wbuf_write_nolock+0x421/0x12c0 [ubifs] write_head+0xdc/0x1c0 [ubifs] ubifs_jnl_write_inode+0x627/0x960 [ubifs] wb_workfn+0x8af/0xb80 Function ubifs_wbuf_write_nolock() accepts that parameter 'len' is not 8 bytes aligned, the 'len' represents the true length of buf (which is allocated in 'ubifs_jnl_xxx', eg. ubifs_jnl_write_inode), so ubifs_wbuf_write_nolock() must handle the length read from 'buf' carefully to write leb safely. Fetch a reproducer in [Link].

In the Linux kernel, the following vulnerability has been resolved: tty: Fix out-of-bound vmalloc access in imageblit This issue happens when a userspace program does an ioctl FBIOPUT_VSCREENINFO passing the fb_var_screeninfo struct containing only the fields xres, yres, and bits_per_pixel with values. If this struct is the same as the previous ioctl, the vc_resize() detects it and doesn't call the resize_screen(), leaving the fb_var_screeninfo incomplete. And this leads to the updatescrollmode() calculates a wrong value to fbcon_display->vrows, which makes the real_y() return a wrong value of y, and that value, eventually, causes the imageblit to access an out-of-bound address value. To solve this issue I made the resize_screen() be called even if the screen does not need any resizing, so it will "fix and fill" the fb_var_screeninfo independently.

In the Linux kernel, the following vulnerability has been resolved: net: qrtr: fix OOB Read in qrtr_endpoint_post Syzbot reported slab-out-of-bounds Read in qrtr_endpoint_post. The problem was in wrong _size_ type: if (len != ALIGN(size, 4) + hdrlen) goto err; If size from qrtr_hdr is 4294967293 (0xfffffffd), the result of ALIGN(size, 4) will be 0. In case of len == hdrlen and size == 4294967293 in header this check won't fail and skb_put_data(skb, data + hdrlen, size); will read out of bound from data, which is hdrlen allocated block.

In the Linux kernel, the following vulnerability has been resolved: iommu/arm-smmu: Fix arm_smmu_device refcount leak when arm_smmu_rpm_get fails arm_smmu_rpm_get() invokes pm_runtime_get_sync(), which increases the refcount of the "smmu" even though the return value is less than 0. The reference counting issue happens in some error handling paths of arm_smmu_rpm_get() in its caller functions. When arm_smmu_rpm_get() fails, the caller functions forget to decrease the refcount of "smmu" increased by arm_smmu_rpm_get(), causing a refcount leak. Fix this issue by calling pm_runtime_resume_and_get() instead of pm_runtime_get_sync() in arm_smmu_rpm_get(), which can keep the refcount balanced in case of failure.

In the Linux kernel, the following vulnerability has been resolved: media: ngene: Fix out-of-bounds bug in ngene_command_config_free_buf() Fix an 11-year old bug in ngene_command_config_free_buf() while addressing the following warnings caught with -Warray-bounds: arch/alpha/include/asm/string.h:22:16: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds] arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds] The problem is that the original code is trying to copy 6 bytes of data into a one-byte size member _config_ of the wrong structue FW_CONFIGURE_BUFFERS, in a single call to memcpy(). This causes a legitimate compiler warning because memcpy() overruns the length of &com.cmd.ConfigureBuffers.config. It seems that the right structure is FW_CONFIGURE_FREE_BUFFERS, instead, because it contains 6 more members apart from the header _hdr_. Also, the name of the function ngene_command_config_free_buf() suggests that the actual intention is to ConfigureFreeBuffers, instead of ConfigureBuffers (which takes place in the function ngene_command_config_buf(), above). Fix this by enclosing those 6 members of struct FW_CONFIGURE_FREE_BUFFERS into new struct config, and use &com.cmd.ConfigureFreeBuffers.config as the destination address, instead of &com.cmd.ConfigureBuffers.config, when calling memcpy(). This also helps with the ongoing efforts to globally enable -Warray-bounds and get us closer to being able to tighten the FORTIFY_SOURCE routines on memcpy().

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Fix stack-out-of-bounds memory access from ioapic_write_indirect() KASAN reports the following issue: BUG: KASAN: stack-out-of-bounds in kvm_make_vcpus_request_mask+0x174/0x440 [kvm] Read of size 8 at addr ffffc9001364f638 by task qemu-kvm/4798 CPU: 0 PID: 4798 Comm: qemu-kvm Tainted: G X --------- --- Hardware name: AMD Corporation DAYTONA_X/DAYTONA_X, BIOS RYM0081C 07/13/2020 Call Trace: dump_stack+0xa5/0xe6 print_address_description.constprop.0+0x18/0x130 ? kvm_make_vcpus_request_mask+0x174/0x440 [kvm] __kasan_report.cold+0x7f/0x114 ? kvm_make_vcpus_request_mask+0x174/0x440 [kvm] kasan_report+0x38/0x50 kasan_check_range+0xf5/0x1d0 kvm_make_vcpus_request_mask+0x174/0x440 [kvm] kvm_make_scan_ioapic_request_mask+0x84/0xc0 [kvm] ? kvm_arch_exit+0x110/0x110 [kvm] ? sched_clock+0x5/0x10 ioapic_write_indirect+0x59f/0x9e0 [kvm] ? static_obj+0xc0/0xc0 ? __lock_acquired+0x1d2/0x8c0 ? kvm_ioapic_eoi_inject_work+0x120/0x120 [kvm] The problem appears to be that 'vcpu_bitmap' is allocated as a single long on stack and it should really be KVM_MAX_VCPUS long. We also seem to clear the lower 16 bits of it with bitmap_zero() for no particular reason (my guess would be that 'bitmap' and 'vcpu_bitmap' variables in kvm_bitmap_or_dest_vcpus() caused the confusion: while the later is indeed 16-bit long, the later should accommodate all possible vCPUs).

In the Linux kernel, the following vulnerability has been resolved: net/sched: sch_frag: fix stack OOB read while fragmenting IPv4 packets when 'act_mirred' tries to fragment IPv4 packets that had been previously re-assembled using 'act_ct', splats like the following can be observed on kernels built with KASAN: BUG: KASAN: stack-out-of-bounds in ip_do_fragment+0x1b03/0x1f60 Read of size 1 at addr ffff888147009574 by task ping/947 CPU: 0 PID: 947 Comm: ping Not tainted 5.12.0-rc6+ #418 Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014 Call Trace: <IRQ> dump_stack+0x92/0xc1 print_address_description.constprop.7+0x1a/0x150 kasan_report.cold.13+0x7f/0x111 ip_do_fragment+0x1b03/0x1f60 sch_fragment+0x4bf/0xe40 tcf_mirred_act+0xc3d/0x11a0 [act_mirred] tcf_action_exec+0x104/0x3e0 fl_classify+0x49a/0x5e0 [cls_flower] tcf_classify_ingress+0x18a/0x820 __netif_receive_skb_core+0xae7/0x3340 __netif_receive_skb_one_core+0xb6/0x1b0 process_backlog+0x1ef/0x6c0 __napi_poll+0xaa/0x500 net_rx_action+0x702/0xac0 __do_softirq+0x1e4/0x97f do_softirq+0x71/0x90 </IRQ> __local_bh_enable_ip+0xdb/0xf0 ip_finish_output2+0x760/0x2120 ip_do_fragment+0x15a5/0x1f60 __ip_finish_output+0x4c2/0xea0 ip_output+0x1ca/0x4d0 ip_send_skb+0x37/0xa0 raw_sendmsg+0x1c4b/0x2d00 sock_sendmsg+0xdb/0x110 __sys_sendto+0x1d7/0x2b0 __x64_sys_sendto+0xdd/0x1b0 do_syscall_64+0x33/0x40 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f82e13853eb Code: 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 f3 0f 1e fa 48 8d 05 75 42 2c 00 41 89 ca 8b 00 85 c0 75 14 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 75 c3 0f 1f 40 00 41 57 4d 89 c7 41 56 41 89 RSP: 002b:00007ffe01fad888 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00005571aac13700 RCX: 00007f82e13853eb RDX: 0000000000002330 RSI: 00005571aac13700 RDI: 0000000000000003 RBP: 0000000000002330 R08: 00005571aac10500 R09: 0000000000000010 R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffe01faefb0 R13: 00007ffe01fad890 R14: 00007ffe01fad980 R15: 00005571aac0f0a0 The buggy address belongs to the page: page:000000001dff2e03 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x147009 flags: 0x17ffffc0001000(reserved) raw: 0017ffffc0001000 ffffea00051c0248 ffffea00051c0248 0000000000000000 raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888147009400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888147009480: f1 f1 f1 f1 04 f2 f2 f2 f2 f2 f2 f2 00 00 00 00 >ffff888147009500: 00 00 00 00 00 00 00 00 00 00 f2 f2 f2 f2 f2 f2 ^ ffff888147009580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888147009600: 00 00 00 00 00 00 00 00 00 00 00 00 00 f2 f2 f2 for IPv4 packets, sch_fragment() uses a temporary struct dst_entry. Then, in the following call graph: ip_do_fragment() ip_skb_dst_mtu() ip_dst_mtu_maybe_forward() ip_mtu_locked() the pointer to struct dst_entry is used as pointer to struct rtable: this turns the access to struct members like rt_mtu_locked into an OOB read in the stack. Fix this changing the temporary variable used for IPv4 packets in sch_fragment(), similarly to what is done for IPv6 few lines below.

In the Linux kernel, the following vulnerability has been resolved: usb: typec: ucsi: Retrieve all the PDOs instead of just the first 4 commit 4dbc6a4ef06d ("usb: typec: ucsi: save power data objects in PD mode") introduced retrieval of the PDOs when connected to a PD-capable source. But only the first 4 PDOs are received since that is the maximum number that can be fetched at a time given the MESSAGE_IN length limitation (16 bytes). However, as per the PD spec a connected source may advertise up to a maximum of 7 PDOs. If such a source is connected it's possible the PPM could have negotiated a power contract with one of the PDOs at index greater than 4, and would be reflected in the request data object's (RDO) object position field. This would result in an out-of-bounds access when the rdo_index() is used to index into the src_pdos array in ucsi_psy_get_voltage_now(). With the help of the UBSAN -fsanitize=array-bounds checker enabled this exact issue is revealed when connecting to a PD source adapter that advertise 5 PDOs and the PPM enters a contract having selected the 5th one. [ 151.545106][ T70] Unexpected kernel BRK exception at EL1 [ 151.545112][ T70] Internal error: BRK handler: f2005512 [#1] PREEMPT SMP ... [ 151.545499][ T70] pc : ucsi_psy_get_prop+0x208/0x20c [ 151.545507][ T70] lr : power_supply_show_property+0xc0/0x328 ... [ 151.545542][ T70] Call trace: [ 151.545544][ T70] ucsi_psy_get_prop+0x208/0x20c [ 151.545546][ T70] power_supply_uevent+0x1a4/0x2f0 [ 151.545550][ T70] dev_uevent+0x200/0x384 [ 151.545555][ T70] kobject_uevent_env+0x1d4/0x7e8 [ 151.545557][ T70] power_supply_changed_work+0x174/0x31c [ 151.545562][ T70] process_one_work+0x244/0x6f0 [ 151.545564][ T70] worker_thread+0x3e0/0xa64 We can resolve this by instead retrieving and storing up to the maximum of 7 PDOs in the con->src_pdos array. This would involve two calls to the GET_PDOS command.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix potential oob read in nilfs_btree_check_delete() The function nilfs_btree_check_delete(), which checks whether degeneration to direct mapping occurs before deleting a b-tree entry, causes memory access outside the block buffer when retrieving the maximum key if the root node has no entries. This does not usually happen because b-tree mappings with 0 child nodes are never created by mkfs.nilfs2 or nilfs2 itself. However, it can happen if the b-tree root node read from a device is configured that way, so fix this potential issue by adding a check for that case.

In the Linux kernel, the following vulnerability has been resolved: ataflop: potential out of bounds in do_format() The function uses "type" as an array index: q = unit[drive].disk[type]->queue; Unfortunately the bounds check on "type" isn't done until later in the function. Fix this by moving the bounds check to the start.

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Fix UBSAN shift-out-of-bounds warning If get_num_sdma_queues or get_num_xgmi_sdma_queues is 0, we end up doing a shift operation where the number of bits shifted equals number of bits in the operand. This behaviour is undefined. Set num_sdma_queues or num_xgmi_sdma_queues to ULLONG_MAX, if the count is >= number of bits in the operand. Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1472

In the Linux kernel, the following vulnerability has been resolved: net_sched: keep alloc_hash updated after hash allocation In commit 599be01ee567 ("net_sched: fix an OOB access in cls_tcindex") I moved cp->hash calculation before the first tcindex_alloc_perfect_hash(), but cp->alloc_hash is left untouched. This difference could lead to another out of bound access. cp->alloc_hash should always be the size allocated, we should update it after this tcindex_alloc_perfect_hash().

An out-of-bounds (OOB) memory access flaw was found in the Linux kernel's eBPF due to an Improper Input Validation. This flaw allows a local attacker with a special privilege to crash the system or leak internal information.

A use-after-free flaw was found in vcs_read in drivers/tty/vt/vc_screen.c in vc_screen in the Linux Kernel. This issue may allow an attacker with local user access to cause a system crash or leak internal kernel information.

In the Linux kernel, the following vulnerability has been resolved: scsi: bfa: Ensure the copied buf is NUL terminated Currently, we allocate a nbytes-sized kernel buffer and copy nbytes from userspace to that buffer. Later, we use sscanf on this buffer but we don't ensure that the string is terminated inside the buffer, this can lead to OOB read when using sscanf. Fix this issue by using memdup_user_nul instead of memdup_user.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix out-of-bound access of qmi_invoke_handler() Currently, there is no terminator entry for ath12k_qmi_msg_handlers hence facing below KASAN warning, ================================================================== BUG: KASAN: global-out-of-bounds in qmi_invoke_handler+0xa4/0x148 Read of size 8 at addr ffffffd00a6428d8 by task kworker/u8:2/1273 CPU: 0 PID: 1273 Comm: kworker/u8:2 Not tainted 5.4.213 #0 Workqueue: qmi_msg_handler qmi_data_ready_work Call trace: dump_backtrace+0x0/0x20c show_stack+0x14/0x1c dump_stack+0xe0/0x138 print_address_description.isra.5+0x30/0x330 __kasan_report+0x16c/0x1bc kasan_report+0xc/0x14 __asan_load8+0xa8/0xb0 qmi_invoke_handler+0xa4/0x148 qmi_handle_message+0x18c/0x1bc qmi_data_ready_work+0x4ec/0x528 process_one_work+0x2c0/0x440 worker_thread+0x324/0x4b8 kthread+0x210/0x228 ret_from_fork+0x10/0x18 The address belongs to the variable: ath12k_mac_mon_status_filter_default+0x4bd8/0xfffffffffffe2300 [ath12k] [...] ================================================================== Add a dummy terminator entry at the end to assist the qmi_invoke_handler() in traversing up to the terminator entry without accessing an out-of-boundary index. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

In the Linux kernel, the following vulnerability has been resolved: rcu: Fix buffer overflow in print_cpu_stall_info() The rcuc-starvation output from print_cpu_stall_info() might overflow the buffer if there is a huge difference in jiffies difference. The situation might seem improbable, but computers sometimes get very confused about time, which can result in full-sized integers, and, in this case, buffer overflow. Also, the unsigned jiffies difference is printed using %ld, which is normally for signed integers. This is intentional for debugging purposes, but it is not obvious from the code. This commit therefore changes sprintf() to snprintf() and adds a clarifying comment about intention of %ld format. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: enic: Validate length of nl attributes in enic_set_vf_port enic_set_vf_port assumes that the nl attribute IFLA_PORT_PROFILE is of length PORT_PROFILE_MAX and that the nl attributes IFLA_PORT_INSTANCE_UUID, IFLA_PORT_HOST_UUID are of length PORT_UUID_MAX. These attributes are validated (in the function do_setlink in rtnetlink.c) using the nla_policy ifla_port_policy. The policy defines IFLA_PORT_PROFILE as NLA_STRING, IFLA_PORT_INSTANCE_UUID as NLA_BINARY and IFLA_PORT_HOST_UUID as NLA_STRING. That means that the length validation using the policy is for the max size of the attributes and not on exact size so the length of these attributes might be less than the sizes that enic_set_vf_port expects. This might cause an out of bands read access in the memcpys of the data of these attributes in enic_set_vf_port.

An out-of-bounds (OOB) memory read flaw was found in the Qualcomm IPC router protocol in the Linux kernel. A missing sanity check allows a local attacker to gain access to out-of-bounds memory, leading to a system crash or a leak of internal kernel information. The highest threat from this vulnerability is to system availability.

An out of bounds (OOB) memory access flaw was found in the Linux kernel in relay_file_read_start_pos in kernel/relay.c in the relayfs. This flaw could allow a local attacker to crash the system or leak kernel internal information.

In the Linux kernel, the following vulnerability has been resolved: jffs2: prevent xattr node from overflowing the eraseblock Add a check to make sure that the requested xattr node size is no larger than the eraseblock minus the cleanmarker. Unlike the usual inode nodes, the xattr nodes aren't split into parts and spread across multiple eraseblocks, which means that a xattr node must not occupy more than one eraseblock. If the requested xattr value is too large, the xattr node can spill onto the next eraseblock, overwriting the nodes and causing errors such as: jffs2: argh. node added in wrong place at 0x0000b050(2) jffs2: nextblock 0x0000a000, expected at 0000b00c jffs2: error: (823) do_verify_xattr_datum: node CRC failed at 0x01e050, read=0xfc892c93, calc=0x000000 jffs2: notice: (823) jffs2_get_inode_nodes: Node header CRC failed at 0x01e00c. {848f,2fc4,0fef511f,59a3d171} jffs2: Node at 0x0000000c with length 0x00001044 would run over the end of the erase block jffs2: Perhaps the file system was created with the wrong erase size? jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000010: 0x1044 instead This breaks the filesystem and can lead to KASAN crashes such as: BUG: KASAN: slab-out-of-bounds in jffs2_sum_add_kvec+0x125e/0x15d0 Read of size 4 at addr ffff88802c31e914 by task repro/830 CPU: 0 PID: 830 Comm: repro Not tainted 6.9.0-rc3+ #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0xc6/0x120 print_report+0xc4/0x620 ? __virt_addr_valid+0x308/0x5b0 kasan_report+0xc1/0xf0 ? jffs2_sum_add_kvec+0x125e/0x15d0 ? jffs2_sum_add_kvec+0x125e/0x15d0 jffs2_sum_add_kvec+0x125e/0x15d0 jffs2_flash_direct_writev+0xa8/0xd0 jffs2_flash_writev+0x9c9/0xef0 ? __x64_sys_setxattr+0xc4/0x160 ? do_syscall_64+0x69/0x140 ? entry_SYSCALL_64_after_hwframe+0x76/0x7e [...] Found by Linux Verification Center (linuxtesting.org) with Syzkaller.

A use-after-free flaw was found in mt7921_check_offload_capability in drivers/net/wireless/mediatek/mt76/mt7921/init.c in wifi mt76/mt7921 sub-component in the Linux Kernel. This flaw could allow an attacker to crash the system after 'features' memory release. This vulnerability could even lead to a kernel information leak problem.

In the Linux kernel, the following vulnerability has been resolved: net: bridge: xmit: make sure we have at least eth header len bytes syzbot triggered an uninit value[1] error in bridge device's xmit path by sending a short (less than ETH_HLEN bytes) skb. To fix it check if we can actually pull that amount instead of assuming. Tested with dropwatch: drop at: br_dev_xmit+0xb93/0x12d0 [bridge] (0xffffffffc06739b3) origin: software timestamp: Mon May 13 11:31:53 2024 778214037 nsec protocol: 0x88a8 length: 2 original length: 2 drop reason: PKT_TOO_SMALL [1] BUG: KMSAN: uninit-value in br_dev_xmit+0x61d/0x1cb0 net/bridge/br_device.c:65 br_dev_xmit+0x61d/0x1cb0 net/bridge/br_device.c:65 __netdev_start_xmit include/linux/netdevice.h:4903 [inline] netdev_start_xmit include/linux/netdevice.h:4917 [inline] xmit_one net/core/dev.c:3531 [inline] dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3547 __dev_queue_xmit+0x34db/0x5350 net/core/dev.c:4341 dev_queue_xmit include/linux/netdevice.h:3091 [inline] __bpf_tx_skb net/core/filter.c:2136 [inline] __bpf_redirect_common net/core/filter.c:2180 [inline] __bpf_redirect+0x14a6/0x1620 net/core/filter.c:2187 ____bpf_clone_redirect net/core/filter.c:2460 [inline] bpf_clone_redirect+0x328/0x470 net/core/filter.c:2432 ___bpf_prog_run+0x13fe/0xe0f0 kernel/bpf/core.c:1997 __bpf_prog_run512+0xb5/0xe0 kernel/bpf/core.c:2238 bpf_dispatcher_nop_func include/linux/bpf.h:1234 [inline] __bpf_prog_run include/linux/filter.h:657 [inline] bpf_prog_run include/linux/filter.h:664 [inline] bpf_test_run+0x499/0xc30 net/bpf/test_run.c:425 bpf_prog_test_run_skb+0x14ea/0x1f20 net/bpf/test_run.c:1058 bpf_prog_test_run+0x6b7/0xad0 kernel/bpf/syscall.c:4269 __sys_bpf+0x6aa/0xd90 kernel/bpf/syscall.c:5678 __do_sys_bpf kernel/bpf/syscall.c:5767 [inline] __se_sys_bpf kernel/bpf/syscall.c:5765 [inline] __x64_sys_bpf+0xa0/0xe0 kernel/bpf/syscall.c:5765 x64_sys_call+0x96b/0x3b50 arch/x86/include/generated/asm/syscalls_64.h:322 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f

A use-after-free flaw was found in r592_remove in drivers/memstick/host/r592.c in media access in the Linux Kernel. This flaw allows a local attacker to crash the system at device disconnect, possibly leading to a kernel information leak.

In the Linux kernel, the following vulnerability has been resolved: blk-iocost: avoid out of bounds shift UBSAN catches undefined behavior in blk-iocost, where sometimes iocg->delay is shifted right by a number that is too large, resulting in undefined behavior on some architectures. [ 186.556576] ------------[ cut here ]------------ UBSAN: shift-out-of-bounds in block/blk-iocost.c:1366:23 shift exponent 64 is too large for 64-bit type 'u64' (aka 'unsigned long long') CPU: 16 PID: 0 Comm: swapper/16 Tainted: G S E N 6.9.0-0_fbk700_debug_rc2_kbuilder_0_gc85af715cac0 #1 Hardware name: Quanta Twin Lakes MP/Twin Lakes Passive MP, BIOS F09_3A23 12/08/2020 Call Trace: <IRQ> dump_stack_lvl+0x8f/0xe0 __ubsan_handle_shift_out_of_bounds+0x22c/0x280 iocg_kick_delay+0x30b/0x310 ioc_timer_fn+0x2fb/0x1f80 __run_timer_base+0x1b6/0x250 ... Avoid that undefined behavior by simply taking the "delay = 0" branch if the shift is too large. I am not sure what the symptoms of an undefined value delay will be, but I suspect it could be more than a little annoying to debug.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: RFCOMM: Fix not validating setsockopt user input syzbot reported rfcomm_sock_setsockopt_old() is copying data without checking user input length. BUG: KASAN: slab-out-of-bounds in copy_from_sockptr_offset include/linux/sockptr.h:49 [inline] BUG: KASAN: slab-out-of-bounds in copy_from_sockptr include/linux/sockptr.h:55 [inline] BUG: KASAN: slab-out-of-bounds in rfcomm_sock_setsockopt_old net/bluetooth/rfcomm/sock.c:632 [inline] BUG: KASAN: slab-out-of-bounds in rfcomm_sock_setsockopt+0x893/0xa70 net/bluetooth/rfcomm/sock.c:673 Read of size 4 at addr ffff8880209a8bc3 by task syz-executor632/5064

A NULL pointer dereference flaw was found in the btrfs_rm_device function in fs/btrfs/volumes.c in the Linux Kernel, where triggering the bug requires ‘CAP_SYS_ADMIN’. This flaw allows a local attacker to crash the system or leak kernel internal information. The highest threat from this vulnerability is to system availability.

In the Linux kernel, the following vulnerability has been resolved: tracing: Fix wild-memory-access in register_synth_event() In register_synth_event(), if set_synth_event_print_fmt() failed, then both trace_remove_event_call() and unregister_trace_event() will be called, which means the trace_event_call will call __unregister_trace_event() twice. As the result, the second unregister will causes the wild-memory-access. register_synth_event set_synth_event_print_fmt failed trace_remove_event_call event_remove if call->event.funcs then __unregister_trace_event (first call) unregister_trace_event __unregister_trace_event (second call) Fix the bug by avoiding to call the second __unregister_trace_event() by checking if the first one is called. general protection fault, probably for non-canonical address 0xfbd59c0000000024: 0000 [#1] SMP KASAN PTI KASAN: maybe wild-memory-access in range [0xdead000000000120-0xdead000000000127] CPU: 0 PID: 3807 Comm: modprobe Not tainted 6.1.0-rc1-00186-g76f33a7eedb4 #299 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014 RIP: 0010:unregister_trace_event+0x6e/0x280 Code: 00 fc ff df 4c 89 ea 48 c1 ea 03 80 3c 02 00 0f 85 0e 02 00 00 48 b8 00 00 00 00 00 fc ff df 4c 8b 63 08 4c 89 e2 48 c1 ea 03 <80> 3c 02 00 0f 85 e2 01 00 00 49 89 2c 24 48 85 ed 74 28 e8 7a 9b RSP: 0018:ffff88810413f370 EFLAGS: 00010a06 RAX: dffffc0000000000 RBX: ffff888105d050b0 RCX: 0000000000000000 RDX: 1bd5a00000000024 RSI: ffff888119e276e0 RDI: ffffffff835a8b20 RBP: dead000000000100 R08: 0000000000000000 R09: fffffbfff0913481 R10: ffffffff8489a407 R11: fffffbfff0913480 R12: dead000000000122 R13: ffff888105d050b8 R14: 0000000000000000 R15: ffff888105d05028 FS: 00007f7823e8d540(0000) GS:ffff888119e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7823e7ebec CR3: 000000010a058002 CR4: 0000000000330ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __create_synth_event+0x1e37/0x1eb0 create_or_delete_synth_event+0x110/0x250 synth_event_run_command+0x2f/0x110 test_gen_synth_cmd+0x170/0x2eb [synth_event_gen_test] synth_event_gen_test_init+0x76/0x9bc [synth_event_gen_test] do_one_initcall+0xdb/0x480 do_init_module+0x1cf/0x680 load_module+0x6a50/0x70a0 __do_sys_finit_module+0x12f/0x1c0 do_syscall_64+0x3f/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd

In the Linux kernel, the following vulnerability has been resolved: tee: optee: Fix kernel panic caused by incorrect error handling The error path while failing to register devices on the TEE bus has a bug leading to kernel panic as follows: [ 15.398930] Unable to handle kernel paging request at virtual address ffff07ed00626d7c [ 15.406913] Mem abort info: [ 15.409722] ESR = 0x0000000096000005 [ 15.413490] EC = 0x25: DABT (current EL), IL = 32 bits [ 15.418814] SET = 0, FnV = 0 [ 15.421878] EA = 0, S1PTW = 0 [ 15.425031] FSC = 0x05: level 1 translation fault [ 15.429922] Data abort info: [ 15.432813] ISV = 0, ISS = 0x00000005, ISS2 = 0x00000000 [ 15.438310] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 15.443372] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 15.448697] swapper pgtable: 4k pages, 48-bit VAs, pgdp=00000000d9e3e000 [ 15.455413] [ffff07ed00626d7c] pgd=1800000bffdf9003, p4d=1800000bffdf9003, pud=0000000000000000 [ 15.464146] Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP Commit 7269cba53d90 ("tee: optee: Fix supplicant based device enumeration") lead to the introduction of this bug. So fix it appropriately.

In the Linux kernel, the following vulnerability has been resolved: media: i2c: max9286: fix kernel oops when removing module When removing the max9286 module we get a kernel oops: Unable to handle kernel paging request at virtual address 000000aa00000094 Mem abort info: ESR = 0x96000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004 CM = 0, WnR = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=0000000880d85000 [000000aa00000094] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 96000004 [#1] PREEMPT SMP Modules linked in: fsl_jr_uio caam_jr rng_core libdes caamkeyblob_desc caamhash_desc caamalg_desc crypto_engine max9271 authenc crct10dif_ce mxc_jpeg_encdec CPU: 2 PID: 713 Comm: rmmod Tainted: G C 5.15.5-00057-gaebcd29c8ed7-dirty #5 Hardware name: Freescale i.MX8QXP MEK (DT) pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : i2c_mux_del_adapters+0x24/0xf0 lr : max9286_remove+0x28/0xd0 [max9286] sp : ffff800013a9bbf0 x29: ffff800013a9bbf0 x28: ffff00080b6da940 x27: 0000000000000000 x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000000 x23: ffff000801a5b970 x22: ffff0008048b0890 x21: ffff800009297000 x20: ffff0008048b0f70 x19: 000000aa00000064 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000014 x13: 0000000000000000 x12: ffff000802da49e8 x11: ffff000802051918 x10: ffff000802da4920 x9 : ffff000800030098 x8 : 0101010101010101 x7 : 7f7f7f7f7f7f7f7f x6 : fefefeff6364626d x5 : 8080808000000000 x4 : 0000000000000000 x3 : 0000000000000000 x2 : ffffffffffffffff x1 : ffff00080b6da940 x0 : 0000000000000000 Call trace: i2c_mux_del_adapters+0x24/0xf0 max9286_remove+0x28/0xd0 [max9286] i2c_device_remove+0x40/0x110 __device_release_driver+0x188/0x234 driver_detach+0xc4/0x150 bus_remove_driver+0x60/0xe0 driver_unregister+0x34/0x64 i2c_del_driver+0x58/0xa0 max9286_i2c_driver_exit+0x1c/0x490 [max9286] __arm64_sys_delete_module+0x194/0x260 invoke_syscall+0x48/0x114 el0_svc_common.constprop.0+0xd4/0xfc do_el0_svc+0x2c/0x94 el0_svc+0x28/0x80 el0t_64_sync_handler+0xa8/0x130 el0t_64_sync+0x1a0/0x1a4 The Oops happens because the I2C client data does not point to max9286_priv anymore but to v4l2_subdev. The change happened in max9286_init() which calls v4l2_i2c_subdev_init() later on... Besides fixing the max9286_remove() function, remove the call to i2c_set_clientdata() in max9286_probe(), to avoid confusion, and make the necessary changes to max9286_init() so that it doesn't have to use i2c_get_clientdata() in order to fetch the pointer to priv.

An out-of-bounds (OOB) memory access flaw was found in fs/f2fs/node.c in the f2fs module in the Linux kernel in versions before 5.12.0-rc4. A bounds check failure allows a local attacker to gain access to out-of-bounds memory leading to a system crash or a leak of internal kernel information. The highest threat from this vulnerability is to system availability.

In the Linux kernel, the following vulnerability has been resolved: ath5k: fix OOB in ath5k_eeprom_read_pcal_info_5111 The bug was found during fuzzing. Stacktrace locates it in ath5k_eeprom_convert_pcal_info_5111. When none of the curve is selected in the loop, idx can go up to AR5K_EEPROM_N_PD_CURVES. The line makes pd out of bound. pd = &chinfo[pier].pd_curves[idx]; There are many OOB writes using pd later in the code. So I added a sanity check for idx. Checks for other loops involving AR5K_EEPROM_N_PD_CURVES are not needed as the loop index is not used outside the loops. The patch is NOT tested with real device. The following is the fuzzing report BUG: KASAN: slab-out-of-bounds in ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] Write of size 1 at addr ffff8880174a4d60 by task modprobe/214 CPU: 0 PID: 214 Comm: modprobe Not tainted 5.6.0 #1 Call Trace: dump_stack+0x76/0xa0 print_address_description.constprop.0+0x16/0x200 ? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] ? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] __kasan_report.cold+0x37/0x7c ? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] kasan_report+0xe/0x20 ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] ? apic_timer_interrupt+0xa/0x20 ? ath5k_eeprom_init_11a_pcal_freq+0xbc0/0xbc0 [ath5k] ? ath5k_pci_eeprom_read+0x228/0x3c0 [ath5k] ath5k_eeprom_init+0x2513/0x6290 [ath5k] ? ath5k_eeprom_init_11a_pcal_freq+0xbc0/0xbc0 [ath5k] ? usleep_range+0xb8/0x100 ? apic_timer_interrupt+0xa/0x20 ? ath5k_eeprom_read_pcal_info_2413+0x2f20/0x2f20 [ath5k] ath5k_hw_init+0xb60/0x1970 [ath5k] ath5k_init_ah+0x6fe/0x2530 [ath5k] ? kasprintf+0xa6/0xe0 ? ath5k_stop+0x140/0x140 [ath5k] ? _dev_notice+0xf6/0xf6 ? apic_timer_interrupt+0xa/0x20 ath5k_pci_probe.cold+0x29a/0x3d6 [ath5k] ? ath5k_pci_eeprom_read+0x3c0/0x3c0 [ath5k] ? mutex_lock+0x89/0xd0 ? ath5k_pci_eeprom_read+0x3c0/0x3c0 [ath5k] local_pci_probe+0xd3/0x160 pci_device_probe+0x23f/0x3e0 ? pci_device_remove+0x280/0x280 ? pci_device_remove+0x280/0x280 really_probe+0x209/0x5d0

In the Linux kernel, the following vulnerability has been resolved: sch_cake: Fix out of bounds when parsing TCP options and header The TCP option parser in cake qdisc (cake_get_tcpopt and cake_tcph_may_drop) could read one byte out of bounds. When the length is 1, the execution flow gets into the loop, reads one byte of the opcode, and if the opcode is neither TCPOPT_EOL nor TCPOPT_NOP, it reads one more byte, which exceeds the length of 1. This fix is inspired by commit 9609dad263f8 ("ipv4: tcp_input: fix stack out of bounds when parsing TCP options."). v2 changes: Added doff validation in cake_get_tcphdr to avoid parsing garbage as TCP header. Although it wasn't strictly an out-of-bounds access (memory was allocated), garbage values could be read where CAKE expected the TCP header if doff was smaller than 5.

In the Linux kernel, the following vulnerability has been resolved: drm/i915/sseu: fix max_subslices array-index-out-of-bounds access It seems that commit bc3c5e0809ae ("drm/i915/sseu: Don't try to store EU mask internally in UAPI format") exposed a potential out-of-bounds access, reported by UBSAN as following on a laptop with a gen 11 i915 card: UBSAN: array-index-out-of-bounds in drivers/gpu/drm/i915/gt/intel_sseu.c:65:27 index 6 is out of range for type 'u16 [6]' CPU: 2 PID: 165 Comm: systemd-udevd Not tainted 6.2.0-9-generic #9-Ubuntu Hardware name: Dell Inc. XPS 13 9300/077Y9N, BIOS 1.11.0 03/22/2022 Call Trace: <TASK> show_stack+0x4e/0x61 dump_stack_lvl+0x4a/0x6f dump_stack+0x10/0x18 ubsan_epilogue+0x9/0x3a __ubsan_handle_out_of_bounds.cold+0x42/0x47 gen11_compute_sseu_info+0x121/0x130 [i915] intel_sseu_info_init+0x15d/0x2b0 [i915] intel_gt_init_mmio+0x23/0x40 [i915] i915_driver_mmio_probe+0x129/0x400 [i915] ? intel_gt_probe_all+0x91/0x2e0 [i915] i915_driver_probe+0xe1/0x3f0 [i915] ? drm_privacy_screen_get+0x16d/0x190 [drm] ? acpi_dev_found+0x64/0x80 i915_pci_probe+0xac/0x1b0 [i915] ... According to the definition of sseu_dev_info, eu_mask->hsw is limited to a maximum of GEN_MAX_SS_PER_HSW_SLICE (6) sub-slices, but gen11_sseu_info_init() can potentially set 8 sub-slices, in the !IS_JSL_EHL(gt->i915) case. Fix this by reserving up to 8 slots for max_subslices in the eu_mask struct. (cherry picked from commit 3cba09a6ac86ea1d456909626eb2685596c07822)

In the Linux kernel, the following vulnerability has been resolved: net: use a bounce buffer for copying skb->mark syzbot found arm64 builds would crash in sock_recv_mark() when CONFIG_HARDENED_USERCOPY=y x86 and powerpc are not detecting the issue because they define user_access_begin. This will be handled in a different patch, because a check_object_size() is missing. Only data from skb->cb[] can be copied directly to/from user space, as explained in commit 79a8a642bf05 ("net: Whitelist the skbuff_head_cache "cb" field") syzbot report was: usercopy: Kernel memory exposure attempt detected from SLUB object 'skbuff_head_cache' (offset 168, size 4)! ------------[ cut here ]------------ kernel BUG at mm/usercopy.c:102 ! Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP Modules linked in: CPU: 0 PID: 4410 Comm: syz-executor533 Not tainted 6.2.0-rc7-syzkaller-17907-g2d3827b3f393 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/21/2023 pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : usercopy_abort+0x90/0x94 mm/usercopy.c:90 lr : usercopy_abort+0x90/0x94 mm/usercopy.c:90 sp : ffff80000fb9b9a0 x29: ffff80000fb9b9b0 x28: ffff0000c6073400 x27: 0000000020001a00 x26: 0000000000000014 x25: ffff80000cf52000 x24: fffffc0000000000 x23: 05ffc00000000200 x22: fffffc000324bf80 x21: ffff0000c92fe1a8 x20: 0000000000000001 x19: 0000000000000004 x18: 0000000000000000 x17: 656a626f2042554c x16: ffff0000c6073dd0 x15: ffff80000dbd2118 x14: ffff0000c6073400 x13: 00000000ffffffff x12: ffff0000c6073400 x11: ff808000081bbb4c x10: 0000000000000000 x9 : 7b0572d7cc0ccf00 x8 : 7b0572d7cc0ccf00 x7 : ffff80000bf650d4 x6 : 0000000000000000 x5 : 0000000000000001 x4 : 0000000000000001 x3 : 0000000000000000 x2 : ffff0001fefbff08 x1 : 0000000100000000 x0 : 000000000000006c Call trace: usercopy_abort+0x90/0x94 mm/usercopy.c:90 __check_heap_object+0xa8/0x100 mm/slub.c:4761 check_heap_object mm/usercopy.c:196 [inline] __check_object_size+0x208/0x6b8 mm/usercopy.c:251 check_object_size include/linux/thread_info.h:199 [inline] __copy_to_user include/linux/uaccess.h:115 [inline] put_cmsg+0x408/0x464 net/core/scm.c:238 sock_recv_mark net/socket.c:975 [inline] __sock_recv_cmsgs+0x1fc/0x248 net/socket.c:984 sock_recv_cmsgs include/net/sock.h:2728 [inline] packet_recvmsg+0x2d8/0x678 net/packet/af_packet.c:3482 ____sys_recvmsg+0x110/0x3a0 ___sys_recvmsg net/socket.c:2737 [inline] __sys_recvmsg+0x194/0x210 net/socket.c:2767 __do_sys_recvmsg net/socket.c:2777 [inline] __se_sys_recvmsg net/socket.c:2774 [inline] __arm64_sys_recvmsg+0x2c/0x3c net/socket.c:2774 __invoke_syscall arch/arm64/kernel/syscall.c:38 [inline] invoke_syscall+0x64/0x178 arch/arm64/kernel/syscall.c:52 el0_svc_common+0xbc/0x180 arch/arm64/kernel/syscall.c:142 do_el0_svc+0x48/0x110 arch/arm64/kernel/syscall.c:193 el0_svc+0x58/0x14c arch/arm64/kernel/entry-common.c:637 el0t_64_sync_handler+0x84/0xf0 arch/arm64/kernel/entry-common.c:655 el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:591 Code: 91388800 aa0903e1 f90003e8 94e6d752 (d4210000)

In the Linux kernel, the following vulnerability has been resolved: net: validate lwtstate->data before returning from skb_tunnel_info() skb_tunnel_info() returns pointer of lwtstate->data as ip_tunnel_info type without validation. lwtstate->data can have various types such as mpls_iptunnel_encap, etc and these are not compatible. So skb_tunnel_info() should validate before returning that pointer. Splat looks like: BUG: KASAN: slab-out-of-bounds in vxlan_get_route+0x418/0x4b0 [vxlan] Read of size 2 at addr ffff888106ec2698 by task ping/811 CPU: 1 PID: 811 Comm: ping Not tainted 5.13.0+ #1195 Call Trace: dump_stack_lvl+0x56/0x7b print_address_description.constprop.8.cold.13+0x13/0x2ee ? vxlan_get_route+0x418/0x4b0 [vxlan] ? vxlan_get_route+0x418/0x4b0 [vxlan] kasan_report.cold.14+0x83/0xdf ? vxlan_get_route+0x418/0x4b0 [vxlan] vxlan_get_route+0x418/0x4b0 [vxlan] [ ... ] vxlan_xmit_one+0x148b/0x32b0 [vxlan] [ ... ] vxlan_xmit+0x25c5/0x4780 [vxlan] [ ... ] dev_hard_start_xmit+0x1ae/0x6e0 __dev_queue_xmit+0x1f39/0x31a0 [ ... ] neigh_xmit+0x2f9/0x940 mpls_xmit+0x911/0x1600 [mpls_iptunnel] lwtunnel_xmit+0x18f/0x450 ip_finish_output2+0x867/0x2040 [ ... ]

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Ensure liveliness of nested VM-Enter fail tracepoint message Use the __string() machinery provided by the tracing subystem to make a copy of the string literals consumed by the "nested VM-Enter failed" tracepoint. A complete copy is necessary to ensure that the tracepoint can't outlive the data/memory it consumes and deference stale memory. Because the tracepoint itself is defined by kvm, if kvm-intel and/or kvm-amd are built as modules, the memory holding the string literals defined by the vendor modules will be freed when the module is unloaded, whereas the tracepoint and its data in the ring buffer will live until kvm is unloaded (or "indefinitely" if kvm is built-in). This bug has existed since the tracepoint was added, but was recently exposed by a new check in tracing to detect exactly this type of bug. fmt: '%s%s ' current_buffer: ' vmx_dirty_log_t-140127 [003] .... kvm_nested_vmenter_failed: ' WARNING: CPU: 3 PID: 140134 at kernel/trace/trace.c:3759 trace_check_vprintf+0x3be/0x3e0 CPU: 3 PID: 140134 Comm: less Not tainted 5.13.0-rc1-ce2e73ce600a-req #184 Hardware name: ASUS Q87M-E/Q87M-E, BIOS 1102 03/03/2014 RIP: 0010:trace_check_vprintf+0x3be/0x3e0 Code: <0f> 0b 44 8b 4c 24 1c e9 a9 fe ff ff c6 44 02 ff 00 49 8b 97 b0 20 RSP: 0018:ffffa895cc37bcb0 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffffa895cc37bd08 RCX: 0000000000000027 RDX: 0000000000000027 RSI: 00000000ffffdfff RDI: ffff9766cfad74f8 RBP: ffffffffc0a041d4 R08: ffff9766cfad74f0 R09: ffffa895cc37bad8 R10: 0000000000000001 R11: 0000000000000001 R12: ffffffffc0a041d4 R13: ffffffffc0f4dba8 R14: 0000000000000000 R15: ffff976409f2c000 FS: 00007f92fa200740(0000) GS:ffff9766cfac0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000559bd11b0000 CR3: 000000019fbaa002 CR4: 00000000001726e0 Call Trace: trace_event_printf+0x5e/0x80 trace_raw_output_kvm_nested_vmenter_failed+0x3a/0x60 [kvm] print_trace_line+0x1dd/0x4e0 s_show+0x45/0x150 seq_read_iter+0x2d5/0x4c0 seq_read+0x106/0x150 vfs_read+0x98/0x180 ksys_read+0x5f/0xe0 do_syscall_64+0x40/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae

In the Linux kernel, the following vulnerability has been resolved: net: dsa: mt7530: fix VLAN traffic leaks PCR_MATRIX field was set to all 1's when VLAN filtering is enabled, but was not reset when it is disabled, which may cause traffic leaks: ip link add br0 type bridge vlan_filtering 1 ip link add br1 type bridge vlan_filtering 1 ip link set swp0 master br0 ip link set swp1 master br1 ip link set br0 type bridge vlan_filtering 0 ip link set br1 type bridge vlan_filtering 0 # traffic in br0 and br1 will start leaking to each other As port_bridge_{add,del} have set up PCR_MATRIX properly, remove the PCR_MATRIX write from mt7530_port_set_vlan_aware.

In the Linux kernel, the following vulnerability has been resolved: cxgb4: avoid accessing registers when clearing filters Hardware register having the server TID base can contain invalid values when adapter is in bad state (for example, due to AER fatal error). Reading these invalid values in the register can lead to out-of-bound memory access. So, fix by using the saved server TID base when clearing filters.

In the Linux kernel, the following vulnerability has been resolved: KVM: x86/mmu: Don't advance iterator after restart due to yielding After dropping mmu_lock in the TDP MMU, restart the iterator during tdp_iter_next() and do not advance the iterator. Advancing the iterator results in skipping the top-level SPTE and all its children, which is fatal if any of the skipped SPTEs were not visited before yielding. When zapping all SPTEs, i.e. when min_level == root_level, restarting the iter and then invoking tdp_iter_next() is always fatal if the current gfn has as a valid SPTE, as advancing the iterator results in try_step_side() skipping the current gfn, which wasn't visited before yielding. Sprinkle WARNs on iter->yielded being true in various helpers that are often used in conjunction with yielding, and tag the helper with __must_check to reduce the probabily of improper usage. Failing to zap a top-level SPTE manifests in one of two ways. If a valid SPTE is skipped by both kvm_tdp_mmu_zap_all() and kvm_tdp_mmu_put_root(), the shadow page will be leaked and KVM will WARN accordingly. WARNING: CPU: 1 PID: 3509 at arch/x86/kvm/mmu/tdp_mmu.c:46 [kvm] RIP: 0010:kvm_mmu_uninit_tdp_mmu+0x3e/0x50 [kvm] Call Trace: <TASK> kvm_arch_destroy_vm+0x130/0x1b0 [kvm] kvm_destroy_vm+0x162/0x2a0 [kvm] kvm_vcpu_release+0x34/0x60 [kvm] __fput+0x82/0x240 task_work_run+0x5c/0x90 do_exit+0x364/0xa10 ? futex_unqueue+0x38/0x60 do_group_exit+0x33/0xa0 get_signal+0x155/0x850 arch_do_signal_or_restart+0xed/0x750 exit_to_user_mode_prepare+0xc5/0x120 syscall_exit_to_user_mode+0x1d/0x40 do_syscall_64+0x48/0xc0 entry_SYSCALL_64_after_hwframe+0x44/0xae If kvm_tdp_mmu_zap_all() skips a gfn/SPTE but that SPTE is then zapped by kvm_tdp_mmu_put_root(), KVM triggers a use-after-free in the form of marking a struct page as dirty/accessed after it has been put back on the free list. This directly triggers a WARN due to encountering a page with page_count() == 0, but it can also lead to data corruption and additional errors in the kernel. WARNING: CPU: 7 PID: 1995658 at arch/x86/kvm/../../../virt/kvm/kvm_main.c:171 RIP: 0010:kvm_is_zone_device_pfn.part.0+0x9e/0xd0 [kvm] Call Trace: <TASK> kvm_set_pfn_dirty+0x120/0x1d0 [kvm] __handle_changed_spte+0x92e/0xca0 [kvm] __handle_changed_spte+0x63c/0xca0 [kvm] __handle_changed_spte+0x63c/0xca0 [kvm] __handle_changed_spte+0x63c/0xca0 [kvm] zap_gfn_range+0x549/0x620 [kvm] kvm_tdp_mmu_put_root+0x1b6/0x270 [kvm] mmu_free_root_page+0x219/0x2c0 [kvm] kvm_mmu_free_roots+0x1b4/0x4e0 [kvm] kvm_mmu_unload+0x1c/0xa0 [kvm] kvm_arch_destroy_vm+0x1f2/0x5c0 [kvm] kvm_put_kvm+0x3b1/0x8b0 [kvm] kvm_vcpu_release+0x4e/0x70 [kvm] __fput+0x1f7/0x8c0 task_work_run+0xf8/0x1a0 do_exit+0x97b/0x2230 do_group_exit+0xda/0x2a0 get_signal+0x3be/0x1e50 arch_do_signal_or_restart+0x244/0x17f0 exit_to_user_mode_prepare+0xcb/0x120 syscall_exit_to_user_mode+0x1d/0x40 do_syscall_64+0x4d/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae Note, the underlying bug existed even before commit 1af4a96025b3 ("KVM: x86/mmu: Yield in TDU MMU iter even if no SPTES changed") moved calls to tdp_mmu_iter_cond_resched() to the beginning of loops, as KVM could still incorrectly advance past a top-level entry when yielding on a lower-level entry. But with respect to leaking shadow pages, the bug was introduced by yielding before processing the current gfn. Alternatively, tdp_mmu_iter_cond_resched() could simply fall through, or callers could jump to their "retry" label. The downside of that approach is that tdp_mmu_iter_cond_resched() _must_ be called before anything else in the loop, and there's no easy way to enfornce that requirement. Ideally, KVM would handling the cond_resched() fully within the iterator macro (the code is actually quite clean) and avoid this entire class of bugs, but that is extremely difficult do wh ---truncated---

In the Linux kernel, the following vulnerability has been resolved: Input: elantech - fix stack out of bound access in elantech_change_report_id() The array param[] in elantech_change_report_id() must be at least 3 bytes, because elantech_read_reg_params() is calling ps2_command() with PSMOUSE_CMD_GETINFO, that is going to access 3 bytes from param[], but it's defined in the stack as an array of 2 bytes, therefore we have a potential stack out-of-bounds access here, also confirmed by KASAN: [ 6.512374] BUG: KASAN: stack-out-of-bounds in __ps2_command+0x372/0x7e0 [ 6.512397] Read of size 1 at addr ffff8881024d77c2 by task kworker/2:1/118 [ 6.512416] CPU: 2 PID: 118 Comm: kworker/2:1 Not tainted 5.13.0-22-generic #22+arighi20211110 [ 6.512428] Hardware name: LENOVO 20T8000QGE/20T8000QGE, BIOS R1AET32W (1.08 ) 08/14/2020 [ 6.512436] Workqueue: events_long serio_handle_event [ 6.512453] Call Trace: [ 6.512462] show_stack+0x52/0x58 [ 6.512474] dump_stack+0xa1/0xd3 [ 6.512487] print_address_description.constprop.0+0x1d/0x140 [ 6.512502] ? __ps2_command+0x372/0x7e0 [ 6.512516] __kasan_report.cold+0x7d/0x112 [ 6.512527] ? _raw_write_lock_irq+0x20/0xd0 [ 6.512539] ? __ps2_command+0x372/0x7e0 [ 6.512552] kasan_report+0x3c/0x50 [ 6.512564] __asan_load1+0x6a/0x70 [ 6.512575] __ps2_command+0x372/0x7e0 [ 6.512589] ? ps2_drain+0x240/0x240 [ 6.512601] ? dev_printk_emit+0xa2/0xd3 [ 6.512612] ? dev_vprintk_emit+0xc5/0xc5 [ 6.512621] ? __kasan_check_write+0x14/0x20 [ 6.512634] ? mutex_lock+0x8f/0xe0 [ 6.512643] ? __mutex_lock_slowpath+0x20/0x20 [ 6.512655] ps2_command+0x52/0x90 [ 6.512670] elantech_ps2_command+0x4f/0xc0 [psmouse] [ 6.512734] elantech_change_report_id+0x1e6/0x256 [psmouse] [ 6.512799] ? elantech_report_trackpoint.constprop.0.cold+0xd/0xd [psmouse] [ 6.512863] ? ps2_command+0x7f/0x90 [ 6.512877] elantech_query_info.cold+0x6bd/0x9ed [psmouse] [ 6.512943] ? elantech_setup_ps2+0x460/0x460 [psmouse] [ 6.513005] ? psmouse_reset+0x69/0xb0 [psmouse] [ 6.513064] ? psmouse_attr_set_helper+0x2a0/0x2a0 [psmouse] [ 6.513122] ? phys_pmd_init+0x30e/0x521 [ 6.513137] elantech_init+0x8a/0x200 [psmouse] [ 6.513200] ? elantech_init_ps2+0xf0/0xf0 [psmouse] [ 6.513249] ? elantech_query_info+0x440/0x440 [psmouse] [ 6.513296] ? synaptics_send_cmd+0x60/0x60 [psmouse] [ 6.513342] ? elantech_query_info+0x440/0x440 [psmouse] [ 6.513388] ? psmouse_try_protocol+0x11e/0x170 [psmouse] [ 6.513432] psmouse_extensions+0x65d/0x6e0 [psmouse] [ 6.513476] ? psmouse_try_protocol+0x170/0x170 [psmouse] [ 6.513519] ? mutex_unlock+0x22/0x40 [ 6.513526] ? ps2_command+0x7f/0x90 [ 6.513536] ? psmouse_probe+0xa3/0xf0 [psmouse] [ 6.513580] psmouse_switch_protocol+0x27d/0x2e0 [psmouse] [ 6.513624] psmouse_connect+0x272/0x530 [psmouse] [ 6.513669] serio_driver_probe+0x55/0x70 [ 6.513679] really_probe+0x190/0x720 [ 6.513689] driver_probe_device+0x160/0x1f0 [ 6.513697] device_driver_attach+0x119/0x130 [ 6.513705] ? device_driver_attach+0x130/0x130 [ 6.513713] __driver_attach+0xe7/0x1a0 [ 6.513720] ? device_driver_attach+0x130/0x130 [ 6.513728] bus_for_each_dev+0xfb/0x150 [ 6.513738] ? subsys_dev_iter_exit+0x10/0x10 [ 6.513748] ? _raw_write_unlock_bh+0x30/0x30 [ 6.513757] driver_attach+0x2d/0x40 [ 6.513764] serio_handle_event+0x199/0x3d0 [ 6.513775] process_one_work+0x471/0x740 [ 6.513785] worker_thread+0x2d2/0x790 [ 6.513794] ? process_one_work+0x740/0x740 [ 6.513802] kthread+0x1b4/0x1e0 [ 6.513809] ? set_kthread_struct+0x80/0x80 [ 6.513816] ret_from_fork+0x22/0x30 [ 6.513832] The buggy address belongs to the page: [ 6.513838] page:00000000bc35e189 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1024d7 [ 6.513847] flags: 0x17ffffc0000000(node=0|zone=2|lastcpupid=0x1fffff) [ 6.513860] raw: 0 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: vduse: check that offset is within bounds in get_config() This condition checks "len" but it does not check "offset" and that could result in an out of bounds read if "offset > dev->config_size". The problem is that since both variables are unsigned the "dev->config_size - offset" subtraction would result in a very high unsigned value. I think these checks might not be necessary because "len" and "offset" are supposed to already have been validated using the vhost_vdpa_config_validate() function. But I do not know the code perfectly, and I like to be safe.

In the Linux kernel, the following vulnerability has been resolved: ipv6: addrlabel: fix infoleak when sending struct ifaddrlblmsg to network When copying a `struct ifaddrlblmsg` to the network, __ifal_reserved remained uninitialized, resulting in a 1-byte infoleak: BUG: KMSAN: kernel-network-infoleak in __netdev_start_xmit ./include/linux/netdevice.h:4841 __netdev_start_xmit ./include/linux/netdevice.h:4841 netdev_start_xmit ./include/linux/netdevice.h:4857 xmit_one net/core/dev.c:3590 dev_hard_start_xmit+0x1dc/0x800 net/core/dev.c:3606 __dev_queue_xmit+0x17e8/0x4350 net/core/dev.c:4256 dev_queue_xmit ./include/linux/netdevice.h:3009 __netlink_deliver_tap_skb net/netlink/af_netlink.c:307 __netlink_deliver_tap+0x728/0xad0 net/netlink/af_netlink.c:325 netlink_deliver_tap net/netlink/af_netlink.c:338 __netlink_sendskb net/netlink/af_netlink.c:1263 netlink_sendskb+0x1d9/0x200 net/netlink/af_netlink.c:1272 netlink_unicast+0x56d/0xf50 net/netlink/af_netlink.c:1360 nlmsg_unicast ./include/net/netlink.h:1061 rtnl_unicast+0x5a/0x80 net/core/rtnetlink.c:758 ip6addrlbl_get+0xfad/0x10f0 net/ipv6/addrlabel.c:628 rtnetlink_rcv_msg+0xb33/0x1570 net/core/rtnetlink.c:6082 ... Uninit was created at: slab_post_alloc_hook+0x118/0xb00 mm/slab.h:742 slab_alloc_node mm/slub.c:3398 __kmem_cache_alloc_node+0x4f2/0x930 mm/slub.c:3437 __do_kmalloc_node mm/slab_common.c:954 __kmalloc_node_track_caller+0x117/0x3d0 mm/slab_common.c:975 kmalloc_reserve net/core/skbuff.c:437 __alloc_skb+0x27a/0xab0 net/core/skbuff.c:509 alloc_skb ./include/linux/skbuff.h:1267 nlmsg_new ./include/net/netlink.h:964 ip6addrlbl_get+0x490/0x10f0 net/ipv6/addrlabel.c:608 rtnetlink_rcv_msg+0xb33/0x1570 net/core/rtnetlink.c:6082 netlink_rcv_skb+0x299/0x550 net/netlink/af_netlink.c:2540 rtnetlink_rcv+0x26/0x30 net/core/rtnetlink.c:6109 netlink_unicast_kernel net/netlink/af_netlink.c:1319 netlink_unicast+0x9ab/0xf50 net/netlink/af_netlink.c:1345 netlink_sendmsg+0xebc/0x10f0 net/netlink/af_netlink.c:1921 ... This patch ensures that the reserved field is always initialized.

In the Linux kernel 6.0.8, there is an out-of-bounds read in ntfs_attr_find in fs/ntfs/attrib.c.

In the Linux kernel, the following vulnerability has been resolved: crypto: arm64/poly1305 - fix a read out-of-bound A kasan error was reported during fuzzing: BUG: KASAN: slab-out-of-bounds in neon_poly1305_blocks.constprop.0+0x1b4/0x250 [poly1305_neon] Read of size 4 at addr ffff0010e293f010 by task syz-executor.5/1646715 CPU: 4 PID: 1646715 Comm: syz-executor.5 Kdump: loaded Not tainted 5.10.0.aarch64 #1 Hardware name: Huawei TaiShan 2280 /BC11SPCD, BIOS 1.59 01/31/2019 Call trace: dump_backtrace+0x0/0x394 show_stack+0x34/0x4c arch/arm64/kernel/stacktrace.c:196 __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x158/0x1e4 lib/dump_stack.c:118 print_address_description.constprop.0+0x68/0x204 mm/kasan/report.c:387 __kasan_report+0xe0/0x140 mm/kasan/report.c:547 kasan_report+0x44/0xe0 mm/kasan/report.c:564 check_memory_region_inline mm/kasan/generic.c:187 [inline] __asan_load4+0x94/0xd0 mm/kasan/generic.c:252 neon_poly1305_blocks.constprop.0+0x1b4/0x250 [poly1305_neon] neon_poly1305_do_update+0x6c/0x15c [poly1305_neon] neon_poly1305_update+0x9c/0x1c4 [poly1305_neon] crypto_shash_update crypto/shash.c:131 [inline] shash_finup_unaligned+0x84/0x15c crypto/shash.c:179 crypto_shash_finup+0x8c/0x140 crypto/shash.c:193 shash_digest_unaligned+0xb8/0xe4 crypto/shash.c:201 crypto_shash_digest+0xa4/0xfc crypto/shash.c:217 crypto_shash_tfm_digest+0xb4/0x150 crypto/shash.c:229 essiv_skcipher_setkey+0x164/0x200 [essiv] crypto_skcipher_setkey+0xb0/0x160 crypto/skcipher.c:612 skcipher_setkey+0x3c/0x50 crypto/algif_skcipher.c:305 alg_setkey+0x114/0x2a0 crypto/af_alg.c:220 alg_setsockopt+0x19c/0x210 crypto/af_alg.c:253 __sys_setsockopt+0x190/0x2e0 net/socket.c:2123 __do_sys_setsockopt net/socket.c:2134 [inline] __se_sys_setsockopt net/socket.c:2131 [inline] __arm64_sys_setsockopt+0x78/0x94 net/socket.c:2131 __invoke_syscall arch/arm64/kernel/syscall.c:36 [inline] invoke_syscall+0x64/0x100 arch/arm64/kernel/syscall.c:48 el0_svc_common.constprop.0+0x220/0x230 arch/arm64/kernel/syscall.c:155 do_el0_svc+0xb4/0xd4 arch/arm64/kernel/syscall.c:217 el0_svc+0x24/0x3c arch/arm64/kernel/entry-common.c:353 el0_sync_handler+0x160/0x164 arch/arm64/kernel/entry-common.c:369 el0_sync+0x160/0x180 arch/arm64/kernel/entry.S:683 This error can be reproduced by the following code compiled as ko on a system with kasan enabled: #include <linux/module.h> #include <linux/crypto.h> #include <crypto/hash.h> #include <crypto/poly1305.h> char test_data[] = "\x00\x01\x02\x03\x04\x05\x06\x07" "\x08\x09\x0a\x0b\x0c\x0d\x0e\x0f" "\x10\x11\x12\x13\x14\x15\x16\x17" "\x18\x19\x1a\x1b\x1c\x1d\x1e"; int init(void) { struct crypto_shash *tfm = NULL; char *data = NULL, *out = NULL; tfm = crypto_alloc_shash("poly1305", 0, 0); data = kmalloc(POLY1305_KEY_SIZE - 1, GFP_KERNEL); out = kmalloc(POLY1305_DIGEST_SIZE, GFP_KERNEL); memcpy(data, test_data, POLY1305_KEY_SIZE - 1); crypto_shash_tfm_digest(tfm, data, POLY1305_KEY_SIZE - 1, out); kfree(data); kfree(out); return 0; } void deinit(void) { } module_init(init) module_exit(deinit) MODULE_LICENSE("GPL"); The root cause of the bug sits in neon_poly1305_blocks. The logic neon_poly1305_blocks() performed is that if it was called with both s[] and r[] uninitialized, it will first try to initialize them with the data from the first "block" that it believed to be 32 bytes in length. First 16 bytes are used as the key and the next 16 bytes for s[]. This would lead to the aforementioned read out-of-bound. However, after calling poly1305_init_arch(), only 16 bytes were deducted from the input and s[] is initialized yet again with the following 16 bytes. The second initialization of s[] is certainly redundent which indicates that the first initialization should be for r[] only. This patch fixes the issue by calling poly1305_init_arm64() instead o ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: mtk_eth_soc: out of bounds read in mtk_hwlro_get_fdir_entry() The "fsp->location" variable comes from user via ethtool_get_rxnfc(). Check that it is valid to prevent an out of bounds read.