In the Linux kernel, the following vulnerability has been resolved: ixgbe: Fix NULL pointer dereference in ethtool loopback test The ixgbe driver currently generates a NULL pointer dereference when performing the ethtool loopback test. This is due to the fact that there isn't a q_vector associated with the test ring when it is setup as interrupts are not normally added to the test rings. To address this I have added code that will check for a q_vector before returning a napi_id value. If a q_vector is not present it will return a value of 0.

In the Linux kernel, the following vulnerability has been resolved: serial: max3100: Update uart_driver_registered on driver removal The removal of the last MAX3100 device triggers the removal of the driver. However, code doesn't update the respective global variable and after insmod — rmmod — insmod cycle the kernel oopses: max3100 spi-PRP0001:01: max3100_probe: adding port 0 BUG: kernel NULL pointer dereference, address: 0000000000000408 ... RIP: 0010:serial_core_register_port+0xa0/0x840 ... max3100_probe+0x1b6/0x280 [max3100] spi_probe+0x8d/0xb0 Update the actual state so next time UART driver will be registered again. Hugo also noticed, that the error path in the probe also affected by having the variable set, and not cleared. Instead of clearing it move the assignment after the successfull uart_register_driver() call.

In the Linux kernel, the following vulnerability has been resolved: drm: vc4: Fix possible null pointer dereference In vc4_hdmi_audio_init() of_get_address() may return NULL which is later dereferenced. Fix this bug by adding NULL check. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: libbpf: Prevent null-pointer dereference when prog to load has no BTF In bpf_objec_load_prog(), there's no guarantee that obj->btf is non-NULL when passing it to btf__fd(), and this function does not perform any check before dereferencing its argument (as bpf_object__btf_fd() used to do). As a consequence, we get segmentation fault errors in bpftool (for example) when trying to load programs that come without BTF information. v2: Keep btf__fd() in the fix instead of reverting to bpf_object__btf_fd().

In the Linux kernel, the following vulnerability has been resolved: cpufreq: exit() callback is optional The exit() callback is optional and shouldn't be called without checking a valid pointer first. Also, we must clear freq_table pointer even if the exit() callback isn't present.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Check 'folio' pointer for NULL It can be NULL if bmap is called.

In the Linux kernel, the following vulnerability has been resolved: net: ti: icssg_prueth: Fix NULL pointer dereference in prueth_probe() In the prueth_probe() function, if one of the calls to emac_phy_connect() fails due to of_phy_connect() returning NULL, then the subsequent call to phy_attached_info() will dereference a NULL pointer. Check the return code of emac_phy_connect and fail cleanly if there is an error.

In the Linux kernel, the following vulnerability has been resolved: drm/msm/a6xx: Avoid a nullptr dereference when speedbin setting fails Calling a6xx_destroy() before adreno_gpu_init() leads to a null pointer dereference on: msm_gpu_cleanup() : platform_set_drvdata(gpu->pdev, NULL); as gpu->pdev is only assigned in: a6xx_gpu_init() |_ adreno_gpu_init |_ msm_gpu_init() Instead of relying on handwavy null checks down the cleanup chain, explicitly de-allocate the LLC data and free a6xx_gpu instead. Patchwork: https://patchwork.freedesktop.org/patch/588919/

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: Fix dereference of null pointer flow In the case where chain->flags & NFT_CHAIN_HW_OFFLOAD is false then nft_flow_rule_create is not called and flow is NULL. The subsequent error handling execution via label err_destroy_flow_rule will lead to a null pointer dereference on flow when calling nft_flow_rule_destroy. Since the error path to err_destroy_flow_rule has to cater for null and non-null flows, only call nft_flow_rule_destroy if flow is non-null to fix this issue. Addresses-Coverity: ("Explicity null dereference")

In the Linux kernel, the following vulnerability has been resolved: can: mcp251x: fix resume from sleep before interface was brought up Since 8ce8c0abcba3 the driver queues work via priv->restart_work when resuming after suspend, even when the interface was not previously enabled. This causes a null dereference error as the workqueue is only allocated and initialized in mcp251x_open(). To fix this we move the workqueue init to mcp251x_can_probe() as there is no reason to do it later and repeat it whenever mcp251x_open() is called. [mkl: fix error handling in mcp251x_stop()]

In the Linux kernel, the following vulnerability has been resolved: PCI: endpoint: Fix NULL pointer dereference for ->get_features() get_features ops of pci_epc_ops may return NULL, causing NULL pointer dereference in pci_epf_test_alloc_space function. Let us add a check for pci_epc_feature pointer in pci_epf_test_bind before we access it to avoid any such NULL pointer dereference and return -ENOTSUPP in case pci_epc_feature is not found. When the patch is not applied and EPC features is not implemented in the platform driver, we see the following dump due to kernel NULL pointer dereference. Call trace: pci_epf_test_bind+0xf4/0x388 pci_epf_bind+0x3c/0x80 pci_epc_epf_link+0xa8/0xcc configfs_symlink+0x1a4/0x48c vfs_symlink+0x104/0x184 do_symlinkat+0x80/0xd4 __arm64_sys_symlinkat+0x1c/0x24 el0_svc_common.constprop.3+0xb8/0x170 el0_svc_handler+0x70/0x88 el0_svc+0x8/0x640 Code: d2800581 b9403ab9 f9404ebb 8b394f60 (f9400400) ---[ end trace a438e3c5a24f9df0 ]---

In the Linux kernel, the following vulnerability has been resolved: mm/secretmem: fix NULL page->mapping dereference in page_is_secretmem() Check for a NULL page->mapping before dereferencing the mapping in page_is_secretmem(), as the page's mapping can be nullified while gup() is running, e.g. by reclaim or truncation. BUG: kernel NULL pointer dereference, address: 0000000000000068 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 6 PID: 4173897 Comm: CPU 3/KVM Tainted: G W RIP: 0010:internal_get_user_pages_fast+0x621/0x9d0 Code: <48> 81 7a 68 80 08 04 bc 0f 85 21 ff ff 8 89 c7 be RSP: 0018:ffffaa90087679b0 EFLAGS: 00010046 RAX: ffffe3f37905b900 RBX: 00007f2dd561e000 RCX: ffffe3f37905b934 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffe3f37905b900 ... CR2: 0000000000000068 CR3: 00000004c5898003 CR4: 00000000001726e0 Call Trace: get_user_pages_fast_only+0x13/0x20 hva_to_pfn+0xa9/0x3e0 try_async_pf+0xa1/0x270 direct_page_fault+0x113/0xad0 kvm_mmu_page_fault+0x69/0x680 vmx_handle_exit+0xe1/0x5d0 kvm_arch_vcpu_ioctl_run+0xd81/0x1c70 kvm_vcpu_ioctl+0x267/0x670 __x64_sys_ioctl+0x83/0xa0 do_syscall_64+0x56/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: HCI: Fix potential null-ptr-deref Fix potential null-ptr-deref in hci_le_big_sync_established_evt().

In the Linux kernel, the following vulnerability has been resolved: s390/bpf: Fix bpf_plt pointer arithmetic Kui-Feng Lee reported a crash on s390x triggered by the dummy_st_ops/dummy_init_ptr_arg test [1]: [<0000000000000002>] 0x2 [<00000000009d5cde>] bpf_struct_ops_test_run+0x156/0x250 [<000000000033145a>] __sys_bpf+0xa1a/0xd00 [<00000000003319dc>] __s390x_sys_bpf+0x44/0x50 [<0000000000c4382c>] __do_syscall+0x244/0x300 [<0000000000c59a40>] system_call+0x70/0x98 This is caused by GCC moving memcpy() after assignments in bpf_jit_plt(), resulting in NULL pointers being written instead of the return and the target addresses. Looking at the GCC internals, the reordering is allowed because the alias analysis thinks that the memcpy() destination and the assignments' left-hand-sides are based on different objects: new_plt and bpf_plt_ret/bpf_plt_target respectively, and therefore they cannot alias. This is in turn due to a violation of the C standard: When two pointers are subtracted, both shall point to elements of the same array object, or one past the last element of the array object ... From the C's perspective, bpf_plt_ret and bpf_plt are distinct objects and cannot be subtracted. In the practical terms, doing so confuses the GCC's alias analysis. The code was written this way in order to let the C side know a few offsets defined in the assembly. While nice, this is by no means necessary. Fix the noncompliance by hardcoding these offsets. [1] https://lore.kernel.org/bpf/c9923c1d-971d-4022-8dc8-1364e929d34c@gmail.com/

In the Linux kernel, the following vulnerability has been resolved: net: dsa: microchip: Added the condition for scheduling ksz_mib_read_work When the ksz module is installed and removed using rmmod, kernel crashes with null pointer dereferrence error. During rmmod, ksz_switch_remove function tries to cancel the mib_read_workqueue using cancel_delayed_work_sync routine and unregister switch from dsa. During dsa_unregister_switch it calls ksz_mac_link_down, which in turn reschedules the workqueue since mib_interval is non-zero. Due to which queue executed after mib_interval and it tries to access dp->slave. But the slave is unregistered in the ksz_switch_remove function. Hence kernel crashes. To avoid this crash, before canceling the workqueue, resetted the mib_interval to 0. v1 -> v2: -Removed the if condition in ksz_mib_read_work

In the Linux kernel, the following vulnerability has been resolved: ipv4: check for NULL idev in ip_route_use_hint() syzbot was able to trigger a NULL deref in fib_validate_source() in an old tree [1]. It appears the bug exists in latest trees. All calls to __in_dev_get_rcu() must be checked for a NULL result. [1] general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] CPU: 2 PID: 3257 Comm: syz-executor.3 Not tainted 5.10.0-syzkaller #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 RIP: 0010:fib_validate_source+0xbf/0x15a0 net/ipv4/fib_frontend.c:425 Code: 18 f2 f2 f2 f2 42 c7 44 20 23 f3 f3 f3 f3 48 89 44 24 78 42 c6 44 20 27 f3 e8 5d 88 48 fc 4c 89 e8 48 c1 e8 03 48 89 44 24 18 <42> 80 3c 20 00 74 08 4c 89 ef e8 d2 15 98 fc 48 89 5c 24 10 41 bf RSP: 0018:ffffc900015fee40 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff88800f7a4000 RCX: ffff88800f4f90c0 RDX: 0000000000000000 RSI: 0000000004001eac RDI: ffff8880160c64c0 RBP: ffffc900015ff060 R08: 0000000000000000 R09: ffff88800f7a4000 R10: 0000000000000002 R11: ffff88800f4f90c0 R12: dffffc0000000000 R13: 0000000000000000 R14: 0000000000000000 R15: ffff88800f7a4000 FS: 00007f938acfe6c0(0000) GS:ffff888058c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f938acddd58 CR3: 000000001248e000 CR4: 0000000000352ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: ip_route_use_hint+0x410/0x9b0 net/ipv4/route.c:2231 ip_rcv_finish_core+0x2c4/0x1a30 net/ipv4/ip_input.c:327 ip_list_rcv_finish net/ipv4/ip_input.c:612 [inline] ip_sublist_rcv+0x3ed/0xe50 net/ipv4/ip_input.c:638 ip_list_rcv+0x422/0x470 net/ipv4/ip_input.c:673 __netif_receive_skb_list_ptype net/core/dev.c:5572 [inline] __netif_receive_skb_list_core+0x6b1/0x890 net/core/dev.c:5620 __netif_receive_skb_list net/core/dev.c:5672 [inline] netif_receive_skb_list_internal+0x9f9/0xdc0 net/core/dev.c:5764 netif_receive_skb_list+0x55/0x3e0 net/core/dev.c:5816 xdp_recv_frames net/bpf/test_run.c:257 [inline] xdp_test_run_batch net/bpf/test_run.c:335 [inline] bpf_test_run_xdp_live+0x1818/0x1d00 net/bpf/test_run.c:363 bpf_prog_test_run_xdp+0x81f/0x1170 net/bpf/test_run.c:1376 bpf_prog_test_run+0x349/0x3c0 kernel/bpf/syscall.c:3736 __sys_bpf+0x45c/0x710 kernel/bpf/syscall.c:5115 __do_sys_bpf kernel/bpf/syscall.c:5201 [inline] __se_sys_bpf kernel/bpf/syscall.c:5199 [inline] __x64_sys_bpf+0x7c/0x90 kernel/bpf/syscall.c:5199

In the Linux kernel, the following vulnerability has been resolved: xdp: use flags field to disambiguate broadcast redirect When redirecting a packet using XDP, the bpf_redirect_map() helper will set up the redirect destination information in struct bpf_redirect_info (using the __bpf_xdp_redirect_map() helper function), and the xdp_do_redirect() function will read this information after the XDP program returns and pass the frame on to the right redirect destination. When using the BPF_F_BROADCAST flag to do multicast redirect to a whole map, __bpf_xdp_redirect_map() sets the 'map' pointer in struct bpf_redirect_info to point to the destination map to be broadcast. And xdp_do_redirect() reacts to the value of this map pointer to decide whether it's dealing with a broadcast or a single-value redirect. However, if the destination map is being destroyed before xdp_do_redirect() is called, the map pointer will be cleared out (by bpf_clear_redirect_map()) without waiting for any XDP programs to stop running. This causes xdp_do_redirect() to think that the redirect was to a single target, but the target pointer is also NULL (since broadcast redirects don't have a single target), so this causes a crash when a NULL pointer is passed to dev_map_enqueue(). To fix this, change xdp_do_redirect() to react directly to the presence of the BPF_F_BROADCAST flag in the 'flags' value in struct bpf_redirect_info to disambiguate between a single-target and a broadcast redirect. And only read the 'map' pointer if the broadcast flag is set, aborting if that has been cleared out in the meantime. This prevents the crash, while keeping the atomic (cmpxchg-based) clearing of the map pointer itself, and without adding any more checks in the non-broadcast fast path.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Use mlx5_ipsec_rx_status_destroy to correctly delete status rules rx_create no longer allocates a modify_hdr instance that needs to be cleaned up. The mlx5_modify_header_dealloc call will lead to a NULL pointer dereference. A leak in the rules also previously occurred since there are now two rules populated related to status. BUG: kernel NULL pointer dereference, address: 0000000000000000 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 109907067 P4D 109907067 PUD 116890067 PMD 0 Oops: 0000 [#1] SMP CPU: 1 PID: 484 Comm: ip Not tainted 6.9.0-rc2-rrameshbabu+ #254 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS Arch Linux 1.16.3-1-1 04/01/2014 RIP: 0010:mlx5_modify_header_dealloc+0xd/0x70 <snip> Call Trace: <TASK> ? show_regs+0x60/0x70 ? __die+0x24/0x70 ? page_fault_oops+0x15f/0x430 ? free_to_partial_list.constprop.0+0x79/0x150 ? do_user_addr_fault+0x2c9/0x5c0 ? exc_page_fault+0x63/0x110 ? asm_exc_page_fault+0x27/0x30 ? mlx5_modify_header_dealloc+0xd/0x70 rx_create+0x374/0x590 rx_add_rule+0x3ad/0x500 ? rx_add_rule+0x3ad/0x500 ? mlx5_cmd_exec+0x2c/0x40 ? mlx5_create_ipsec_obj+0xd6/0x200 mlx5e_accel_ipsec_fs_add_rule+0x31/0xf0 mlx5e_xfrm_add_state+0x426/0xc00 <snip>

In the Linux kernel, the following vulnerability has been resolved: powerpc/pseries/iommu: LPAR panics during boot up with a frozen PE At the time of LPAR boot up, partition firmware provides Open Firmware property ibm,dma-window for the PE. This property is provided on the PCI bus the PE is attached to. There are execptions where the partition firmware might not provide this property for the PE at the time of LPAR boot up. One of the scenario is where the firmware has frozen the PE due to some error condition. This PE is frozen for 24 hours or unless the whole system is reinitialized. Within this time frame, if the LPAR is booted, the frozen PE will be presented to the LPAR but ibm,dma-window property could be missing. Today, under these circumstances, the LPAR oopses with NULL pointer dereference, when configuring the PCI bus the PE is attached to. BUG: Kernel NULL pointer dereference on read at 0x000000c8 Faulting instruction address: 0xc0000000001024c0 Oops: Kernel access of bad area, sig: 7 [#1] LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries Modules linked in: Supported: Yes CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.4.0-150600.9-default #1 Hardware name: IBM,9043-MRX POWER10 (raw) 0x800200 0xf000006 of:IBM,FW1060.00 (NM1060_023) hv:phyp pSeries NIP: c0000000001024c0 LR: c0000000001024b0 CTR: c000000000102450 REGS: c0000000037db5c0 TRAP: 0300 Not tainted (6.4.0-150600.9-default) MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 28000822 XER: 00000000 CFAR: c00000000010254c DAR: 00000000000000c8 DSISR: 00080000 IRQMASK: 0 ... NIP [c0000000001024c0] pci_dma_bus_setup_pSeriesLP+0x70/0x2a0 LR [c0000000001024b0] pci_dma_bus_setup_pSeriesLP+0x60/0x2a0 Call Trace: pci_dma_bus_setup_pSeriesLP+0x60/0x2a0 (unreliable) pcibios_setup_bus_self+0x1c0/0x370 __of_scan_bus+0x2f8/0x330 pcibios_scan_phb+0x280/0x3d0 pcibios_init+0x88/0x12c do_one_initcall+0x60/0x320 kernel_init_freeable+0x344/0x3e4 kernel_init+0x34/0x1d0 ret_from_kernel_user_thread+0x14/0x1c

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Atom Integrated System Info v2_2 for DCN35 New request from KMD/VBIOS in order to support new UMA carveout model. This fixes a null dereference from accessing Ctx->dc_bios->integrated_info while it was NULL. DAL parses through the BIOS and extracts the necessary integrated_info but was missing a case for the new BIOS version 2.3.

In the Linux kernel, the following vulnerability has been resolved: swiotlb: initialise restricted pool list_head when SWIOTLB_DYNAMIC=y Using restricted DMA pools (CONFIG_DMA_RESTRICTED_POOL=y) in conjunction with dynamic SWIOTLB (CONFIG_SWIOTLB_DYNAMIC=y) leads to the following crash when initialising the restricted pools at boot-time: | Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008 | Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP | pc : rmem_swiotlb_device_init+0xfc/0x1ec | lr : rmem_swiotlb_device_init+0xf0/0x1ec | Call trace: | rmem_swiotlb_device_init+0xfc/0x1ec | of_reserved_mem_device_init_by_idx+0x18c/0x238 | of_dma_configure_id+0x31c/0x33c | platform_dma_configure+0x34/0x80 faddr2line reveals that the crash is in the list validation code: include/linux/list.h:83 include/linux/rculist.h:79 include/linux/rculist.h:106 kernel/dma/swiotlb.c:306 kernel/dma/swiotlb.c:1695 because add_mem_pool() is trying to list_add_rcu() to a NULL 'mem->pools'. Fix the crash by initialising the 'mem->pools' list_head in rmem_swiotlb_device_init() before calling add_mem_pool().

In the Linux kernel, the following vulnerability has been resolved: i2c: smbus: fix NULL function pointer dereference Baruch reported an OOPS when using the designware controller as target only. Target-only modes break the assumption of one transfer function always being available. Fix this by always checking the pointer in __i2c_transfer. [wsa: dropped the simplification in core-smbus to avoid theoretical regressions]

In the Linux kernel, the following vulnerability has been resolved: nfsd: fix NULL dereference in nfs3svc_encode_getaclres In error cases the dentry may be NULL. Before 20798dfe249a, the encoder also checked dentry and d_really_is_positive(dentry), but that looks like overkill to me--zero status should be enough to guarantee a positive dentry. This isn't the first time we've seen an error-case NULL dereference hidden in the initialization of a local variable in an xdr encoder. But I went back through the other recent rewrites and didn't spot any similar bugs.

In the Linux kernel, the following vulnerability has been resolved: pmdomain: ti: Add a null pointer check to the omap_prm_domain_init devm_kasprintf() returns a pointer to dynamically allocated memory which can be NULL upon failure. Ensure the allocation was successful by checking the pointer validity.

In the Linux kernel, the following vulnerability has been resolved: net/rds: fix possible cp null dereference cp might be null, calling cp->cp_conn would produce null dereference [Simon Horman adds:] Analysis: * cp is a parameter of __rds_rdma_map and is not reassigned. * The following call-sites pass a NULL cp argument to __rds_rdma_map() - rds_get_mr() - rds_get_mr_for_dest * Prior to the code above, the following assumes that cp may be NULL (which is indicative, but could itself be unnecessary) trans_private = rs->rs_transport->get_mr( sg, nents, rs, &mr->r_key, cp ? cp->cp_conn : NULL, args->vec.addr, args->vec.bytes, need_odp ? ODP_ZEROBASED : ODP_NOT_NEEDED); * The code modified by this patch is guarded by IS_ERR(trans_private), where trans_private is assigned as per the previous point in this analysis. The only implementation of get_mr that I could locate is rds_ib_get_mr() which can return an ERR_PTR if the conn (4th) argument is NULL. * ret is set to PTR_ERR(trans_private). rds_ib_get_mr can return ERR_PTR(-ENODEV) if the conn (4th) argument is NULL. Thus ret may be -ENODEV in which case the code in question will execute. Conclusion: * cp may be NULL at the point where this patch adds a check; this patch does seem to address a possible bug

In the Linux kernel, the following vulnerability has been resolved: tls: fix missing memory barrier in tls_init In tls_init(), a write memory barrier is missing, and store-store reordering may cause NULL dereference in tls_{setsockopt,getsockopt}. CPU0 CPU1 ----- ----- // In tls_init() // In tls_ctx_create() ctx = kzalloc() ctx->sk_proto = READ_ONCE(sk->sk_prot) -(1) // In update_sk_prot() WRITE_ONCE(sk->sk_prot, tls_prots) -(2) // In sock_common_setsockopt() READ_ONCE(sk->sk_prot)->setsockopt() // In tls_{setsockopt,getsockopt}() ctx->sk_proto->setsockopt() -(3) In the above scenario, when (1) and (2) are reordered, (3) can observe the NULL value of ctx->sk_proto, causing NULL dereference. To fix it, we rely on rcu_assign_pointer() which implies the release barrier semantic. By moving rcu_assign_pointer() after ctx->sk_proto is initialized, we can ensure that ctx->sk_proto are visible when changing sk->sk_prot.

In the Linux kernel, the following vulnerability has been resolved: drm/arm/malidp: fix a possible null pointer dereference In malidp_mw_connector_reset, new memory is allocated with kzalloc, but no check is performed. In order to prevent null pointer dereferencing, ensure that mw_state is checked before calling __drm_atomic_helper_connector_reset.

In the Linux kernel, the following vulnerability has been resolved: netfilter: tproxy: bail out if IP has been disabled on the device syzbot reports: general protection fault, probably for non-canonical address 0xdffffc0000000003: 0000 [#1] PREEMPT SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f] [..] RIP: 0010:nf_tproxy_laddr4+0xb7/0x340 net/ipv4/netfilter/nf_tproxy_ipv4.c:62 Call Trace: nft_tproxy_eval_v4 net/netfilter/nft_tproxy.c:56 [inline] nft_tproxy_eval+0xa9a/0x1a00 net/netfilter/nft_tproxy.c:168 __in_dev_get_rcu() can return NULL, so check for this.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btintel: Fix null ptr deref in btintel_read_version If hci_cmd_sync_complete() is triggered and skb is NULL, then hdev->req_skb is NULL, which will cause this issue.

In the Linux kernel, the following vulnerability has been resolved: mlxbf_gige: call request_irq() after NAPI initialized The mlxbf_gige driver encounters a NULL pointer exception in mlxbf_gige_open() when kdump is enabled. The sequence to reproduce the exception is as follows: a) enable kdump b) trigger kdump via "echo c > /proc/sysrq-trigger" c) kdump kernel executes d) kdump kernel loads mlxbf_gige module e) the mlxbf_gige module runs its open() as the the "oob_net0" interface is brought up f) mlxbf_gige module will experience an exception during its open(), something like: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000086000004 EC = 0x21: IABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault user pgtable: 4k pages, 48-bit VAs, pgdp=00000000e29a4000 [0000000000000000] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000086000004 [#1] SMP CPU: 0 PID: 812 Comm: NetworkManager Tainted: G OE 5.15.0-1035-bluefield #37-Ubuntu Hardware name: https://www.mellanox.com BlueField-3 SmartNIC Main Card/BlueField-3 SmartNIC Main Card, BIOS 4.6.0.13024 Jan 19 2024 pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : 0x0 lr : __napi_poll+0x40/0x230 sp : ffff800008003e00 x29: ffff800008003e00 x28: 0000000000000000 x27: 00000000ffffffff x26: ffff000066027238 x25: ffff00007cedec00 x24: ffff800008003ec8 x23: 000000000000012c x22: ffff800008003eb7 x21: 0000000000000000 x20: 0000000000000001 x19: ffff000066027238 x18: 0000000000000000 x17: ffff578fcb450000 x16: ffffa870b083c7c0 x15: 0000aaab010441d0 x14: 0000000000000001 x13: 00726f7272655f65 x12: 6769675f6662786c x11: 0000000000000000 x10: 0000000000000000 x9 : ffffa870b0842398 x8 : 0000000000000004 x7 : fe5a48b9069706ea x6 : 17fdb11fc84ae0d2 x5 : d94a82549d594f35 x4 : 0000000000000000 x3 : 0000000000400100 x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000066027238 Call trace: 0x0 net_rx_action+0x178/0x360 __do_softirq+0x15c/0x428 __irq_exit_rcu+0xac/0xec irq_exit+0x18/0x2c handle_domain_irq+0x6c/0xa0 gic_handle_irq+0xec/0x1b0 call_on_irq_stack+0x20/0x2c do_interrupt_handler+0x5c/0x70 el1_interrupt+0x30/0x50 el1h_64_irq_handler+0x18/0x2c el1h_64_irq+0x7c/0x80 __setup_irq+0x4c0/0x950 request_threaded_irq+0xf4/0x1bc mlxbf_gige_request_irqs+0x68/0x110 [mlxbf_gige] mlxbf_gige_open+0x5c/0x170 [mlxbf_gige] __dev_open+0x100/0x220 __dev_change_flags+0x16c/0x1f0 dev_change_flags+0x2c/0x70 do_setlink+0x220/0xa40 __rtnl_newlink+0x56c/0x8a0 rtnl_newlink+0x58/0x84 rtnetlink_rcv_msg+0x138/0x3c4 netlink_rcv_skb+0x64/0x130 rtnetlink_rcv+0x20/0x30 netlink_unicast+0x2ec/0x360 netlink_sendmsg+0x278/0x490 __sock_sendmsg+0x5c/0x6c ____sys_sendmsg+0x290/0x2d4 ___sys_sendmsg+0x84/0xd0 __sys_sendmsg+0x70/0xd0 __arm64_sys_sendmsg+0x2c/0x40 invoke_syscall+0x78/0x100 el0_svc_common.constprop.0+0x54/0x184 do_el0_svc+0x30/0xac el0_svc+0x48/0x160 el0t_64_sync_handler+0xa4/0x12c el0t_64_sync+0x1a4/0x1a8 Code: bad PC value ---[ end trace 7d1c3f3bf9d81885 ]--- Kernel panic - not syncing: Oops: Fatal exception in interrupt Kernel Offset: 0x2870a7a00000 from 0xffff800008000000 PHYS_OFFSET: 0x80000000 CPU features: 0x0,000005c1,a3332a5a Memory Limit: none ---[ end Kernel panic - not syncing: Oops: Fatal exception in interrupt ]--- The exception happens because there is a pending RX interrupt before the call to request_irq(RX IRQ) executes. Then, the RX IRQ handler fires immediately after this request_irq() completes. The ---truncated---

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: fix null pointer access when abort scan During cancel scan we might use vif that weren't scanning. Fix this by using the actual scanning vif.

In the Linux kernel, the following vulnerability has been resolved: net: phy: phy_device: Prevent nullptr exceptions on ISR If phydev->irq is set unconditionally, check for valid interrupt handler or fall back to polling mode to prevent nullptr exceptions in interrupt service routine.

In the Linux kernel, the following vulnerability has been resolved: net: ll_temac: platform_get_resource replaced by wrong function The function platform_get_resource was replaced with devm_platform_ioremap_resource_byname and is called using 0 as name. This eventually ends up in platform_get_resource_byname in the call stack, where it causes a null pointer in strcmp. if (type == resource_type(r) && !strcmp(r->name, name)) It should have been replaced with devm_platform_ioremap_resource.

In the Linux kernel, the following vulnerability has been resolved: drivers: perf: ctr_get_width function for legacy is not defined With parameters CONFIG_RISCV_PMU_LEGACY=y and CONFIG_RISCV_PMU_SBI=n linux kernel crashes when you try perf record: $ perf record ls [ 46.749286] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 46.750199] Oops [#1] [ 46.750342] Modules linked in: [ 46.750608] CPU: 0 PID: 107 Comm: perf-exec Not tainted 6.6.0 #2 [ 46.750906] Hardware name: riscv-virtio,qemu (DT) [ 46.751184] epc : 0x0 [ 46.751430] ra : arch_perf_update_userpage+0x54/0x13e [ 46.751680] epc : 0000000000000000 ra : ffffffff8072ee52 sp : ff2000000022b8f0 [ 46.751958] gp : ffffffff81505988 tp : ff6000000290d400 t0 : ff2000000022b9c0 [ 46.752229] t1 : 0000000000000001 t2 : 0000000000000003 s0 : ff2000000022b930 [ 46.752451] s1 : ff600000028fb000 a0 : 0000000000000000 a1 : ff600000028fb000 [ 46.752673] a2 : 0000000ae2751268 a3 : 00000000004fb708 a4 : 0000000000000004 [ 46.752895] a5 : 0000000000000000 a6 : 000000000017ffe3 a7 : 00000000000000d2 [ 46.753117] s2 : ff600000028fb000 s3 : 0000000ae2751268 s4 : 0000000000000000 [ 46.753338] s5 : ffffffff8153e290 s6 : ff600000863b9000 s7 : ff60000002961078 [ 46.753562] s8 : ff60000002961048 s9 : ff60000002961058 s10: 0000000000000001 [ 46.753783] s11: 0000000000000018 t3 : ffffffffffffffff t4 : ffffffffffffffff [ 46.754005] t5 : ff6000000292270c t6 : ff2000000022bb30 [ 46.754179] status: 0000000200000100 badaddr: 0000000000000000 cause: 000000000000000c [ 46.754653] Code: Unable to access instruction at 0xffffffffffffffec. [ 46.754939] ---[ end trace 0000000000000000 ]--- [ 46.755131] note: perf-exec[107] exited with irqs disabled [ 46.755546] note: perf-exec[107] exited with preempt_count 4 This happens because in the legacy case the ctr_get_width function was not defined, but it is used in arch_perf_update_userpage. Also remove extra check in riscv_pmu_ctr_get_width_mask

In the Linux kernel, the following vulnerability has been resolved: aio: Fix null ptr deref in aio_complete() wakeup list_del_init_careful() needs to be the last access to the wait queue entry - it effectively unlocks access. Previously, finish_wait() would see the empty list head and skip taking the lock, and then we'd return - but the completion path would still attempt to do the wakeup after the task_struct pointer had been overwritten.

In the Linux kernel, the following vulnerability has been resolved: net: phy: micrel: Fix potential null pointer dereference In lan8814_get_sig_rx() and lan8814_get_sig_tx() ptp_parse_header() may return NULL as ptp_header due to abnormal packet type or corrupted packet. Fix this bug by adding ptp_header check. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: qca: fix NULL-deref on non-serdev suspend Qualcomm ROME controllers can be registered from the Bluetooth line discipline and in this case the HCI UART serdev pointer is NULL. Add the missing sanity check to prevent a NULL-pointer dereference when wakeup() is called for a non-serdev controller during suspend. Just return true for now to restore the original behaviour and address the crash with pre-6.2 kernels, which do not have commit e9b3e5b8c657 ("Bluetooth: hci_qca: only assign wakeup with serial port support") that causes the crash to happen already at setup() time.

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix null pointer dereference in lpfc_prep_els_iocb() It is possible to call lpfc_issue_els_plogi() passing a did for which no matching ndlp is found. A call is then made to lpfc_prep_els_iocb() with a null pointer to a lpfc_nodelist structure resulting in a null pointer dereference. Fix by returning an error status if no valid ndlp is found. Fix up comments regarding ndlp reference counting.

In the Linux kernel, the following vulnerability has been resolved: ACPI: fix NULL pointer dereference Commit 71f642833284 ("ACPI: utils: Fix reference counting in for_each_acpi_dev_match()") started doing "acpi_dev_put()" on a pointer that was possibly NULL. That fails miserably, because that helper inline function is not set up to handle that case. Just make acpi_dev_put() silently accept a NULL pointer, rather than calling down to put_device() with an invalid offset off that NULL pointer.

In the Linux kernel, the following vulnerability has been resolved: iommu/s390: Implement blocking domain This fixes a crash when surprise hot-unplugging a PCI device. This crash happens because during hot-unplug __iommu_group_set_domain_nofail() attaching the default domain fails when the platform no longer recognizes the device as it has already been removed and we end up with a NULL domain pointer and UAF. This is exactly the case referred to in the second comment in __iommu_device_set_domain() and just as stated there if we can instead attach the blocking domain the UAF is prevented as this can handle the already removed device. Implement the blocking domain to use this handling. With this change, the crash is fixed but we still hit a warning attempting to change DMA ownership on a blocked device.

In the Linux kernel, the following vulnerability has been resolved: virtio_pci: Fix admin vq cleanup by using correct info pointer vp_modern_avq_cleanup() and vp_del_vqs() clean up admin vq resources by virtio_pci_vq_info pointer. The info pointer of admin vq is stored in vp_dev->admin_vq.info instead of vp_dev->vqs[]. Using the info pointer from vp_dev->vqs[] for admin vq causes a kernel NULL pointer dereference bug. In vp_modern_avq_cleanup() and vp_del_vqs(), get the info pointer from vp_dev->admin_vq.info for admin vq to clean up the resources. Also make info ptr as argument of vp_del_vq() to be symmetric with vp_setup_vq(). vp_reset calls vp_modern_avq_cleanup, and causes the Call Trace: ================================================================== BUG: kernel NULL pointer dereference, address:0000000000000000 ... CPU: 49 UID: 0 PID: 4439 Comm: modprobe Not tainted 6.11.0-rc5 #1 RIP: 0010:vp_reset+0x57/0x90 [virtio_pci] Call Trace: <TASK> ... ? vp_reset+0x57/0x90 [virtio_pci] ? vp_reset+0x38/0x90 [virtio_pci] virtio_reset_device+0x1d/0x30 remove_vq_common+0x1c/0x1a0 [virtio_net] virtnet_remove+0xa1/0xc0 [virtio_net] virtio_dev_remove+0x46/0xa0 ... virtio_pci_driver_exit+0x14/0x810 [virtio_pci] ==================================================================

In the Linux kernel, the following vulnerability has been resolved: serial: rp2: use 'request_firmware' instead of 'request_firmware_nowait' In 'rp2_probe', the driver registers 'rp2_uart_interrupt' then calls 'rp2_fw_cb' through 'request_firmware_nowait'. In 'rp2_fw_cb', if the firmware don't exists, function just return without initializing ports of 'rp2_card'. But now the interrupt handler function has been registered, and when an interrupt comes, 'rp2_uart_interrupt' may access those ports then causing NULL pointer dereference or other bugs. Because the driver does some initialization work in 'rp2_fw_cb', in order to make the driver ready to handle interrupts, 'request_firmware' should be used instead of asynchronous 'request_firmware_nowait'. This report reveals it: INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.19.177-gdba4159c14ef-dirty #45 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59- gc9ba5276e321-prebuilt.qemu.org 04/01/2014 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xec/0x156 lib/dump_stack.c:118 assign_lock_key kernel/locking/lockdep.c:727 [inline] register_lock_class+0x14e5/0x1ba0 kernel/locking/lockdep.c:753 __lock_acquire+0x187/0x3750 kernel/locking/lockdep.c:3303 lock_acquire+0x124/0x340 kernel/locking/lockdep.c:3907 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x32/0x50 kernel/locking/spinlock.c:144 spin_lock include/linux/spinlock.h:329 [inline] rp2_ch_interrupt drivers/tty/serial/rp2.c:466 [inline] rp2_asic_interrupt.isra.9+0x15d/0x990 drivers/tty/serial/rp2.c:493 rp2_uart_interrupt+0x49/0xe0 drivers/tty/serial/rp2.c:504 __handle_irq_event_percpu+0xfb/0x770 kernel/irq/handle.c:149 handle_irq_event_percpu+0x79/0x150 kernel/irq/handle.c:189 handle_irq_event+0xac/0x140 kernel/irq/handle.c:206 handle_fasteoi_irq+0x232/0x5c0 kernel/irq/chip.c:725 generic_handle_irq_desc include/linux/irqdesc.h:155 [inline] handle_irq+0x230/0x3a0 arch/x86/kernel/irq_64.c:87 do_IRQ+0xa7/0x1e0 arch/x86/kernel/irq.c:247 common_interrupt+0xf/0xf arch/x86/entry/entry_64.S:670 </IRQ> RIP: 0010:native_safe_halt+0x28/0x30 arch/x86/include/asm/irqflags.h:61 Code: 00 00 55 be 04 00 00 00 48 c7 c7 00 c2 2f 8c 48 89 e5 e8 fb 31 e7 f8 8b 05 75 af 8d 03 85 c0 7e 07 0f 00 2d 8a 61 65 00 fb f4 <5d> c3 90 90 90 90 90 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41 RSP: 0018:ffff88806b71fcc8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffde RAX: 0000000000000000 RBX: ffffffff8bde7e48 RCX: ffffffff88a21285 RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff8c2fc200 RBP: ffff88806b71fcc8 R08: fffffbfff185f840 R09: fffffbfff185f840 R10: 0000000000000001 R11: fffffbfff185f840 R12: 0000000000000002 R13: ffffffff8bea18a0 R14: 0000000000000000 R15: 0000000000000000 arch_safe_halt arch/x86/include/asm/paravirt.h:94 [inline] default_idle+0x6f/0x360 arch/x86/kernel/process.c:557 arch_cpu_idle+0xf/0x20 arch/x86/kernel/process.c:548 default_idle_call+0x3b/0x60 kernel/sched/idle.c:93 cpuidle_idle_call kernel/sched/idle.c:153 [inline] do_idle+0x2ab/0x3c0 kernel/sched/idle.c:263 cpu_startup_entry+0xcb/0xe0 kernel/sched/idle.c:369 start_secondary+0x3b8/0x4e0 arch/x86/kernel/smpboot.c:271 secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:243 BUG: unable to handle kernel NULL pointer dereference at 0000000000000010 PGD 8000000056d27067 P4D 8000000056d27067 PUD 56d28067 PMD 0 Oops: 0000 [#1] PREEMPT SMP KASAN PTI CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.19.177-gdba4159c14ef-dirty #45 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59- gc9ba5276e321-prebuilt.qemu.org 04/01/2014 RIP: 0010:readl arch/x86/include/asm/io.h:59 [inline] RIP: 0010:rp2_ch_interrupt drivers/tty/serial/rp2.c:472 [inline] RIP: 0010:rp2_asic_interrupt.isra.9+0x181/0x990 drivers/tty/serial/rp2.c: 493 Co ---truncated---

A flaw was found in the Linux kernel’s IP framework for transforming packets (XFRM subsystem). This issue may allow a malicious user with CAP_NET_ADMIN privileges to directly dereference a NULL pointer in xfrm_update_ae_params(), leading to a possible kernel crash and denial of service.

In the Linux kernel, the following vulnerability has been resolved: mac802154: check local interfaces before deleting sdata list syzkaller reported a corrupted list in ieee802154_if_remove. [1] Remove an IEEE 802.15.4 network interface after unregister an IEEE 802.15.4 hardware device from the system. CPU0 CPU1 ==== ==== genl_family_rcv_msg_doit ieee802154_unregister_hw ieee802154_del_iface ieee802154_remove_interfaces rdev_del_virtual_intf_deprecated list_del(&sdata->list) ieee802154_if_remove list_del_rcu The net device has been unregistered, since the rcu grace period, unregistration must be run before ieee802154_if_remove. To avoid this issue, add a check for local->interfaces before deleting sdata list. [1] kernel BUG at lib/list_debug.c:58! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI CPU: 0 UID: 0 PID: 6277 Comm: syz-executor157 Not tainted 6.12.0-rc6-syzkaller-00005-g557329bcecc2 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 RIP: 0010:__list_del_entry_valid_or_report+0xf4/0x140 lib/list_debug.c:56 Code: e8 a1 7e 00 07 90 0f 0b 48 c7 c7 e0 37 60 8c 4c 89 fe e8 8f 7e 00 07 90 0f 0b 48 c7 c7 40 38 60 8c 4c 89 fe e8 7d 7e 00 07 90 <0f> 0b 48 c7 c7 a0 38 60 8c 4c 89 fe e8 6b 7e 00 07 90 0f 0b 48 c7 RSP: 0018:ffffc9000490f3d0 EFLAGS: 00010246 RAX: 000000000000004e RBX: dead000000000122 RCX: d211eee56bb28d00 RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000 RBP: ffff88805b278dd8 R08: ffffffff8174a12c R09: 1ffffffff2852f0d R10: dffffc0000000000 R11: fffffbfff2852f0e R12: dffffc0000000000 R13: dffffc0000000000 R14: dead000000000100 R15: ffff88805b278cc0 FS: 0000555572f94380(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000056262e4a3000 CR3: 0000000078496000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __list_del_entry_valid include/linux/list.h:124 [inline] __list_del_entry include/linux/list.h:215 [inline] list_del_rcu include/linux/rculist.h:157 [inline] ieee802154_if_remove+0x86/0x1e0 net/mac802154/iface.c:687 rdev_del_virtual_intf_deprecated net/ieee802154/rdev-ops.h:24 [inline] ieee802154_del_iface+0x2c0/0x5c0 net/ieee802154/nl-phy.c:323 genl_family_rcv_msg_doit net/netlink/genetlink.c:1115 [inline] genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline] genl_rcv_msg+0xb14/0xec0 net/netlink/genetlink.c:1210 netlink_rcv_skb+0x1e3/0x430 net/netlink/af_netlink.c:2551 genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219 netlink_unicast_kernel net/netlink/af_netlink.c:1331 [inline] netlink_unicast+0x7f6/0x990 net/netlink/af_netlink.c:1357 netlink_sendmsg+0x8e4/0xcb0 net/netlink/af_netlink.c:1901 sock_sendmsg_nosec net/socket.c:729 [inline] __sock_sendmsg+0x221/0x270 net/socket.c:744 ____sys_sendmsg+0x52a/0x7e0 net/socket.c:2607 ___sys_sendmsg net/socket.c:2661 [inline] __sys_sendmsg+0x292/0x380 net/socket.c:2690 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: RDMA/ipoib: Fix warning caused by destroying non-initial netns After the commit 5ce2dced8e95 ("RDMA/ipoib: Set rtnl_link_ops for ipoib interfaces"), if the IPoIB device is moved to non-initial netns, destroying that netns lets the device vanish instead of moving it back to the initial netns, This is happening because default_device_exit() skips the interfaces due to having rtnl_link_ops set. Steps to reporoduce: ip netns add foo ip link set mlx5_ib0 netns foo ip netns delete foo WARNING: CPU: 1 PID: 704 at net/core/dev.c:11435 netdev_exit+0x3f/0x50 Modules linked in: xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables nfnetlink tun d fuse CPU: 1 PID: 704 Comm: kworker/u64:3 Tainted: G S W 5.13.0-rc1+ #1 Hardware name: Dell Inc. PowerEdge R630/02C2CP, BIOS 2.1.5 04/11/2016 Workqueue: netns cleanup_net RIP: 0010:netdev_exit+0x3f/0x50 Code: 48 8b bb 30 01 00 00 e8 ef 81 b1 ff 48 81 fb c0 3a 54 a1 74 13 48 8b 83 90 00 00 00 48 81 c3 90 00 00 00 48 39 d8 75 02 5b c3 <0f> 0b 5b c3 66 66 2e 0f 1f 84 00 00 00 00 00 66 90 0f 1f 44 00 RSP: 0018:ffffb297079d7e08 EFLAGS: 00010206 RAX: ffff8eb542c00040 RBX: ffff8eb541333150 RCX: 000000008010000d RDX: 000000008010000e RSI: 000000008010000d RDI: ffff8eb440042c00 RBP: ffffb297079d7e48 R08: 0000000000000001 R09: ffffffff9fdeac00 R10: ffff8eb5003be000 R11: 0000000000000001 R12: ffffffffa1545620 R13: ffffffffa1545628 R14: 0000000000000000 R15: ffffffffa1543b20 FS: 0000000000000000(0000) GS:ffff8ed37fa00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005601b5f4c2e8 CR3: 0000001fc8c10002 CR4: 00000000003706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: ops_exit_list.isra.9+0x36/0x70 cleanup_net+0x234/0x390 process_one_work+0x1cb/0x360 ? process_one_work+0x360/0x360 worker_thread+0x30/0x370 ? process_one_work+0x360/0x360 kthread+0x116/0x130 ? kthread_park+0x80/0x80 ret_from_fork+0x22/0x30 To avoid the above warning and later on the kernel panic that could happen on shutdown due to a NULL pointer dereference, make sure to set the netns_refund flag that was introduced by commit 3a5ca857079e ("can: dev: Move device back to init netns on owning netns delete") to properly restore the IPoIB interfaces to the initial netns.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/pm: Update intermediate power state for SI Update the current state as boot state during dpm initialization. During the subsequent initialization, set_power_state gets called to transition to the final power state. set_power_state refers to values from the current state and without current state populated, it could result in NULL pointer dereference. For ex: on platforms where PCI speed change is supported through ACPI ATCS method, the link speed of current state needs to be queried before deciding on changing to final power state's link speed. The logic to query ATCS-support was broken on certain platforms. The issue became visible when broken ATCS-support logic got fixed with commit f9b7f3703ff9 ("drm/amdgpu/acpi: make ATPX/ATCS structures global (v2)"). Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1698

In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix kernel crash when 1588 is received on HIP08 devices The HIP08 devices does not register the ptp devices, so the hdev->ptp is NULL, but the hardware can receive 1588 messages, and set the HNS3_RXD_TS_VLD_B bit, so, if match this case, the access of hdev->ptp->flags will cause a kernel crash: [ 5888.946472] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000018 [ 5888.946475] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000018 ... [ 5889.266118] pc : hclge_ptp_get_rx_hwts+0x40/0x170 [hclge] [ 5889.272612] lr : hclge_ptp_get_rx_hwts+0x34/0x170 [hclge] [ 5889.279101] sp : ffff800012c3bc50 [ 5889.283516] x29: ffff800012c3bc50 x28: ffff2040002be040 [ 5889.289927] x27: ffff800009116484 x26: 0000000080007500 [ 5889.296333] x25: 0000000000000000 x24: ffff204001c6f000 [ 5889.302738] x23: ffff204144f53c00 x22: 0000000000000000 [ 5889.309134] x21: 0000000000000000 x20: ffff204004220080 [ 5889.315520] x19: ffff204144f53c00 x18: 0000000000000000 [ 5889.321897] x17: 0000000000000000 x16: 0000000000000000 [ 5889.328263] x15: 0000004000140ec8 x14: 0000000000000000 [ 5889.334617] x13: 0000000000000000 x12: 00000000010011df [ 5889.340965] x11: bbfeff4d22000000 x10: 0000000000000000 [ 5889.347303] x9 : ffff800009402124 x8 : 0200f78811dfbb4d [ 5889.353637] x7 : 2200000000191b01 x6 : ffff208002a7d480 [ 5889.359959] x5 : 0000000000000000 x4 : 0000000000000000 [ 5889.366271] x3 : 0000000000000000 x2 : 0000000000000000 [ 5889.372567] x1 : 0000000000000000 x0 : ffff20400095c080 [ 5889.378857] Call trace: [ 5889.382285] hclge_ptp_get_rx_hwts+0x40/0x170 [hclge] [ 5889.388304] hns3_handle_bdinfo+0x324/0x410 [hns3] [ 5889.394055] hns3_handle_rx_bd+0x60/0x150 [hns3] [ 5889.399624] hns3_clean_rx_ring+0x84/0x170 [hns3] [ 5889.405270] hns3_nic_common_poll+0xa8/0x220 [hns3] [ 5889.411084] napi_poll+0xcc/0x264 [ 5889.415329] net_rx_action+0xd4/0x21c [ 5889.419911] __do_softirq+0x130/0x358 [ 5889.424484] irq_exit+0x134/0x154 [ 5889.428700] __handle_domain_irq+0x88/0xf0 [ 5889.433684] gic_handle_irq+0x78/0x2c0 [ 5889.438319] el1_irq+0xb8/0x140 [ 5889.442354] arch_cpu_idle+0x18/0x40 [ 5889.446816] default_idle_call+0x5c/0x1c0 [ 5889.451714] cpuidle_idle_call+0x174/0x1b0 [ 5889.456692] do_idle+0xc8/0x160 [ 5889.460717] cpu_startup_entry+0x30/0xfc [ 5889.465523] secondary_start_kernel+0x158/0x1ec [ 5889.470936] Code: 97ffab78 f9411c14 91408294 f9457284 (f9400c80) [ 5889.477950] SMP: stopping secondary CPUs [ 5890.514626] SMP: failed to stop secondary CPUs 0-69,71-95 [ 5890.522951] Starting crashdump kernel...

In the Linux kernel, the following vulnerability has been resolved: vfio/pci: Create persistent INTx handler A vulnerability exists where the eventfd for INTx signaling can be deconfigured, which unregisters the IRQ handler but still allows eventfds to be signaled with a NULL context through the SET_IRQS ioctl or through unmask irqfd if the device interrupt is pending. Ideally this could be solved with some additional locking; the igate mutex serializes the ioctl and config space accesses, and the interrupt handler is unregistered relative to the trigger, but the irqfd path runs asynchronous to those. The igate mutex cannot be acquired from the atomic context of the eventfd wake function. Disabling the irqfd relative to the eventfd registration is potentially incompatible with existing userspace. As a result, the solution implemented here moves configuration of the INTx interrupt handler to track the lifetime of the INTx context object and irq_type configuration, rather than registration of a particular trigger eventfd. Synchronization is added between the ioctl path and eventfd_signal() wrapper such that the eventfd trigger can be dynamically updated relative to in-flight interrupts or irqfd callbacks.

In the Linux kernel, the following vulnerability has been resolved: nfs: fix panic when nfs4_ff_layout_prepare_ds() fails We've been seeing the following panic in production BUG: kernel NULL pointer dereference, address: 0000000000000065 PGD 2f485f067 P4D 2f485f067 PUD 2cc5d8067 PMD 0 RIP: 0010:ff_layout_cancel_io+0x3a/0x90 [nfs_layout_flexfiles] Call Trace: <TASK> ? __die+0x78/0xc0 ? page_fault_oops+0x286/0x380 ? __rpc_execute+0x2c3/0x470 [sunrpc] ? rpc_new_task+0x42/0x1c0 [sunrpc] ? exc_page_fault+0x5d/0x110 ? asm_exc_page_fault+0x22/0x30 ? ff_layout_free_layoutreturn+0x110/0x110 [nfs_layout_flexfiles] ? ff_layout_cancel_io+0x3a/0x90 [nfs_layout_flexfiles] ? ff_layout_cancel_io+0x6f/0x90 [nfs_layout_flexfiles] pnfs_mark_matching_lsegs_return+0x1b0/0x360 [nfsv4] pnfs_error_mark_layout_for_return+0x9e/0x110 [nfsv4] ? ff_layout_send_layouterror+0x50/0x160 [nfs_layout_flexfiles] nfs4_ff_layout_prepare_ds+0x11f/0x290 [nfs_layout_flexfiles] ff_layout_pg_init_write+0xf0/0x1f0 [nfs_layout_flexfiles] __nfs_pageio_add_request+0x154/0x6c0 [nfs] nfs_pageio_add_request+0x26b/0x380 [nfs] nfs_do_writepage+0x111/0x1e0 [nfs] nfs_writepages_callback+0xf/0x30 [nfs] write_cache_pages+0x17f/0x380 ? nfs_pageio_init_write+0x50/0x50 [nfs] ? nfs_writepages+0x6d/0x210 [nfs] ? nfs_writepages+0x6d/0x210 [nfs] nfs_writepages+0x125/0x210 [nfs] do_writepages+0x67/0x220 ? generic_perform_write+0x14b/0x210 filemap_fdatawrite_wbc+0x5b/0x80 file_write_and_wait_range+0x6d/0xc0 nfs_file_fsync+0x81/0x170 [nfs] ? nfs_file_mmap+0x60/0x60 [nfs] __x64_sys_fsync+0x53/0x90 do_syscall_64+0x3d/0x90 entry_SYSCALL_64_after_hwframe+0x46/0xb0 Inspecting the core with drgn I was able to pull this >>> prog.crashed_thread().stack_trace()[0] #0 at 0xffffffffa079657a (ff_layout_cancel_io+0x3a/0x84) in ff_layout_cancel_io at fs/nfs/flexfilelayout/flexfilelayout.c:2021:27 >>> prog.crashed_thread().stack_trace()[0]['idx'] (u32)1 >>> prog.crashed_thread().stack_trace()[0]['flseg'].mirror_array[1].mirror_ds (struct nfs4_ff_layout_ds *)0xffffffffffffffed This is clear from the stack trace, we call nfs4_ff_layout_prepare_ds() which could error out initializing the mirror_ds, and then we go to clean it all up and our check is only for if (!mirror->mirror_ds). This is inconsistent with the rest of the users of mirror_ds, which have if (IS_ERR_OR_NULL(mirror_ds)) to keep from tripping over this exact scenario. Fix this up in ff_layout_cancel_io() to make sure we don't panic when we get an error. I also spot checked all the other instances of checking mirror_ds and we appear to be doing the correct checks everywhere, only unconditionally dereferencing mirror_ds when we know it would be valid.

In the Linux kernel, the following vulnerability has been resolved: dmaengine: ti: edma: Add some null pointer checks to the edma_probe devm_kasprintf() returns a pointer to dynamically allocated memory which can be NULL upon failure. Ensure the allocation was successful by checking the pointer validity.