An Improper Release of Memory Before Removing Last Reference vulnerability in Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows a local, low privileged attacker to cause an FPC crash, leading to Denial of Service (DoS). On all Junos MX Series with MPC1 - MPC9, LC480, LC2101, MX10003, and MX80, when Connectivity-Fault-Management (CFM) is enabled in a VPLS scenario, and a specific LDP related command is run, an FPC will crash and reboot. Continued execution of this specific LDP command can lead to sustained Denial of Service condition. This issue affects: Juniper Networks Junos OS on MX Series: * All versions prior to 20.4R3-S7; * 21.1 versions prior to 21.1R3-S5; * 21.2 versions prior to 21.2R3-S4; * 21.3 versions prior to 21.3R3-S4; * 21.4 versions prior to 21.4R3-S3; * 22.1 versions prior to 22.1R3-S1; * 22.2 versions prior to 22.2R2-S1, 22.2R3; * 22.3 versions prior to 22.3R1-S2, 22.3R2.

A Missing Release of Memory after Effective Lifetime vulnerability in the routing protocol daemon of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network based attacker to cause a Denial of Service (DoS). In a BGP rib sharding scenario, when an attribute of an active BGP route is updated memory will leak. As rpd memory usage increases over time the rpd process will eventually run out of memory, crash, and restart. The memory utilization can be monitored with the following CLI commands: show task memory show system processes extensive | match rpd This issue affects: Juniper Networks Junos OS 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2. Juniper Networks Junos OS Evolved 20.3-EVO version 20.3R1-EVO and later versions; 20.4-EVO versions prior to 20.4R3-S6-EVO; 21.2-EVO versions prior to 21.2R3-EVO; 21.3-EVO versions prior to 21.3R2-EVO.

A Missing Release of Memory after Effective Lifetime vulnerability in the Flow Processing Daemon (flowd) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). In an IPsec VPN environment, a memory leak will be seen if a DH or ECDH group is configured. Eventually the flowd process will crash and restart. This issue affects Juniper Networks Junos OS on SRX Series: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S10; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2.

A Missing Release of Memory after Effective Lifetime vulnerability in the Anti-Virus processing of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). On all SRX platforms with Anti-Virus enabled, if a server sends specific content in the HTTP body of a response to a client request, these packets are queued by Anti-Virus processing in Juniper Buffers (jbufs) which are never released. When these jbufs are exhausted, the device stops forwarding all transit traffic. A jbuf memory leak can be noticed from the following logs: (<node>.)<fpc> Warning: jbuf pool id <#> utilization level (<current level>%) is above <threshold>%! To recover from this issue, the affected device needs to be manually rebooted to free the leaked jbufs. This issue affects Junos OS on SRX Series:  * all versions before 21.2R3-S9, * 21.4 versions before 21.4R3-S10, * 22.2 versions before 22.2R3-S6, * 22.4 versions before 22.4R3-S6, * 23.2 versions before 23.2R2-S3, * 23.4 versions before 23.4R2-S3, * 24.2 versions before 24.2R2.

A Missing Release of Memory after Effective Lifetime vulnerability in the routing process daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an attacker to send a malformed BGP Path attribute update which allocates memory used to log the bad path attribute. This memory is not properly freed in all circumstances, leading to a Denial of Service (DoS). Consumed memory can be freed by manually restarting Routing Protocol Daemon (rpd). Memory utilization could be monitored by:  user@host> show system memory or show system monitor memory status This issue affects: Junos OS:  * All versions before 21.2R3-S8,  * from 21.4 before 21.4R3-S8, * from 22.2 before 22.2R3-S4,  * from 22.3 before 22.3R3-S3,  * from 22.4 before 22.4R3-S3, * from 23.2 before 23.2R2-S1,  * from 23.4 before 23.4R1-S2, 23.4R2. Junos OS Evolved: * All versions before 21.2R3-S8-EVO, * from 21.4 before 21.4R3-S8-EVO, * from 22.2 before 22.2R3-S4-EVO, * from 22.3 before 22.3R3-S3-EVO, * from 22.4 before 22.4R3-S3-EVO, * from 23.2 before 23.2R2-S1-EVO, * from 23.4 before 23.4R1-S2-EVO, 23.4R2-EVO.

An Improper Validation of Specified Type of Input vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS allows an attacker to cause an RPD memory leak leading to a Denial of Service (DoS). This memory leak only occurs when the attacker's packets are destined to any configured IPv6 address on the device. This issue affects: Juniper Networks Junos OS 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2; 22.1 versions prior to 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 21.1R1.

A Missing Release of Memory after Effective Lifetime vulnerability in the Juniper Tunnel Driver (jtd) of Juniper Networks Junos OS Evolved allows an unauthenticated network-based attacker to cause Denial of Service.  Receipt of specifically malformed IPv6 packets, destined to the device, causes kernel memory to not be freed, resulting in memory exhaustion leading to a system crash and Denial of Service (DoS). Continuous receipt and processing of these packets will continue to exhaust kernel memory, creating a sustained Denial of Service (DoS) condition. This issue only affects systems configured with IPv6. This issue affects Junos OS Evolved:  * from 22.4-EVO before 22.4R3-S5-EVO,  * from 23.2-EVO before 23.2R2-S2-EVO,  * from 23.4-EVO before 23.4R2-S2-EVO,  * from 24.2-EVO before 24.2R1-S2-EVO, 24.2R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 22.4R1-EVO.

An Improper Validation of Specified Type of Input vulnerability in the packet forwarding engine (pfe) Juniper Networks Junos OS on SRX5000 Series allows an unauthenticated, network based attacker to cause a Denial of Service (Dos). When a non-clustered SRX5000 device receives a specifically malformed packet this will cause a flowd crash and restart. This issue affects Junos OS: * 22.1 releases 22.1R1 and later before 22.2R3-S5, * 22.3 releases before 22.3R3-S4, * 22.4 releases before 22.4R3-S4, * 23.2 releases before 23.2R2-S2, * 23.4 releases before 23.4R2-S1, * 24.2 releases before 24.2R1-S1, 24.2R2. Please note that the PR does indicate that earlier versions have been fixed as well, but these won't be adversely impacted by this.

A Missing Release of Memory after Effective Lifetime vulnerability in Juniper Networks Junos OS on MX Series allows an unauthenticated adjacent attacker to cause a Denial-of-Service (DoS). In a subscriber management scenario continuous subscriber logins will trigger a memory leak and eventually lead to an FPC crash and restart. This issue affects Junos OS on MX Series: * All version before 21.2R3-S6, * 21.4 versions before 21.4R3-S6, * 22.1 versions before 22.1R3-S5, * 22.2 versions before 22.2R3-S3,  * 22.3 versions before 22.3R3-S2, * 22.4 versions before 22.4R3, * 23.2 versions before 23.2R2.

A Missing Release of Memory after Effective Lifetime vulnerability in the Periodic Packet Management Daemon (ppmd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated adjacent attacker to cause a Denial-of-Service (DoS). When a BFD session configured with authentication flaps, ppmd memory can leak. Whether the leak happens depends on a race condition which is outside the attackers control. This issue only affects BFD operating in distributed aka delegated (which is the default behavior) or inline mode. Whether the leak occurs can be monitored with the following CLI command: > show ppm request-queue FPC     Pending-request fpc0                   2 request-total-pending: 2 where a continuously increasing number of pending requests is indicative of the leak.  This issue affects: Junos OS: * All versions before 21.2R3-S8, * 21.4 versions before 21.4R3-S7, * 22.1 versions before 22.1R3-S4, * 22.2 versions before 22.2R3-S4, * 22.3 versions before 22.3R3, * 22.4 versions before 22.4R2-S2, 22.4R3. Junos OS Evolved: * All versions before 21.2R3-S8-EVO, * 21.4-EVO versions before 21.4R3-S7-EVO, * 22.2-EVO versions before 22.2R3-S4-EVO, * 22.3-EVO versions before 22.3R3-EVO, * 22.4-EVO versions before 22.4R3-EVO.

A memory leak vulnerability in the of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the device by sending specific commands from a peered BGP host and having those BGP states delivered to the vulnerable device. This issue affects: Juniper Networks Junos OS: 18.1 versions prior to 18.1R2-S4, 18.1R3-S1; 18.1X75 all versions. Versions before 18.1R1 are not affected.

On Juniper Networks SRX Series devices with link aggregation (lag) configured, executing any operation that fetches Aggregated Ethernet (AE) interface statistics, including but not limited to SNMP GET requests, causes a slow kernel memory leak. If all the available memory is consumed, the traffic will be impacted and a reboot might be required. The following log can be seen if this issue happens. /kernel: rt_pfe_veto: Memory over consumed. Op 1 err 12, rtsm_id 0:-1, msg type 72 /kernel: rt_pfe_veto: free kmem_map memory = (20770816) curproc = kmd An administrator can use the following CLI command to monitor the status of memory consumption (ifstat bucket): user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 2588977 162708K - 19633958 <<<< user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 3021629 189749K - 22914415 <<<< This issue affects Juniper Networks Junos OS on SRX Series: 17.1 versions 17.1R3 and above prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S5; 18.2 versions prior to 18.2R3-S7, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS prior to 17.1R3.

An Improper Validation of Specified Type of Input vulnerability in Routing Protocol Daemon (RPD) of Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). If a BGP update is received over an established BGP session which contains a tunnel encapsulation attribute with a specifically malformed TLV, rpd will crash and restart. This issue affects: Junos OS: * all versions before 21.2R3-S7,  * from 21.3 before 21.3R3-S5,  * from 21.4 before 21.4R3-S5,  * from 22.1 before 22.1R3-S5,  * from 22.2 before 22.2R3-S3,  * from 22.3 before 22.3R3-S2,  * from 22.4 before 22.4R3,  * from 23.2 before 23.2R1-S2, 23.2R2. Junos OS Evolved: * all versions before 21.2R3-S7-EVO,  * from 21.3-EVO before 21.3R3-S5-EVO,  * from 21.4-EVO before 21.4R3-S5-EVO,  * from 22.2-EVO before 22.2R3-S3-EVO,  * from 22.3-EVO before 22.3R3-S2-EVO,  * from 22.4-EVO before 22.4R3-EVO,  * from 23.2-EVO before 23.2R1-S2-EVO, 23.2R2-EVO. This is a related but separate issue than the one described in JSA75739

A memory leak in the Silicon Labs' Bluetooth stack for EFR32 products may cause memory to be exhausted when sending notifications to multiple clients, this results in all Bluetooth operations, such as advertising and scanning, to stop.

Multiple vulnerabilities in the Link Layer Discovery Protocol (LLDP) implementation for Cisco Video Surveillance 7000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. These vulnerabilities are due to incorrect processing of certain LLDP packets at ingress time. An attacker could exploit these vulnerabilities by sending crafted LLDP packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DoS condition. Note: LLDP is a Layer 2 protocol. To exploit these vulnerabilities, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

Multiple vulnerabilities exist in the Link Layer Discovery Protocol (LLDP) implementation for Cisco Small Business RV Series Routers. An unauthenticated, adjacent attacker could execute arbitrary code or cause an affected router to leak system memory or reload. A memory leak or device reload would cause a denial of service (DoS) condition on an affected device. For more information about these vulnerabilities, see the Details section of this advisory. Note: LLDP is a Layer 2 protocol. To exploit these vulnerabilities, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

Multiple vulnerabilities in the implementation of the Cisco Discovery Protocol and Link Layer Discovery Protocol (LLDP) for Cisco Video Surveillance 7000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. These vulnerabilities are due to incorrect processing of certain Cisco Discovery Protocol and LLDP packets at ingress time. An attacker could exploit these vulnerabilities by sending crafted Cisco Discovery Protocol or LLDP packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DoS condition. Note: Cisco Discovery Protocol and LLDP are Layer 2 protocols. To exploit these vulnerabilities, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

Multiple vulnerabilities in the Link Layer Discovery Protocol (LLDP) implementation for Cisco Video Surveillance 7000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. These vulnerabilities are due to incorrect processing of certain LLDP packets at ingress time. An attacker could exploit these vulnerabilities by sending crafted LLDP packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DoS condition. Note: LLDP is a Layer 2 protocol. To exploit these vulnerabilities, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

HUAWEI P30 smartphones with versions earlier than 10.1.0.160(C00E160R2P11) have a denial of service vulnerability. A module does not deal with mal-crafted messages and it leads to memory leak. Attackers can exploit this vulnerability to make the device denial of service.Affected product versions include: HUAWEI P30 versions Versions earlier than 10.1.0.160(C00E160R2P11).

A vulnerability in the Cisco Discovery Protocol of Cisco Video Surveillance 8000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. The vulnerability is due to incorrect processing of certain Cisco Discovery Protocol packets. An attacker could exploit this vulnerability by sending certain Cisco Discovery Protocol packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DOS condition. Note: Cisco Discovery Protocol is a Layer 2 protocol. To exploit this vulnerability, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

A vulnerability in the Cisco Discovery Protocol of Cisco Video Surveillance 8000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. The vulnerability is due to incorrect processing of certain Cisco Discovery Protocol packets. An attacker could exploit this vulnerability by sending certain Cisco Discovery Protocol packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DOS condition. Note: Cisco Discovery Protocol is a Layer 2 protocol. To exploit this vulnerability, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

BlueZ is a Bluetooth protocol stack for Linux. In affected versions a vulnerability exists in sdp_cstate_alloc_buf which allocates memory which will always be hung in the singly linked list of cstates and will not be freed. This will cause a memory leak over time. The data can be a very large object, which can be caused by an attacker continuously sending sdp packets and this may cause the service of the target device to crash.

Improper validation of specified type of input for some Intel(R) PROSet/Wireless and Intel(R) Killer(TM) Wi-Fi software before version 22.240 may allow an unauthenticated user to potentially enable denial of service via adjacent access.

A vulnerability in the Link Layer Discovery Protocol (LLDP) feature for Cisco Nexus 9000 Series Fabric Switches in Application Centric Infrastructure (ACI) Mode could allow an unauthenticated, adjacent attacker to cause a memory leak, which could result in an unexpected reload of the device. This vulnerability is due to incorrect error checking when parsing ingress LLDP packets. An attacker could exploit this vulnerability by sending a steady stream of crafted LLDP packets to an affected device. A successful exploit could allow the attacker to cause a memory leak, which could result in a denial of service (DoS) condition when the device unexpectedly reloads. Note: This vulnerability cannot be exploited by transit traffic through the device. The crafted LLDP packet must be targeted to a directly connected interface, and the attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent). In addition, the attack surface for this vulnerability can be reduced by disabling LLDP on interfaces where it is not required.

A memory leak in the EFR32 Bluetooth LE stack 5.1.0 through 5.1.1 allows an attacker to send an invalid pairing message and cause future legitimate connection attempts to fail. A reset of the device immediately clears the error.

CloudEngine 12800 has a DoS vulnerability. An attacker of a neighboring device sends a large number of specific packets. As a result, a memory leak occurs after the device uses the specific packet. As a result, the attacker can exploit this vulnerability to cause DoS attacks on the target device.

A vulnerability in the WLAN Control Protocol (WCP) implementation for Cisco Aironet Access Point (AP) software could allow an unauthenticated, adjacent attacker to cause a reload of an affected device, resulting in a denial of service (DoS) condition. This vulnerability is due to incorrect error handling when an affected device receives an unexpected 802.11 frame. An attacker could exploit this vulnerability by sending certain 802.11 frames over the wireless network to an interface on an affected AP. A successful exploit could allow the attacker to cause a packet buffer leak. This could eventually result in buffer allocation failures, which would trigger a reload of the affected device.

D-Link DIR-3040 prog.cgi websSecurityHandler Memory Leak Denial-of-Service Vulnerability. This vulnerability allows network-adjacent attackers to create a denial-of-service condition on affected installations of D-Link DIR-3040 routers. Authentication is not required to exploit this vulnerability. The specific flaw exists within the prog.cgi program, which handles HNAP requests made to the lighttpd webserver listening on ports 80 and 443. The issue results from the lack of proper memory management when processing HTTP cookie values. An attacker can leverage this vulnerability to create a denial-of-service condition on the system. . Was ZDI-CAN-21668.

A missing release of memory after effective lifetime vulnerability in FortiSwitch 6.4.0 to 6.4.6, 6.2.0 to 6.2.6, 6.0.0 to 6.0.6, 3.6.11 and below may allow an attacker on an adjacent network to exhaust available memory by sending specifically crafted LLDP/CDP/EDP packets to the device.

Multiple vulnerabilities in the Link Layer Discovery Protocol (LLDP) implementation for Cisco Video Surveillance 7000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. These vulnerabilities are due to incorrect processing of certain LLDP packets at ingress time. An attacker could exploit these vulnerabilities by sending crafted LLDP packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DoS condition. Note: LLDP is a Layer 2 protocol. To exploit these vulnerabilities, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

Multiple vulnerabilities in the Link Layer Discovery Protocol (LLDP) implementation for Cisco Video Surveillance 7000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. These vulnerabilities are due to incorrect processing of certain LLDP packets at ingress time. An attacker could exploit these vulnerabilities by sending crafted LLDP packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DoS condition. Note: LLDP is a Layer 2 protocol. To exploit these vulnerabilities, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

Multiple vulnerabilities in the implementation of the Cisco Discovery Protocol and Link Layer Discovery Protocol (LLDP) for Cisco Video Surveillance 7000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. These vulnerabilities are due to incorrect processing of certain Cisco Discovery Protocol and LLDP packets at ingress time. An attacker could exploit these vulnerabilities by sending crafted Cisco Discovery Protocol or LLDP packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DoS condition. Note: Cisco Discovery Protocol and LLDP are Layer 2 protocols. To exploit these vulnerabilities, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

Multiple vulnerabilities exist in the Link Layer Discovery Protocol (LLDP) implementation for Cisco Small Business RV Series Routers. An unauthenticated, adjacent attacker could execute arbitrary code or cause an affected router to leak system memory or reload. A memory leak or device reload would cause a denial of service (DoS) condition on an affected device. For more information about these vulnerabilities, see the Details section of this advisory. Note: LLDP is a Layer 2 protocol. To exploit these vulnerabilities, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).