On Juniper Networks SRX Series devices with link aggregation (lag) configured, executing any operation that fetches Aggregated Ethernet (AE) interface statistics, including but not limited to SNMP GET requests, causes a slow kernel memory leak. If all the available memory is consumed, the traffic will be impacted and a reboot might be required. The following log can be seen if this issue happens. /kernel: rt_pfe_veto: Memory over consumed. Op 1 err 12, rtsm_id 0:-1, msg type 72 /kernel: rt_pfe_veto: free kmem_map memory = (20770816) curproc = kmd An administrator can use the following CLI command to monitor the status of memory consumption (ifstat bucket): user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 2588977 162708K - 19633958 <<<< user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 3021629 189749K - 22914415 <<<< This issue affects Juniper Networks Junos OS on SRX Series: 17.1 versions 17.1R3 and above prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S5; 18.2 versions prior to 18.2R3-S7, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS prior to 17.1R3.

On Juniper Networks Junos OS devices with Multipath or add-path feature enabled, processing a specific BGP UPDATE can lead to a routing process daemon (RPD) crash and restart, causing a Denial of Service (DoS). Continued receipt and processing of this UPDATE message will create a sustained Denial of Service (DoS) condition. This BGP UPDATE message can propagate to other BGP peers with vulnerable Junos versions on which Multipath or add-path feature is enabled, and cause RPD to crash and restart. This issue affects both IBGP and EBGP deployments in IPv4 or IPv6 network. Junos OS devices that do not have the BGP Multipath or add-path feature enabled are not affected by this issue. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S18; 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R3-S3;

On Juniper Networks MX Series and EX9200 Series platforms with Trio-based MPC (Modular Port Concentrator) where Integrated Routing and Bridging (IRB) interface is configured and it is mapped to a VPLS instance or a Bridge-Domain, certain network events at Customer Edge (CE) device may cause memory leak in the MPC which can cause an out of memory and MPC restarts. When this issue occurs, there will be temporary traffic interruption until the MPC is restored. An administrator can use the following CLI command to monitor the status of memory usage level of the MPC: user@device> show system resource-monitor fpc FPC Resource Usage Summary Free Heap Mem Watermark : 20 % Free NH Mem Watermark : 20 % Free Filter Mem Watermark : 20 % * - Watermark reached Slot # % Heap Free RTT Average RTT 1 87 PFE # % ENCAP mem Free % NH mem Free % FW mem Free 0 NA 88 99 1 NA 89 99 When the issue is occurring, the value of “% NH mem Free” will go down until the MPC restarts. This issue affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines). Please refer to https://kb.juniper.net/KB25385 for the list of Trio-based PFEs. This issue affects Juniper Networks Junos OS on MX Series, EX9200 Series: 17.3R3-S8; 17.4R3-S2; 18.2R3-S4, 18.2R3-S5; 18.3R3-S2, 18.3R3-S3; 18.4 versions starting from 18.4R3-S1 and later versions prior to 18.4R3-S6; 19.2 versions starting from 19.2R2 and later versions prior to 19.2R3-S1; 19.4 versions starting from 19.4R2 and later versions prior to 19.4R2-S3, 19.4R3; 20.2 versions starting from 20.2R1 and later versions prior to 20.2R1-S3, 20.2R2. This issue does not affect Juniper Networks Junos OS: 18.1, 19.1, 19.3, 20.1.

A buffer overflow vulnerability in the TCP/IP stack of Juniper Networks Junos OS allows an attacker to send specific sequences of packets to the device thereby causing a Denial of Service (DoS). By repeatedly sending these sequences of packets to the device, an attacker can sustain the Denial of Service (DoS) condition. The device will abnormally shut down as a result of these sent packets. A potential indicator of compromise will be the following message in the log files: "eventd[13955]: SYSTEM_ABNORMAL_SHUTDOWN: System abnormally shut down" These issue are only triggered by traffic destined to the device. Transit traffic will not trigger these issues. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S19; 15.1 versions prior to 15.1R7-S10; 16.1 version 16.1R1 and later versions; 16.2 version 16.2R1 and later versions; 17.1 version 17.1R1 and later versions; 17.2 version 17.2R1 and later versions; 17.3 versions prior to 17.3R3-S12; 17.4 version 17.4R1 and later versions; 18.1 versions prior to 18.1R3-S13; 18.2 version 18.2R1 and later versions; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2; 21.2 versions prior to 21.2R1-S1, 21.2R2.

An uncontrolled resource consumption vulnerability in Juniper Networks Junos OS on QFX5000 Series and EX4600 Series switches allows an attacker sending large amounts of legitimate traffic destined to the device to cause Interchassis Control Protocol (ICCP) interruptions, leading to an unstable control connection between the Multi-Chassis Link Aggregation Group (MC-LAG) nodes which can in turn lead to traffic loss. Continued receipt of this amount of traffic will create a sustained Denial of Service (DoS) condition. An indication that the system could be impacted by this issue is the following log message: "DDOS_PROTOCOL_VIOLATION_SET: Warning: Host-bound traffic for protocol/exception LOCALNH:aggregate exceeded its allowed bandwidth at fpc <fpc number> for <n> times, started at <timestamp>" This issue affects Juniper Networks Junos OS on QFX5000 Series and EX4600 Series: 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S7; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R1-S1, 20.4R2.

On PTX Series and QFX10k Series devices with the "inline-jflow" feature enabled, a use after free weakness in the Packet Forwarding Engine (PFE) microkernel architecture of Juniper Networks Junos OS may allow an attacker to cause a Denial of Service (DoS) condition whereby one or more Flexible PIC Concentrators (FPCs) may restart. As this is a race condition situation this issue become more likely to be hit when network instability occurs, such as but not limited to BGP/IGP reconvergences, and/or further likely to occur when more active "traffic flows" are occurring through the device. When this issue occurs, it will cause one or more FPCs to restart unexpectedly. During FPC restarts core files will be generated. While the core file is generated traffic will be disrupted. Sustained receipt of large traffic flows and reconvergence-like situations may sustain the Denial of Service (DoS) situation. This issue affects: Juniper Networks Junos OS: 18.1 version 18.1R2 and later versions prior to 18.1R3-S10 on PTX Series, QFX10K Series.

Due to an Improper Initialization vulnerability in Juniper Networks Junos OS on PTX platforms and QFX10K Series with Paradise (PE) chipset-based line cards, ddos-protection configuration changes made from the CLI will not take effect as expected beyond the default DDoS (Distributed Denial of Service) settings in the Packet Forwarding Engine (PFE). This may cause BFD sessions to flap when a high rate of specific packets are received. Flapping of BFD sessions in turn may impact routing protocols and network stability, leading to a Denial of Service (DoS) condition. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects only the following platforms with Paradise (PE) chipset-based line cards: PTX1000, PTX3000 (NextGen), PTX5000, PTX10008, PTX10016 Series and QFX10002 Series. This issue affects: Juniper Networks Junos OS 17.4 versions prior to 17.4R3-S5 on PTX Series, QFX10K Series; 18.2 versions prior to 18.2R3-S8 on PTX Series, QFX10K Series; 18.3 versions prior to 18.3R3-S5 on PTX Series, QFX10K Series; 18.4 versions prior to 18.4R2-S8 on PTX Series, QFX10K Series; 19.1 versions prior to 19.1R3-S5 on PTX Series, QFX10K Series; 19.2 versions prior to 19.2R3-S2 on PTX Series, QFX10K Series; 19.3 versions prior to 19.3R3-S2 on PTX Series, QFX10K Series; 19.4 versions prior to 19.4R3-S2 on PTX Series, QFX10K Series; 20.1 versions prior to 20.1R3 on PTX Series, QFX10K Series; 20.2 versions prior to 20.2R2-S3, 20.2R3 on PTX Series, QFX10K Series; 20.3 versions prior to 20.3R2 on PTX Series, QFX10K Series; 20.4 versions prior to 20.4R2 on PTX Series, QFX10K Series.

In segment routing traffic engineering (SRTE) environments where the BGP Monitoring Protocol (BMP) feature is enable, a vulnerability in the Routing Protocol Daemon (RPD) process of Juniper Networks Junos OS allows an attacker to send a specific crafted BGP update message causing the RPD service to core, creating a Denial of Service (DoS) Condition. Continued receipt and processing of this update message will create a sustained Denial of Service (DoS) condition. This issue affects IPv4 and IPv6 environments. This issue affects: Juniper Networks Junos OS 17.4 versions 17.4R1 and above prior to 17.4R2-S6, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R3; 19.1 versions prior to 19.1R1-S4, 19.1R2; 19.2 versions prior to 19.2R1-S3, 19.2R2, This issue does not affect Junos OS releases prior to 17.4R1. This issue affects: Juniper Networks Junos OS Evolved 19.2-EVO versions prior to 19.2R2-EVO.

A vulnerability in the HTTP/HTTPS service used by J-Web, Web Authentication, Dynamic-VPN (DVPN), Firewall Authentication Pass-Through with Web-Redirect, and Captive Portal allows an unauthenticated attacker to cause an extended Denial of Service (DoS) for these services by sending a high number of specific requests. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S17 on EX Series; 12.3X48 versions prior to 12.3X48-D105 on SRX Series; 15.1 versions prior to 15.1R7-S8; 15.1X49 versions prior to 15.1X49-D230 on SRX Series; 16.1 versions prior to 16.1R7-S8; 17.4 versions prior to 17.4R2-S12, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2; 20.2 versions prior to 20.2R1-S1, 20.2R2.

On Juniper Networks Junos OS devices configured with BGP origin validation using Resource Public Key Infrastructure (RPKI) receipt of a specific packet from the RPKI cache server may cause routing process daemon (RPD) to crash and restart, creating a Denial of Service (DoS) condition. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S8; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R2-S2-EVO.

A vulnerability in the handling of exceptional conditions in Juniper Networks Junos OS Evolved (EVO) allows an attacker to send specially crafted packets to the device, causing the Advanced Forwarding Toolkit manager (evo-aftmand-bt or evo-aftmand-zx) process to crash and restart, impacting all traffic going through the FPC, resulting in a Denial of Service (DoS). Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. Following messages will be logged prior to the crash: Feb 2 10:14:39 fpc0 evo-aftmand-bt[16263]: [Error] Nexthop: Failed to get fwd nexthop for nexthop:32710470974358 label:1089551617 for session:18 probe:35 Feb 2 10:14:39 fpc0 evo-aftmand-bt[16263]: [Error] Nexthop: Failed to get fwd nexthop for nexthop:19241453497049 label:1089551617 for session:18 probe:37 Feb 2 10:14:39 fpc0 evo-aftmand-bt[16263]: [Error] Nexthop: Failed to get fwd nexthop for nexthop:19241453497049 label:1089551617 for session:18 probe:44 Feb 2 10:14:39 fpc0 evo-aftmand-bt[16263]: [Error] Nexthop: Failed to get fwd nexthop for nexthop:32710470974358 label:1089551617 for session:18 probe:47 Feb 2 10:14:39 fpc0 audit[16263]: ANOM_ABEND auid=4294967295 uid=0 gid=0 ses=4294967295 pid=16263 comm="EvoAftManBt-mai" exe="/usr/sbin/evo-aftmand-bt" sig=11 Feb 2 10:14:39 fpc0 kernel: audit: type=1701 audit(1612260879.272:17): auid=4294967295 uid=0 gid=0 ses=4294967295 pid=16263 comm="EvoAftManBt-mai" exe="/usr/sbin/evo-aftmand-bt" sig=1 This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R2-EVO; 21.1 versions prior to 21.1R2-EVO.

An Access of Uninitialized Pointer vulnerability in SIP Application Layer Gateway (ALG) of Juniper Networks Junos OS on SRX Series and MX Series allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When specific valid SIP packets are received the PFE will crash and restart. This issue affects Juniper Networks Junos OS on SRX Series and MX Series: 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R2-S2, 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2; 22.1 versions prior to 22.1R1-S1, 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based, attacker to cause Denial of Service (DoS). A PFE crash will happen when a GPRS Tunnel Protocol (GTP) packet is received with a malformed field in the IP header of GTP encapsulated General Packet Radio Services (GPRS) traffic. The packet needs to match existing state which is outside the attackers control, so the issue cannot be directly exploited. The issue will only be observed when endpoint address validation is enabled. This issue affects Juniper Networks Junos OS on SRX Series: 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2; 22.1 versions prior to 22.1R1-S1, 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.2R1.

A NULL Pointer Dereference vulnerability in the Packet Forwarding Engine of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). On SRX Series If Unified Threat Management (UTM) Enhanced Content Filtering (CF) is enabled and specific transit traffic is processed the PFE will crash and restart. This issue affects Juniper Networks Junos OS: 21.4 versions prior to 21.4R1-S2, 21.4R2 on SRX Series; 22.1 versions prior to 22.1R1-S1, 22.1R2 on SRX Series. This issue does not affect Juniper Networks Junos OS versions prior to 21.4R1.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated networked attacker to cause a Denial of Service (DoS) by sending specific packets over VXLAN which cause the PFE to reset. This issue affects: Juniper Networks Junos OS 19.4 versions prior to 19.4R3-S7; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S1; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R2; 21.3 versions prior to 21.3R1-S1, 21.3R2. This issue does not affect versions of Junos OS prior to 19.4R1.

An Improper Validation of Specified Type of Input vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS allows an attacker to cause an RPD memory leak leading to a Denial of Service (DoS). This memory leak only occurs when the attacker's packets are destined to any configured IPv6 address on the device. This issue affects: Juniper Networks Junos OS 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2; 22.1 versions prior to 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 21.1R1.

An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker to cause a Denial of Service (DoS). If a BGP update message is received over an established BGP session, and that message contains a specific, optional transitive attribute, this session will be torn down with an update message error. This issue cannot propagate beyond an affected system as the processing error occurs as soon as the update is received. This issue is exploitable remotely as the respective attribute will propagate through unaffected systems and intermediate AS (if any). Continuous receipt of a BGP update containing this attribute will create a sustained Denial of Service (DoS) condition. Since this issue only affects 22.3R1, Juniper strongly encourages customers to move to 22.3R1-S1. Juniper SIRT felt that the need to promptly warn customers about this issue affecting the 22.3R1 versions of Junos OS and Junos OS Evolved warranted an Out of Cycle JSA. This issue affects: Juniper Networks Junos OS version 22.3R1. Juniper Networks Junos OS Evolved version 22.3R1-EVO. This issue does not affect: Juniper Networks Junos OS versions prior to 22.3R1. Juniper Networks Junos OS Evolved versions prior to 22.3R1-EVO.

A limitless resource allocation vulnerability in FPC resources of Juniper Networks Junos OS Evolved on PTX Series allows an unprivileged attacker to cause Denial of Service (DoS). Continuously polling the SNMP jnxCosQstatTable causes the FPC to run out of GUID space, causing a Denial of Service to the FPC resources. When the FPC runs out of the GUID space, you will see the following syslog messages. The evo-aftmand-bt process is asserting. fpc1 evo-aftmand-bt[17556]: %USER-3: get_next_guid: Ran out of Guid Space start 1748051689472 end 1752346656767 fpc1 audit[17556]: %AUTH-5: ANOM_ABEND auid=4294967295 uid=0 gid=0 ses=4294967295 pid=17556 comm="EvoAftManBt-mai" exe="/usr/sbin/evo-aftmand-bt" sig=6 fpc1 kernel: %KERN-5: audit: type=1701 audit(1648567505.119:57): auid=4294967295 uid=0 gid=0 ses=4294967295 pid=17556 comm="EvoAftManBt-mai" exe="/usr/sbin/evo-aftmand-bt" sig=6 fpc1 emfd-fpa[14438]: %USER-5: Alarm set: APP color=red, class=CHASSIS, reason=Application evo-aftmand-bt fail on node Fpc1 fpc1 emfd-fpa[14438]: %USER-3-EMF_FPA_ALARM_REP: RaiseAlarm: Alarm(Location: /Chassis[0]/Fpc[1] Module: sysman Object: evo-aftmand-bt:0 Error: 2) reported fpc1 sysepochman[12738]: %USER-5-SYSTEM_REBOOT_EVENT: Reboot [node] [ungraceful reboot] [evo-aftmand-bt exited] The FPC resources can be monitored using the following commands: user@router> start shell [vrf:none] user@router-re0:~$ cli -c "show platform application-info allocations app evo-aftmand-bt" | grep ^fpc | grep -v Route | grep -i -v Nexthop | awk '{total[$1] += $5} END { for (key in total) { print key " " total[key]/4294967296 }}' Once the FPCs become unreachable they must be manually restarted as they do not self-recover. This issue affects Juniper Networks Junos OS Evolved on PTX Series: All versions prior to 20.4R3-S4-EVO; 21.1-EVO version 21.1R1-EVO and later versions; 21.2-EVO version 21.2R1-EVO and later versions; 21.3-EVO versions prior to 21.3R3-EVO; 21.4-EVO versions prior to 21.4R2-EVO; 22.1-EVO versions prior to 22.1R2-EVO.

A release of illegal memory vulnerability in the snmpd daemon of Juniper Networks Junos OS, Junos OS Evolved allows an attacker to halt the snmpd daemon causing a sustained Denial of Service (DoS) to the service until it is manually restarted. This issue impacts any version of SNMP – v1,v2, v3 This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S20; 15.1 versions prior to 15.1R7-S11; 18.3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S10; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S2, 21.1R3; 21.2 versions prior to 21.2R1-S2, 21.2R2. Juniper Networks Junos OS Evolved 21.2 versions prior to 21.2R3-EVO; 21.3 versions prior to 21.3R2-EVO.

An Improper Access Control vulnerability in Juniper Networks Junos OS Evolved allows a network-based unauthenticated attacker who is able to connect to a specific open IPv4 port, which in affected releases should otherwise be unreachable, to cause the CPU to consume all resources as more traffic is sent to the port to create a Denial of Service (DoS) condition. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS Evolved 20.4 versions prior to 20.4R3-S2-EVO; 21.1 versions prior to 21.1R3-S1-EVO; 21.2 versions prior to 21.2R3-EVO; 21.3 versions prior to 21.3R2-EVO; 21.4 versions prior to 21.4R2-EVO. This issue does not affect Junos OS.

An Incorrect Calculation of Buffer Size vulnerability in Juniper Networks Junos OS SRX 5000 Series devices using SPC2 line cards while ALGs are enabled allows an attacker sending specific crafted packets to cause a transit traffic Denial of Service (DoS). Continued receipt and processing of these specific packets will sustain the Denial of Service condition. This issue affects: Juniper Networks Junos OS SRX 5000 Series with SPC2 with ALGs enabled. * All versions earlier than 21.2R3-S7; * 21.4 versions earlier than 21.4R3-S6; * 22.1 versions earlier than 22.1R3-S5; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S2; * 22.4 versions earlier than 22.4R3; * 23.2 versions earlier than 23.2R2.

A vulnerability in the processing of inbound IPv6 packets in Juniper Networks Junos OS on QFX5000 Series and EX4600 switches may cause the memory to not be freed, leading to a packet DMA memory leak, and eventual Denial of Service (DoS) condition. Once the condition occurs, further packet processing will be impacted, creating a sustained Denial of Service (DoS) condition. The following error logs may be observed using the "show heap" command and the device may eventually run out of memory if such packets are received continuously. Jan 12 12:00:00 device-name fpc0 (buf alloc) failed allocating packet buffer Jan 12 12:00:01 device-name fpc0 (buf alloc) failed allocating packet buffer user@device-name> request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 246fc1a8 536870488 353653752 183216736 34 Kernel 1 91800000 16777216 12069680 4707536 28 DMA 2 92800000 75497472 69997640 5499832 7 PKT DMA DESC 3 106fc000 335544320 221425960 114118360 34 Bcm_sdk 4 97000000 176160768 200 176160568 99 Packet DMA <<<<<<<<<<<<<< 5 903fffe0 20971504 20971504 0 0 Blob This issue affects Juniper Networks Junos OS on QFX5000 Series, EX4600: 18.3R3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S6; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue does not affect Juniper Networks Junos OS: Any versions prior to 17.4R3; 18.1 versions prior to 18.1R3-S6; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R2.

An Uncontrolled Resource Consumption vulnerability in the kernel of Juniper Networks Junos OS allows an unauthenticated network based attacker to cause 100% CPU load and the device to become unresponsive by sending a flood of traffic to the out-of-band management ethernet port. Continued receipted of a flood will create a sustained Denial of Service (DoS) condition. Once the flood subsides the system will recover by itself. An indication that the system is affected by this issue would be that an irq handled by the fman process is shown to be using a high percentage of CPU cycles like in the following example output: user@host> show system processes extensive ... PID USERNAME PRI NICE SIZE RES STATE TIME WCPU COMMAND 31 root -84 -187 0K 16K WAIT 22.2H 56939.26% irq96: fman0 This issue affects Juniper Networks Junos OS: All versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S5; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R2-S2, 20.4R3; 21.1 versions prior to 21.1R2; 21.2 versions prior to 21.2R1-S1, 21.2R2.

An Allocation of Resources Without Limits or Throttling vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS Evolved allows unauthenticated network based attacker to cause a Denial of Service (DoS). On all Junos Evolved platforms hostbound protocols will be impacted by a high rate of specific hostbound traffic from ports on a PFE. Continued receipt of this amount of traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS Evolved: 21.2 versions prior to 21.2R3-EVO; 21.3 versions prior to 21.3R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 21.2R1.

An Access of Uninitialized Pointer vulnerability in the SIP ALG of Juniper Networks Junos OS allows an unauthenticated network-based attacker to cause a Denial of Service (DoS). Continued receipt of these specific packets will cause a sustained Denial of Service condition. On all MX and SRX platforms, if the SIP ALG is enabled, an MS-MPC or MS-MIC, or SPC will crash if it receives a SIP message with a specific contact header format. This issue affects Juniper Networks Junos OS on MX Series and SRX Series: 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R2. This issue does not affect versions prior to 20.4R1.

A Use After Free vulnerability in the Advanced Forwarding Toolkit (AFT) manager process (aftmand) of Juniper Networks Junos OS allows an unauthenticated networked attacker to cause a kernel crash due to intensive polling of Abstracted Fabric (AF) interface statistics and thereby a Denial of Service (DoS). Continued gathering of AF interface statistics will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on MX Series: 20.1 versions later than 20.1R1; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2; 21.2 versions prior to 21.2R2.

An Insufficient Algorithmic Complexity combined with an Allocation of Resources Without Limits or Throttling vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on SRX Series and MX Series with SPC3 allows an unauthenticated network attacker to cause latency in transit packet processing and even packet loss. If transit traffic includes a significant percentage (> 5%) of fragmented packets which need to be reassembled, high latency or packet drops might be observed. This issue affects Juniper Networks Junos OS on SRX Series, MX Series with SPC3: All versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2-S9, 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R1-S1, 19.2R2.

An Improper Locking vulnerability in the SIP ALG of Juniper Networks Junos OS on MX Series and SRX Series allows an unauthenticated networked attacker to cause a flowprocessing daemon (flowd) crash and thereby a Denial of Service (DoS). Continued receipt of these specific packets will cause a sustained Denial of Service condition. This issue can occur in a scenario where the SIP ALG is enabled and specific SIP messages are being processed simultaneously. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series 20.4 versions prior to 20.4R3-S1; 21.1 versions prior to 21.1R2-S2, 21.1R3; 21.2 versions prior to 21.2R1-S2, 21.2R2; 21.3 versions prior to 21.3R1-S1, 21.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1.

On SRX Series devices, an Improper Check for Unusual or Exceptional Conditions when using Certificate Management Protocol Version 2 (CMPv2) auto re-enrollment, allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS) by crashing the pkid process. The pkid process cannot handle an unexpected response from the Certificate Authority (CA) server, leading to crash. A restart is required to restore services. This issue affects: Juniper Networks Junos OS on SRX Series: All versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S1; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R2.

A Buffer Overflow vulnerability in the PFE of Juniper Networks Junos OS on SRX series allows an unauthenticated network based attacker to cause a Denial of Service (DoS). The PFE will crash when specific traffic is scanned by Enhanced Web Filtering safe-search feature of UTM (Unified Threat management). Continued receipt of this specific traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: 20.2 versions prior to 20.2R3-S4 on SRX Series; 20.3 versions prior to 20.3R3-S3 on SRX Series; 20.4 versions prior to 20.4R3-S3 on SRX Series; 21.1 versions prior to 21.1R3-S1 on SRX Series; 21.2 versions prior to 21.2R2-S2, 21.2R3 on SRX Series; 21.3 versions prior to 21.3R2 on SRX Series; 21.4 versions prior to 21.4R2 on SRX Series. This issue does not affect Juniper Networks Junos OS versions prior to 20.2R1.

An Uncontrolled Memory Allocation vulnerability leading to a Heap-based Buffer Overflow in the packet forwarding engine (PFE) of Juniper Networks Junos OS allows a network-based unauthenticated attacker to flood the device with traffic leading to a Denial of Service (DoS). The device must be configured with storm control profiling limiting the number of unknown broadcast, multicast, or unicast traffic to be vulnerable to this issue. This issue affects: Juniper Networks Junos OS on QFX5100/QFX5110/QFX5120/QFX5200/QFX5210/EX4600/EX4650 Series; 20.2 version 20.2R1 and later versions prior to 20.2R2. This issue does not affect: Juniper Networks Junos OS versions prior to 20.2R1.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the processing of specific IPv6 packets on certain EX Series devices may lead to exhaustion of DMA memory causing a Denial of Service (DoS). Over time, exploitation of this vulnerability may cause traffic to stop being forwarded, or a crash of the fxpc process. An indication of the issue occurring may be observed through the following log messages: Sep 13 17:14:59 hostname : %PFE-3: fpc0 (buf alloc) failed allocating packet buffer Sep 13 17:14:59 hostname : %PFE-7: fpc0 brcm_pkt_buf_alloc:393 (buf alloc) failed allocating packet buffer When Packet DMA heap utilization reaches 99%, the system will become unstable. Packet DMA heap utilization can be monitored using the command: user@junos# request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 213301a8 536870488 387228840 149641648 27 Kernel 1 91800000 8388608 3735120 4653488 55 DMA 2 92000000 75497472 74452192 1045280 1 PKT DMA DESC 3 d330000 335544320 257091400 78452920 23 Bcm_sdk 4 96800000 184549376 2408 184546968 99 Packet DMA <<<< 5 903fffe0 20971504 20971504 0 0 Blob This issue affects: Juniper Networks Junos OS 18.4 versions prior to 18.4R2-S10, 18.4R3-S10 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.1 versions prior to 19.1R3-S7 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.3 versions prior to 19.3R3-S5 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.4 versions prior to 19.4R3-S7 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.1 versions prior to 20.1R3-S3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.2 versions prior to 20.2R3-S3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.3 versions prior to 20.3R3-S2 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.4 versions prior to 20.4R3-S1 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.1 versions prior to 21.1R2-S2, 21.1R3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.2 versions prior to 21.2R1-S2, 21.2R2 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.3 versions prior to 21.3R1-S1, 21.3R2 on EX2300 Series, EX2300-MP Series, EX3400 Series.

An Improper Validation of Syntactic Correctness of Input vulnerability in the kernel of Juniper Networks Junos OS Evolved on PTX series allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). When an incoming TCP packet destined to the device is malformed there is a possibility of a kernel panic. Only TCP packets destined to the ports for BGP, LDP and MSDP can trigger this. This issue only affects PTX10004, PTX10008, PTX10016. No other PTX Series devices or other platforms are affected. This issue affects Juniper Networks Junos OS Evolved: 20.4-EVO versions prior to 20.4R3-S4-EVO; 21.3-EVO versions prior to 21.3R3-EVO; 21.4-EVO versions prior to 21.4R3-EVO; 22.1-EVO versions prior to 22.1R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 20.4R1-EVO.

A Missing Release of Memory after Effective Lifetime vulnerability in the kernel of Juniper Networks Junos OS allows an unauthenticated network based attacker to cause a Denial of Service (DoS). On all Junos platforms, the Kernel Routing Table (KRT) queue can get stuck due to a memory leak triggered by interface flaps or route churn leading to RIB and PFEs getting out of sync. The memory leak causes RTNEXTHOP/route and next-hop memory pressure issue and the KRT queue will eventually get stuck with the error- 'ENOMEM -- Cannot allocate memory'. The out-of-sync state between RIB and FIB can be seen with the "show route" and "show route forwarding-table" command. This issue will lead to failures for adding new routes. The KRT queue status can be checked using the CLI command "show krt queue": user@host > show krt state High-priority add queue: 1 queued ADD nhtype Router index 0 (31212) error 'ENOMEM -- Cannot allocate memory' kqp '0x8ad5e40' The following messages will be observed in /var/log/messages, which indicate high memory for routes/nexthops: host rpd[16279]: RPD_RT_HWM_NOTICE: New RIB highwatermark for routes: 266 [2022-03-04 05:06:07] host rpd[16279]: RPD_KRT_Q_RETRIES: nexthop ADD: Cannot allocate memory host rpd[16279]: RPD_KRT_Q_RETRIES: nexthop ADD: Cannot allocate memory host kernel: rts_veto_net_delayed_unref_limit: Route/nexthop memory is severe pressure. User Application to perform recovery actions. O p 8 err 12, rtsm_id 0:-1, msg type 10, veto simulation: 0. host kernel: rts_veto_net_delayed_unref_limit: Memory usage of M_RTNEXTHOP type = (806321208) Max size possible for M_RTNEXTHOP type = (689432176) Current delayed unref = (0), Max delayed unref on this platform = (120000) Current delayed weight unref = (0) Max delayed weight unref on this platform = (400000) curproc = rpd. This issue affects: Juniper Networks Junos OS 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2-S1, 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2; This issue does not affect Juniper Networks Junos OS versions prior to 21.2R1.

An Operation on a Resource after Expiration or Release vulnerability in the Routing Protocol Daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker with an established BGP session to cause a Denial of Service (DoS). This issue occurs when proxy-generate route-target filtering is enabled, and certain proxy-route add and delete events are happening. This issue affects: Juniper Networks Junos OS All versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S8, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S1; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S2, 20.3R2. Juniper Networks Junos OS Evolved All versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R3-EVO; 20.3 versions prior to 20.3R2-EVO.

An Improper Input Validation vulnerability in ingress TCP segment processing of Juniper Networks Junos OS Evolved allows a network-based unauthenticated attacker to send a crafted TCP segment to the device, triggering a kernel panic, leading to a Denial of Service (DoS) condition. Continued receipt and processing of this TCP segment could create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS Evolved: 21.3 versions prior to 21.3R3-EVO; 21.4 versions prior to 21.4R2-EVO; 22.1 versions prior to 22.1R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 21.3R1-EVO.

A Stack-based Buffer Overflow vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on MX Series and SRX series allows an unauthenticated networked attacker to cause a flowd crash and thereby a Denial of Service (DoS). Continued receipt of these specific packets will cause a sustained Denial of Service condition. This issue can be triggered by a specific Session Initiation Protocol (SIP) invite packet if the SIP ALG is enabled. Due to this, the PIC will be rebooted and all traffic that traverses the PIC will be dropped. This issue affects: Juniper Networks Junos OS 20.4 versions prior to 20.4R3-S2; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R2; 21.3 versions prior to 21.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1.

A vulnerability in the NETISR network queue functionality of Juniper Networks Junos OS kernel allows an attacker to cause a Denial of Service (DoS) by sending crafted genuine packets to a device. During an attack, the routing protocol daemon (rpd) CPU may reach 100% utilization, yet FPC CPUs forwarding traffic will operate normally. This attack occurs when the attackers' packets are sent over an IPv4 unicast routing equal-cost multi-path (ECMP) unilist selection. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. An indicator of compromise may be to monitor NETISR drops in the network with the assistance of JTAC. Please contact JTAC for technical support for further guidance. This issue affects: Juniper Networks Junos OS 17.3 version 17.3R3-S9 and later versions prior to 17.3R3-S12; 17.4 version 17.4R3-S3 and later versions prior to 17.4R3-S5; 18.1 version 18.1R3-S11 and later versions prior to 18.1R3-S13; 18.2 version 18.2R3-S6 and later versions; 18.3 version 18.3R3-S4 and later versions prior to 18.3R3-S5; 18.4 version 18.4R3-S5 and later versions prior to 18.4R3-S9; 19.1 version 19.1R3-S3 and later versions prior to 19.1R3-S7. This issue does not affect Juniper Networks Junos OS versions prior to 17.3R3-S9. This issue does not affect Juniper Networks Junos OS Evolved.

On Juniper Networks SRX Series configured with application identification inspection enabled, receipt of specific HTTP traffic can cause high CPU load utilization, which could lead to traffic interruption. Application identification is enabled by default and is automatically turned on when Intrusion Detection and Prevention (IDP), AppFW, AppQoS, or AppTrack is configured. Thus, this issue might occur when IDP, AppFW, AppQoS, or AppTrack is configured. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D105; 15.1X49 versions prior to 15.1X49-D221, 15.1X49-D230; 17.4 versions prior to 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R2-S5, 18.4R3-S1; 19.1 versions prior to 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2.

On Juniper Networks PTX and QFX Series devices with packet sampling configured using tunnel-observation mpls-over-udp, sampling of a malformed packet can cause the Kernel Routing Table (KRT) queue to become stuck. KRT is the module within the Routing Process Daemon (RPD) that synchronized the routing tables with the forwarding tables in the kernel. This table is then synchronized to the Packet Forwarding Engine (PFE) via the KRT queue. Thus, when KRT queue become stuck, it can lead to unexpected packet forwarding issues. An administrator can monitor the following command to check if there is the KRT queue is stuck: user@device > show krt state ... Number of async queue entries: 65007 <--- this value keep on increasing. When this issue occurs, the following message might appear in the /var/log/messages: DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Too many delayed route/nexthop unrefs. Op 2 err 55, rtsm_id 5:-1, msg type 2 DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Memory usage of M_RTNEXTHOP type = (0) Max size possible for M_RTNEXTHOP type = (7297134592) Current delayed unref = (60000), Current unique delayed unref = (18420), Max delayed unref on this platform = (40000) Current delayed weight unref = (60000) Max delayed weight unref on this platform= (400000) curproc = rpd This issue affects Juniper Networks Junos OS on PTX/QFX Series: 17.2X75 versions prior to 17.2X75-D105; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.2X75 versions prior to 18.2X75-D420, 18.2X75-D53, 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R1-S7, 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2. This issue does not affect Juniper Networks Junos OS prior to 18.1R1.

On Juniper Networks Junos OS devices, receipt of a malformed IPv6 packet may cause the system to crash and restart (vmcore). This issue can be trigged by a malformed IPv6 packet destined to the Routing Engine. An attacker can repeatedly send the offending packet resulting in an extended Denial of Service condition. Only IPv6 packets can trigger this issue. IPv4 packets cannot trigger this issue. This issue affects Juniper Networks Junos OS 18.4 versions prior to 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2. This issue does not affect Juniper Networks Junos OS prior to 18.4R1.

On Juniper Networks Junos OS platforms configured as DHCPv6 local server or DHCPv6 Relay Agent, Juniper Networks Dynamic Host Configuration Protocol Daemon (JDHCPD) process might crash with a core dump if a malformed DHCPv6 packet is received, resulting with the restart of the daemon. This issue only affects DHCPv6, it does not affect DHCPv4. This issue affects: Juniper Networks Junos OS 17.4 versions prior to 17.4R2-S12, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.2X75 versions prior to 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.2 version 19.2R2 and later versions; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2; This issue does not affect Juniper Networks Junos OS prior to 17.4R1.

On Juniper Networks Junos OS devices configured with DHCPv6 relay enabled, receipt of a specific DHCPv6 packet might crash the jdhcpd daemon. The jdhcpd daemon automatically restarts without intervention, but continuous receipt of specific crafted DHCP messages will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. Only DHCPv6 packet can trigger this issue. DHCPv4 packet cannot trigger this issue. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R2-S1, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2.

On Juniper Networks Junos OS devices, a specific SNMP OID poll causes a memory leak which over time leads to a kernel crash (vmcore). Prior to the kernel crash other processes might be impacted, such as failure to establish SSH connection to the device. The administrator can monitor the output of the following command to check if there is memory leak caused by this issue: user@device> show system virtual-memory | match "pfe_ipc|kmem" pfe_ipc 147 5K - 164352 16,32,64,8192 <-- increasing vm.kmem_map_free: 127246336 <-- decreasing pfe_ipc 0 0K - 18598 32,8192 vm.kmem_map_free: 134582272 This issue affects Juniper Networks Junos OS: 17.4R3; 18.1 version 18.1R3-S5 and later versions prior to 18.1R3-S10; 18.2 version 18.2R3 and later versions prior to 18.2R3-S3; 18.2X75 version 18.2X75-D420, 18.2X75-D50 and later versions prior to 18.2X75-D430, 18.2X75-D53, 18.2X75-D60; 18.3 version 18.3R3 and later versions prior to 18.3R3-S2; 18.4 version 18.4R1-S4, 18.4R2 and later versions prior to 18.4R2-S5, 18.4R3-S1; 19.1 version 19.1R2 and later versions prior to 19.1R2-S2, 19.1R3; 19.2 version 19.2R1 and later versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S5, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2. This issue does not affect Juniper Networks Junos OS prior to 17.4R3.

On Juniper Networks Junos OS and Junos OS Evolved devices, BGP session flapping can lead to a routing process daemon (RPD) crash and restart, limiting the attack surface to configured BGP peers. This issue only affects devices with BGP damping in combination with accepted-prefix-limit configuration. When the issue occurs the following messages will appear in the /var/log/messages: rpd[6046]: %DAEMON-4-BGP_PREFIX_THRESH_EXCEEDED: XXXX (External AS x): Configured maximum accepted prefix-limit threshold(1800) exceeded for inet6-unicast nlri: 1984 (instance master) rpd[6046]: %DAEMON-3-BGP_CEASE_PREFIX_LIMIT_EXCEEDED: 2001:x:x:x::2 (External AS x): Shutting down peer due to exceeding configured maximum accepted prefix-limit(2000) for inet6-unicast nlri: 2001 (instance master) rpd[6046]: %DAEMON-4: bgp_rt_maxprefixes_check_common:9284: NOTIFICATION sent to 2001:x:x:x::2 (External AS x): code 6 (Cease) subcode 1 (Maximum Number of Prefixes Reached) AFI: 2 SAFI: 1 prefix limit 2000 kernel: %KERN-5: mastership_relinquish_on_process_exit: RPD crashed on master RE. Sending SIGUSR2 to chassisd (5612:chassisd) to trigger RE switchover This issue affects: Juniper Networks Junos OS: 17.2R3-S3; 17.3 version 17.3R3-S3 and later versions, prior to 17.3R3-S8; 17.4 version 17.4R2-S4, 17.4R3 and later versions, prior to 17.4R2-S10, 17.4R3-S2; 18.1 version 18.1R3-S6 and later versions, prior to 18.1R3-S10; 18.2 version 18.2R3 and later versions, prior to 18.2R3-S4; 18.2X75 version 18.2X75-D50, 18.2X75-D60 and later versions, prior to 18.2X75-D53, 18.2X75-D65; 18.3 version 18.3R2 and later versions, prior to 18.3R2-S4, 18.3R3-S2; 18.4 version 18.4R2 and later versions, prior to 18.4R2-S5, 18.4R3-S2; 19.1 version 19.1R1 and later versions, prior to 19.1R2-S2, 19.1R3-S1; 19.2 version 19.2R1 and later versions, prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2; 20.1 versions prior to 20.1R1-S2, 20.1R2. Juniper Networks Junos OS Evolved prior to 20.1R2-EVO. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R3-S3.

A vulnerability in the BGP FlowSpec implementation may cause a Juniper Networks Junos OS device to terminate an established BGP session upon receiving a specific BGP FlowSpec advertisement. The BGP NOTIFICATION message that terminates an established BGP session is sent toward the peer device that originally sent the specific BGP FlowSpec advertisement. This specific BGP FlowSpec advertisement received from a BGP peer might get propagated from a Junos OS device running the fixed release to another device that is vulnerable causing BGP session termination downstream. This issue affects IPv4 and IPv6 BGP FlowSpec deployment. This issue affects Juniper Networks Junos OS: 12.3; 12.3X48 on SRX Series; 14.1X53 on EX and QFX Series; 15.1 versions prior to 15.1R7-S5; 15.1F versions prior to 15.1F6-S13; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D497 on NFX Series; 15.1X53 versions prior to 15.1X53-D592 on EX2300/EX3400; 16.1 versions prior to 16.1R7-S7; 17.1 versions prior to 17.1R2-S12, 17.1R3; 17.2 versions prior to 17.2R2-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D102, 17.2X75-D110, 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions prior to 17.4R1-S8, 17.4R2; 18.1 versions prior to 18.1R2-S4, 18.1R3; 18.2X75 versions prior to 18.2X75-D20.

When an attacker sends a specific crafted Ethernet Operation, Administration, and Maintenance (Ethernet OAM) packet to a target device, it may improperly handle the incoming malformed data and fail to sanitize this incoming data resulting in an overflow condition. This overflow condition in Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) condition by coring the CFM daemon. Continued receipt of these packets may cause an extended Denial of Service condition. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D95 on SRX Series; 14.1X50 versions prior to 14.1X50-D145; 14.1X53 versions prior to 14.1X53-D47; 15.1 versions prior to 15.1R2; 15.1X49 versions prior to 15.1X49-D170 on SRX Series; 15.1X53 versions prior to 15.1X53-D67.