In the Linux kernel, the following vulnerability has been resolved: firmware: cs_dsp: Return error if block header overflows file Return an error from cs_dsp_power_up() if a block header is longer than the amount of data left in the file. The previous code in cs_dsp_load() and cs_dsp_load_coeff() would loop while there was enough data left in the file for a valid region. This protected against overrunning the end of the file data, but it didn't abort the file processing with an error.

A buffer overflow vulnerability was found in the Linux kernel Intel’s iSMT SMBus host controller driver in the way it handled the I2C_SMBUS_BLOCK_PROC_CALL case (via the ioctl I2C_SMBUS) with malicious input data. This flaw could allow a local user to crash the system.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: configfs: Prevent OOB read/write in usb_string_copy() Userspace provided string 's' could trivially have the length zero. Left unchecked this will firstly result in an OOB read in the form `if (str[0 - 1] == '\n') followed closely by an OOB write in the form `str[0 - 1] = '\0'`. There is already a validating check to catch strings that are too long. Let's supply an additional check for invalid strings that are too short.

In the Linux kernel, the following vulnerability has been resolved: mm: cachestat: fix two shmem bugs When cachestat on shmem races with swapping and invalidation, there are two possible bugs: 1) A swapin error can have resulted in a poisoned swap entry in the shmem inode's xarray. Calling get_shadow_from_swap_cache() on it will result in an out-of-bounds access to swapper_spaces[]. Validate the entry with non_swap_entry() before going further. 2) When we find a valid swap entry in the shmem's inode, the shadow entry in the swapcache might not exist yet: swap IO is still in progress and we're before __remove_mapping; swapin, invalidation, or swapoff have removed the shadow from swapcache after we saw the shmem swap entry. This will send a NULL to workingset_test_recent(). The latter purely operates on pointer bits, so it won't crash - node 0, memcg ID 0, eviction timestamp 0, etc. are all valid inputs - but it's a bogus test. In theory that could result in a false "recently evicted" count. Such a false positive wouldn't be the end of the world. But for code clarity and (future) robustness, be explicit about this case. Bail on get_shadow_from_swap_cache() returning NULL.

A vulnerability was found in the Linux kernel's nft_set_desc_concat_parse() function .This flaw allows an attacker to trigger a buffer overflow via nft_set_desc_concat_parse() , causing a denial of service and possibly to run code.

The Linux kernel was found vulnerable out of bounds memory access in the drivers/video/fbdev/sm712fb.c:smtcfb_read() function. The vulnerability could result in local attackers being able to crash the kernel.

In the Linux kernel, the following vulnerability has been resolved: module: Fix kernel panic when a symbol st_shndx is out of bounds The module loader doesn't check for bounds of the ELF section index in simplify_symbols(): for (i = 1; i < symsec->sh_size / sizeof(Elf_Sym); i++) { const char *name = info->strtab + sym[i].st_name; switch (sym[i].st_shndx) { case SHN_COMMON: [...] default: /* Divert to percpu allocation if a percpu var. */ if (sym[i].st_shndx == info->index.pcpu) secbase = (unsigned long)mod_percpu(mod); else /** HERE --> **/ secbase = info->sechdrs[sym[i].st_shndx].sh_addr; sym[i].st_value += secbase; break; } } A symbol with an out-of-bounds st_shndx value, for example 0xffff (known as SHN_XINDEX or SHN_HIRESERVE), may cause a kernel panic: BUG: unable to handle page fault for address: ... RIP: 0010:simplify_symbols+0x2b2/0x480 ... Kernel panic - not syncing: Fatal exception This can happen when module ELF is legitimately using SHN_XINDEX or when it is corrupted. Add a bounds check in simplify_symbols() to validate that st_shndx is within the valid range before using it. This issue was discovered due to a bug in llvm-objcopy, see relevant discussion for details [1]. [1] https://lore.kernel.org/linux-modules/20251224005752.201911-1-ihor.solodrai@linux.dev/

In the Linux kernel, the following vulnerability has been resolved: net: usb: cdc-phonet: fix skb frags[] overflow in rx_complete() A malicious USB device claiming to be a CDC Phonet modem can overflow the skb_shared_info->frags[] array by sending an unbounded sequence of full-page bulk transfers. Drop the skb and increment the length error when the frag limit is reached. This matches the same fix that commit f0813bcd2d9d ("net: wwan: t7xx: fix potential skb->frags overflow in RX path") did for the t7xx driver.

A heap-based buffer overflow in the vrend_renderer_transfer_write_iov function in vrend_renderer.c in virglrenderer through 0.8.0 allows guest OS users to cause a denial of service via VIRGL_CCMD_RESOURCE_INLINE_WRITE commands.

zsh through version 5.4.2 is vulnerable to a stack-based buffer overflow in the exec.c:hashcmd() function. A local attacker could exploit this to cause a denial of service.

In the Linux kernel, the following vulnerability has been resolved: x86/fpu: KVM: Set the base guest FPU uABI size to sizeof(struct kvm_xsave) Set the starting uABI size of KVM's guest FPU to 'struct kvm_xsave', i.e. to KVM's historical uABI size. When saving FPU state for usersapce, KVM (well, now the FPU) sets the FP+SSE bits in the XSAVE header even if the host doesn't support XSAVE. Setting the XSAVE header allows the VM to be migrated to a host that does support XSAVE without the new host having to handle FPU state that may or may not be compatible with XSAVE. Setting the uABI size to the host's default size results in out-of-bounds writes (setting the FP+SSE bits) and data corruption (that is thankfully caught by KASAN) when running on hosts without XSAVE, e.g. on Core2 CPUs. WARN if the default size is larger than KVM's historical uABI size; all features that can push the FPU size beyond the historical size must be opt-in. ================================================================== BUG: KASAN: slab-out-of-bounds in fpu_copy_uabi_to_guest_fpstate+0x86/0x130 Read of size 8 at addr ffff888011e33a00 by task qemu-build/681 CPU: 1 PID: 681 Comm: qemu-build Not tainted 5.18.0-rc5-KASAN-amd64 #1 Hardware name: /DG35EC, BIOS ECG3510M.86A.0118.2010.0113.1426 01/13/2010 Call Trace: <TASK> dump_stack_lvl+0x34/0x45 print_report.cold+0x45/0x575 kasan_report+0x9b/0xd0 fpu_copy_uabi_to_guest_fpstate+0x86/0x130 kvm_arch_vcpu_ioctl+0x72a/0x1c50 [kvm] kvm_vcpu_ioctl+0x47f/0x7b0 [kvm] __x64_sys_ioctl+0x5de/0xc90 do_syscall_64+0x31/0x50 entry_SYSCALL_64_after_hwframe+0x44/0xae </TASK> Allocated by task 0: (stack is not available) The buggy address belongs to the object at ffff888011e33800 which belongs to the cache kmalloc-512 of size 512 The buggy address is located 0 bytes to the right of 512-byte region [ffff888011e33800, ffff888011e33a00) The buggy address belongs to the physical page: page:0000000089cd4adb refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x11e30 head:0000000089cd4adb order:2 compound_mapcount:0 compound_pincount:0 flags: 0x4000000000010200(slab|head|zone=1) raw: 4000000000010200 dead000000000100 dead000000000122 ffff888001041c80 raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888011e33900: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888011e33980: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff888011e33a00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff888011e33a80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888011e33b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ================================================================== Disabling lock debugging due to kernel taint

In the Linux kernel, the following vulnerability has been resolved: vmxnet3: Fix packet corruption in vmxnet3_xdp_xmit_frame Andrew and Nikolay reported connectivity issues with Cilium's service load-balancing in case of vmxnet3. If a BPF program for native XDP adds an encapsulation header such as IPIP and transmits the packet out the same interface, then in case of vmxnet3 a corrupted packet is being sent and subsequently dropped on the path. vmxnet3_xdp_xmit_frame() which is called e.g. via vmxnet3_run_xdp() through vmxnet3_xdp_xmit_back() calculates an incorrect DMA address: page = virt_to_page(xdpf->data); tbi->dma_addr = page_pool_get_dma_addr(page) + VMXNET3_XDP_HEADROOM; dma_sync_single_for_device(&adapter->pdev->dev, tbi->dma_addr, buf_size, DMA_TO_DEVICE); The above assumes a fixed offset (VMXNET3_XDP_HEADROOM), but the XDP BPF program could have moved xdp->data. While the passed buf_size is correct (xdpf->len), the dma_addr needs to have a dynamic offset which can be calculated as xdpf->data - (void *)xdpf, that is, xdp->data - xdp->data_hard_start.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_core: Fix not checking skb length on hci_acldata_packet This fixes not checking if skb really contains an ACL header otherwise the code may attempt to access some uninitilized/invalid memory past the valid skb->data.

In the Linux kernel, the following vulnerability has been resolved: iio: adc: ad7923: Fix buffer overflow for tx_buf and ring_xfer The AD7923 was updated to support devices with 8 channels, but the size of tx_buf and ring_xfer was not increased accordingly, leading to a potential buffer overflow in ad7923_update_scan_mode().

In the Linux kernel, the following vulnerability has been resolved: nvmet: Don't overflow subsysnqn nvmet_root_discovery_nqn_store treats the subsysnqn string like a fixed size buffer, even though it is dynamically allocated to the size of the string. Create a new string with kstrndup instead of using the old buffer.

In the Linux kernel, the following vulnerability has been resolved: clk: clk-loongson2: Fix potential buffer overflow in flexible-array member access Flexible-array member `hws` in `struct clk_hw_onecell_data` is annotated with the `counted_by()` attribute. This means that when memory is allocated for this array, the _counter_, which in this case is member `num` in the flexible structure, should be set to the maximum number of elements the flexible array can contain, or fewer. In this case, the total number of elements for the flexible array is determined by variable `clks_num` when allocating heap space via `devm_kzalloc()`, as shown below: 289 struct loongson2_clk_provider *clp; ... 296 for (p = data; p->name; p++) 297 clks_num++; 298 299 clp = devm_kzalloc(dev, struct_size(clp, clk_data.hws, clks_num), 300 GFP_KERNEL); So, `clp->clk_data.num` should be set to `clks_num` or less, and not exceed `clks_num`, as is currently the case. Otherwise, if data is written into `clp->clk_data.hws[clks_num]`, the instrumentation provided by the compiler won't detect the overflow, leading to a memory corruption bug at runtime. Fix this issue by setting `clp->clk_data.num` to `clks_num`.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: mtk_eth_soc: fix memory corruption during fq dma init The loop responsible for allocating up to MTK_FQ_DMA_LENGTH buffers must only touch as many descriptors, otherwise it ends up corrupting unrelated memory. Fix the loop iteration count accordingly.

In the Linux kernel, the following vulnerability has been resolved: media: vivid: fix buffer overwrite when using > 32 buffers The maximum number of buffers that can be requested was increased to 64 for the video capture queue. But video capture used a must_blank array that was still sized for 32 (VIDEO_MAX_FRAME). This caused an out-of-bounds write when using buffer indices >= 32. Create a new define MAX_VID_CAP_BUFFERS that is used to access the must_blank array and set max_num_buffers for the video capture queue. This solves a crash reported by: https://bugzilla.kernel.org/show_bug.cgi?id=219258

In the Linux kernel, the following vulnerability has been resolved: drm/xe/oa: Fix overflow in oa batch buffer By default xe_bb_create_job() appends a MI_BATCH_BUFFER_END to batch buffer, this is not a problem if batch buffer is only used once but oa reuses the batch buffer for the same metric and at each call it appends a MI_BATCH_BUFFER_END, printing the warning below and then overflowing. [ 381.072016] ------------[ cut here ]------------ [ 381.072019] xe 0000:00:02.0: [drm] Assertion `bb->len * 4 + bb_prefetch(q->gt) <= size` failed! platform: LUNARLAKE subplatform: 1 graphics: Xe2_LPG / Xe2_HPG 20.04 step B0 media: Xe2_LPM / Xe2_HPM 20.00 step B0 tile: 0 VRAM 0 B GT: 0 type 1 So here checking if batch buffer already have MI_BATCH_BUFFER_END if not append it. v2: - simply fix, suggestion from Ashutosh (cherry picked from commit 9ba0e0f30ca42a98af3689460063edfb6315718a)

In the Linux kernel, the following vulnerability has been resolved: MIPS: ftrace: Fix memory corruption when kernel is located beyond 32 bits Since commit e424054000878 ("MIPS: Tracing: Reduce the overhead of dynamic Function Tracer"), the macro UASM_i_LA_mostly has been used, and this macro can generate more than 2 instructions. At the same time, the code in ftrace assumes that no more than 2 instructions can be generated, which is why it stores them in an int[2] array. However, as previously noted, the macro UASM_i_LA_mostly (and now UASM_i_LA) causes a buffer overflow when _mcount is beyond 32 bits. This leads to corruption of the variables located in the __read_mostly section. This corruption was observed because the variable __cpu_primary_thread_mask was corrupted, causing a hang very early during boot. This fix prevents the corruption by avoiding the generation of instructions if they could exceed 2 instructions in length. Fortunately, insn_la_mcount is only used if the instrumented code is located outside the kernel code section, so dynamic ftrace can still be used, albeit in a more limited scope. This is still preferable to corrupting memory and/or crashing the kernel.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7996: use hweight16 to get correct tx antenna The chainmask is u16 so using hweight8 cannot get correct tx_ant. Without this patch, the tx_ant of band 2 would be -1 and lead to the following issue: BUG: KASAN: stack-out-of-bounds in mt7996_mcu_add_sta+0x12e0/0x16e0 [mt7996e]

In the Linux kernel, the following vulnerability has been resolved: erofs: fix out-of-bound access when z_erofs_gbuf_growsize() partially fails If z_erofs_gbuf_growsize() partially fails on a global buffer due to memory allocation failure or fault injection (as reported by syzbot [1]), new pages need to be freed by comparing to the existing pages to avoid memory leaks. However, the old gbuf->pages[] array may not be large enough, which can lead to null-ptr-deref or out-of-bound access. Fix this by checking against gbuf->nrpages in advance. [1] https://lore.kernel.org/r/000000000000f7b96e062018c6e3@google.com

In the Linux kernel, the following vulnerability has been resolved: soc: qcom: cmd-db: Map shared memory as WC, not WB Linux does not write into cmd-db region. This region of memory is write protected by XPU. XPU may sometime falsely detect clean cache eviction as "write" into the write protected region leading to secure interrupt which causes an endless loop somewhere in Trust Zone. The only reason it is working right now is because Qualcomm Hypervisor maps the same region as Non-Cacheable memory in Stage 2 translation tables. The issue manifests if we want to use another hypervisor (like Xen or KVM), which does not know anything about those specific mappings. Changing the mapping of cmd-db memory from MEMREMAP_WB to MEMREMAP_WT/WC removes dependency on correct mappings in Stage 2 tables. This patch fixes the issue by updating the mapping to MEMREMAP_WC. I tested this on SA8155P with Xen.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix a kernel verifier crash in stacksafe() Daniel Hodges reported a kernel verifier crash when playing with sched-ext. Further investigation shows that the crash is due to invalid memory access in stacksafe(). More specifically, it is the following code: if (exact != NOT_EXACT && old->stack[spi].slot_type[i % BPF_REG_SIZE] != cur->stack[spi].slot_type[i % BPF_REG_SIZE]) return false; The 'i' iterates old->allocated_stack. If cur->allocated_stack < old->allocated_stack the out-of-bound access will happen. To fix the issue add 'i >= cur->allocated_stack' check such that if the condition is true, stacksafe() should fail. Otherwise, cur->stack[spi].slot_type[i % BPF_REG_SIZE] memory access is legal.

In the Linux kernel, the following vulnerability has been resolved: igb: cope with large MAX_SKB_FRAGS Sabrina reports that the igb driver does not cope well with large MAX_SKB_FRAG values: setting MAX_SKB_FRAG to 45 causes payload corruption on TX. An easy reproducer is to run ssh to connect to the machine. With MAX_SKB_FRAGS=17 it works, with MAX_SKB_FRAGS=45 it fails. This has been reported originally in https://bugzilla.redhat.com/show_bug.cgi?id=2265320 The root cause of the issue is that the driver does not take into account properly the (possibly large) shared info size when selecting the ring layout, and will try to fit two packets inside the same 4K page even when the 1st fraglist will trump over the 2nd head. Address the issue by checking if 2K buffers are insufficient.

In the Linux kernel, the following vulnerability has been resolved: mm/vmalloc: fix page mapping if vm_area_alloc_pages() with high order fallback to order 0 The __vmap_pages_range_noflush() assumes its argument pages** contains pages with the same page shift. However, since commit e9c3cda4d86e ("mm, vmalloc: fix high order __GFP_NOFAIL allocations"), if gfp_flags includes __GFP_NOFAIL with high order in vm_area_alloc_pages() and page allocation failed for high order, the pages** may contain two different page shifts (high order and order-0). This could lead __vmap_pages_range_noflush() to perform incorrect mappings, potentially resulting in memory corruption. Users might encounter this as follows (vmap_allow_huge = true, 2M is for PMD_SIZE): kvmalloc(2M, __GFP_NOFAIL|GFP_X) __vmalloc_node_range_noprof(vm_flags=VM_ALLOW_HUGE_VMAP) vm_area_alloc_pages(order=9) ---> order-9 allocation failed and fallback to order-0 vmap_pages_range() vmap_pages_range_noflush() __vmap_pages_range_noflush(page_shift = 21) ----> wrong mapping happens We can remove the fallback code because if a high-order allocation fails, __vmalloc_node_range_noprof() will retry with order-0. Therefore, it is unnecessary to fallback to order-0 here. Therefore, fix this by removing the fallback code.

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Fix for possible memory corruption Init Control Block is dereferenced incorrectly. Correctly dereference ICB

In the Linux kernel, the following vulnerability has been resolved: RDMA/restrack: Fix potential invalid address access struct rdma_restrack_entry's kern_name was set to KBUILD_MODNAME in ib_create_cq(), while if the module exited but forgot del this rdma_restrack_entry, it would cause a invalid address access in rdma_restrack_clean() when print the owner of this rdma_restrack_entry. These code is used to help find one forgotten PD release in one of the ULPs. But it is not needed anymore, so delete them.

In the Linux kernel, the following vulnerability has been resolved: parisc: Fix random data corruption from exception handler The current exception handler implementation, which assists when accessing user space memory, may exhibit random data corruption if the compiler decides to use a different register than the specified register %r29 (defined in ASM_EXCEPTIONTABLE_REG) for the error code. If the compiler choose another register, the fault handler will nevertheless store -EFAULT into %r29 and thus trash whatever this register is used for. Looking at the assembly I found that this happens sometimes in emulate_ldd(). To solve the issue, the easiest solution would be if it somehow is possible to tell the fault handler which register is used to hold the error code. Using %0 or %1 in the inline assembly is not posssible as it will show up as e.g. %r29 (with the "%r" prefix), which the GNU assembler can not convert to an integer. This patch takes another, better and more flexible approach: We extend the __ex_table (which is out of the execution path) by one 32-word. In this word we tell the compiler to insert the assembler instruction "or %r0,%r0,%reg", where %reg references the register which the compiler choosed for the error return code. In case of an access failure, the fault handler finds the __ex_table entry and can examine the opcode. The used register is encoded in the lowest 5 bits, and the fault handler can then store -EFAULT into this register. Since we extend the __ex_table to 3 words we can't use the BUILDTIME_TABLE_SORT config option any longer.

In the Linux kernel, the following vulnerability has been resolved: firmware: cs_dsp: Prevent buffer overrun when processing V2 alg headers Check that all fields of a V2 algorithm header fit into the available firmware data buffer. The wmfw V2 format introduced variable-length strings in the algorithm block header. This means the overall header length is variable, and the position of most fields varies depending on the length of the string fields. Each field must be checked to ensure that it does not overflow the firmware data buffer. As this ia bugfix patch, the fixes avoid making any significant change to the existing code. This makes it easier to review and less likely to introduce new bugs.

In the Linux kernel, the following vulnerability has been resolved: iio: adc: ad7124: Fix potential overflow due to non sequential channel numbers Channel numbering must start at 0 and then not have any holes, or it is possible to overflow the available storage. Note this bug was introduced as part of a fix to ensure we didn't rely on the ordering of child nodes. So we need to support arbitrary ordering but they all need to be there somewhere. Note I hit this when using qemu to test the rest of this series. Arguably this isn't the best fix, but it is probably the most minimal option for backporting etc. Alexandru's sign-off is here because he carried this patch in a larger set that Jonathan then applied.

In the Linux kernel, the following vulnerability has been resolved: mm/swap: fix race when skipping swapcache When skipping swapcache for SWP_SYNCHRONOUS_IO, if two or more threads swapin the same entry at the same time, they get different pages (A, B). Before one thread (T0) finishes the swapin and installs page (A) to the PTE, another thread (T1) could finish swapin of page (B), swap_free the entry, then swap out the possibly modified page reusing the same entry. It breaks the pte_same check in (T0) because PTE value is unchanged, causing ABA problem. Thread (T0) will install a stalled page (A) into the PTE and cause data corruption. One possible callstack is like this: CPU0 CPU1 ---- ---- do_swap_page() do_swap_page() with same entry <direct swapin path> <direct swapin path> <alloc page A> <alloc page B> swap_read_folio() <- read to page A swap_read_folio() <- read to page B <slow on later locks or interrupt> <finished swapin first> ... set_pte_at() swap_free() <- entry is free <write to page B, now page A stalled> <swap out page B to same swap entry> pte_same() <- Check pass, PTE seems unchanged, but page A is stalled! swap_free() <- page B content lost! set_pte_at() <- staled page A installed! And besides, for ZRAM, swap_free() allows the swap device to discard the entry content, so even if page (B) is not modified, if swap_read_folio() on CPU0 happens later than swap_free() on CPU1, it may also cause data loss. To fix this, reuse swapcache_prepare which will pin the swap entry using the cache flag, and allow only one thread to swap it in, also prevent any parallel code from putting the entry in the cache. Release the pin after PT unlocked. Racers just loop and wait since it's a rare and very short event. A schedule_timeout_uninterruptible(1) call is added to avoid repeated page faults wasting too much CPU, causing livelock or adding too much noise to perf statistics. A similar livelock issue was described in commit 029c4628b2eb ("mm: swap: get rid of livelock in swapin readahead") Reproducer: This race issue can be triggered easily using a well constructed reproducer and patched brd (with a delay in read path) [1]: With latest 6.8 mainline, race caused data loss can be observed easily: $ gcc -g -lpthread test-thread-swap-race.c && ./a.out Polulating 32MB of memory region... Keep swapping out... Starting round 0... Spawning 65536 workers... 32746 workers spawned, wait for done... Round 0: Error on 0x5aa00, expected 32746, got 32743, 3 data loss! Round 0: Error on 0x395200, expected 32746, got 32743, 3 data loss! Round 0: Error on 0x3fd000, expected 32746, got 32737, 9 data loss! Round 0 Failed, 15 data loss! This reproducer spawns multiple threads sharing the same memory region using a small swap device. Every two threads updates mapped pages one by one in opposite direction trying to create a race, with one dedicated thread keep swapping out the data out using madvise. The reproducer created a reproduce rate of about once every 5 minutes, so the race should be totally possible in production. After this patch, I ran the reproducer for over a few hundred rounds and no data loss observed. Performance overhead is minimal, microbenchmark swapin 10G from 32G zram: Before: 10934698 us After: 11157121 us Cached: 13155355 us (Dropping SWP_SYNCHRONOUS_IO flag) [kasong@tencent.com: v4]

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix list_add() corruption in lpfc_drain_txq() When parsing the txq list in lpfc_drain_txq(), the driver attempts to pass the requests to the adapter. If such an attempt fails, a local "fail_msg" string is set and a log message output. The job is then added to a completions list for cancellation. Processing of any further jobs from the txq list continues, but since "fail_msg" remains set, jobs are added to the completions list regardless of whether a wqe was passed to the adapter. If successfully added to txcmplq, jobs are added to both lists resulting in list corruption. Fix by clearing the fail_msg string after adding a job to the completions list. This stops the subsequent jobs from being added to the completions list unless they had an appropriate failure.

In the Linux kernel, the following vulnerability has been resolved: NFS: fix an incorrect limit in filelayout_decode_layout() The "sizeof(struct nfs_fh)" is two bytes too large and could lead to memory corruption. It should be NFS_MAXFHSIZE because that's the size of the ->data[] buffer. I reversed the size of the arguments to put the variable on the left.

In the Linux kernel, the following vulnerability has been resolved: NFS: Don't corrupt the value of pg_bytes_written in nfs_do_recoalesce() The value of mirror->pg_bytes_written should only be updated after a successful attempt to flush out the requests on the list.

In the Linux kernel, the following vulnerability has been resolved: ubifs: Fix races between xattr_{set|get} and listxattr operations UBIFS may occur some problems with concurrent xattr_{set|get} and listxattr operations, such as assertion failure, memory corruption, stale xattr value[1]. Fix it by importing a new rw-lock in @ubifs_inode to serilize write operations on xattr, concurrent read operations are still effective, just like ext4. [1] https://lore.kernel.org/linux-mtd/20200630130438.141649-1-houtao1@huawei.com

In the Linux kernel, the following vulnerability has been resolved: afs: Fix corruption in reads at fpos 2G-4G from an OpenAFS server AFS-3 has two data fetch RPC variants, FS.FetchData and FS.FetchData64, and Linux's afs client switches between them when talking to a non-YFS server if the read size, the file position or the sum of the two have the upper 32 bits set of the 64-bit value. This is a problem, however, since the file position and length fields of FS.FetchData are *signed* 32-bit values. Fix this by capturing the capability bits obtained from the fileserver when it's sent an FS.GetCapabilities RPC, rather than just discarding them, and then picking out the VICED_CAPABILITY_64BITFILES flag. This can then be used to decide whether to use FS.FetchData or FS.FetchData64 - and also FS.StoreData or FS.StoreData64 - rather than using upper_32_bits() to switch on the parameter values. This capabilities flag could also be used to limit the maximum size of the file, but all servers must be checked for that. Note that the issue does not exist with FS.StoreData - that uses *unsigned* 32-bit values. It's also not a problem with Auristor servers as its YFS.FetchData64 op uses unsigned 64-bit values. This can be tested by cloning a git repo through an OpenAFS client to an OpenAFS server and then doing "git status" on it from a Linux afs client[1]. Provided the clone has a pack file that's in the 2G-4G range, the git status will show errors like: error: packfile .git/objects/pack/pack-5e813c51d12b6847bbc0fcd97c2bca66da50079c.pack does not match index error: packfile .git/objects/pack/pack-5e813c51d12b6847bbc0fcd97c2bca66da50079c.pack does not match index This can be observed in the server's FileLog with something like the following appearing: Sun Aug 29 19:31:39 2021 SRXAFS_FetchData, Fid = 2303380852.491776.3263114, Host 192.168.11.201:7001, Id 1001 Sun Aug 29 19:31:39 2021 CheckRights: len=0, for host=192.168.11.201:7001 Sun Aug 29 19:31:39 2021 FetchData_RXStyle: Pos 18446744071815340032, Len 3154 Sun Aug 29 19:31:39 2021 FetchData_RXStyle: file size 2400758866 ... Sun Aug 29 19:31:40 2021 SRXAFS_FetchData returns 5 Note the file position of 18446744071815340032. This is the requested file position sign-extended.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Wrap the tx reporter dump callback to extract the sq Function mlx5e_tx_reporter_dump_sq() casts its void * argument to struct mlx5e_txqsq *, but in TX-timeout-recovery flow the argument is actually of type struct mlx5e_tx_timeout_ctx *. mlx5_core 0000:08:00.1 enp8s0f1: TX timeout detected mlx5_core 0000:08:00.1 enp8s0f1: TX timeout on queue: 1, SQ: 0x11ec, CQ: 0x146d, SQ Cons: 0x0 SQ Prod: 0x1, usecs since last trans: 21565000 BUG: stack guard page was hit at 0000000093f1a2de (stack is 00000000b66ea0dc..000000004d932dae) kernel stack overflow (page fault): 0000 [#1] SMP NOPTI CPU: 5 PID: 95 Comm: kworker/u20:1 Tainted: G W OE 5.13.0_mlnx #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Workqueue: mlx5e mlx5e_tx_timeout_work [mlx5_core] RIP: 0010:mlx5e_tx_reporter_dump_sq+0xd3/0x180 [mlx5_core] Call Trace: mlx5e_tx_reporter_dump+0x43/0x1c0 [mlx5_core] devlink_health_do_dump.part.91+0x71/0xd0 devlink_health_report+0x157/0x1b0 mlx5e_reporter_tx_timeout+0xb9/0xf0 [mlx5_core] ? mlx5e_tx_reporter_err_cqe_recover+0x1d0/0x1d0 [mlx5_core] ? mlx5e_health_queue_dump+0xd0/0xd0 [mlx5_core] ? update_load_avg+0x19b/0x550 ? set_next_entity+0x72/0x80 ? pick_next_task_fair+0x227/0x340 ? finish_task_switch+0xa2/0x280 mlx5e_tx_timeout_work+0x83/0xb0 [mlx5_core] process_one_work+0x1de/0x3a0 worker_thread+0x2d/0x3c0 ? process_one_work+0x3a0/0x3a0 kthread+0x115/0x130 ? kthread_park+0x90/0x90 ret_from_fork+0x1f/0x30 --[ end trace 51ccabea504edaff ]--- RIP: 0010:mlx5e_tx_reporter_dump_sq+0xd3/0x180 PKRU: 55555554 Kernel panic - not syncing: Fatal exception Kernel Offset: disabled end Kernel panic - not syncing: Fatal exception To fix this bug add a wrapper for mlx5e_tx_reporter_dump_sq() which extracts the sq from struct mlx5e_tx_timeout_ctx and set it as the TX-timeout-recovery flow dump callback.

In the Linux kernel, the following vulnerability has been resolved: mptcp: fix data stream corruption Maxim reported several issues when forcing a TCP transparent proxy to use the MPTCP protocol for the inbound connections. He also provided a clean reproducer. The problem boils down to 'mptcp_frag_can_collapse_to()' assuming that only MPTCP will use the given page_frag. If others - e.g. the plain TCP protocol - allocate page fragments, we can end-up re-using already allocated memory for mptcp_data_frag. Fix the issue ensuring that the to-be-expanded data fragment is located at the current page frag end. v1 -> v2: - added missing fixes tag (Mat)

In the Linux kernel, the following vulnerability has been resolved: nouveau/uvmm: fix addr/range calcs for remap operations dEQP-VK.sparse_resources.image_rebind.2d_array.r64i.128_128_8 was causing a remap operation like the below. op_remap: prev: 0000003fffed0000 00000000000f0000 00000000a5abd18a 0000000000000000 op_remap: next: op_remap: unmap: 0000003fffed0000 0000000000100000 0 op_map: map: 0000003ffffc0000 0000000000010000 000000005b1ba33c 00000000000e0000 This was resulting in an unmap operation from 0x3fffed0000+0xf0000, 0x100000 which was corrupting the pagetables and oopsing the kernel. Fixes the prev + unmap range calcs to use start/end and map back to addr/range.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix UBSAN warning in kv_dpm.c Adds bounds check for sumo_vid_mapping_entry.

IBM Spectrum Protect Client 7.1 and 8.1 is vulnerable to a stack based buffer overflow, caused by improper bounds checking. A local attacker could exploit this vulnerability and cause a denial of service. IBM X-Force ID: 214438.

In the Linux kernel, the following vulnerability has been resolved: gtp: Suppress list corruption splat in gtp_net_exit_batch_rtnl(). Brad Spengler reported the list_del() corruption splat in gtp_net_exit_batch_rtnl(). [0] Commit eb28fd76c0a0 ("gtp: Destroy device along with udp socket's netns dismantle.") added the for_each_netdev() loop in gtp_net_exit_batch_rtnl() to destroy devices in each netns as done in geneve and ip tunnels. However, this could trigger ->dellink() twice for the same device during ->exit_batch_rtnl(). Say we have two netns A & B and gtp device B that resides in netns B but whose UDP socket is in netns A. 1. cleanup_net() processes netns A and then B. 2. gtp_net_exit_batch_rtnl() finds the device B while iterating netns A's gn->gtp_dev_list and calls ->dellink(). [ device B is not yet unlinked from netns B as unregister_netdevice_many() has not been called. ] 3. gtp_net_exit_batch_rtnl() finds the device B while iterating netns B's for_each_netdev() and calls ->dellink(). gtp_dellink() cleans up the device's hash table, unlinks the dev from gn->gtp_dev_list, and calls unregister_netdevice_queue(). Basically, calling gtp_dellink() multiple times is fine unless CONFIG_DEBUG_LIST is enabled. Let's remove for_each_netdev() in gtp_net_exit_batch_rtnl() and delegate the destruction to default_device_exit_batch() as done in bareudp. [0]: list_del corruption, ffff8880aaa62c00->next (autoslab_size_M_dev_P_net_core_dev_11127_8_1328_8_S_4096_A_64_n_139+0xc00/0x1000 [slab object]) is LIST_POISON1 (ffffffffffffff02) (prev is 0xffffffffffffff04) kernel BUG at lib/list_debug.c:58! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN CPU: 1 UID: 0 PID: 1804 Comm: kworker/u8:7 Tainted: G T 6.12.13-grsec-full-20250211091339 #1 Tainted: [T]=RANDSTRUCT Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Workqueue: netns cleanup_net RIP: 0010:[<ffffffff84947381>] __list_del_entry_valid_or_report+0x141/0x200 lib/list_debug.c:58 Code: c2 76 91 31 c0 e8 9f b1 f7 fc 0f 0b 4d 89 f0 48 c7 c1 02 ff ff ff 48 89 ea 48 89 ee 48 c7 c7 e0 c2 76 91 31 c0 e8 7f b1 f7 fc <0f> 0b 4d 89 e8 48 c7 c1 04 ff ff ff 48 89 ea 48 89 ee 48 c7 c7 60 RSP: 0018:fffffe8040b4fbd0 EFLAGS: 00010283 RAX: 00000000000000cc RBX: dffffc0000000000 RCX: ffffffff818c4054 RDX: ffffffff84947381 RSI: ffffffff818d1512 RDI: 0000000000000000 RBP: ffff8880aaa62c00 R08: 0000000000000001 R09: fffffbd008169f32 R10: fffffe8040b4f997 R11: 0000000000000001 R12: a1988d84f24943e4 R13: ffffffffffffff02 R14: ffffffffffffff04 R15: ffff8880aaa62c08 RBX: kasan shadow of 0x0 RCX: __wake_up_klogd.part.0+0x74/0xe0 kernel/printk/printk.c:4554 RDX: __list_del_entry_valid_or_report+0x141/0x200 lib/list_debug.c:58 RSI: vprintk+0x72/0x100 kernel/printk/printk_safe.c:71 RBP: autoslab_size_M_dev_P_net_core_dev_11127_8_1328_8_S_4096_A_64_n_139+0xc00/0x1000 [slab object] RSP: process kstack fffffe8040b4fbd0+0x7bd0/0x8000 [kworker/u8:7+netns 1804 ] R09: kasan shadow of process kstack fffffe8040b4f990+0x7990/0x8000 [kworker/u8:7+netns 1804 ] R10: process kstack fffffe8040b4f997+0x7997/0x8000 [kworker/u8:7+netns 1804 ] R15: autoslab_size_M_dev_P_net_core_dev_11127_8_1328_8_S_4096_A_64_n_139+0xc08/0x1000 [slab object] FS: 0000000000000000(0000) GS:ffff888116000000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000748f5372c000 CR3: 0000000015408000 CR4: 00000000003406f0 shadow CR4: 00000000003406f0 Stack: 0000000000000000 ffffffff8a0c35e7 ffffffff8a0c3603 ffff8880aaa62c00 ffff8880aaa62c00 0000000000000004 ffff88811145311c 0000000000000005 0000000000000001 ffff8880aaa62000 fffffe8040b4fd40 ffffffff8a0c360d Call Trace: <TASK> [<ffffffff8a0c360d>] __list_del_entry_valid include/linux/list.h:131 [inline] fffffe8040b4fc28 [<ffffffff8a0c360d>] __list_del_entry include/linux/list.h:248 [inline] fffffe8040b4fc28 [<ffffffff8a0c360d>] list_del include/linux/list.h:262 [inl ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Stop parsing channels bits when all channels are found. If a usb audio device sets more bits than the amount of channels it could write outside of the map array.

In the Linux kernel, the following vulnerability has been resolved: arm64: entry: fix ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD Currently the ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD workaround isn't quite right, as it is supposed to be applied after the last explicit memory access, but is immediately followed by an LDR. The ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD workaround is used to handle Cortex-A520 erratum 2966298 and Cortex-A510 erratum 3117295, which are described in: * https://developer.arm.com/documentation/SDEN2444153/0600/?lang=en * https://developer.arm.com/documentation/SDEN1873361/1600/?lang=en In both cases the workaround is described as: | If pagetable isolation is disabled, the context switch logic in the | kernel can be updated to execute the following sequence on affected | cores before exiting to EL0, and after all explicit memory accesses: | | 1. A non-shareable TLBI to any context and/or address, including | unused contexts or addresses, such as a `TLBI VALE1 Xzr`. | | 2. A DSB NSH to guarantee completion of the TLBI. The important part being that the TLBI+DSB must be placed "after all explicit memory accesses". Unfortunately, as-implemented, the TLBI+DSB is immediately followed by an LDR, as we have: | alternative_if ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD | tlbi vale1, xzr | dsb nsh | alternative_else_nop_endif | alternative_if_not ARM64_UNMAP_KERNEL_AT_EL0 | ldr lr, [sp, #S_LR] | add sp, sp, #PT_REGS_SIZE // restore sp | eret | alternative_else_nop_endif | | [ ... KPTI exception return path ... ] This patch fixes this by reworking the logic to place the TLBI+DSB immediately before the ERET, after all explicit memory accesses. The ERET is currently in a separate alternative block, and alternatives cannot be nested. To account for this, the alternative block for ARM64_UNMAP_KERNEL_AT_EL0 is replaced with a single alternative branch to skip the KPTI logic, with the new shape of the logic being: | alternative_insn "b .L_skip_tramp_exit_\@", nop, ARM64_UNMAP_KERNEL_AT_EL0 | [ ... KPTI exception return path ... ] | .L_skip_tramp_exit_\@: | | ldr lr, [sp, #S_LR] | add sp, sp, #PT_REGS_SIZE // restore sp | | alternative_if ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD | tlbi vale1, xzr | dsb nsh | alternative_else_nop_endif | eret The new structure means that the workaround is only applied when KPTI is not in use; this is fine as noted in the documented implications of the erratum: | Pagetable isolation between EL0 and higher level ELs prevents the | issue from occurring. ... and as per the workaround description quoted above, the workaround is only necessary "If pagetable isolation is disabled".

In the Linux kernel, the following vulnerability has been resolved: dm-crypt, dm-verity: disable tasklets Tasklets have an inherent problem with memory corruption. The function tasklet_action_common calls tasklet_trylock, then it calls the tasklet callback and then it calls tasklet_unlock. If the tasklet callback frees the structure that contains the tasklet or if it calls some code that may free it, tasklet_unlock will write into free memory. The commits 8e14f610159d and d9a02e016aaf try to fix it for dm-crypt, but it is not a sufficient fix and the data corruption can still happen [1]. There is no fix for dm-verity and dm-verity will write into free memory with every tasklet-processed bio. There will be atomic workqueues implemented in the kernel 6.9 [2]. They will have better interface and they will not suffer from the memory corruption problem. But we need something that stops the memory corruption now and that can be backported to the stable kernels. So, I'm proposing this commit that disables tasklets in both dm-crypt and dm-verity. This commit doesn't remove the tasklet support, because the tasklet code will be reused when atomic workqueues will be implemented. [1] https://lore.kernel.org/all/d390d7ee-f142-44d3-822a-87949e14608b@suse.de/T/ [2] https://lore.kernel.org/lkml/20240130091300.2968534-1-tj@kernel.org/

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_core: Fix possible buffer overflow struct hci_dev_info has a fixed size name[8] field so in the event that hdev->name is bigger than that strcpy would attempt to write past its size, so this fixes this problem by switching to use strscpy.

In the Linux kernel, the following vulnerability has been resolved: libbpf: Use OPTS_SET() macro in bpf_xdp_query() When the feature_flags and xdp_zc_max_segs fields were added to the libbpf bpf_xdp_query_opts, the code writing them did not use the OPTS_SET() macro. This causes libbpf to write to those fields unconditionally, which means that programs compiled against an older version of libbpf (with a smaller size of the bpf_xdp_query_opts struct) will have its stack corrupted by libbpf writing out of bounds. The patch adding the feature_flags field has an early bail out if the feature_flags field is not part of the opts struct (via the OPTS_HAS) macro, but the patch adding xdp_zc_max_segs does not. For consistency, this fix just changes the assignments to both fields to use the OPTS_SET() macro.

In the Linux kernel, the following vulnerability has been resolved: x86/efistub: Use 1:1 file:memory mapping for PE/COFF .compat section The .compat section is a dummy PE section that contains the address of the 32-bit entrypoint of the 64-bit kernel image if it is bootable from 32-bit firmware (i.e., CONFIG_EFI_MIXED=y) This section is only 8 bytes in size and is only referenced from the loader, and so it is placed at the end of the memory view of the image, to avoid the need for padding it to 4k, which is required for sections appearing in the middle of the image. Unfortunately, this violates the PE/COFF spec, and even if most EFI loaders will work correctly (including the Tianocore reference implementation), PE loaders do exist that reject such images, on the basis that both the file and memory views of the file contents should be described by the section headers in a monotonically increasing manner without leaving any gaps. So reorganize the sections to avoid this issue. This results in a slight padding overhead (< 4k) which can be avoided if desired by disabling CONFIG_EFI_MIXED (which is only needed in rare cases these days)

In the Linux kernel, the following vulnerability has been resolved: arp: Prevent overflow in arp_req_get(). syzkaller reported an overflown write in arp_req_get(). [0] When ioctl(SIOCGARP) is issued, arp_req_get() looks up an neighbour entry and copies neigh->ha to struct arpreq.arp_ha.sa_data. The arp_ha here is struct sockaddr, not struct sockaddr_storage, so the sa_data buffer is just 14 bytes. In the splat below, 2 bytes are overflown to the next int field, arp_flags. We initialise the field just after the memcpy(), so it's not a problem. However, when dev->addr_len is greater than 22 (e.g. MAX_ADDR_LEN), arp_netmask is overwritten, which could be set as htonl(0xFFFFFFFFUL) in arp_ioctl() before calling arp_req_get(). To avoid the overflow, let's limit the max length of memcpy(). Note that commit b5f0de6df6dc ("net: dev: Convert sa_data to flexible array in struct sockaddr") just silenced syzkaller. [0]: memcpy: detected field-spanning write (size 16) of single field "r->arp_ha.sa_data" at net/ipv4/arp.c:1128 (size 14) WARNING: CPU: 0 PID: 144638 at net/ipv4/arp.c:1128 arp_req_get+0x411/0x4a0 net/ipv4/arp.c:1128 Modules linked in: CPU: 0 PID: 144638 Comm: syz-executor.4 Not tainted 6.1.74 #31 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-debian-1.16.0-5 04/01/2014 RIP: 0010:arp_req_get+0x411/0x4a0 net/ipv4/arp.c:1128 Code: fd ff ff e8 41 42 de fb b9 0e 00 00 00 4c 89 fe 48 c7 c2 20 6d ab 87 48 c7 c7 80 6d ab 87 c6 05 25 af 72 04 01 e8 5f 8d ad fb <0f> 0b e9 6c fd ff ff e8 13 42 de fb be 03 00 00 00 4c 89 e7 e8 a6 RSP: 0018:ffffc900050b7998 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff88803a815000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffffffff8641a44a RDI: 0000000000000001 RBP: ffffc900050b7a98 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000000 R11: 203a7970636d656d R12: ffff888039c54000 R13: 1ffff92000a16f37 R14: ffff88803a815084 R15: 0000000000000010 FS: 00007f172bf306c0(0000) GS:ffff88805aa00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f172b3569f0 CR3: 0000000057f12005 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> arp_ioctl+0x33f/0x4b0 net/ipv4/arp.c:1261 inet_ioctl+0x314/0x3a0 net/ipv4/af_inet.c:981 sock_do_ioctl+0xdf/0x260 net/socket.c:1204 sock_ioctl+0x3ef/0x650 net/socket.c:1321 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x18e/0x220 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x37/0x90 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x64/0xce RIP: 0033:0x7f172b262b8d Code: 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f172bf300b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007f172b3abf80 RCX: 00007f172b262b8d RDX: 0000000020000000 RSI: 0000000000008954 RDI: 0000000000000003 RBP: 00007f172b2d3493 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 000000000000000b R14: 00007f172b3abf80 R15: 00007f172bf10000 </TASK>