In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Stop parsing channels bits when all channels are found. If a usb audio device sets more bits than the amount of channels it could write outside of the map array.

In the Linux kernel, the following vulnerability has been resolved: iommu/amd: Clear DMA ops when switching domain Since commit 08a27c1c3ecf ("iommu: Add support to change default domain of an iommu group") a user can switch a device between IOMMU and direct DMA through sysfs. This doesn't work for AMD IOMMU at the moment because dev->dma_ops is not cleared when switching from a DMA to an identity IOMMU domain. The DMA layer thus attempts to use the dma-iommu ops on an identity domain, causing an oops: # echo 0000:00:05.0 > /sys/sys/bus/pci/drivers/e1000e/unbind # echo identity > /sys/bus/pci/devices/0000:00:05.0/iommu_group/type # echo 0000:00:05.0 > /sys/sys/bus/pci/drivers/e1000e/bind ... BUG: kernel NULL pointer dereference, address: 0000000000000028 ... Call Trace: iommu_dma_alloc e1000e_setup_tx_resources e1000e_open Since iommu_change_dev_def_domain() calls probe_finalize() again, clear the dma_ops there like Vt-d does.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (w83793) Fix NULL pointer dereference by removing unnecessary structure field If driver read tmp value sufficient for (tmp & 0x08) && (!(tmp & 0x80)) && ((tmp & 0x7) == ((tmp >> 4) & 0x7)) from device then Null pointer dereference occurs. (It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers) Also lm75[] does not serve a purpose anymore after switching to devm_i2c_new_dummy_device() in w83791d_detect_subclients(). The patch fixes possible NULL pointer dereference by removing lm75[]. Found by Linux Driver Verification project (linuxtesting.org). [groeck: Dropped unnecessary continuation lines, fixed multi-line alignments]

In the Linux kernel, the following vulnerability has been resolved: nvmet: fix memory leak in nvmet_alloc_ctrl() When creating ctrl in nvmet_alloc_ctrl(), if the cntlid_min is larger than cntlid_max of the subsystem, and jumps to the "out_free_changed_ns_list" label, but the ctrl->sqs lack of be freed. Fix this by jumping to the "out_free_sqs" label.

In the Linux kernel, the following vulnerability has been resolved: speakup: Fix sizeof() vs ARRAY_SIZE() bug The "buf" pointer is an array of u16 values. This code should be using ARRAY_SIZE() (which is 256) instead of sizeof() (which is 512), otherwise it can the still got out of bounds.

In the Linux kernel, the following vulnerability has been resolved: ALSA: timer: Set lower bound of start tick time Currently ALSA timer doesn't have the lower limit of the start tick time, and it allows a very small size, e.g. 1 tick with 1ns resolution for hrtimer. Such a situation may lead to an unexpected RCU stall, where the callback repeatedly queuing the expire update, as reported by fuzzer. This patch introduces a sanity check of the timer start tick time, so that the system returns an error when a too small start size is set. As of this patch, the lower limit is hard-coded to 100us, which is small enough but can still work somehow.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix potential hang in nilfs_detach_log_writer() Syzbot has reported a potential hang in nilfs_detach_log_writer() called during nilfs2 unmount. Analysis revealed that this is because nilfs_segctor_sync(), which synchronizes with the log writer thread, can be called after nilfs_segctor_destroy() terminates that thread, as shown in the call trace below: nilfs_detach_log_writer nilfs_segctor_destroy nilfs_segctor_kill_thread --> Shut down log writer thread flush_work nilfs_iput_work_func nilfs_dispose_list iput nilfs_evict_inode nilfs_transaction_commit nilfs_construct_segment (if inode needs sync) nilfs_segctor_sync --> Attempt to synchronize with log writer thread *** DEADLOCK *** Fix this issue by changing nilfs_segctor_sync() so that the log writer thread returns normally without synchronizing after it terminates, and by forcing tasks that are already waiting to complete once after the thread terminates. The skipped inode metadata flushout will then be processed together in the subsequent cleanup work in nilfs_segctor_destroy().

In the Linux kernel, the following vulnerability has been resolved: icmp: prevent possible NULL dereferences from icmp_build_probe() First problem is a double call to __in_dev_get_rcu(), because the second one could return NULL. if (__in_dev_get_rcu(dev) && __in_dev_get_rcu(dev)->ifa_list) Second problem is a read from dev->ip6_ptr with no NULL check: if (!list_empty(&rcu_dereference(dev->ip6_ptr)->addr_list)) Use the correct RCU API to fix these. v2: add missing include <net/addrconf.h>

In the Linux kernel, the following vulnerability has been resolved: vt: fix unicode buffer corruption when deleting characters This is the same issue that was fixed for the VGA text buffer in commit 39cdb68c64d8 ("vt: fix memory overlapping when deleting chars in the buffer"). The cure is also the same i.e. replace memcpy() with memmove() due to the overlaping buffers.

In the Linux kernel, the following vulnerability has been resolved: md: Don't suspend the array for interrupted reshape md_start_sync() will suspend the array if there are spares that can be added or removed from conf, however, if reshape is still in progress, this won't happen at all or data will be corrupted(remove_and_add_spares won't be called from md_choose_sync_action for reshape), hence there is no need to suspend the array if reshape is not done yet. Meanwhile, there is a potential deadlock for raid456: 1) reshape is interrupted; 2) set one of the disk WantReplacement, and add a new disk to the array, however, recovery won't start until the reshape is finished; 3) then issue an IO across reshpae position, this IO will wait for reshape to make progress; 4) continue to reshape, then md_start_sync() found there is a spare disk that can be added to conf, mddev_suspend() is called; Step 4 and step 3 is waiting for each other, deadlock triggered. Noted this problem is found by code review, and it's not reporduced yet. Fix this porblem by don't suspend the array for interrupted reshape, this is safe because conf won't be changed until reshape is done.

In the Linux kernel, the following vulnerability has been resolved: net: ip_tunnel: prevent perpetual headroom growth syzkaller triggered following kasan splat: BUG: KASAN: use-after-free in __skb_flow_dissect+0x19d1/0x7a50 net/core/flow_dissector.c:1170 Read of size 1 at addr ffff88812fb4000e by task syz-executor183/5191 [..] kasan_report+0xda/0x110 mm/kasan/report.c:588 __skb_flow_dissect+0x19d1/0x7a50 net/core/flow_dissector.c:1170 skb_flow_dissect_flow_keys include/linux/skbuff.h:1514 [inline] ___skb_get_hash net/core/flow_dissector.c:1791 [inline] __skb_get_hash+0xc7/0x540 net/core/flow_dissector.c:1856 skb_get_hash include/linux/skbuff.h:1556 [inline] ip_tunnel_xmit+0x1855/0x33c0 net/ipv4/ip_tunnel.c:748 ipip_tunnel_xmit+0x3cc/0x4e0 net/ipv4/ipip.c:308 __netdev_start_xmit include/linux/netdevice.h:4940 [inline] netdev_start_xmit include/linux/netdevice.h:4954 [inline] xmit_one net/core/dev.c:3548 [inline] dev_hard_start_xmit+0x13d/0x6d0 net/core/dev.c:3564 __dev_queue_xmit+0x7c1/0x3d60 net/core/dev.c:4349 dev_queue_xmit include/linux/netdevice.h:3134 [inline] neigh_connected_output+0x42c/0x5d0 net/core/neighbour.c:1592 ... ip_finish_output2+0x833/0x2550 net/ipv4/ip_output.c:235 ip_finish_output+0x31/0x310 net/ipv4/ip_output.c:323 .. iptunnel_xmit+0x5b4/0x9b0 net/ipv4/ip_tunnel_core.c:82 ip_tunnel_xmit+0x1dbc/0x33c0 net/ipv4/ip_tunnel.c:831 ipgre_xmit+0x4a1/0x980 net/ipv4/ip_gre.c:665 __netdev_start_xmit include/linux/netdevice.h:4940 [inline] netdev_start_xmit include/linux/netdevice.h:4954 [inline] xmit_one net/core/dev.c:3548 [inline] dev_hard_start_xmit+0x13d/0x6d0 net/core/dev.c:3564 ... The splat occurs because skb->data points past skb->head allocated area. This is because neigh layer does: __skb_pull(skb, skb_network_offset(skb)); ... but skb_network_offset() returns a negative offset and __skb_pull() arg is unsigned. IOW, we skb->data gets "adjusted" by a huge value. The negative value is returned because skb->head and skb->data distance is more than 64k and skb->network_header (u16) has wrapped around. The bug is in the ip_tunnel infrastructure, which can cause dev->needed_headroom to increment ad infinitum. The syzkaller reproducer consists of packets getting routed via a gre tunnel, and route of gre encapsulated packets pointing at another (ipip) tunnel. The ipip encapsulation finds gre0 as next output device. This results in the following pattern: 1). First packet is to be sent out via gre0. Route lookup found an output device, ipip0. 2). ip_tunnel_xmit for gre0 bumps gre0->needed_headroom based on the future output device, rt.dev->needed_headroom (ipip0). 3). ip output / start_xmit moves skb on to ipip0. which runs the same code path again (xmit recursion). 4). Routing step for the post-gre0-encap packet finds gre0 as output device to use for ipip0 encapsulated packet. tunl0->needed_headroom is then incremented based on the (already bumped) gre0 device headroom. This repeats for every future packet: gre0->needed_headroom gets inflated because previous packets' ipip0 step incremented rt->dev (gre0) headroom, and ipip0 incremented because gre0 needed_headroom was increased. For each subsequent packet, gre/ipip0->needed_headroom grows until post-expand-head reallocations result in a skb->head/data distance of more than 64k. Once that happens, skb->network_header (u16) wraps around when pskb_expand_head tries to make sure that skb_network_offset() is unchanged after the headroom expansion/reallocation. After this skb_network_offset(skb) returns a different (and negative) result post headroom expansion. The next trip to neigh layer (or anything else that would __skb_pull the network header) makes skb->data point to a memory location outside skb->head area. v2: Cap the needed_headroom update to an arbitarily chosen upperlimit to prevent perpetual increase instead of dropping the headroom increment completely.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/fence: Fix oops due to non-matching drm_sched init/fini Currently amdgpu calls drm_sched_fini() from the fence driver sw fini routine - such function is expected to be called only after the respective init function - drm_sched_init() - was executed successfully. Happens that we faced a driver probe failure in the Steam Deck recently, and the function drm_sched_fini() was called even without its counter-part had been previously called, causing the following oops: amdgpu: probe of 0000:04:00.0 failed with error -110 BUG: kernel NULL pointer dereference, address: 0000000000000090 PGD 0 P4D 0 Oops: 0002 [#1] PREEMPT SMP NOPTI CPU: 0 PID: 609 Comm: systemd-udevd Not tainted 6.2.0-rc3-gpiccoli #338 Hardware name: Valve Jupiter/Jupiter, BIOS F7A0113 11/04/2022 RIP: 0010:drm_sched_fini+0x84/0xa0 [gpu_sched] [...] Call Trace: <TASK> amdgpu_fence_driver_sw_fini+0xc8/0xd0 [amdgpu] amdgpu_device_fini_sw+0x2b/0x3b0 [amdgpu] amdgpu_driver_release_kms+0x16/0x30 [amdgpu] devm_drm_dev_init_release+0x49/0x70 [...] To prevent that, check if the drm_sched was properly initialized for a given ring before calling its fini counter-part. Notice ideally we'd use sched.ready for that; such field is set as the latest thing on drm_sched_init(). But amdgpu seems to "override" the meaning of such field - in the above oops for example, it was a GFX ring causing the crash, and the sched.ready field was set to true in the ring init routine, regardless of the state of the DRM scheduler. Hence, we ended-up using sched.ops as per Christian's suggestion [0], and also removed the no_scheduler check [1]. [0] https://lore.kernel.org/amd-gfx/984ee981-2906-0eaf-ccec-9f80975cb136@amd.com/ [1] https://lore.kernel.org/amd-gfx/cd0e2994-f85f-d837-609f-7056d5fb7231@amd.com/

In the Linux kernel, the following vulnerability has been resolved: sysv: don't call sb_bread() with pointers_lock held syzbot is reporting sleep in atomic context in SysV filesystem [1], for sb_bread() is called with rw_spinlock held. A "write_lock(&pointers_lock) => read_lock(&pointers_lock) deadlock" bug and a "sb_bread() with write_lock(&pointers_lock)" bug were introduced by "Replace BKL for chain locking with sysvfs-private rwlock" in Linux 2.5.12. Then, "[PATCH] err1-40: sysvfs locking fix" in Linux 2.6.8 fixed the former bug by moving pointers_lock lock to the callers, but instead introduced a "sb_bread() with read_lock(&pointers_lock)" bug (which made this problem easier to hit). Al Viro suggested that why not to do like get_branch()/get_block()/ find_shared() in Minix filesystem does. And doing like that is almost a revert of "[PATCH] err1-40: sysvfs locking fix" except that get_branch() from with find_shared() is called without write_lock(&pointers_lock).

In the Linux kernel, the following vulnerability has been resolved: of: module: prevent NULL pointer dereference in vsnprintf() In of_modalias(), we can get passed the str and len parameters which would cause a kernel oops in vsnprintf() since it only allows passing a NULL ptr when the length is also 0. Also, we need to filter out the negative values of the len parameter as these will result in a really huge buffer since snprintf() takes size_t parameter while ours is ssize_t... Found by Linux Verification Center (linuxtesting.org) with the Svace static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: net: ip_tunnel: make sure to pull inner header in ip_tunnel_rcv() Apply the same fix than ones found in : 8d975c15c0cd ("ip6_tunnel: make sure to pull inner header in __ip6_tnl_rcv()") 1ca1ba465e55 ("geneve: make sure to pull inner header in geneve_rx()") We have to save skb->network_header in a temporary variable in order to be able to recompute the network_header pointer after a pskb_inet_may_pull() call. pskb_inet_may_pull() makes sure the needed headers are in skb->head. syzbot reported: BUG: KMSAN: uninit-value in __INET_ECN_decapsulate include/net/inet_ecn.h:253 [inline] BUG: KMSAN: uninit-value in INET_ECN_decapsulate include/net/inet_ecn.h:275 [inline] BUG: KMSAN: uninit-value in IP_ECN_decapsulate include/net/inet_ecn.h:302 [inline] BUG: KMSAN: uninit-value in ip_tunnel_rcv+0xed9/0x2ed0 net/ipv4/ip_tunnel.c:409 __INET_ECN_decapsulate include/net/inet_ecn.h:253 [inline] INET_ECN_decapsulate include/net/inet_ecn.h:275 [inline] IP_ECN_decapsulate include/net/inet_ecn.h:302 [inline] ip_tunnel_rcv+0xed9/0x2ed0 net/ipv4/ip_tunnel.c:409 __ipgre_rcv+0x9bc/0xbc0 net/ipv4/ip_gre.c:389 ipgre_rcv net/ipv4/ip_gre.c:411 [inline] gre_rcv+0x423/0x19f0 net/ipv4/ip_gre.c:447 gre_rcv+0x2a4/0x390 net/ipv4/gre_demux.c:163 ip_protocol_deliver_rcu+0x264/0x1300 net/ipv4/ip_input.c:205 ip_local_deliver_finish+0x2b8/0x440 net/ipv4/ip_input.c:233 NF_HOOK include/linux/netfilter.h:314 [inline] ip_local_deliver+0x21f/0x490 net/ipv4/ip_input.c:254 dst_input include/net/dst.h:461 [inline] ip_rcv_finish net/ipv4/ip_input.c:449 [inline] NF_HOOK include/linux/netfilter.h:314 [inline] ip_rcv+0x46f/0x760 net/ipv4/ip_input.c:569 __netif_receive_skb_one_core net/core/dev.c:5534 [inline] __netif_receive_skb+0x1a6/0x5a0 net/core/dev.c:5648 netif_receive_skb_internal net/core/dev.c:5734 [inline] netif_receive_skb+0x58/0x660 net/core/dev.c:5793 tun_rx_batched+0x3ee/0x980 drivers/net/tun.c:1556 tun_get_user+0x53b9/0x66e0 drivers/net/tun.c:2009 tun_chr_write_iter+0x3af/0x5d0 drivers/net/tun.c:2055 call_write_iter include/linux/fs.h:2087 [inline] new_sync_write fs/read_write.c:497 [inline] vfs_write+0xb6b/0x1520 fs/read_write.c:590 ksys_write+0x20f/0x4c0 fs/read_write.c:643 __do_sys_write fs/read_write.c:655 [inline] __se_sys_write fs/read_write.c:652 [inline] __x64_sys_write+0x93/0xd0 fs/read_write.c:652 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b Uninit was created at: __alloc_pages+0x9a6/0xe00 mm/page_alloc.c:4590 alloc_pages_mpol+0x62b/0x9d0 mm/mempolicy.c:2133 alloc_pages+0x1be/0x1e0 mm/mempolicy.c:2204 skb_page_frag_refill+0x2bf/0x7c0 net/core/sock.c:2909 tun_build_skb drivers/net/tun.c:1686 [inline] tun_get_user+0xe0a/0x66e0 drivers/net/tun.c:1826 tun_chr_write_iter+0x3af/0x5d0 drivers/net/tun.c:2055 call_write_iter include/linux/fs.h:2087 [inline] new_sync_write fs/read_write.c:497 [inline] vfs_write+0xb6b/0x1520 fs/read_write.c:590 ksys_write+0x20f/0x4c0 fs/read_write.c:643 __do_sys_write fs/read_write.c:655 [inline] __se_sys_write fs/read_write.c:652 [inline] __x64_sys_write+0x93/0xd0 fs/read_write.c:652 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b

In the Linux kernel, the following vulnerability has been resolved: dma-buf: Fix NULL pointer dereference in sanitycheck() If due to a memory allocation failure mock_chain() returns NULL, it is passed to dma_fence_enable_sw_signaling() resulting in NULL pointer dereference there. Call dma_fence_enable_sw_signaling() only if mock_chain() succeeds. Found by Linux Verification Center (linuxtesting.org) with SVACE.

A vulnerability was found in Linux Kernel. It has been declared as problematic. Affected by this vulnerability is the function intr_callback of the file drivers/net/usb/r8152.c of the component BPF. The manipulation leads to logging of excessive data. The attack can be launched remotely. It is recommended to apply a patch to fix this issue. The associated identifier of this vulnerability is VDB-211363.

A vulnerability classified as problematic was found in Linux Kernel. This vulnerability affects the function macvlan_handle_frame of the file drivers/net/macvlan.c of the component skb. The manipulation leads to memory leak. The attack can be initiated remotely. It is recommended to apply a patch to fix this issue. The identifier of this vulnerability is VDB-211024.

In the Linux kernel, the following vulnerability has been resolved: spi: sun6i: reduce DMA RX transfer width to single byte Through empirical testing it has been determined that sometimes RX SPI transfers with DMA enabled return corrupted data. This is down to single or even multiple bytes lost during DMA transfer from SPI peripheral to memory. It seems the RX FIFO within the SPI peripheral can become confused when performing bus read accesses wider than a single byte to it during an active SPI transfer. This patch reduces the width of individual DMA read accesses to the RX FIFO to a single byte to mitigate that issue.

In the Linux kernel, the following vulnerability has been resolved: comedi: dt9812: fix DMA buffers on stack USB transfer buffers are typically mapped for DMA and must not be allocated on the stack or transfers will fail. Allocate proper transfer buffers in the various command helpers and return an error on short transfers instead of acting on random stack data. Note that this also fixes a stack info leak on systems where DMA is not used as 32 bytes are always sent to the device regardless of how short the command is.

In the Linux kernel, the following vulnerability has been resolved: mt76: fix potential DMA mapping leak With buf uninitialized in mt76_dma_tx_queue_skb_raw, its field skip_unmap could potentially inherit a non-zero value from stack garbage. If this happens, it will cause DMA mappings for MCU command frames to not be unmapped after completion

In the Linux kernel, the following vulnerability has been resolved: kunit: fix reference count leak in kfree_at_end The reference counting issue happens in the normal path of kfree_at_end(). When kunit_alloc_and_get_resource() is invoked, the function forgets to handle the returned resource object, whose refcount increased inside, causing a refcount leak. Fix this issue by calling kunit_alloc_resource() instead of kunit_alloc_and_get_resource(). Fixed the following when applying: Shuah Khan <skhan@linuxfoundation.org> CHECK: Alignment should match open parenthesis + kunit_alloc_resource(test, NULL, kfree_res_free, GFP_KERNEL, (void *)to_free);

In the Linux kernel, the following vulnerability has been resolved: do_sys_name_to_handle(): use kzalloc() to fix kernel-infoleak syzbot identified a kernel information leak vulnerability in do_sys_name_to_handle() and issued the following report [1]. [1] "BUG: KMSAN: kernel-infoleak in instrument_copy_to_user include/linux/instrumented.h:114 [inline] BUG: KMSAN: kernel-infoleak in _copy_to_user+0xbc/0x100 lib/usercopy.c:40 instrument_copy_to_user include/linux/instrumented.h:114 [inline] _copy_to_user+0xbc/0x100 lib/usercopy.c:40 copy_to_user include/linux/uaccess.h:191 [inline] do_sys_name_to_handle fs/fhandle.c:73 [inline] __do_sys_name_to_handle_at fs/fhandle.c:112 [inline] __se_sys_name_to_handle_at+0x949/0xb10 fs/fhandle.c:94 __x64_sys_name_to_handle_at+0xe4/0x140 fs/fhandle.c:94 ... Uninit was created at: slab_post_alloc_hook+0x129/0xa70 mm/slab.h:768 slab_alloc_node mm/slub.c:3478 [inline] __kmem_cache_alloc_node+0x5c9/0x970 mm/slub.c:3517 __do_kmalloc_node mm/slab_common.c:1006 [inline] __kmalloc+0x121/0x3c0 mm/slab_common.c:1020 kmalloc include/linux/slab.h:604 [inline] do_sys_name_to_handle fs/fhandle.c:39 [inline] __do_sys_name_to_handle_at fs/fhandle.c:112 [inline] __se_sys_name_to_handle_at+0x441/0xb10 fs/fhandle.c:94 __x64_sys_name_to_handle_at+0xe4/0x140 fs/fhandle.c:94 ... Bytes 18-19 of 20 are uninitialized Memory access of size 20 starts at ffff888128a46380 Data copied to user address 0000000020000240" Per Chuck Lever's suggestion, use kzalloc() instead of kmalloc() to solve the problem.

In the Linux kernel, the following vulnerability has been resolved: qibfs: fix dentry leak simple_recursive_removal() drops the pinning references to all positives in subtree. For the cases when its argument has been kept alive by the pinning alone that's exactly the right thing to do, but here the argument comes from dcache lookup, that needs to be balanced by explicit dput(). Fucked-up-by: Al Viro <viro@zeniv.linux.org.uk>

In the Linux kernel, the following vulnerability has been resolved: bpf, sockmap: Fix NULL pointer dereference in sk_psock_verdict_data_ready() syzbot reported the following NULL pointer dereference issue [1]: BUG: kernel NULL pointer dereference, address: 0000000000000000 [...] RIP: 0010:0x0 [...] Call Trace: <TASK> sk_psock_verdict_data_ready+0x232/0x340 net/core/skmsg.c:1230 unix_stream_sendmsg+0x9b4/0x1230 net/unix/af_unix.c:2293 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x221/0x270 net/socket.c:745 ____sys_sendmsg+0x525/0x7d0 net/socket.c:2584 ___sys_sendmsg net/socket.c:2638 [inline] __sys_sendmsg+0x2b0/0x3a0 net/socket.c:2667 do_syscall_64+0xf9/0x240 entry_SYSCALL_64_after_hwframe+0x6f/0x77 If sk_psock_verdict_data_ready() and sk_psock_stop_verdict() are called concurrently, psock->saved_data_ready can be NULL, causing the above issue. This patch fixes this issue by calling the appropriate data ready function using the sk_psock_data_ready() helper and protecting it from concurrency with sk->sk_callback_lock.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Adding array index check to prevent memory corruption [Why & How] Array indices out of bound caused memory corruption. Adding checks to ensure that array index stays in bound.

In the Linux kernel, the following vulnerability has been resolved: vmxnet3: Fix packet corruption in vmxnet3_xdp_xmit_frame Andrew and Nikolay reported connectivity issues with Cilium's service load-balancing in case of vmxnet3. If a BPF program for native XDP adds an encapsulation header such as IPIP and transmits the packet out the same interface, then in case of vmxnet3 a corrupted packet is being sent and subsequently dropped on the path. vmxnet3_xdp_xmit_frame() which is called e.g. via vmxnet3_run_xdp() through vmxnet3_xdp_xmit_back() calculates an incorrect DMA address: page = virt_to_page(xdpf->data); tbi->dma_addr = page_pool_get_dma_addr(page) + VMXNET3_XDP_HEADROOM; dma_sync_single_for_device(&adapter->pdev->dev, tbi->dma_addr, buf_size, DMA_TO_DEVICE); The above assumes a fixed offset (VMXNET3_XDP_HEADROOM), but the XDP BPF program could have moved xdp->data. While the passed buf_size is correct (xdpf->len), the dma_addr needs to have a dynamic offset which can be calculated as xdpf->data - (void *)xdpf, that is, xdp->data - xdp->data_hard_start.

In the Linux kernel, the following vulnerability has been resolved: nfs/localio: must clear res.replen in nfs_local_read_done Otherwise memory corruption can occur due to NFSv3 LOCALIO reads leaving garbage in res.replen: - nfs3_read_done() copies that into server->read_hdrsize; from there nfs3_proc_read_setup() copies it to args.replen in new requests. - nfs3_xdr_enc_read3args() passes that to rpc_prepare_reply_pages() which includes it in hdrsize for xdr_init_pages, so that rq_rcv_buf contains a ridiculous len. - This is copied to rq_private_buf and xs_read_stream_request() eventually passes the kvec to sock_recvmsg() which receives incoming data into entirely the wrong place. This is easily reproduced with NFSv3 LOCALIO that is servicing reads when it is made to pivot back to using normal RPC. This switch back to using normal NFSv3 with RPC can occur for a few reasons but this issue was exposed with a test that stops and then restarts the NFSv3 server while LOCALIO is performing heavy read IO.

In the Linux kernel, the following vulnerability has been resolved: HID: betop: fix slab-out-of-bounds Write in betop_probe Syzbot reported slab-out-of-bounds Write bug in hid-betopff driver. The problem is the driver assumes the device must have an input report but some malicious devices violate this assumption. So this patch checks hid_device's input is non empty before it's been used.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/ufence: Prefetch ufence addr to catch bogus address access_ok() only checks for addr overflow so also try to read the addr to catch invalid addr sent from userspace. (cherry picked from commit 9408c4508483ffc60811e910a93d6425b8e63928)

In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Skip parsing frames of type UVC_VS_UNDEFINED in uvc_parse_format This can lead to out of bounds writes since frames of this type were not taken into account when calculating the size of the frames buffer in uvc_parse_streaming.

In the Linux kernel, the following vulnerability has been resolved: initramfs: avoid filename buffer overrun The initramfs filename field is defined in Documentation/driver-api/early-userspace/buffer-format.rst as: 37 cpio_file := ALGN(4) + cpio_header + filename + "\0" + ALGN(4) + data ... 55 ============= ================== ========================= 56 Field name Field size Meaning 57 ============= ================== ========================= ... 70 c_namesize 8 bytes Length of filename, including final \0 When extracting an initramfs cpio archive, the kernel's do_name() path handler assumes a zero-terminated path at @collected, passing it directly to filp_open() / init_mkdir() / init_mknod(). If a specially crafted cpio entry carries a non-zero-terminated filename and is followed by uninitialized memory, then a file may be created with trailing characters that represent the uninitialized memory. The ability to create an initramfs entry would imply already having full control of the system, so the buffer overrun shouldn't be considered a security vulnerability. Append the output of the following bash script to an existing initramfs and observe any created /initramfs_test_fname_overrunAA* path. E.g. ./reproducer.sh | gzip >> /myinitramfs It's easiest to observe non-zero uninitialized memory when the output is gzipped, as it'll overflow the heap allocated @out_buf in __gunzip(), rather than the initrd_start+initrd_size block. ---- reproducer.sh ---- nilchar="A" # change to "\0" to properly zero terminate / pad magic="070701" ino=1 mode=$(( 0100777 )) uid=0 gid=0 nlink=1 mtime=1 filesize=0 devmajor=0 devminor=1 rdevmajor=0 rdevminor=0 csum=0 fname="initramfs_test_fname_overrun" namelen=$(( ${#fname} + 1 )) # plus one to account for terminator printf "%s%08x%08x%08x%08x%08x%08x%08x%08x%08x%08x%08x%08x%08x%s" \ $magic $ino $mode $uid $gid $nlink $mtime $filesize \ $devmajor $devminor $rdevmajor $rdevminor $namelen $csum $fname termpadlen=$(( 1 + ((4 - ((110 + $namelen) & 3)) % 4) )) printf "%.s${nilchar}" $(seq 1 $termpadlen) ---- reproducer.sh ---- Symlink filename fields handled in do_symlink() won't overrun past the data segment, due to the explicit zero-termination of the symlink target. Fix filename buffer overrun by aborting the initramfs FSM if any cpio entry doesn't carry a zero-terminator at the expected (name_len - 1) offset.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/pm: Vangogh: Fix kernel memory out of bounds write KASAN reports that the GPU metrics table allocated in vangogh_tables_init() is not large enough for the memset done in smu_cmn_init_soft_gpu_metrics(). Condensed report follows: [ 33.861314] BUG: KASAN: slab-out-of-bounds in smu_cmn_init_soft_gpu_metrics+0x73/0x200 [amdgpu] [ 33.861799] Write of size 168 at addr ffff888129f59500 by task mangoapp/1067 ... [ 33.861808] CPU: 6 UID: 1000 PID: 1067 Comm: mangoapp Tainted: G W 6.12.0-rc4 #356 1a56f59a8b5182eeaf67eb7cb8b13594dd23b544 [ 33.861816] Tainted: [W]=WARN [ 33.861818] Hardware name: Valve Galileo/Galileo, BIOS F7G0107 12/01/2023 [ 33.861822] Call Trace: [ 33.861826] <TASK> [ 33.861829] dump_stack_lvl+0x66/0x90 [ 33.861838] print_report+0xce/0x620 [ 33.861853] kasan_report+0xda/0x110 [ 33.862794] kasan_check_range+0xfd/0x1a0 [ 33.862799] __asan_memset+0x23/0x40 [ 33.862803] smu_cmn_init_soft_gpu_metrics+0x73/0x200 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.863306] vangogh_get_gpu_metrics_v2_4+0x123/0xad0 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.864257] vangogh_common_get_gpu_metrics+0xb0c/0xbc0 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.865682] amdgpu_dpm_get_gpu_metrics+0xcc/0x110 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.866160] amdgpu_get_gpu_metrics+0x154/0x2d0 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.867135] dev_attr_show+0x43/0xc0 [ 33.867147] sysfs_kf_seq_show+0x1f1/0x3b0 [ 33.867155] seq_read_iter+0x3f8/0x1140 [ 33.867173] vfs_read+0x76c/0xc50 [ 33.867198] ksys_read+0xfb/0x1d0 [ 33.867214] do_syscall_64+0x90/0x160 ... [ 33.867353] Allocated by task 378 on cpu 7 at 22.794876s: [ 33.867358] kasan_save_stack+0x33/0x50 [ 33.867364] kasan_save_track+0x17/0x60 [ 33.867367] __kasan_kmalloc+0x87/0x90 [ 33.867371] vangogh_init_smc_tables+0x3f9/0x840 [amdgpu] [ 33.867835] smu_sw_init+0xa32/0x1850 [amdgpu] [ 33.868299] amdgpu_device_init+0x467b/0x8d90 [amdgpu] [ 33.868733] amdgpu_driver_load_kms+0x19/0xf0 [amdgpu] [ 33.869167] amdgpu_pci_probe+0x2d6/0xcd0 [amdgpu] [ 33.869608] local_pci_probe+0xda/0x180 [ 33.869614] pci_device_probe+0x43f/0x6b0 Empirically we can confirm that the former allocates 152 bytes for the table, while the latter memsets the 168 large block. Root cause appears that when GPU metrics tables for v2_4 parts were added it was not considered to enlarge the table to fit. The fix in this patch is rather "brute force" and perhaps later should be done in a smarter way, by extracting and consolidating the part version to size logic to a common helper, instead of brute forcing the largest possible allocation. Nevertheless, for now this works and fixes the out of bounds write. v2: * Drop impossible v3_0 case. (Mario) (cherry picked from commit 0880f58f9609f0200483a49429af0f050d281703)

In the Linux kernel, the following vulnerability has been resolved: bpf, arm64: Fix address emission with tag-based KASAN enabled When BPF_TRAMP_F_CALL_ORIG is enabled, the address of a bpf_tramp_image struct on the stack is passed during the size calculation pass and an address on the heap is passed during code generation. This may cause a heap buffer overflow if the heap address is tagged because emit_a64_mov_i64() will emit longer code than it did during the size calculation pass. The same problem could occur without tag-based KASAN if one of the 16-bit words of the stack address happened to be all-ones during the size calculation pass. Fix the problem by assuming the worst case (4 instructions) when calculating the size of the bpf_tramp_image address emission.

In the Linux kernel, the following vulnerability has been resolved: uprobe: avoid out-of-bounds memory access of fetching args Uprobe needs to fetch args into a percpu buffer, and then copy to ring buffer to avoid non-atomic context problem. Sometimes user-space strings, arrays can be very large, but the size of percpu buffer is only page size. And store_trace_args() won't check whether these data exceeds a single page or not, caused out-of-bounds memory access. It could be reproduced by following steps: 1. build kernel with CONFIG_KASAN enabled 2. save follow program as test.c ``` \#include <stdio.h> \#include <stdlib.h> \#include <string.h> // If string length large than MAX_STRING_SIZE, the fetch_store_strlen() // will return 0, cause __get_data_size() return shorter size, and // store_trace_args() will not trigger out-of-bounds access. // So make string length less than 4096. \#define STRLEN 4093 void generate_string(char *str, int n) { int i; for (i = 0; i < n; ++i) { char c = i % 26 + 'a'; str[i] = c; } str[n-1] = '\0'; } void print_string(char *str) { printf("%s\n", str); } int main() { char tmp[STRLEN]; generate_string(tmp, STRLEN); print_string(tmp); return 0; } ``` 3. compile program `gcc -o test test.c` 4. get the offset of `print_string()` ``` objdump -t test | grep -w print_string 0000000000401199 g F .text 000000000000001b print_string ``` 5. configure uprobe with offset 0x1199 ``` off=0x1199 cd /sys/kernel/debug/tracing/ echo "p /root/test:${off} arg1=+0(%di):ustring arg2=\$comm arg3=+0(%di):ustring" > uprobe_events echo 1 > events/uprobes/enable echo 1 > tracing_on ``` 6. run `test`, and kasan will report error. ================================================================== BUG: KASAN: use-after-free in strncpy_from_user+0x1d6/0x1f0 Write of size 8 at addr ffff88812311c004 by task test/499CPU: 0 UID: 0 PID: 499 Comm: test Not tainted 6.12.0-rc3+ #18 Hardware name: Red Hat KVM, BIOS 1.16.0-4.al8 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x55/0x70 print_address_description.constprop.0+0x27/0x310 kasan_report+0x10f/0x120 ? strncpy_from_user+0x1d6/0x1f0 strncpy_from_user+0x1d6/0x1f0 ? rmqueue.constprop.0+0x70d/0x2ad0 process_fetch_insn+0xb26/0x1470 ? __pfx_process_fetch_insn+0x10/0x10 ? _raw_spin_lock+0x85/0xe0 ? __pfx__raw_spin_lock+0x10/0x10 ? __pte_offset_map+0x1f/0x2d0 ? unwind_next_frame+0xc5f/0x1f80 ? arch_stack_walk+0x68/0xf0 ? is_bpf_text_address+0x23/0x30 ? kernel_text_address.part.0+0xbb/0xd0 ? __kernel_text_address+0x66/0xb0 ? unwind_get_return_address+0x5e/0xa0 ? __pfx_stack_trace_consume_entry+0x10/0x10 ? arch_stack_walk+0xa2/0xf0 ? _raw_spin_lock_irqsave+0x8b/0xf0 ? __pfx__raw_spin_lock_irqsave+0x10/0x10 ? depot_alloc_stack+0x4c/0x1f0 ? _raw_spin_unlock_irqrestore+0xe/0x30 ? stack_depot_save_flags+0x35d/0x4f0 ? kasan_save_stack+0x34/0x50 ? kasan_save_stack+0x24/0x50 ? mutex_lock+0x91/0xe0 ? __pfx_mutex_lock+0x10/0x10 prepare_uprobe_buffer.part.0+0x2cd/0x500 uprobe_dispatcher+0x2c3/0x6a0 ? __pfx_uprobe_dispatcher+0x10/0x10 ? __kasan_slab_alloc+0x4d/0x90 handler_chain+0xdd/0x3e0 handle_swbp+0x26e/0x3d0 ? __pfx_handle_swbp+0x10/0x10 ? uprobe_pre_sstep_notifier+0x151/0x1b0 irqentry_exit_to_user_mode+0xe2/0x1b0 asm_exc_int3+0x39/0x40 RIP: 0033:0x401199 Code: 01 c2 0f b6 45 fb 88 02 83 45 fc 01 8b 45 fc 3b 45 e4 7c b7 8b 45 e4 48 98 48 8d 50 ff 48 8b 45 e8 48 01 d0 ce RSP: 002b:00007ffdf00576a8 EFLAGS: 00000206 RAX: 00007ffdf00576b0 RBX: 0000000000000000 RCX: 0000000000000ff2 RDX: 0000000000000ffc RSI: 0000000000000ffd RDI: 00007ffdf00576b0 RBP: 00007ffdf00586b0 R08: 00007feb2f9c0d20 R09: 00007feb2f9c0d20 R10: 0000000000000001 R11: 0000000000000202 R12: 0000000000401040 R13: 00007ffdf0058780 R14: 0000000000000000 R15: 0000000000000000 </TASK> This commit enforces the buffer's maxlen less than a page-size to avoid store_trace_args() out-of-memory access.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix kernel bug due to missing clearing of checked flag Syzbot reported that in directory operations after nilfs2 detects filesystem corruption and degrades to read-only, __block_write_begin_int(), which is called to prepare block writes, may fail the BUG_ON check for accesses exceeding the folio/page size, triggering a kernel bug. This was found to be because the "checked" flag of a page/folio was not cleared when it was discarded by nilfs2's own routine, which causes the sanity check of directory entries to be skipped when the directory page/folio is reloaded. So, fix that. This was necessary when the use of nilfs2's own page discard routine was applied to more than just metadata files.

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: core: Validate channel ID when processing command completions MHI reads the channel ID from the event ring element sent by the device which can be any value between 0 and 255. In order to prevent any out of bound accesses, add a check against the maximum number of channels supported by the controller and those channels not configured yet so as to skip processing of that event ring element.

In the Linux kernel, the following vulnerability has been resolved: soc: qcom: cmd-db: Map shared memory as WC, not WB Linux does not write into cmd-db region. This region of memory is write protected by XPU. XPU may sometime falsely detect clean cache eviction as "write" into the write protected region leading to secure interrupt which causes an endless loop somewhere in Trust Zone. The only reason it is working right now is because Qualcomm Hypervisor maps the same region as Non-Cacheable memory in Stage 2 translation tables. The issue manifests if we want to use another hypervisor (like Xen or KVM), which does not know anything about those specific mappings. Changing the mapping of cmd-db memory from MEMREMAP_WB to MEMREMAP_WT/WC removes dependency on correct mappings in Stage 2 tables. This patch fixes the issue by updating the mapping to MEMREMAP_WC. I tested this on SA8155P with Xen.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Validate TA binary size Add TA binary size validation to avoid OOB write. (cherry picked from commit c0a04e3570d72aaf090962156ad085e37c62e442)

In the Linux kernel, the following vulnerability has been resolved: erofs: fix out-of-bound access when z_erofs_gbuf_growsize() partially fails If z_erofs_gbuf_growsize() partially fails on a global buffer due to memory allocation failure or fault injection (as reported by syzbot [1]), new pages need to be freed by comparing to the existing pages to avoid memory leaks. However, the old gbuf->pages[] array may not be large enough, which can lead to null-ptr-deref or out-of-bound access. Fix this by checking against gbuf->nrpages in advance. [1] https://lore.kernel.org/r/000000000000f7b96e062018c6e3@google.com

In the Linux kernel, the following vulnerability has been resolved: powerpc/rtas: Prevent Spectre v1 gadget construction in sys_rtas() Smatch warns: arch/powerpc/kernel/rtas.c:1932 __do_sys_rtas() warn: potential spectre issue 'args.args' [r] (local cap) The 'nargs' and 'nret' locals come directly from a user-supplied buffer and are used as indexes into a small stack-based array and as inputs to copy_to_user() after they are subject to bounds checks. Use array_index_nospec() after the bounds checks to clamp these values for speculative execution.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix a kernel verifier crash in stacksafe() Daniel Hodges reported a kernel verifier crash when playing with sched-ext. Further investigation shows that the crash is due to invalid memory access in stacksafe(). More specifically, it is the following code: if (exact != NOT_EXACT && old->stack[spi].slot_type[i % BPF_REG_SIZE] != cur->stack[spi].slot_type[i % BPF_REG_SIZE]) return false; The 'i' iterates old->allocated_stack. If cur->allocated_stack < old->allocated_stack the out-of-bound access will happen. To fix the issue add 'i >= cur->allocated_stack' check such that if the condition is true, stacksafe() should fail. Otherwise, cur->stack[spi].slot_type[i % BPF_REG_SIZE] memory access is legal.

In the Linux kernel, the following vulnerability has been resolved: mptcp: fix data stream corruption Maxim reported several issues when forcing a TCP transparent proxy to use the MPTCP protocol for the inbound connections. He also provided a clean reproducer. The problem boils down to 'mptcp_frag_can_collapse_to()' assuming that only MPTCP will use the given page_frag. If others - e.g. the plain TCP protocol - allocate page fragments, we can end-up re-using already allocated memory for mptcp_data_frag. Fix the issue ensuring that the to-be-expanded data fragment is located at the current page frag end. v1 -> v2: - added missing fixes tag (Mat)

In the Linux kernel, the following vulnerability has been resolved: spi: bcm2835: Fix out-of-bounds access with more than 4 slaves Commit 571e31fa60b3 ("spi: bcm2835: Cache CS register value for ->prepare_message()") limited the number of slaves to 3 at compile-time. The limitation was necessitated by a statically-sized array prepare_cs[] in the driver private data which contains a per-slave register value. The commit sought to enforce the limitation at run-time by setting the controller's num_chipselect to 3: Slaves with a higher chipselect are rejected by spi_add_device(). However the commit neglected that num_chipselect only limits the number of *native* chipselects. If GPIO chipselects are specified in the device tree for more than 3 slaves, num_chipselect is silently raised by of_spi_get_gpio_numbers() and the result are out-of-bounds accesses to the statically-sized array prepare_cs[]. As a bandaid fix which is backportable to stable, raise the number of allowed slaves to 24 (which "ought to be enough for anybody"), enforce the limitation on slave ->setup and revert num_chipselect to 3 (which is the number of native chipselects supported by the controller). An upcoming for-next commit will allow an arbitrary number of slaves.

In the Linux kernel, the following vulnerability has been resolved: fix bitmap corruption on close_range() with CLOSE_RANGE_UNSHARE copy_fd_bitmaps(new, old, count) is expected to copy the first count/BITS_PER_LONG bits from old->full_fds_bits[] and fill the rest with zeroes. What it does is copying enough words (BITS_TO_LONGS(count/BITS_PER_LONG)), then memsets the rest. That works fine, *if* all bits past the cutoff point are clear. Otherwise we are risking garbage from the last word we'd copied. For most of the callers that is true - expand_fdtable() has count equal to old->max_fds, so there's no open descriptors past count, let alone fully occupied words in ->open_fds[], which is what bits in ->full_fds_bits[] correspond to. The other caller (dup_fd()) passes sane_fdtable_size(old_fdt, max_fds), which is the smallest multiple of BITS_PER_LONG that covers all opened descriptors below max_fds. In the common case (copying on fork()) max_fds is ~0U, so all opened descriptors will be below it and we are fine, by the same reasons why the call in expand_fdtable() is safe. Unfortunately, there is a case where max_fds is less than that and where we might, indeed, end up with junk in ->full_fds_bits[] - close_range(from, to, CLOSE_RANGE_UNSHARE) with * descriptor table being currently shared * 'to' being above the current capacity of descriptor table * 'from' being just under some chunk of opened descriptors. In that case we end up with observably wrong behaviour - e.g. spawn a child with CLONE_FILES, get all descriptors in range 0..127 open, then close_range(64, ~0U, CLOSE_RANGE_UNSHARE) and watch dup(0) ending up with descriptor #128, despite #64 being observably not open. The minimally invasive fix would be to deal with that in dup_fd(). If this proves to add measurable overhead, we can go that way, but let's try to fix copy_fd_bitmaps() first. * new helper: bitmap_copy_and_expand(to, from, bits_to_copy, size). * make copy_fd_bitmaps() take the bitmap size in words, rather than bits; it's 'count' argument is always a multiple of BITS_PER_LONG, so we are not losing any information, and that way we can use the same helper for all three bitmaps - compiler will see that count is a multiple of BITS_PER_LONG for the large ones, so it'll generate plain memcpy()+memset(). Reproducer added to tools/testing/selftests/core/close_range_test.c

In the Linux kernel, the following vulnerability has been resolved: s390/dasd: fix error recovery leading to data corruption on ESE devices Extent Space Efficient (ESE) or thin provisioned volumes need to be formatted on demand during usual IO processing. The dasd_ese_needs_format function checks for error codes that signal the non existence of a proper track format. The check for incorrect length is to imprecise since other error cases leading to transport of insufficient data also have this flag set. This might lead to data corruption in certain error cases for example during a storage server warmstart. Fix by removing the check for incorrect length and replacing by explicitly checking for invalid track format in transport mode. Also remove the check for file protected since this is not a valid ESE handling case.

In the Linux kernel, the following vulnerability has been resolved: igb: cope with large MAX_SKB_FRAGS Sabrina reports that the igb driver does not cope well with large MAX_SKB_FRAG values: setting MAX_SKB_FRAG to 45 causes payload corruption on TX. An easy reproducer is to run ssh to connect to the machine. With MAX_SKB_FRAGS=17 it works, with MAX_SKB_FRAGS=45 it fails. This has been reported originally in https://bugzilla.redhat.com/show_bug.cgi?id=2265320 The root cause of the issue is that the driver does not take into account properly the (possibly large) shared info size when selecting the ring layout, and will try to fit two packets inside the same 4K page even when the 1st fraglist will trump over the 2nd head. Address the issue by checking if 2K buffers are insufficient.

In the Linux kernel, the following vulnerability has been resolved: md/raid1: Fix data corruption for degraded array with slow disk read_balance() will avoid reading from slow disks as much as possible, however, if valid data only lands in slow disks, and a new normal disk is still in recovery, unrecovered data can be read: raid1_read_request read_balance raid1_should_read_first -> return false choose_best_rdev -> normal disk is not recovered, return -1 choose_bb_rdev -> missing the checking of recovery, return the normal disk -> read unrecovered data Root cause is that the checking of recovery is missing in choose_bb_rdev(). Hence add such checking to fix the problem. Also fix similar problem in choose_slow_rdev().

In the Linux kernel, the following vulnerability has been resolved: mm/vmalloc: fix page mapping if vm_area_alloc_pages() with high order fallback to order 0 The __vmap_pages_range_noflush() assumes its argument pages** contains pages with the same page shift. However, since commit e9c3cda4d86e ("mm, vmalloc: fix high order __GFP_NOFAIL allocations"), if gfp_flags includes __GFP_NOFAIL with high order in vm_area_alloc_pages() and page allocation failed for high order, the pages** may contain two different page shifts (high order and order-0). This could lead __vmap_pages_range_noflush() to perform incorrect mappings, potentially resulting in memory corruption. Users might encounter this as follows (vmap_allow_huge = true, 2M is for PMD_SIZE): kvmalloc(2M, __GFP_NOFAIL|GFP_X) __vmalloc_node_range_noprof(vm_flags=VM_ALLOW_HUGE_VMAP) vm_area_alloc_pages(order=9) ---> order-9 allocation failed and fallback to order-0 vmap_pages_range() vmap_pages_range_noflush() __vmap_pages_range_noflush(page_shift = 21) ----> wrong mapping happens We can remove the fallback code because if a high-order allocation fails, __vmalloc_node_range_noprof() will retry with order-0. Therefore, it is unnecessary to fallback to order-0 here. Therefore, fix this by removing the fallback code.

In the Linux kernel, the following vulnerability has been resolved: bna: adjust 'name' buf size of bna_tcb and bna_ccb structures To have enough space to write all possible sprintf() args. Currently 'name' size is 16, but the first '%s' specifier may already need at least 16 characters, since 'bnad->netdev->name' is used there. For '%d' specifiers, assume that they require: * 1 char for 'tx_id + tx_info->tcb[i]->id' sum, BNAD_MAX_TXQ_PER_TX is 8 * 2 chars for 'rx_id + rx_info->rx_ctrl[i].ccb->id', BNAD_MAX_RXP_PER_RX is 16 And replace sprintf with snprintf. Detected using the static analysis tool - Svace.