In the Linux kernel, the following vulnerability has been resolved: fbdev: savage: Handle err return when savagefb_check_var failed The commit 04e5eac8f3ab("fbdev: savage: Error out if pixclock equals zero") checks the value of pixclock to avoid divide-by-zero error. However the function savagefb_probe doesn't handle the error return of savagefb_check_var. When pixclock is 0, it will cause divide-by-zero error.

In the Linux kernel, the following vulnerability has been resolved: soc: bcm: Check for NULL return of devm_kzalloc() As the potential failure of allocation, devm_kzalloc() may return NULL. Then the 'pd->pmb' and the follow lines of code may bring null pointer dereference. Therefore, it is better to check the return value of devm_kzalloc() to avoid this confusion.

In the Linux kernel, the following vulnerability has been resolved: tcp: add accessors to read/set tp->snd_cwnd We had various bugs over the years with code breaking the assumption that tp->snd_cwnd is greater than zero. Lately, syzbot reported the WARN_ON_ONCE(!tp->prior_cwnd) added in commit 8b8a321ff72c ("tcp: fix zero cwnd in tcp_cwnd_reduction") can trigger, and without a repro we would have to spend considerable time finding the bug. Instead of complaining too late, we want to catch where and when tp->snd_cwnd is set to an illegal value.

In the Linux kernel, the following vulnerability has been resolved: net: phy: at803x: fix NULL pointer dereference on AR9331 PHY Latest kernel will explode on the PHY interrupt config, since it depends now on allocated priv. So, run probe to allocate priv to fix it. ar9331_switch ethernet.1:10 lan0 (uninitialized): PHY [!ahb!ethernet@1a000000!mdio!switch@10:00] driver [Qualcomm Atheros AR9331 built-in PHY] (irq=13) CPU 0 Unable to handle kernel paging request at virtual address 0000000a, epc == 8050e8a8, ra == 80504b34 ... Call Trace: [<8050e8a8>] at803x_config_intr+0x5c/0xd0 [<80504b34>] phy_request_interrupt+0xa8/0xd0 [<8050289c>] phylink_bringup_phy+0x2d8/0x3ac [<80502b68>] phylink_fwnode_phy_connect+0x118/0x130 [<8074d8ec>] dsa_slave_create+0x270/0x420 [<80743b04>] dsa_port_setup+0x12c/0x148 [<8074580c>] dsa_register_switch+0xaf0/0xcc0 [<80511344>] ar9331_sw_probe+0x370/0x388 [<8050cb78>] mdio_probe+0x44/0x70 [<804df300>] really_probe+0x200/0x424 [<804df7b4>] __driver_probe_device+0x290/0x298 [<804df810>] driver_probe_device+0x54/0xe4 [<804dfd50>] __device_attach_driver+0xe4/0x130 [<804dcb00>] bus_for_each_drv+0xb4/0xd8 [<804dfac4>] __device_attach+0x104/0x1a4 [<804ddd24>] bus_probe_device+0x48/0xc4 [<804deb44>] deferred_probe_work_func+0xf0/0x10c [<800a0ffc>] process_one_work+0x314/0x4d4 [<800a17fc>] worker_thread+0x2a4/0x354 [<800a9a54>] kthread+0x134/0x13c [<8006306c>] ret_from_kernel_thread+0x14/0x1c Same Issue would affect some other PHYs (QCA8081, QCA9561), so fix it too.

In the Linux kernel, the following vulnerability has been resolved: xfrm: fix refcount leak in __xfrm_policy_check() The issue happens on an error path in __xfrm_policy_check(). When the fetching process of the object `pols[1]` fails, the function simply returns 0, forgetting to decrement the reference count of `pols[0]`, which is incremented earlier by either xfrm_sk_policy_lookup() or xfrm_policy_lookup(). This may result in memory leaks. Fix it by decreasing the reference count of `pols[0]` in that path.

In the Linux kernel, the following vulnerability has been resolved: cpufreq: governor: Use kobject release() method to free dbs_data The struct dbs_data embeds a struct gov_attr_set and the struct gov_attr_set embeds a kobject. Since every kobject must have a release() method and we can't use kfree() to free it directly, so introduce cpufreq_dbs_data_release() to release the dbs_data via the kobject::release() method. This fixes the calltrace like below: ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x34 WARNING: CPU: 12 PID: 810 at lib/debugobjects.c:505 debug_print_object+0xb8/0x100 Modules linked in: CPU: 12 PID: 810 Comm: sh Not tainted 5.16.0-next-20220120-yocto-standard+ #536 Hardware name: Marvell OcteonTX CN96XX board (DT) pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : debug_print_object+0xb8/0x100 lr : debug_print_object+0xb8/0x100 sp : ffff80001dfcf9a0 x29: ffff80001dfcf9a0 x28: 0000000000000001 x27: ffff0001464f0000 x26: 0000000000000000 x25: ffff8000090e3f00 x24: ffff80000af60210 x23: ffff8000094dfb78 x22: ffff8000090e3f00 x21: ffff0001080b7118 x20: ffff80000aeb2430 x19: ffff800009e8f5e0 x18: 0000000000000000 x17: 0000000000000002 x16: 00004d62e58be040 x15: 013590470523aff8 x14: ffff8000090e1828 x13: 0000000001359047 x12: 00000000f5257d14 x11: 0000000000040591 x10: 0000000066c1ffea x9 : ffff8000080d15e0 x8 : ffff80000a1765a8 x7 : 0000000000000000 x6 : 0000000000000001 x5 : ffff800009e8c000 x4 : ffff800009e8c760 x3 : 0000000000000000 x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff0001474ed040 Call trace: debug_print_object+0xb8/0x100 __debug_check_no_obj_freed+0x1d0/0x25c debug_check_no_obj_freed+0x24/0xa0 kfree+0x11c/0x440 cpufreq_dbs_governor_exit+0xa8/0xac cpufreq_exit_governor+0x44/0x90 cpufreq_set_policy+0x29c/0x570 store_scaling_governor+0x110/0x154 store+0xb0/0xe0 sysfs_kf_write+0x58/0x84 kernfs_fop_write_iter+0x12c/0x1c0 new_sync_write+0xf0/0x18c vfs_write+0x1cc/0x220 ksys_write+0x74/0x100 __arm64_sys_write+0x28/0x3c invoke_syscall.constprop.0+0x58/0xf0 do_el0_svc+0x70/0x170 el0_svc+0x54/0x190 el0t_64_sync_handler+0xa4/0x130 el0t_64_sync+0x1a0/0x1a4 irq event stamp: 189006 hardirqs last enabled at (189005): [<ffff8000080849d0>] finish_task_switch.isra.0+0xe0/0x2c0 hardirqs last disabled at (189006): [<ffff8000090667a4>] el1_dbg+0x24/0xa0 softirqs last enabled at (188966): [<ffff8000080106d0>] __do_softirq+0x4b0/0x6a0 softirqs last disabled at (188957): [<ffff80000804a618>] __irq_exit_rcu+0x108/0x1a4 [ rjw: Because can be freed by the gov_attr_set_put() in cpufreq_dbs_governor_exit() now, it is also necessary to put the invocation of the governor ->exit() callback into the new cpufreq_dbs_data_release() function. ]

In the Linux kernel, the following vulnerability has been resolved: binder: fix alloc->vma_vm_mm null-ptr dereference Syzbot reported a couple issues introduced by commit 44e602b4e52f ("binder_alloc: add missing mmap_lock calls when using the VMA"), in which we attempt to acquire the mmap_lock when alloc->vma_vm_mm has not been initialized yet. This can happen if a binder_proc receives a transaction without having previously called mmap() to setup the binder_proc->alloc space in [1]. Also, a similar issue occurs via binder_alloc_print_pages() when we try to dump the debugfs binder stats file in [2]. Sample of syzbot's crash report: ================================================================== KASAN: null-ptr-deref in range [0x0000000000000128-0x000000000000012f] CPU: 0 PID: 3755 Comm: syz-executor229 Not tainted 6.0.0-rc1-next-20220819-syzkaller #0 syz-executor229[3755] cmdline: ./syz-executor2294415195 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/22/2022 RIP: 0010:__lock_acquire+0xd83/0x56d0 kernel/locking/lockdep.c:4923 [...] Call Trace: <TASK> lock_acquire kernel/locking/lockdep.c:5666 [inline] lock_acquire+0x1ab/0x570 kernel/locking/lockdep.c:5631 down_read+0x98/0x450 kernel/locking/rwsem.c:1499 mmap_read_lock include/linux/mmap_lock.h:117 [inline] binder_alloc_new_buf_locked drivers/android/binder_alloc.c:405 [inline] binder_alloc_new_buf+0xa5/0x19e0 drivers/android/binder_alloc.c:593 binder_transaction+0x242e/0x9a80 drivers/android/binder.c:3199 binder_thread_write+0x664/0x3220 drivers/android/binder.c:3986 binder_ioctl_write_read drivers/android/binder.c:5036 [inline] binder_ioctl+0x3470/0x6d00 drivers/android/binder.c:5323 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x193/0x200 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd [...] ================================================================== Fix these issues by setting up alloc->vma_vm_mm pointer during open() and caching directly from current->mm. This guarantees we have a valid reference to take the mmap_lock during scenarios described above. [1] https://syzkaller.appspot.com/bug?extid=f7dc54e5be28950ac459 [2] https://syzkaller.appspot.com/bug?extid=a75ebe0452711c9e56d9

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix deadlock in nilfs_count_free_blocks() A semaphore deadlock can occur if nilfs_get_block() detects metadata corruption while locating data blocks and a superblock writeback occurs at the same time: task 1 task 2 ------ ------ * A file operation * nilfs_truncate() nilfs_get_block() down_read(rwsem A) <-- nilfs_bmap_lookup_contig() ... generic_shutdown_super() nilfs_put_super() * Prepare to write superblock * down_write(rwsem B) <-- nilfs_cleanup_super() * Detect b-tree corruption * nilfs_set_log_cursor() nilfs_bmap_convert_error() nilfs_count_free_blocks() __nilfs_error() down_read(rwsem A) <-- nilfs_set_error() down_write(rwsem B) <-- *** DEADLOCK *** Here, nilfs_get_block() readlocks rwsem A (= NILFS_MDT(dat_inode)->mi_sem) and then calls nilfs_bmap_lookup_contig(), but if it fails due to metadata corruption, __nilfs_error() is called from nilfs_bmap_convert_error() inside the lock section. Since __nilfs_error() calls nilfs_set_error() unless the filesystem is read-only and nilfs_set_error() attempts to writelock rwsem B (= nilfs->ns_sem) to write back superblock exclusively, hierarchical lock acquisition occurs in the order rwsem A -> rwsem B. Now, if another task starts updating the superblock, it may writelock rwsem B during the lock sequence above, and can deadlock trying to readlock rwsem A in nilfs_count_free_blocks(). However, there is actually no need to take rwsem A in nilfs_count_free_blocks() because it, within the lock section, only reads a single integer data on a shared struct with nilfs_sufile_get_ncleansegs(). This has been the case after commit aa474a220180 ("nilfs2: add local variable to cache the number of clean segments"), that is, even before this bug was introduced. So, this resolves the deadlock problem by just not taking the semaphore in nilfs_count_free_blocks().

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: possible module reference underflow in error path dst->ops is set on when nft_expr_clone() fails, but module refcount has not been bumped yet, therefore nft_expr_destroy() leads to module reference underflow.

In the Linux kernel, the following vulnerability has been resolved: ARM: versatile: Add missing of_node_put in dcscb_init The device_node pointer is returned by of_find_compatible_node with refcount incremented. We should use of_node_put() to avoid the refcount leak.

In the Linux kernel, the following vulnerability has been resolved: KVM: Don't null dereference ops->destroy A KVM device cleanup happens in either of two callbacks: 1) destroy() which is called when the VM is being destroyed; 2) release() which is called when a device fd is closed. Most KVM devices use 1) but Book3s's interrupt controller KVM devices (XICS, XIVE, XIVE-native) use 2) as they need to close and reopen during the machine execution. The error handling in kvm_ioctl_create_device() assumes destroy() is always defined which leads to NULL dereference as discovered by Syzkaller. This adds a checks for destroy!=NULL and adds a missing release(). This is not changing kvm_destroy_devices() as devices with defined release() should have been removed from the KVM devices list by then.

In the Linux kernel, the following vulnerability has been resolved: arm64: asm-bug: Add .align 2 to the end of __BUG_ENTRY When CONFIG_DEBUG_BUGVERBOSE=n, we fail to add necessary padding bytes to bug_table entries, and as a result the last entry in a bug table will be ignored, potentially leading to an unexpected panic(). All prior entries in the table will be handled correctly. The arm64 ABI requires that struct fields of up to 8 bytes are naturally-aligned, with padding added within a struct such that struct are suitably aligned within arrays. When CONFIG_DEBUG_BUGVERPOSE=y, the layout of a bug_entry is: struct bug_entry { signed int bug_addr_disp; // 4 bytes signed int file_disp; // 4 bytes unsigned short line; // 2 bytes unsigned short flags; // 2 bytes } ... with 12 bytes total, requiring 4-byte alignment. When CONFIG_DEBUG_BUGVERBOSE=n, the layout of a bug_entry is: struct bug_entry { signed int bug_addr_disp; // 4 bytes unsigned short flags; // 2 bytes < implicit padding > // 2 bytes } ... with 8 bytes total, with 6 bytes of data and 2 bytes of trailing padding, requiring 4-byte alginment. When we create a bug_entry in assembly, we align the start of the entry to 4 bytes, which implicitly handles padding for any prior entries. However, we do not align the end of the entry, and so when CONFIG_DEBUG_BUGVERBOSE=n, the final entry lacks the trailing padding bytes. For the main kernel image this is not a problem as find_bug() doesn't depend on the trailing padding bytes when searching for entries: for (bug = __start___bug_table; bug < __stop___bug_table; ++bug) if (bugaddr == bug_addr(bug)) return bug; However for modules, module_bug_finalize() depends on the trailing bytes when calculating the number of entries: mod->num_bugs = sechdrs[i].sh_size / sizeof(struct bug_entry); ... and as the last bug_entry lacks the necessary padding bytes, this entry will not be counted, e.g. in the case of a single entry: sechdrs[i].sh_size == 6 sizeof(struct bug_entry) == 8; sechdrs[i].sh_size / sizeof(struct bug_entry) == 0; Consequently module_find_bug() will miss the last bug_entry when it does: for (i = 0; i < mod->num_bugs; ++i, ++bug) if (bugaddr == bug_addr(bug)) goto out; ... which can lead to a kenrel panic due to an unhandled bug. This can be demonstrated with the following module: static int __init buginit(void) { WARN(1, "hello\n"); return 0; } static void __exit bugexit(void) { } module_init(buginit); module_exit(bugexit); MODULE_LICENSE("GPL"); ... which will trigger a kernel panic when loaded: ------------[ cut here ]------------ hello Unexpected kernel BRK exception at EL1 Internal error: BRK handler: 00000000f2000800 [#1] PREEMPT SMP Modules linked in: hello(O+) CPU: 0 PID: 50 Comm: insmod Tainted: G O 6.9.1 #8 Hardware name: linux,dummy-virt (DT) pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : buginit+0x18/0x1000 [hello] lr : buginit+0x18/0x1000 [hello] sp : ffff800080533ae0 x29: ffff800080533ae0 x28: 0000000000000000 x27: 0000000000000000 x26: ffffaba8c4e70510 x25: ffff800080533c30 x24: ffffaba8c4a28a58 x23: 0000000000000000 x22: 0000000000000000 x21: ffff3947c0eab3c0 x20: ffffaba8c4e3f000 x19: ffffaba846464000 x18: 0000000000000006 x17: 0000000000000000 x16: ffffaba8c2492834 x15: 0720072007200720 x14: 0720072007200720 x13: ffffaba8c49b27c8 x12: 0000000000000312 x11: 0000000000000106 x10: ffffaba8c4a0a7c8 x9 : ffffaba8c49b27c8 x8 : 00000000ffffefff x7 : ffffaba8c4a0a7c8 x6 : 80000000fffff000 x5 : 0000000000000107 x4 : 0000000000000000 x3 : 0000000000000000 x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff3947c0eab3c0 Call trace: buginit+0x18/0x1000 [hello] do_one_initcall+0x80/0x1c8 do_init_module+0x60/0x218 load_module+0x1ba4/0x1d70 __do_sys_init_module+0x198/0x1d0 __arm64_sys_init_module+0x1c/0x28 invoke_syscall+0x48/0x114 el0_svc ---truncated---

In the Linux kernel, the following vulnerability has been resolved: KVM: SVM: WARN on vNMI + NMI window iff NMIs are outright masked When requesting an NMI window, WARN on vNMI support being enabled if and only if NMIs are actually masked, i.e. if the vCPU is already handling an NMI. KVM's ABI for NMIs that arrive simultanesouly (from KVM's point of view) is to inject one NMI and pend the other. When using vNMI, KVM pends the second NMI simply by setting V_NMI_PENDING, and lets the CPU do the rest (hardware automatically sets V_NMI_BLOCKING when an NMI is injected). However, if KVM can't immediately inject an NMI, e.g. because the vCPU is in an STI shadow or is running with GIF=0, then KVM will request an NMI window and trigger the WARN (but still function correctly). Whether or not the GIF=0 case makes sense is debatable, as the intent of KVM's behavior is to provide functionality that is as close to real hardware as possible. E.g. if two NMIs are sent in quick succession, the probability of both NMIs arriving in an STI shadow is infinitesimally low on real hardware, but significantly larger in a virtual environment, e.g. if the vCPU is preempted in the STI shadow. For GIF=0, the argument isn't as clear cut, because the window where two NMIs can collide is much larger in bare metal (though still small). That said, KVM should not have divergent behavior for the GIF=0 case based on whether or not vNMI support is enabled. And KVM has allowed simultaneous NMIs with GIF=0 for over a decade, since commit 7460fb4a3400 ("KVM: Fix simultaneous NMIs"). I.e. KVM's GIF=0 handling shouldn't be modified without a *really* good reason to do so, and if KVM's behavior were to be modified, it should be done irrespective of vNMI support.

In the Linux kernel, the following vulnerability has been resolved: PCI: mediatek: Fix refcount leak in mtk_pcie_subsys_powerup() The of_find_compatible_node() function returns a node pointer with refcount incremented, We should use of_node_put() on it when done Add the missing of_node_put() to release the refcount.

In the Linux kernel, the following vulnerability has been resolved: irqchip/apple-aic: Fix refcount leak in aic_of_ic_init of_get_child_by_name() returns a node pointer with refcount incremented, we should use of_node_put() on it when not need anymore. Add missing of_node_put() to avoid refcount leak.

In the Linux kernel, the following vulnerability has been resolved: spi: spi-fsl-qspi: check return value after calling platform_get_resource_byname() It will cause null-ptr-deref if platform_get_resource_byname() returns NULL, we need check the return value.

In the Linux kernel, the following vulnerability has been resolved: apparmor: fix reference count leak in aa_pivotroot() The aa_pivotroot() function has a reference counting bug in a specific path. When aa_replace_current_label() returns on success, the function forgets to decrement the reference count of “target”, which is increased earlier by build_pivotroot(), causing a reference leak. Fix it by decreasing the refcount of “target” in that path.

In the Linux kernel, the following vulnerability has been resolved: video: fbdev: clcdfb: Fix refcount leak in clcdfb_of_vram_setup of_parse_phandle() returns a node pointer with refcount incremented, we should use of_node_put() on it when not need anymore. Add missing of_node_put() to avoid refcount leak.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hfi1: Prevent panic when SDMA is disabled If the hfi1 module is loaded with HFI1_CAP_SDMA off, a call to hfi1_write_iter() will dereference a NULL pointer and panic. A typical stack frame is: sdma_select_user_engine [hfi1] hfi1_user_sdma_process_request [hfi1] hfi1_write_iter [hfi1] do_iter_readv_writev do_iter_write vfs_writev do_writev do_syscall_64 The fix is to test for SDMA in hfi1_write_iter() and fail the I/O with EINVAL.

In the Linux kernel, the following vulnerability has been resolved: cxl/region: Fix cxl_region leak, cleanup targets at region delete When a region is deleted any targets that have been previously assigned to that region hold references to it. Trigger those references to drop by detaching all targets at unregister_region() time. Otherwise that region object will leak as userspace has lost the ability to detach targets once region sysfs is torn down.

In the Linux kernel, the following vulnerability has been resolved: mtd: rawnand: intel: fix possible null-ptr-deref in ebu_nand_probe() It will cause null-ptr-deref when using 'res', if platform_get_resource() returns NULL, so move using 'res' after devm_ioremap_resource() that will check it to avoid null-ptr-deref.

In the Linux kernel, the following vulnerability has been resolved: gfs2: Always check inode size of inline inodes Check if the inode size of stuffed (inline) inodes is within the allowed range when reading inodes from disk (gfs2_dinode_in()). This prevents us from on-disk corruption. The two checks in stuffed_readpage() and gfs2_unstuffer_page() that just truncate inline data to the maximum allowed size don't actually make sense, and they can be removed now as well.

In the Linux kernel, the following vulnerability has been resolved: tunnels: do not assume mac header is set in skb_tunnel_check_pmtu() Recently added debug in commit f9aefd6b2aa3 ("net: warn if mac header was not set") caught a bug in skb_tunnel_check_pmtu(), as shown in this syzbot report [1]. In ndo_start_xmit() paths, there is really no need to use skb->mac_header, because skb->data is supposed to point at it. [1] WARNING: CPU: 1 PID: 8604 at include/linux/skbuff.h:2784 skb_mac_header_len include/linux/skbuff.h:2784 [inline] WARNING: CPU: 1 PID: 8604 at include/linux/skbuff.h:2784 skb_tunnel_check_pmtu+0x5de/0x2f90 net/ipv4/ip_tunnel_core.c:413 Modules linked in: CPU: 1 PID: 8604 Comm: syz-executor.3 Not tainted 5.19.0-rc2-syzkaller-00443-g8720bd951b8e #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:skb_mac_header_len include/linux/skbuff.h:2784 [inline] RIP: 0010:skb_tunnel_check_pmtu+0x5de/0x2f90 net/ipv4/ip_tunnel_core.c:413 Code: 00 00 00 00 fc ff df 4c 89 fa 48 c1 ea 03 80 3c 02 00 0f 84 b9 fe ff ff 4c 89 ff e8 7c 0f d7 f9 e9 ac fe ff ff e8 c2 13 8a f9 <0f> 0b e9 28 fc ff ff e8 b6 13 8a f9 48 8b 54 24 70 48 b8 00 00 00 RSP: 0018:ffffc90002e4f520 EFLAGS: 00010212 RAX: 0000000000000324 RBX: ffff88804d5fd500 RCX: ffffc90005b52000 RDX: 0000000000040000 RSI: ffffffff87f05e3e RDI: 0000000000000003 RBP: ffffc90002e4f650 R08: 0000000000000003 R09: 000000000000ffff R10: 000000000000ffff R11: 0000000000000000 R12: 000000000000ffff R13: 0000000000000000 R14: 000000000000ffcd R15: 000000000000001f FS: 00007f3babba9700(0000) GS:ffff8880b9b00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000080 CR3: 0000000075319000 CR4: 00000000003506e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> geneve_xmit_skb drivers/net/geneve.c:927 [inline] geneve_xmit+0xcf8/0x35d0 drivers/net/geneve.c:1107 __netdev_start_xmit include/linux/netdevice.h:4805 [inline] netdev_start_xmit include/linux/netdevice.h:4819 [inline] __dev_direct_xmit+0x500/0x730 net/core/dev.c:4309 dev_direct_xmit include/linux/netdevice.h:3007 [inline] packet_direct_xmit+0x1b8/0x2c0 net/packet/af_packet.c:282 packet_snd net/packet/af_packet.c:3073 [inline] packet_sendmsg+0x21f4/0x55d0 net/packet/af_packet.c:3104 sock_sendmsg_nosec net/socket.c:714 [inline] sock_sendmsg+0xcf/0x120 net/socket.c:734 ____sys_sendmsg+0x6eb/0x810 net/socket.c:2489 ___sys_sendmsg+0xf3/0x170 net/socket.c:2543 __sys_sendmsg net/socket.c:2572 [inline] __do_sys_sendmsg net/socket.c:2581 [inline] __se_sys_sendmsg net/socket.c:2579 [inline] __x64_sys_sendmsg+0x132/0x220 net/socket.c:2579 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x46/0xb0 RIP: 0033:0x7f3baaa89109 Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f3babba9168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f3baab9bf60 RCX: 00007f3baaa89109 RDX: 0000000000000000 RSI: 0000000020000a00 RDI: 0000000000000003 RBP: 00007f3baaae305d R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007ffe74f2543f R14: 00007f3babba9300 R15: 0000000000022000 </TASK>

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Move cfg_log_verbose check before calling lpfc_dmp_dbg() In an attempt to log message 0126 with LOG_TRACE_EVENT, the following hard lockup call trace hangs the system. Call Trace: _raw_spin_lock_irqsave+0x32/0x40 lpfc_dmp_dbg.part.32+0x28/0x220 [lpfc] lpfc_cmpl_els_fdisc+0x145/0x460 [lpfc] lpfc_sli_cancel_jobs+0x92/0xd0 [lpfc] lpfc_els_flush_cmd+0x43c/0x670 [lpfc] lpfc_els_flush_all_cmd+0x37/0x60 [lpfc] lpfc_sli4_async_event_proc+0x956/0x1720 [lpfc] lpfc_do_work+0x1485/0x1d70 [lpfc] kthread+0x112/0x130 ret_from_fork+0x1f/0x40 Kernel panic - not syncing: Hard LOCKUP The same CPU tries to claim the phba->port_list_lock twice. Move the cfg_log_verbose checks as part of the lpfc_printf_vlog() and lpfc_printf_log() macros before calling lpfc_dmp_dbg(). There is no need to take the phba->port_list_lock within lpfc_dmp_dbg().

In the Linux kernel, the following vulnerability has been resolved: scsi: storvsc: Remove WQ_MEM_RECLAIM from storvsc_error_wq storvsc_error_wq workqueue should not be marked as WQ_MEM_RECLAIM as it doesn't need to make forward progress under memory pressure. Marking this workqueue as WQ_MEM_RECLAIM may cause deadlock while flushing a non-WQ_MEM_RECLAIM workqueue. In the current state it causes the following warning: [ 14.506347] ------------[ cut here ]------------ [ 14.506354] workqueue: WQ_MEM_RECLAIM storvsc_error_wq_0:storvsc_remove_lun is flushing !WQ_MEM_RECLAIM events_freezable_power_:disk_events_workfn [ 14.506360] WARNING: CPU: 0 PID: 8 at <-snip->kernel/workqueue.c:2623 check_flush_dependency+0xb5/0x130 [ 14.506390] CPU: 0 PID: 8 Comm: kworker/u4:0 Not tainted 5.4.0-1086-azure #91~18.04.1-Ubuntu [ 14.506391] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.1 05/09/2022 [ 14.506393] Workqueue: storvsc_error_wq_0 storvsc_remove_lun [ 14.506395] RIP: 0010:check_flush_dependency+0xb5/0x130 <-snip-> [ 14.506408] Call Trace: [ 14.506412] __flush_work+0xf1/0x1c0 [ 14.506414] __cancel_work_timer+0x12f/0x1b0 [ 14.506417] ? kernfs_put+0xf0/0x190 [ 14.506418] cancel_delayed_work_sync+0x13/0x20 [ 14.506420] disk_block_events+0x78/0x80 [ 14.506421] del_gendisk+0x3d/0x2f0 [ 14.506423] sr_remove+0x28/0x70 [ 14.506427] device_release_driver_internal+0xef/0x1c0 [ 14.506428] device_release_driver+0x12/0x20 [ 14.506429] bus_remove_device+0xe1/0x150 [ 14.506431] device_del+0x167/0x380 [ 14.506432] __scsi_remove_device+0x11d/0x150 [ 14.506433] scsi_remove_device+0x26/0x40 [ 14.506434] storvsc_remove_lun+0x40/0x60 [ 14.506436] process_one_work+0x209/0x400 [ 14.506437] worker_thread+0x34/0x400 [ 14.506439] kthread+0x121/0x140 [ 14.506440] ? process_one_work+0x400/0x400 [ 14.506441] ? kthread_park+0x90/0x90 [ 14.506443] ret_from_fork+0x35/0x40 [ 14.506445] ---[ end trace 2d9633159fdc6ee7 ]---

In the Linux kernel, the following vulnerability has been resolved: rpmsg: qcom_smd: Fix refcount leak in qcom_smd_parse_edge of_parse_phandle() returns a node pointer with refcount incremented, we should use of_node_put() on it when done.

In the Linux kernel, the following vulnerability has been resolved: scsi: mpt3sas: Fix possible resource leaks in mpt3sas_transport_port_add() In mpt3sas_transport_port_add(), if sas_rphy_add() returns error, sas_rphy_free() needs be called to free the resource allocated in sas_end_device_alloc(). Otherwise a kernel crash will happen: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000108 CPU: 45 PID: 37020 Comm: bash Kdump: loaded Tainted: G W 6.1.0-rc1+ #189 pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : device_del+0x54/0x3d0 lr : device_del+0x37c/0x3d0 Call trace: device_del+0x54/0x3d0 attribute_container_class_device_del+0x28/0x38 transport_remove_classdev+0x6c/0x80 attribute_container_device_trigger+0x108/0x110 transport_remove_device+0x28/0x38 sas_rphy_remove+0x50/0x78 [scsi_transport_sas] sas_port_delete+0x30/0x148 [scsi_transport_sas] do_sas_phy_delete+0x78/0x80 [scsi_transport_sas] device_for_each_child+0x68/0xb0 sas_remove_children+0x30/0x50 [scsi_transport_sas] sas_rphy_remove+0x38/0x78 [scsi_transport_sas] sas_port_delete+0x30/0x148 [scsi_transport_sas] do_sas_phy_delete+0x78/0x80 [scsi_transport_sas] device_for_each_child+0x68/0xb0 sas_remove_children+0x30/0x50 [scsi_transport_sas] sas_remove_host+0x20/0x38 [scsi_transport_sas] scsih_remove+0xd8/0x420 [mpt3sas] Because transport_add_device() is not called when sas_rphy_add() fails, the device is not added. When sas_rphy_remove() is subsequently called to remove the device in the remove() path, a NULL pointer dereference happens.

In the Linux kernel, the following vulnerability has been resolved: powerpc/xive: Fix refcount leak in xive_get_max_prio of_find_node_by_path() returns a node pointer with refcount incremented, we should use of_node_put() on it when done. Add missing of_node_put() to avoid refcount leak.

In the Linux kernel, the following vulnerability has been resolved: tipc: fix a null-ptr-deref in tipc_topsrv_accept syzbot found a crash in tipc_topsrv_accept: KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f] Workqueue: tipc_rcv tipc_topsrv_accept RIP: 0010:kernel_accept+0x22d/0x350 net/socket.c:3487 Call Trace: <TASK> tipc_topsrv_accept+0x197/0x280 net/tipc/topsrv.c:460 process_one_work+0x991/0x1610 kernel/workqueue.c:2289 worker_thread+0x665/0x1080 kernel/workqueue.c:2436 kthread+0x2e4/0x3a0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306 It was caused by srv->listener that might be set to null by tipc_topsrv_stop() in net .exit whereas it's still used in tipc_topsrv_accept() worker. srv->listener is protected by srv->idr_lock in tipc_topsrv_stop(), so add a check for srv->listener under srv->idr_lock in tipc_topsrv_accept() to avoid the null-ptr-deref. To ensure the lsock is not released during the tipc_topsrv_accept(), move sock_release() after tipc_topsrv_work_stop() where it's waiting until the tipc_topsrv_accept worker to be done. Note that sk_callback_lock is used to protect sk->sk_user_data instead of srv->listener, and it should check srv in tipc_topsrv_listener_data_ready() instead. This also ensures that no more tipc_topsrv_accept worker will be started after tipc_conn_close() is called in tipc_topsrv_stop() where it sets sk->sk_user_data to null.

In the Linux kernel, the following vulnerability has been resolved: memstick/ms_block: Fix a memory leak 'erased_blocks_bitmap' is never freed. As it is allocated at the same time as 'used_blocks_bitmap', it is likely that it should be freed also at the same time. Add the corresponding bitmap_free() in msb_data_clear().

In the Linux kernel, the following vulnerability has been resolved: ASoC: mediatek: Assign dummy when codec not specified for a DAI link MediaTek sound card drivers are checking whether a DAI link is present and used on a board to assign the correct parameters and this is done by checking the codec DAI names at probe time. If no real codec is present, assign the dummy codec to the DAI link to avoid NULL pointer during string comparison.

In the Linux kernel, the following vulnerability has been resolved: greybus: lights: check return of get_channel_from_mode If channel for the given node is not found we return null from get_channel_from_mode. Make sure we validate the return pointer before using it in two of the missing places. This was originally reported in [0]: Found by Linux Verification Center (linuxtesting.org) with SVACE. [0] https://lore.kernel.org/all/20240301190425.120605-1-m.lobanov@rosalinux.ru

In the Linux kernel, the following vulnerability has been resolved: x86/kprobes: Update kcb status flag after singlestepping Fix kprobes to update kcb (kprobes control block) status flag to KPROBE_HIT_SSDONE even if the kp->post_handler is not set. This bug may cause a kernel panic if another INT3 user runs right after kprobes because kprobe_int3_handler() misunderstands the INT3 is kprobe's single stepping INT3.

In the Linux kernel, the following vulnerability has been resolved: serial: max3100: Lock port->lock when calling uart_handle_cts_change() uart_handle_cts_change() has to be called with port lock taken, Since we run it in a separate work, the lock may not be taken at the time of running. Make sure that it's taken by explicitly doing that. Without it we got a splat: WARNING: CPU: 0 PID: 10 at drivers/tty/serial/serial_core.c:3491 uart_handle_cts_change+0xa6/0xb0 ... Workqueue: max3100-0 max3100_work [max3100] RIP: 0010:uart_handle_cts_change+0xa6/0xb0 ... max3100_handlerx+0xc5/0x110 [max3100] max3100_work+0x12a/0x340 [max3100]

fs/splice.c in the splice subsystem in the Linux kernel before 2.6.22.2 does not properly handle a failure of the add_to_page_cache_lru function, and subsequently attempts to unlock a page that was not locked, which allows local users to cause a denial of service (kernel BUG and system crash), as demonstrated by the fio I/O tool.

In the Linux kernel, the following vulnerability has been resolved: tty: serial: Fix refcount leak bug in ucc_uart.c In soc_info(), of_find_node_by_type() will return a node pointer with refcount incremented. We should use of_node_put() when it is not used anymore.

In the Linux kernel, the following vulnerability has been resolved: ixgbe: fix pci device refcount leak As the comment of pci_get_domain_bus_and_slot() says, it returns a PCI device with refcount incremented, when finish using it, the caller must decrement the reference count by calling pci_dev_put(). In ixgbe_get_first_secondary_devfn() and ixgbe_x550em_a_has_mii(), pci_dev_put() is called to avoid leak.

In the Linux kernel, the following vulnerability has been resolved: f2fs: initialize locks earlier in f2fs_fill_super() syzbot is reporting lockdep warning at f2fs_handle_error() [1], for spin_lock(&sbi->error_lock) is called before spin_lock_init() is called. For safe locking in error handling, move initialization of locks (and obvious structures) in f2fs_fill_super() to immediately after memory allocation.

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix anon_dev leak in create_subvol() When btrfs_qgroup_inherit(), btrfs_alloc_tree_block, or btrfs_insert_root() fail in create_subvol(), we return without freeing anon_dev. Reorganize the error handling in create_subvol() to fix this.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix crash due to incorrect copy_map_value When both bpf_spin_lock and bpf_timer are present in a BPF map value, copy_map_value needs to skirt both objects when copying a value into and out of the map. However, the current code does not set both s_off and t_off in copy_map_value, which leads to a crash when e.g. bpf_spin_lock is placed in map value with bpf_timer, as bpf_map_update_elem call will be able to overwrite the other timer object. When the issue is not fixed, an overwriting can produce the following splat: [root@(none) bpf]# ./test_progs -t timer_crash [ 15.930339] bpf_testmod: loading out-of-tree module taints kernel. [ 16.037849] ================================================================== [ 16.038458] BUG: KASAN: user-memory-access in __pv_queued_spin_lock_slowpath+0x32b/0x520 [ 16.038944] Write of size 8 at addr 0000000000043ec0 by task test_progs/325 [ 16.039399] [ 16.039514] CPU: 0 PID: 325 Comm: test_progs Tainted: G OE 5.16.0+ #278 [ 16.039983] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ArchLinux 1.15.0-1 04/01/2014 [ 16.040485] Call Trace: [ 16.040645] <TASK> [ 16.040805] dump_stack_lvl+0x59/0x73 [ 16.041069] ? __pv_queued_spin_lock_slowpath+0x32b/0x520 [ 16.041427] kasan_report.cold+0x116/0x11b [ 16.041673] ? __pv_queued_spin_lock_slowpath+0x32b/0x520 [ 16.042040] __pv_queued_spin_lock_slowpath+0x32b/0x520 [ 16.042328] ? memcpy+0x39/0x60 [ 16.042552] ? pv_hash+0xd0/0xd0 [ 16.042785] ? lockdep_hardirqs_off+0x95/0xd0 [ 16.043079] __bpf_spin_lock_irqsave+0xdf/0xf0 [ 16.043366] ? bpf_get_current_comm+0x50/0x50 [ 16.043608] ? jhash+0x11a/0x270 [ 16.043848] bpf_timer_cancel+0x34/0xe0 [ 16.044119] bpf_prog_c4ea1c0f7449940d_sys_enter+0x7c/0x81 [ 16.044500] bpf_trampoline_6442477838_0+0x36/0x1000 [ 16.044836] __x64_sys_nanosleep+0x5/0x140 [ 16.045119] do_syscall_64+0x59/0x80 [ 16.045377] ? lock_is_held_type+0xe4/0x140 [ 16.045670] ? irqentry_exit_to_user_mode+0xa/0x40 [ 16.046001] ? mark_held_locks+0x24/0x90 [ 16.046287] ? asm_exc_page_fault+0x1e/0x30 [ 16.046569] ? asm_exc_page_fault+0x8/0x30 [ 16.046851] ? lockdep_hardirqs_on+0x7e/0x100 [ 16.047137] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 16.047405] RIP: 0033:0x7f9e4831718d [ 16.047602] Code: b4 0c 00 0f 05 eb a9 66 0f 1f 44 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d b3 6c 0c 00 f7 d8 64 89 01 48 [ 16.048764] RSP: 002b:00007fff488086b8 EFLAGS: 00000206 ORIG_RAX: 0000000000000023 [ 16.049275] RAX: ffffffffffffffda RBX: 00007f9e48683740 RCX: 00007f9e4831718d [ 16.049747] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00007fff488086d0 [ 16.050225] RBP: 00007fff488086f0 R08: 00007fff488085d7 R09: 00007f9e4cb594a0 [ 16.050648] R10: 0000000000000000 R11: 0000000000000206 R12: 00007f9e484cde30 [ 16.051124] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 [ 16.051608] </TASK> [ 16.051762] ==================================================================

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix netif state handling mlx5e_suspend cleans resources only if netif_device_present() returns true. However, mlx5e_resume changes the state of netif, via mlx5e_nic_enable, only if reg_state == NETREG_REGISTERED. In the below case, the above leads to NULL-ptr Oops[1] and memory leaks: mlx5e_probe _mlx5e_resume mlx5e_attach_netdev mlx5e_nic_enable <-- netdev not reg, not calling netif_device_attach() register_netdev <-- failed for some reason. ERROR_FLOW: _mlx5e_suspend <-- netif_device_present return false, resources aren't freed :( Hence, clean resources in this case as well. [1] BUG: kernel NULL pointer dereference, address: 0000000000000000 PGD 0 P4D 0 Oops: 0010 [#1] SMP CPU: 2 PID: 9345 Comm: test-ovs-ct-gen Not tainted 6.5.0_for_upstream_min_debug_2023_09_05_16_01 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:0x0 Code: Unable to access opcode bytes at0xffffffffffffffd6. RSP: 0018:ffff888178aaf758 EFLAGS: 00010246 Call Trace: <TASK> ? __die+0x20/0x60 ? page_fault_oops+0x14c/0x3c0 ? exc_page_fault+0x75/0x140 ? asm_exc_page_fault+0x22/0x30 notifier_call_chain+0x35/0xb0 blocking_notifier_call_chain+0x3d/0x60 mlx5_blocking_notifier_call_chain+0x22/0x30 [mlx5_core] mlx5_core_uplink_netdev_event_replay+0x3e/0x60 [mlx5_core] mlx5_mdev_netdev_track+0x53/0x60 [mlx5_ib] mlx5_ib_roce_init+0xc3/0x340 [mlx5_ib] __mlx5_ib_add+0x34/0xd0 [mlx5_ib] mlx5r_probe+0xe1/0x210 [mlx5_ib] ? auxiliary_match_id+0x6a/0x90 auxiliary_bus_probe+0x38/0x80 ? driver_sysfs_add+0x51/0x80 really_probe+0xc9/0x3e0 ? driver_probe_device+0x90/0x90 __driver_probe_device+0x80/0x160 driver_probe_device+0x1e/0x90 __device_attach_driver+0x7d/0x100 bus_for_each_drv+0x80/0xd0 __device_attach+0xbc/0x1f0 bus_probe_device+0x86/0xa0 device_add+0x637/0x840 __auxiliary_device_add+0x3b/0xa0 add_adev+0xc9/0x140 [mlx5_core] mlx5_rescan_drivers_locked+0x22a/0x310 [mlx5_core] mlx5_register_device+0x53/0xa0 [mlx5_core] mlx5_init_one_devl_locked+0x5c4/0x9c0 [mlx5_core] mlx5_init_one+0x3b/0x60 [mlx5_core] probe_one+0x44c/0x730 [mlx5_core] local_pci_probe+0x3e/0x90 pci_device_probe+0xbf/0x210 ? kernfs_create_link+0x5d/0xa0 ? sysfs_do_create_link_sd+0x60/0xc0 really_probe+0xc9/0x3e0 ? driver_probe_device+0x90/0x90 __driver_probe_device+0x80/0x160 driver_probe_device+0x1e/0x90 __device_attach_driver+0x7d/0x100 bus_for_each_drv+0x80/0xd0 __device_attach+0xbc/0x1f0 pci_bus_add_device+0x54/0x80 pci_iov_add_virtfn+0x2e6/0x320 sriov_enable+0x208/0x420 mlx5_core_sriov_configure+0x9e/0x200 [mlx5_core] sriov_numvfs_store+0xae/0x1a0 kernfs_fop_write_iter+0x10c/0x1a0 vfs_write+0x291/0x3c0 ksys_write+0x5f/0xe0 do_syscall_64+0x3d/0x90 entry_SYSCALL_64_after_hwframe+0x46/0xb0 CR2: 0000000000000000 ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Reload only IB representors upon lag disable/enable On lag disable, the bond IB device along with all of its representors are destroyed, and then the slaves' representors get reloaded. In case the slave IB representor load fails, the eswitch error flow unloads all representors, including ethernet representors, where the netdevs get detached and removed from lag bond. Such flow is inaccurate as the lag driver is not responsible for loading/unloading ethernet representors. Furthermore, the flow described above begins by holding lag lock to prevent bond changes during disable flow. However, when reaching the ethernet representors detachment from lag, the lag lock is required again, triggering the following deadlock: Call trace: __switch_to+0xf4/0x148 __schedule+0x2c8/0x7d0 schedule+0x50/0xe0 schedule_preempt_disabled+0x18/0x28 __mutex_lock.isra.13+0x2b8/0x570 __mutex_lock_slowpath+0x1c/0x28 mutex_lock+0x4c/0x68 mlx5_lag_remove_netdev+0x3c/0x1a0 [mlx5_core] mlx5e_uplink_rep_disable+0x70/0xa0 [mlx5_core] mlx5e_detach_netdev+0x6c/0xb0 [mlx5_core] mlx5e_netdev_change_profile+0x44/0x138 [mlx5_core] mlx5e_netdev_attach_nic_profile+0x28/0x38 [mlx5_core] mlx5e_vport_rep_unload+0x184/0x1b8 [mlx5_core] mlx5_esw_offloads_rep_load+0xd8/0xe0 [mlx5_core] mlx5_eswitch_reload_reps+0x74/0xd0 [mlx5_core] mlx5_disable_lag+0x130/0x138 [mlx5_core] mlx5_lag_disable_change+0x6c/0x70 [mlx5_core] // hold ldev->lock mlx5_devlink_eswitch_mode_set+0xc0/0x410 [mlx5_core] devlink_nl_cmd_eswitch_set_doit+0xdc/0x180 genl_family_rcv_msg_doit.isra.17+0xe8/0x138 genl_rcv_msg+0xe4/0x220 netlink_rcv_skb+0x44/0x108 genl_rcv+0x40/0x58 netlink_unicast+0x198/0x268 netlink_sendmsg+0x1d4/0x418 sock_sendmsg+0x54/0x60 __sys_sendto+0xf4/0x120 __arm64_sys_sendto+0x30/0x40 el0_svc_common+0x8c/0x120 do_el0_svc+0x30/0xa0 el0_svc+0x20/0x30 el0_sync_handler+0x90/0xb8 el0_sync+0x160/0x180 Thus, upon lag enable/disable, load and unload only the IB representors of the slaves preventing the deadlock mentioned above. While at it, refactor the mlx5_esw_offloads_rep_load() function to have a static helper method for its internal logic, in symmetry with the representor unload design.

In the Linux kernel, the following vulnerability has been resolved: ata: pata_octeon_cf: Fix refcount leak in octeon_cf_probe of_find_device_by_node() takes reference, we should use put_device() to release it when not need anymore. Add missing put_device() to avoid refcount leak.

In the Linux kernel, the following vulnerability has been resolved: wifi: ar5523: enable proper endpoint verification Syzkaller reports [1] hitting a warning about an endpoint in use not having an expected type to it. Fix the issue by checking for the existence of all proper endpoints with their according types intact. Sadly, this patch has not been tested on real hardware. [1] Syzkaller report: ------------[ cut here ]------------ usb 1-1: BOGUS urb xfer, pipe 3 != type 1 WARNING: CPU: 0 PID: 3643 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504 ... Call Trace: <TASK> ar5523_cmd+0x41b/0x780 drivers/net/wireless/ath/ar5523/ar5523.c:275 ar5523_cmd_read drivers/net/wireless/ath/ar5523/ar5523.c:302 [inline] ar5523_host_available drivers/net/wireless/ath/ar5523/ar5523.c:1376 [inline] ar5523_probe+0x14b0/0x1d10 drivers/net/wireless/ath/ar5523/ar5523.c:1655 usb_probe_interface+0x30f/0x7f0 drivers/usb/core/driver.c:396 call_driver_probe drivers/base/dd.c:560 [inline] really_probe+0x249/0xb90 drivers/base/dd.c:639 __driver_probe_device+0x1df/0x4d0 drivers/base/dd.c:778 driver_probe_device+0x4c/0x1a0 drivers/base/dd.c:808 __device_attach_driver+0x1d4/0x2e0 drivers/base/dd.c:936 bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:427 __device_attach+0x1e4/0x530 drivers/base/dd.c:1008 bus_probe_device+0x1e8/0x2a0 drivers/base/bus.c:487 device_add+0xbd9/0x1e90 drivers/base/core.c:3517 usb_set_configuration+0x101d/0x1900 drivers/usb/core/message.c:2170 usb_generic_driver_probe+0xbe/0x100 drivers/usb/core/generic.c:238 usb_probe_device+0xd8/0x2c0 drivers/usb/core/driver.c:293 call_driver_probe drivers/base/dd.c:560 [inline] really_probe+0x249/0xb90 drivers/base/dd.c:639 __driver_probe_device+0x1df/0x4d0 drivers/base/dd.c:778 driver_probe_device+0x4c/0x1a0 drivers/base/dd.c:808 __device_attach_driver+0x1d4/0x2e0 drivers/base/dd.c:936 bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:427 __device_attach+0x1e4/0x530 drivers/base/dd.c:1008 bus_probe_device+0x1e8/0x2a0 drivers/base/bus.c:487 device_add+0xbd9/0x1e90 drivers/base/core.c:3517 usb_new_device.cold+0x685/0x10ad drivers/usb/core/hub.c:2573 hub_port_connect drivers/usb/core/hub.c:5353 [inline] hub_port_connect_change drivers/usb/core/hub.c:5497 [inline] port_event drivers/usb/core/hub.c:5653 [inline] hub_event+0x26cb/0x45d0 drivers/usb/core/hub.c:5735 process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289 worker_thread+0x669/0x1090 kernel/workqueue.c:2436 kthread+0x2e8/0x3a0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306 </TASK>

In the Linux kernel, the following vulnerability has been resolved: i2c: designware: use casting of u64 in clock multiplication to avoid overflow In functions i2c_dw_scl_lcnt() and i2c_dw_scl_hcnt() may have overflow by depending on the values of the given parameters including the ic_clk. For example in our use case where ic_clk is larger than one million, multiplication of ic_clk * 4700 will result in 32 bit overflow. Add cast of u64 to the calculation to avoid multiplication overflow, and use the corresponding define for divide.

In the Linux kernel, the following vulnerability has been resolved: ipv6: Fix signed integer overflow in l2tp_ip6_sendmsg When len >= INT_MAX - transhdrlen, ulen = len + transhdrlen will be overflow. To fix, we can follow what udpv6 does and subtract the transhdrlen from the max.

In the Linux kernel, the following vulnerability has been resolved: ext4: filter out EXT4_FC_REPLAY from on-disk superblock field s_state The EXT4_FC_REPLAY bit in sbi->s_mount_state is used to indicate that we are in the middle of replay the fast commit journal. This was actually a mistake, since the sbi->s_mount_info is initialized from es->s_state. Arguably s_mount_state is misleadingly named, but the name is historical --- s_mount_state and s_state dates back to ext2. What should have been used is the ext4_{set,clear,test}_mount_flag() inline functions, which sets EXT4_MF_* bits in sbi->s_mount_flags. The problem with using EXT4_FC_REPLAY is that a maliciously corrupted superblock could result in EXT4_FC_REPLAY getting set in s_mount_state. This bypasses some sanity checks, and this can trigger a BUG() in ext4_es_cache_extent(). As a easy-to-backport-fix, filter out the EXT4_FC_REPLAY bit for now. We should eventually transition away from EXT4_FC_REPLAY to something like EXT4_MF_REPLAY.

IBM DB2 for Linux, UNIX and Windows (includes DB2 Connect Server) 10.1, 10.5, and 11.1 is vulnerable to a denial of service. Users that have both EXECUTE on PD_GET_DIAG_HIST and access to the diagnostic directory on the DB2 server can cause the instance to crash. IBM X-Force ID: 158091.

In the Linux kernel, the following vulnerability has been resolved: ASoC: ti: j721e-evm: Fix refcount leak in j721e_soc_probe_* of_parse_phandle() returns a node pointer with refcount incremented, we should use of_node_put() on it when not needed anymore. Add missing of_node_put() to avoid refcount leak.

In the Linux kernel, the following vulnerability has been resolved: net: dsa: mv88e6060: prevent crash on an unused port If the port isn't a CPU port nor a user port, 'cpu_dp' is a null pointer and a crash happened on dereferencing it in mv88e6060_setup_port(): [ 9.575872] Unable to handle kernel NULL pointer dereference at virtual address 00000014 ... [ 9.942216] mv88e6060_setup from dsa_register_switch+0x814/0xe84 [ 9.948616] dsa_register_switch from mdio_probe+0x2c/0x54 [ 9.954433] mdio_probe from really_probe.part.0+0x98/0x2a0 [ 9.960375] really_probe.part.0 from driver_probe_device+0x30/0x10c [ 9.967029] driver_probe_device from __device_attach_driver+0xb8/0x13c [ 9.973946] __device_attach_driver from bus_for_each_drv+0x90/0xe0 [ 9.980509] bus_for_each_drv from __device_attach+0x110/0x184 [ 9.986632] __device_attach from bus_probe_device+0x8c/0x94 [ 9.992577] bus_probe_device from deferred_probe_work_func+0x78/0xa8 [ 9.999311] deferred_probe_work_func from process_one_work+0x290/0x73c [ 10.006292] process_one_work from worker_thread+0x30/0x4b8 [ 10.012155] worker_thread from kthread+0xd4/0x10c [ 10.017238] kthread from ret_from_fork+0x14/0x3c