The Linux kernel before 4.15-rc8 was found to be vulnerable to a NULL pointer dereference bug in the __netlink_ns_capable() function in the net/netlink/af_netlink.c file. A local attacker could exploit this when a net namespace with a netnsid is assigned to cause a kernel panic and a denial of service.

In the Linux kernel, the following vulnerability has been resolved: sfc: fix NULL dereferences in ef100_process_design_param() Since cited commit, ef100_probe_main() and hence also ef100_check_design_params() run before efx->net_dev is created; consequently, we cannot netif_set_tso_max_size() or _segs() at this point. Move those netif calls to ef100_probe_netdev(), and also replace netif_err within the design params code with pci_err.

In the Linux kernel, the following vulnerability has been resolved: net: stmmac: fix tc flower deletion for VLAN priority Rx steering To replicate the issue:- 1) Add 1 flower filter for VLAN Priority based frame steering:- $ IFDEVNAME=eth0 $ tc qdisc add dev $IFDEVNAME ingress $ tc qdisc add dev $IFDEVNAME root mqprio num_tc 8 \ map 0 1 2 3 4 5 6 7 0 0 0 0 0 0 0 0 \ queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0 $ tc filter add dev $IFDEVNAME parent ffff: protocol 802.1Q \ flower vlan_prio 0 hw_tc 0 2) Get the 'pref' id $ tc filter show dev $IFDEVNAME ingress 3) Delete a specific tc flower record (say pref 49151) $ tc filter del dev $IFDEVNAME parent ffff: pref 49151 From dmesg, we will observe kernel NULL pointer ooops [ 197.170464] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 197.171367] #PF: supervisor read access in kernel mode [ 197.171367] #PF: error_code(0x0000) - not-present page [ 197.171367] PGD 0 P4D 0 [ 197.171367] Oops: 0000 [#1] PREEMPT SMP NOPTI <snip> [ 197.171367] RIP: 0010:tc_setup_cls+0x20b/0x4a0 [stmmac] <snip> [ 197.171367] Call Trace: [ 197.171367] <TASK> [ 197.171367] ? __stmmac_disable_all_queues+0xa8/0xe0 [stmmac] [ 197.171367] stmmac_setup_tc_block_cb+0x70/0x110 [stmmac] [ 197.171367] tc_setup_cb_destroy+0xb3/0x180 [ 197.171367] fl_hw_destroy_filter+0x94/0xc0 [cls_flower] The above issue is due to previous incorrect implementation of tc_del_vlan_flow(), shown below, that uses flow_cls_offload_flow_rule() to get struct flow_rule *rule which is no longer valid for tc filter delete operation. struct flow_rule *rule = flow_cls_offload_flow_rule(cls); struct flow_dissector *dissector = rule->match.dissector; So, to ensure tc_del_vlan_flow() deletes the right VLAN cls record for earlier configured RX queue (configured by hw_tc) in tc_add_vlan_flow(), this patch introduces stmmac_rfs_entry as driver-side flow_cls_offload record for 'RX frame steering' tc flower, currently used for VLAN priority. The implementation has taken consideration for future extension to include other type RX frame steering such as EtherType based. v2: - Clean up overly extensive backtrace and rewrite git message to better explain the kernel NULL pointer issue.

A null pointer dereference issue was found in the sctp network protocol in net/sctp/stream_sched.c in Linux Kernel. If stream_in allocation is failed, stream_out is freed which would further be accessed. A local user could use this flaw to crash the system or potentially cause a denial of service.

In the Linux kernel, the following vulnerability has been resolved: x86/resctrl: Fix allocation of cleanest CLOSID on platforms with no monitors Commit 6eac36bb9eb0 ("x86/resctrl: Allocate the cleanest CLOSID by searching closid_num_dirty_rmid") added logic that causes resctrl to search for the CLOSID with the fewest dirty cache lines when creating a new control group, if requested by the arch code. This depends on the values read from the llc_occupancy counters. The logic is applicable to architectures where the CLOSID effectively forms part of the monitoring identifier and so do not allow complete freedom to choose an unused monitoring identifier for a given CLOSID. This support missed that some platforms may not have these counters. This causes a NULL pointer dereference when creating a new control group as the array was not allocated by dom_data_init(). As this feature isn't necessary on platforms that don't have cache occupancy monitors, add this to the check that occurs when a new control group is allocated.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fixed integer types and null check locations [why]: issues fixed: - comparison with wider integer type in loop condition which can cause infinite loops - pointer dereference before null check

The crypto_skcipher_init_tfm function in crypto/skcipher.c in the Linux kernel through 4.11.2 relies on a setkey function that lacks a key-size check, which allows local users to cause a denial of service (NULL pointer dereference) via a crafted application.

NVIDIA CUDA Toolkit SDK contains a bug in cuobjdump, where a local user running the tool against an ill-formed binary may cause a null- pointer dereference, which may result in a limited denial of service.

drivers/media/platform/msm/broadcast/tsc.c in the TSC driver for the Linux kernel 3.x, as used in Qualcomm Innovation Center (QuIC) Android contributions for MSM devices and other products, allows attackers to cause a denial of service (invalid pointer dereference) or possibly have unspecified other impact via a crafted application that makes a TSC_GET_CARD_STATUS ioctl call.

The handle_invept function in arch/x86/kvm/vmx.c in the Linux kernel 3.12 through 3.15 allows privileged KVM guest OS users to cause a denial of service (NULL pointer dereference and host OS crash) via a single-context INVEPT instruction with a NULL EPT pointer.

In the Linux kernel, the following vulnerability has been resolved: driver core: fix potential NULL pointer dereference in dev_uevent() If userspace reads "uevent" device attribute at the same time as another threads unbinds the device from its driver, change to dev->driver from a valid pointer to NULL may result in crash. Fix this by using READ_ONCE() when fetching the pointer, and take bus' drivers klist lock to make sure driver instance will not disappear while we access it. Use WRITE_ONCE() when setting the driver pointer to ensure there is no tearing.

The keyring_search_aux function in security/keys/keyring.c in the Linux kernel through 3.14.79 allows local users to cause a denial of service (NULL pointer dereference and OOPS) via a request_key system call for the "dead" type.

A NULL pointer dereference flaw was found in rawv6_push_pending_frames in net/ipv6/raw.c in the network subcomponent in the Linux kernel. This flaw causes the system to crash.

Use-after-free vulnerability in fs/crypto/ in the Linux kernel before 4.10.7 allows local users to cause a denial of service (NULL pointer dereference) or possibly gain privileges by revoking keyring keys being used for ext4, f2fs, or ubifs encryption, causing cryptographic transform objects to be freed prematurely.

In the Linux kernel, the following vulnerability has been resolved: spi: spi-imx: Add check for spi_imx_setupxfer() Add check for the return value of spi_imx_setupxfer(). spi_imx->rx and spi_imx->tx function pointer can be NULL when spi_imx_setupxfer() return error, and make NULL pointer dereference. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Call trace: 0x0 spi_imx_pio_transfer+0x50/0xd8 spi_imx_transfer_one+0x18c/0x858 spi_transfer_one_message+0x43c/0x790 __spi_pump_transfer_message+0x238/0x5d4 __spi_sync+0x2b0/0x454 spi_write_then_read+0x11c/0x200

In the Linux kernel, the following vulnerability has been resolved: phy: qcom-qmp-combo: fix NULL-deref on runtime resume Commit fc64623637da ("phy: qcom-qmp-combo,usb: add support for separate PCS_USB region") started treating the PCS_USB registers as potentially separate from the PCS registers but used the wrong base when no PCS_USB offset has been provided. Fix the PCS_USB base used at runtime resume to prevent dereferencing a NULL pointer on platforms that do not provide a PCS_USB offset (e.g. SC7180).

In the Linux kernel, the following vulnerability has been resolved: x86/sgx: Resolves SECS reclaim vs. page fault for EAUG race The SGX EPC reclaimer (ksgxd) may reclaim the SECS EPC page for an enclave and set secs.epc_page to NULL. The SECS page is used for EAUG and ELDU in the SGX page fault handler. However, the NULL check for secs.epc_page is only done for ELDU, not EAUG before being used. Fix this by doing the same NULL check and reloading of the SECS page as needed for both EAUG and ELDU. The SECS page holds global enclave metadata. It can only be reclaimed when there are no other enclave pages remaining. At that point, virtually nothing can be done with the enclave until the SECS page is paged back in. An enclave can not run nor generate page faults without a resident SECS page. But it is still possible for a #PF for a non-SECS page to race with paging out the SECS page: when the last resident non-SECS page A triggers a #PF in a non-resident page B, and then page A and the SECS both are paged out before the #PF on B is handled. Hitting this bug requires that race triggered with a #PF for EAUG. Following is a trace when it happens. BUG: kernel NULL pointer dereference, address: 0000000000000000 RIP: 0010:sgx_encl_eaug_page+0xc7/0x210 Call Trace: ? __kmem_cache_alloc_node+0x16a/0x440 ? xa_load+0x6e/0xa0 sgx_vma_fault+0x119/0x230 __do_fault+0x36/0x140 do_fault+0x12f/0x400 __handle_mm_fault+0x728/0x1110 handle_mm_fault+0x105/0x310 do_user_addr_fault+0x1ee/0x750 ? __this_cpu_preempt_check+0x13/0x20 exc_page_fault+0x76/0x180 asm_exc_page_fault+0x27/0x30

In the Linux kernel, the following vulnerability has been resolved: iommu/arm-smmu-v3: check return value after calling platform_get_resource() It will cause null-ptr-deref if platform_get_resource() returns NULL, we need check the return value.

In the Linux kernel, the following vulnerability has been resolved: pinctrl: aspeed: Fix potential NULL dereference in aspeed_pinmux_set_mux() pdesc could be null but still dereference pdesc->name and it will lead to a null pointer access. So we move a null check before dereference.

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Address NULL pointer dereference after starget_to_rport() Calls to starget_to_rport() may return NULL. Add check for NULL rport before dereference.

In the Linux kernel, the following vulnerability has been resolved: reset: uniphier-glue: Fix possible null-ptr-deref It will cause null-ptr-deref when resource_size(res) invoked, if platform_get_resource() returns NULL.

In the Linux kernel, the following vulnerability has been resolved: drm/panel: ili9341: fix optional regulator handling If the optional regulator lookup fails, reset the pointer to NULL. Other functions such as mipi_dbi_poweron_reset_conditional() only do a NULL pointer check and will otherwise dereference the error pointer.

In the Linux kernel, the following vulnerability has been resolved: vduse: Fix NULL pointer dereference on sysfs access The control device has no drvdata. So we will get a NULL pointer dereference when accessing control device's msg_timeout attribute via sysfs: [ 132.841881][ T3644] BUG: kernel NULL pointer dereference, address: 00000000000000f8 [ 132.850619][ T3644] RIP: 0010:msg_timeout_show (drivers/vdpa/vdpa_user/vduse_dev.c:1271) [ 132.869447][ T3644] dev_attr_show (drivers/base/core.c:2094) [ 132.870215][ T3644] sysfs_kf_seq_show (fs/sysfs/file.c:59) [ 132.871164][ T3644] ? device_remove_bin_file (drivers/base/core.c:2088) [ 132.872082][ T3644] kernfs_seq_show (fs/kernfs/file.c:164) [ 132.872838][ T3644] seq_read_iter (fs/seq_file.c:230) [ 132.873578][ T3644] ? __vmalloc_area_node (mm/vmalloc.c:3041) [ 132.874532][ T3644] kernfs_fop_read_iter (fs/kernfs/file.c:238) [ 132.875513][ T3644] __kernel_read (fs/read_write.c:440 (discriminator 1)) [ 132.876319][ T3644] kernel_read (fs/read_write.c:459) [ 132.877129][ T3644] kernel_read_file (fs/kernel_read_file.c:94) [ 132.877978][ T3644] kernel_read_file_from_fd (include/linux/file.h:45 fs/kernel_read_file.c:186) [ 132.879019][ T3644] __do_sys_finit_module (kernel/module.c:4207) [ 132.879930][ T3644] __ia32_sys_finit_module (kernel/module.c:4189) [ 132.880930][ T3644] do_int80_syscall_32 (arch/x86/entry/common.c:112 arch/x86/entry/common.c:132) [ 132.881847][ T3644] entry_INT80_compat (arch/x86/entry/entry_64_compat.S:419) To fix it, don't create the unneeded attribute for control device anymore.

In the Linux kernel, the following vulnerability has been resolved: drm/rockchip: vop: fix possible null-ptr-deref in vop_bind() It will cause null-ptr-deref in resource_size(), if platform_get_resource() returns NULL, move calling resource_size() after devm_ioremap_resource() that will check 'res' to avoid null-ptr-deref.

In the Linux kernel, the following vulnerability has been resolved: drm/omap: fix NULL but dereferenced coccicheck error Fix the following coccicheck warning: ./drivers/gpu/drm/omapdrm/omap_overlay.c:89:22-25: ERROR: r_ovl is NULL but dereferenced. Here should be ovl->idx rather than r_ovl->idx.

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Fix NULL pointer dereference in svm_migrate_to_ram() ./drivers/gpu/drm/amd/amdkfd/kfd_migrate.c:985:58-62: ERROR: p is NULL but dereferenced.

In the Linux kernel, the following vulnerability has been resolved: can: af_can: fix NULL pointer dereference in can_rx_register() It causes NULL pointer dereference when testing as following: (a) use syscall(__NR_socket, 0x10ul, 3ul, 0) to create netlink socket. (b) use syscall(__NR_sendmsg, ...) to create bond link device and vxcan link device, and bind vxcan device to bond device (can also use ifenslave command to bind vxcan device to bond device). (c) use syscall(__NR_socket, 0x1dul, 3ul, 1) to create CAN socket. (d) use syscall(__NR_bind, ...) to bind the bond device to CAN socket. The bond device invokes the can-raw protocol registration interface to receive CAN packets. However, ml_priv is not allocated to the dev, dev_rcv_lists is assigned to NULL in can_rx_register(). In this case, it will occur the NULL pointer dereference issue. The following is the stack information: BUG: kernel NULL pointer dereference, address: 0000000000000008 PGD 122a4067 P4D 122a4067 PUD 1223c067 PMD 0 Oops: 0000 [#1] PREEMPT SMP RIP: 0010:can_rx_register+0x12d/0x1e0 Call Trace: <TASK> raw_enable_filters+0x8d/0x120 raw_enable_allfilters+0x3b/0x130 raw_bind+0x118/0x4f0 __sys_bind+0x163/0x1a0 __x64_sys_bind+0x1e/0x30 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x63/0xcd </TASK>

In the Linux kernel, the following vulnerability has been resolved: i2c: dev: check return value when calling dev_set_name() If dev_set_name() fails, the dev_name() is null, check the return value of dev_set_name() to avoid the null-ptr-deref.

In the Linux kernel, the following vulnerability has been resolved: staging: vchiq_arm: Avoid NULL ptr deref in vchiq_dump_platform_instances vchiq_get_state() can return a NULL pointer. So handle this cases and avoid a NULL pointer derefence in vchiq_dump_platform_instances.

The xfs_dinode_verify function in fs/xfs/libxfs/xfs_inode_buf.c in the Linux kernel through 4.16.3 allows local users to cause a denial of service (xfs_ilock_attr_map_shared invalid pointer dereference) via a crafted xfs image.

The Linux Kernel versions 4.14, 4.15, and 4.16 has a null pointer dereference which can result in an out of memory (OOM) killing of large mlocked processes. The issue arises from an oom killed process's final thread calling exit_mmap(), which calls munlock_vma_pages_all() for mlocked vmas.This can happen synchronously with the oom reaper's unmap_page_range() since the vma's VM_LOCKED bit is cleared before munlocking (to determine if any other vmas share the memory and are mlocked).

In the Linux kernel, the following vulnerability has been resolved: phy: usb: sunplus: Fix potential null-ptr-deref in sp_usb_phy_probe() sp_usb_phy_probe() will call platform_get_resource_byname() that may fail and return NULL. devm_ioremap() will use usbphy->moon4_res_mem->start as input, which may causes null-ptr-deref. Check the ret value of platform_get_resource_byname() to avoid the null-ptr-deref.

In the Linux kernel, the following vulnerability has been resolved: ata: libata-core: fix NULL pointer deref in ata_host_alloc_pinfo() In an unlikely (and probably wrong?) case that the 'ppi' parameter of ata_host_alloc_pinfo() points to an array starting with a NULL pointer, there's going to be a kernel oops as the 'pi' local variable won't get reassigned from the initial value of NULL. Initialize 'pi' instead to '&ata_dummy_port_info' to fix the possible kernel oops for good... Found by Linux Verification Center (linuxtesting.org) with the SVACE static analysis tool.

Transmit requests in Xen's virtual network protocol can consist of multiple parts. While not really useful, except for the initial part any of them may be of zero length, i.e. carry no data at all. Besides a certain initial portion of the to be transferred data, these parts are directly translated into what Linux calls SKB fragments. Such converted request parts can, when for a particular SKB they are all of length zero, lead to a de-reference of NULL in core networking code.

In the Linux kernel, the following vulnerability has been resolved: net: phy: micrel: Allow probing without .driver_data Currently, if the .probe element is present in the phy_driver structure and the .driver_data is not, a NULL pointer dereference happens. Allow passing .probe without .driver_data by inserting NULL checks for priv->type.

In the Linux kernel, the following vulnerability has been resolved: hwrng: cavium - fix NULL but dereferenced coccicheck error Fix following coccicheck warning: ./drivers/char/hw_random/cavium-rng-vf.c:182:17-20: ERROR: pdev is NULL but dereferenced.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link When using a fixed-link, the altr_tse_pcs driver crashes due to null-pointer dereference as no phy_device is provided to tse_pcs_fix_mac_speed function. Fix this by adding a check for phy_dev before calling the tse_pcs_fix_mac_speed() function. Also clean up the tse_pcs_fix_mac_speed function a bit. There is no need to check for splitter_base and sgmii_adapter_base because the driver will fail if these 2 variables are not derived from the device tree.

kernel/trace/trace_syscalls.c in the Linux kernel through 3.17.2 does not properly handle private syscall numbers during use of the ftrace subsystem, which allows local users to gain privileges or cause a denial of service (invalid pointer dereference) via a crafted application.

In the Linux kernel, the following vulnerability has been resolved: media: venus: hfi: avoid null dereference in deinit If venus_probe fails at pm_runtime_put_sync the error handling first calls hfi_destroy and afterwards hfi_core_deinit. As hfi_destroy sets core->ops to NULL, hfi_core_deinit cannot call the core_deinit function anymore. Avoid this null pointer derefence by skipping the call when necessary.

In the Linux kernel, the following vulnerability has been resolved: IB/hfi1: Correctly move list in sc_disable() Commit 13bac861952a ("IB/hfi1: Fix abba locking issue with sc_disable()") incorrectly tries to move a list from one list head to another. The result is a kernel crash. The crash is triggered when a link goes down and there are waiters for a send to complete. The following signature is seen: BUG: kernel NULL pointer dereference, address: 0000000000000030 [...] Call Trace: sc_disable+0x1ba/0x240 [hfi1] pio_freeze+0x3d/0x60 [hfi1] handle_freeze+0x27/0x1b0 [hfi1] process_one_work+0x1b0/0x380 ? process_one_work+0x380/0x380 worker_thread+0x30/0x360 ? process_one_work+0x380/0x380 kthread+0xd7/0x100 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x1f/0x30 The fix is to use the correct call to move the list.

In the Linux kernel before 6.5.9, there is a NULL pointer dereference in send_acknowledge in net/nfc/nci/spi.c.

In the Linux kernel, the following vulnerability has been resolved: soc: ti: ti_sci_pm_domains: Check for null return of devm_kcalloc The allocation funciton devm_kcalloc may fail and return a null pointer, which would cause a null-pointer dereference later. It might be better to check it and directly return -ENOMEM just like the usage of devm_kcalloc in previous code.

In the Linux kernel, the following vulnerability has been resolved: drm/msm: Fix null pointer dereferences without iommu Check if 'aspace' is set before using it as it will stay null without IOMMU, such as on msm8974.

In the Linux kernel, the following vulnerability has been resolved: tipc: move bc link creation back to tipc_node_create Shuang Li reported a NULL pointer dereference crash: [] BUG: kernel NULL pointer dereference, address: 0000000000000068 [] RIP: 0010:tipc_link_is_up+0x5/0x10 [tipc] [] Call Trace: [] <IRQ> [] tipc_bcast_rcv+0xa2/0x190 [tipc] [] tipc_node_bc_rcv+0x8b/0x200 [tipc] [] tipc_rcv+0x3af/0x5b0 [tipc] [] tipc_udp_recv+0xc7/0x1e0 [tipc] It was caused by the 'l' passed into tipc_bcast_rcv() is NULL. When it creates a node in tipc_node_check_dest(), after inserting the new node into hashtable in tipc_node_create(), it creates the bc link. However, there is a gap between this insert and bc link creation, a bc packet may come in and get the node from the hashtable then try to dereference its bc link, which is NULL. This patch is to fix it by moving the bc link creation before inserting into the hashtable. Note that for a preliminary node becoming "real", the bc link creation should also be called before it's rehashed, as we don't create it for preliminary nodes.

In the Linux kernel, the following vulnerability has been resolved: scsi: scsi_transport_sas: Fix error handling in sas_phy_add() If transport_add_device() fails in sas_phy_add(), the kernel will crash trying to delete the device in transport_remove_device() called from sas_remove_host(). Unable to handle kernel NULL pointer dereference at virtual address 0000000000000108 CPU: 61 PID: 42829 Comm: rmmod Kdump: loaded Tainted: G W 6.1.0-rc1+ #173 pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : device_del+0x54/0x3d0 lr : device_del+0x37c/0x3d0 Call trace: device_del+0x54/0x3d0 attribute_container_class_device_del+0x28/0x38 transport_remove_classdev+0x6c/0x80 attribute_container_device_trigger+0x108/0x110 transport_remove_device+0x28/0x38 sas_phy_delete+0x30/0x60 [scsi_transport_sas] do_sas_phy_delete+0x6c/0x80 [scsi_transport_sas] device_for_each_child+0x68/0xb0 sas_remove_children+0x40/0x50 [scsi_transport_sas] sas_remove_host+0x20/0x38 [scsi_transport_sas] hisi_sas_remove+0x40/0x68 [hisi_sas_main] hisi_sas_v2_remove+0x20/0x30 [hisi_sas_v2_hw] platform_remove+0x2c/0x60 Fix this by checking and handling return value of transport_add_device() in sas_phy_add().

In the Linux kernel, the following vulnerability has been resolved: net: dsa: fix NULL pointer dereference in dsa_port_reset_vlan_filtering The "ds" iterator variable used in dsa_port_reset_vlan_filtering() -> dsa_switch_for_each_port() overwrites the "dp" received as argument, which is later used to call dsa_port_vlan_filtering() proper. As a result, switches which do enter that code path (the ones with vlan_filtering_is_global=true) will dereference an invalid dp in dsa_port_reset_vlan_filtering() after leaving a VLAN-aware bridge. Use a dedicated "other_dp" iterator variable to avoid this from happening.

In the Linux kernel, the following vulnerability has been resolved: tty: synclink_gt: Fix null-pointer-dereference in slgt_clean() When the driver fails at alloc_hdlcdev(), and then we remove the driver module, we will get the following splat: [ 25.065966] general protection fault, probably for non-canonical address 0xdffffc0000000182: 0000 [#1] PREEMPT SMP KASAN PTI [ 25.066914] KASAN: null-ptr-deref in range [0x0000000000000c10-0x0000000000000c17] [ 25.069262] RIP: 0010:detach_hdlc_protocol+0x2a/0x3e0 [ 25.077709] Call Trace: [ 25.077924] <TASK> [ 25.078108] unregister_hdlc_device+0x16/0x30 [ 25.078481] slgt_cleanup+0x157/0x9f0 [synclink_gt] Fix this by checking whether the 'info->netdev' is a null pointer first.

In the Linux kernel, the following vulnerability has been resolved: scsi: ibmvfc: Store vhost pointer during subcrq allocation Currently the back pointer from a queue to the vhost adapter isn't set until after subcrq interrupt registration. The value is available when a queue is first allocated and can/should be also set for primary and async queues as well as subcrqs. This fixes a crash observed during kexec/kdump on Power 9 with legacy XICS interrupt controller where a pending subcrq interrupt from the previous kernel can be replayed immediately upon IRQ registration resulting in dereference of a garbage backpointer in ibmvfc_interrupt_scsi(). Kernel attempted to read user page (58) - exploit attempt? (uid: 0) BUG: Kernel NULL pointer dereference on read at 0x00000058 Faulting instruction address: 0xc008000003216a08 Oops: Kernel access of bad area, sig: 11 [#1] ... NIP [c008000003216a08] ibmvfc_interrupt_scsi+0x40/0xb0 [ibmvfc] LR [c0000000082079e8] __handle_irq_event_percpu+0x98/0x270 Call Trace: [c000000047fa3d80] [c0000000123e6180] 0xc0000000123e6180 (unreliable) [c000000047fa3df0] [c0000000082079e8] __handle_irq_event_percpu+0x98/0x270 [c000000047fa3ea0] [c000000008207d18] handle_irq_event+0x98/0x188 [c000000047fa3ef0] [c00000000820f564] handle_fasteoi_irq+0xc4/0x310 [c000000047fa3f40] [c000000008205c60] generic_handle_irq+0x50/0x80 [c000000047fa3f60] [c000000008015c40] __do_irq+0x70/0x1a0 [c000000047fa3f90] [c000000008016d7c] __do_IRQ+0x9c/0x130 [c000000014622f60] [0000000020000000] 0x20000000 [c000000014622ff0] [c000000008016e50] do_IRQ+0x40/0xa0 [c000000014623020] [c000000008017044] replay_soft_interrupts+0x194/0x2f0 [c000000014623210] [c0000000080172a8] arch_local_irq_restore+0x108/0x170 [c000000014623240] [c000000008eb1008] _raw_spin_unlock_irqrestore+0x58/0xb0 [c000000014623270] [c00000000820b12c] __setup_irq+0x49c/0x9f0 [c000000014623310] [c00000000820b7c0] request_threaded_irq+0x140/0x230 [c000000014623380] [c008000003212a50] ibmvfc_register_scsi_channel+0x1e8/0x2f0 [ibmvfc] [c000000014623450] [c008000003213d1c] ibmvfc_init_sub_crqs+0xc4/0x1f0 [ibmvfc] [c0000000146234d0] [c0080000032145a8] ibmvfc_reset_crq+0x150/0x210 [ibmvfc] [c000000014623550] [c0080000032147c8] ibmvfc_init_crq+0x160/0x280 [ibmvfc] [c0000000146235f0] [c00800000321a9cc] ibmvfc_probe+0x2a4/0x530 [ibmvfc]

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: fix general-protection-fault in ieee80211_subif_start_xmit() When device is running and the interface status is changed, the gpf issue is triggered. The problem triggering process is as follows: Thread A: Thread B ieee80211_runtime_change_iftype() process_one_work() ... ... ieee80211_do_stop() ... ... ... sdata->bss = NULL ... ... ieee80211_subif_start_xmit() ieee80211_multicast_to_unicast //!sdata->bss->multicast_to_unicast cause gpf issue When the interface status is changed, the sending queue continues to send packets. After the bss is set to NULL, the bss is accessed. As a result, this causes a general-protection-fault issue. The following is the stack information: general protection fault, probably for non-canonical address 0xdffffc000000002f: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000178-0x000000000000017f] Workqueue: mld mld_ifc_work RIP: 0010:ieee80211_subif_start_xmit+0x25b/0x1310 Call Trace: <TASK> dev_hard_start_xmit+0x1be/0x990 __dev_queue_xmit+0x2c9a/0x3b60 ip6_finish_output2+0xf92/0x1520 ip6_finish_output+0x6af/0x11e0 ip6_output+0x1ed/0x540 mld_sendpack+0xa09/0xe70 mld_ifc_work+0x71c/0xdb0 process_one_work+0x9bf/0x1710 worker_thread+0x665/0x1080 kthread+0x2e4/0x3a0 ret_from_fork+0x1f/0x30 </TASK>

In the Linux kernel, the following vulnerability has been resolved: thermal/drivers/broadcom: Fix potential NULL dereference in sr_thermal_probe platform_get_resource() may return NULL, add proper check to avoid potential NULL dereferencing.