In the Linux kernel, the following vulnerability has been resolved: phy: qcom: qmp-usb: fix NULL-deref on runtime suspend Commit 413db06c05e7 ("phy: qcom-qmp-usb: clean up probe initialisation") removed most users of the platform device driver data, but mistakenly also removed the initialisation despite the data still being used in the runtime PM callbacks. Restore the driver data initialisation at probe to avoid a NULL-pointer dereference on runtime suspend. Apparently no one uses runtime PM, which currently needs to be enabled manually through sysfs, with this driver.

In the Linux kernel, the following vulnerability has been resolved: ceph: remove the incorrect Fw reference check when dirtying pages When doing the direct-io reads it will also try to mark pages dirty, but for the read path it won't hold the Fw caps and there is case will it get the Fw reference.

In the Linux kernel, the following vulnerability has been resolved: ASoC: stm32: spdifrx: fix dma channel release in stm32_spdifrx_remove In case of error when requesting ctrl_chan DMA channel, ctrl_chan is not null. So the release of the dma channel leads to the following issue: [ 4.879000] st,stm32-spdifrx 500d0000.audio-controller: dma_request_slave_channel error -19 [ 4.888975] Unable to handle kernel NULL pointer dereference at virtual address 000000000000003d [...] [ 5.096577] Call trace: [ 5.099099] dma_release_channel+0x24/0x100 [ 5.103235] stm32_spdifrx_remove+0x24/0x60 [snd_soc_stm32_spdifrx] [ 5.109494] stm32_spdifrx_probe+0x320/0x4c4 [snd_soc_stm32_spdifrx] To avoid this issue, release channel only if the pointer is valid.

A use-after-free vulnerabilitity was discovered in drivers/net/hamradio/6pack.c of linux that allows an attacker to crash linux kernel by simulating ax25 device using 6pack driver from user space.

In the Linux kernel, the following vulnerability has been resolved: RDMA/bnxt_re: Fix a possible memory leak In bnxt_re_setup_chip_ctx() when bnxt_qplib_map_db_bar() fails driver is not freeing the memory allocated for "rdev->chip_ctx".

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Initialize denominators' default to 1 [WHAT & HOW] Variables used as denominators and maybe not assigned to other values, should not be 0. Change their default to 1 so they are never 0. This fixes 10 DIVIDE_BY_ZERO issues reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: posix-clock: Fix missing timespec64 check in pc_clock_settime() As Andrew pointed out, it will make sense that the PTP core checked timespec64 struct's tv_sec and tv_nsec range before calling ptp->info->settime64(). As the man manual of clock_settime() said, if tp.tv_sec is negative or tp.tv_nsec is outside the range [0..999,999,999], it should return EINVAL, which include dynamic clocks which handles PTP clock, and the condition is consistent with timespec64_valid(). As Thomas suggested, timespec64_valid() only check the timespec is valid, but not ensure that the time is in a valid range, so check it ahead using timespec64_valid_strict() in pc_clock_settime() and return -EINVAL if not valid. There are some drivers that use tp->tv_sec and tp->tv_nsec directly to write registers without validity checks and assume that the higher layer has checked it, which is dangerous and will benefit from this, such as hclge_ptp_settime(), igb_ptp_settime_i210(), _rcar_gen4_ptp_settime(), and some drivers can remove the checks of itself.

In the Linux kernel, the following vulnerability has been resolved: ext4: update orig_path in ext4_find_extent() In ext4_find_extent(), if the path is not big enough, we free it and set *orig_path to NULL. But after reallocating and successfully initializing the path, we don't update *orig_path, in which case the caller gets a valid path but a NULL ppath, and this may cause a NULL pointer dereference or a path memory leak. For example: ext4_split_extent path = *ppath = 2000 ext4_find_extent if (depth > path[0].p_maxdepth) kfree(path = 2000); *orig_path = path = NULL; path = kcalloc() = 3000 ext4_split_extent_at(*ppath = NULL) path = *ppath; ex = path[depth].p_ext; // NULL pointer dereference! ================================================================== BUG: kernel NULL pointer dereference, address: 0000000000000010 CPU: 6 UID: 0 PID: 576 Comm: fsstress Not tainted 6.11.0-rc2-dirty #847 RIP: 0010:ext4_split_extent_at+0x6d/0x560 Call Trace: <TASK> ext4_split_extent.isra.0+0xcb/0x1b0 ext4_ext_convert_to_initialized+0x168/0x6c0 ext4_ext_handle_unwritten_extents+0x325/0x4d0 ext4_ext_map_blocks+0x520/0xdb0 ext4_map_blocks+0x2b0/0x690 ext4_iomap_begin+0x20e/0x2c0 [...] ================================================================== Therefore, *orig_path is updated when the extent lookup succeeds, so that the caller can safely use path or *ppath.

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Fix shift-out-of-bounds bug Fix a shift-out-of-bounds bug reported by UBSAN when running VM with MTE enabled host kernel. UBSAN: shift-out-of-bounds in arch/arm64/kvm/sys_regs.c:1988:14 shift exponent 33 is too large for 32-bit type 'int' CPU: 26 UID: 0 PID: 7629 Comm: qemu-kvm Not tainted 6.12.0-rc2 #34 Hardware name: IEI NF5280R7/Mitchell MB, BIOS 00.00. 2024-10-12 09:28:54 10/14/2024 Call trace: dump_backtrace+0xa0/0x128 show_stack+0x20/0x38 dump_stack_lvl+0x74/0x90 dump_stack+0x18/0x28 __ubsan_handle_shift_out_of_bounds+0xf8/0x1e0 reset_clidr+0x10c/0x1c8 kvm_reset_sys_regs+0x50/0x1c8 kvm_reset_vcpu+0xec/0x2b0 __kvm_vcpu_set_target+0x84/0x158 kvm_vcpu_set_target+0x138/0x168 kvm_arch_vcpu_ioctl_vcpu_init+0x40/0x2b0 kvm_arch_vcpu_ioctl+0x28c/0x4b8 kvm_vcpu_ioctl+0x4bc/0x7a8 __arm64_sys_ioctl+0xb4/0x100 invoke_syscall+0x70/0x100 el0_svc_common.constprop.0+0x48/0xf0 do_el0_svc+0x24/0x38 el0_svc+0x3c/0x158 el0t_64_sync_handler+0x120/0x130 el0t_64_sync+0x194/0x198

In the Linux kernel, the following vulnerability has been resolved: fsl/fman: Fix refcount handling of fman-related devices In mac_probe() there are multiple calls to of_find_device_by_node(), fman_bind() and fman_port_bind() which takes references to of_dev->dev. Not all references taken by these calls are released later on error path in mac_probe() and in mac_remove() which lead to reference leaks. Add references release.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Implement bounds check for stream encoder creation in DCN401 'stream_enc_regs' array is an array of dcn10_stream_enc_registers structures. The array is initialized with four elements, corresponding to the four calls to stream_enc_regs() in the array initializer. This means that valid indices for this array are 0, 1, 2, and 3. The error message 'stream_enc_regs' 4 <= 5 below, is indicating that there is an attempt to access this array with an index of 5, which is out of bounds. This could lead to undefined behavior Here, eng_id is used as an index to access the stream_enc_regs array. If eng_id is 5, this would result in an out-of-bounds access on the stream_enc_regs array. Thus fixing Buffer overflow error in dcn401_stream_encoder_create Found by smatch: drivers/gpu/drm/amd/amdgpu/../display/dc/resource/dcn401/dcn401_resource.c:1209 dcn401_stream_encoder_create() error: buffer overflow 'stream_enc_regs' 4 <= 5

In the Linux kernel, the following vulnerability has been resolved: reset: starfive: jh71x0: Fix accessing the empty member on JH7110 SoC data->asserted will be NULL on JH7110 SoC since commit 82327b127d41 ("reset: starfive: Add StarFive JH7110 reset driver") was added. Add the judgment condition to avoid errors when calling reset_control_status on JH7110 SoC.

In the Linux kernel, the following vulnerability has been resolved: block: fix integer overflow in BLKSECDISCARD I independently rediscovered commit 22d24a544b0d49bbcbd61c8c0eaf77d3c9297155 block: fix overflow in blk_ioctl_discard() but for secure erase. Same problem: uint64_t r[2] = {512, 18446744073709551104ULL}; ioctl(fd, BLKSECDISCARD, r); will enter near infinite loop inside blkdev_issue_secure_erase(): a.out: attempt to access beyond end of device loop0: rw=5, sector=3399043073, nr_sectors = 1024 limit=2048 bio_check_eod: 3286214 callbacks suppressed

In the Linux kernel, the following vulnerability has been resolved: NFSD: Initialize struct nfsd4_copy earlier Ensure the refcount and async_copies fields are initialized early. cleanup_async_copy() will reference these fields if an error occurs in nfsd4_copy(). If they are not correctly initialized, at the very least, a refcount underflow occurs.

In the Linux kernel, the following vulnerability has been resolved: exfat: fix memory leak in exfat_load_bitmap() If the first directory entry in the root directory is not a bitmap directory entry, 'bh' will not be released and reassigned, which will cause a memory leak.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/pm: fix a potential gpu_metrics_table memory leak Memory is allocated for gpu_metrics_table in renoir_init_smc_tables(), but not freed in int smu_v12_0_fini_smc_tables(). Free it!

In the Linux kernel, the following vulnerability has been resolved: scsi: fnic: Move flush_work initialization out of if block After commit 379a58caa199 ("scsi: fnic: Move fnic_fnic_flush_tx() to a work queue"), it can happen that a work item is sent to an uninitialized work queue. This may has the effect that the item being queued is never actually queued, and any further actions depending on it will not proceed. The following warning is observed while the fnic driver is loaded: kernel: WARNING: CPU: 11 PID: 0 at ../kernel/workqueue.c:1524 __queue_work+0x373/0x410 kernel: <IRQ> kernel: queue_work_on+0x3a/0x50 kernel: fnic_wq_copy_cmpl_handler+0x54a/0x730 [fnic 62fbff0c42e7fb825c60a55cde2fb91facb2ed24] kernel: fnic_isr_msix_wq_copy+0x2d/0x60 [fnic 62fbff0c42e7fb825c60a55cde2fb91facb2ed24] kernel: __handle_irq_event_percpu+0x36/0x1a0 kernel: handle_irq_event_percpu+0x30/0x70 kernel: handle_irq_event+0x34/0x60 kernel: handle_edge_irq+0x7e/0x1a0 kernel: __common_interrupt+0x3b/0xb0 kernel: common_interrupt+0x58/0xa0 kernel: </IRQ> It has been observed that this may break the rediscovery of Fibre Channel devices after a temporary fabric failure. This patch fixes it by moving the work queue initialization out of an if block in fnic_probe().

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Deallocate DML memory if allocation fails [Why] When DC state create DML memory allocation fails, memory is not deallocated subsequently, resulting in uninitialized structure that is not NULL. [How] Deallocate memory if DML memory allocation fails.

In the Linux kernel, the following vulnerability has been resolved: zram: free secondary algorithms names We need to kfree() secondary algorithms names when reset zram device that had multi-streams, otherwise we leak memory. [senozhatsky@chromium.org: kfree(NULL) is legal]

In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: Fix memcpy() field-spanning write warning in mwifiex_cmd_802_11_scan_ext() Replace one-element array with a flexible-array member in `struct host_cmd_ds_802_11_scan_ext`. With this, fix the following warning: elo 16 17:51:58 surfacebook kernel: ------------[ cut here ]------------ elo 16 17:51:58 surfacebook kernel: memcpy: detected field-spanning write (size 243) of single field "ext_scan->tlv_buffer" at drivers/net/wireless/marvell/mwifiex/scan.c:2239 (size 1) elo 16 17:51:58 surfacebook kernel: WARNING: CPU: 0 PID: 498 at drivers/net/wireless/marvell/mwifiex/scan.c:2239 mwifiex_cmd_802_11_scan_ext+0x83/0x90 [mwifiex]

In the Linux kernel, the following vulnerability has been resolved: scsi: wd33c93: Don't use stale scsi_pointer value A regression was introduced with commit dbb2da557a6a ("scsi: wd33c93: Move the SCSI pointer to private command data") which results in an oops in wd33c93_intr(). That commit added the scsi_pointer variable and initialized it from hostdata->connected. However, during selection, hostdata->connected is not yet valid. Fix this by getting the current scsi_pointer from hostdata->selecting.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check stream_status before it is used [WHAT & HOW] dc_state_get_stream_status can return null, and therefore null must be checked before stream_status is used. This fixes 1 NULL_RETURNS issue reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: pinctrl: stm32: check devm_kasprintf() returned value devm_kasprintf() can return a NULL pointer on failure but this returned value is not checked. Fix this lack and check the returned value. Found by code review.

In the Linux kernel, the following vulnerability has been resolved: tpm: Clean up TPM space after command failure tpm_dev_transmit prepares the TPM space before attempting command transmission. However if the command fails no rollback of this preparation is done. This can result in transient handles being leaked if the device is subsequently closed with no further commands performed. Fix this by flushing the space in the event of command transmission failure.

In the Linux kernel, the following vulnerability has been resolved: HID: core: zero-initialize the report buffer Since the report buffer is used by all kinds of drivers in various ways, let's zero-initialize it during allocation to make sure that it can't be ever used to leak kernel memory via specially-crafted report.

In the Linux kernel, the following vulnerability has been resolved: thermal: core: Reference count the zone in thermal_zone_get_by_id() There are places in the thermal netlink code where nothing prevents the thermal zone object from going away while being accessed after it has been returned by thermal_zone_get_by_id(). To address this, make thermal_zone_get_by_id() get a reference on the thermal zone device object to be returned with the help of get_device(), under thermal_list_lock, and adjust all of its callers to this change with the help of the cleanup.h infrastructure.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/hdcp: Check GSC structure validity Sometimes xe_gsc is not initialized when checked at HDCP capability check. Add gsc structure check to avoid null pointer error.

In the Linux kernel, the following vulnerability has been resolved: net: fix crash when config small gso_max_size/gso_ipv4_max_size Config a small gso_max_size/gso_ipv4_max_size will lead to an underflow in sk_dst_gso_max_size(), which may trigger a BUG_ON crash, because sk->sk_gso_max_size would be much bigger than device limits. Call Trace: tcp_write_xmit tso_segs = tcp_init_tso_segs(skb, mss_now); tcp_set_skb_tso_segs tcp_skb_pcount_set // skb->len = 524288, mss_now = 8 // u16 tso_segs = 524288/8 = 65535 -> 0 tso_segs = DIV_ROUND_UP(skb->len, mss_now) BUG_ON(!tso_segs) Add check for the minimum value of gso_max_size and gso_ipv4_max_size.

In the Linux kernel, the following vulnerability has been resolved: NFSD: Limit the number of concurrent async COPY operations Nothing appears to limit the number of concurrent async COPY operations that clients can start. In addition, AFAICT each async COPY can copy an unlimited number of 4MB chunks, so can run for a long time. Thus IMO async COPY can become a DoS vector. Add a restriction mechanism that bounds the number of concurrent background COPY operations. Start simple and try to be fair -- this patch implements a per-namespace limit. An async COPY request that occurs while this limit is exceeded gets NFS4ERR_DELAY. The requesting client can choose to send the request again after a delay or fall back to a traditional read/write style copy. If there is need to make the mechanism more sophisticated, we can visit that in future patches.

In the Linux kernel, the following vulnerability has been resolved: l2tp: prevent possible tunnel refcount underflow When a session is created, it sets a backpointer to its tunnel. When the session refcount drops to 0, l2tp_session_free drops the tunnel refcount if session->tunnel is non-NULL. However, session->tunnel is set in l2tp_session_create, before the tunnel refcount is incremented by l2tp_session_register, which leaves a small window where session->tunnel is non-NULL when the tunnel refcount hasn't been bumped. Moving the assignment to l2tp_session_register is trivial but l2tp_session_create calls l2tp_session_set_header_len which uses session->tunnel to get the tunnel's encap. Add an encap arg to l2tp_session_set_header_len to avoid using session->tunnel. If l2tpv3 sessions have colliding IDs, it is possible for l2tp_v3_session_get to race with l2tp_session_register and fetch a session which doesn't yet have session->tunnel set. Add a check for this case.

In the Linux kernel, the following vulnerability has been resolved: regulator: rtq2208: Fix uninitialized use of regulator_config Fix rtq2208 driver uninitialized use to cause kernel error.

In the Linux kernel, the following vulnerability has been resolved: KVM: PPC: Fix kvm_arch_vcpu_ioctl vcpu_load leak vcpu_put is not called if the user copy fails. This can result in preempt notifier corruption and crashes, among other issues.

In the Linux kernel, the following vulnerability has been resolved: tcp: add sanity tests to TCP_QUEUE_SEQ Qingyu Li reported a syzkaller bug where the repro changes RCV SEQ _after_ restoring data in the receive queue. mprotect(0x4aa000, 12288, PROT_READ) = 0 mmap(0x1ffff000, 4096, PROT_NONE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x1ffff000 mmap(0x20000000, 16777216, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x20000000 mmap(0x21000000, 4096, PROT_NONE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x21000000 socket(AF_INET6, SOCK_STREAM, IPPROTO_IP) = 3 setsockopt(3, SOL_TCP, TCP_REPAIR, [1], 4) = 0 connect(3, {sa_family=AF_INET6, sin6_port=htons(0), sin6_flowinfo=htonl(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_scope_id=0}, 28) = 0 setsockopt(3, SOL_TCP, TCP_REPAIR_QUEUE, [1], 4) = 0 sendmsg(3, {msg_name=NULL, msg_namelen=0, msg_iov=[{iov_base="0x0000000000000003\0\0", iov_len=20}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 20 setsockopt(3, SOL_TCP, TCP_REPAIR, [0], 4) = 0 setsockopt(3, SOL_TCP, TCP_QUEUE_SEQ, [128], 4) = 0 recvfrom(3, NULL, 20, 0, NULL, NULL) = -1 ECONNRESET (Connection reset by peer) syslog shows: [ 111.205099] TCP recvmsg seq # bug 2: copied 80, seq 0, rcvnxt 80, fl 0 [ 111.207894] WARNING: CPU: 1 PID: 356 at net/ipv4/tcp.c:2343 tcp_recvmsg_locked+0x90e/0x29a0 This should not be allowed. TCP_QUEUE_SEQ should only be used when queues are empty. This patch fixes this case, and the tx path as well.

In the Linux kernel, the following vulnerability has been resolved: drm/tests: hdmi: Fix memory leaks in drm_display_mode_from_cea_vic() modprobe drm_hdmi_state_helper_test and then rmmod it, the following memory leak occurs. The `mode` allocated in drm_mode_duplicate() called by drm_display_mode_from_cea_vic() is not freed, which cause the memory leak: unreferenced object 0xffffff80ccd18100 (size 128): comm "kunit_try_catch", pid 1851, jiffies 4295059695 hex dump (first 32 bytes): 57 62 00 00 80 02 90 02 f0 02 20 03 00 00 e0 01 Wb........ ..... ea 01 ec 01 0d 02 00 00 0a 00 00 00 00 00 00 00 ................ backtrace (crc c2f1aa95): [<000000000f10b11b>] kmemleak_alloc+0x34/0x40 [<000000001cd4cf73>] __kmalloc_cache_noprof+0x26c/0x2f4 [<00000000f1f3cffa>] drm_mode_duplicate+0x44/0x19c [<000000008cbeef13>] drm_display_mode_from_cea_vic+0x88/0x98 [<0000000019daaacf>] 0xffffffedc11ae69c [<000000000aad0f85>] kunit_try_run_case+0x13c/0x3ac [<00000000a9210bac>] kunit_generic_run_threadfn_adapter+0x80/0xec [<000000000a0b2e9e>] kthread+0x2e8/0x374 [<00000000bd668858>] ret_from_fork+0x10/0x20 ...... Free `mode` by using drm_kunit_display_mode_from_cea_vic() to fix it.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/guc_submit: add missing locking in wedged_fini Any non-wedged queue can have a zero refcount here and can be running concurrently with an async queue destroy, therefore dereferencing the queue ptr to check wedge status after the lookup can trigger UAF if queue is not wedged. Fix this by keeping the submission_state lock held around the check to postpone the free and make the check safe, before dropping again around the put() to avoid the deadlock. (cherry picked from commit d28af0b6b9580b9f90c265a7da0315b0ad20bbfd)

In the Linux kernel, the following vulnerability has been resolved: net: Fix an unsafe loop on the list The kernel may crash when deleting a genetlink family if there are still listeners for that family: Oops: Kernel access of bad area, sig: 11 [#1] ... NIP [c000000000c080bc] netlink_update_socket_mc+0x3c/0xc0 LR [c000000000c0f764] __netlink_clear_multicast_users+0x74/0xc0 Call Trace: __netlink_clear_multicast_users+0x74/0xc0 genl_unregister_family+0xd4/0x2d0 Change the unsafe loop on the list to a safe one, because inside the loop there is an element removal from this list.

In the Linux kernel, the following vulnerability has been resolved: mlxsw: spectrum_ipip: Fix memory leak when changing remote IPv6 address The device stores IPv6 addresses that are used for encapsulation in linear memory that is managed by the driver. Changing the remote address of an ip6gre net device never worked properly, but since cited commit the following reproducer [1] would result in a warning [2] and a memory leak [3]. The problem is that the new remote address is never added by the driver to its hash table (and therefore the device) and the old address is never removed from it. Fix by programming the new address when the configuration of the ip6gre net device changes and removing the old one. If the address did not change, then the above would result in increasing the reference count of the address and then decreasing it. [1] # ip link add name bla up type ip6gre local 2001:db8:1::1 remote 2001:db8:2::1 tos inherit ttl inherit # ip link set dev bla type ip6gre remote 2001:db8:3::1 # ip link del dev bla # devlink dev reload pci/0000:01:00.0 [2] WARNING: CPU: 0 PID: 1682 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:3002 mlxsw_sp_ipv6_addr_put+0x140/0x1d0 Modules linked in: CPU: 0 UID: 0 PID: 1682 Comm: ip Not tainted 6.12.0-rc3-custom-g86b5b55bc835 #151 Hardware name: Nvidia SN5600/VMOD0013, BIOS 5.13 05/31/2023 RIP: 0010:mlxsw_sp_ipv6_addr_put+0x140/0x1d0 [...] Call Trace: <TASK> mlxsw_sp_router_netdevice_event+0x55f/0x1240 notifier_call_chain+0x5a/0xd0 call_netdevice_notifiers_info+0x39/0x90 unregister_netdevice_many_notify+0x63e/0x9d0 rtnl_dellink+0x16b/0x3a0 rtnetlink_rcv_msg+0x142/0x3f0 netlink_rcv_skb+0x50/0x100 netlink_unicast+0x242/0x390 netlink_sendmsg+0x1de/0x420 ____sys_sendmsg+0x2bd/0x320 ___sys_sendmsg+0x9a/0xe0 __sys_sendmsg+0x7a/0xd0 do_syscall_64+0x9e/0x1a0 entry_SYSCALL_64_after_hwframe+0x77/0x7f [3] unreferenced object 0xffff898081f597a0 (size 32): comm "ip", pid 1626, jiffies 4294719324 hex dump (first 32 bytes): 20 01 0d b8 00 02 00 00 00 00 00 00 00 00 00 01 ............... 21 49 61 83 80 89 ff ff 00 00 00 00 01 00 00 00 !Ia............. backtrace (crc fd9be911): [<00000000df89c55d>] __kmalloc_cache_noprof+0x1da/0x260 [<00000000ff2a1ddb>] mlxsw_sp_ipv6_addr_kvdl_index_get+0x281/0x340 [<000000009ddd445d>] mlxsw_sp_router_netdevice_event+0x47b/0x1240 [<00000000743e7757>] notifier_call_chain+0x5a/0xd0 [<000000007c7b9e13>] call_netdevice_notifiers_info+0x39/0x90 [<000000002509645d>] register_netdevice+0x5f7/0x7a0 [<00000000c2e7d2a9>] ip6gre_newlink_common.isra.0+0x65/0x130 [<0000000087cd6d8d>] ip6gre_newlink+0x72/0x120 [<000000004df7c7cc>] rtnl_newlink+0x471/0xa20 [<0000000057ed632a>] rtnetlink_rcv_msg+0x142/0x3f0 [<0000000032e0d5b5>] netlink_rcv_skb+0x50/0x100 [<00000000908bca63>] netlink_unicast+0x242/0x390 [<00000000cdbe1c87>] netlink_sendmsg+0x1de/0x420 [<0000000011db153e>] ____sys_sendmsg+0x2bd/0x320 [<000000003b6d53eb>] ___sys_sendmsg+0x9a/0xe0 [<00000000cae27c62>] __sys_sendmsg+0x7a/0xd0

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Validate hdwq pointers before dereferencing in reset/errata paths When the HBA is undergoing a reset or is handling an errata event, NULL ptr dereference crashes may occur in routines such as lpfc_sli_flush_io_rings(), lpfc_dev_loss_tmo_callbk(), or lpfc_abort_handler(). Add NULL ptr checks before dereferencing hdwq pointers that may have been freed due to operations colliding with a reset or errata event handler.

In the Linux kernel, the following vulnerability has been resolved: bpf: Check the remaining info_cnt before repeating btf fields When trying to repeat the btf fields for array of nested struct, it doesn't check the remaining info_cnt. The following splat will be reported when the value of ret * nelems is greater than BTF_FIELDS_MAX: ------------[ cut here ]------------ UBSAN: array-index-out-of-bounds in ../kernel/bpf/btf.c:3951:49 index 11 is out of range for type 'btf_field_info [11]' CPU: 6 UID: 0 PID: 411 Comm: test_progs ...... 6.11.0-rc4+ #1 Tainted: [O]=OOT_MODULE Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ... Call Trace: <TASK> dump_stack_lvl+0x57/0x70 dump_stack+0x10/0x20 ubsan_epilogue+0x9/0x40 __ubsan_handle_out_of_bounds+0x6f/0x80 ? kallsyms_lookup_name+0x48/0xb0 btf_parse_fields+0x992/0xce0 map_create+0x591/0x770 __sys_bpf+0x229/0x2410 __x64_sys_bpf+0x1f/0x30 x64_sys_call+0x199/0x9f0 do_syscall_64+0x3b/0xc0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x7fea56f2cc5d ...... </TASK> ---[ end trace ]--- Fix it by checking the remaining info_cnt in btf_repeat_fields() before repeating the btf fields.

In the Linux kernel, the following vulnerability has been resolved: cpufreq: amd-pstate: add check for cpufreq_cpu_get's return value cpufreq_cpu_get may return NULL. To avoid NULL-dereference check it and return in case of error. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: kthread: unpark only parked kthread Calling into kthread unparking unconditionally is mostly harmless when the kthread is already unparked. The wake up is then simply ignored because the target is not in TASK_PARKED state. However if the kthread is per CPU, the wake up is preceded by a call to kthread_bind() which expects the task to be inactive and in TASK_PARKED state, which obviously isn't the case if it is unparked. As a result, calling kthread_stop() on an unparked per-cpu kthread triggers such a warning: WARNING: CPU: 0 PID: 11 at kernel/kthread.c:525 __kthread_bind_mask kernel/kthread.c:525 <TASK> kthread_stop+0x17a/0x630 kernel/kthread.c:707 destroy_workqueue+0x136/0xc40 kernel/workqueue.c:5810 wg_destruct+0x1e2/0x2e0 drivers/net/wireguard/device.c:257 netdev_run_todo+0xe1a/0x1000 net/core/dev.c:10693 default_device_exit_batch+0xa14/0xa90 net/core/dev.c:11769 ops_exit_list net/core/net_namespace.c:178 [inline] cleanup_net+0x89d/0xcc0 net/core/net_namespace.c:640 process_one_work kernel/workqueue.c:3231 [inline] process_scheduled_works+0xa2c/0x1830 kernel/workqueue.c:3312 worker_thread+0x86d/0xd70 kernel/workqueue.c:3393 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 </TASK> Fix this with skipping unecessary unparking while stopping a kthread.

In the Linux kernel, the following vulnerability has been resolved: x86/mm/ident_map: Use gbpages only where full GB page should be mapped. When ident_pud_init() uses only GB pages to create identity maps, large ranges of addresses not actually requested can be included in the resulting table; a 4K request will map a full GB. This can include a lot of extra address space past that requested, including areas marked reserved by the BIOS. That allows processor speculation into reserved regions, that on UV systems can cause system halts. Only use GB pages when map creation requests include the full GB page of space. Fall back to using smaller 2M pages when only portions of a GB page are included in the request. No attempt is made to coalesce mapping requests. If a request requires a map entry at the 2M (pmd) level, subsequent mapping requests within the same 1G region will also be at the pmd level, even if adjacent or overlapping such requests could have been combined to map a full GB page. Existing usage starts with larger regions and then adds smaller regions, so this should not have any great consequence.

In the Linux kernel, the following vulnerability has been resolved: bpftool: Fix undefined behavior in qsort(NULL, 0, ...) When netfilter has no entry to display, qsort is called with qsort(NULL, 0, ...). This results in undefined behavior, as UBSan reports: net.c:827:2: runtime error: null pointer passed as argument 1, which is declared to never be null Although the C standard does not explicitly state whether calling qsort with a NULL pointer when the size is 0 constitutes undefined behavior, Section 7.1.4 of the C standard (Use of library functions) mentions: "Each of the following statements applies unless explicitly stated otherwise in the detailed descriptions that follow: If an argument to a function has an invalid value (such as a value outside the domain of the function, or a pointer outside the address space of the program, or a null pointer, or a pointer to non-modifiable storage when the corresponding parameter is not const-qualified) or a type (after promotion) not expected by a function with variable number of arguments, the behavior is undefined." To avoid this, add an early return when nf_link_info is NULL to prevent calling qsort with a NULL pointer.

In the Linux kernel, the following vulnerability has been resolved: ntfs3: Add bounds checking to mi_enum_attr() Added bounds checking to make sure that every attr don't stray beyond valid memory region.

In the Linux kernel, the following vulnerability has been resolved: jfs: check if leafidx greater than num leaves per dmap tree syzbot report a out of bounds in dbSplit, it because dmt_leafidx greater than num leaves per dmap tree, add a checking for dmt_leafidx in dbFindLeaf. Shaggy: Modified sanity check to apply to control pages as well as leaf pages.

In the Linux kernel, the following vulnerability has been resolved: drm/connector: hdmi: Fix memory leak in drm_display_mode_from_cea_vic() modprobe drm_connector_test and then rmmod drm_connector_test, the following memory leak occurs. The `mode` allocated in drm_mode_duplicate() called by drm_display_mode_from_cea_vic() is not freed, which cause the memory leak: unreferenced object 0xffffff80cb0ee400 (size 128): comm "kunit_try_catch", pid 1948, jiffies 4294950339 hex dump (first 32 bytes): 14 44 02 00 80 07 d8 07 04 08 98 08 00 00 38 04 .D............8. 3c 04 41 04 65 04 00 00 05 00 00 00 00 00 00 00 <.A.e........... backtrace (crc 90e9585c): [<00000000ec42e3d7>] kmemleak_alloc+0x34/0x40 [<00000000d0ef055a>] __kmalloc_cache_noprof+0x26c/0x2f4 [<00000000c2062161>] drm_mode_duplicate+0x44/0x19c [<00000000f96c74aa>] drm_display_mode_from_cea_vic+0x88/0x98 [<00000000d8f2c8b4>] 0xffffffdc982a4868 [<000000005d164dbc>] kunit_try_run_case+0x13c/0x3ac [<000000006fb23398>] kunit_generic_run_threadfn_adapter+0x80/0xec [<000000006ea56ca0>] kthread+0x2e8/0x374 [<000000000676063f>] ret_from_fork+0x10/0x20 ...... Free `mode` by using drm_kunit_display_mode_from_cea_vic() to fix it.

In the Linux kernel, the following vulnerability has been resolved: static_call: Handle module init failure correctly in static_call_del_module() Module insertion invokes static_call_add_module() to initialize the static calls in a module. static_call_add_module() invokes __static_call_init(), which allocates a struct static_call_mod to either encapsulate the built-in static call sites of the associated key into it so further modules can be added or to append the module to the module chain. If that allocation fails the function returns with an error code and the module core invokes static_call_del_module() to clean up eventually added static_call_mod entries. This works correctly, when all keys used by the module were converted over to a module chain before the failure. If not then static_call_del_module() causes a #GP as it blindly assumes that key::mods points to a valid struct static_call_mod. The problem is that key::mods is not a individual struct member of struct static_call_key, it's part of a union to save space: union { /* bit 0: 0 = mods, 1 = sites */ unsigned long type; struct static_call_mod *mods; struct static_call_site *sites; }; key::sites is a pointer to the list of built-in usage sites of the static call. The type of the pointer is differentiated by bit 0. A mods pointer has the bit clear, the sites pointer has the bit set. As static_call_del_module() blidly assumes that the pointer is a valid static_call_mod type, it fails to check for this failure case and dereferences the pointer to the list of built-in call sites, which is obviously bogus. Cure it by checking whether the key has a sites or a mods pointer. If it's a sites pointer then the key is not to be touched. As the sites are walked in the same order as in __static_call_init() the site walk can be terminated because all subsequent sites have not been touched by the init code due to the error exit. If it was converted before the allocation fail, then the inner loop which searches for a module match will find nothing. A fail in the second allocation in __static_call_init() is harmless and does not require special treatment. The first allocation succeeded and converted the key to a module chain. That first entry has mod::mod == NULL and mod::next == NULL, so the inner loop of static_call_del_module() will neither find a module match nor a module chain. The next site in the walk was either already converted, but can't match the module, or it will exit the outer loop because it has a static_call_site pointer and not a static_call_mod pointer.

In the Linux kernel, the following vulnerability has been resolved: platform/x86/intel/pmc: Fix pmc_core_iounmap to call iounmap for valid addresses Commit 50c6dbdfd16e ("x86/ioremap: Improve iounmap() address range checks") introduces a WARN when adrress ranges of iounmap are invalid. On Thinkpad P1 Gen 7 (Meteor Lake-P) this caused the following warning to appear: WARNING: CPU: 7 PID: 713 at arch/x86/mm/ioremap.c:461 iounmap+0x58/0x1f0 Modules linked in: rfkill(+) snd_timer(+) fjes(+) snd soundcore intel_pmc_core(+) int3403_thermal(+) int340x_thermal_zone intel_vsec pmt_telemetry acpi_pad pmt_class acpi_tad int3400_thermal acpi_thermal_rel joydev loop nfnetlink zram xe drm_suballoc_helper nouveau i915 mxm_wmi drm_ttm_helper gpu_sched drm_gpuvm drm_exec drm_buddy i2c_algo_bit crct10dif_pclmul crc32_pclmul ttm crc32c_intel polyval_clmulni rtsx_pci_sdmmc ucsi_acpi polyval_generic mmc_core hid_multitouch drm_display_helper ghash_clmulni_intel typec_ucsi nvme sha512_ssse3 video sha256_ssse3 nvme_core intel_vpu sha1_ssse3 rtsx_pci cec typec nvme_auth i2c_hid_acpi i2c_hid wmi pinctrl_meteorlake serio_raw ip6_tables ip_tables fuse CPU: 7 UID: 0 PID: 713 Comm: (udev-worker) Not tainted 6.12.0-rc2iounmap+ #42 Hardware name: LENOVO 21KWCTO1WW/21KWCTO1WW, BIOS N48ET19W (1.06 ) 07/18/2024 RIP: 0010:iounmap+0x58/0x1f0 Code: 85 6a 01 00 00 48 8b 05 e6 e2 28 04 48 39 c5 72 19 eb 26 cc cc cc 48 ba 00 00 00 00 00 00 32 00 48 8d 44 02 ff 48 39 c5 72 23 <0f> 0b 48 83 c4 08 5b 5d 41 5c c3 cc cc cc cc 48 ba 00 00 00 00 00 RSP: 0018:ffff888131eff038 EFLAGS: 00010207 RAX: ffffc90000000000 RBX: 0000000000000000 RCX: ffff888e33b80000 RDX: dffffc0000000000 RSI: ffff888e33bc29c0 RDI: 0000000000000000 RBP: 0000000000000000 R08: ffff8881598a8000 R09: ffff888e2ccedc10 R10: 0000000000000003 R11: ffffffffb3367634 R12: 00000000fe000000 R13: ffff888101d0da28 R14: ffffffffc2e437e0 R15: ffff888110b03b28 FS: 00007f3c1d4b3980(0000) GS:ffff888e33b80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005651cfc93578 CR3: 0000000124e4c002 CR4: 0000000000f70ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff07f0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> ? __warn.cold+0xb6/0x176 ? iounmap+0x58/0x1f0 ? report_bug+0x1f4/0x2b0 ? handle_bug+0x58/0x90 ? exc_invalid_op+0x17/0x40 ? asm_exc_invalid_op+0x1a/0x20 ? iounmap+0x58/0x1f0 pmc_core_ssram_get_pmc+0x477/0x6c0 [intel_pmc_core] ? __pfx_pmc_core_ssram_get_pmc+0x10/0x10 [intel_pmc_core] ? __pfx_do_pci_enable_device+0x10/0x10 ? pci_wait_for_pending+0x60/0x110 ? pci_enable_device_flags+0x1e3/0x2e0 ? __pfx_mtl_core_init+0x10/0x10 [intel_pmc_core] pmc_core_ssram_init+0x7f/0x110 [intel_pmc_core] mtl_core_init+0xda/0x130 [intel_pmc_core] ? __mutex_init+0xb9/0x130 pmc_core_probe+0x27e/0x10b0 [intel_pmc_core] ? _raw_spin_lock_irqsave+0x96/0xf0 ? __pfx_pmc_core_probe+0x10/0x10 [intel_pmc_core] ? __pfx_mutex_unlock+0x10/0x10 ? __pfx_mutex_lock+0x10/0x10 ? device_pm_check_callbacks+0x82/0x370 ? acpi_dev_pm_attach+0x234/0x2b0 platform_probe+0x9f/0x150 really_probe+0x1e0/0x8a0 __driver_probe_device+0x18c/0x370 ? __pfx___driver_attach+0x10/0x10 driver_probe_device+0x4a/0x120 __driver_attach+0x190/0x4a0 ? __pfx___driver_attach+0x10/0x10 bus_for_each_dev+0x103/0x180 ? __pfx_bus_for_each_dev+0x10/0x10 ? klist_add_tail+0x136/0x270 bus_add_driver+0x2fc/0x540 driver_register+0x1a5/0x360 ? __pfx_pmc_core_driver_init+0x10/0x10 [intel_pmc_core] do_one_initcall+0xa4/0x380 ? __pfx_do_one_initcall+0x10/0x10 ? kasan_unpoison+0x44/0x70 do_init_module+0x296/0x800 load_module+0x5090/0x6ce0 ? __pfx_load_module+0x10/0x10 ? ima_post_read_file+0x193/0x200 ? __pfx_ima_post_read_file+0x10/0x10 ? rw_verify_area+0x152/0x4c0 ? kernel_read_file+0x257/0x750 ? __pfx_kernel_read_file+0x10/0x10 ? __pfx_filemap_get_read_batch+0x10/0x10 ? init_module_from_file+0xd1/0x130 init_module_from_file+0xd1/0x130 ? __pfx_init_module_from_file+0x10/0 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: igb: Do not bring the device up after non-fatal error Commit 004d25060c78 ("igb: Fix igb_down hung on surprise removal") changed igb_io_error_detected() to ignore non-fatal pcie errors in order to avoid hung task that can happen when igb_down() is called multiple times. This caused an issue when processing transient non-fatal errors. igb_io_resume(), which is called after igb_io_error_detected(), assumes that device is brought down by igb_io_error_detected() if the interface is up. This resulted in panic with stacktrace below. [ T3256] igb 0000:09:00.0 haeth0: igb: haeth0 NIC Link is Down [ T292] pcieport 0000:00:1c.5: AER: Uncorrected (Non-Fatal) error received: 0000:09:00.0 [ T292] igb 0000:09:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID) [ T292] igb 0000:09:00.0: device [8086:1537] error status/mask=00004000/00000000 [ T292] igb 0000:09:00.0: [14] CmpltTO [ 200.105524,009][ T292] igb 0000:09:00.0: AER: TLP Header: 00000000 00000000 00000000 00000000 [ T292] pcieport 0000:00:1c.5: AER: broadcast error_detected message [ T292] igb 0000:09:00.0: Non-correctable non-fatal error reported. [ T292] pcieport 0000:00:1c.5: AER: broadcast mmio_enabled message [ T292] pcieport 0000:00:1c.5: AER: broadcast resume message [ T292] ------------[ cut here ]------------ [ T292] kernel BUG at net/core/dev.c:6539! [ T292] invalid opcode: 0000 [#1] PREEMPT SMP [ T292] RIP: 0010:napi_enable+0x37/0x40 [ T292] Call Trace: [ T292] <TASK> [ T292] ? die+0x33/0x90 [ T292] ? do_trap+0xdc/0x110 [ T292] ? napi_enable+0x37/0x40 [ T292] ? do_error_trap+0x70/0xb0 [ T292] ? napi_enable+0x37/0x40 [ T292] ? napi_enable+0x37/0x40 [ T292] ? exc_invalid_op+0x4e/0x70 [ T292] ? napi_enable+0x37/0x40 [ T292] ? asm_exc_invalid_op+0x16/0x20 [ T292] ? napi_enable+0x37/0x40 [ T292] igb_up+0x41/0x150 [ T292] igb_io_resume+0x25/0x70 [ T292] report_resume+0x54/0x70 [ T292] ? report_frozen_detected+0x20/0x20 [ T292] pci_walk_bus+0x6c/0x90 [ T292] ? aer_print_port_info+0xa0/0xa0 [ T292] pcie_do_recovery+0x22f/0x380 [ T292] aer_process_err_devices+0x110/0x160 [ T292] aer_isr+0x1c1/0x1e0 [ T292] ? disable_irq_nosync+0x10/0x10 [ T292] irq_thread_fn+0x1a/0x60 [ T292] irq_thread+0xe3/0x1a0 [ T292] ? irq_set_affinity_notifier+0x120/0x120 [ T292] ? irq_affinity_notify+0x100/0x100 [ T292] kthread+0xe2/0x110 [ T292] ? kthread_complete_and_exit+0x20/0x20 [ T292] ret_from_fork+0x2d/0x50 [ T292] ? kthread_complete_and_exit+0x20/0x20 [ T292] ret_from_fork_asm+0x11/0x20 [ T292] </TASK> To fix this issue igb_io_resume() checks if the interface is running and the device is not down this means igb_io_error_detected() did not bring the device down and there is no need to bring it up.

In the Linux kernel, the following vulnerability has been resolved: sfc: farch: fix TX queue lookup in TX flush done handling We're starting from a TXQ instance number ('qid'), not a TXQ type, so efx_get_tx_queue() is inappropriate (and could return NULL, leading to panics).