In the Linux kernel, the following vulnerability has been resolved: net: systemport: Add global locking for descriptor lifecycle The descriptor list is a shared resource across all of the transmit queues, and the locking mechanism used today only protects concurrency across a given transmit queue between the transmit and reclaiming. This creates an opportunity for the SYSTEMPORT hardware to work on corrupted descriptors if we have multiple producers at once which is the case when using multiple transmit queues. This was particularly noticeable when using multiple flows/transmit queues and it showed up in interesting ways in that UDP packets would get a correct UDP header checksum being calculated over an incorrect packet length. Similarly TCP packets would get an equally correct checksum computed by the hardware over an incorrect packet length. The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges when the driver produces a new descriptor anytime it writes to the WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to re-organize its descriptors and it is possible that concurrent TX queues eventually break this internal allocation scheme to the point where the length/status part of the descriptor gets used for an incorrect data buffer. The fix is to impose a global serialization for all TX queues in the short section where we are writing to the WRITE_PORT_{HI,LO} registers which solves the corruption even with multiple concurrent TX queues being used.

In the Linux kernel, the following vulnerability has been resolved: net: phy: dp83869: fix memory corruption when enabling fiber When configuring the fiber port, the DP83869 PHY driver incorrectly calls linkmode_set_bit() with a bit mask (1 << 10) rather than a bit number (10). This corrupts some other memory location -- in case of arm64 the priv pointer in the same structure. Since the advertising flags are updated from supported at the end of the function the incorrect line isn't needed at all and can be removed.

In the Linux kernel, the following vulnerability has been resolved: mptcp: pm: fix UaF read in mptcp_pm_nl_rm_addr_or_subflow Syzkaller reported this splat: ================================================================== BUG: KASAN: slab-use-after-free in mptcp_pm_nl_rm_addr_or_subflow+0xb44/0xcc0 net/mptcp/pm_netlink.c:881 Read of size 4 at addr ffff8880569ac858 by task syz.1.2799/14662 CPU: 0 UID: 0 PID: 14662 Comm: syz.1.2799 Not tainted 6.12.0-rc2-syzkaller-00307-g36c254515dc6 #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:377 [inline] print_report+0xc3/0x620 mm/kasan/report.c:488 kasan_report+0xd9/0x110 mm/kasan/report.c:601 mptcp_pm_nl_rm_addr_or_subflow+0xb44/0xcc0 net/mptcp/pm_netlink.c:881 mptcp_pm_nl_rm_subflow_received net/mptcp/pm_netlink.c:914 [inline] mptcp_nl_remove_id_zero_address+0x305/0x4a0 net/mptcp/pm_netlink.c:1572 mptcp_pm_nl_del_addr_doit+0x5c9/0x770 net/mptcp/pm_netlink.c:1603 genl_family_rcv_msg_doit+0x202/0x2f0 net/netlink/genetlink.c:1115 genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline] genl_rcv_msg+0x565/0x800 net/netlink/genetlink.c:1210 netlink_rcv_skb+0x165/0x410 net/netlink/af_netlink.c:2551 genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219 netlink_unicast_kernel net/netlink/af_netlink.c:1331 [inline] netlink_unicast+0x53c/0x7f0 net/netlink/af_netlink.c:1357 netlink_sendmsg+0x8b8/0xd70 net/netlink/af_netlink.c:1901 sock_sendmsg_nosec net/socket.c:729 [inline] __sock_sendmsg net/socket.c:744 [inline] ____sys_sendmsg+0x9ae/0xb40 net/socket.c:2607 ___sys_sendmsg+0x135/0x1e0 net/socket.c:2661 __sys_sendmsg+0x117/0x1f0 net/socket.c:2690 do_syscall_32_irqs_on arch/x86/entry/common.c:165 [inline] __do_fast_syscall_32+0x73/0x120 arch/x86/entry/common.c:386 do_fast_syscall_32+0x32/0x80 arch/x86/entry/common.c:411 entry_SYSENTER_compat_after_hwframe+0x84/0x8e RIP: 0023:0xf7fe4579 Code: b8 01 10 06 03 74 b4 01 10 07 03 74 b0 01 10 08 03 74 d8 01 00 00 00 00 00 00 00 00 00 00 00 00 00 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 8d b4 26 00 00 00 00 8d b4 26 00 00 00 00 RSP: 002b:00000000f574556c EFLAGS: 00000296 ORIG_RAX: 0000000000000172 RAX: ffffffffffffffda RBX: 000000000000000b RCX: 0000000020000140 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000296 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 </TASK> Allocated by task 5387: kasan_save_stack+0x33/0x60 mm/kasan/common.c:47 kasan_save_track+0x14/0x30 mm/kasan/common.c:68 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0xaa/0xb0 mm/kasan/common.c:394 kmalloc_noprof include/linux/slab.h:878 [inline] kzalloc_noprof include/linux/slab.h:1014 [inline] subflow_create_ctx+0x87/0x2a0 net/mptcp/subflow.c:1803 subflow_ulp_init+0xc3/0x4d0 net/mptcp/subflow.c:1956 __tcp_set_ulp net/ipv4/tcp_ulp.c:146 [inline] tcp_set_ulp+0x326/0x7f0 net/ipv4/tcp_ulp.c:167 mptcp_subflow_create_socket+0x4ae/0x10a0 net/mptcp/subflow.c:1764 __mptcp_subflow_connect+0x3cc/0x1490 net/mptcp/subflow.c:1592 mptcp_pm_create_subflow_or_signal_addr+0xbda/0x23a0 net/mptcp/pm_netlink.c:642 mptcp_pm_nl_fully_established net/mptcp/pm_netlink.c:650 [inline] mptcp_pm_nl_work+0x3a1/0x4f0 net/mptcp/pm_netlink.c:943 mptcp_worker+0x15a/0x1240 net/mptcp/protocol.c:2777 process_one_work+0x958/0x1b30 kernel/workqueue.c:3229 process_scheduled_works kernel/workqueue.c:3310 [inline] worker_thread+0x6c8/0xf00 kernel/workqueue.c:3391 kthread+0x2c1/0x3a0 kernel/kthread.c:389 ret_from_fork+0x45/0x80 arch/x86/ke ---truncated---

In the Linux kernel, the following vulnerability has been resolved: iio: gts-helper: Fix memory leaks in iio_gts_build_avail_scale_table() modprobe iio-test-gts and rmmod it, then the following memory leak occurs: unreferenced object 0xffffff80c810be00 (size 64): comm "kunit_try_catch", pid 1654, jiffies 4294913981 hex dump (first 32 bytes): 02 00 00 00 08 00 00 00 20 00 00 00 40 00 00 00 ........ ...@... 80 00 00 00 00 02 00 00 00 04 00 00 00 08 00 00 ................ backtrace (crc a63d875e): [<0000000028c1b3c2>] kmemleak_alloc+0x34/0x40 [<000000001d6ecc87>] __kmalloc_noprof+0x2bc/0x3c0 [<00000000393795c1>] devm_iio_init_iio_gts+0x4b4/0x16f4 [<0000000071bb4b09>] 0xffffffdf052a62e0 [<000000000315bc18>] 0xffffffdf052a6488 [<00000000f9dc55b5>] kunit_try_run_case+0x13c/0x3ac [<00000000175a3fd4>] kunit_generic_run_threadfn_adapter+0x80/0xec [<00000000f505065d>] kthread+0x2e8/0x374 [<00000000bbfb0e5d>] ret_from_fork+0x10/0x20 unreferenced object 0xffffff80cbfe9e70 (size 16): comm "kunit_try_catch", pid 1658, jiffies 4294914015 hex dump (first 16 bytes): 10 00 00 00 40 00 00 00 80 00 00 00 00 00 00 00 ....@........... backtrace (crc 857f0cb4): [<0000000028c1b3c2>] kmemleak_alloc+0x34/0x40 [<000000001d6ecc87>] __kmalloc_noprof+0x2bc/0x3c0 [<00000000393795c1>] devm_iio_init_iio_gts+0x4b4/0x16f4 [<0000000071bb4b09>] 0xffffffdf052a62e0 [<000000007d089d45>] 0xffffffdf052a6864 [<00000000f9dc55b5>] kunit_try_run_case+0x13c/0x3ac [<00000000175a3fd4>] kunit_generic_run_threadfn_adapter+0x80/0xec [<00000000f505065d>] kthread+0x2e8/0x374 [<00000000bbfb0e5d>] ret_from_fork+0x10/0x20 ...... It includes 5*5 times "size 64" memory leaks, which correspond to 5 times test_init_iio_gain_scale() calls with gts_test_gains size 10 (10*size(int)) and gts_test_itimes size 5. It also includes 5*1 times "size 16" memory leak, which correspond to one time __test_init_iio_gain_scale() call with gts_test_gains_gain_low size 3 (3*size(int)) and gts_test_itimes size 5. The reason is that the per_time_gains[i] is not freed which is allocated in the "gts->num_itime" for loop in iio_gts_build_avail_scale_table().

In the Linux kernel, the following vulnerability has been resolved: mac80211: validate extended element ID is present Before attempting to parse an extended element, verify that the extended element ID is present.

In the Linux kernel, the following vulnerability has been resolved: blk-mq: cancel blk-mq dispatch work in both blk_cleanup_queue and disk_release() For avoiding to slow down queue destroy, we don't call blk_mq_quiesce_queue() in blk_cleanup_queue(), instead of delaying to cancel dispatch work in blk_release_queue(). However, this way has caused kernel oops[1], reported by Changhui. The log shows that scsi_device can be freed before running blk_release_queue(), which is expected too since scsi_device is released after the scsi disk is closed and the scsi_device is removed. Fixes the issue by canceling blk-mq dispatch work in both blk_cleanup_queue() and disk_release(): 1) when disk_release() is run, the disk has been closed, and any sync dispatch activities have been done, so canceling dispatch work is enough to quiesce filesystem I/O dispatch activity. 2) in blk_cleanup_queue(), we only focus on passthrough request, and passthrough request is always explicitly allocated & freed by its caller, so once queue is frozen, all sync dispatch activity for passthrough request has been done, then it is enough to just cancel dispatch work for avoiding any dispatch activity. [1] kernel panic log [12622.769416] BUG: kernel NULL pointer dereference, address: 0000000000000300 [12622.777186] #PF: supervisor read access in kernel mode [12622.782918] #PF: error_code(0x0000) - not-present page [12622.788649] PGD 0 P4D 0 [12622.791474] Oops: 0000 [#1] PREEMPT SMP PTI [12622.796138] CPU: 10 PID: 744 Comm: kworker/10:1H Kdump: loaded Not tainted 5.15.0+ #1 [12622.804877] Hardware name: Dell Inc. PowerEdge R730/0H21J3, BIOS 1.5.4 10/002/2015 [12622.813321] Workqueue: kblockd blk_mq_run_work_fn [12622.818572] RIP: 0010:sbitmap_get+0x75/0x190 [12622.823336] Code: 85 80 00 00 00 41 8b 57 08 85 d2 0f 84 b1 00 00 00 45 31 e4 48 63 cd 48 8d 1c 49 48 c1 e3 06 49 03 5f 10 4c 8d 6b 40 83 f0 01 <48> 8b 33 44 89 f2 4c 89 ef 0f b6 c8 e8 fa f3 ff ff 83 f8 ff 75 58 [12622.844290] RSP: 0018:ffffb00a446dbd40 EFLAGS: 00010202 [12622.850120] RAX: 0000000000000001 RBX: 0000000000000300 RCX: 0000000000000004 [12622.858082] RDX: 0000000000000006 RSI: 0000000000000082 RDI: ffffa0b7a2dfe030 [12622.866042] RBP: 0000000000000004 R08: 0000000000000001 R09: ffffa0b742721334 [12622.874003] R10: 0000000000000008 R11: 0000000000000008 R12: 0000000000000000 [12622.881964] R13: 0000000000000340 R14: 0000000000000000 R15: ffffa0b7a2dfe030 [12622.889926] FS: 0000000000000000(0000) GS:ffffa0baafb40000(0000) knlGS:0000000000000000 [12622.898956] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [12622.905367] CR2: 0000000000000300 CR3: 0000000641210001 CR4: 00000000001706e0 [12622.913328] Call Trace: [12622.916055] <TASK> [12622.918394] scsi_mq_get_budget+0x1a/0x110 [12622.922969] __blk_mq_do_dispatch_sched+0x1d4/0x320 [12622.928404] ? pick_next_task_fair+0x39/0x390 [12622.933268] __blk_mq_sched_dispatch_requests+0xf4/0x140 [12622.939194] blk_mq_sched_dispatch_requests+0x30/0x60 [12622.944829] __blk_mq_run_hw_queue+0x30/0xa0 [12622.949593] process_one_work+0x1e8/0x3c0 [12622.954059] worker_thread+0x50/0x3b0 [12622.958144] ? rescuer_thread+0x370/0x370 [12622.962616] kthread+0x158/0x180 [12622.966218] ? set_kthread_struct+0x40/0x40 [12622.970884] ret_from_fork+0x22/0x30 [12622.974875] </TASK> [12622.977309] Modules linked in: scsi_debug rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs sunrpc dm_multipath intel_rapl_msr intel_rapl_common dell_wmi_descriptor sb_edac rfkill video x86_pkg_temp_thermal intel_powerclamp dcdbas coretemp kvm_intel kvm mgag200 irqbypass i2c_algo_bit rapl drm_kms_helper ipmi_ssif intel_cstate intel_uncore syscopyarea sysfillrect sysimgblt fb_sys_fops pcspkr cec mei_me lpc_ich mei ipmi_si ipmi_devintf ipmi_msghandler acpi_power_meter drm fuse xfs libcrc32c sr_mod cdrom sd_mod t10_pi sg ixgbe ahci libahci crct10dif_pclmul crc32_pclmul crc32c_intel libata megaraid_sas ghash_clmulni_intel tg3 wdat_w ---truncated---

In the Linux kernel, the following vulnerability has been resolved: remoteproc: k3-r5: Fix error handling when power-up failed By simply bailing out, the driver was violating its rule and internal assumptions that either both or no rproc should be initialized. E.g., this could cause the first core to be available but not the second one, leading to crashes on its shutdown later on while trying to dereference that second instance.

In the Linux kernel, the following vulnerability has been resolved: pmdomain: imx93-blk-ctrl: correct remove path The check condition should be 'i < bc->onecell_data.num_domains', not 'bc->onecell_data.num_domains' which will make the look never finish and cause kernel panic. Also disable runtime to address "imx93-blk-ctrl 4ac10000.system-controller: Unbalanced pm_runtime_enable!"

An issue was discovered in the Linux kernel before 5.8. lib/nlattr.c allows attackers to cause a denial of service (unbounded recursion) via a nested Netlink policy with a back reference.

In the Linux kernel, the following vulnerability has been resolved: stackdepot: fix stack_depot_save_flags() in NMI context Per documentation, stack_depot_save_flags() was meant to be usable from NMI context if STACK_DEPOT_FLAG_CAN_ALLOC is unset. However, it still would try to take the pool_lock in an attempt to save a stack trace in the current pool (if space is available). This could result in deadlock if an NMI is handled while pool_lock is already held. To avoid deadlock, only try to take the lock in NMI context and give up if unsuccessful. The documentation is fixed to clearly convey this.

In the Linux kernel, the following vulnerability has been resolved: sched/core: Disable page allocation in task_tick_mm_cid() With KASAN and PREEMPT_RT enabled, calling task_work_add() in task_tick_mm_cid() may cause the following splat. [ 63.696416] BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 [ 63.696416] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 610, name: modprobe [ 63.696416] preempt_count: 10001, expected: 0 [ 63.696416] RCU nest depth: 1, expected: 1 This problem is caused by the following call trace. sched_tick() [ acquire rq->__lock ] -> task_tick_mm_cid() -> task_work_add() -> __kasan_record_aux_stack() -> kasan_save_stack() -> stack_depot_save_flags() -> alloc_pages_mpol_noprof() -> __alloc_pages_noprof() -> get_page_from_freelist() -> rmqueue() -> rmqueue_pcplist() -> __rmqueue_pcplist() -> rmqueue_bulk() -> rt_spin_lock() The rq lock is a raw_spinlock_t. We can't sleep while holding it. IOW, we can't call alloc_pages() in stack_depot_save_flags(). The task_tick_mm_cid() function with its task_work_add() call was introduced by commit 223baf9d17f2 ("sched: Fix performance regression introduced by mm_cid") in v6.4 kernel. Fortunately, there is a kasan_record_aux_stack_noalloc() variant that calls stack_depot_save_flags() while not allowing it to allocate new pages. To allow task_tick_mm_cid() to use task_work without page allocation, a new TWAF_NO_ALLOC flag is added to enable calling kasan_record_aux_stack_noalloc() instead of kasan_record_aux_stack() if set. The task_tick_mm_cid() function is modified to add this new flag. The possible downside is the missing stack trace in a KASAN report due to new page allocation required when task_work_add_noallloc() is called which should be rare.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: check outstanding simultaneous SMB operations If Client send simultaneous SMB operations to ksmbd, It exhausts too much memory through the "ksmbd_work_cache”. It will cause OOM issue. ksmbd has a credit mechanism but it can't handle this problem. This patch add the check if it exceeds max credits to prevent this problem by assuming that one smb request consumes at least one credit.

In the Linux kernel, the following vulnerability has been resolved: media: dvbdev: Fix memory leak in dvb_media_device_free() dvb_media_device_free() is leaking memory. Free `dvbdev->adapter->conn` before setting it to NULL, as documented in include/media/media-device.h: "The media_entity instance itself must be freed explicitly by the driver if required."

In the Linux kernel, the following vulnerability has been resolved: netfs: Delete subtree of 'fs/netfs' when netfs module exits In netfs_init() or fscache_proc_init(), we create dentry under 'fs/netfs', but in netfs_exit(), we only delete the proc entry of 'fs/netfs' without deleting its subtree. This triggers the following WARNING: ================================================================== remove_proc_entry: removing non-empty directory 'fs/netfs', leaking at least 'requests' WARNING: CPU: 4 PID: 566 at fs/proc/generic.c:717 remove_proc_entry+0x160/0x1c0 Modules linked in: netfs(-) CPU: 4 UID: 0 PID: 566 Comm: rmmod Not tainted 6.11.0-rc3 #860 RIP: 0010:remove_proc_entry+0x160/0x1c0 Call Trace: <TASK> netfs_exit+0x12/0x620 [netfs] __do_sys_delete_module.isra.0+0x14c/0x2e0 do_syscall_64+0x4b/0x110 entry_SYSCALL_64_after_hwframe+0x76/0x7e ================================================================== Therefore use remove_proc_subtree() instead of remove_proc_entry() to fix the above problem.

In the Linux kernel, the following vulnerability has been resolved: vdpa_sim: avoid putting an uninitialized iova_domain The system will crash if we put an uninitialized iova_domain, this could happen when an error occurs before initializing the iova_domain in vdpasim_create(). BUG: kernel NULL pointer dereference, address: 0000000000000000 ... RIP: 0010:__cpuhp_state_remove_instance+0x96/0x1c0 ... Call Trace: <TASK> put_iova_domain+0x29/0x220 vdpasim_free+0xd1/0x120 [vdpa_sim] vdpa_release_dev+0x21/0x40 [vdpa] device_release+0x33/0x90 kobject_release+0x63/0x160 vdpasim_create+0x127/0x2a0 [vdpa_sim] vdpasim_net_dev_add+0x7d/0xfe [vdpa_sim_net] vdpa_nl_cmd_dev_add_set_doit+0xe1/0x1a0 [vdpa] genl_family_rcv_msg_doit+0x112/0x140 genl_rcv_msg+0xdf/0x1d0 ... So we must make sure the iova_domain is already initialized before put it. In addition, we may get the following warning in this case: WARNING: ... drivers/iommu/iova.c:344 iova_cache_put+0x58/0x70 So we must make sure the iova_cache_put() is invoked only if the iova_cache_get() is already invoked. Let's fix it together.

In the Linux kernel, the following vulnerability has been resolved: fs: don't try and remove empty rbtree node When copying a namespace we won't have added the new copy into the namespace rbtree until after the copy succeeded. Calling free_mnt_ns() will try to remove the copy from the rbtree which is invalid. Simply free the namespace skeleton directly.

An issue was discovered in the Linux kernel before 5.8.10. virt/kvm/kvm_main.c has a kvm_io_bus_unregister_dev memory leak upon a kmalloc failure, aka CID-f65886606c2d.

In the Linux kernel, the following vulnerability has been resolved: media: cx24116: prevent overflows on SNR calculus as reported by Coverity, if reading SNR registers fail, a negative number will be returned, causing an underflow when reading SNR registers. Prevent that.

In the Linux kernel, the following vulnerability has been resolved: fuse: use exclusive lock when FUSE_I_CACHE_IO_MODE is set This may be a typo. The comment has said shared locks are not allowed when this bit is set. If using shared lock, the wait in `fuse_file_cached_io_open` may be forever.

In the Linux kernel, the following vulnerability has been resolved: scsi: target: core: Fix null-ptr-deref in target_alloc_device() There is a null-ptr-deref issue reported by KASAN: BUG: KASAN: null-ptr-deref in target_alloc_device+0xbc4/0xbe0 [target_core_mod] ... kasan_report+0xb9/0xf0 target_alloc_device+0xbc4/0xbe0 [target_core_mod] core_dev_setup_virtual_lun0+0xef/0x1f0 [target_core_mod] target_core_init_configfs+0x205/0x420 [target_core_mod] do_one_initcall+0xdd/0x4e0 ... entry_SYSCALL_64_after_hwframe+0x76/0x7e In target_alloc_device(), if allocing memory for dev queues fails, then dev will be freed by dev->transport->free_device(), but dev->transport is not initialized at that time, which will lead to a null pointer reference problem. Fixing this bug by freeing dev with hba->backend->ops->free_device().

In the Linux kernel, the following vulnerability has been resolved: ALSA: firewire-lib: Avoid division by zero in apply_constraint_to_size() The step variable is initialized to zero. It is changed in the loop, but if it's not changed it will remain zero. Add a variable check before the division. The observed behavior was introduced by commit 826b5de90c0b ("ALSA: firewire-lib: fix insufficient PCM rule for period/buffer size"), and it is difficult to show that any of the interval parameters will satisfy the snd_interval_test() condition with data from the amdtp_rate_table[] table. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid potential deadlock Using f2fs_trylock_op() in f2fs_write_compressed_pages() to avoid potential deadlock like we did in f2fs_write_single_data_page().

In the Linux kernel, the following vulnerability has been resolved: i2c: imx: fix reference leak when pm_runtime_get_sync fails In i2c_imx_xfer() and i2c_imx_remove(), the pm reference count is not expected to be incremented on return. However, pm_runtime_get_sync will increment pm reference count even failed. Forgetting to putting operation will result in a reference leak here. Replace it with pm_runtime_resume_and_get to keep usage counter balanced.

In the Linux kernel, the following vulnerability has been resolved: virtio_pmem: Check device status before requesting flush If a pmem device is in a bad status, the driver side could wait for host ack forever in virtio_pmem_flush(), causing the system to hang. So add a status check in the beginning of virtio_pmem_flush() to return early if the device is not activated.

In the Linux kernel, the following vulnerability has been resolved: net: qlogic: qlcnic: Fix a NULL pointer dereference in qlcnic_83xx_add_rings() In qlcnic_83xx_add_rings(), the indirect function of ahw->hw_ops->alloc_mbx_args will be called to allocate memory for cmd.req.arg, and there is a dereference of it in qlcnic_83xx_add_rings(), which could lead to a NULL pointer dereference on failure of the indirect function like qlcnic_83xx_alloc_mbx_args(). Fix this bug by adding a check of alloc_mbx_args(), this patch imitates the logic of mbx_cmd()'s failure handling. This bug was found by a static analyzer. The analysis employs differential checking to identify inconsistent security operations (e.g., checks or kfrees) between two code paths and confirms that the inconsistent operations are not recovered in the current function or the callers, so they constitute bugs. Note that, as a bug found by static analysis, it can be a false positive or hard to trigger. Multiple researchers have cross-reviewed the bug. Builds with CONFIG_QLCNIC=m show no new warnings, and our static analyzer no longer warns about this code.

In the Linux kernel, the following vulnerability has been resolved: mptcp: clear 'kern' flag from fallback sockets The mptcp ULP extension relies on sk->sk_sock_kern being set correctly: It prevents setsockopt(fd, IPPROTO_TCP, TCP_ULP, "mptcp", 6); from working for plain tcp sockets (any userspace-exposed socket). But in case of fallback, accept() can return a plain tcp sk. In such case, sk is still tagged as 'kernel' and setsockopt will work. This will crash the kernel, The subflow extension has a NULL ctx->conn mptcp socket: BUG: KASAN: null-ptr-deref in subflow_data_ready+0x181/0x2b0 Call Trace: tcp_data_ready+0xf8/0x370 [..]

In the Linux kernel, the following vulnerability has been resolved: ixgbe: Fix NULL pointer dereference in ixgbe_xdp_setup The ixgbe driver currently generates a NULL pointer dereference with some machine (online cpus < 63). This is due to the fact that the maximum value of num_xdp_queues is nr_cpu_ids. Code is in "ixgbe_set_rss_queues"". Here's how the problem repeats itself: Some machine (online cpus < 63), And user set num_queues to 63 through ethtool. Code is in the "ixgbe_set_channels", adapter->ring_feature[RING_F_FDIR].limit = count; It becomes 63. When user use xdp, "ixgbe_set_rss_queues" will set queues num. adapter->num_rx_queues = rss_i; adapter->num_tx_queues = rss_i; adapter->num_xdp_queues = ixgbe_xdp_queues(adapter); And rss_i's value is from f = &adapter->ring_feature[RING_F_FDIR]; rss_i = f->indices = f->limit; So "num_rx_queues" > "num_xdp_queues", when run to "ixgbe_xdp_setup", for (i = 0; i < adapter->num_rx_queues; i++) if (adapter->xdp_ring[i]->xsk_umem) It leads to panic. Call trace: [exception RIP: ixgbe_xdp+368] RIP: ffffffffc02a76a0 RSP: ffff9fe16202f8d0 RFLAGS: 00010297 RAX: 0000000000000000 RBX: 0000000000000020 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 000000000000001c RDI: ffffffffa94ead90 RBP: ffff92f8f24c0c18 R8: 0000000000000000 R9: 0000000000000000 R10: ffff9fe16202f830 R11: 0000000000000000 R12: ffff92f8f24c0000 R13: ffff9fe16202fc01 R14: 000000000000000a R15: ffffffffc02a7530 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 7 [ffff9fe16202f8f0] dev_xdp_install at ffffffffa89fbbcc 8 [ffff9fe16202f920] dev_change_xdp_fd at ffffffffa8a08808 9 [ffff9fe16202f960] do_setlink at ffffffffa8a20235 10 [ffff9fe16202fa88] rtnl_setlink at ffffffffa8a20384 11 [ffff9fe16202fc78] rtnetlink_rcv_msg at ffffffffa8a1a8dd 12 [ffff9fe16202fcf0] netlink_rcv_skb at ffffffffa8a717eb 13 [ffff9fe16202fd40] netlink_unicast at ffffffffa8a70f88 14 [ffff9fe16202fd80] netlink_sendmsg at ffffffffa8a71319 15 [ffff9fe16202fdf0] sock_sendmsg at ffffffffa89df290 16 [ffff9fe16202fe08] __sys_sendto at ffffffffa89e19c8 17 [ffff9fe16202ff30] __x64_sys_sendto at ffffffffa89e1a64 18 [ffff9fe16202ff38] do_syscall_64 at ffffffffa84042b9 19 [ffff9fe16202ff50] entry_SYSCALL_64_after_hwframe at ffffffffa8c0008c So I fix ixgbe_max_channels so that it will not allow a setting of queues to be higher than the num_online_cpus(). And when run to ixgbe_xdp_setup, take the smaller value of num_rx_queues and num_xdp_queues.

In the Linux kernel, the following vulnerability has been resolved: drm/virtio: Ensure that objs is not NULL in virtio_gpu_array_put_free() If virtio_gpu_object_shmem_init() fails (e.g. due to fault injection, as it happened in the bug report by syzbot), virtio_gpu_array_put_free() could be called with objs equal to NULL. Ensure that objs is not NULL in virtio_gpu_array_put_free(), or otherwise return from the function.

In the Linux kernel, the following vulnerability has been resolved: gpu: host1x: Fix a memory leak in 'host1x_remove()' Add a missing 'host1x_channel_list_free()' call in the remove function, as already done in the error handling path of the probe function.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix null-ptr-deref in block_touch_buffer tracepoint Patch series "nilfs2: fix null-ptr-deref bugs on block tracepoints". This series fixes null pointer dereference bugs that occur when using nilfs2 and two block-related tracepoints. This patch (of 2): It has been reported that when using "block:block_touch_buffer" tracepoint, touch_buffer() called from __nilfs_get_folio_block() causes a NULL pointer dereference, or a general protection fault when KASAN is enabled. This happens because since the tracepoint was added in touch_buffer(), it references the dev_t member bh->b_bdev->bd_dev regardless of whether the buffer head has a pointer to a block_device structure. In the current implementation, the block_device structure is set after the function returns to the caller. Here, touch_buffer() is used to mark the folio/page that owns the buffer head as accessed, but the common search helper for folio/page used by the caller function was optimized to mark the folio/page as accessed when it was reimplemented a long time ago, eliminating the need to call touch_buffer() here in the first place. So this solves the issue by eliminating the touch_buffer() call itself.

In the Linux kernel, the following vulnerability has been resolved: i2c: xiic: fix reference leak when pm_runtime_get_sync fails The PM reference count is not expected to be incremented on return in xiic_xfer and xiic_i2c_remove. However, pm_runtime_get_sync will increment the PM reference count even failed. Forgetting to putting operation will result in a reference leak here. Replace it with pm_runtime_resume_and_get to keep usage counter balanced.

In the Linux kernel, the following vulnerability has been resolved: PCI: qcom-ep: Move controller cleanups to qcom_pcie_perst_deassert() Currently, the endpoint cleanup function dw_pcie_ep_cleanup() and EPF deinit notify function pci_epc_deinit_notify() are called during the execution of qcom_pcie_perst_assert() i.e., when the host has asserted PERST#. But quickly after this step, refclk will also be disabled by the host. All of the Qcom endpoint SoCs supported as of now depend on the refclk from the host for keeping the controller operational. Due to this limitation, any access to the hardware registers in the absence of refclk will result in a whole endpoint crash. Unfortunately, most of the controller cleanups require accessing the hardware registers (like eDMA cleanup performed in dw_pcie_ep_cleanup(), powering down MHI EPF etc...). So these cleanup functions are currently causing the crash in the endpoint SoC once host asserts PERST#. One way to address this issue is by generating the refclk in the endpoint itself and not depending on the host. But that is not always possible as some of the endpoint designs do require the endpoint to consume refclk from the host (as I was told by the Qcom engineers). Thus, fix this crash by moving the controller cleanups to the start of the qcom_pcie_perst_deassert() function. qcom_pcie_perst_deassert() is called whenever the host has deasserted PERST# and it is guaranteed that the refclk would be active at this point. So at the start of this function (after enabling resources), the controller cleanup can be performed. Once finished, rest of the code execution for PERST# deassert can continue as usual.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix possible double free in smb2_set_ea() Clang static checker(scan-build) warning： fs/smb/client/smb2ops.c:1304:2: Attempt to free released memory. 1304 | kfree(ea); | ^~~~~~~~~ There is a double free in such case: 'ea is initialized to NULL' -> 'first successful memory allocation for ea' -> 'something failed, goto sea_exit' -> 'first memory release for ea' -> 'goto replay_again' -> 'second goto sea_exit before allocate memory for ea' -> 'second memory release for ea resulted in double free'. Re-initialie 'ea' to NULL near to the replay_again label, it can fix this double free problem.

In the Linux kernel, the following vulnerability has been resolved: arm64: probes: Remove broken LDR (literal) uprobe support The simulate_ldr_literal() and simulate_ldrsw_literal() functions are unsafe to use for uprobes. Both functions were originally written for use with kprobes, and access memory with plain C accesses. When uprobes was added, these were reused unmodified even though they cannot safely access user memory. There are three key problems: 1) The plain C accesses do not have corresponding extable entries, and thus if they encounter a fault the kernel will treat these as unintentional accesses to user memory, resulting in a BUG() which will kill the kernel thread, and likely lead to further issues (e.g. lockup or panic()). 2) The plain C accesses are subject to HW PAN and SW PAN, and so when either is in use, any attempt to simulate an access to user memory will fault. Thus neither simulate_ldr_literal() nor simulate_ldrsw_literal() can do anything useful when simulating a user instruction on any system with HW PAN or SW PAN. 3) The plain C accesses are privileged, as they run in kernel context, and in practice can access a small range of kernel virtual addresses. The instructions they simulate have a range of +/-1MiB, and since the simulated instructions must itself be a user instructions in the TTBR0 address range, these can address the final 1MiB of the TTBR1 acddress range by wrapping downwards from an address in the first 1MiB of the TTBR0 address range. In contemporary kernels the last 8MiB of TTBR1 address range is reserved, and accesses to this will always fault, meaning this is no worse than (1). Historically, it was theoretically possible for the linear map or vmemmap to spill into the final 8MiB of the TTBR1 address range, but in practice this is extremely unlikely to occur as this would require either: * Having enough physical memory to fill the entire linear map all the way to the final 1MiB of the TTBR1 address range. * Getting unlucky with KASLR randomization of the linear map such that the populated region happens to overlap with the last 1MiB of the TTBR address range. ... and in either case if we were to spill into the final page there would be larger problems as the final page would alias with error pointers. Practically speaking, (1) and (2) are the big issues. Given there have been no reports of problems since the broken code was introduced, it appears that no-one is relying on probing these instructions with uprobes. Avoid these issues by not allowing uprobes on LDR (literal) and LDRSW (literal), limiting the use of simulate_ldr_literal() and simulate_ldrsw_literal() to kprobes. Attempts to place uprobes on LDR (literal) and LDRSW (literal) will be rejected as arm_probe_decode_insn() will return INSN_REJECTED. In future we can consider introducing working uprobes support for these instructions, but this will require more significant work.

In the Linux kernel, the following vulnerability has been resolved: ipv6: fix memory leak in fib6_rule_suppress The kernel leaks memory when a `fib` rule is present in IPv6 nftables firewall rules and a suppress_prefix rule is present in the IPv6 routing rules (used by certain tools such as wg-quick). In such scenarios, every incoming packet will leak an allocation in `ip6_dst_cache` slab cache. After some hours of `bpftrace`-ing and source code reading, I tracked down the issue to ca7a03c41753 ("ipv6: do not free rt if FIB_LOOKUP_NOREF is set on suppress rule"). The problem with that change is that the generic `args->flags` always have `FIB_LOOKUP_NOREF` set[1][2] but the IPv6-specific flag `RT6_LOOKUP_F_DST_NOREF` might not be, leading to `fib6_rule_suppress` not decreasing the refcount when needed. How to reproduce: - Add the following nftables rule to a prerouting chain: meta nfproto ipv6 fib saddr . mark . iif oif missing drop This can be done with: sudo nft create table inet test sudo nft create chain inet test test_chain '{ type filter hook prerouting priority filter + 10; policy accept; }' sudo nft add rule inet test test_chain meta nfproto ipv6 fib saddr . mark . iif oif missing drop - Run: sudo ip -6 rule add table main suppress_prefixlength 0 - Watch `sudo slabtop -o | grep ip6_dst_cache` to see memory usage increase with every incoming ipv6 packet. This patch exposes the protocol-specific flags to the protocol specific `suppress` function, and check the protocol-specific `flags` argument for RT6_LOOKUP_F_DST_NOREF instead of the generic FIB_LOOKUP_NOREF when decreasing the refcount, like this. [1]: https://github.com/torvalds/linux/blob/ca7a03c4175366a92cee0ccc4fec0038c3266e26/net/ipv6/fib6_rules.c#L71 [2]: https://github.com/torvalds/linux/blob/ca7a03c4175366a92cee0ccc4fec0038c3266e26/net/ipv6/fib6_rules.c#L99

In the Linux kernel, the following vulnerability has been resolved: mac80211: track only QoS data frames for admission control For admission control, obviously all of that only works for QoS data frames, otherwise we cannot even access the QoS field in the header. Syzbot reported (see below) an uninitialized value here due to a status of a non-QoS nullfunc packet, which isn't even long enough to contain the QoS header. Fix this to only do anything for QoS data packets.

In the Linux kernel, the following vulnerability has been resolved: mm: turn folio_test_hugetlb into a PageType The current folio_test_hugetlb() can be fooled by a concurrent folio split into returning true for a folio which has never belonged to hugetlbfs. This can't happen if the caller holds a refcount on it, but we have a few places (memory-failure, compaction, procfs) which do not and should not take a speculative reference. Since hugetlb pages do not use individual page mapcounts (they are always fully mapped and use the entire_mapcount field to record the number of mappings), the PageType field is available now that page_mapcount() ignores the value in this field. In compaction and with CONFIG_DEBUG_VM enabled, the current implementation can result in an oops, as reported by Luis. This happens since 9c5ccf2db04b ("mm: remove HUGETLB_PAGE_DTOR") effectively added some VM_BUG_ON() checks in the PageHuge() testing path. [willy@infradead.org: update vmcoreinfo]

In the Linux kernel, the following vulnerability has been resolved: mm/mremap: fix address wraparound in move_page_tables() On 32-bit platforms, it is possible for the expression `len + old_addr < old_end` to be false-positive if `len + old_addr` wraps around. `old_addr` is the cursor in the old range up to which page table entries have been moved; so if the operation succeeded, `old_addr` is the *end* of the old region, and adding `len` to it can wrap. The overflow causes mremap() to mistakenly believe that PTEs have been copied; the consequence is that mremap() bails out, but doesn't move the PTEs back before the new VMA is unmapped, causing anonymous pages in the region to be lost. So basically if userspace tries to mremap() a private-anon region and hits this bug, mremap() will return an error and the private-anon region's contents appear to have been zeroed. The idea of this check is that `old_end - len` is the original start address, and writing the check that way also makes it easier to read; so fix the check by rearranging the comparison accordingly. (An alternate fix would be to refactor this function by introducing an "orig_old_start" variable or such.) Tested in a VM with a 32-bit X86 kernel; without the patch: ``` user@horn:~/big_mremap$ cat test.c #define _GNU_SOURCE #include <stdlib.h> #include <stdio.h> #include <err.h> #include <sys/mman.h> #define ADDR1 ((void*)0x60000000) #define ADDR2 ((void*)0x10000000) #define SIZE 0x50000000uL int main(void) { unsigned char *p1 = mmap(ADDR1, SIZE, PROT_READ|PROT_WRITE, MAP_ANONYMOUS|MAP_PRIVATE|MAP_FIXED_NOREPLACE, -1, 0); if (p1 == MAP_FAILED) err(1, "mmap 1"); unsigned char *p2 = mmap(ADDR2, SIZE, PROT_NONE, MAP_ANONYMOUS|MAP_PRIVATE|MAP_FIXED_NOREPLACE, -1, 0); if (p2 == MAP_FAILED) err(1, "mmap 2"); *p1 = 0x41; printf("first char is 0x%02hhx\n", *p1); unsigned char *p3 = mremap(p1, SIZE, SIZE, MREMAP_MAYMOVE|MREMAP_FIXED, p2); if (p3 == MAP_FAILED) { printf("mremap() failed; first char is 0x%02hhx\n", *p1); } else { printf("mremap() succeeded; first char is 0x%02hhx\n", *p3); } } user@horn:~/big_mremap$ gcc -static -o test test.c user@horn:~/big_mremap$ setarch -R ./test first char is 0x41 mremap() failed; first char is 0x00 ``` With the patch: ``` user@horn:~/big_mremap$ setarch -R ./test first char is 0x41 mremap() succeeded; first char is 0x41 ```

In the Linux kernel, the following vulnerability has been resolved: spi: spi-fsl-dspi: Fix crash when not using GPIO chip select Add check for the return value of spi_get_csgpiod() to avoid passing a NULL pointer to gpiod_direction_output(), preventing a crash when GPIO chip select is not used. Fix below crash: [ 4.251960] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 4.260762] Mem abort info: [ 4.263556] ESR = 0x0000000096000004 [ 4.267308] EC = 0x25: DABT (current EL), IL = 32 bits [ 4.272624] SET = 0, FnV = 0 [ 4.275681] EA = 0, S1PTW = 0 [ 4.278822] FSC = 0x04: level 0 translation fault [ 4.283704] Data abort info: [ 4.286583] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [ 4.292074] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 4.297130] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 4.302445] [0000000000000000] user address but active_mm is swapper [ 4.308805] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP [ 4.315072] Modules linked in: [ 4.318124] CPU: 2 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.0-rc4-next-20241023-00008-ga20ec42c5fc1 #359 [ 4.328130] Hardware name: LS1046A QDS Board (DT) [ 4.332832] pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 4.339794] pc : gpiod_direction_output+0x34/0x5c [ 4.344505] lr : gpiod_direction_output+0x18/0x5c [ 4.349208] sp : ffff80008003b8f0 [ 4.352517] x29: ffff80008003b8f0 x28: 0000000000000000 x27: ffffc96bcc7e9068 [ 4.359659] x26: ffffc96bcc6e00b0 x25: ffffc96bcc598398 x24: ffff447400132810 [ 4.366800] x23: 0000000000000000 x22: 0000000011e1a300 x21: 0000000000020002 [ 4.373940] x20: 0000000000000000 x19: 0000000000000000 x18: ffffffffffffffff [ 4.381081] x17: ffff44740016e600 x16: 0000000500000003 x15: 0000000000000007 [ 4.388221] x14: 0000000000989680 x13: 0000000000020000 x12: 000000000000001e [ 4.395362] x11: 0044b82fa09b5a53 x10: 0000000000000019 x9 : 0000000000000008 [ 4.402502] x8 : 0000000000000002 x7 : 0000000000000007 x6 : 0000000000000000 [ 4.409641] x5 : 0000000000000200 x4 : 0000000002000000 x3 : 0000000000000000 [ 4.416781] x2 : 0000000000022202 x1 : 0000000000000000 x0 : 0000000000000000 [ 4.423921] Call trace: [ 4.426362] gpiod_direction_output+0x34/0x5c (P) [ 4.431067] gpiod_direction_output+0x18/0x5c (L) [ 4.435771] dspi_setup+0x220/0x334

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Fix incorrect pci_for_each_dma_alias() for non-PCI devices Previously, the domain_context_clear() function incorrectly called pci_for_each_dma_alias() to set up context entries for non-PCI devices. This could lead to kernel hangs or other unexpected behavior. Add a check to only call pci_for_each_dma_alias() for PCI devices. For non-PCI devices, domain_context_clear_one() is called directly.

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix rxrpc_local leak in rxrpc_lookup_peer() Need to call rxrpc_put_local() for peer candidate before kfree() as it holds a ref to rxrpc_local. [DH: v2: Changed to abstract the peer freeing code out into a function]

In the Linux kernel, the following vulnerability has been resolved: thermal/drivers/cpufreq_cooling: Fix slab OOB issue Slab OOB issue is scanned by KASAN in cpu_power_to_freq(). If power is limited below the power of OPP0 in EM table, it will cause slab out-of-bound issue with negative array index. Return the lowest frequency if limited power cannot found a suitable OPP in EM table to fix this issue. Backtrace: [<ffffffd02d2a37f0>] die+0x104/0x5ac [<ffffffd02d2a5630>] bug_handler+0x64/0xd0 [<ffffffd02d288ce4>] brk_handler+0x160/0x258 [<ffffffd02d281e5c>] do_debug_exception+0x248/0x3f0 [<ffffffd02d284488>] el1_dbg+0x14/0xbc [<ffffffd02d75d1d4>] __kasan_report+0x1dc/0x1e0 [<ffffffd02d75c2e0>] kasan_report+0x10/0x20 [<ffffffd02d75def8>] __asan_report_load8_noabort+0x18/0x28 [<ffffffd02e6fce5c>] cpufreq_power2state+0x180/0x43c [<ffffffd02e6ead80>] power_actor_set_power+0x114/0x1d4 [<ffffffd02e6fac24>] allocate_power+0xaec/0xde0 [<ffffffd02e6f9f80>] power_allocator_throttle+0x3ec/0x5a4 [<ffffffd02e6ea888>] handle_thermal_trip+0x160/0x294 [<ffffffd02e6edd08>] thermal_zone_device_check+0xe4/0x154 [<ffffffd02d351cb4>] process_one_work+0x5e4/0xe28 [<ffffffd02d352f44>] worker_thread+0xa4c/0xfac [<ffffffd02d360124>] kthread+0x33c/0x358 [<ffffffd02d289940>] ret_from_fork+0xc/0x18

In the Linux kernel, the following vulnerability has been resolved: sfc: Don't invoke xdp_do_flush() from netpoll. Yury reported a crash in the sfc driver originated from netpoll_send_udp(). The netconsole sends a message and then netpoll invokes the driver's NAPI function with a budget of zero. It is dedicated to allow driver to free TX resources, that it may have used while sending the packet. In the netpoll case the driver invokes xdp_do_flush() unconditionally, leading to crash because bpf_net_context was never assigned. Invoke xdp_do_flush() only if budget is not zero.

In the Linux kernel, the following vulnerability has been resolved: powerpc/32: Fix hardlockup on vmap stack overflow Since the commit c118c7303ad5 ("powerpc/32: Fix vmap stack - Do not activate MMU before reading task struct") a vmap stack overflow results in a hard lockup. This is because emergency_ctx is still addressed with its virtual address allthough data MMU is not active anymore at that time. Fix it by using a physical address instead.

In the Linux kernel, the following vulnerability has been resolved: soc: qcom: geni-se: fix array underflow in geni_se_clk_tbl_get() This loop is supposed to break if the frequency returned from clk_round_rate() is the same as on the previous iteration. However, that check doesn't make sense on the first iteration through the loop. It leads to reading before the start of these->clk_perf_tbl[] array.

In the Linux kernel, the following vulnerability has been resolved: RDMA/bnxt_re: Fix a bug while setting up Level-2 PBL pages Avoid memory corruption while setting up Level-2 PBL pages for the non MR resources when num_pages > 256K. There will be a single PDE page address (contiguous pages in the case of > PAGE_SIZE), but, current logic assumes multiple pages, leading to invalid memory access after 256K PBL entries in the PDE.

An issue was discovered in the FUSE filesystem implementation in the Linux kernel before 5.10.6, aka CID-5d069dbe8aaf. fuse_do_getattr() calls make_bad_inode() in inappropriate situations, causing a system crash. NOTE: the original fix for this vulnerability was incomplete, and its incompleteness is tracked as CVE-2021-28950.

In the Linux kernel, the following vulnerability has been resolved: ACPI: PRM: Find EFI_MEMORY_RUNTIME block for PRM handler and context PRMT needs to find the correct type of block to translate the PA-VA mapping for EFI runtime services. The issue arises because the PRMT is finding a block of type EFI_CONVENTIONAL_MEMORY, which is not appropriate for runtime services as described in Section 2.2.2 (Runtime Services) of the UEFI Specification [1]. Since the PRM handler is a type of runtime service, this causes an exception when the PRM handler is called. [Firmware Bug]: Unable to handle paging request in EFI runtime service WARNING: CPU: 22 PID: 4330 at drivers/firmware/efi/runtime-wrappers.c:341 __efi_queue_work+0x11c/0x170 Call trace: Let PRMT find a block with EFI_MEMORY_RUNTIME for PRM handler and PRM context. If no suitable block is found, a warning message will be printed, but the procedure continues to manage the next PRM handler. However, if the PRM handler is actually called without proper allocation, it would result in a failure during error handling. By using the correct memory types for runtime services, ensure that the PRM handler and the context are properly mapped in the virtual address space during runtime, preventing the paging request error. The issue is really that only memory that has been remapped for runtime by the firmware can be used by the PRM handler, and so the region needs to have the EFI_MEMORY_RUNTIME attribute. [ rjw: Subject and changelog edits ]

In the Linux kernel, the following vulnerability has been resolved: net: stmmac: TSO: Fix unbalanced DMA map/unmap for non-paged SKB data In case the non-paged data of a SKB carries protocol header and protocol payload to be transmitted on a certain platform that the DMA AXI address width is configured to 40-bit/48-bit, or the size of the non-paged data is bigger than TSO_MAX_BUFF_SIZE on a certain platform that the DMA AXI address width is configured to 32-bit, then this SKB requires at least two DMA transmit descriptors to serve it. For example, three descriptors are allocated to split one DMA buffer mapped from one piece of non-paged data: dma_desc[N + 0], dma_desc[N + 1], dma_desc[N + 2]. Then three elements of tx_q->tx_skbuff_dma[] will be allocated to hold extra information to be reused in stmmac_tx_clean(): tx_q->tx_skbuff_dma[N + 0], tx_q->tx_skbuff_dma[N + 1], tx_q->tx_skbuff_dma[N + 2]. Now we focus on tx_q->tx_skbuff_dma[entry].buf, which is the DMA buffer address returned by DMA mapping call. stmmac_tx_clean() will try to unmap the DMA buffer _ONLY_IF_ tx_q->tx_skbuff_dma[entry].buf is a valid buffer address. The expected behavior that saves DMA buffer address of this non-paged data to tx_q->tx_skbuff_dma[entry].buf is: tx_q->tx_skbuff_dma[N + 0].buf = NULL; tx_q->tx_skbuff_dma[N + 1].buf = NULL; tx_q->tx_skbuff_dma[N + 2].buf = dma_map_single(); Unfortunately, the current code misbehaves like this: tx_q->tx_skbuff_dma[N + 0].buf = dma_map_single(); tx_q->tx_skbuff_dma[N + 1].buf = NULL; tx_q->tx_skbuff_dma[N + 2].buf = NULL; On the stmmac_tx_clean() side, when dma_desc[N + 0] is closed by the DMA engine, tx_q->tx_skbuff_dma[N + 0].buf is a valid buffer address obviously, then the DMA buffer will be unmapped immediately. There may be a rare case that the DMA engine does not finish the pending dma_desc[N + 1], dma_desc[N + 2] yet. Now things will go horribly wrong, DMA is going to access a unmapped/unreferenced memory region, corrupted data will be transmited or iommu fault will be triggered :( In contrast, the for-loop that maps SKB fragments behaves perfectly as expected, and that is how the driver should do for both non-paged data and paged frags actually. This patch corrects DMA map/unmap sequences by fixing the array index for tx_q->tx_skbuff_dma[entry].buf when assigning DMA buffer address. Tested and verified on DWXGMAC CORE 3.20a

In the Linux kernel, the following vulnerability has been resolved: clk: qcom: videocc-sm8350: use HW_CTRL_TRIGGER for vcodec GDSCs A recent change in the venus driver results in a stuck clock on the Lenovo ThinkPad X13s, for example, when streaming video in firefox: video_cc_mvs0_clk status stuck at 'off' WARNING: CPU: 6 PID: 2885 at drivers/clk/qcom/clk-branch.c:87 clk_branch_wait+0x144/0x15c ... Call trace: clk_branch_wait+0x144/0x15c clk_branch2_enable+0x30/0x40 clk_core_enable+0xd8/0x29c clk_enable+0x2c/0x4c vcodec_clks_enable.isra.0+0x94/0xd8 [venus_core] coreid_power_v4+0x464/0x628 [venus_core] vdec_start_streaming+0xc4/0x510 [venus_dec] vb2_start_streaming+0x6c/0x180 [videobuf2_common] vb2_core_streamon+0x120/0x1dc [videobuf2_common] vb2_streamon+0x1c/0x6c [videobuf2_v4l2] v4l2_m2m_ioctl_streamon+0x30/0x80 [v4l2_mem2mem] v4l_streamon+0x24/0x30 [videodev] using the out-of-tree sm8350/sc8280xp venus support. [1] Update also the sm8350/sc8280xp GDSC definitions so that the hw control mode can be changed at runtime as the venus driver now requires.