In the Linux kernel, the following vulnerability has been resolved: trace_events_hist: add check for return value of 'create_hist_field' Function 'create_hist_field' is called recursively at trace_events_hist.c:1954 and can return NULL-value that's why we have to check it to avoid null pointer dereference. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: can: gs_usb: fix time stamp counter initialization If the gs_usb device driver is unloaded (or unbound) before the interface is shut down, the USB stack first calls the struct usb_driver::disconnect and then the struct net_device_ops::ndo_stop callback. In gs_usb_disconnect() all pending bulk URBs are killed, i.e. no more RX'ed CAN frames are send from the USB device to the host. Later in gs_can_close() a reset control message is send to each CAN channel to remove the controller from the CAN bus. In this race window the USB device can still receive CAN frames from the bus and internally queue them to be send to the host. At least in the current version of the candlelight firmware, the queue of received CAN frames is not emptied during the reset command. After loading (or binding) the gs_usb driver, new URBs are submitted during the struct net_device_ops::ndo_open callback and the candlelight firmware starts sending its already queued CAN frames to the host. However, this scenario was not considered when implementing the hardware timestamp function. The cycle counter/time counter infrastructure is set up (gs_usb_timestamp_init()) after the USBs are submitted, resulting in a NULL pointer dereference if timecounter_cyc2time() (via the call chain: gs_usb_receive_bulk_callback() -> gs_usb_set_timestamp() -> gs_usb_skb_set_timestamp()) is called too early. Move the gs_usb_timestamp_init() function before the URBs are submitted to fix this problem. For a comprehensive solution, we need to consider gs_usb devices with more than 1 channel. The cycle counter/time counter infrastructure is setup per channel, but the RX URBs are per device. Once gs_can_open() of _a_ channel has been called, and URBs have been submitted, the gs_usb_receive_bulk_callback() can be called for _all_ available channels, even for channels that are not running, yet. As cycle counter/time counter has not set up, this will again lead to a NULL pointer dereference. Convert the cycle counter/time counter from a "per channel" to a "per device" functionality. Also set it up, before submitting any URBs to the device. Further in gs_usb_receive_bulk_callback(), don't process any URBs for not started CAN channels, only resubmit the URB.

In the Linux kernel, the following vulnerability has been resolved: drm/msm: another fix for the headless Adreno GPU Fix another oops reproducible when rebooting the board with the Adreno GPU working in the headless mode (e.g. iMX platforms). Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read [00000000] *pgd=74936831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] ARM CPU: 0 PID: 51 Comm: reboot Not tainted 6.2.0-rc1-dirty #11 Hardware name: Freescale i.MX53 (Device Tree Support) PC is at msm_atomic_commit_tail+0x50/0x970 LR is at commit_tail+0x9c/0x188 pc : [<c06aa430>] lr : [<c067a214>] psr: 600e0013 sp : e0851d30 ip : ee4eb7eb fp : 00090acc r10: 00000058 r9 : c2193014 r8 : c4310000 r7 : c4759380 r6 : 07bef61d r5 : 00000000 r4 : 00000000 r3 : c44cc440 r2 : 00000000 r1 : 00000000 r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 74910019 DAC: 00000051 Register r0 information: NULL pointer Register r1 information: NULL pointer Register r2 information: NULL pointer Register r3 information: slab kmalloc-1k start c44cc400 pointer offset 64 size 1024 Register r4 information: NULL pointer Register r5 information: NULL pointer Register r6 information: non-paged memory Register r7 information: slab kmalloc-128 start c4759380 pointer offset 0 size 128 Register r8 information: slab kmalloc-2k start c4310000 pointer offset 0 size 2048 Register r9 information: non-slab/vmalloc memory Register r10 information: non-paged memory Register r11 information: non-paged memory Register r12 information: non-paged memory Process reboot (pid: 51, stack limit = 0xc80046d9) Stack: (0xe0851d30 to 0xe0852000) 1d20: c4759380 fbd77200 000005ff 002b9c70 1d40: c4759380 c4759380 00000000 07bef61d 00000600 c0d6fe7c c2193014 00000058 1d60: 00090acc c067a214 00000000 c4759380 c4310000 00000000 c44cc854 c067a89c 1d80: 00000000 00000000 00000000 c4310468 00000000 c4759380 c4310000 c4310468 1da0: c4310470 c0643258 c4759380 00000000 00000000 c0c4ee24 00000000 c44cc810 1dc0: 00000000 c0c4ee24 00000000 c44cc810 00000000 0347d2a8 e0851e00 e0851e00 1de0: c4759380 c067ad20 c4310000 00000000 c44cc810 c27f8718 c44cc854 c067adb8 1e00: c4933000 00000002 00000001 00000000 00000000 c2130850 00000000 c2130854 1e20: c25fc488 00000000 c0ff162c 00000000 00000001 00000002 00000000 00000000 1e40: c43102c0 c43102c0 00000000 0347d2a8 c44cc810 c44cc814 c2133da8 c06d1a60 1e60: 00000000 00000000 00079028 c2012f24 fee1dead c4933000 00000058 c01431e4 1e80: 01234567 c0143a20 00000000 00000000 00000000 00000000 00000000 00000000 1ea0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 1ec0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 1ee0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 1f00: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 1f20: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 1f40: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 1f60: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 1f80: 00000000 00000000 00000000 0347d2a8 00000002 00000004 00000078 00000058 1fa0: c010028c c0100060 00000002 00000004 fee1dead 28121969 01234567 00079028 1fc0: 00000002 00000004 00000078 00000058 0002fdc5 00000000 00000000 00090acc 1fe0: 00000058 becc9c64 b6e97e05 b6e0e5f6 600e0030 fee1dead 00000000 00000000 msm_atomic_commit_tail from commit_tail+0x9c/0x188 commit_tail from drm_atomic_helper_commit+0x160/0x188 drm_atomic_helper_commit from drm_atomic_commit+0xac/0xe0 drm_atomic_commit from drm_atomic_helper_disable_all+0x1b0/0x1c0 drm_atomic_helper_disable_all from drm_atomic_helper_shutdown+0x88/0x140 drm_atomic_helper_shutdown from device_shutdown+0x16c/0x240 device_shutdown from kernel_restart+0x38/0x90 kernel_restart from __do_sys_reboot+0x ---truncated---

In the Linux kernel, the following vulnerability has been resolved: tracing: Have trace_event_file have ref counters The following can crash the kernel: # cd /sys/kernel/tracing # echo 'p:sched schedule' > kprobe_events # exec 5>>events/kprobes/sched/enable # > kprobe_events # exec 5>&- The above commands: 1. Change directory to the tracefs directory 2. Create a kprobe event (doesn't matter what one) 3. Open bash file descriptor 5 on the enable file of the kprobe event 4. Delete the kprobe event (removes the files too) 5. Close the bash file descriptor 5 The above causes a crash! BUG: kernel NULL pointer dereference, address: 0000000000000028 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 6 PID: 877 Comm: bash Not tainted 6.5.0-rc4-test-00008-g2c6b6b1029d4-dirty #186 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-debian-1.16.2-1 04/01/2014 RIP: 0010:tracing_release_file_tr+0xc/0x50 What happens here is that the kprobe event creates a trace_event_file "file" descriptor that represents the file in tracefs to the event. It maintains state of the event (is it enabled for the given instance?). Opening the "enable" file gets a reference to the event "file" descriptor via the open file descriptor. When the kprobe event is deleted, the file is also deleted from the tracefs system which also frees the event "file" descriptor. But as the tracefs file is still opened by user space, it will not be totally removed until the final dput() is called on it. But this is not true with the event "file" descriptor that is already freed. If the user does a write to or simply closes the file descriptor it will reference the event "file" descriptor that was just freed, causing a use-after-free bug. To solve this, add a ref count to the event "file" descriptor as well as a new flag called "FREED". The "file" will not be freed until the last reference is released. But the FREE flag will be set when the event is removed to prevent any more modifications to that event from happening, even if there's still a reference to the event "file" descriptor.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btusb: Add date->evt_skb is NULL check fix crash because of null pointers [ 6104.969662] BUG: kernel NULL pointer dereference, address: 00000000000000c8 [ 6104.969667] #PF: supervisor read access in kernel mode [ 6104.969668] #PF: error_code(0x0000) - not-present page [ 6104.969670] PGD 0 P4D 0 [ 6104.969673] Oops: 0000 [#1] SMP NOPTI [ 6104.969684] RIP: 0010:btusb_mtk_hci_wmt_sync+0x144/0x220 [btusb] [ 6104.969688] RSP: 0018:ffffb8d681533d48 EFLAGS: 00010246 [ 6104.969689] RAX: 0000000000000000 RBX: ffff8ad560bb2000 RCX: 0000000000000006 [ 6104.969691] RDX: 0000000000000000 RSI: ffffb8d681533d08 RDI: 0000000000000000 [ 6104.969692] RBP: ffffb8d681533d70 R08: 0000000000000001 R09: 0000000000000001 [ 6104.969694] R10: 0000000000000001 R11: 00000000fa83b2da R12: ffff8ad461d1d7c0 [ 6104.969695] R13: 0000000000000000 R14: ffff8ad459618c18 R15: ffffb8d681533d90 [ 6104.969697] FS: 00007f5a1cab9d40(0000) GS:ffff8ad578200000(0000) knlGS:00000 [ 6104.969699] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 6104.969700] CR2: 00000000000000c8 CR3: 000000018620c001 CR4: 0000000000760ef0 [ 6104.969701] PKRU: 55555554 [ 6104.969702] Call Trace: [ 6104.969708] btusb_mtk_shutdown+0x44/0x80 [btusb] [ 6104.969732] hci_dev_do_close+0x470/0x5c0 [bluetooth] [ 6104.969748] hci_rfkill_set_block+0x56/0xa0 [bluetooth] [ 6104.969753] rfkill_set_block+0x92/0x160 [ 6104.969755] rfkill_fop_write+0x136/0x1e0 [ 6104.969759] __vfs_write+0x18/0x40 [ 6104.969761] vfs_write+0xdf/0x1c0 [ 6104.969763] ksys_write+0xb1/0xe0 [ 6104.969765] __x64_sys_write+0x1a/0x20 [ 6104.969769] do_syscall_64+0x51/0x180 [ 6104.969771] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 6104.969773] RIP: 0033:0x7f5a21f18fef [ 6104.9] RSP: 002b:00007ffeefe39010 EFLAGS: 00000293 ORIG_RAX: 0000000000000001 [ 6104.969780] RAX: ffffffffffffffda RBX: 000055c10a7560a0 RCX: 00007f5a21f18fef [ 6104.969781] RDX: 0000000000000008 RSI: 00007ffeefe39060 RDI: 0000000000000012 [ 6104.969782] RBP: 00007ffeefe39060 R08: 0000000000000000 R09: 0000000000000017 [ 6104.969784] R10: 00007ffeefe38d97 R11: 0000000000000293 R12: 0000000000000002 [ 6104.969785] R13: 00007ffeefe39220 R14: 00007ffeefe391a0 R15: 000055c10a72acf0

In the Linux kernel, the following vulnerability has been resolved: icmp6: Fix null-ptr-deref of ip6_null_entry->rt6i_idev in icmp6_dev(). With some IPv6 Ext Hdr (RPL, SRv6, etc.), we can send a packet that has the link-local address as src and dst IP and will be forwarded to an external IP in the IPv6 Ext Hdr. For example, the script below generates a packet whose src IP is the link-local address and dst is updated to 11::. # for f in $(find /proc/sys/net/ -name *seg6_enabled*); do echo 1 > $f; done # python3 >>> from socket import * >>> from scapy.all import * >>> >>> SRC_ADDR = DST_ADDR = "fe80::5054:ff:fe12:3456" >>> >>> pkt = IPv6(src=SRC_ADDR, dst=DST_ADDR) >>> pkt /= IPv6ExtHdrSegmentRouting(type=4, addresses=["11::", "22::"], segleft=1) >>> >>> sk = socket(AF_INET6, SOCK_RAW, IPPROTO_RAW) >>> sk.sendto(bytes(pkt), (DST_ADDR, 0)) For such a packet, we call ip6_route_input() to look up a route for the next destination in these three functions depending on the header type. * ipv6_rthdr_rcv() * ipv6_rpl_srh_rcv() * ipv6_srh_rcv() If no route is found, ip6_null_entry is set to skb, and the following dst_input(skb) calls ip6_pkt_drop(). Finally, in icmp6_dev(), we dereference skb_rt6_info(skb)->rt6i_idev->dev as the input device is the loopback interface. Then, we have to check if skb_rt6_info(skb)->rt6i_idev is NULL or not to avoid NULL pointer deref for ip6_null_entry. BUG: kernel NULL pointer dereference, address: 0000000000000000 PF: supervisor read access in kernel mode PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 0 PID: 157 Comm: python3 Not tainted 6.4.0-11996-gb121d614371c #35 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:icmp6_send (net/ipv6/icmp.c:436 net/ipv6/icmp.c:503) Code: fe ff ff 48 c7 40 30 c0 86 5d 83 e8 c6 44 1c 00 e9 c8 fc ff ff 49 8b 46 58 48 83 e0 fe 0f 84 4a fb ff ff 48 8b 80 d0 00 00 00 <48> 8b 00 44 8b 88 e0 00 00 00 e9 34 fb ff ff 4d 85 ed 0f 85 69 01 RSP: 0018:ffffc90000003c70 EFLAGS: 00000286 RAX: 0000000000000000 RBX: 0000000000000001 RCX: 00000000000000e0 RDX: 0000000000000021 RSI: 0000000000000000 RDI: ffff888006d72a18 RBP: ffffc90000003d80 R08: 0000000000000000 R09: 0000000000000001 R10: ffffc90000003d98 R11: 0000000000000040 R12: ffff888006d72a10 R13: 0000000000000000 R14: ffff8880057fb800 R15: ffffffff835d86c0 FS: 00007f9dc72ee740(0000) GS:ffff88807dc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 00000000057b2000 CR4: 00000000007506f0 PKRU: 55555554 Call Trace: <IRQ> ip6_pkt_drop (net/ipv6/route.c:4513) ipv6_rthdr_rcv (net/ipv6/exthdrs.c:640 net/ipv6/exthdrs.c:686) ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:437 (discriminator 5)) ip6_input_finish (./include/linux/rcupdate.h:781 net/ipv6/ip6_input.c:483) __netif_receive_skb_one_core (net/core/dev.c:5455) process_backlog (./include/linux/rcupdate.h:781 net/core/dev.c:5895) __napi_poll (net/core/dev.c:6460) net_rx_action (net/core/dev.c:6529 net/core/dev.c:6660) __do_softirq (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/irq.h:142 kernel/softirq.c:554) do_softirq (kernel/softirq.c:454 kernel/softirq.c:441) </IRQ> <TASK> __local_bh_enable_ip (kernel/softirq.c:381) __dev_queue_xmit (net/core/dev.c:4231) ip6_finish_output2 (./include/net/neighbour.h:544 net/ipv6/ip6_output.c:135) rawv6_sendmsg (./include/net/dst.h:458 ./include/linux/netfilter.h:303 net/ipv6/raw.c:656 net/ipv6/raw.c:914) sock_sendmsg (net/socket.c:725 net/socket.c:748) __sys_sendto (net/socket.c:2134) __x64_sys_sendto (net/socket.c:2146 net/socket.c:2142 net/socket.c:2142) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) RIP: 0033:0x7f9dc751baea Code: d8 64 89 02 48 c7 c0 ff f ---truncated---

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: ensure CLM version is null-terminated to prevent stack-out-of-bounds Fix a stack-out-of-bounds read in brcmfmac that occurs when 'buf' that is not null-terminated is passed as an argument of strreplace() in brcmf_c_preinit_dcmds(). This buffer is filled with a CLM version string by memcpy() in brcmf_fil_iovar_data_get(). Ensure buf is null-terminated. Found by a modified version of syzkaller. [ 33.004414][ T1896] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available [ 33.013486][ T1896] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43236/3 wl0: Nov 30 2011 17:33:42 version 5.90.188.22 [ 33.021554][ T1896] ================================================================== [ 33.022379][ T1896] BUG: KASAN: stack-out-of-bounds in strreplace+0xf2/0x110 [ 33.023122][ T1896] Read of size 1 at addr ffffc90001d6efc8 by task kworker/0:2/1896 [ 33.023852][ T1896] [ 33.024096][ T1896] CPU: 0 PID: 1896 Comm: kworker/0:2 Tainted: G O 5.14.0+ #132 [ 33.024927][ T1896] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 33.026065][ T1896] Workqueue: usb_hub_wq hub_event [ 33.026581][ T1896] Call Trace: [ 33.026896][ T1896] dump_stack_lvl+0x57/0x7d [ 33.027372][ T1896] print_address_description.constprop.0.cold+0xf/0x334 [ 33.028037][ T1896] ? strreplace+0xf2/0x110 [ 33.028403][ T1896] ? strreplace+0xf2/0x110 [ 33.028807][ T1896] kasan_report.cold+0x83/0xdf [ 33.029283][ T1896] ? strreplace+0xf2/0x110 [ 33.029666][ T1896] strreplace+0xf2/0x110 [ 33.029966][ T1896] brcmf_c_preinit_dcmds+0xab1/0xc40 [ 33.030351][ T1896] ? brcmf_c_set_joinpref_default+0x100/0x100 [ 33.030787][ T1896] ? rcu_read_lock_sched_held+0xa1/0xd0 [ 33.031223][ T1896] ? rcu_read_lock_bh_held+0xb0/0xb0 [ 33.031661][ T1896] ? lock_acquire+0x19d/0x4e0 [ 33.032091][ T1896] ? find_held_lock+0x2d/0x110 [ 33.032605][ T1896] ? brcmf_usb_deq+0x1a7/0x260 [ 33.033087][ T1896] ? brcmf_usb_rx_fill_all+0x5a/0xf0 [ 33.033582][ T1896] brcmf_attach+0x246/0xd40 [ 33.034022][ T1896] ? wiphy_new_nm+0x1476/0x1d50 [ 33.034383][ T1896] ? kmemdup+0x30/0x40 [ 33.034722][ T1896] brcmf_usb_probe+0x12de/0x1690 [ 33.035223][ T1896] ? brcmf_usbdev_qinit.constprop.0+0x470/0x470 [ 33.035833][ T1896] usb_probe_interface+0x25f/0x710 [ 33.036315][ T1896] really_probe+0x1be/0xa90 [ 33.036656][ T1896] __driver_probe_device+0x2ab/0x460 [ 33.037026][ T1896] ? usb_match_id.part.0+0x88/0xc0 [ 33.037383][ T1896] driver_probe_device+0x49/0x120 [ 33.037790][ T1896] __device_attach_driver+0x18a/0x250 [ 33.038300][ T1896] ? driver_allows_async_probing+0x120/0x120 [ 33.038986][ T1896] bus_for_each_drv+0x123/0x1a0 [ 33.039906][ T1896] ? bus_rescan_devices+0x20/0x20 [ 33.041412][ T1896] ? lockdep_hardirqs_on_prepare+0x273/0x3e0 [ 33.041861][ T1896] ? trace_hardirqs_on+0x1c/0x120 [ 33.042330][ T1896] __device_attach+0x207/0x330 [ 33.042664][ T1896] ? device_bind_driver+0xb0/0xb0 [ 33.043026][ T1896] ? kobject_uevent_env+0x230/0x12c0 [ 33.043515][ T1896] bus_probe_device+0x1a2/0x260 [ 33.043914][ T1896] device_add+0xa61/0x1ce0 [ 33.044227][ T1896] ? __mutex_unlock_slowpath+0xe7/0x660 [ 33.044891][ T1896] ? __fw_devlink_link_to_suppliers+0x550/0x550 [ 33.045531][ T1896] usb_set_configuration+0x984/0x1770 [ 33.046051][ T1896] ? kernfs_create_link+0x175/0x230 [ 33.046548][ T1896] usb_generic_driver_probe+0x69/0x90 [ 33.046931][ T1896] usb_probe_device+0x9c/0x220 [ 33.047434][ T1896] really_probe+0x1be/0xa90 [ 33.047760][ T1896] __driver_probe_device+0x2ab/0x460 [ 33.048134][ T1896] driver_probe_device+0x49/0x120 [ 33.048516][ T1896] __device_attach_driver+0x18a/0x250 [ 33.048910][ T1896] ? driver_allows_async_probing+0x120/0x120 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: blk-cgroup: Reinit blkg_iostat_set after clearing in blkcg_reset_stats() When blkg_alloc() is called to allocate a blkcg_gq structure with the associated blkg_iostat_set's, there are 2 fields within blkg_iostat_set that requires proper initialization - blkg & sync. The former field was introduced by commit 3b8cc6298724 ("blk-cgroup: Optimize blkcg_rstat_flush()") while the later one was introduced by commit f73316482977 ("blk-cgroup: reimplement basic IO stats using cgroup rstat"). Unfortunately those fields in the blkg_iostat_set's are not properly re-initialized when they are cleared in v1's blkcg_reset_stats(). This can lead to a kernel panic due to NULL pointer access of the blkg pointer. The missing initialization of sync is less problematic and can be a problem in a debug kernel due to missing lockdep initialization. Fix these problems by re-initializing them after memory clearing.

In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: avoid possible NULL skb pointer dereference In 'mwifiex_handle_uap_rx_forward()', always check the value returned by 'skb_copy()' to avoid potential NULL pointer dereference in 'mwifiex_uap_queue_bridged_pkt()', and drop original skb in case of copying failure. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: u_serial: Add null pointer check in gserial_suspend Consider a case where gserial_disconnect has already cleared gser->ioport. And if gserial_suspend gets called afterwards, it will lead to accessing of gser->ioport and thus causing null pointer dereference. Avoid this by adding a null pointer check. Added a static spinlock to prevent gser->ioport from becoming null after the newly added null pointer check.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: E-Switch, Fix an Oops in error handling code The error handling dereferences "vport". There is nothing we can do if it is an error pointer except returning the error code.

In the Linux kernel, the following vulnerability has been resolved: dm stats: check for and propagate alloc_percpu failure Check alloc_precpu()'s return value and return an error from dm_stats_init() if it fails. Update alloc_dev() to fail if dm_stats_init() does. Otherwise, a NULL pointer dereference will occur in dm_stats_cleanup() even if dm-stats isn't being actively used.

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: mtk_drm_crtc: Add checks for devm_kcalloc As the devm_kcalloc may return NULL, the return value needs to be checked to avoid NULL poineter dereference.

In the Linux kernel, the following vulnerability has been resolved: octeontx2-pf: handle otx2_mbox_get_rsp errors in otx2_flows.c Adding error pointer check after calling otx2_mbox_get_rsp().

In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_set_rbtree: fix overlap expiration walk The lazy gc on insert that should remove timed-out entries fails to release the other half of the interval, if any. Can be reproduced with tests/shell/testcases/sets/0044interval_overlap_0 in nftables.git and kmemleak enabled kernel. Second bug is the use of rbe_prev vs. prev pointer. If rbe_prev() returns NULL after at least one iteration, rbe_prev points to element that is not an end interval, hence it should not be removed. Lastly, check the genmask of the end interval if this is active in the current generation.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Fix possible NULL pointer dereference in snd_usb_pcm_has_fixed_rate() The subs function argument may be NULL, so do not use it before the NULL check.

In the Linux kernel, the following vulnerability has been resolved: usb: ucsi_acpi: Increase the command completion timeout Commit 130a96d698d7 ("usb: typec: ucsi: acpi: Increase command completion timeout value") increased the timeout from 5 seconds to 60 seconds due to issues related to alternate mode discovery. After the alternate mode discovery switch to polled mode the timeout was reduced, but instead of being set back to 5 seconds it was reduced to 1 second. This is causing problems when using a Lenovo ThinkPad X1 yoga gen7 connected over Type-C to a LG 27UL850-W (charging DP over Type-C). When the monitor is already connected at boot the following error is logged: "PPM init failed (-110)", /sys/class/typec is empty and on unplugging the NULL pointer deref fixed earlier in this series happens. When the monitor is connected after boot the following error is logged instead: "GET_CONNECTOR_STATUS failed (-110)". Setting the timeout back to 5 seconds fixes both cases.

In the Linux kernel, the following vulnerability has been resolved: ACPI: processor: Check for null return of devm_kzalloc() in fch_misc_setup() devm_kzalloc() may fail, clk_data->name might be NULL and will cause a NULL pointer dereference later. [ rjw: Subject and changelog edits ]

In the Linux kernel, the following vulnerability has been resolved: regulator: da9063: better fix null deref with partial DT Two versions of the original patch were sent but V1 was merged instead of V2 due to a mistake. So update to V2. The advantage of V2 is that it completely avoids dereferencing the pointer, even just to take the address, which may fix problems with some compilers. Both versions work on my gcc 9.4 but use the safer one.

In the Linux kernel, the following vulnerability has been resolved: scsi: iscsi_tcp: Check that sock is valid before iscsi_set_param() The validity of sock should be checked before assignment to avoid incorrect values. Commit 57569c37f0ad ("scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername()") introduced this change which may lead to inconsistent values of tcp_sw_conn->sendpage and conn->datadgst_en. Fix the issue by moving the position of the assignment.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Fix steering rules cleanup vport's mc, uc and multicast rules are not deleted in teardown path when EEH happens. Since the vport's promisc settings(uc, mc and all) in firmware are reset after EEH, mlx5 driver will try to delete the above rules in the initialization path. This cause kernel crash because these software rules are no longer valid. Fix by nullifying these rules right after delete to avoid accessing any dangling pointers. Call Trace: __list_del_entry_valid+0xcc/0x100 (unreliable) tree_put_node+0xf4/0x1b0 [mlx5_core] tree_remove_node+0x30/0x70 [mlx5_core] mlx5_del_flow_rules+0x14c/0x1f0 [mlx5_core] esw_apply_vport_rx_mode+0x10c/0x200 [mlx5_core] esw_update_vport_rx_mode+0xb4/0x180 [mlx5_core] esw_vport_change_handle_locked+0x1ec/0x230 [mlx5_core] esw_enable_vport+0x130/0x260 [mlx5_core] mlx5_eswitch_enable_sriov+0x2a0/0x2f0 [mlx5_core] mlx5_device_enable_sriov+0x74/0x440 [mlx5_core] mlx5_load_one+0x114c/0x1550 [mlx5_core] mlx5_pci_resume+0x68/0xf0 [mlx5_core] eeh_report_resume+0x1a4/0x230 eeh_pe_dev_traverse+0x98/0x170 eeh_handle_normal_event+0x3e4/0x640 eeh_handle_event+0x4c/0x370 eeh_event_handler+0x14c/0x210 kthread+0x168/0x1b0 ret_from_kernel_thread+0x5c/0x84

In the Linux kernel, the following vulnerability has been resolved: FS: JFS: Fix null-ptr-deref Read in txBegin Syzkaller reported an issue where txBegin may be called on a superblock in a read-only mounted filesystem which leads to NULL pointer deref. This could be solved by checking if the filesystem is read-only before calling txBegin, and returning with appropiate error code.

In the Linux kernel, the following vulnerability has been resolved: RDMA/cxgb4: Fix potential null-ptr-deref in pass_establish() If get_ep_from_tid() fails to lookup non-NULL value for ep, ep is dereferenced later regardless of whether it is empty. This patch adds a simple sanity check to fix the issue. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: ice: Don't tx before switchdev is fully configured There is possibility that ice_eswitch_port_start_xmit might be called while some resources are still not allocated which might cause NULL pointer dereference. Fix this by checking if switchdev configuration was finished.

In the Linux kernel, the following vulnerability has been resolved: HID: betop: check shape of output reports betopff_init() only checks the total sum of the report counts for each report field to be at least 4, but hid_betopff_play() expects 4 report fields. A device advertising an output report with one field and 4 report counts would pass the check but crash the kernel with a NULL pointer dereference in hid_betopff_play().

In the Linux kernel, the following vulnerability has been resolved: genirq/ipi: Fix NULL pointer deref in irq_data_get_affinity_mask() If ipi_send_{mask|single}() is called with an invalid interrupt number, all the local variables there will be NULL. ipi_send_verify() which is invoked from these functions does verify its 'data' parameter, resulting in a kernel oops in irq_data_get_affinity_mask() as the passed NULL pointer gets dereferenced. Add a missing NULL pointer check in ipi_send_verify()... Found by Linux Verification Center (linuxtesting.org) with the SVACE static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: media: rc: gpio-ir-recv: add remove function In case runtime PM is enabled, do runtime PM clean up to remove cpu latency qos request, otherwise driver removal may have below kernel dump: [ 19.463299] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000048 [ 19.472161] Mem abort info: [ 19.474985] ESR = 0x0000000096000004 [ 19.478754] EC = 0x25: DABT (current EL), IL = 32 bits [ 19.484081] SET = 0, FnV = 0 [ 19.487149] EA = 0, S1PTW = 0 [ 19.490361] FSC = 0x04: level 0 translation fault [ 19.495256] Data abort info: [ 19.498149] ISV = 0, ISS = 0x00000004 [ 19.501997] CM = 0, WnR = 0 [ 19.504977] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000049f81000 [ 19.511432] [0000000000000048] pgd=0000000000000000, p4d=0000000000000000 [ 19.518245] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP [ 19.524520] Modules linked in: gpio_ir_recv(+) rc_core [last unloaded: rc_core] [ 19.531845] CPU: 0 PID: 445 Comm: insmod Not tainted 6.2.0-rc1-00028-g2c397a46d47c #72 [ 19.531854] Hardware name: FSL i.MX8MM EVK board (DT) [ 19.531859] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 19.551777] pc : cpu_latency_qos_remove_request+0x20/0x110 [ 19.557277] lr : gpio_ir_recv_runtime_suspend+0x18/0x30 [gpio_ir_recv] [ 19.557294] sp : ffff800008ce3740 [ 19.557297] x29: ffff800008ce3740 x28: 0000000000000000 x27: ffff800008ce3d50 [ 19.574270] x26: ffffc7e3e9cea100 x25: 00000000000f4240 x24: ffffc7e3f9ef0e30 [ 19.574284] x23: 0000000000000000 x22: ffff0061803820f4 x21: 0000000000000008 [ 19.574296] x20: ffffc7e3fa75df30 x19: 0000000000000020 x18: ffffffffffffffff [ 19.588570] x17: 0000000000000000 x16: ffffc7e3f9efab70 x15: ffffffffffffffff [ 19.595712] x14: ffff800008ce37b8 x13: ffff800008ce37aa x12: 0000000000000001 [ 19.602853] x11: 0000000000000001 x10: ffffcbe3ec0dff87 x9 : 0000000000000008 [ 19.609991] x8 : 0101010101010101 x7 : 0000000000000000 x6 : 000000000f0bfe9f [ 19.624261] x5 : 00ffffffffffffff x4 : 0025ab8e00000000 x3 : ffff006180382010 [ 19.631405] x2 : ffffc7e3e9ce8030 x1 : ffffc7e3fc3eb810 x0 : 0000000000000020 [ 19.638548] Call trace: [ 19.640995] cpu_latency_qos_remove_request+0x20/0x110 [ 19.646142] gpio_ir_recv_runtime_suspend+0x18/0x30 [gpio_ir_recv] [ 19.652339] pm_generic_runtime_suspend+0x2c/0x44 [ 19.657055] __rpm_callback+0x48/0x1dc [ 19.660807] rpm_callback+0x6c/0x80 [ 19.664301] rpm_suspend+0x10c/0x640 [ 19.667880] rpm_idle+0x250/0x2d0 [ 19.671198] update_autosuspend+0x38/0xe0 [ 19.675213] pm_runtime_set_autosuspend_delay+0x40/0x60 [ 19.680442] gpio_ir_recv_probe+0x1b4/0x21c [gpio_ir_recv] [ 19.685941] platform_probe+0x68/0xc0 [ 19.689610] really_probe+0xc0/0x3dc [ 19.693189] __driver_probe_device+0x7c/0x190 [ 19.697550] driver_probe_device+0x3c/0x110 [ 19.701739] __driver_attach+0xf4/0x200 [ 19.705578] bus_for_each_dev+0x70/0xd0 [ 19.709417] driver_attach+0x24/0x30 [ 19.712998] bus_add_driver+0x17c/0x240 [ 19.716834] driver_register+0x78/0x130 [ 19.720676] __platform_driver_register+0x28/0x34 [ 19.725386] gpio_ir_recv_driver_init+0x20/0x1000 [gpio_ir_recv] [ 19.731404] do_one_initcall+0x44/0x2ac [ 19.735243] do_init_module+0x48/0x1d0 [ 19.739003] load_module+0x19fc/0x2034 [ 19.742759] __do_sys_finit_module+0xac/0x12c [ 19.747124] __arm64_sys_finit_module+0x20/0x30 [ 19.751664] invoke_syscall+0x48/0x114 [ 19.755420] el0_svc_common.constprop.0+0xcc/0xec [ 19.760132] do_el0_svc+0x38/0xb0 [ 19.763456] el0_svc+0x2c/0x84 [ 19.766516] el0t_64_sync_handler+0xf4/0x120 [ 19.770789] el0t_64_sync+0x190/0x194 [ 19.774460] Code: 910003fd a90153f3 aa0003f3 91204021 (f9401400) [ 19.780556] ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: pstore/platform: Add check for kstrdup Add check for the return value of kstrdup() and return the error if it fails in order to avoid NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: bcache: Fix __bch_btree_node_alloc to make the failure behavior consistent In some specific situations, the return value of __bch_btree_node_alloc may be NULL. This may lead to a potential NULL pointer dereference in caller function like a calling chain : btree_split->bch_btree_node_alloc->__bch_btree_node_alloc. Fix it by initializing the return value in __bch_btree_node_alloc.

In the Linux kernel, the following vulnerability has been resolved: media: vidtv: mux: Add check and kfree for kstrdup Add check for the return value of kstrdup() and return the error if it fails in order to avoid NULL pointer dereference. Moreover, use kfree() in the later error handling in order to avoid memory leak.

In the Linux kernel, the following vulnerability has been resolved: media: amphion: fix REVERSE_INULL issues reported by coverity null-checking of a pointor is suggested before dereferencing it

In the Linux kernel, the following vulnerability has been resolved: net: wwan: iosm: fix NULL pointer dereference when removing device In suspend and resume cycle, the removal and rescan of device ends up in NULL pointer dereference. During driver initialization, if the ipc_imem_wwan_channel_init() fails to get the valid device capabilities it returns an error and further no resource (wwan struct) will be allocated. Now in this situation if driver removal procedure is initiated it would result in NULL pointer exception since unallocated wwan struct is dereferenced inside ipc_wwan_deinit(). ipc_imem_run_state_worker() to handle the called functions return value and to release the resource in failure case. It also reports the link down event in failure cases. The user space application can handle this event to do a device reset for restoring the device communication.

In the Linux kernel, the following vulnerability has been resolved: drm/ttm: Fix a NULL pointer dereference The LRU mechanism may look up a resource in the process of being removed from an object. The locking rules here are a bit unclear but it looks currently like res->bo assignment is protected by the LRU lock, whereas bo->resource is protected by the object lock, while *clearing* of bo->resource is also protected by the LRU lock. This means that if we check that bo->resource points to the LRU resource under the LRU lock we should be safe. So perform that check before deciding to swap out a bo. That avoids dereferencing a NULL bo->resource in ttm_bo_swapout().

In the Linux kernel, the following vulnerability has been resolved: iw_cxgb4: Fix potential NULL dereference in c4iw_fill_res_cm_id_entry() This condition needs to match the previous "if (epcp->state == LISTEN) {" exactly to avoid a NULL dereference of either "listen_ep" or "ep". The problem is that "epcp" has been re-assigned so just testing "if (epcp->state == LISTEN) {" a second time is not sufficient.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix cleanup null-ptr deref on encap lock During module is unloaded while a peer tc flow is still offloaded, first the peer uplink rep profile is changed to a nic profile, and so neigh encap lock is destroyed. Next during unload, the VF reps netdevs are unregistered which causes the original non-peer tc flow to be deleted, which deletes the peer flow. The peer flow deletion detaches the encap entry and try to take the already destroyed encap lock, causing the below trace. Fix this by clearing peer flows during tc eswitch cleanup (mlx5e_tc_esw_cleanup()). Relevant trace: [ 4316.837128] BUG: kernel NULL pointer dereference, address: 00000000000001d8 [ 4316.842239] RIP: 0010:__mutex_lock+0xb5/0xc40 [ 4316.851897] Call Trace: [ 4316.852481] <TASK> [ 4316.857214] mlx5e_rep_neigh_entry_release+0x93/0x790 [mlx5_core] [ 4316.858258] mlx5e_rep_encap_entry_detach+0xa7/0xf0 [mlx5_core] [ 4316.859134] mlx5e_encap_dealloc+0xa3/0xf0 [mlx5_core] [ 4316.859867] clean_encap_dests.part.0+0x5c/0xe0 [mlx5_core] [ 4316.860605] mlx5e_tc_del_fdb_flow+0x32a/0x810 [mlx5_core] [ 4316.862609] __mlx5e_tc_del_fdb_peer_flow+0x1a2/0x250 [mlx5_core] [ 4316.863394] mlx5e_tc_del_flow+0x(/0x630 [mlx5_core] [ 4316.864090] mlx5e_flow_put+0x5f/0x100 [mlx5_core] [ 4316.864771] mlx5e_delete_flower+0x4de/0xa40 [mlx5_core] [ 4316.865486] tc_setup_cb_reoffload+0x20/0x80 [ 4316.865905] fl_reoffload+0x47c/0x510 [cls_flower] [ 4316.869181] tcf_block_playback_offloads+0x91/0x1d0 [ 4316.869649] tcf_block_unbind+0xe7/0x1b0 [ 4316.870049] tcf_block_offload_cmd.isra.0+0x1ee/0x270 [ 4316.879266] tcf_block_offload_unbind+0x61/0xa0 [ 4316.879711] __tcf_block_put+0xa4/0x310

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: coex: check NULL return of kmalloc in btc_fw_set_monreg() kmalloc may fail, return value might be NULL and will cause NULL pointer dereference. Add check NULL return of kmalloc in btc_fw_set_monreg().

In the Linux kernel, the following vulnerability has been resolved: vfio/mdev: Fix a null-ptr-deref bug for mdev_unregister_parent() Inject fault while probing mdpy.ko, if kstrdup() of create_dir() fails in kobject_add_internal() in kobject_init_and_add() in mdev_type_add() in parent_create_sysfs_files(), it will return 0 and probe successfully. And when rmmod mdpy.ko, the mdpy_dev_exit() will call mdev_unregister_parent(), the mdev_type_remove() may traverse uninitialized parent->types[i] in parent_remove_sysfs_files(), and it will cause below null-ptr-deref. If mdev_type_add() fails, return the error code and kset_unregister() to fix the issue. general protection fault, probably for non-canonical address 0xdffffc0000000002: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017] CPU: 2 PID: 10215 Comm: rmmod Tainted: G W N 6.6.0-rc2+ #20 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:__kobject_del+0x62/0x1c0 Code: 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 51 01 00 00 48 b8 00 00 00 00 00 fc ff df 48 8b 6b 28 48 8d 7d 10 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 24 01 00 00 48 8b 75 10 48 89 df 48 8d 6b 3c e8 RSP: 0018:ffff88810695fd30 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: ffffffffa0270268 RCX: 0000000000000000 RDX: 0000000000000002 RSI: 0000000000000004 RDI: 0000000000000010 RBP: 0000000000000000 R08: 0000000000000001 R09: ffffed10233a4ef1 R10: ffff888119d2778b R11: 0000000063666572 R12: 0000000000000000 R13: fffffbfff404e2d4 R14: dffffc0000000000 R15: ffffffffa0271660 FS: 00007fbc81981540(0000) GS:ffff888119d00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc14a142dc0 CR3: 0000000110a62003 CR4: 0000000000770ee0 DR0: ffffffff8fb0bce8 DR1: ffffffff8fb0bce9 DR2: ffffffff8fb0bcea DR3: ffffffff8fb0bceb DR6: 00000000fffe0ff0 DR7: 0000000000000600 PKRU: 55555554 Call Trace: <TASK> ? die_addr+0x3d/0xa0 ? exc_general_protection+0x144/0x220 ? asm_exc_general_protection+0x22/0x30 ? __kobject_del+0x62/0x1c0 kobject_del+0x32/0x50 parent_remove_sysfs_files+0xd6/0x170 [mdev] mdev_unregister_parent+0xfb/0x190 [mdev] ? mdev_register_parent+0x270/0x270 [mdev] ? find_module_all+0x9d/0xe0 mdpy_dev_exit+0x17/0x63 [mdpy] __do_sys_delete_module.constprop.0+0x2fa/0x4b0 ? module_flags+0x300/0x300 ? __fput+0x4e7/0xa00 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x46/0xb0 RIP: 0033:0x7fbc813221b7 Code: 73 01 c3 48 8b 0d d1 8c 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d a1 8c 2c 00 f7 d8 64 89 01 48 RSP: 002b:00007ffe780e0648 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0 RAX: ffffffffffffffda RBX: 00007ffe780e06a8 RCX: 00007fbc813221b7 RDX: 000000000000000a RSI: 0000000000000800 RDI: 000055e214df9b58 RBP: 000055e214df9af0 R08: 00007ffe780df5c1 R09: 0000000000000000 R10: 00007fbc8139ecc0 R11: 0000000000000206 R12: 00007ffe780e0870 R13: 00007ffe780e0ed0 R14: 000055e214df9260 R15: 000055e214df9af0 </TASK> Modules linked in: mdpy(-) mdev vfio_iommu_type1 vfio [last unloaded: mdpy] Dumping ftrace buffer: (ftrace buffer empty) ---[ end trace 0000000000000000 ]--- RIP: 0010:__kobject_del+0x62/0x1c0 Code: 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 51 01 00 00 48 b8 00 00 00 00 00 fc ff df 48 8b 6b 28 48 8d 7d 10 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 24 01 00 00 48 8b 75 10 48 89 df 48 8d 6b 3c e8 RSP: 0018:ffff88810695fd30 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: ffffffffa0270268 RCX: 0000000000000000 RDX: 0000000000000002 RSI: 0000000000000004 RDI: 0000000000000010 RBP: 0000000000000000 R08: 0000000000000001 R09: ffffed10233a4ef1 R10: ffff888119d2778b R11: 0000000063666572 R12: 0000000000000000 R13: fffffbfff404e2d4 R14: dffffc0000000000 R15: ffffffffa0271660 FS: 00007fbc81981540(0000) GS:ffff888119d00000(000 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Fix an NULL dereference bug The issue here is when this is called from ntfs_load_attr_list(). The "size" comes from le32_to_cpu(attr->res.data_size) so it can't overflow on a 64bit systems but on 32bit systems the "+ 1023" can overflow and the result is zero. This means that the kmalloc will succeed by returning the ZERO_SIZE_PTR and then the memcpy() will crash with an Oops on the next line.

In the Linux kernel, the following vulnerability has been resolved: RDMA/irdma: Fix potential NULL-ptr-dereference in_dev_get() can return NULL which will cause a failure once idev is dereferenced in in_dev_for_each_ifa_rtnl(). This patch adds a check for NULL value in idev beforehand. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: mfd: syscon: Fix null pointer dereference in of_syscon_register() kasprintf() returns a pointer to dynamically allocated memory which can be NULL upon failure.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/vkms: fix a possible null pointer dereference In amdgpu_vkms_conn_get_modes(), the return value of drm_cvt_mode() is assigned to mode, which will lead to a NULL pointer dereference on failure of drm_cvt_mode(). Add a check to avoid null pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: spi: spi-zynq-qspi: Fix a NULL pointer dereference in zynq_qspi_exec_mem_op() In zynq_qspi_exec_mem_op(), kzalloc() is directly used in memset(), which could lead to a NULL pointer dereference on failure of kzalloc(). Fix this bug by adding a check of tmpbuf. This bug was found by a static analyzer. The analysis employs differential checking to identify inconsistent security operations (e.g., checks or kfrees) between two code paths and confirms that the inconsistent operations are not recovered in the current function or the callers, so they constitute bugs. Note that, as a bug found by static analysis, it can be a false positive or hard to trigger. Multiple researchers have cross-reviewed the bug. Builds with CONFIG_SPI_ZYNQ_QSPI=m show no new warnings, and our static analyzer no longer warns about this code.

In the Linux kernel, the following vulnerability has been resolved: nvmet-tcp: Fix a kernel panic when host sends an invalid H2C PDU length If the host sends an H2CData command with an invalid DATAL, the kernel may crash in nvmet_tcp_build_pdu_iovec(). Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 lr : nvmet_tcp_io_work+0x6ac/0x718 [nvmet_tcp] Call trace: process_one_work+0x174/0x3c8 worker_thread+0x2d0/0x3e8 kthread+0x104/0x110 Fix the bug by raising a fatal error if DATAL isn't coherent with the packet size. Also, the PDU length should never exceed the MAXH2CDATA parameter which has been communicated to the host in nvmet_tcp_handle_icreq().

In the Linux kernel, the following vulnerability has been resolved: net: wangxun: fix kernel panic due to null pointer When the device uses a custom subsystem vendor ID, the function wx_sw_init() returns before the memory of 'wx->mac_table' is allocated. The null pointer will causes the kernel panic.

In the Linux kernel, the following vulnerability has been resolved: udmabuf: change folios array from kmalloc to kvmalloc When PAGE_SIZE 4096, MAX_PAGE_ORDER 10, 64bit machine, page_alloc only support 4MB. If above this, trigger this warn and return NULL. udmabuf can change size limit, if change it to 3072(3GB), and then alloc 3GB udmabuf, will fail create. [ 4080.876581] ------------[ cut here ]------------ [ 4080.876843] WARNING: CPU: 3 PID: 2015 at mm/page_alloc.c:4556 __alloc_pages+0x2c8/0x350 [ 4080.878839] RIP: 0010:__alloc_pages+0x2c8/0x350 [ 4080.879470] Call Trace: [ 4080.879473] <TASK> [ 4080.879473] ? __alloc_pages+0x2c8/0x350 [ 4080.879475] ? __warn.cold+0x8e/0xe8 [ 4080.880647] ? __alloc_pages+0x2c8/0x350 [ 4080.880909] ? report_bug+0xff/0x140 [ 4080.881175] ? handle_bug+0x3c/0x80 [ 4080.881556] ? exc_invalid_op+0x17/0x70 [ 4080.881559] ? asm_exc_invalid_op+0x1a/0x20 [ 4080.882077] ? udmabuf_create+0x131/0x400 Because MAX_PAGE_ORDER, kmalloc can max alloc 4096 * (1 << 10), 4MB memory, each array entry is pointer(8byte), so can save 524288 pages(2GB). Further more, costly order(order 3) may not be guaranteed that it can be applied for, due to fragmentation. This patch change udmabuf array use kvmalloc_array, this can fallback alloc into vmalloc, which can guarantee allocation for any size and does not affect the performance of kmalloc allocations.

In the Linux kernel, the following vulnerability has been resolved: IB/IPoIB: Fix legacy IPoIB due to wrong number of queues The cited commit creates child PKEY interfaces over netlink will multiple tx and rx queues, but some devices doesn't support more than 1 tx and 1 rx queues. This causes to a crash when traffic is sent over the PKEY interface due to the parent having a single queue but the child having multiple queues. This patch fixes the number of queues to 1 for legacy IPoIB at the earliest possible point in time. BUG: kernel NULL pointer dereference, address: 000000000000036b PGD 0 P4D 0 Oops: 0000 [#1] SMP CPU: 4 PID: 209665 Comm: python3 Not tainted 6.1.0_for_upstream_min_debug_2022_12_12_17_02 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:kmem_cache_alloc+0xcb/0x450 Code: ce 7e 49 8b 50 08 49 83 78 10 00 4d 8b 28 0f 84 cb 02 00 00 4d 85 ed 0f 84 c2 02 00 00 41 8b 44 24 28 48 8d 4a 01 49 8b 3c 24 <49> 8b 5c 05 00 4c 89 e8 65 48 0f c7 0f 0f 94 c0 84 c0 74 b8 41 8b RSP: 0018:ffff88822acbbab8 EFLAGS: 00010202 RAX: 0000000000000070 RBX: ffff8881c28e3e00 RCX: 00000000064f8dae RDX: 00000000064f8dad RSI: 0000000000000a20 RDI: 0000000000030d00 RBP: 0000000000000a20 R08: ffff8882f5d30d00 R09: ffff888104032f40 R10: ffff88810fade828 R11: 736f6d6570736575 R12: ffff88810081c000 R13: 00000000000002fb R14: ffffffff817fc865 R15: 0000000000000000 FS: 00007f9324ff9700(0000) GS:ffff8882f5d00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000000036b CR3: 00000001125af004 CR4: 0000000000370ea0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> skb_clone+0x55/0xd0 ip6_finish_output2+0x3fe/0x690 ip6_finish_output+0xfa/0x310 ip6_send_skb+0x1e/0x60 udp_v6_send_skb+0x1e5/0x420 udpv6_sendmsg+0xb3c/0xe60 ? ip_mc_finish_output+0x180/0x180 ? __switch_to_asm+0x3a/0x60 ? __switch_to_asm+0x34/0x60 sock_sendmsg+0x33/0x40 __sys_sendto+0x103/0x160 ? _copy_to_user+0x21/0x30 ? kvm_clock_get_cycles+0xd/0x10 ? ktime_get_ts64+0x49/0xe0 __x64_sys_sendto+0x25/0x30 do_syscall_64+0x3d/0x90 entry_SYSCALL_64_after_hwframe+0x46/0xb0 RIP: 0033:0x7f9374f1ed14 Code: 42 41 f8 ff 44 8b 4c 24 2c 4c 8b 44 24 20 89 c5 44 8b 54 24 28 48 8b 54 24 18 b8 2c 00 00 00 48 8b 74 24 10 8b 7c 24 08 0f 05 <48> 3d 00 f0 ff ff 77 34 89 ef 48 89 44 24 08 e8 68 41 f8 ff 48 8b RSP: 002b:00007f9324ff7bd0 EFLAGS: 00000293 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00007f9324ff7cc8 RCX: 00007f9374f1ed14 RDX: 00000000000002fb RSI: 00007f93000052f0 RDI: 0000000000000030 RBP: 0000000000000000 R08: 00007f9324ff7d40 R09: 000000000000001c R10: 0000000000000000 R11: 0000000000000293 R12: 0000000000000000 R13: 000000012a05f200 R14: 0000000000000001 R15: 00007f9374d57bdc </TASK>

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix possible NULL dereference in amdgpu_ras_query_error_status_helper() Return invalid error code -EINVAL for invalid block id. Fixes the below: drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:1183 amdgpu_ras_query_error_status_helper() error: we previously assumed 'info' could be null (see line 1176)

In the Linux kernel, the following vulnerability has been resolved: serial: 8250_port: Check IRQ data before use In case the leaf driver wants to use IRQ polling (irq = 0) and IIR register shows that an interrupt happened in the 8250 hardware the IRQ data can be NULL. In such a case we need to skip the wake event as we came to this path from the timer interrupt and quite likely system is already awake. Without this fix we have got an Oops: serial8250: ttyS0 at I/O 0x3f8 (irq = 0, base_baud = 115200) is a 16550A ... BUG: kernel NULL pointer dereference, address: 0000000000000010 RIP: 0010:serial8250_handle_irq+0x7c/0x240 Call Trace: ? serial8250_handle_irq+0x7c/0x240 ? __pfx_serial8250_timeout+0x10/0x10

In the Linux kernel, the following vulnerability has been resolved: tls: fix NULL deref on tls_sw_splice_eof() with empty record syzkaller discovered that if tls_sw_splice_eof() is executed as part of sendfile() when the plaintext/ciphertext sk_msg are empty, the send path gets confused because the empty ciphertext buffer does not have enough space for the encryption overhead. This causes tls_push_record() to go on the `split = true` path (which is only supposed to be used when interacting with an attached BPF program), and then get further confused and hit the tls_merge_open_record() path, which then assumes that there must be at least one populated buffer element, leading to a NULL deref. It is possible to have empty plaintext/ciphertext buffers if we previously bailed from tls_sw_sendmsg_locked() via the tls_trim_both_msgs() path. tls_sw_push_pending_record() already handles this case correctly; let's do the same check in tls_sw_splice_eof().

In the Linux kernel, the following vulnerability has been resolved: drm/radeon: check the alloc_workqueue return value in radeon_crtc_init() check the alloc_workqueue return value in radeon_crtc_init() to avoid null-ptr-deref.