In the Linux kernel, the following vulnerability has been resolved: ice: Fix DMA mappings leak Fix leak, when user changes ring parameters. During reallocation of RX buffers, new DMA mappings are created for those buffers. New buffers with different RX ring count should substitute older ones, but those buffers were freed in ice_vsi_cfg_rxq and reallocated again with ice_alloc_rx_buf. kfree on rx_buf caused leak of already mapped DMA. Reallocate ZC with xdp_buf struct, when BPF program loads. Reallocate back to rx_buf, when BPF program unloads. If BPF program is loaded/unloaded and XSK pools are created, reallocate RX queues accordingly in XDP_SETUP_XSK_POOL handler. Steps for reproduction: while : do for ((i=0; i<=8160; i=i+32)) do ethtool -G enp130s0f0 rx $i tx $i sleep 0.5 ethtool -g enp130s0f0 done done

In the Linux kernel, the following vulnerability has been resolved: can: can327: can327_feed_frame_to_netdev(): fix potential skb leak when netdev is down In can327_feed_frame_to_netdev(), it did not free the skb when netdev is down, and all callers of can327_feed_frame_to_netdev() did not free allocated skb too. That would trigger skb leak. Fix it by adding kfree_skb() in can327_feed_frame_to_netdev() when netdev is down. Not tested, just compiled.

In the Linux kernel, the following vulnerability has been resolved: ixgbe: fix pci device refcount leak As the comment of pci_get_domain_bus_and_slot() says, it returns a PCI device with refcount incremented, when finish using it, the caller must decrement the reference count by calling pci_dev_put(). In ixgbe_get_first_secondary_devfn() and ixgbe_x550em_a_has_mii(), pci_dev_put() is called to avoid leak.

In the Linux kernel, the following vulnerability has been resolved: bpf, sockmap: Fix memleak in tcp_bpf_sendmsg while sk msg is full If tcp_bpf_sendmsg() is running while sk msg is full. When sk_msg_alloc() returns -ENOMEM error, tcp_bpf_sendmsg() goes to wait_for_memory. If partial memory has been alloced by sk_msg_alloc(), that is, msg_tx->sg.size is greater than osize after sk_msg_alloc(), memleak occurs. To fix we use sk_msg_trim() to release the allocated memory, then goto wait for memory. Other call paths of sk_msg_alloc() have the similar issue, such as tls_sw_sendmsg(), so handle sk_msg_trim logic inside sk_msg_alloc(), as Cong Wang suggested. This issue can cause the following info: WARNING: CPU: 3 PID: 7950 at net/core/stream.c:208 sk_stream_kill_queues+0xd4/0x1a0 Call Trace: <TASK> inet_csk_destroy_sock+0x55/0x110 __tcp_close+0x279/0x470 tcp_close+0x1f/0x60 inet_release+0x3f/0x80 __sock_release+0x3d/0xb0 sock_close+0x11/0x20 __fput+0x92/0x250 task_work_run+0x6a/0xa0 do_exit+0x33b/0xb60 do_group_exit+0x2f/0xa0 get_signal+0xb6/0x950 arch_do_signal_or_restart+0xac/0x2a0 exit_to_user_mode_prepare+0xa9/0x200 syscall_exit_to_user_mode+0x12/0x30 do_syscall_64+0x46/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae </TASK> WARNING: CPU: 3 PID: 2094 at net/ipv4/af_inet.c:155 inet_sock_destruct+0x13c/0x260 Call Trace: <TASK> __sk_destruct+0x24/0x1f0 sk_psock_destroy+0x19b/0x1c0 process_one_work+0x1b3/0x3c0 kthread+0xe6/0x110 ret_from_fork+0x22/0x30 </TASK>

In the Linux kernel, the following vulnerability has been resolved: ice: Fix potential memory leak in ice_gnss_tty_write() The ice_gnss_tty_write() return directly if the write_buf alloc failed, leaking the cmd_buf. Fix by free cmd_buf if write_buf alloc failed.

In the Linux kernel, the following vulnerability has been resolved: PCI: endpoint: Fix misused goto label Fix a misused goto label jump since that can result in a memory leak.

In the Linux kernel, the following vulnerability has been resolved: net: mdiobus: fix unbalanced node reference count I got the following report while doing device(mscc-miim) load test with CONFIG_OF_UNITTEST and CONFIG_OF_DYNAMIC enabled: OF: ERROR: memory leak, expected refcount 1 instead of 2, of_node_get()/of_node_put() unbalanced - destroy cset entry: attach overlay node /spi/soc@0/mdio@7107009c/ethernet-phy@0 If the 'fwnode' is not an acpi node, the refcount is get in fwnode_mdiobus_phy_device_register(), but it has never been put when the device is freed in the normal path. So call fwnode_handle_put() in phy_device_release() to avoid leak. If it's an acpi node, it has never been get, but it's put in the error path, so call fwnode_handle_get() before phy_device_register() to keep get/put operation balanced.

In the Linux kernel, the following vulnerability has been resolved: net: thunderbolt: fix memory leak in tbnet_open() When tb_ring_alloc_rx() failed in tbnet_open(), ida that allocated in tb_xdomain_alloc_out_hopid() is not released. Add tb_xdomain_release_out_hopid() to the error path to release ida.

In the Linux kernel, the following vulnerability has been resolved: net: ieee802154: at86rf230: Stop leaking skb's Upon error the ieee802154_xmit_complete() helper is not called. Only ieee802154_wake_queue() is called manually. In the Tx case we then leak the skb structure. Free the skb structure upon error before returning when appropriate. As the 'is_tx = 0' cannot be moved in the complete handler because of a possible race between the delay in switching to STATE_RX_AACK_ON and a new interrupt, we introduce an intermediate 'was_tx' boolean just for this purpose. There is no Fixes tag applying here, many changes have been made on this area and the issue kind of always existed.

In the Linux kernel, the following vulnerability has been resolved: nfs: fix acl memory leak of posix_acl_create() When looking into another nfs xfstests report, I found acl and default_acl in nfs3_proc_create() and nfs3_proc_mknod() error paths are possibly leaked. Fix them in advance.

In the Linux kernel, the following vulnerability has been resolved: dmaengine: ti: k3-udma-private: Fix refcount leak bug in of_xudma_dev_get() We should call of_node_put() for the reference returned by of_parse_phandle() in fail path or when it is not used anymore. Here we only need to move the of_node_put() before the check.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: fix percpu memory leak at nf_tables_addchain() It seems to me that percpu memory for chain stats started leaking since commit 3bc158f8d0330f0a ("netfilter: nf_tables: map basechain priority to hardware priority") when nft_chain_offload_priority() returned an error.

In the Linux kernel, the following vulnerability has been resolved: clk: mediatek: Fix memory leaks on probe Handle the error branches to free memory where required. Addresses-Coverity-ID: 1491825 ("Resource leak")

In the Linux kernel, the following vulnerability has been resolved: dpaa2-switch: Fix memory leak in dpaa2_switch_acl_entry_add() and dpaa2_switch_acl_entry_remove() The cmd_buff needs to be freed when error happened in dpaa2_switch_acl_entry_add() and dpaa2_switch_acl_entry_remove().

In the Linux kernel, the following vulnerability has been resolved: ethernet: Fix error handling in xemaclite_of_probe This node pointer is returned by of_parse_phandle() with refcount incremented in this function. Calling of_node_put() to avoid the refcount leak. As the remove function do.

In the Linux kernel, the following vulnerability has been resolved: mm/mempolicy: fix mpol_new leak in shared_policy_replace If mpol_new is allocated but not used in restart loop, mpol_new will be freed via mpol_put before returning to the caller. But refcnt is not initialized yet, so mpol_put could not do the right things and might leak the unused mpol_new. This would happen if mempolicy was updated on the shared shmem file while the sp->lock has been dropped during the memory allocation. This issue could be triggered easily with the below code snippet if there are many processes doing the below work at the same time: shmid = shmget((key_t)5566, 1024 * PAGE_SIZE, 0666|IPC_CREAT); shm = shmat(shmid, 0, 0); loop many times { mbind(shm, 1024 * PAGE_SIZE, MPOL_LOCAL, mask, maxnode, 0); mbind(shm + 128 * PAGE_SIZE, 128 * PAGE_SIZE, MPOL_DEFAULT, mask, maxnode, 0); }

In the Linux kernel, the following vulnerability has been resolved: scsi: pm8001: Fix memory leak in pm8001_chip_fw_flash_update_req() In pm8001_chip_fw_flash_update_build(), if pm8001_chip_fw_flash_update_build() fails, the struct fw_control_ex allocated must be freed.

In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Fix memory leak in error flow for subscribe event routine In case the second xa_insert() fails, the obj_event is not released. Fix the error unwind flow to free that memory to avoid a memory leak.

In the Linux kernel, the following vulnerability has been resolved: netfilter: ebtables: fix memory leak when blob is malformed The bug fix was incomplete, it "replaced" crash with a memory leak. The old code had an assignment to "ret" embedded into the conditional, restore this.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: fix memory leak during stateful obj update stateful objects can be updated from the control plane. The transaction logic allocates a temporary object for this purpose. The ->init function was called for this object, so plain kfree() leaks resources. We must call ->destroy function of the object. nft_obj_destroy does this, but it also decrements the module refcount, but the update path doesn't increment it. To avoid special-casing the update object release, do module_get for the update case too and release it via nft_obj_destroy().

In the Linux kernel, the following vulnerability has been resolved: mxser: fix xmit_buf leak in activate when LSR == 0xff When LSR is 0xff in ->activate() (rather unlike), we return an error. Provided ->shutdown() is not called when ->activate() fails, nothing actually frees the buffer in this case. Fix this by properly freeing the buffer in a designated label. We jump there also from the "!info->type" if now too.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: use memset avoid memory leaks Use memset to initialize structs to prevent memory leaks in l2cap_ecred_connect

In the Linux kernel, the following vulnerability has been resolved: staging: wfx: fix an error handling in wfx_init_common() One error handler of wfx_init_common() return without calling ieee80211_free_hw(hw), which may result in memory leak. And I add one err label to unify the error handler, which is useful for the subsequent changes.

In the Linux kernel, the following vulnerability has been resolved: scsi: mpi3mr: Fix memory leaks Fix memory leaks related to operational reply queue's memory segments which are not getting freed while unloading the driver.

In the Linux kernel, the following vulnerability has been resolved: ice: switch: fix potential memleak in ice_add_adv_recipe() When ice_add_special_words() fails, the 'rm' is not released, which will lead to a memory leak. Fix this up by going to 'err_unroll' label. Compile tested only.

In the Linux kernel, the following vulnerability has been resolved: iommu/amd: Fix I/O page table memory leak The current logic updates the I/O page table mode for the domain before calling the logic to free memory used for the page table. This results in IOMMU page table memory leak, and can be observed when launching VM w/ pass-through devices. Fix by freeing the memory used for page table before updating the mode.

In the Linux kernel, the following vulnerability has been resolved: soc: brcmstb: pm-arm: Fix refcount leak and __iomem leak bugs In brcmstb_pm_probe(), there are two kinds of leak bugs: (1) we need to add of_node_put() when for_each__matching_node() breaks (2) we need to add iounmap() for each iomap in fail path

In the Linux kernel, the following vulnerability has been resolved: gianfar: ethtool: Fix refcount leak in gfar_get_ts_info The of_find_compatible_node() function returns a node pointer with refcount incremented, We should use of_node_put() on it when done Add the missing of_node_put() to release the refcount.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix memory leak [why] Resource release is needed on the error handling path to prevent memory leak. [how] Fix this by adding kfree on the error handling path.

In the Linux kernel, the following vulnerability has been resolved: net/9p: Fix a potential socket leak in p9_socket_open Both p9_fd_create_tcp() and p9_fd_create_unix() will call p9_socket_open(). If the creation of p9_trans_fd fails, p9_fd_create_tcp() and p9_fd_create_unix() will return an error directly instead of releasing the cscoket, which will result in a socket leak. This patch adds sock_release() to fix the leak issue.

In the Linux kernel, the following vulnerability has been resolved: power: supply: ab8500: Fix memory leak in ab8500_fg_sysfs_init kobject_init_and_add() takes reference even when it fails. According to the doc of kobject_init_and_add()： If this function returns an error, kobject_put() must be called to properly clean up the memory associated with the object. Fix memory leak by calling kobject_put().

In the Linux kernel, the following vulnerability has been resolved: sctp: fix memory leak in sctp_stream_outq_migrate() When sctp_stream_outq_migrate() is called to release stream out resources, the memory pointed to by prio_head in stream out is not released. The memory leak information is as follows: unreferenced object 0xffff88801fe79f80 (size 64): comm "sctp_repo", pid 7957, jiffies 4294951704 (age 36.480s) hex dump (first 32 bytes): 80 9f e7 1f 80 88 ff ff 80 9f e7 1f 80 88 ff ff ................ 90 9f e7 1f 80 88 ff ff 90 9f e7 1f 80 88 ff ff ................ backtrace: [<ffffffff81b215c6>] kmalloc_trace+0x26/0x60 [<ffffffff88ae517c>] sctp_sched_prio_set+0x4cc/0x770 [<ffffffff88ad64f2>] sctp_stream_init_ext+0xd2/0x1b0 [<ffffffff88aa2604>] sctp_sendmsg_to_asoc+0x1614/0x1a30 [<ffffffff88ab7ff1>] sctp_sendmsg+0xda1/0x1ef0 [<ffffffff87f765ed>] inet_sendmsg+0x9d/0xe0 [<ffffffff8754b5b3>] sock_sendmsg+0xd3/0x120 [<ffffffff8755446a>] __sys_sendto+0x23a/0x340 [<ffffffff87554651>] __x64_sys_sendto+0xe1/0x1b0 [<ffffffff89978b49>] do_syscall_64+0x39/0xb0 [<ffffffff89a0008b>] entry_SYSCALL_64_after_hwframe+0x63/0xcd

In the Linux kernel, the following vulnerability has been resolved: RDMA/cma: Fix listener leak in rdma_cma_listen_on_all() failure If cma_listen_on_all() fails it leaves the per-device ID still on the listen_list but the state is not set to RDMA_CM_ADDR_BOUND. When the cmid is eventually destroyed cma_cancel_listens() is not called due to the wrong state, however the per-device IDs are still holding the refcount preventing the ID from being destroyed, thus deadlocking: task:rping state:D stack: 0 pid:19605 ppid: 47036 flags:0x00000084 Call Trace: __schedule+0x29a/0x780 ? free_unref_page_commit+0x9b/0x110 schedule+0x3c/0xa0 schedule_timeout+0x215/0x2b0 ? __flush_work+0x19e/0x1e0 wait_for_completion+0x8d/0xf0 _destroy_id+0x144/0x210 [rdma_cm] ucma_close_id+0x2b/0x40 [rdma_ucm] __destroy_id+0x93/0x2c0 [rdma_ucm] ? __xa_erase+0x4a/0xa0 ucma_destroy_id+0x9a/0x120 [rdma_ucm] ucma_write+0xb8/0x130 [rdma_ucm] vfs_write+0xb4/0x250 ksys_write+0xb5/0xd0 ? syscall_trace_enter.isra.19+0x123/0x190 do_syscall_64+0x33/0x40 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Ensure that cma_listen_on_all() atomically unwinds its action under the lock during error.

In the Linux kernel, the following vulnerability has been resolved: uio_hv_generic: Fix a memory leak in error handling paths If 'vmbus_establish_gpadl()' fails, the (recv|send)_gpadl will not be updated and 'hv_uio_cleanup()' in the error handling path will not be able to free the corresponding buffer. In such a case, we need to free the buffer explicitly.

In the Linux kernel, the following vulnerability has been resolved: firewire: ohci: prevent leak of left-over IRQ on unbind Commit 5a95f1ded28691e6 ("firewire: ohci: use devres for requested IRQ") also removed the call to free_irq() in pci_remove(), leading to a leftover irq of devm_request_irq() at pci_disable_msi() in pci_remove() when unbinding the driver from the device remove_proc_entry: removing non-empty directory 'irq/136', leaking at least 'firewire_ohci' Call Trace: ? remove_proc_entry+0x19c/0x1c0 ? __warn+0x81/0x130 ? remove_proc_entry+0x19c/0x1c0 ? report_bug+0x171/0x1a0 ? console_unlock+0x78/0x120 ? handle_bug+0x3c/0x80 ? exc_invalid_op+0x17/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? remove_proc_entry+0x19c/0x1c0 unregister_irq_proc+0xf4/0x120 free_desc+0x3d/0xe0 ? kfree+0x29f/0x2f0 irq_free_descs+0x47/0x70 msi_domain_free_locked.part.0+0x19d/0x1d0 msi_domain_free_irqs_all_locked+0x81/0xc0 pci_free_msi_irqs+0x12/0x40 pci_disable_msi+0x4c/0x60 pci_remove+0x9d/0xc0 [firewire_ohci 01b483699bebf9cb07a3d69df0aa2bee71db1b26] pci_device_remove+0x37/0xa0 device_release_driver_internal+0x19f/0x200 unbind_store+0xa1/0xb0 remove irq with devm_free_irq() before pci_disable_msi() also remove it in fail_msi: of pci_probe() as this would lead to an identical leak

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Mark target gfn of emulated atomic instruction as dirty When emulating an atomic access on behalf of the guest, mark the target gfn dirty if the CMPXCHG by KVM is attempted and doesn't fault. This fixes a bug where KVM effectively corrupts guest memory during live migration by writing to guest memory without informing userspace that the page is dirty. Marking the page dirty got unintentionally dropped when KVM's emulated CMPXCHG was converted to do a user access. Before that, KVM explicitly mapped the guest page into kernel memory, and marked the page dirty during the unmap phase. Mark the page dirty even if the CMPXCHG fails, as the old data is written back on failure, i.e. the page is still written. The value written is guaranteed to be the same because the operation is atomic, but KVM's ABI is that all writes are dirty logged regardless of the value written. And more importantly, that's what KVM did before the buggy commit. Huge kudos to the folks on the Cc list (and many others), who did all the actual work of triaging and debugging. base-commit: 6769ea8da8a93ed4630f1ce64df6aafcaabfce64

In the Linux kernel, the following vulnerability has been resolved: mm/kmemleak: avoid soft lockup in __kmemleak_do_cleanup() A soft lockup warning was observed on a relative small system x86-64 system with 16 GB of memory when running a debug kernel with kmemleak enabled. watchdog: BUG: soft lockup - CPU#8 stuck for 33s! [kworker/8:1:134] The test system was running a workload with hot unplug happening in parallel. Then kemleak decided to disable itself due to its inability to allocate more kmemleak objects. The debug kernel has its CONFIG_DEBUG_KMEMLEAK_MEM_POOL_SIZE set to 40,000. The soft lockup happened in kmemleak_do_cleanup() when the existing kmemleak objects were being removed and deleted one-by-one in a loop via a workqueue. In this particular case, there are at least 40,000 objects that need to be processed and given the slowness of a debug kernel and the fact that a raw_spinlock has to be acquired and released in __delete_object(), it could take a while to properly handle all these objects. As kmemleak has been disabled in this case, the object removal and deletion process can be further optimized as locking isn't really needed. However, it is probably not worth the effort to optimize for such an edge case that should rarely happen. So the simple solution is to call cond_resched() at periodic interval in the iteration loop to avoid soft lockup.

In the Linux kernel, the following vulnerability has been resolved: ppp: fix memory leak in pad_compress_skb If alloc_skb() fails in pad_compress_skb(), it returns NULL without releasing the old skb. The caller does: skb = pad_compress_skb(ppp, skb); if (!skb) goto drop; drop: kfree_skb(skb); When pad_compress_skb() returns NULL, the reference to the old skb is lost and kfree_skb(skb) ends up doing nothing, leading to a memory leak. Align pad_compress_skb() semantics with realloc(): only free the old skb if allocation and compression succeed. At the call site, use the new_skb variable so the original skb is not lost when pad_compress_skb() fails.

In the Linux kernel, the following vulnerability has been resolved: drm/nouveau/nvif: Fix potential memory leak in nvif_vmm_ctor(). When the nvif_vmm_type is invalid, we will return error directly without freeing the args in nvif_vmm_ctor(), which leading a memory leak. Fix it by setting the ret -EINVAL and goto done.

In the Linux kernel, the following vulnerability has been resolved: ax25: properly unshare skbs in ax25_kiss_rcv() Bernard Pidoux reported a regression apparently caused by commit c353e8983e0d ("net: introduce per netns packet chains"). skb->dev becomes NULL and we crash in __netif_receive_skb_core(). Before above commit, different kind of bugs or corruptions could happen without a major crash. But the root cause is that ax25_kiss_rcv() can queue/mangle input skb without checking if this skb is shared or not. Many thanks to Bernard Pidoux for his help, diagnosis and tests. We had a similar issue years ago fixed with commit 7aaed57c5c28 ("phonet: properly unshare skbs in phonet_rcv()").

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: HWS, Fix memory leak in hws_pool_buddy_init error path In the error path of hws_pool_buddy_init(), the buddy allocator cleanup doesn't free the allocator structure itself, causing a memory leak. Add the missing kfree() to properly release all allocated memory.

In the Linux kernel, the following vulnerability has been resolved: x86/mce: use is_copy_from_user() to determine copy-from-user context Patch series "mm/hwpoison: Fix regressions in memory failure handling", v4. ## 1. What am I trying to do: This patchset resolves two critical regressions related to memory failure handling that have appeared in the upstream kernel since version 5.17, as compared to 5.10 LTS. - copyin case: poison found in user page while kernel copying from user space - instr case: poison found while instruction fetching in user space ## 2. What is the expected outcome and why - For copyin case: Kernel can recover from poison found where kernel is doing get_user() or copy_from_user() if those places get an error return and the kernel return -EFAULT to the process instead of crashing. More specifily, MCE handler checks the fixup handler type to decide whether an in kernel #MC can be recovered. When EX_TYPE_UACCESS is found, the PC jumps to recovery code specified in _ASM_EXTABLE_FAULT() and return a -EFAULT to user space. - For instr case: If a poison found while instruction fetching in user space, full recovery is possible. User process takes #PF, Linux allocates a new page and fills by reading from storage. ## 3. What actually happens and why - For copyin case: kernel panic since v5.17 Commit 4c132d1d844a ("x86/futex: Remove .fixup usage") introduced a new extable fixup type, EX_TYPE_EFAULT_REG, and later patches updated the extable fixup type for copy-from-user operations, changing it from EX_TYPE_UACCESS to EX_TYPE_EFAULT_REG. It breaks previous EX_TYPE_UACCESS handling when posion found in get_user() or copy_from_user(). - For instr case: user process is killed by a SIGBUS signal due to #CMCI and #MCE race When an uncorrected memory error is consumed there is a race between the CMCI from the memory controller reporting an uncorrected error with a UCNA signature, and the core reporting and SRAR signature machine check when the data is about to be consumed. ### Background: why *UN*corrected errors tied to *C*MCI in Intel platform [1] Prior to Icelake memory controllers reported patrol scrub events that detected a previously unseen uncorrected error in memory by signaling a broadcast machine check with an SRAO (Software Recoverable Action Optional) signature in the machine check bank. This was overkill because it's not an urgent problem that no core is on the verge of consuming that bad data. It's also found that multi SRAO UCE may cause nested MCE interrupts and finally become an IERR. Hence, Intel downgrades the machine check bank signature of patrol scrub from SRAO to UCNA (Uncorrected, No Action required), and signal changed to #CMCI. Just to add to the confusion, Linux does take an action (in uc_decode_notifier()) to try to offline the page despite the UC*NA* signature name. ### Background: why #CMCI and #MCE race when poison is consuming in Intel platform [1] Having decided that CMCI/UCNA is the best action for patrol scrub errors, the memory controller uses it for reads too. But the memory controller is executing asynchronously from the core, and can't tell the difference between a "real" read and a speculative read. So it will do CMCI/UCNA if an error is found in any read. Thus: 1) Core is clever and thinks address A is needed soon, issues a speculative read. 2) Core finds it is going to use address A soon after sending the read request 3) The CMCI from the memory controller is in a race with MCE from the core that will soon try to retire the load from address A. Quite often (because speculation has got better) the CMCI from the memory controller is delivered before the core is committed to the instruction reading address A, so the interrupt is taken, and Linux offlines the page (marking it as poison). ## Why user process is killed for instr case Commit 046545a661af ("mm/hwpoison: fix error page recovered but reported "not ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: HWS, Fix memory leak in hws_action_get_shared_stc_nic error flow When an invalid stc_type is provided, the function allocates memory for shared_stc but jumps to unlock_and_out without freeing it, causing a memory leak. Fix by jumping to free_shared_stc label instead to ensure proper cleanup.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix memory leak in ath12k_service_ready_ext_event Currently, in ath12k_service_ready_ext_event(), svc_rdy_ext.mac_phy_caps is not freed in the failure case, causing a memory leak. The following trace is observed in kmemleak: unreferenced object 0xffff8b3eb5789c00 (size 1024): comm "softirq", pid 0, jiffies 4294942577 hex dump (first 32 bytes): 00 00 00 00 01 00 00 00 00 00 00 00 7b 00 00 10 ............{... 01 00 00 00 00 00 00 00 01 00 00 00 1f 38 00 00 .............8.. backtrace (crc 44e1c357): __kmalloc_noprof+0x30b/0x410 ath12k_wmi_mac_phy_caps_parse+0x84/0x100 [ath12k] ath12k_wmi_tlv_iter+0x5e/0x140 [ath12k] ath12k_wmi_svc_rdy_ext_parse+0x308/0x4c0 [ath12k] ath12k_wmi_tlv_iter+0x5e/0x140 [ath12k] ath12k_service_ready_ext_event.isra.0+0x44/0xd0 [ath12k] ath12k_wmi_op_rx+0x2eb/0xd70 [ath12k] ath12k_htc_rx_completion_handler+0x1f4/0x330 [ath12k] ath12k_ce_recv_process_cb+0x218/0x300 [ath12k] ath12k_pci_ce_workqueue+0x1b/0x30 [ath12k] process_one_work+0x219/0x680 bh_worker+0x198/0x1f0 tasklet_action+0x13/0x30 handle_softirqs+0xca/0x460 __irq_exit_rcu+0xbe/0x110 irq_exit_rcu+0x9/0x30 Free svc_rdy_ext.mac_phy_caps in the error case to fix this memory leak. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1

In the Linux kernel, the following vulnerability has been resolved: fs: Prevent file descriptor table allocations exceeding INT_MAX When sysctl_nr_open is set to a very high value (for example, 1073741816 as set by systemd), processes attempting to use file descriptors near the limit can trigger massive memory allocation attempts that exceed INT_MAX, resulting in a WARNING in mm/slub.c: WARNING: CPU: 0 PID: 44 at mm/slub.c:5027 __kvmalloc_node_noprof+0x21a/0x288 This happens because kvmalloc_array() and kvmalloc() check if the requested size exceeds INT_MAX and emit a warning when the allocation is not flagged with __GFP_NOWARN. Specifically, when nr_open is set to 1073741816 (0x3ffffff8) and a process calls dup2(oldfd, 1073741880), the kernel attempts to allocate: - File descriptor array: 1073741880 * 8 bytes = 8,589,935,040 bytes - Multiple bitmaps: ~400MB - Total allocation size: > 8GB (exceeding INT_MAX = 2,147,483,647) Reproducer: 1. Set /proc/sys/fs/nr_open to 1073741816: # echo 1073741816 > /proc/sys/fs/nr_open 2. Run a program that uses a high file descriptor: #include <unistd.h> #include <sys/resource.h> int main() { struct rlimit rlim = {1073741824, 1073741824}; setrlimit(RLIMIT_NOFILE, &rlim); dup2(2, 1073741880); // Triggers the warning return 0; } 3. Observe WARNING in dmesg at mm/slub.c:5027 systemd commit a8b627a introduced automatic bumping of fs.nr_open to the maximum possible value. The rationale was that systems with memory control groups (memcg) no longer need separate file descriptor limits since memory is properly accounted. However, this change overlooked that: 1. The kernel's allocation functions still enforce INT_MAX as a maximum size regardless of memcg accounting 2. Programs and tests that legitimately test file descriptor limits can inadvertently trigger massive allocations 3. The resulting allocations (>8GB) are impractical and will always fail systemd's algorithm starts with INT_MAX and keeps halving the value until the kernel accepts it. On most systems, this results in nr_open being set to 1073741816 (0x3ffffff8), which is just under 1GB of file descriptors. While processes rarely use file descriptors near this limit in normal operation, certain selftests (like tools/testing/selftests/core/unshare_test.c) and programs that test file descriptor limits can trigger this issue. Fix this by adding a check in alloc_fdtable() to ensure the requested allocation size does not exceed INT_MAX. This causes the operation to fail with -EMFILE instead of triggering a kernel warning and avoids the impractical >8GB memory allocation request.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix memory leak in parse_lease_state() The previous patch that added bounds check for create lease context introduced a memory leak. When the bounds check fails, the function returns NULL without freeing the previously allocated lease_ctx_info structure. This patch fixes the issue by adding kfree(lreq) before returning NULL in both boundary check cases.

In the Linux kernel, the following vulnerability has been resolved: net: lan743x: Fix memleak issue when GSO enabled Always map the `skb` to the LS descriptor. Previously skb was mapped to EXT descriptor when the number of fragments is zero with GSO enabled. Mapping the skb to EXT descriptor prevents it from being freed, leading to a memory leak

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: ti: am65-cpsw-nuss: Fix skb size by accounting for skb_shared_info While transitioning from netdev_alloc_ip_align() to build_skb(), memory for the "skb_shared_info" member of an "skb" was not allocated. Fix this by allocating "PAGE_SIZE" as the skb length, accounting for the packet length, headroom and tailroom, thereby including the required memory space for skb_shared_info.

In the Linux kernel, the following vulnerability has been resolved: net: phy: leds: fix memory leak A network restart test on a router led to an out-of-memory condition, which was traced to a memory leak in the PHY LED trigger code. The root cause is misuse of the devm API. The registration function (phy_led_triggers_register) is called from phy_attach_direct, not phy_probe, and the unregister function (phy_led_triggers_unregister) is called from phy_detach, not phy_remove. This means the register and unregister functions can be called multiple times for the same PHY device, but devm-allocated memory is not freed until the driver is unbound. This also prevents kmemleak from detecting the leak, as the devm API internally stores the allocated pointer. Fix this by replacing devm_kzalloc/devm_kcalloc with standard kzalloc/kcalloc, and add the corresponding kfree calls in the unregister path.

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_ffa: Fix memory leak by freeing notifier callback node Commit e0573444edbf ("firmware: arm_ffa: Add interfaces to request notification callbacks") adds support for notifier callbacks by allocating and inserting a callback node into a hashtable during registration of notifiers. However, during unregistration, the code only removes the node from the hashtable without freeing the associated memory, resulting in a memory leak. Resolve the memory leak issue by ensuring the allocated notifier callback node is properly freed after it is removed from the hashtable entry.