In the Linux kernel, the following vulnerability has been resolved: ASoC: qcom: Fix sc7280 lpass potential buffer overflow Case values introduced in commit 5f78e1fb7a3e ("ASoC: qcom: Add driver support for audioreach solution") cause out of bounds access in arrays of sc7280 driver data (e.g. in case of RX_CODEC_DMA_RX_0 in sc7280_snd_hw_params()). Redefine LPASS_MAX_PORTS to consider the maximum possible port id for q6dsp as sc7280 driver utilizes some of those values. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: iio: accel: fxls8962af: Fix use after free in fxls8962af_fifo_flush fxls8962af_fifo_flush() uses indio_dev->active_scan_mask (with iio_for_each_active_channel()) without making sure the indio_dev stays in buffer mode. There is a race if indio_dev exits buffer mode in the middle of the interrupt that flushes the fifo. Fix this by calling synchronize_irq() to ensure that no interrupt is currently running when disabling buffer mode. Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read [...] _find_first_bit_le from fxls8962af_fifo_flush+0x17c/0x290 fxls8962af_fifo_flush from fxls8962af_interrupt+0x80/0x178 fxls8962af_interrupt from irq_thread_fn+0x1c/0x7c irq_thread_fn from irq_thread+0x110/0x1f4 irq_thread from kthread+0xe0/0xfc kthread from ret_from_fork+0x14/0x2c

In the Linux kernel, the following vulnerability has been resolved: io_uring: fix use-after-free of sq->thread in __io_uring_show_fdinfo() syzbot reports: BUG: KASAN: slab-use-after-free in getrusage+0x1109/0x1a60 Read of size 8 at addr ffff88810de2d2c8 by task a.out/304 CPU: 0 UID: 0 PID: 304 Comm: a.out Not tainted 6.16.0-rc1 #1 PREEMPT(voluntary) Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x53/0x70 print_report+0xd0/0x670 ? __pfx__raw_spin_lock_irqsave+0x10/0x10 ? getrusage+0x1109/0x1a60 kasan_report+0xce/0x100 ? getrusage+0x1109/0x1a60 getrusage+0x1109/0x1a60 ? __pfx_getrusage+0x10/0x10 __io_uring_show_fdinfo+0x9fe/0x1790 ? ksys_read+0xf7/0x1c0 ? do_syscall_64+0xa4/0x260 ? vsnprintf+0x591/0x1100 ? __pfx___io_uring_show_fdinfo+0x10/0x10 ? __pfx_vsnprintf+0x10/0x10 ? mutex_trylock+0xcf/0x130 ? __pfx_mutex_trylock+0x10/0x10 ? __pfx_show_fd_locks+0x10/0x10 ? io_uring_show_fdinfo+0x57/0x80 io_uring_show_fdinfo+0x57/0x80 seq_show+0x38c/0x690 seq_read_iter+0x3f7/0x1180 ? inode_set_ctime_current+0x160/0x4b0 seq_read+0x271/0x3e0 ? __pfx_seq_read+0x10/0x10 ? __pfx__raw_spin_lock+0x10/0x10 ? __mark_inode_dirty+0x402/0x810 ? selinux_file_permission+0x368/0x500 ? file_update_time+0x10f/0x160 vfs_read+0x177/0xa40 ? __pfx___handle_mm_fault+0x10/0x10 ? __pfx_vfs_read+0x10/0x10 ? mutex_lock+0x81/0xe0 ? __pfx_mutex_lock+0x10/0x10 ? fdget_pos+0x24d/0x4b0 ksys_read+0xf7/0x1c0 ? __pfx_ksys_read+0x10/0x10 ? do_user_addr_fault+0x43b/0x9c0 do_syscall_64+0xa4/0x260 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f0f74170fc9 Code: 00 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 8 RSP: 002b:00007fffece049e8 EFLAGS: 00000206 ORIG_RAX: 0000000000000000 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f0f74170fc9 RDX: 0000000000001000 RSI: 00007fffece049f0 RDI: 0000000000000004 RBP: 00007fffece05ad0 R08: 0000000000000000 R09: 00007fffece04d90 R10: 0000000000000000 R11: 0000000000000206 R12: 00005651720a1100 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 </TASK> Allocated by task 298: kasan_save_stack+0x33/0x60 kasan_save_track+0x14/0x30 __kasan_slab_alloc+0x6e/0x70 kmem_cache_alloc_node_noprof+0xe8/0x330 copy_process+0x376/0x5e00 create_io_thread+0xab/0xf0 io_sq_offload_create+0x9ed/0xf20 io_uring_setup+0x12b0/0x1cc0 do_syscall_64+0xa4/0x260 entry_SYSCALL_64_after_hwframe+0x77/0x7f Freed by task 22: kasan_save_stack+0x33/0x60 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3b/0x60 __kasan_slab_free+0x37/0x50 kmem_cache_free+0xc4/0x360 rcu_core+0x5ff/0x19f0 handle_softirqs+0x18c/0x530 run_ksoftirqd+0x20/0x30 smpboot_thread_fn+0x287/0x6c0 kthread+0x30d/0x630 ret_from_fork+0xef/0x1a0 ret_from_fork_asm+0x1a/0x30 Last potentially related work creation: kasan_save_stack+0x33/0x60 kasan_record_aux_stack+0x8c/0xa0 __call_rcu_common.constprop.0+0x68/0x940 __schedule+0xff2/0x2930 __cond_resched+0x4c/0x80 mutex_lock+0x5c/0xe0 io_uring_del_tctx_node+0xe1/0x2b0 io_uring_clean_tctx+0xb7/0x160 io_uring_cancel_generic+0x34e/0x760 do_exit+0x240/0x2350 do_group_exit+0xab/0x220 __x64_sys_exit_group+0x39/0x40 x64_sys_call+0x1243/0x1840 do_syscall_64+0xa4/0x260 entry_SYSCALL_64_after_hwframe+0x77/0x7f The buggy address belongs to the object at ffff88810de2cb00 which belongs to the cache task_struct of size 3712 The buggy address is located 1992 bytes inside of freed 3712-byte region [ffff88810de2cb00, ffff88810de2d980) which is caused by the task_struct pointed to by sq->thread being released while it is being used in the function __io_uring_show_fdinfo(). Holding ctx->uring_lock does not prevent ehre relase or exit of sq->thread. Fix this by assigning and looking up ->thread under RCU, and grabbing a reference to the task_struct. This e ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix use-after-free in session logoff The sess->user object can currently be in use by another thread, for example if another connection has sent a session setup request to bind to the session being free'd. The handler for that connection could be in the smb2_sess_setup function which makes use of sess->user.

In the Linux kernel, the following vulnerability has been resolved: coresight: prevent deactivate active config while enabling the config While enable active config via cscfg_csdev_enable_active_config(), active config could be deactivated via configfs' sysfs interface. This could make UAF issue in below scenario: CPU0 CPU1 (sysfs enable) load module cscfg_load_config_sets() activate config. // sysfs (sys_active_cnt == 1) ... cscfg_csdev_enable_active_config() lock(csdev->cscfg_csdev_lock) // here load config activate by CPU1 unlock(csdev->cscfg_csdev_lock) deactivate config // sysfs (sys_activec_cnt == 0) cscfg_unload_config_sets() unload module // access to config_desc which freed // while unloading module. cscfg_csdev_enable_config To address this, use cscfg_config_desc's active_cnt as a reference count which will be holded when - activate the config. - enable the activated config. and put the module reference when config_active_cnt == 0.

In the Linux kernel, the following vulnerability has been resolved: phy: tegra: xusb: Fix unbalanced regulator disable in UTMI PHY mode When transitioning from USB_ROLE_DEVICE to USB_ROLE_NONE, the code assumed that the regulator should be disabled. However, if the regulator is marked as always-on, regulator_is_enabled() continues to return true, leading to an incorrect attempt to disable a regulator which is not enabled. This can result in warnings such as: [ 250.155624] WARNING: CPU: 1 PID: 7326 at drivers/regulator/core.c:3004 _regulator_disable+0xe4/0x1a0 [ 250.155652] unbalanced disables for VIN_SYS_5V0 To fix this, we move the regulator control logic into tegra186_xusb_padctl_id_override() function since it's directly related to the ID override state. The regulator is now only disabled when the role transitions from USB_ROLE_HOST to USB_ROLE_NONE, by checking the VBUS_ID register. This ensures that regulator enable/disable operations are properly balanced and only occur when actually transitioning to/from host mode.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: Fix UAF in __close_file_table_ids A use-after-free is possible if one thread destroys the file via __ksmbd_close_fd while another thread holds a reference to it. The existing checks on fp->refcount are not sufficient to prevent this. The fix takes ft->lock around the section which removes the file from the file table. This prevents two threads acquiring the same file pointer via __close_file_table_ids, as well as the other functions which retrieve a file from the IDR and which already use this same lock.

In the Linux kernel, the following vulnerability has been resolved: f2fs: compress: fix UAF of f2fs_inode_info in f2fs_free_dic The decompress_io_ctx may be released asynchronously after I/O completion. If this file is deleted immediately after read, and the kworker of processing post_read_wq has not been executed yet due to high workloads, It is possible that the inode(f2fs_inode_info) is evicted and freed before it is used f2fs_free_dic. The UAF case as below: Thread A Thread B - f2fs_decompress_end_io - f2fs_put_dic - queue_work add free_dic work to post_read_wq - do_unlink - iput - evict - call_rcu This file is deleted after read. Thread C kworker to process post_read_wq - rcu_do_batch - f2fs_free_inode - kmem_cache_free inode is freed by rcu - process_scheduled_works - f2fs_late_free_dic - f2fs_free_dic - f2fs_release_decomp_mem read (dic->inode)->i_compress_algorithm This patch store compress_algorithm and sbi in dic to avoid inode UAF. In addition, the previous solution is deprecated in [1] may cause system hang. [1] https://lore.kernel.org/all/c36ab955-c8db-4a8b-a9d0-f07b5f426c3f@kernel.org

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: Set n_channels after allocating struct cfg80211_scan_request Make sure that n_channels is set after allocating the struct cfg80211_registered_device::int_scan_req member. Seen with syzkaller: UBSAN: array-index-out-of-bounds in net/mac80211/scan.c:1208:5 index 0 is out of range for type 'struct ieee80211_channel *[] __counted_by(n_channels)' (aka 'struct ieee80211_channel *[]') This was missed in the initial conversions because I failed to locate the allocation likely due to the "sizeof(void *)" not matching the "channels" array type.

In the Linux kernel, the following vulnerability has been resolved: net: atm: fix /proc/net/atm/lec handling /proc/net/atm/lec must ensure safety against dev_lec[] changes. It appears it had dev_put() calls without prior dev_hold(), leading to imbalance and UAF.

In the Linux kernel, the following vulnerability has been resolved: perf/amlogic: Replace smp_processor_id() with raw_smp_processor_id() in meson_ddr_pmu_create() The Amlogic DDR PMU driver meson_ddr_pmu_create() function incorrectly uses smp_processor_id(), which assumes disabled preemption. This leads to kernel warnings during module loading because meson_ddr_pmu_create() can be called in a preemptible context. Following kernel warning and stack trace: [ 31.745138] [ T2289] BUG: using smp_processor_id() in preemptible [00000000] code: (udev-worker)/2289 [ 31.745154] [ T2289] caller is debug_smp_processor_id+0x28/0x38 [ 31.745172] [ T2289] CPU: 4 UID: 0 PID: 2289 Comm: (udev-worker) Tainted: GW 6.14.0-0-MANJARO-ARM #1 59519addcbca6ba8de735e151fd7b9e97aac7ff0 [ 31.745181] [ T2289] Tainted: [W]=WARN [ 31.745183] [ T2289] Hardware name: Hardkernel ODROID-N2Plus (DT) [ 31.745188] [ T2289] Call trace: [ 31.745191] [ T2289] show_stack+0x28/0x40 (C) [ 31.745199] [ T2289] dump_stack_lvl+0x4c/0x198 [ 31.745205] [ T2289] dump_stack+0x20/0x50 [ 31.745209] [ T2289] check_preemption_disabled+0xec/0xf0 [ 31.745213] [ T2289] debug_smp_processor_id+0x28/0x38 [ 31.745216] [ T2289] meson_ddr_pmu_create+0x200/0x560 [meson_ddr_pmu_g12 8095101c49676ad138d9961e3eddaee10acca7bd] [ 31.745237] [ T2289] g12_ddr_pmu_probe+0x20/0x38 [meson_ddr_pmu_g12 8095101c49676ad138d9961e3eddaee10acca7bd] [ 31.745246] [ T2289] platform_probe+0x98/0xe0 [ 31.745254] [ T2289] really_probe+0x144/0x3f8 [ 31.745258] [ T2289] __driver_probe_device+0xb8/0x180 [ 31.745261] [ T2289] driver_probe_device+0x54/0x268 [ 31.745264] [ T2289] __driver_attach+0x11c/0x288 [ 31.745267] [ T2289] bus_for_each_dev+0xfc/0x160 [ 31.745274] [ T2289] driver_attach+0x34/0x50 [ 31.745277] [ T2289] bus_add_driver+0x160/0x2b0 [ 31.745281] [ T2289] driver_register+0x78/0x120 [ 31.745285] [ T2289] __platform_driver_register+0x30/0x48 [ 31.745288] [ T2289] init_module+0x30/0xfe0 [meson_ddr_pmu_g12 8095101c49676ad138d9961e3eddaee10acca7bd] [ 31.745298] [ T2289] do_one_initcall+0x11c/0x438 [ 31.745303] [ T2289] do_init_module+0x68/0x228 [ 31.745311] [ T2289] load_module+0x118c/0x13a8 [ 31.745315] [ T2289] __arm64_sys_finit_module+0x274/0x390 [ 31.745320] [ T2289] invoke_syscall+0x74/0x108 [ 31.745326] [ T2289] el0_svc_common+0x90/0xf8 [ 31.745330] [ T2289] do_el0_svc+0x2c/0x48 [ 31.745333] [ T2289] el0_svc+0x60/0x150 [ 31.745337] [ T2289] el0t_64_sync_handler+0x80/0x118 [ 31.745341] [ T2289] el0t_64_sync+0x1b8/0x1c0 Changes replaces smp_processor_id() with raw_smp_processor_id() to ensure safe CPU ID retrieval in preemptible contexts.

In the Linux kernel, the following vulnerability has been resolved: tracing: fprobe events: Fix possible UAF on modules Commit ac91052f0ae5 ("tracing: tprobe-events: Fix leakage of module refcount") moved try_module_get() from __find_tracepoint_module_cb() to find_tracepoint() caller, but that introduced a possible UAF because the module can be unloaded before try_module_get(). In this case, the module object should be freed too. Thus, try_module_get() does not only fail but may access to the freed object. To avoid that, try_module_get() in __find_tracepoint_module_cb() again.

In the Linux kernel, the following vulnerability has been resolved: rpl: Fix use-after-free in rpl_do_srh_inline(). Running lwt_dst_cache_ref_loop.sh in selftest with KASAN triggers the splat below [0]. rpl_do_srh_inline() fetches ipv6_hdr(skb) and accesses it after skb_cow_head(), which is illegal as the header could be freed then. Let's fix it by making oldhdr to a local struct instead of a pointer. [0]: [root@fedora net]# ./lwt_dst_cache_ref_loop.sh ... TEST: rpl (input) [ 57.631529] ================================================================== BUG: KASAN: slab-use-after-free in rpl_do_srh_inline.isra.0 (net/ipv6/rpl_iptunnel.c:174) Read of size 40 at addr ffff888122bf96d8 by task ping6/1543 CPU: 50 UID: 0 PID: 1543 Comm: ping6 Not tainted 6.16.0-rc5-01302-gfadd1e6231b1 #23 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Call Trace: <IRQ> dump_stack_lvl (lib/dump_stack.c:122) print_report (mm/kasan/report.c:409 mm/kasan/report.c:521) kasan_report (mm/kasan/report.c:221 mm/kasan/report.c:636) kasan_check_range (mm/kasan/generic.c:175 (discriminator 1) mm/kasan/generic.c:189 (discriminator 1)) __asan_memmove (mm/kasan/shadow.c:94 (discriminator 2)) rpl_do_srh_inline.isra.0 (net/ipv6/rpl_iptunnel.c:174) rpl_input (net/ipv6/rpl_iptunnel.c:201 net/ipv6/rpl_iptunnel.c:282) lwtunnel_input (net/core/lwtunnel.c:459) ipv6_rcv (./include/net/dst.h:471 (discriminator 1) ./include/net/dst.h:469 (discriminator 1) net/ipv6/ip6_input.c:79 (discriminator 1) ./include/linux/netfilter.h:317 (discriminator 1) ./include/linux/netfilter.h:311 (discriminator 1) net/ipv6/ip6_input.c:311 (discriminator 1)) __netif_receive_skb_one_core (net/core/dev.c:5967) process_backlog (./include/linux/rcupdate.h:869 net/core/dev.c:6440) __napi_poll.constprop.0 (net/core/dev.c:7452) net_rx_action (net/core/dev.c:7518 net/core/dev.c:7643) handle_softirqs (kernel/softirq.c:579) do_softirq (kernel/softirq.c:480 (discriminator 20)) </IRQ> <TASK> __local_bh_enable_ip (kernel/softirq.c:407) __dev_queue_xmit (net/core/dev.c:4740) ip6_finish_output2 (./include/linux/netdevice.h:3358 ./include/net/neighbour.h:526 ./include/net/neighbour.h:540 net/ipv6/ip6_output.c:141) ip6_finish_output (net/ipv6/ip6_output.c:215 net/ipv6/ip6_output.c:226) ip6_output (./include/linux/netfilter.h:306 net/ipv6/ip6_output.c:248) ip6_send_skb (net/ipv6/ip6_output.c:1983) rawv6_sendmsg (net/ipv6/raw.c:588 net/ipv6/raw.c:918) __sys_sendto (net/socket.c:714 (discriminator 1) net/socket.c:729 (discriminator 1) net/socket.c:2228 (discriminator 1)) __x64_sys_sendto (net/socket.c:2231) do_syscall_64 (arch/x86/entry/syscall_64.c:63 (discriminator 1) arch/x86/entry/syscall_64.c:94 (discriminator 1)) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) RIP: 0033:0x7f68cffb2a06 Code: 5d e8 41 8b 93 08 03 00 00 59 5e 48 83 f8 fc 75 19 83 e2 39 83 fa 08 75 11 e8 26 ff ff ff 66 0f 1f 44 00 00 48 8b 45 10 0f 05 <48> 8b 5d f8 c9 c3 0f 1f 40 00 f3 0f 1e fa 55 48 89 e5 48 83 ec 08 RSP: 002b:00007ffefb7c53d0 EFLAGS: 00000202 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 0000564cd69f10a0 RCX: 00007f68cffb2a06 RDX: 0000000000000040 RSI: 0000564cd69f10a4 RDI: 0000000000000003 RBP: 00007ffefb7c53f0 R08: 0000564cd6a032ac R09: 000000000000001c R10: 0000000000000000 R11: 0000000000000202 R12: 0000564cd69f10a4 R13: 0000000000000040 R14: 00007ffefb7c66e0 R15: 0000564cd69f10a0 </TASK> Allocated by task 1543: kasan_save_stack (mm/kasan/common.c:48) kasan_save_track (mm/kasan/common.c:60 (discriminator 1) mm/kasan/common.c:69 (discriminator 1)) __kasan_slab_alloc (mm/kasan/common.c:319 mm/kasan/common.c:345) kmem_cache_alloc_node_noprof (./include/linux/kasan.h:250 mm/slub.c:4148 mm/slub.c:4197 mm/slub.c:4249) kmalloc_reserve (net/core/skbuff.c:581 (discriminator 88)) __alloc_skb (net/core/skbuff.c:669) __ip6_append_data (net/ipv6/ip6_output.c:1672 (discriminator 1)) ip6_ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: iio: fix potential out-of-bound write The buffer is set to 20 characters. If a caller write more characters, count is truncated to the max available space in "simple_write_to_buffer". To protect from OoB access, check that the input size fit into buffer and add a zero terminator after copy to the end of the copied data.

In the Linux kernel, the following vulnerability has been resolved: iio: adc: ad4851: fix ad4858 chan pointer handling The pointer returned from ad4851_parse_channels_common() is incremented internally as each channel is populated. In ad4858_parse_channels(), the same pointer was further incremented while setting ext_scan_type fields for each channel. This resulted in indio_dev->channels being set to a pointer past the end of the allocated array, potentially causing memory corruption or undefined behavior. Fix this by iterating over the channels using an explicit index instead of incrementing the pointer. This preserves the original base pointer and ensures all channel metadata is set correctly.

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Avoid potential ndlp use-after-free in dev_loss_tmo_callbk Smatch detected a potential use-after-free of an ndlp oject in dev_loss_tmo_callbk during driver unload or fatal error handling. Fix by reordering code to avoid potential use-after-free if initial nodelist reference has been previously removed.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix use-after-free in cifs_oplock_break A race condition can occur in cifs_oplock_break() leading to a use-after-free of the cinode structure when unmounting: cifs_oplock_break() _cifsFileInfo_put(cfile) cifsFileInfo_put_final() cifs_sb_deactive() [last ref, start releasing sb] kill_sb() kill_anon_super() generic_shutdown_super() evict_inodes() dispose_list() evict() destroy_inode() call_rcu(&inode->i_rcu, i_callback) spin_lock(&cinode->open_file_lock) <- OK [later] i_callback() cifs_free_inode() kmem_cache_free(cinode) spin_unlock(&cinode->open_file_lock) <- UAF cifs_done_oplock_break(cinode) <- UAF The issue occurs when umount has already released its reference to the superblock. When _cifsFileInfo_put() calls cifs_sb_deactive(), this releases the last reference, triggering the immediate cleanup of all inodes under RCU. However, cifs_oplock_break() continues to access the cinode after this point, resulting in use-after-free. Fix this by holding an extra reference to the superblock during the entire oplock break operation. This ensures that the superblock and its inodes remain valid until the oplock break completes.

In the Linux kernel, the following vulnerability has been resolved: RDMA/core: Fix "KASAN: slab-use-after-free Read in ib_register_device" problem Call Trace: __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:408 [inline] print_report+0xc3/0x670 mm/kasan/report.c:521 kasan_report+0xe0/0x110 mm/kasan/report.c:634 strlen+0x93/0xa0 lib/string.c:420 __fortify_strlen include/linux/fortify-string.h:268 [inline] get_kobj_path_length lib/kobject.c:118 [inline] kobject_get_path+0x3f/0x2a0 lib/kobject.c:158 kobject_uevent_env+0x289/0x1870 lib/kobject_uevent.c:545 ib_register_device drivers/infiniband/core/device.c:1472 [inline] ib_register_device+0x8cf/0xe00 drivers/infiniband/core/device.c:1393 rxe_register_device+0x275/0x320 drivers/infiniband/sw/rxe/rxe_verbs.c:1552 rxe_net_add+0x8e/0xe0 drivers/infiniband/sw/rxe/rxe_net.c:550 rxe_newlink+0x70/0x190 drivers/infiniband/sw/rxe/rxe.c:225 nldev_newlink+0x3a3/0x680 drivers/infiniband/core/nldev.c:1796 rdma_nl_rcv_msg+0x387/0x6e0 drivers/infiniband/core/netlink.c:195 rdma_nl_rcv_skb.constprop.0.isra.0+0x2e5/0x450 netlink_unicast_kernel net/netlink/af_netlink.c:1313 [inline] netlink_unicast+0x53a/0x7f0 net/netlink/af_netlink.c:1339 netlink_sendmsg+0x8d1/0xdd0 net/netlink/af_netlink.c:1883 sock_sendmsg_nosec net/socket.c:712 [inline] __sock_sendmsg net/socket.c:727 [inline] ____sys_sendmsg+0xa95/0xc70 net/socket.c:2566 ___sys_sendmsg+0x134/0x1d0 net/socket.c:2620 __sys_sendmsg+0x16d/0x220 net/socket.c:2652 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xcd/0x260 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f This problem is similar to the problem that the commit 1d6a9e7449e2 ("RDMA/core: Fix use-after-free when rename device name") fixes. The root cause is: the function ib_device_rename() renames the name with lock. But in the function kobject_uevent(), this name is accessed without lock protection at the same time. The solution is to add the lock protection when this name is accessed in the function kobject_uevent().

In the Linux kernel, the following vulnerability has been resolved: scsi: smartpqi: Use is_kdump_kernel() to check for kdump The smartpqi driver checks the reset_devices variable to determine whether special adjustments need to be made for kdump. This has the effect that after a regular kexec reboot, some driver parameters such as max_transfer_size are much lower than usual. More importantly, kexec reboot tests have revealed memory corruption caused by the driver log being written to system memory after a kexec. Fix this by testing is_kdump_kernel() rather than reset_devices where appropriate.

In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: gadget: check that event count does not exceed event buffer length The event count is read from register DWC3_GEVNTCOUNT. There is a check for the count being zero, but not for exceeding the event buffer length. Check that event count does not exceed event buffer length, avoiding an out-of-bounds access when memcpy'ing the event. Crash log: Unable to handle kernel paging request at virtual address ffffffc0129be000 pc : __memcpy+0x114/0x180 lr : dwc3_check_event_buf+0xec/0x348 x3 : 0000000000000030 x2 : 000000000000dfc4 x1 : ffffffc0129be000 x0 : ffffff87aad60080 Call trace: __memcpy+0x114/0x180 dwc3_interrupt+0x24/0x34

In the Linux kernel, the following vulnerability has been resolved: tracing: Fix oob write in trace_seq_to_buffer() syzbot reported this bug: ================================================================== BUG: KASAN: slab-out-of-bounds in trace_seq_to_buffer kernel/trace/trace.c:1830 [inline] BUG: KASAN: slab-out-of-bounds in tracing_splice_read_pipe+0x6be/0xdd0 kernel/trace/trace.c:6822 Write of size 4507 at addr ffff888032b6b000 by task syz.2.320/7260 CPU: 1 UID: 0 PID: 7260 Comm: syz.2.320 Not tainted 6.15.0-rc1-syzkaller-00301-g3bde70a2c827 #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:408 [inline] print_report+0xc3/0x670 mm/kasan/report.c:521 kasan_report+0xe0/0x110 mm/kasan/report.c:634 check_region_inline mm/kasan/generic.c:183 [inline] kasan_check_range+0xef/0x1a0 mm/kasan/generic.c:189 __asan_memcpy+0x3c/0x60 mm/kasan/shadow.c:106 trace_seq_to_buffer kernel/trace/trace.c:1830 [inline] tracing_splice_read_pipe+0x6be/0xdd0 kernel/trace/trace.c:6822 .... ================================================================== It has been reported that trace_seq_to_buffer() tries to copy more data than PAGE_SIZE to buf. Therefore, to prevent this, we should use the smaller of trace_seq_used(&iter->seq) and PAGE_SIZE as an argument.

In the Linux kernel, the following vulnerability has been resolved: iommu/amd: Fix potential buffer overflow in parse_ivrs_acpihid There is a string parsing logic error which can lead to an overflow of hid or uid buffers. Comparing ACPIID_LEN against a total string length doesn't take into account the lengths of individual hid and uid buffers so the check is insufficient in some cases. For example if the length of hid string is 4 and the length of the uid string is 260, the length of str will be equal to ACPIID_LEN + 1 but uid string will overflow uid buffer which size is 256. The same applies to the hid string with length 13 and uid string with length 250. Check the length of hid and uid strings separately to prevent buffer overflow. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: zloop: fix KASAN use-after-free of tag set When a zoned loop device, or zloop device, is removed, KASAN enabled kernel reports "BUG KASAN use-after-free" in blk_mq_free_tag_set(). The BUG happens because zloop_ctl_remove() calls put_disk(), which invokes zloop_free_disk(). The zloop_free_disk() frees the memory allocated for the zlo pointer. However, after the memory is freed, zloop_ctl_remove() calls blk_mq_free_tag_set(&zlo->tag_set), which accesses the freed zlo. Hence the KASAN use-after-free. zloop_ctl_remove() put_disk(zlo->disk) put_device() kobject_put() ... zloop_free_disk() kvfree(zlo) blk_mq_free_tag_set(&zlo->tag_set) To avoid the BUG, move the call to blk_mq_free_tag_set(&zlo->tag_set) from zloop_ctl_remove() into zloop_free_disk(). This ensures that the tag_set is freed before the call to kvfree(zlo).

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Reset IRTE to host control if *new* route isn't postable Restore an IRTE back to host control (remapped or posted MSI mode) if the *new* GSI route prevents posting the IRQ directly to a vCPU, regardless of the GSI routing type. Updating the IRTE if and only if the new GSI is an MSI results in KVM leaving an IRTE posting to a vCPU. The dangling IRTE can result in interrupts being incorrectly delivered to the guest, and in the worst case scenario can result in use-after-free, e.g. if the VM is torn down, but the underlying host IRQ isn't freed.

In the Linux kernel, the following vulnerability has been resolved: net: libwx: fix the using of Rx buffer DMA The wx_rx_buffer structure contained two DMA address fields: 'dma' and 'page_dma'. However, only 'page_dma' was actually initialized and used to program the Rx descriptor. But 'dma' was uninitialized and used in some paths. This could lead to undefined behavior, including DMA errors or use-after-free, if the uninitialized 'dma' was used. Althrough such error has not yet occurred, it is worth fixing in the code.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: Fix dangling pointer in krb_authenticate krb_authenticate frees sess->user and does not set the pointer to NULL. It calls ksmbd_krb5_authenticate to reinitialise sess->user but that function may return without doing so. If that happens then smb2_sess_setup, which calls krb_authenticate, will be accessing free'd memory when it later uses sess->user.

In the Linux kernel, the following vulnerability has been resolved: bus: fsl-mc: fix double-free on mc_dev The blamed commit tried to simplify how the deallocations are done but, in the process, introduced a double-free on the mc_dev variable. In case the MC device is a DPRC, a new mc_bus is allocated and the mc_dev variable is just a reference to one of its fields. In this circumstance, on the error path only the mc_bus should be freed. This commit introduces back the following checkpatch warning which is a false-positive. WARNING: kfree(NULL) is safe and this check is probably not required + if (mc_bus) + kfree(mc_bus);

In the Linux kernel, the following vulnerability has been resolved: net: openvswitch: fix nested key length validation in the set() action It's not safe to access nla_len(ovs_key) if the data is smaller than the netlink header. Check that the attribute is OK first.

In the Linux kernel, the following vulnerability has been resolved: netfs: Fix double put of request If a netfs request finishes during the pause loop, it will have the ref that belongs to the IN_PROGRESS flag removed at that point - however, if it then goes to the final wait loop, that will *also* put the ref because it sees that the IN_PROGRESS flag is clear and incorrectly assumes that this happened when it called the collector. In fact, since IN_PROGRESS is clear, we shouldn't call the collector again since it's done all the cleanup, such as calling ->ki_complete(). Fix this by making netfs_collect_in_app() just return, indicating that we're done if IN_PROGRESS is removed.

In the Linux kernel, the following vulnerability has been resolved: HID: appletb-kbd: fix memory corruption of input_handler_list In appletb_kbd_probe an input handler is initialised and then registered with input core through input_register_handler(). When this happens input core will add the input handler (specifically its node) to the global input_handler_list. The input_handler_list is central to the functionality of input core and is traversed in various places in input core. An example of this is when a new input device is plugged in and gets registered with input core. The input_handler in probe is allocated as device managed memory. If a probe failure occurs after input_register_handler() the input_handler memory is freed, yet it will remain in the input_handler_list. This effectively means the input_handler_list contains a dangling pointer to data belonging to a freed input handler. This causes an issue when any other input device is plugged in - in my case I had an old PixArt HP USB optical mouse and I decided to plug it in after a failure occurred after input_register_handler(). This lead to the registration of this input device via input_register_device which involves traversing over every handler in the corrupted input_handler_list and calling input_attach_handler(), giving each handler a chance to bind to newly registered device. The core of this bug is a UAF which causes memory corruption of input_handler_list and to fix it we must ensure the input handler is unregistered from input core, this is done through input_unregister_handler(). [ 63.191597] ================================================================== [ 63.192094] BUG: KASAN: slab-use-after-free in input_attach_handler.isra.0+0x1a9/0x1e0 [ 63.192094] Read of size 8 at addr ffff888105ea7c80 by task kworker/0:2/54 [ 63.192094] [ 63.192094] CPU: 0 UID: 0 PID: 54 Comm: kworker/0:2 Not tainted 6.16.0-rc2-00321-g2aa6621d [ 63.192094] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.164 [ 63.192094] Workqueue: usb_hub_wq hub_event [ 63.192094] Call Trace: [ 63.192094] <TASK> [ 63.192094] dump_stack_lvl+0x53/0x70 [ 63.192094] print_report+0xce/0x670 [ 63.192094] kasan_report+0xce/0x100 [ 63.192094] input_attach_handler.isra.0+0x1a9/0x1e0 [ 63.192094] input_register_device+0x76c/0xd00 [ 63.192094] hidinput_connect+0x686d/0xad60 [ 63.192094] hid_connect+0xf20/0x1b10 [ 63.192094] hid_hw_start+0x83/0x100 [ 63.192094] hid_device_probe+0x2d1/0x680 [ 63.192094] really_probe+0x1c3/0x690 [ 63.192094] __driver_probe_device+0x247/0x300 [ 63.192094] driver_probe_device+0x49/0x210 [ 63.192094] __device_attach_driver+0x160/0x320 [ 63.192094] bus_for_each_drv+0x10f/0x190 [ 63.192094] __device_attach+0x18e/0x370 [ 63.192094] bus_probe_device+0x123/0x170 [ 63.192094] device_add+0xd4d/0x1460 [ 63.192094] hid_add_device+0x30b/0x910 [ 63.192094] usbhid_probe+0x920/0xe00 [ 63.192094] usb_probe_interface+0x363/0x9a0 [ 63.192094] really_probe+0x1c3/0x690 [ 63.192094] __driver_probe_device+0x247/0x300 [ 63.192094] driver_probe_device+0x49/0x210 [ 63.192094] __device_attach_driver+0x160/0x320 [ 63.192094] bus_for_each_drv+0x10f/0x190 [ 63.192094] __device_attach+0x18e/0x370 [ 63.192094] bus_probe_device+0x123/0x170 [ 63.192094] device_add+0xd4d/0x1460 [ 63.192094] usb_set_configuration+0xd14/0x1880 [ 63.192094] usb_generic_driver_probe+0x78/0xb0 [ 63.192094] usb_probe_device+0xaa/0x2e0 [ 63.192094] really_probe+0x1c3/0x690 [ 63.192094] __driver_probe_device+0x247/0x300 [ 63.192094] driver_probe_device+0x49/0x210 [ 63.192094] __device_attach_driver+0x160/0x320 [ 63.192094] bus_for_each_drv+0x10f/0x190 [ 63.192094] __device_attach+0x18e/0x370 [ 63.192094] bus_probe_device+0x123/0x170 [ 63.192094] device_add+0xd4d/0x1460 [ 63.192094] usb_new_device+0x7b4/0x1000 [ 63.192094] hub_event+0x234d/0x3 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: udmabuf: fix a buf size overflow issue during udmabuf creation by casting size_limit_mb to u64 when calculate pglimit.

In the Linux kernel, the following vulnerability has been resolved: ipc: fix to protect IPCS lookups using RCU syzbot reported that it discovered a use-after-free vulnerability, [0] [0]: https://lore.kernel.org/all/67af13f8.050a0220.21dd3.0038.GAE@google.com/ idr_for_each() is protected by rwsem, but this is not enough. If it is not protected by RCU read-critical region, when idr_for_each() calls radix_tree_node_free() through call_rcu() to free the radix_tree_node structure, the node will be freed immediately, and when reading the next node in radix_tree_for_each_slot(), the already freed memory may be read. Therefore, we need to add code to make sure that idr_for_each() is protected within the RCU read-critical region when we call it in shm_destroy_orphaned().

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check dce_hwseq before dereferencing it [WHAT] hws was checked for null earlier in dce110_blank_stream, indicating hws can be null, and should be checked whenever it is used. (cherry picked from commit 79db43611ff61280b6de58ce1305e0b2ecf675ad)

In the Linux kernel, the following vulnerability has been resolved: bpf: Avoid __bpf_prog_ret0_warn when jit fails syzkaller reported an issue: WARNING: CPU: 3 PID: 217 at kernel/bpf/core.c:2357 __bpf_prog_ret0_warn+0xa/0x20 kernel/bpf/core.c:2357 Modules linked in: CPU: 3 UID: 0 PID: 217 Comm: kworker/u32:6 Not tainted 6.15.0-rc4-syzkaller-00040-g8bac8898fe39 RIP: 0010:__bpf_prog_ret0_warn+0xa/0x20 kernel/bpf/core.c:2357 Call Trace: <TASK> bpf_dispatcher_nop_func include/linux/bpf.h:1316 [inline] __bpf_prog_run include/linux/filter.h:718 [inline] bpf_prog_run include/linux/filter.h:725 [inline] cls_bpf_classify+0x74a/0x1110 net/sched/cls_bpf.c:105 ... When creating bpf program, 'fp->jit_requested' depends on bpf_jit_enable. This issue is triggered because of CONFIG_BPF_JIT_ALWAYS_ON is not set and bpf_jit_enable is set to 1, causing the arch to attempt JIT the prog, but jit failed due to FAULT_INJECTION. As a result, incorrectly treats the program as valid, when the program runs it calls `__bpf_prog_ret0_warn` and triggers the WARN_ON_ONCE(1).

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Restore context entry setup order for aliased devices Commit 2031c469f816 ("iommu/vt-d: Add support for static identity domain") changed the context entry setup during domain attachment from a set-and-check policy to a clear-and-reset approach. This inadvertently introduced a regression affecting PCI aliased devices behind PCIe-to-PCI bridges. Specifically, keyboard and touchpad stopped working on several Apple Macbooks with below messages: kernel: platform pxa2xx-spi.3: Adding to iommu group 20 kernel: input: Apple SPI Keyboard as /devices/pci0000:00/0000:00:1e.3/pxa2xx-spi.3/spi_master/spi2/spi-APP000D:00/input/input0 kernel: DMAR: DRHD: handling fault status reg 3 kernel: DMAR: [DMA Read NO_PASID] Request device [00:1e.3] fault addr 0xffffa000 [fault reason 0x06] PTE Read access is not set kernel: DMAR: DRHD: handling fault status reg 3 kernel: DMAR: [DMA Read NO_PASID] Request device [00:1e.3] fault addr 0xffffa000 [fault reason 0x06] PTE Read access is not set kernel: applespi spi-APP000D:00: Error writing to device: 01 0e 00 00 kernel: DMAR: DRHD: handling fault status reg 3 kernel: DMAR: [DMA Read NO_PASID] Request device [00:1e.3] fault addr 0xffffa000 [fault reason 0x06] PTE Read access is not set kernel: DMAR: DRHD: handling fault status reg 3 kernel: applespi spi-APP000D:00: Error writing to device: 01 0e 00 00 Fix this by restoring the previous context setup order.

In the Linux kernel, the following vulnerability has been resolved: HID: core: do not bypass hid_hw_raw_request hid_hw_raw_request() is actually useful to ensure the provided buffer and length are valid. Directly calling in the low level transport driver function bypassed those checks and allowed invalid paramto be used.

In the Linux kernel, the following vulnerability has been resolved: sch_hfsc: Fix qlen accounting bug when using peek in hfsc_enqueue() When enqueuing the first packet to an HFSC class, hfsc_enqueue() calls the child qdisc's peek() operation before incrementing sch->q.qlen and sch->qstats.backlog. If the child qdisc uses qdisc_peek_dequeued(), this may trigger an immediate dequeue and potential packet drop. In such cases, qdisc_tree_reduce_backlog() is called, but the HFSC qdisc's qlen and backlog have not yet been updated, leading to inconsistent queue accounting. This can leave an empty HFSC class in the active list, causing further consequences like use-after-free. This patch fixes the bug by moving the increment of sch->q.qlen and sch->qstats.backlog before the call to the child qdisc's peek() operation. This ensures that queue length and backlog are always accurate when packet drops or dequeues are triggered during the peek.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: MGMT: Fix UAF on mgmt_remove_adv_monitor_complete This reworks MGMT_OP_REMOVE_ADV_MONITOR to not use mgmt_pending_add to avoid crashes like bellow: ================================================================== BUG: KASAN: slab-use-after-free in mgmt_remove_adv_monitor_complete+0xe5/0x540 net/bluetooth/mgmt.c:5406 Read of size 8 at addr ffff88801c53f318 by task kworker/u5:5/5341 CPU: 0 UID: 0 PID: 5341 Comm: kworker/u5:5 Not tainted 6.15.0-syzkaller-10402-g4cb6c8af8591 #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:408 [inline] print_report+0xd2/0x2b0 mm/kasan/report.c:521 kasan_report+0x118/0x150 mm/kasan/report.c:634 mgmt_remove_adv_monitor_complete+0xe5/0x540 net/bluetooth/mgmt.c:5406 hci_cmd_sync_work+0x261/0x3a0 net/bluetooth/hci_sync.c:334 process_one_work kernel/workqueue.c:3238 [inline] process_scheduled_works+0xade/0x17b0 kernel/workqueue.c:3321 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3402 kthread+0x711/0x8a0 kernel/kthread.c:464 ret_from_fork+0x3fc/0x770 arch/x86/kernel/process.c:148 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK> Allocated by task 5987: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:68 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:394 kasan_kmalloc include/linux/kasan.h:260 [inline] __kmalloc_cache_noprof+0x230/0x3d0 mm/slub.c:4358 kmalloc_noprof include/linux/slab.h:905 [inline] kzalloc_noprof include/linux/slab.h:1039 [inline] mgmt_pending_new+0x65/0x240 net/bluetooth/mgmt_util.c:252 mgmt_pending_add+0x34/0x120 net/bluetooth/mgmt_util.c:279 remove_adv_monitor+0x103/0x1b0 net/bluetooth/mgmt.c:5454 hci_mgmt_cmd+0x9c9/0xef0 net/bluetooth/hci_sock.c:1719 hci_sock_sendmsg+0x6ca/0xef0 net/bluetooth/hci_sock.c:1839 sock_sendmsg_nosec net/socket.c:712 [inline] __sock_sendmsg+0x219/0x270 net/socket.c:727 sock_write_iter+0x258/0x330 net/socket.c:1131 new_sync_write fs/read_write.c:593 [inline] vfs_write+0x548/0xa90 fs/read_write.c:686 ksys_write+0x145/0x250 fs/read_write.c:738 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f Freed by task 5989: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:68 kasan_save_free_info+0x46/0x50 mm/kasan/generic.c:576 poison_slab_object mm/kasan/common.c:247 [inline] __kasan_slab_free+0x62/0x70 mm/kasan/common.c:264 kasan_slab_free include/linux/kasan.h:233 [inline] slab_free_hook mm/slub.c:2380 [inline] slab_free mm/slub.c:4642 [inline] kfree+0x18e/0x440 mm/slub.c:4841 mgmt_pending_foreach+0xc9/0x120 net/bluetooth/mgmt_util.c:242 mgmt_index_removed+0x10d/0x2f0 net/bluetooth/mgmt.c:9366 hci_sock_bind+0xbe9/0x1000 net/bluetooth/hci_sock.c:1314 __sys_bind_socket net/socket.c:1810 [inline] __sys_bind+0x2c3/0x3e0 net/socket.c:1841 __do_sys_bind net/socket.c:1846 [inline] __se_sys_bind net/socket.c:1844 [inline] __x64_sys_bind+0x7a/0x90 net/socket.c:1844 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: perf/core: Exit early on perf_mmap() fail When perf_mmap() fails to allocate a buffer, it still invokes the event_mapped() callback of the related event. On X86 this might increase the perf_rdpmc_allowed reference counter. But nothing undoes this as perf_mmap_close() is never called in this case, which causes another reference count leak. Return early on failure to prevent that.

In the Linux kernel, the following vulnerability has been resolved: xen: fix UAF in dmabuf_exp_from_pages() [dma_buf_fd() fixes; no preferences regarding the tree it goes through - up to xen folks] As soon as we'd inserted a file reference into descriptor table, another thread could close it. That's fine for the case when all we are doing is returning that descriptor to userland (it's a race, but it's a userland race and there's nothing the kernel can do about it). However, if we follow fd_install() with any kind of access to objects that would be destroyed on close (be it the struct file itself or anything destroyed by its ->release()), we have a UAF. dma_buf_fd() is a combination of reserving a descriptor and fd_install(). gntdev dmabuf_exp_from_pages() calls it and then proceeds to access the objects destroyed on close - starting with gntdev_dmabuf itself. Fix that by doing reserving descriptor before anything else and do fd_install() only when everything had been set up.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sync: fix double free in 'hci_discovery_filter_clear()' Function 'hci_discovery_filter_clear()' frees 'uuids' array and then sets it to NULL. There is a tiny chance of the following race: 'hci_cmd_sync_work()' 'update_passive_scan_sync()' 'hci_update_passive_scan_sync()' 'hci_discovery_filter_clear()' kfree(uuids); <-------------------------preempted--------------------------------> 'start_service_discovery()' 'hci_discovery_filter_clear()' kfree(uuids); // DOUBLE FREE <-------------------------preempted--------------------------------> uuids = NULL; To fix it let's add locking around 'kfree()' call and NULL pointer assignment. Otherwise the following backtrace fires: [ ] ------------[ cut here ]------------ [ ] kernel BUG at mm/slub.c:547! [ ] Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP [ ] CPU: 3 UID: 0 PID: 246 Comm: bluetoothd Tainted: G O 6.12.19-kernel #1 [ ] Tainted: [O]=OOT_MODULE [ ] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ ] pc : __slab_free+0xf8/0x348 [ ] lr : __slab_free+0x48/0x348 ... [ ] Call trace: [ ] __slab_free+0xf8/0x348 [ ] kfree+0x164/0x27c [ ] start_service_discovery+0x1d0/0x2c0 [ ] hci_sock_sendmsg+0x518/0x924 [ ] __sock_sendmsg+0x54/0x60 [ ] sock_write_iter+0x98/0xf8 [ ] do_iter_readv_writev+0xe4/0x1c8 [ ] vfs_writev+0x128/0x2b0 [ ] do_writev+0xfc/0x118 [ ] __arm64_sys_writev+0x20/0x2c [ ] invoke_syscall+0x68/0xf0 [ ] el0_svc_common.constprop.0+0x40/0xe0 [ ] do_el0_svc+0x1c/0x28 [ ] el0_svc+0x30/0xd0 [ ] el0t_64_sync_handler+0x100/0x12c [ ] el0t_64_sync+0x194/0x198 [ ] Code: 8b0002e6 eb17031f 54fffbe1 d503201f (d4210000) [ ] ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix uaf in ath12k_core_init() When the execution of ath12k_core_hw_group_assign() or ath12k_core_hw_group_create() fails, the registered notifier chain is not unregistered properly. Its memory is freed after rmmod, which may trigger to a use-after-free (UAF) issue if there is a subsequent access to this notifier chain. Fixes the issue by calling ath12k_core_panic_notifier_unregister() in failure cases. Call trace: notifier_chain_register+0x4c/0x1f0 (P) atomic_notifier_chain_register+0x38/0x68 ath12k_core_init+0x50/0x4e8 [ath12k] ath12k_pci_probe+0x5f8/0xc28 [ath12k] pci_device_probe+0xbc/0x1a8 really_probe+0xc8/0x3a0 __driver_probe_device+0x84/0x1b0 driver_probe_device+0x44/0x130 __driver_attach+0xcc/0x208 bus_for_each_dev+0x84/0x100 driver_attach+0x2c/0x40 bus_add_driver+0x130/0x260 driver_register+0x70/0x138 __pci_register_driver+0x68/0x80 ath12k_pci_init+0x30/0x68 [ath12k] ath12k_init+0x28/0x78 [ath12k] Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

In the Linux kernel, the following vulnerability has been resolved: binder: fix yet another UAF in binder_devices Commit e77aff5528a18 ("binderfs: fix use-after-free in binder_devices") addressed a use-after-free where devices could be released without first being removed from the binder_devices list. However, there is a similar path in binder_free_proc() that was missed: ================================================================== BUG: KASAN: slab-use-after-free in binder_remove_device+0xd4/0x100 Write of size 8 at addr ffff0000c773b900 by task umount/467 CPU: 12 UID: 0 PID: 467 Comm: umount Not tainted 6.15.0-rc7-00138-g57483a362741 #9 PREEMPT Hardware name: linux,dummy-virt (DT) Call trace: binder_remove_device+0xd4/0x100 binderfs_evict_inode+0x230/0x2f0 evict+0x25c/0x5dc iput+0x304/0x480 dentry_unlink_inode+0x208/0x46c __dentry_kill+0x154/0x530 [...] Allocated by task 463: __kmalloc_cache_noprof+0x13c/0x324 binderfs_binder_device_create.isra.0+0x138/0xa60 binder_ctl_ioctl+0x1ac/0x230 [...] Freed by task 215: kfree+0x184/0x31c binder_proc_dec_tmpref+0x33c/0x4ac binder_deferred_func+0xc10/0x1108 process_one_work+0x520/0xba4 [...] ================================================================== Call binder_remove_device() within binder_free_proc() to ensure the device is removed from the binder_devices list before being kfreed.

The tpacket_rcv function in net/packet/af_packet.c in the Linux kernel before 4.13 mishandles vnet headers, which might allow local users to cause a denial of service (buffer overflow, and disk and memory corruption) or possibly have unspecified other impact via crafted system calls.

In the Linux kernel, the following vulnerability has been resolved: crypto: lzo - Fix compression buffer overrun Unlike the decompression code, the compression code in LZO never checked for output overruns. It instead assumes that the caller always provides enough buffer space, disregarding the buffer length provided by the caller. Add a safe compression interface that checks for the end of buffer before each write. Use the safe interface in crypto/lzo.

In the Linux kernel, the following vulnerability has been resolved: net_sched: hfsc: Fix a UAF vulnerability in class with netem as child qdisc As described in Gerrard's report [1], we have a UAF case when an hfsc class has a netem child qdisc. The crux of the issue is that hfsc is assuming that checking for cl->qdisc->q.qlen == 0 guarantees that it hasn't inserted the class in the vttree or eltree (which is not true for the netem duplicate case). This patch checks the n_active class variable to make sure that the code won't insert the class in the vttree or eltree twice, catering for the reentrant case. [1] https://lore.kernel.org/netdev/CAHcdcOm+03OD2j6R0=YHKqmy=VgJ8xEOKuP6c7mSgnp-TEJJbw@mail.gmail.com/

In the Linux kernel, the following vulnerability has been resolved: codel: remove sch->q.qlen check before qdisc_tree_reduce_backlog() After making all ->qlen_notify() callbacks idempotent, now it is safe to remove the check of qlen!=0 from both fq_codel_dequeue() and codel_qdisc_dequeue().

In the Linux kernel, the following vulnerability has been resolved: ALSA: ump: Fix buffer overflow at UMP SysEx message conversion The conversion function from MIDI 1.0 to UMP packet contains an internal buffer to keep the incoming MIDI bytes, and its size is 4, as it was supposed to be the max size for a MIDI1 UMP packet data. However, the implementation overlooked that SysEx is handled in a different format, and it can be up to 6 bytes, as found in do_convert_to_ump(). It leads eventually to a buffer overflow, and may corrupt the memory when a longer SysEx message is received. The fix is simply to extend the buffer size to 6 to fit with the SysEx UMP message.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: prevent out-of-bounds stream writes by validating *pos ksmbd_vfs_stream_write() did not validate whether the write offset (*pos) was within the bounds of the existing stream data length (v_len). If *pos was greater than or equal to v_len, this could lead to an out-of-bounds memory write. This patch adds a check to ensure *pos is less than v_len before proceeding. If the condition fails, -EINVAL is returned.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix UAF in decryption with multichannel After commit f7025d861694 ("smb: client: allocate crypto only for primary server") and commit b0abcd65ec54 ("smb: client: fix UAF in async decryption"), the channels started reusing AEAD TFM from primary channel to perform synchronous decryption, but that can't done as there could be multiple cifsd threads (one per channel) simultaneously accessing it to perform decryption. This fixes the following KASAN splat when running fstest generic/249 with 'vers=3.1.1,multichannel,max_channels=4,seal' against Windows Server 2022: BUG: KASAN: slab-use-after-free in gf128mul_4k_lle+0xba/0x110 Read of size 8 at addr ffff8881046c18a0 by task cifsd/986 CPU: 3 UID: 0 PID: 986 Comm: cifsd Not tainted 6.15.0-rc1 #1 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-3.fc41 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x5d/0x80 print_report+0x156/0x528 ? gf128mul_4k_lle+0xba/0x110 ? __virt_addr_valid+0x145/0x300 ? __phys_addr+0x46/0x90 ? gf128mul_4k_lle+0xba/0x110 kasan_report+0xdf/0x1a0 ? gf128mul_4k_lle+0xba/0x110 gf128mul_4k_lle+0xba/0x110 ghash_update+0x189/0x210 shash_ahash_update+0x295/0x370 ? __pfx_shash_ahash_update+0x10/0x10 ? __pfx_shash_ahash_update+0x10/0x10 ? __pfx_extract_iter_to_sg+0x10/0x10 ? ___kmalloc_large_node+0x10e/0x180 ? __asan_memset+0x23/0x50 crypto_ahash_update+0x3c/0xc0 gcm_hash_assoc_remain_continue+0x93/0xc0 crypt_message+0xe09/0xec0 [cifs] ? __pfx_crypt_message+0x10/0x10 [cifs] ? _raw_spin_unlock+0x23/0x40 ? __pfx_cifs_readv_from_socket+0x10/0x10 [cifs] decrypt_raw_data+0x229/0x380 [cifs] ? __pfx_decrypt_raw_data+0x10/0x10 [cifs] ? __pfx_cifs_read_iter_from_socket+0x10/0x10 [cifs] smb3_receive_transform+0x837/0xc80 [cifs] ? __pfx_smb3_receive_transform+0x10/0x10 [cifs] ? __pfx___might_resched+0x10/0x10 ? __pfx_smb3_is_transform_hdr+0x10/0x10 [cifs] cifs_demultiplex_thread+0x692/0x1570 [cifs] ? __pfx_cifs_demultiplex_thread+0x10/0x10 [cifs] ? rcu_is_watching+0x20/0x50 ? rcu_lockdep_current_cpu_online+0x62/0xb0 ? find_held_lock+0x32/0x90 ? kvm_sched_clock_read+0x11/0x20 ? local_clock_noinstr+0xd/0xd0 ? trace_irq_enable.constprop.0+0xa8/0xe0 ? __pfx_cifs_demultiplex_thread+0x10/0x10 [cifs] kthread+0x1fe/0x380 ? kthread+0x10f/0x380 ? __pfx_kthread+0x10/0x10 ? local_clock_noinstr+0xd/0xd0 ? ret_from_fork+0x1b/0x60 ? local_clock+0x15/0x30 ? lock_release+0x29b/0x390 ? rcu_is_watching+0x20/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x31/0x60 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK>