A vulnerability in the Network-Based Application Recognition (NBAR) feature of Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload, causing a denial of service (DoS) condition. This vulnerability is due to improper handling of malformed Control and Provisioning of Wireless Access Points (CAPWAP) packets. An attacker could exploit this vulnerability by sending malformed CAPWAP packets through an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition.

A vulnerability in SSL/TLS message handler for Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability exists because incoming SSL/TLS packets are not properly processed. An attacker could exploit this vulnerability by sending a crafted SSL/TLS packet to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition.

A vulnerability in the software-based SSL/TLS message handler of Cisco Adaptive Security Appliance (ASA) Software and Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. This vulnerability is due to insufficient validation of SSL/TLS messages when the device performs software-based SSL/TLS decryption. An attacker could exploit this vulnerability by sending a crafted SSL/TLS message to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Note: Datagram TLS (DTLS) messages cannot be used to exploit this vulnerability.

A vulnerability in the processing of SSH connections for multi-instance deployments of Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on the affected device. This vulnerability is due to a lack of proper error handling when an SSH session fails to be established. An attacker could exploit this vulnerability by sending a high rate of crafted SSH connections to the instance. A successful exploit could allow the attacker to cause resource exhaustion, which causes a DoS condition on the affected device. The device must be manually reloaded to recover.

A vulnerability in dynamic access policies (DAP) functionality of Cisco Adaptive Security Appliance (ASA) Software and Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. This vulnerability is due to improper processing of HostScan data received from the Posture (HostScan) module. An attacker could exploit this vulnerability by sending crafted HostScan data to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. https://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-asa-ftd-dap-dos-GhYZBxDU ["https://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-asa-ftd-dap-dos-GhYZBxDU"] This advisory is part of the November 2022 release of the Cisco ASA, FTD, and FMC Security Advisory Bundled publication.

Multiple vulnerabilities in Cisco SD-WAN products could allow an unauthenticated, remote attacker to execute denial of service (DoS) attacks against an affected device. For more information about these vulnerabilities, see the Details section of this advisory.

A vulnerability in the software-based SSL/TLS message handler of Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to trigger a reload of an affected device, resulting in a denial of service (DoS) condition. The vulnerability is due to insufficient validation of SSL/TLS messages when the device performs software-based SSL decryption. An attacker could exploit this vulnerability by sending a crafted SSL/TLS message through an affected device. SSL/TLS messages sent to an affected device do not trigger this vulnerability. A successful exploit could allow the attacker to cause a process to crash. This crash would then trigger a reload of the device. No manual intervention is needed to recover the device after the reload.

Multiple vulnerabilities in Cisco SD-WAN products could allow an unauthenticated, remote attacker to execute denial of service (DoS) attacks against an affected device. For more information about these vulnerabilities, see the Details section of this advisory.

Multiple vulnerabilities in Cisco SD-WAN products could allow an unauthenticated, remote attacker to execute denial of service (DoS) attacks against an affected device. For more information about these vulnerabilities, see the Details section of this advisory.

Multiple vulnerabilities in Cisco SD-WAN products could allow an unauthenticated, remote attacker to execute denial of service (DoS) attacks against an affected device. For more information about these vulnerabilities, see the Details section of this advisory.

Multiple vulnerabilities in Cisco SD-WAN products could allow an unauthenticated, remote attacker to execute denial of service (DoS) attacks against an affected device. For more information about these vulnerabilities, see the Details section of this advisory.

Multiple vulnerabilities in Cisco SD-WAN vEdge Software could allow an attacker to execute arbitrary code as the root user or cause a denial of service (DoS) condition on an affected device. For more information about these vulnerabilities, see the Details section of this advisory.

A vulnerability in the SSL/TLS inspection of Cisco Firepower Threat Defense (FTD) Software for Cisco Firepower 2100 Series firewalls could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to improper input validation for certain fields of specific SSL/TLS messages. An attacker could exploit this vulnerability by sending a malformed SSL/TLS message through an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. No manual intervention is needed to recover the device after it has reloaded.

A vulnerability in the IPv6 implementation of Cisco StarOS could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to insufficient validation of incoming IPv6 traffic. An attacker could exploit this vulnerability by sending a crafted IPv6 packet to an affected device with the goal of reaching the vulnerable section of the input buffer. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition. This vulnerability is specific to IPv6 traffic. IPv4 traffic is not affected.

A vulnerability in the Secure Sockets Layer (SSL)/Transport Layer Security (TLS) handler of Cisco Firepower Threat Defense (FTD) Software when running on the Cisco Firepower 1000 Series platform could allow an unauthenticated, remote attacker to trigger a denial of service (DoS) condition on an affected device. The vulnerability is due to a communication error between internal functions. An attacker could exploit this vulnerability by sending a crafted SSL/TLS message to an affected device. A successful exploit could allow the attacker to cause a buffer underrun, which leads to a crash. The crash causes the affected device to reload.

A vulnerability in the 802.11 Generic Advertisement Service (GAS) frame processing function of Cisco Wireless LAN Controller (WLC) Software could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS). The vulnerability is due to incomplete input validation of the 802.11 GAS frames that are processed by an affected device. An attacker could exploit this vulnerability by sending a crafted 802.11 GAS frame over the air to an access point (AP), and that frame would then be relayed to the affected WLC. Also, an attacker with Layer 3 connectivity to the WLC could exploit this vulnerability by sending a malicious 802.11 GAS payload in a Control and Provisioning of Wireless Access Points (CAPWAP) packet to the device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS.

A vulnerability in the FTP inspection engine of Cisco Adaptive Security (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to insufficient validation of FTP data. An attacker could exploit this vulnerability by sending malicious FTP traffic through an affected device. A successful exploit could allow the attacker to cause a DoS condition on the affected device.

A vulnerability in the Layer 3 multicast feature of Cisco IOS XR Software for Cisco ASR 9000 Series Aggregation Services Routers, ASR 9902 Compact High-Performance Routers, and ASR 9903 Compact High-Performance Routers could allow an unauthenticated, remote attacker to cause a line card to reset, resulting in a denial of service (DoS) condition. This vulnerability is due to the incorrect handling of malformed IPv4 multicast packets that are received on line cards where the interface has either an IPv4 access control list (ACL) or a QoS policy applied. An attacker could exploit this vulnerability by sending crafted IPv4 multicast packets through an affected device. A successful exploit could allow the attacker to cause line card exceptions or a hard reset. Traffic over that line card would be lost while the line card reloads.

A vulnerability in the RADIUS proxy feature for the IPsec VPN feature of Cisco Secure Firewall Adaptive Security Appliance (ASA) Software and Cisco Secure Firewall Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition. This vulnerability is due to improper processing of IPv6 packets. An attacker could exploit this vulnerability by sending IPv6 packets over an IPsec VPN connection to an affected device. A successful exploit could allow the attacker to trigger a reload of the device, resulting in a DoS condition.

A vulnerability in the function that performs IPv4 and IPv6 Network Address Translation (NAT) DNS inspection for Cisco Secure Firewall Adaptive Security Appliance (ASA) Software and Cisco Secure Firewall Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause the device to reload unexpectedly, resulting in a denial of service (DoS) condition.  This vulnerability is due to an infinite loop condition that occurs when a Cisco Secure ASA or Cisco Secure FTD device processes DNS packets with DNS inspection enabled and the device is configured for NAT44, NAT64, or NAT46. An attacker could exploit this vulnerability by sending crafted DNS packets that match a static NAT rule with DNS inspection enabled through an affected device. A successful exploit could allow the attacker to create an infinite loop and cause the device to reload, resulting in a DoS condition.

A vulnerability in chat messaging features of Cisco Enterprise Chat and Email (ECE) could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition. This vulnerability is due to improper validation of user-supplied input to chat entry points. An attacker could exploit this vulnerability by sending malicious requests to a messaging chat entry point in the affected application. A successful exploit could allow the attacker to cause the application to stop responding, resulting in a DoS condition. The application may not recover on its own and may need an administrator to manually restart services to recover.

A vulnerability in the web UI of Cisco Desk Phone 9800 Series, Cisco IP Phone 7800 and 8800 Series, and Cisco Video Phone 8875 running Cisco SIP Software could allow an unauthenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to a buffer overflow when an affected device processes HTTP packets. An attacker could exploit this vulnerability by sending crafted HTTP input to the device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition. Note: To exploit this vulnerability, the phone must be registered to Cisco Unified Communications Manager and have Web Access enabled. Web Access is disabled by default.

A vulnerability in the management and VPN web servers of Cisco Secure Firewall ASA Software and Secure FTD Software could allow an unauthenticated, remote attacker to cause the device to reload unexpectedly, resulting in a DoS condition. This vulnerability is due to improper validation of user-supplied input on an interface with VPN web services. An attacker could exploit this vulnerability by sending crafted HTTP requests to a targeted web server on an affected device. A successful exploit could allow the attacker to cause a DoS condition when the device reloads.

A vulnerability in the RADIUS setting Reject RADIUS requests from clients with repeated failures on Cisco Identity Services Engine (ISE) could allow an unauthenticated, remote attacker to cause Cisco ISE to restart unexpectedly. This vulnerability is due to a logic error when processing a RADIUS access request for a MAC address that is already a rejected endpoint. An attacker could exploit this vulnerability by sending a specific sequence of multiple crafted RADIUS access request messages to Cisco ISE. A successful exploit could allow the attacker to cause a denial of service (DoS) condition when Cisco ISE restarts.

A vulnerability in the DHCP snooping security feature of Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a full interface queue wedge, which could result in a denial of service (DoS) condition. This vulnerability is due to improper handling of DHCP request packets. An attacker could exploit this vulnerability by sending DHCP request packets to an affected device. A successful exploit could allow the attacker to cause packets to wedge in the queue, creating a DoS condition for downstream devices of the affected system and requiring that the system restart to drain the queue. Note: This vulnerability can be exploited with either unicast or broadcast DHCP packets on a VLAN that does not have DHCP snooping enabled.

A vulnerability in the certificate processing of Cisco Secure Firewall Adaptive Security Appliance (ASA) Software and Cisco Secure Firewall Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause the device to reload unexpectedly, resulting in a denial of service (DoS) condition. This vulnerability is due to improper parsing of SSL/TLS certificates. An attacker could exploit this vulnerability by sending crafted DNS packets that match a static Network Address Translation (NAT) rule with DNS inspection enabled through an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.

A vulnerability in the IPv4 access control list (ACL) feature and quality of service (QoS) policy feature of Cisco IOS XR Software for Cisco ASR 9000 Series Aggregation Services Routers, ASR 9902 Compact High-Performance Routers, and ASR 9903 Compact High-Performance Routers could allow an unauthenticated, remote attacker to cause a line card to reset, resulting in a denial of service (DoS) condition. This vulnerability is due to the incorrect handling of malformed IPv4 packets that are received on line cards where the interface has either an IPv4 ACL or QoS policy applied. An attacker could exploit this vulnerability by sending crafted IPv4 packets through an affected device. A successful exploit could allow the attacker to cause network processor errors, resulting in a reset or shutdown of the network process. Traffic over that line card would be lost while the line card reloads. Note: This vulnerability has predominantly been observed in Layer 2 VPN (L2VPN) environments where an IPv4 ACL or QoS policy has been applied to the bridge virtual interface. Layer 3 configurations where the interface has either an IPv4 ACL or QoS policy applied are also affected, though the vulnerability has not been observed.

A vulnerability in the Internet Key Exchange version 2 (IKEv2) protocol processing of Cisco Adaptive Security Appliance (ASA) Software, Cisco Firepower Threat Defense (FTD) Software, Cisco IOS Software, and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient input validation when processing IKEv2 messages. An attacker could exploit this vulnerability by sending crafted IKEv2 traffic to an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition on the affected device.

A vulnerability in the management and VPN web servers of the Remote Access SSL VPN feature of Cisco Secure Firewall ASA Software and Secure FTD Software could allow an unauthenticated, remote attacker to cause the device to unexpectedly stop responding, resulting in a DoS condition. This vulnerability is due to ineffective validation of user-supplied input during the Remote Access SSL VPN authentication process. An attacker could exploit this vulnerability by sending a crafted request to the VPN service on an affected device. A successful exploit could allow the attacker to cause a DoS condition where the device stops responding to Remote Access SSL VPN authentication requests.

A vulnerability in the SIP processing subsystem of Cisco BroadWorks could allow an unauthenticated, remote attacker to halt the processing of incoming SIP requests, resulting in a denial of service (DoS) condition. This vulnerability is due to improper memory handling for certain SIP requests. An attacker could exploit this vulnerability by sending a high number of SIP requests to an affected system. A successful exploit could allow the attacker to exhaust the memory that was allocated to the Cisco BroadWorks Network Servers that handle SIP traffic. If no memory is available, the Network Servers can no longer process incoming requests, resulting in a DoS condition that requires manual intervention to recover.

A vulnerability in the Object Linking and Embedding 2 (OLE2) decryption routine of ClamAV could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to an integer underflow in a bounds check that allows for a heap buffer overflow read. An attacker could exploit this vulnerability by submitting a crafted file containing OLE2 content to be scanned by ClamAV on an affected device. A successful exploit could allow the attacker to terminate the ClamAV scanning process, resulting in a DoS condition on the affected software. For a description of this vulnerability, see the . Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability.

A vulnerability in the Cisco AnyConnect VPN server of Cisco Meraki MX and Cisco Meraki Z Series Teleworker Gateway devices could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition in the Cisco AnyConnect service on an affected device. This vulnerability is due to variable initialization errors when an SSL VPN session is established. An attacker could exploit this vulnerability by sending a sequence of crafted HTTPS requests to an affected device. A successful exploit could allow the attacker to cause the Cisco AnyConnect VPN server to restart, resulting in the failure of all established SSL VPN sessions and forcing remote users to initiate a new VPN connection and re-authenticate. A sustained attack could prevent new SSL VPN connections from being established, effectively making the Cisco AnyConnect VPN service unavailable for all legitimate users.

A vulnerability in the web services interface of Cisco Secure Firewall Adaptive Security Appliance (ASA) Software and Cisco Secure Firewall Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a buffer overflow on an affected system.  This vulnerability is due to insufficient boundary checks for specific data that is provided to the web services interface of an affected system. An attacker could exploit this vulnerability by sending a crafted HTTP request to the affected system. A successful exploit could allow the attacker to cause a buffer overflow condition on the affected system, which could cause the system to reload, resulting in a denial of service (DoS) condition.

A vulnerability in the packet inspection functionality of the Snort 3 Detection Engine of Cisco Secure Firewall Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to incorrect processing of traffic that is inspected by an affected device. An attacker could exploit this vulnerability by sending crafted traffic through the affected device. A successful exploit could allow the attacker to cause the affected device to enter an infinite loop while inspecting traffic, resulting in a DoS condition. The system watchdog will restart the Snort process automatically.

A vulnerability in the IKEv2 feature of Cisco IOS Software, IOS XE Software, Secure Firewall ASA Software, and Secure FTD Software could allow an unauthenticated, remote attacker to cause the device to reload, resulting in a DoS condition. This vulnerability is due to the improper processing of IKEv2 packets. An attacker could exploit this vulnerability by sending crafted IKEv2 packets to an affected device. A successful exploit could allow the attacker to cause an infinite loop that exhausts resources and could cause the device to reload.

A vulnerability in confederation implementation for the Border Gateway Protocol (BGP) in Cisco IOS XR Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition. This vulnerability is due to a memory corruption that occurs when a BGP update is created with an AS_CONFED_SEQUENCE attribute that has 255 autonomous system numbers (AS numbers). An attacker could exploit this vulnerability by sending a crafted BGP update message, or the network could be designed in such a manner that the AS_CONFED_SEQUENCE attribute grows to 255 AS numbers or more. A successful exploit could allow the attacker to cause memory corruption, which may cause the BGP process to restart, resulting in a DoS condition. To exploit this vulnerability, an attacker must control a BGP confederation speaker within the same autonomous system as the victim, or the network must be designed in such a manner that the AS_CONFED_SEQUENCE attribute grows to 255 AS numbers or more.

A vulnerability in the Internet Key Exchange Version 2 (IKEv2) feature of Cisco IOS Software, IOS XE Software, Secure Firewall Adaptive Security Appliance (ASA) Software, and Secure Firewall Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to trigger a memory leak, resulting in a denial of service (DoS) condition. This vulnerability is due to a lack of proper processing of IKEv2 packets. An attacker could exploit this vulnerability by sending crafted IKEv2 packets to an affected device. In the case of Cisco IOS and IOS XE Software, a successful exploit could allow the attacker to cause the device to reload unexpectedly. In the case of Cisco ASA and FTD Software, a successful exploit could allow the attacker to partially exhaust system memory, causing system instability such as being unable to establish new IKEv2 VPN sessions. A manual reboot of the device is required to recover from this condition.

A vulnerability in the RADIUS message processing feature of Cisco Identity Services Engine (ISE) could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to improper handling of certain RADIUS requests. An attacker could exploit this vulnerability by sending a specific authentication request to a network access device (NAD) that uses Cisco ISE for authentication, authorization, and accounting (AAA). A successful exploit could allow the attacker to cause Cisco ISE to reload.

A vulnerability in the system resource management of Cisco Elastic Services Controller (ESC) could allow an unauthenticated, remote attacker to cause a denial of service (DoS) to the health monitor API on an affected device. The vulnerability is due to inadequate provisioning of kernel parameters for the maximum number of TCP connections and SYN backlog. An attacker could exploit this vulnerability by sending a flood of crafted TCP packets to an affected device. A successful exploit could allow the attacker to block TCP listening ports that are used by the health monitor API. This vulnerability only affects customers who use the health monitor API.

A vulnerability in the Two-Way Active Measurement Protocol (TWAMP) server feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause the affected device to reload, resulting in a denial of service (DoS) condition. For Cisco IOS XR Software, this vulnerability could cause the ipsla_ippm_server process to reload unexpectedly if debugs are enabled. This vulnerability is due to out-of-bounds array access when processing specially crafted TWAMP control packets. An attacker could exploit this vulnerability by sending crafted TWAMP control packets to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Note: For Cisco IOS XR Software, only the ipsla_ippm_server process reloads unexpectedly and only when debugs are enabled. The vulnerability details for Cisco IOS XR Software are as follows:    Security Impact Rating (SIR): Low    CVSS Base Score: 3.7    CVSS Vector: CVSS:3.1/AV:N/AC:H/PR:N/UI:N/S:U/C:N/I:N/A:L

The IKEv1 implementation in Cisco IOS 12.2 through 12.4 and 15.0 through 15.2 and IOS XE 2.1.x through 2.6.x and 3.1.xS through 3.4.xS before 3.4.2S, 3.5.xS before 3.5.1S, and 3.2.xSG before 3.2.2SG allows remote attackers to cause a denial of service (device reload) by sending IKE UDP packets over (1) IPv4 or (2) IPv6, aka Bug ID CSCts38429.

A vulnerability in the Internet Key Exchange Version 2 (IKEv2) module of Cisco IOS 15.0 through 15.6 and Cisco IOS XE 3.5 through 16.5 could allow an unauthenticated, remote attacker to cause high CPU utilization, traceback messages, or a reload of an affected device that leads to a denial of service (DoS) condition. The vulnerability is due to how an affected device processes certain IKEv2 packets. An attacker could exploit this vulnerability by sending specific IKEv2 packets to an affected device to be processed. A successful exploit could allow the attacker to cause high CPU utilization, traceback messages, or a reload of the affected device that leads to a DoS condition. This vulnerability affects Cisco devices that have the Internet Security Association and Key Management Protocol (ISAKMP) enabled. Although only IKEv2 packets can be used to trigger this vulnerability, devices that are running Cisco IOS Software or Cisco IOS XE Software are vulnerable when ISAKMP is enabled. A device does not need to be configured with any IKEv2-specific features to be vulnerable. Many features use IKEv2, including different types of VPNs such as the following: LAN-to-LAN VPN; Remote-access VPN, excluding SSL VPN; Dynamic Multipoint VPN (DMVPN); and FlexVPN. Cisco Bug IDs: CSCvc41277.

A vulnerability in the implementation of the PROFINET Discovery and Configuration Protocol (PN-DCP) for Cisco IOS 12.2 through 15.6 could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability is due to the improper parsing of ingress PN-DCP Identify Request packets destined to an affected device. An attacker could exploit this vulnerability by sending a crafted PN-DCP Identify Request packet to an affected device and then continuing to send normal PN-DCP Identify Request packets to the device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. This vulnerability affects Cisco devices that are configured to process PROFINET messages. Beginning with Cisco IOS Software Release 12.2(52)SE, PROFINET is enabled by default on all the base switch module and expansion-unit Ethernet ports. Cisco Bug IDs: CSCuz47179.

Multiple vulnerabilities in the implementation of the Common Industrial Protocol (CIP) feature in Cisco IOS 12.4 through 15.6 could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerabilities are due to the improper parsing of crafted CIP packets destined to an affected device. An attacker could exploit these vulnerabilities by sending crafted CIP packets to be processed by an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Cisco Bug IDs: CSCvc43709.

A memory leak vulnerability exists in Cisco IOS before 15.2(1)T due to a memory leak in the HTTP PROXY Server process (aka CSCtu52820), when configured with Cisco ISR Web Security with Cisco ScanSafe and User Authenticaiton NTLM configured.

Multiple vulnerabilities in the implementation of the Common Industrial Protocol (CIP) feature in Cisco IOS 12.4 through 15.6 could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerabilities are due to the improper parsing of crafted CIP packets destined to an affected device. An attacker could exploit these vulnerabilities by sending crafted CIP packets to be processed by an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Cisco Bug IDs: CSCuz95334.