A flaw was found in libsoup. The libsoup soup_uri_decode_data_uri() function may crash when processing malformed data URI. This flaw allows an attacker to cause a denial of service (DoS).

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on MX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS).When processing a high rate of specific GRE traffic destined to the device, the respective PFE will hang causing traffic forwarding to stop. When this issue occurs the following logs can be observed: <fpc #> MQSS(0): LI-3: Received a parcel with more than 512B accompanying data CHASSISD_FPC_ASIC_ERROR: ASIC Error detected <...> This issue affects Junos OS: * all versions before 21.2R3-S9, * 21.4 versions before 21.4R3-S8, * 22.2 versions before 22.2R3-S4, * 22.4 versions before 22.4R3-S5, * 23.2 versions before 23.2R2-S2, * 23.4 versions before 23.4R2.

NamelessMC is a free, easy to use & powerful website software for Minecraft servers. In version 2.1.4 and prior, the s parameter in GET requests for forum search functionality lacks length validation, allowing attackers to submit excessively long search queries. This oversight can lead to performance degradation and potential denial-of-service (DoS) attacks. This issue has been patched in version 2.2.0.

A Denial of Service vulnerability related to command handling has been identified in FlexNet Publisher lmadmin.exe version 11.16.2. The message reading function used in lmadmin.exe can, given a certain message, call itself again and then wait for a further message. With a particular flag set in the original message, but no second message received, the function eventually return an unexpected value which leads to an exception being thrown. The end result can be process termination.

Denial-of-service (DoS) vulnerability due to improper validation of specified type of input issue exists in the built-in EtherNet/IP port of the CJ Series CJ2 CPU unit and the communication function of the CS/CJ Series EtherNet/IP unit. If an affected product receives a packet which is specially crafted by a remote unauthenticated attacker, the unit of the affected product may fall into a denial-of-service (DoS) condition. Affected products/versions are as follows: CJ2M CPU Unit CJ2M-CPU3[] Unit version of the built-in EtherNet/IP section Ver. 2.18 and earlier, CJ2H CPU Unit CJ2H-CPU6[]-EIP Unit version of the built-in EtherNet/IP section Ver. 3.04 and earlier, CS/CJ Series EtherNet/IP Unit CS1W-EIP21 V3.04 and earlier, and CS/CJ Series EtherNet/IP Unit CJ1W-EIP21 V3.04 and earlier.

A CWE-754: Improper Check for Unusual or Exceptional Conditions vulnerability exists which could cause a possible Denial of Service when specific Modbus frames are sent to the controller in the products: Modicon M340 - firmware versions prior to V3.01, Modicon M580 - firmware versions prior to V2.80, All firmware versions of Modicon Quantum and Modicon Premium.

A CWE-754: Improper Check for Unusual or Exceptional Conditions vulnerability exists in Modicon M580, Modicon M340, Modicon Quantum, Modicon Premium (see security notification for specific versions) which could cause a Denial of Service when writing specific physical memory blocks using Modbus TCP.

A CWE-754: Improper Check for Unusual or Exceptional Conditions vulnerability exists in Modicon M580, Modicon M340, Modicon Quantum, Modicon Premium (see security notification for specific versions) which could cause a Denial of Service of the controller when reading specific memory blocks using Modbus TCP.

An Improper Check or Handling of Exceptional Conditions within the storm control feature of Juniper Networks Junos OS allows an attacker sending a high rate of traffic to cause a Denial of Service. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. Storm control monitors the level of applicable incoming traffic and compares it with the level specified. If the combined level of the applicable traffic exceeds the specified level, the switch drops packets for the controlled traffic types. This issue affects Juniper Networks Junos OS on QFX10002: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2.

OpenVPN version 2.6.1 through 2.6.13 in server mode using TLS-crypt-v2 allows remote attackers to trigger a denial of service by corrupting and replaying network packets in the early handshake phase

Feathersjs is a framework for creating web APIs and real-time applications with TypeScript or JavaScript. Feathers socket handler did not catch invalid string conversion errors like `const message = ${{ toString: '' }}` which would cause the NodeJS process to crash when sending an unexpected Socket.io message like `socket.emit('find', { toString: '' })`. A fix has been released in versions 5.0.8 and 4.5.18. Users are advised to upgrade. There is no known workaround for this vulnerability.

An issue was discovered in ide_dma_cb() in hw/ide/core.c in QEMU 2.4.0 through 4.2.0. The guest system can crash the QEMU process in the host system via a special SCSI_IOCTL_SEND_COMMAND. It hits an assertion that implies that the size of successful DMA transfers there must be a multiple of 512 (the size of a sector). NOTE: a member of the QEMU security team disputes the significance of this issue because a "privileged guest user has many ways to cause similar DoS effect, without triggering this assert.

lettersanitizer is a DOM-based HTML email sanitizer for in-browser email rendering. All versions of lettersanitizer below 1.0.2 are affected by a denial of service issue when processing a CSS at-rule `@keyframes`. This package is depended on by [react-letter](https://github.com/mat-sz/react-letter), therefore everyone using react-letter is also at risk. The problem has been patched in version 1.0.2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on QFX10000 Series allows a network based attacker to cause a Denial of Service (DoS). If a specific valid IP packet is received and that packet needs to be routed over a VXLAN tunnel, this will result in a PFE wedge condition due to which traffic gets impacted. As this is not a crash and restart scenario, this condition will persist until the system is rebooted to recover. This issue affects Juniper Networks Junos OS on QFX10000: 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S5; 21.3 versions prior to 21.3R3-S4; 21.4 versions prior to 21.4R3-S1; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2; 22.3 versions prior to 22.3R1-S2, 22.3R2.

The issue was addressed with improved checks. This issue is fixed in tvOS 18.5, iOS 18.5 and iPadOS 18.5, iPadOS 17.7.9, macOS Sequoia 15.5, watchOS 11.5, visionOS 2.5, macOS Ventura 13.7.7. A remote attacker may be able to cause unexpected system termination.

AVEVA PI Server versions 2023 and 2018 SP3 P05 and prior contain a vulnerability that could allow an unauthenticated user to remotely crash the PI Message Subsystem of a PI Server, resulting in a denial-of-service condition.

The HTTP server in Mongoose before 7.10 accepts requests containing negative Content-Length headers. By sending a single attack payload over TCP, an attacker can cause an infinite loop in which the server continuously reparses that payload, and does not respond to any other requests.

In network HW, there is a possible system hang due to an uncaught exception. This could lead to remote denial of service with no additional execution privileges needed. User interaction is not needed for exploitation. Patch ID: WCNCR00399035; Issue ID: MSV-2380.

socket.io parser is a socket.io encoder and decoder written in JavaScript complying with version 5 of socket.io-protocol. A specially crafted Socket.IO packet can trigger an uncaught exception on the Socket.IO server, thus killing the Node.js process. A patch has been released in version 4.2.3.

A vulnerability exists in the HCI Modbus TCP function included in the product versions listed above. If the HCI Modbus TCP is en-abled and configured, an attacker could exploit the vulnerability by sending a specially crafted message to the RTU500, causing the receiving RTU500 CMU to reboot. The vulnerability is caused by the validation error in the length information carried in MBAP header in the HCI Modbus TCP function.

An unauthenticated remote attacker can causes the CODESYS web server to access invalid memory which results in a DoS.

Denial-of-service in NodeBB <= v2.8.10 allows unauthenticated attackers to trigger a crash, when invoking `eventName.startsWith()` or `eventName.toString()`, while processing Socket.IO messages via crafted Socket.IO messages containing array or object type for the event name respectively.

Improper Validation of Specified Quantity in Input vulnerability in Mitsubishi Electric CNC Series allows a remote unauthenticated attacker to cause Denial of Service (DoS) condition on the product by sending specially crafted packets to TCP port 683, causing an emergency stop.

Out-of-bounds read vulnerability in the M3U8 module Impact: Successful exploitation of this vulnerability may cause features to perform abnormally.

DaveGamble/cJSON cJSON 1.7.8 is affected by: Improper Check for Unusual or Exceptional Conditions. The impact is: Null dereference, so attack can cause denial of service. The component is: cJSON_GetObjectItemCaseSensitive() function. The attack vector is: crafted json file. The fixed version is: 1.7.9 and later.

The SRX flowd process, responsible for packet forwarding, may crash and restart when processing specific multicast packets. By continuously sending the specific multicast packets, an attacker can repeatedly crash the flowd process causing a sustained Denial of Service. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D90; 15.1X49 versions prior to 15.1X49-D180; 17.3 versions; 17.4 versions prior to 17.4R2-S5, 17.4R3; 18.1 versions prior to 18.1R3-S6; 18.2 versions prior to 18.2R2-S4, 18.2R3; 18.3 versions prior to 18.3R2-S1, 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S1, 19.1R2.

Florent Thiéry has found that selected Axis devices were vulnerable to handling certain ethernet frames which could lead to the Axis device becoming unavailable in the network. Axis has released patched AXIS OS versions for the highlighted flaw for products that are still under AXIS OS software support. Please refer to the Axis security advisory for more information and solution.

An unauthenticated user can overload a part of HCL VersionVault Express and cause a denial of service.

An Improper Check for Unusual or Exceptional Conditions vulnerability exists in Schneider Electric's Modicon M221 product (all references, all versions prior to firmware V1.6.2.0). The vulnerability allows unauthorized users to remotely reboot Modicon M221 using crafted programing protocol frames.

A CWE-754: Improper Check for Unusual or Exceptional Conditions vulnerability exists in Modicon M580, Modicon M340, Modicon Quantum, Modicon Premium (see security notification for specific versions) which could cause a Denial of Service when reading data with invalid index using Modbus TCP.

A CWE-248: Uncaught Exception vulnerability exists in all versions of the Modicon M580, Modicon M340, Modicon Quantum, and Modicon Premium which could cause a possible Denial of Service when writing out of bounds variables to the controller over Modbus.

A CWE-248: Uncaught Exception vulnerability exists in all versions of the Modicon M580, Modicon M340, Modicon Quantum, and Modicon Premium which could cause denial of service when reading invalid physical memory blocks in the controller over Modbus

A CWE-248 Uncaught Exception vulnerability exists in all versions of the Modicon M580, Modicon M340, Modicon Quantum, and Modicon Premium which could cause a Denial of Service when sending invalid breakpoint parameters to the controller over Modbus

Gallagher Controller 6000 is vulnerable to a Denial of Service attack via conflicting ARP packets with a duplicate IP address. This issue affects: Gallagher Gallagher Controller 6000 vCR8.60 versions prior to 220303a; vCR8.50 versions prior to 220303a; vCR8.40 versions prior to 220303a; vCR8.30 versions prior to 220303a.

A CWE-248: Uncaught Exception vulnerability exists in all versions of the Modicon M580, Modicon M340, Modicon Quantum, and Modicon Premium which could cause a possible denial of Service when writing invalid memory blocks to the controller over Modbus.

IBM WebSphere Application Server 8.5 is vulnerable to a denial of service, under certain configurations, caused by an unexpected specially crafted request. A remote attacker could exploit this vulnerability to cause an error resulting in a denial of service.

An issue was discovered in Django 5.0 before 5.0.8 and 4.2 before 4.2.15. The urlize and urlizetrunc template filters, and the AdminURLFieldWidget widget, are subject to a potential denial-of-service attack via certain inputs with a very large number of Unicode characters.

On SRX Series devices, an Improper Check for Unusual or Exceptional Conditions when using Certificate Management Protocol Version 2 (CMPv2) auto re-enrollment, allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS) by crashing the pkid process. The pkid process cannot handle an unexpected response from the Certificate Authority (CA) server, leading to crash. A restart is required to restore services. This issue affects: Juniper Networks Junos OS on SRX Series: All versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S1; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R2.

A vulnerability in Juniper Networks Junos OS on SRX Series, allows a network-based unauthenticated attacker to cause a Denial of Service (DoS) by sending a specific fragmented packet to the device, resulting in a flowd process crash, which is responsible for packet forwarding. Continued receipt and processing of this specific packet will create a sustained DoS condition. This issue only affects SRX Series when 'preserve-incoming-fragment-size' feature is enabled. This issue affects Juniper Networks Junos OS on SRX Series: 18.3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R3-S10; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R2. This issue does not affect Juniper Networks Junos OS prior to 17.3R1.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated networked attacker to cause a Denial of Service (DoS) by sending specific packets over VXLAN which cause the PFE to reset. This issue affects: Juniper Networks Junos OS 19.4 versions prior to 19.4R3-S7; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S1; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R2; 21.3 versions prior to 21.3R1-S1, 21.3R2. This issue does not affect versions of Junos OS prior to 19.4R1.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the packetIO daemon of Juniper Networks Junos OS Evolved on PTX10003, PTX10004, and PTX10008 allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). Continued receipt of these crafted packets will cause a sustained Denial of Service condition. This issue affects Juniper Networks Junos OS Evolved all versions prior to 20.4R2-S3-EVO on PTX10003, PTX10004, and PTX10008. This issue does not affect: Juniper Networks Junos OS Evolved versions 21.1R1-EVO and above; Juniper Networks Junos OS.

Parse Server is an open source backend that can be deployed to any infrastructure that can run Node.js. Versions prior to 4.10.17, and prior to 5.2.8 on the 5.x branch, crash when a file download request is received with an invalid byte range, resulting in a Denial of Service. This issue has been patched in versions 4.10.17, and 5.2.8. There are no known workarounds.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based, attacker to cause Denial of Service (DoS). A PFE crash will happen when a GPRS Tunnel Protocol (GTP) packet is received with a malformed field in the IP header of GTP encapsulated General Packet Radio Services (GPRS) traffic. The packet needs to match existing state which is outside the attackers control, so the issue cannot be directly exploited. The issue will only be observed when endpoint address validation is enabled. This issue affects Juniper Networks Junos OS on SRX Series: 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2; 22.1 versions prior to 22.1R1-S1, 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.2R1.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the processing of specific IPv6 packets on certain EX Series devices may lead to exhaustion of DMA memory causing a Denial of Service (DoS). Over time, exploitation of this vulnerability may cause traffic to stop being forwarded, or a crash of the fxpc process. An indication of the issue occurring may be observed through the following log messages: Sep 13 17:14:59 hostname : %PFE-3: fpc0 (buf alloc) failed allocating packet buffer Sep 13 17:14:59 hostname : %PFE-7: fpc0 brcm_pkt_buf_alloc:393 (buf alloc) failed allocating packet buffer When Packet DMA heap utilization reaches 99%, the system will become unstable. Packet DMA heap utilization can be monitored using the command: user@junos# request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 213301a8 536870488 387228840 149641648 27 Kernel 1 91800000 8388608 3735120 4653488 55 DMA 2 92000000 75497472 74452192 1045280 1 PKT DMA DESC 3 d330000 335544320 257091400 78452920 23 Bcm_sdk 4 96800000 184549376 2408 184546968 99 Packet DMA <<<< 5 903fffe0 20971504 20971504 0 0 Blob This issue affects: Juniper Networks Junos OS 18.4 versions prior to 18.4R2-S10, 18.4R3-S10 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.1 versions prior to 19.1R3-S7 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.3 versions prior to 19.3R3-S5 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.4 versions prior to 19.4R3-S7 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.1 versions prior to 20.1R3-S3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.2 versions prior to 20.2R3-S3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.3 versions prior to 20.3R3-S2 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.4 versions prior to 20.4R3-S1 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.1 versions prior to 21.1R2-S2, 21.1R3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.2 versions prior to 21.2R1-S2, 21.2R2 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.3 versions prior to 21.3R1-S1, 21.3R2 on EX2300 Series, EX2300-MP Series, EX3400 Series.

The package node-opcua before 2.74.0 are vulnerable to Denial of Service (DoS) due to a missing limitation on the number of received chunks - per single session or in total for all concurrent sessions. An attacker can exploit this vulnerability by sending an unlimited number of huge chunks (e.g. 2GB each) without sending the Final closing chunk.

The Custom Popup Builder WordPress plugin before 1.3.1 autoload data from its popup on every pages, as such data can be sent by unauthenticated user, and is not validated in length, this could cause a denial of service on the blog

NHI’s health insurance web service component has insufficient validation for input string length, which can result in heap-based buffer overflow attack. A remote attacker can exploit this vulnerability to flood the memory space reserved for the program, in order to terminate service without authentication, which requires a system restart to recover service.

In Open5GS 2.4.0, a crafted packet from UE can crash SGW-U/UPF.

Istio is an open platform to connect, manage, and secure microservices. In affected versions the Istio control plane, `istiod`, is vulnerable to a request processing error, allowing a malicious attacker that sends a specially crafted message which results in the control plane crashing. This endpoint is served over TLS port 15012, but does not require any authentication from the attacker. For simple installations, Istiod is typically only reachable from within the cluster, limiting the blast radius. However, for some deployments, especially [multicluster](https://istio.io/latest/docs/setup/install/multicluster/primary-remote/) topologies, this port is exposed over the public internet. There are no effective workarounds, beyond upgrading. Limiting network access to Istiod to the minimal set of clients can help lessen the scope of the vulnerability to some extent.