A Missing Release of Memory after Effective Lifetime vulnerability in the routing protocol daemon of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network based attacker to cause a Denial of Service (DoS). In a BGP rib sharding scenario, when an attribute of an active BGP route is updated memory will leak. As rpd memory usage increases over time the rpd process will eventually run out of memory, crash, and restart. The memory utilization can be monitored with the following CLI commands: show task memory show system processes extensive | match rpd This issue affects: Juniper Networks Junos OS 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2. Juniper Networks Junos OS Evolved 20.3-EVO version 20.3R1-EVO and later versions; 20.4-EVO versions prior to 20.4R3-S6-EVO; 21.2-EVO versions prior to 21.2R3-EVO; 21.3-EVO versions prior to 21.3R2-EVO.

An Improper Validation of Syntactic Correctness of Input vulnerability in Intrusion Detection and Prevention (IDP) of Juniper Networks SRX Series and MX Series allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). Continued receipt of this specific packet will cause a sustained Denial of Service condition. On all SRX Series and MX Series platforms, where IDP is enabled and a specific malformed SSL packet is received, the SSL detector crashes leading to an FPC core. This issue affects Juniper Networks SRX Series and MX Series prior to SigPack 3598. In order to identify the current SigPack version, following command can be used: user@junos# show security idp security-package-version

An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (pfe) of Juniper Networks Junos OS on MX Series allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). If specific traffic is received on MX Series and its rate exceeds the respective DDoS protection limit the ingress PFE will crash and restart. Continued receipt of this traffic will create a sustained DoS condition. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S5; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2.

A Use of Uninitialized Resource vulnerability in the Border Gateway Protocol (BGP) software of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker to send specific genuine BGP packets to a device configured with BGP to cause a Denial of Service (DoS) by crashing the Routing Protocol Daemon (rpd). This issue is triggered when the packets attempt to initiate a BGP connection before a BGP session is successfully established. Continued receipt of these specific BGP packets will cause a sustained Denial of Service condition. This issue is triggerable in both iBGP and eBGP deployments. This issue affects: Juniper Networks Junos OS 21.1 version 21.1R1 and later versions prior to 21.1R3-S5; 21.2 version 21.2R1 and later versions prior to 21.2R3-S2; 21.3 version 21.3R1 and later versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 21.1R1. This issue affects: Juniper Networks Junos OS Evolved 21.1-EVO version 21.1R1-EVO and later versions prior to 21.4R3-EVO; 22.1-EVO versions prior to 22.1R3-EVO; 22.2-EVO versions prior to 22.2R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 21.1R1-EVO.

An Improper Check or Handling of Exceptional Conditions vulnerability in the IPsec library of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause Denial of Service (DoS). On all MX platforms with MS-MPC or MS-MIC card, when specific IPv4 packets are processed by an IPsec6 tunnel, the Multiservices PIC Management Daemon (mspmand) process will core and restart. This will lead to FPC crash. Traffic flow is impacted while mspmand restarts. Continued receipt of these specific packets will cause a sustained Denial of Service (DoS) condition. This issue only occurs if an IPv4 address is not configured on the multiservice interface. This issue affects: Juniper Networks Junos OS on MX Series All versions prior to 19.4R3-S9; 20.1 version 20.1R3-S5 and later versions; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R2.

An Improper Validation of Array Index vulnerability in the SIP ALG of Juniper Networks Junos OS on SRX 5000 Series allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). When an attacker sends an SIP packets with a malformed SDP field then the SIP ALG can not process it which will lead to an FPC crash and restart. Continued receipt of these specific packets will lead to a sustained Denial of Service. This issue can only occur when both below mentioned conditions are fulfilled: 1. Call distribution needs to be enabled: [security alg sip enable-call-distribution] 2. The SIP ALG needs to be enabled, either implicitly / by default or by way of configuration. To confirm whether SIP ALG is enabled on SRX, and MX with SPC3 use the following command: user@host> show security alg status | match sip SIP : Enabled This issue affects Juniper Networks Junos OS on SRX 5000 Series: 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S2; 22.1 versions prior to 22.1R2-S2, 22.1R3; 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R1-S1, 22.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1.

An Uncontrolled Resource Consumption vulnerability in the PFE management daemon (evo-pfemand) of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to cause an FPC crash leading to a Denial of Service (DoS). When a specific SNMP GET operation or a specific CLI command is executed this will cause a GUID resource leak, eventually leading to exhaustion and result in an FPC crash and reboot. GUID exhaustion will trigger a syslog message like one of the following for example: evo-pfemand[<pid>]: get_next_guid: Ran out of Guid Space ... evo-aftmand-zx[<pid>]: get_next_guid: Ran out of Guid Space ... This leak can be monitored by running the following command and taking note of the value in the rightmost column labeled Guids: user@host> show platform application-info allocations app evo-pfemand | match "IFDId|IFLId|Context" Node Application Context Name Live Allocs Fails Guids re0 evo-pfemand net::juniper::interfaces::IFDId 0 3448 0 3448 re0 evo-pfemand net::juniper::interfaces::IFLId 0 561 0 561 user@host> show platform application-info allocations app evo-pfemand | match "IFDId|IFLId|Context" Node Application Context Name Live Allocs Fails Guids re0 evo-pfemand net::juniper::interfaces::IFDId 0 3784 0 3784 re0 evo-pfemand net::juniper::interfaces::IFLId 0 647 0 647 This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R3-S3-EVO; 21.1-EVO version 21.1R1-EVO and later versions; 21.2-EVO versions prior to 21.2R3-S4-EVO; 21.3-EVO version 21.3R1-EVO and later versions; 21.4-EVO versions prior to 21.4R2-EVO.

An Out-of-Bounds Write vulnerability in the H.323 ALG of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On all MX Series and SRX Series platform, when H.323 ALG is enabled and specific H.323 packets are received simultaneously, a flow processing daemon (flowd) crash will occur. Continued receipt of these specific packets will cause a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series All versions prior to 19.4R3-S10; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2.

A Missing Release of Memory after Effective Lifetime vulnerability in the Juniper Networks Junos OS on MX Series platforms with MPC10/MPC11 line cards, allows an unauthenticated adjacent attacker to cause a Denial of Service (DoS). Devices are only vulnerable when the Suspicious Control Flow Detection (scfd) feature is enabled. Upon enabling this specific feature, an attacker sending specific traffic is causing memory to be allocated dynamically and it is not freed. Memory is not freed even after deactivating this feature. Sustained processing of such traffic will eventually lead to an out of memory condition that prevents all services from continuing to function, and requires a manual restart to recover. The FPC memory usage can be monitored using the CLI command "show chassis fpc". On running the above command, the memory of AftDdosScfdFlow can be observed to detect the memory leak. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 20.2R3-S5; 20.3 version 20.3R1 and later versions.

On Juniper Networks Junos OS and Junos OS Evolved devices, BGP session flapping can lead to a routing process daemon (RPD) crash and restart, limiting the attack surface to configured BGP peers. This issue only affects devices with BGP damping in combination with accepted-prefix-limit configuration. When the issue occurs the following messages will appear in the /var/log/messages: rpd[6046]: %DAEMON-4-BGP_PREFIX_THRESH_EXCEEDED: XXXX (External AS x): Configured maximum accepted prefix-limit threshold(1800) exceeded for inet6-unicast nlri: 1984 (instance master) rpd[6046]: %DAEMON-3-BGP_CEASE_PREFIX_LIMIT_EXCEEDED: 2001:x:x:x::2 (External AS x): Shutting down peer due to exceeding configured maximum accepted prefix-limit(2000) for inet6-unicast nlri: 2001 (instance master) rpd[6046]: %DAEMON-4: bgp_rt_maxprefixes_check_common:9284: NOTIFICATION sent to 2001:x:x:x::2 (External AS x): code 6 (Cease) subcode 1 (Maximum Number of Prefixes Reached) AFI: 2 SAFI: 1 prefix limit 2000 kernel: %KERN-5: mastership_relinquish_on_process_exit: RPD crashed on master RE. Sending SIGUSR2 to chassisd (5612:chassisd) to trigger RE switchover This issue affects: Juniper Networks Junos OS: 17.2R3-S3; 17.3 version 17.3R3-S3 and later versions, prior to 17.3R3-S8; 17.4 version 17.4R2-S4, 17.4R3 and later versions, prior to 17.4R2-S10, 17.4R3-S2; 18.1 version 18.1R3-S6 and later versions, prior to 18.1R3-S10; 18.2 version 18.2R3 and later versions, prior to 18.2R3-S4; 18.2X75 version 18.2X75-D50, 18.2X75-D60 and later versions, prior to 18.2X75-D53, 18.2X75-D65; 18.3 version 18.3R2 and later versions, prior to 18.3R2-S4, 18.3R3-S2; 18.4 version 18.4R2 and later versions, prior to 18.4R2-S5, 18.4R3-S2; 19.1 version 19.1R1 and later versions, prior to 19.1R2-S2, 19.1R3-S1; 19.2 version 19.2R1 and later versions, prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2; 20.1 versions prior to 20.1R1-S2, 20.1R2. Juniper Networks Junos OS Evolved prior to 20.1R2-EVO. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R3-S3.

An Improper Check for Unusual or Exceptional Conditions vulnerability in BGP route processing of Juniper Networks Junos OS and Junos OS Evolved allows an attacker to cause Routing Protocol Daemon (RPD) crash by sending a BGP route with invalid next-hop resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects systems without import policy configured. This issue affects: Juniper Networks Junos OS 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R2-S2, 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2; 22.2 versions prior to 22.2R1-S1, 22.2R2. Juniper Networks Junos OS Evolved 21.4-EVO versions prior to 21.4R2-S2-EVO, 21.4R3-EVO; 22.1-EVO versions prior to 22.1R1-S2-EVO, 22.1R2-EVO; 22.2-EVO versions prior to 22.2R1-S1-EVO, 22.2R2-EVO. This issue does not affect: Juniper Networks Junos OS versions prior to 21.1R1. Juniper Networks Junos OS Evolved versions prior to 21.3R1-EVO.

On Juniper Networks PTX and QFX Series devices with packet sampling configured using tunnel-observation mpls-over-udp, sampling of a malformed packet can cause the Kernel Routing Table (KRT) queue to become stuck. KRT is the module within the Routing Process Daemon (RPD) that synchronized the routing tables with the forwarding tables in the kernel. This table is then synchronized to the Packet Forwarding Engine (PFE) via the KRT queue. Thus, when KRT queue become stuck, it can lead to unexpected packet forwarding issues. An administrator can monitor the following command to check if there is the KRT queue is stuck: user@device > show krt state ... Number of async queue entries: 65007 <--- this value keep on increasing. When this issue occurs, the following message might appear in the /var/log/messages: DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Too many delayed route/nexthop unrefs. Op 2 err 55, rtsm_id 5:-1, msg type 2 DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Memory usage of M_RTNEXTHOP type = (0) Max size possible for M_RTNEXTHOP type = (7297134592) Current delayed unref = (60000), Current unique delayed unref = (18420), Max delayed unref on this platform = (40000) Current delayed weight unref = (60000) Max delayed weight unref on this platform= (400000) curproc = rpd This issue affects Juniper Networks Junos OS on PTX/QFX Series: 17.2X75 versions prior to 17.2X75-D105; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.2X75 versions prior to 18.2X75-D420, 18.2X75-D53, 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R1-S7, 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2. This issue does not affect Juniper Networks Junos OS prior to 18.1R1.

An Improperly Implemented Security Check for Standard vulnerability in storm control of Juniper Networks Junos OS QFX5k devices allows packets to be punted to ARP queue causing a l2 loop resulting in a DDOS violations and DDOS syslog. This issue is triggered when Storm control is enabled and ICMPv6 packets are present on device. This issue affects Juniper Networks: Junos OS * All versions prior to 20.2R3-S6 on QFX5k; * 20.3 versions prior to 20.3R3-S5 on QFX5k; * 20.4 versions prior to 20.4R3-S5 on QFX5k; * 21.1 versions prior to 21.1R3-S4 on QFX5k; * 21.2 versions prior to 21.2R3-S3 on QFX5k; * 21.3 versions prior to 21.3R3-S2 on QFX5k; * 21.4 versions prior to 21.4R3 on QFX5k; * 22.1 versions prior to 22.1R3 on QFX5k; * 22.2 versions prior to 22.2R2 on QFX5k.

An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When a BGP update message is received over an established BGP session, and that message contains a specific, optional transitive attribute, this session will be torn down with an update message error. This issue cannot propagate beyond an affected system as the processing error occurs as soon as the update is received. This issue is exploitable remotely as the respective attribute can propagate through unaffected systems and intermediate AS (if any). Continuous receipt of a BGP update containing this attribute will create a sustained Denial of Service (DoS) condition. Some customers have experienced these BGP session flaps which prompted Juniper SIRT to release this advisory out of cycle before fixed releases are widely available as there is an effective workaround. This issue affects: Juniper Networks Junos OS 15.1R1 and later versions prior to 20.4R3-S8; 21.1 version 21.1R1 and later versions prior to 21.2R3-S6; 21.3 versions prior to 21.3R3-S5; 21.4 versions prior to 21.4R3-S4; 22.1 versions prior to 22.1R3-S4; 22.2 versions prior to 22.2R3-S2; 22.3 versions prior to 22.3R2-S2, 22.3R3-S1; 22.4 versions prior to 22.4R2-S1, 22.4R3; 23.1 versions prior to 23.1R1-S1, 23.1R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S8-EVO; 21.1 version 21.1R1-EVO and later versions prior to 21.2R3-S6-EVO; 21.3 versions prior to 21.3R3-S5-EVO; 21.4 versions prior to 21.4R3-S4-EVO; 22.1 versions prior to 22.1R3-S4-EVO; 22.2 versions prior to 22.2R3-S2-EVO; 22.3 versions prior to 22.3R2-S2-EVO, 22.3R3-S1-EVO; 22.4 versions prior to 22.4R2-S1-EVO, 22.4R3-EVO; 23.1 versions prior to 23.1R1-S1-EVO, 23.1R2-EVO.

An Improper Handling of Length Parameter Inconsistency vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network based, unauthenticated attacker to cause an RPD crash leading to a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Upon receipt of a malformed BGP flowspec update, RPD will crash resulting in a Denial of Service. This issue affects Juniper Networks Junos OS: All versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S1, 20.3R2; Juniper Networks Junos OS Evolved: All versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R2-EVO; 20.3 versions prior to 20.3R2-EVO;

An Allocation of Resources Without Limits or Throttling vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). On QFX10K Series, Inter-Chassis Control Protocol (ICCP) is used in MC-LAG topologies to exchange control information between the devices in the topology. ICCP connection flaps and sync issues will be observed due to excessive specific traffic to the local device. This issue affects Juniper Networks Junos OS on QFX10K Series: * All versions prior to 20.2R3-S7; * 20.4 versions prior to 20.4R3-S4; * 21.1 versions prior to 21.1R3-S3; * 21.2 versions prior to 21.2R3-S1; * 21.3 versions prior to 21.3R3; * 21.4 versions prior to 21.4R3; * 22.1 versions prior to 22.1R2.

A Buffer Overflow vulnerability in SIP ALG of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). On all MX Series and SRX Series platform with SIP ALG enabled, when a malformed SIP packet is received, the flow processing daemon (flowd) will crash and restart. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2; 22.2 versions prior to 22.2R1-S1, 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1 on SRX Series.

An Improper Handling of Unexpected Data Type vulnerability in the handling of SIP calls in Juniper Networks Junos OS on SRX Series and MX Series platforms allows an attacker to cause a memory leak leading to Denial of Services (DoS). This issue occurs on all MX Series platforms with MS-MPC or MS-MIC card and all SRX Series platforms where SIP ALG is enabled. Successful exploitation of this vulnerability prevents additional SIP calls and applications from succeeding. The SIP ALG needs to be enabled, either implicitly / by default or by way of configuration. To confirm whether SIP ALG is enabled on SRX use the following command: user@host> show security alg status | match sip SIP : Enabled This issue affects Juniper Networks Junos OS on SRX Series and on MX Series: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S10; 20.1 versions 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2-S2, 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2, 22.1R3-S1. This issue does not affect Juniper Networks Junos OS on SRX Series and on MX Series: All versions prior to 18.2R1.

An Improper Validation of Array Index vulnerability in the Advanced Forwarding Toolkit Manager daemon (aftmand) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). On the PTX10008 and PTX10016 platforms running Junos OS or Junos OS Evolved, when a specific SNMP MIB is queried this will cause a PFE crash and the FPC will go offline and not automatically recover. A system restart is required to get the affected FPC in an operational state again. This issue affects: Juniper Networks Junos OS 22.1 version 22.1R2 and later versions; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2. Juniper Networks Junos OS Evolved 21.3-EVO version 21.3R3-EVO and later versions; 21.4-EVO version 21.4R1-S2-EVO, 21.4R2-EVO and later versions prior to 21.4R2-S1-EVO; 22.1-EVO version 22.1R2-EVO and later versions prior to 22.1R3-EVO; 22.2-EVO versions prior to 22.2R1-S1-EVO, 22.2R2-EVO.

An Uncontrolled Resource Consumption vulnerability in TCP processing on the Routing Engine (RE) of Juniper Networks Junos OS allows an unauthenticated network-based attacker to send crafted TCP packets destined to the device, resulting in an MBUF leak that ultimately leads to a Denial of Service (DoS). The system does not recover automatically and must be manually restarted to restore service. This issue occurs when crafted TCP packets are sent directly to a configured IPv4 or IPv6 interface on the device. Transit traffic will not trigger this issue. MBUF usage can be monitored through the use of the 'show system buffers' command. For example: user@junos> show system buffers | refresh 5 4054/566/4620 mbufs in use (current/cache/total) ... 4089/531/4620 mbufs in use (current/cache/total) ... 4151/589/4740 mbufs in use (current/cache/total) ... 4213/527/4740 mbufs in use (current/cache/total) This issue affects Juniper Networks Junos OS: 12.3 version 12.3R12-S19 and later versions; 15.1 version 15.1R7-S10 and later versions; 17.3 version 17.3R3-S12 and later versions; 18.4 version 18.4R3-S9 and later versions; 19.1 version 19.1R3-S7 and later versions; 19.2 version 19.2R3-S3 and later versions; 19.3 version 19.3R2-S7, 19.3R3-S3 and later versions prior to 19.3R3-S7; 19.4 version 19.4R2-S7, 19.4R3-S5 and later versions prior to 19.4R3-S10; 20.1 version 20.1R3-S1 and later versions; 20.2 version 20.2R3-S2 and later versions prior to 20.2R3-S6; 20.3 version 20.3R3-S1 and later versions prior to 20.3R3-S6; 20.4 version 20.4R2-S2, 20.4R3 and later versions prior to 20.4R3-S5; 21.1 version 21.1R2 and later versions prior to 21.1R3-S4; 21.2 version 21.2R1-S1, 21.2R2 and later versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2; 22.3 versions prior to 22.3R1-S1, 22.3R2.

An Out-of-Bounds Write vulnerability in Flow Processing Daemon (flowd) of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On SRX Series devices using Unified Policies with IPv6, when a specific IPv6 packet goes through a dynamic-application filter which will generate an ICMP deny message, the flowd core is observed and the PFE is restarted. This issue affects: Juniper Networks Junos OS on SRX Series: 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R2.

When sFlow is enabled and it monitors a packet forwarded via ECMP, a buffer management vulnerability in the dcpfe process of Juniper Networks Junos OS on QFX10K Series systems allows an attacker to cause the Packet Forwarding Engine (PFE) to crash and restart by sending specific genuine packets to the device, resulting in a Denial of Service (DoS) condition. The dcpfe process tries to copy more data into a smaller buffer, which overflows and corrupts the buffer, causing a crash of the dcpfe process. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on QFX10K Series: All versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R2-S2, 21.4R3; 22.1 versions prior to 22.1R2; 22.2 versions prior to 22.2R1-S2, 22.2R2.

An Improper Locking vulnerability in the SIP ALG of Juniper Networks Junos OS on MX Series with MS-MPC or MS-MIC card and SRX Series allows an unauthenticated, network-based attacker to cause a flow processing daemon (flowd) crash and thereby a Denial of Service (DoS). Continued receipt of these specific packets will cause a sustained Denial of Service condition. This issue occurs when SIP ALG is enabled and specific SIP messages are processed simultaneously. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1 on MX Series, or SRX Series.

A Missing Release of Memory after Effective Lifetime vulnerability in the Flow Processing Daemon (flowd) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). In an IPsec VPN environment, a memory leak will be seen if a DH or ECDH group is configured. Eventually the flowd process will crash and restart. This issue affects Juniper Networks Junos OS on SRX Series: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S10; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2.

An Improper Input Validation vulnerability in the syslog stream TCP transport of Juniper Networks Junos OS on MX240, MX480 and MX960 devices with MX-SPC3 Security Services Card allows an unauthenticated, network-based attacker, to send specific spoofed packets to cause a CPU Denial of Service (DoS) to the MX-SPC3 SPUs. Continued receipt and processing of these specific packets will sustain the DoS condition. This issue affects Junos OS: * All versions before 22.2R3-S6, * from 22.4 before 22.4R3-S4, * from 23.2 before 23.2R2-S3, * from 23.4 before 23.4R2-S4, * from 24.2 before 24.2R1-S2, 24.2R2 An indicator of compromise will indicate the SPC3 SPUs utilization has spiked. For example:     user@device> show services service-sets summary Service sets CPU Interface configured Bytes used Session bytes used Policy bytes used utilization "interface" 1 "bytes" (percent%) "sessions" ("percent"%) "bytes" ("percent"%) 99.97 % OVLD <<<<<< look for high CPU usage

An Improper Handling of Additional Special Element vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on MX Series with MS-MPC, MS-MIC and SPC3, and SRX Series, allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). If the SIP ALG processes specifically formatted SIP invites, a memory corruption will occur which will lead to a crash of the FPC processing these packets. Although the system will automatically recover with the restart of the FPC, subsequent SIP invites will cause the crash again and lead to a sustained DoS. This issue affects Junos OS on MX Series and SRX Series:  * all versions before 21.2R3-S9, * 21.4 versions before 21.4R3-S10, * 22.2 versions before 22.2R3-S6, * 22.4 versions before 22.4R3-S5, * 23.2 versions before 23.2R2-S3, * 23.4 versions before 23.4R2-S3, * 24.2 versions before 24.2R1-S2, 24.2R2.

A NULL Pointer Dereference vulnerability in the flow daemon (flowd) of Juniper Networks Junos OS on SRX Series allows an attacker causing specific, valid control traffic to be sent out of a Dual-Stack (DS) Lite tunnel to crash the flowd process, resulting in a Denial of Service (DoS).  Continuous triggering of specific control traffic will create a sustained Denial of Service (DoS) condition. On all SRX platforms, when specific, valid control traffic needs to be sent out of a DS-Lite tunnel, a segmentation fault occurs within the flowd process, resulting in a network outage until the flowd process restarts. This issue affects Junos OS on SRX Series: * All versions before 21.2R3-S9, * from 21.4 before 21.4R3-S9, * from 22.2 before 22.2R3-S5, * from 22.4 before 22.4R3-S6, * from 23.2 before 23.2R2-S3, * from 23.4 before 23.4R2.

A Buffer Access with Incorrect Length Value vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When an attacker sends a specific ICMPv6 packet to an interface with "protocols router-advertisement" configured, rpd crashes and restarts. Continued receipt of this packet will cause a sustained DoS condition.  This issue only affects systems configured with IPv6. This issue affects Junos OS:  * All versions before 21.2R3-S9,  * from 21.4 before 21.4R3-S10, * from 22.2 before 22.2R3-S6, * from 22.4 before 22.4R3-S4, * from 23.2 before 23.2R2-S2, * from 23.4 before 23.4R2; and Junos OS Evolved: * All versions before 21.2R3-S9-EVO, * from 21.4-EVO before 21.4R3-S10-EVO, * from 22.2-EVO before 22.2R3-S6-EVO, * from 22.4-EVO before 22.4R3-S4-EVO, * from 23.2-EVO before 23.2R2-S2-EVO, * from 23.4-EVO before 23.4R2-EVO.

An Improper Handling of Length Parameter Inconsistency vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). When a device configured for Secure Vector Routing (SVR) receives a specifically malformed packet the PFE will crash and restart. This issue affects Junos OS on SRX Series: * All 21.4 versions, * 22.2 versions before 22.2R3-S6, * 22.4 versions before 22.4R3-S6, * 23.2 versions before 23.2R2-S3, * 23.4 versions before 23.4R2-S4, * 24.2 versions before 24.2R2. This issue does not affect versions before 21.4.

A Missing Release of Memory after Effective Lifetime vulnerability in the Anti-Virus processing of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). On all SRX platforms with Anti-Virus enabled, if a server sends specific content in the HTTP body of a response to a client request, these packets are queued by Anti-Virus processing in Juniper Buffers (jbufs) which are never released. When these jbufs are exhausted, the device stops forwarding all transit traffic. A jbuf memory leak can be noticed from the following logs: (<node>.)<fpc> Warning: jbuf pool id <#> utilization level (<current level>%) is above <threshold>%! To recover from this issue, the affected device needs to be manually rebooted to free the leaked jbufs. This issue affects Junos OS on SRX Series:  * all versions before 21.2R3-S9, * 21.4 versions before 21.4R3-S10, * 22.2 versions before 22.2R3-S6, * 22.4 versions before 22.4R3-S6, * 23.2 versions before 23.2R2-S3, * 23.4 versions before 23.4R2-S3, * 24.2 versions before 24.2R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on MX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS).When processing a high rate of specific GRE traffic destined to the device, the respective PFE will hang causing traffic forwarding to stop. When this issue occurs the following logs can be observed: <fpc #> MQSS(0): LI-3: Received a parcel with more than 512B accompanying data CHASSISD_FPC_ASIC_ERROR: ASIC Error detected <...> This issue affects Junos OS: * all versions before 21.2R3-S9, * 21.4 versions before 21.4R3-S8, * 22.2 versions before 22.2R3-S4, * 22.4 versions before 22.4R3-S5, * 23.2 versions before 23.2R2-S2, * 23.4 versions before 23.4R2.

On Junos devices with the BGP graceful restart helper mode enabled or the BGP graceful restart mechanism enabled, a certain sequence of BGP session restart on a remote peer that has the graceful restart mechanism enabled may cause the local routing protocol daemon (RPD) process to crash and restart. Repeated crashes of the RPD process can cause prolonged Denial of Service (DoS). Graceful restart helper mode for BGP is enabled by default. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S3; 16.2 versions prior to 16.2R2-S9; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3; 17.2X75 versions prior to 17.2X75-D105; 17.3 versions prior to 17.3R3-S2; 17.4 versions prior to 17.4R1-S7, 17.4R2-S2, 17.4R3; 18.1 versions prior to 18.1R3-S2; 18.2 versions prior to 18.2R2; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D30; 18.3 versions prior to 18.3R1-S4, 18.3R2. Junos OS releases prior to 16.1R1 are not affected.

An unexpected status return value weakness in the Next-Generation Multicast VPN (NG-mVPN) service of Juniper Networks Junos OS allows attacker to cause a Denial of Service (DoS) condition and core the routing protocol daemon (rpd) process when a specific malformed IPv4 packet is received by the device running BGP. This malformed packet can be crafted and sent to a victim device including when forwarded directly through a device receiving such a malformed packet, but not if the malformed packet is first de-encapsulated from an encapsulated format by a receiving device. Continued receipt of the malformed packet will result in a sustained Denial of Service condition. This issue affects: Juniper Networks Junos OS 15.1 versions prior to 15.1F6-S12, 15.1R7-S2; 15.1X49 versions prior to 15.1X49-D150 on SRX Series; 15.1X53 versions prior to 15.1X53-D68, 15.1X53-D235, 15.1X53-D495, 15.1X53-D590; 16.1 versions prior to 16.1R3-S10, 16.1R4-S12, 16.1R6-S6, 16.1R7-S2; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S9, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R2-S6, 17.2R3; 17.3 versions prior to 17.3R2-S4, 17.3R3.

A Missing Release of Memory after Effective Lifetime vulnerability in the routing process daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an attacker to send a malformed BGP Path attribute update which allocates memory used to log the bad path attribute. This memory is not properly freed in all circumstances, leading to a Denial of Service (DoS). Consumed memory can be freed by manually restarting Routing Protocol Daemon (rpd). Memory utilization could be monitored by:  user@host> show system memory or show system monitor memory status This issue affects: Junos OS:  * All versions before 21.2R3-S8,  * from 21.4 before 21.4R3-S8, * from 22.2 before 22.2R3-S4,  * from 22.3 before 22.3R3-S3,  * from 22.4 before 22.4R3-S3, * from 23.2 before 23.2R2-S1,  * from 23.4 before 23.4R1-S2, 23.4R2. Junos OS Evolved: * All versions before 21.2R3-S8-EVO, * from 21.4 before 21.4R3-S8-EVO, * from 22.2 before 22.2R3-S4-EVO, * from 22.3 before 22.3R3-S3-EVO, * from 22.4 before 22.4R3-S3-EVO, * from 23.2 before 23.2R2-S1-EVO, * from 23.4 before 23.4R1-S2-EVO, 23.4R2-EVO.

An Improper Validation of Syntactic Correctness of Input vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on MX Series with MPC10/11 or LC9600, MX304, and Junos OS Evolved on ACX Series and PTX Series allows an unauthenticated, network based attacker to cause a Denial-of-Service (DoS). This issue can occur in two scenarios: 1. If a device, which is configured with SFLOW and ECMP, receives specific valid transit traffic, which is subject to sampling, the packetio process crashes, which in turn leads to an evo-aftman crash and causes the FPC to stop working until it is restarted. (This scenario is only applicable to PTX but not to ACX or MX.) 2. If a device receives a malformed CFM packet on an interface configured with CFM, the packetio process crashes, which in turn leads to an evo-aftman crash and causes the FPC to stop working until it is restarted. Please note that the CVSS score is for the formally more severe issue 1. The CVSS score for scenario 2. is: 6.5 (CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:U/C:N/I:N/A:H) This issue affects Junos OS: * All versions before 21.2R3-S4, * 21.4 versions before 21.4R2, * 22.2 versions before 22.2R3-S2;  Junos OS Evolved: * All versions before 21.2R3-S8-EVO, * 21.4 versions before 21.4R2-EVO.

On Juniper Networks Junos OS and Junos OS Evolved devices processing a specially crafted BGP UPDATE or KEEPALIVE message can lead to a routing process daemon (RPD) crash and restart, causing a Denial of Service (DoS). Continued receipt and processing of this message will create a sustained Denial of Service (DoS) condition. This issue affects both IBGP and EBGP deployments over IPv4 or IPv6. This issue affects: Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1; 19.4 versions prior to 19.4R1-S4, 19.4R1-S4, 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S1, 20.3R2. Juniper Networks Junos OS Evolved: 20.3 versions prior to 20.3R2-EVO.

An Improper Validation of Specified Type of Input vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS allows an attacker to cause an RPD memory leak leading to a Denial of Service (DoS). This memory leak only occurs when the attacker's packets are destined to any configured IPv6 address on the device. This issue affects: Juniper Networks Junos OS 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2; 22.1 versions prior to 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 21.1R1.

In Point to MultiPoint (P2MP) scenarios within established sessions between network or adjacent neighbors the improper use of a source to destination copy write operation combined with a Stack-based Buffer Overflow on certain specific packets processed by the routing protocol daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved sent by a remote unauthenticated network attacker causes the RPD to crash causing a Denial of Service (DoS). Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 19.2R1. Juniper Networks Junos OS Evolved 20.1 versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R3-EVO; 20.3 versions prior to 20.3R2-EVO.

An Improper Check for Unusual or Exceptional Conditions in packet processing on the MS-MPC/MS-MIC utilized by Juniper Networks Junos OS allows a malicious attacker to send a specific packet, triggering the MS-MPC/MS-MIC to reset, causing a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects specific versions of Juniper Networks Junos OS on MX Series: 17.3R3-S11; 17.4R2-S13; 17.4R3 prior to 17.4R3-S5; 18.1R3-S12; 18.2R2-S8, 18.2R3-S7, 18.2R3-S8; 18.3R3-S4; 18.4R3-S7; 19.1R3-S4, 19.1R3-S5; 19.2R1-S6; 19.3R3-S2; 19.4R2-S4, 19.4R2-S5; 19.4R3-S2; 20.1R2-S1; 20.2R2-S2, 20.2R2-S3, 20.2R3; 20.3R2, 20.3R2-S1; 20.4R1, 20.4R1-S1, 20.4R2; 21.1R1; This issue does not affect any version of Juniper Networks Junos OS prior to 15.1X49-D240;

An Uncontrolled Resource Consumption vulnerability in the kernel of Juniper Networks JUNOS OS allows an unauthenticated network based attacker to cause 100% CPU load and the device to become unresponsive by sending a flood of traffic to the out-of-band management ethernet port. Continued receipted of a flood will create a sustained Denial of Service (DoS) condition. Once the flood subsides the system will recover by itself. An indication that the system is affected by this issue would be that kernel and netisr process are shown to be using a lot of CPU cycles like in the following example output: user@host> show system processes extensive ... PID USERNAME PRI NICE SIZE RES STATE C TIME WCPU COMMAND 16 root -72 - 0K 304K WAIT 1 839:40 88.96% intr{swi1: netisr 0} 0 root 97 - 0K 160K RUN 1 732:43 87.99% kernel{bcm560xgmac0 que} This issue affects Juniper Networks JUNOS OS on EX2300 Series, EX3400 Series, and ACX710: All versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S9; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2.

An Improper Input Validation vulnerability in Packet Forwarding Engine manager (FXPC) process of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) by sending specific DHCPv6 packets to the device and crashing the FXPC service. Continued receipt and processing of this specific packet will create a sustained Denial of Service (DoS) condition. This issue affects only the following platforms in ACX Series: ACX500, ACX1000, ACX1100, ACX2100, ACX2200, ACX4000, ACX5048, ACX5096 devices. Other ACX platforms are not affected from this issue. This issue affects Juniper Networks Junos OS on ACX500, ACX1000, ACX1100, ACX2100, ACX2200, ACX4000, ACX5048, ACX5096: 18.4 version 18.4R3-S7 and later versions prior to 18.4R3-S8. This issue does not affect: Juniper Networks Junos OS 18.4 versions prior to 18.4R3-S7 on ACX500, ACX1000, ACX1100, ACX2100, ACX2200, ACX4000, ACX5048, ACX5096.

An Incorrect Behavior Order vulnerability in the MAP-E automatic tunneling mechanism of Juniper Networks Junos OS allows an attacker to send certain malformed IPv4 or IPv6 packets to cause a Denial of Service (DoS) to the PFE on the device which is disabled as a result of the processing of these packets. Continued receipt and processing of these malformed IPv4 or IPv6 packets will create a sustained Denial of Service (DoS) condition. This issue only affects MPC 7/8/9/10/11 cards, when MAP-E IP reassembly is enabled on these cards. An indicator of compromise is the output: FPC ["FPC ID" # e.g. "0"] PFE #{PFE ID # e.g. "1"] : Fabric Disabled Example: FPC 0 PFE #1 : Fabric Disabled when using the command: show chassis fabric fpcs An example of a healthy result of the command use would be: user@device-re1> show chassis fabric fpcs Fabric management FPC state: FPC 0 PFE #0 Plane 0: Plane enabled Plane 1: Plane enabled Plane 2: Plane enabled Plane 3: Plane enabled Plane 4: Plane enabled Plane 5: Plane enabled Plane 6: Plane enabled Plane 7: Plane enabled This issue affects: Juniper Networks Junos OS on MX Series with MPC 7/8/9/10/11 cards, when MAP-E IP reassembly is enabled on these cards. 17.2 version 17.2R1 and later versions; 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S12, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S1; 18.4 versions prior to 18.4R1-S8, 18.4R2-S5, 18.4R3; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S5, 19.3R3. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R1.

A Missing Release of Memory after Effective Lifetime vulnerability in the Juniper Tunnel Driver (jtd) of Juniper Networks Junos OS Evolved allows an unauthenticated network-based attacker to cause Denial of Service.  Receipt of specifically malformed IPv6 packets, destined to the device, causes kernel memory to not be freed, resulting in memory exhaustion leading to a system crash and Denial of Service (DoS). Continuous receipt and processing of these packets will continue to exhaust kernel memory, creating a sustained Denial of Service (DoS) condition. This issue only affects systems configured with IPv6. This issue affects Junos OS Evolved:  * from 22.4-EVO before 22.4R3-S5-EVO,  * from 23.2-EVO before 23.2R2-S2-EVO,  * from 23.4-EVO before 23.4R2-S2-EVO,  * from 24.2-EVO before 24.2R1-S2-EVO, 24.2R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 22.4R1-EVO.