In the Linux kernel, the following vulnerability has been resolved: gpio: pca953x: fix pca953x_irq_bus_sync_unlock race Ensure that `i2c_lock' is held when setting interrupt latch and mask in pca953x_irq_bus_sync_unlock() in order to avoid races. The other (non-probe) call site pca953x_gpio_set_multiple() ensures the lock is held before calling pca953x_write_regs(). The problem occurred when a request raced against irq_bus_sync_unlock() approximately once per thousand reboots on an i.MX8MP based system. * Normal case 0-0022: write register AI|3a {03,02,00,00,01} Input latch P0 0-0022: write register AI|49 {fc,fd,ff,ff,fe} Interrupt mask P0 0-0022: write register AI|08 {ff,00,00,00,00} Output P3 0-0022: write register AI|12 {fc,00,00,00,00} Config P3 * Race case 0-0022: write register AI|08 {ff,00,00,00,00} Output P3 0-0022: write register AI|08 {03,02,00,00,01} *** Wrong register *** 0-0022: write register AI|12 {fc,00,00,00,00} Config P3 0-0022: write register AI|49 {fc,fd,ff,ff,fe} Interrupt mask P0

Race condition in Linux 2.6, when threads are sharing memory mapping via CLONE_VM (such as linuxthreads and vfork), might allow local users to cause a denial of service (deadlock) by triggering a core dump while waiting for a thread that has just performed an exec.

In the Linux kernel, the following vulnerability has been resolved: vfs: Don't evict inode under the inode lru traversing context The inode reclaiming process(See function prune_icache_sb) collects all reclaimable inodes and mark them with I_FREEING flag at first, at that time, other processes will be stuck if they try getting these inodes (See function find_inode_fast), then the reclaiming process destroy the inodes by function dispose_list(). Some filesystems(eg. ext4 with ea_inode feature, ubifs with xattr) may do inode lookup in the inode evicting callback function, if the inode lookup is operated under the inode lru traversing context, deadlock problems may happen. Case 1: In function ext4_evict_inode(), the ea inode lookup could happen if ea_inode feature is enabled, the lookup process will be stuck under the evicting context like this: 1. File A has inode i_reg and an ea inode i_ea 2. getfattr(A, xattr_buf) // i_ea is added into lru // lru->i_ea 3. Then, following three processes running like this: PA PB echo 2 > /proc/sys/vm/drop_caches shrink_slab prune_dcache_sb // i_reg is added into lru, lru->i_ea->i_reg prune_icache_sb list_lru_walk_one inode_lru_isolate i_ea->i_state |= I_FREEING // set inode state inode_lru_isolate __iget(i_reg) spin_unlock(&i_reg->i_lock) spin_unlock(lru_lock) rm file A i_reg->nlink = 0 iput(i_reg) // i_reg->nlink is 0, do evict ext4_evict_inode ext4_xattr_delete_inode ext4_xattr_inode_dec_ref_all ext4_xattr_inode_iget ext4_iget(i_ea->i_ino) iget_locked find_inode_fast __wait_on_freeing_inode(i_ea) ----→ AA deadlock dispose_list // cannot be executed by prune_icache_sb wake_up_bit(&i_ea->i_state) Case 2: In deleted inode writing function ubifs_jnl_write_inode(), file deleting process holds BASEHD's wbuf->io_mutex while getting the xattr inode, which could race with inode reclaiming process(The reclaiming process could try locking BASEHD's wbuf->io_mutex in inode evicting function), then an ABBA deadlock problem would happen as following: 1. File A has inode ia and a xattr(with inode ixa), regular file B has inode ib and a xattr. 2. getfattr(A, xattr_buf) // ixa is added into lru // lru->ixa 3. Then, following three processes running like this: PA PB PC echo 2 > /proc/sys/vm/drop_caches shrink_slab prune_dcache_sb // ib and ia are added into lru, lru->ixa->ib->ia prune_icache_sb list_lru_walk_one inode_lru_isolate ixa->i_state |= I_FREEING // set inode state inode_lru_isolate __iget(ib) spin_unlock(&ib->i_lock) spin_unlock(lru_lock) rm file B ib->nlink = 0 rm file A iput(ia) ubifs_evict_inode(ia) ubifs_jnl_delete_inode(ia) ubifs_jnl_write_inode(ia) make_reservation(BASEHD) // Lock wbuf->io_mutex ubifs_iget(ixa->i_ino) iget_locked find_inode_fast __wait_on_freeing_inode(ixa) | iput(ib) // ib->nlink is 0, do evict | ubifs_evict_inode | ubifs_jnl_delete_inode(ib) ↓ ubifs_jnl_write_inode ABBA deadlock ←-----make_reservation(BASEHD) dispose_list // cannot be executed by prune_icache_sb wake_up_bit(&ixa->i_state) Fix the possible deadlock by using new inode state flag I_LRU_ISOLATING to pin the inode in memory while inode_lru_isolate( ---truncated---

The inode double locking code in fs/ocfs2/file.c in the Linux kernel 2.6.30 before 2.6.30-rc3, 2.6.27 before 2.6.27.24, 2.6.29 before 2.6.29.4, and possibly other versions down to 2.6.19 allows local users to cause a denial of service (prevention of file creation and removal) via a series of splice system calls that trigger a deadlock between the generic_file_splice_write, splice_from_pipe, and ocfs2_file_splice_write functions.

In the Linux kernel, the following vulnerability has been resolved: ice: Fix race condition during interface enslave Commit 5dbbbd01cbba83 ("ice: Avoid RTNL lock when re-creating auxiliary device") changes a process of re-creation of aux device so ice_plug_aux_dev() is called from ice_service_task() context. This unfortunately opens a race window that can result in dead-lock when interface has left LAG and immediately enters LAG again. Reproducer: ``` #!/bin/sh ip link add lag0 type bond mode 1 miimon 100 ip link set lag0 for n in {1..10}; do echo Cycle: $n ip link set ens7f0 master lag0 sleep 1 ip link set ens7f0 nomaster done ``` This results in: [20976.208697] Workqueue: ice ice_service_task [ice] [20976.213422] Call Trace: [20976.215871] __schedule+0x2d1/0x830 [20976.219364] schedule+0x35/0xa0 [20976.222510] schedule_preempt_disabled+0xa/0x10 [20976.227043] __mutex_lock.isra.7+0x310/0x420 [20976.235071] enum_all_gids_of_dev_cb+0x1c/0x100 [ib_core] [20976.251215] ib_enum_roce_netdev+0xa4/0xe0 [ib_core] [20976.256192] ib_cache_setup_one+0x33/0xa0 [ib_core] [20976.261079] ib_register_device+0x40d/0x580 [ib_core] [20976.266139] irdma_ib_register_device+0x129/0x250 [irdma] [20976.281409] irdma_probe+0x2c1/0x360 [irdma] [20976.285691] auxiliary_bus_probe+0x45/0x70 [20976.289790] really_probe+0x1f2/0x480 [20976.298509] driver_probe_device+0x49/0xc0 [20976.302609] bus_for_each_drv+0x79/0xc0 [20976.306448] __device_attach+0xdc/0x160 [20976.310286] bus_probe_device+0x9d/0xb0 [20976.314128] device_add+0x43c/0x890 [20976.321287] __auxiliary_device_add+0x43/0x60 [20976.325644] ice_plug_aux_dev+0xb2/0x100 [ice] [20976.330109] ice_service_task+0xd0c/0xed0 [ice] [20976.342591] process_one_work+0x1a7/0x360 [20976.350536] worker_thread+0x30/0x390 [20976.358128] kthread+0x10a/0x120 [20976.365547] ret_from_fork+0x1f/0x40 ... [20976.438030] task:ip state:D stack: 0 pid:213658 ppid:213627 flags:0x00004084 [20976.446469] Call Trace: [20976.448921] __schedule+0x2d1/0x830 [20976.452414] schedule+0x35/0xa0 [20976.455559] schedule_preempt_disabled+0xa/0x10 [20976.460090] __mutex_lock.isra.7+0x310/0x420 [20976.464364] device_del+0x36/0x3c0 [20976.467772] ice_unplug_aux_dev+0x1a/0x40 [ice] [20976.472313] ice_lag_event_handler+0x2a2/0x520 [ice] [20976.477288] notifier_call_chain+0x47/0x70 [20976.481386] __netdev_upper_dev_link+0x18b/0x280 [20976.489845] bond_enslave+0xe05/0x1790 [bonding] [20976.494475] do_setlink+0x336/0xf50 [20976.502517] __rtnl_newlink+0x529/0x8b0 [20976.543441] rtnl_newlink+0x43/0x60 [20976.546934] rtnetlink_rcv_msg+0x2b1/0x360 [20976.559238] netlink_rcv_skb+0x4c/0x120 [20976.563079] netlink_unicast+0x196/0x230 [20976.567005] netlink_sendmsg+0x204/0x3d0 [20976.570930] sock_sendmsg+0x4c/0x50 [20976.574423] ____sys_sendmsg+0x1eb/0x250 [20976.586807] ___sys_sendmsg+0x7c/0xc0 [20976.606353] __sys_sendmsg+0x57/0xa0 [20976.609930] do_syscall_64+0x5b/0x1a0 [20976.613598] entry_SYSCALL_64_after_hwframe+0x65/0xca 1. Command 'ip link ... set nomaster' causes that ice_plug_aux_dev() is called from ice_service_task() context, aux device is created and associated device->lock is taken. 2. Command 'ip link ... set master...' calls ice's notifier under RTNL lock and that notifier calls ice_unplug_aux_dev(). That function tries to take aux device->lock but this is already taken by ice_plug_aux_dev() in step 1 3. Later ice_plug_aux_dev() tries to take RTNL lock but this is already taken in step 2 4. Dead-lock The patch fixes this issue by following changes: - Bit ICE_FLAG_PLUG_AUX_DEV is kept to be set during ice_plug_aux_dev() call in ice_service_task() - The bit is checked in ice_clear_rdma_cap() and only if it is not set then ice_unplug_aux_dev() is called. If it is set (in other words plugging of aux device was requested and ice_plug_aux_dev() is potentially running) then the function only clears the ---truncated---

A race condition flaw was found in the Linux kernel sound subsystem due to improper locking. It could lead to a NULL pointer dereference while handling the SNDCTL_DSP_SYNC ioctl. A privileged local user (root or member of the audio group) could use this flaw to crash the system, resulting in a denial of service condition

In the Linux kernel, the following vulnerability has been resolved: s390/qeth: fix deadlock during failing recovery Commit 0b9902c1fcc5 ("s390/qeth: fix deadlock during recovery") removed taking discipline_mutex inside qeth_do_reset(), fixing potential deadlocks. An error path was missed though, that still takes discipline_mutex and thus has the original deadlock potential. Intermittent deadlocks were seen when a qeth channel path is configured offline, causing a race between qeth_do_reset and ccwgroup_remove. Call qeth_set_offline() directly in the qeth_do_reset() error case and then a new variant of ccwgroup_set_offline(), without taking discipline_mutex.

A deadlock flaw was found in the Linux kernel’s BPF subsystem. This flaw allows a local user to potentially crash the system.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix i_data_sem unlock order in ext4_ind_migrate() Fuzzing reports a possible deadlock in jbd2_log_wait_commit. This issue is triggered when an EXT4_IOC_MIGRATE ioctl is set to require synchronous updates because the file descriptor is opened with O_SYNC. This can lead to the jbd2_journal_stop() function calling jbd2_might_wait_for_commit(), potentially causing a deadlock if the EXT4_IOC_MIGRATE call races with a write(2) system call. This problem only arises when CONFIG_PROVE_LOCKING is enabled. In this case, the jbd2_might_wait_for_commit macro locks jbd2_handle in the jbd2_journal_stop function while i_data_sem is locked. This triggers lockdep because the jbd2_journal_start function might also lock the same jbd2_handle simultaneously. Found by Linux Verification Center (linuxtesting.org) with syzkaller. Rule: add

In the Linux kernel, the following vulnerability has been resolved: fgraph: Add READ_ONCE() when accessing fgraph_array[] In __ftrace_return_to_handler(), a loop iterates over the fgraph_array[] elements, which are fgraph_ops. The loop checks if an element is a fgraph_stub to prevent using a fgraph_stub afterward. However, if the compiler reloads fgraph_array[] after this check, it might race with an update to fgraph_array[] that introduces a fgraph_stub. This could result in the stub being processed, but the stub contains a null "func_hash" field, leading to a NULL pointer dereference. To ensure that the gops compared against the fgraph_stub matches the gops processed later, add a READ_ONCE(). A similar patch appears in commit 63a8dfb ("function_graph: Add READ_ONCE() when accessing fgraph_array[]").

In the Linux kernel, the following vulnerability has been resolved: iommu/arm-smmu: Defer probe of clients after smmu device bound Null pointer dereference occurs due to a race between smmu driver probe and client driver probe, when of_dma_configure() for client is called after the iommu_device_register() for smmu driver probe has executed but before the driver_bound() for smmu driver has been called. Following is how the race occurs: T1:Smmu device probe T2: Client device probe really_probe() arm_smmu_device_probe() iommu_device_register() really_probe() platform_dma_configure() of_dma_configure() of_dma_configure_id() of_iommu_configure() iommu_probe_device() iommu_init_device() arm_smmu_probe_device() arm_smmu_get_by_fwnode() driver_find_device_by_fwnode() driver_find_device() next_device() klist_next() /* null ptr assigned to smmu */ /* null ptr dereference while smmu->streamid_mask */ driver_bound() klist_add_tail() When this null smmu pointer is dereferenced later in arm_smmu_probe_device, the device crashes. Fix this by deferring the probe of the client device until the smmu device has bound to the arm smmu driver. [will: Add comment]

In the Linux kernel, the following vulnerability has been resolved: mm: revert "mm: shmem: fix data-race in shmem_getattr()" Revert d949d1d14fa2 ("mm: shmem: fix data-race in shmem_getattr()") as suggested by Chuck [1]. It is causing deadlocks when accessing tmpfs over NFS. As Hugh commented, "added just to silence a syzbot sanitizer splat: added where there has never been any practical problem".

An issue was discovered in the Linux kernel through 6.5.9. During a race with SQ thread exit, an io_uring/fdinfo.c io_uring_show_fdinfo NULL pointer dereference can occur.

In the Linux kernel, the following vulnerability has been resolved: tracing/timerlat: Fix a race during cpuhp processing There is another found exception that the "timerlat/1" thread was scheduled on CPU0, and lead to timer corruption finally: ``` ODEBUG: init active (active state 0) object: ffff888237c2e108 object type: hrtimer hint: timerlat_irq+0x0/0x220 WARNING: CPU: 0 PID: 426 at lib/debugobjects.c:518 debug_print_object+0x7d/0xb0 Modules linked in: CPU: 0 UID: 0 PID: 426 Comm: timerlat/1 Not tainted 6.11.0-rc7+ #45 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 RIP: 0010:debug_print_object+0x7d/0xb0 ... Call Trace: <TASK> ? __warn+0x7c/0x110 ? debug_print_object+0x7d/0xb0 ? report_bug+0xf1/0x1d0 ? prb_read_valid+0x17/0x20 ? handle_bug+0x3f/0x70 ? exc_invalid_op+0x13/0x60 ? asm_exc_invalid_op+0x16/0x20 ? debug_print_object+0x7d/0xb0 ? debug_print_object+0x7d/0xb0 ? __pfx_timerlat_irq+0x10/0x10 __debug_object_init+0x110/0x150 hrtimer_init+0x1d/0x60 timerlat_main+0xab/0x2d0 ? __pfx_timerlat_main+0x10/0x10 kthread+0xb7/0xe0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2d/0x40 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> ``` After tracing the scheduling event, it was discovered that the migration of the "timerlat/1" thread was performed during thread creation. Further analysis confirmed that it is because the CPU online processing for osnoise is implemented through workers, which is asynchronous with the offline processing. When the worker was scheduled to create a thread, the CPU may has already been removed from the cpu_online_mask during the offline process, resulting in the inability to select the right CPU: T1 | T2 [CPUHP_ONLINE] | cpu_device_down() osnoise_hotplug_workfn() | | cpus_write_lock() | takedown_cpu(1) | cpus_write_unlock() [CPUHP_OFFLINE] | cpus_read_lock() | start_kthread(1) | cpus_read_unlock() | To fix this, skip online processing if the CPU is already offline.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to check atomic_file in f2fs ioctl interfaces Some f2fs ioctl interfaces like f2fs_ioc_set_pin_file(), f2fs_move_file_range(), and f2fs_defragment_range() missed to check atomic_write status, which may cause potential race issue, fix it.

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix a race between socket set up and I/O thread creation In rxrpc_open_socket(), it sets up the socket and then sets up the I/O thread that will handle it. This is a problem, however, as there's a gap between the two phases in which a packet may come into rxrpc_encap_rcv() from the UDP packet but we oops when trying to wake the not-yet created I/O thread. As a quick fix, just make rxrpc_encap_rcv() discard the packet if there's no I/O thread yet. A better, but more intrusive fix would perhaps be to rearrange things such that the socket creation is done by the I/O thread.

In the Linux kernel, the following vulnerability has been resolved: drm/panthor: Fix race when converting group handle to group object XArray provides it's own internal lock which protects the internal array when entries are being simultaneously added and removed. However there is still a race between retrieving the pointer from the XArray and incrementing the reference count. To avoid this race simply hold the internal XArray lock when incrementing the reference count, this ensures there cannot be a racing call to xa_erase().

In the Linux kernel, the following vulnerability has been resolved: blk-rq-qos: fix crash on rq_qos_wait vs. rq_qos_wake_function race We're seeing crashes from rq_qos_wake_function that look like this: BUG: unable to handle page fault for address: ffffafe180a40084 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 100000067 P4D 100000067 PUD 10027c067 PMD 10115d067 PTE 0 Oops: Oops: 0002 [#1] PREEMPT SMP PTI CPU: 17 UID: 0 PID: 0 Comm: swapper/17 Not tainted 6.12.0-rc3-00013-geca631b8fe80 #11 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:_raw_spin_lock_irqsave+0x1d/0x40 Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 0f 1f 44 00 00 41 54 9c 41 5c fa 65 ff 05 62 97 30 4c 31 c0 ba 01 00 00 00 <f0> 0f b1 17 75 0a 4c 89 e0 41 5c c3 cc cc cc cc 89 c6 e8 2c 0b 00 RSP: 0018:ffffafe180580ca0 EFLAGS: 00010046 RAX: 0000000000000000 RBX: ffffafe180a3f7a8 RCX: 0000000000000011 RDX: 0000000000000001 RSI: 0000000000000003 RDI: ffffafe180a40084 RBP: 0000000000000000 R08: 00000000001e7240 R09: 0000000000000011 R10: 0000000000000028 R11: 0000000000000888 R12: 0000000000000002 R13: ffffafe180a40084 R14: 0000000000000000 R15: 0000000000000003 FS: 0000000000000000(0000) GS:ffff9aaf1f280000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffafe180a40084 CR3: 000000010e428002 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <IRQ> try_to_wake_up+0x5a/0x6a0 rq_qos_wake_function+0x71/0x80 __wake_up_common+0x75/0xa0 __wake_up+0x36/0x60 scale_up.part.0+0x50/0x110 wb_timer_fn+0x227/0x450 ... So rq_qos_wake_function() calls wake_up_process(data->task), which calls try_to_wake_up(), which faults in raw_spin_lock_irqsave(&p->pi_lock). p comes from data->task, and data comes from the waitqueue entry, which is stored on the waiter's stack in rq_qos_wait(). Analyzing the core dump with drgn, I found that the waiter had already woken up and moved on to a completely unrelated code path, clobbering what was previously data->task. Meanwhile, the waker was passing the clobbered garbage in data->task to wake_up_process(), leading to the crash. What's happening is that in between rq_qos_wake_function() deleting the waitqueue entry and calling wake_up_process(), rq_qos_wait() is finding that it already got a token and returning. The race looks like this: rq_qos_wait() rq_qos_wake_function() ============================================================== prepare_to_wait_exclusive() data->got_token = true; list_del_init(&curr->entry); if (data.got_token) break; finish_wait(&rqw->wait, &data.wq); ^- returns immediately because list_empty_careful(&wq_entry->entry) is true ... return, go do something else ... wake_up_process(data->task) (NO LONGER VALID!)-^ Normally, finish_wait() is supposed to synchronize against the waker. But, as noted above, it is returning immediately because the waitqueue entry has already been removed from the waitqueue. The bug is that rq_qos_wake_function() is accessing the waitqueue entry AFTER deleting it. Note that autoremove_wake_function() wakes the waiter and THEN deletes the waitqueue entry, which is the proper order. Fix it by swapping the order. We also need to use list_del_init_careful() to match the list_empty_careful() in finish_wait().

In the Linux kernel, the following vulnerability has been resolved: workqueue: Fix spruious data race in __flush_work() When flushing a work item for cancellation, __flush_work() knows that it exclusively owns the work item through its PENDING bit. 134874e2eee9 ("workqueue: Allow cancel_work_sync() and disable_work() from atomic contexts on BH work items") added a read of @work->data to determine whether to use busy wait for BH work items that are being canceled. While the read is safe when @from_cancel, @work->data was read before testing @from_cancel to simplify code structure: data = *work_data_bits(work); if (from_cancel && !WARN_ON_ONCE(data & WORK_STRUCT_PWQ) && (data & WORK_OFFQ_BH)) { While the read data was never used if !@from_cancel, this could trigger KCSAN data race detection spuriously: ================================================================== BUG: KCSAN: data-race in __flush_work / __flush_work write to 0xffff8881223aa3e8 of 8 bytes by task 3998 on cpu 0: instrument_write include/linux/instrumented.h:41 [inline] ___set_bit include/asm-generic/bitops/instrumented-non-atomic.h:28 [inline] insert_wq_barrier kernel/workqueue.c:3790 [inline] start_flush_work kernel/workqueue.c:4142 [inline] __flush_work+0x30b/0x570 kernel/workqueue.c:4178 flush_work kernel/workqueue.c:4229 [inline] ... read to 0xffff8881223aa3e8 of 8 bytes by task 50 on cpu 1: __flush_work+0x42a/0x570 kernel/workqueue.c:4188 flush_work kernel/workqueue.c:4229 [inline] flush_delayed_work+0x66/0x70 kernel/workqueue.c:4251 ... value changed: 0x0000000000400000 -> 0xffff88810006c00d Reorganize the code so that @from_cancel is tested before @work->data is accessed. The only problem is triggering KCSAN detection spuriously. This shouldn't need READ_ONCE() or other access qualifiers. No functional changes.

In the Linux kernel, the following vulnerability has been resolved: mptcp: pm: fix ID 0 endp usage after multiple re-creations 'local_addr_used' and 'add_addr_accepted' are decremented for addresses not related to the initial subflow (ID0), because the source and destination addresses of the initial subflows are known from the beginning: they don't count as "additional local address being used" or "ADD_ADDR being accepted". It is then required not to increment them when the entrypoint used by the initial subflow is removed and re-added during a connection. Without this modification, this entrypoint cannot be removed and re-added more than once.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Avoid race between dcn35_set_drr() and dc_state_destruct() dc_state_destruct() nulls the resource context of the DC state. The pipe context passed to dcn35_set_drr() is a member of this resource context. If dc_state_destruct() is called parallel to the IRQ processing (which calls dcn35_set_drr() at some point), we can end up using already nulled function callback fields of struct stream_resource. The logic in dcn35_set_drr() already tries to avoid this, by checking tg against NULL. But if the nulling happens exactly after the NULL check and before the next access, then we get a race. Avoid this by copying tg first to a local variable, and then use this variable for all the operations. This should work, as long as nobody frees the resource pool where the timing generators live. (cherry picked from commit 0607a50c004798a96e62c089a4c34c220179dcb5)

In the Linux kernel, the following vulnerability has been resolved: ethtool: check device is present when getting link settings A sysfs reader can race with a device reset or removal, attempting to read device state when the device is not actually present. eg: [exception RIP: qed_get_current_link+17] #8 [ffffb9e4f2907c48] qede_get_link_ksettings at ffffffffc07a994a [qede] #9 [ffffb9e4f2907cd8] __rh_call_get_link_ksettings at ffffffff992b01a3 #10 [ffffb9e4f2907d38] __ethtool_get_link_ksettings at ffffffff992b04e4 #11 [ffffb9e4f2907d90] duplex_show at ffffffff99260300 #12 [ffffb9e4f2907e38] dev_attr_show at ffffffff9905a01c #13 [ffffb9e4f2907e50] sysfs_kf_seq_show at ffffffff98e0145b #14 [ffffb9e4f2907e68] seq_read at ffffffff98d902e3 #15 [ffffb9e4f2907ec8] vfs_read at ffffffff98d657d1 #16 [ffffb9e4f2907f00] ksys_read at ffffffff98d65c3f #17 [ffffb9e4f2907f38] do_syscall_64 at ffffffff98a052fb crash> struct net_device.state ffff9a9d21336000 state = 5, state 5 is __LINK_STATE_START (0b1) and __LINK_STATE_NOCARRIER (0b100). The device is not present, note lack of __LINK_STATE_PRESENT (0b10). This is the same sort of panic as observed in commit 4224cfd7fb65 ("net-sysfs: add check for netdevice being present to speed_show"). There are many other callers of __ethtool_get_link_ksettings() which don't have a device presence check. Move this check into ethtool to protect all callers.

In the Linux kernel, the following vulnerability has been resolved: isdn: mISDN: netjet: Fix crash in nj_probe: 'nj_setup' in netjet.c might fail with -EIO and in this case 'card->irq' is initialized and is bigger than zero. A subsequent call to 'nj_release' will free the irq that has not been requested. Fix this bug by deleting the previous assignment to 'card->irq' and just keep the assignment before 'request_irq'. The KASAN's log reveals it: [ 3.354615 ] WARNING: CPU: 0 PID: 1 at kernel/irq/manage.c:1826 free_irq+0x100/0x480 [ 3.355112 ] Modules linked in: [ 3.355310 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc1-00144-g25a1298726e #13 [ 3.355816 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 3.356552 ] RIP: 0010:free_irq+0x100/0x480 [ 3.356820 ] Code: 6e 08 74 6f 4d 89 f4 e8 5e ac 09 00 4d 8b 74 24 18 4d 85 f6 75 e3 e8 4f ac 09 00 8b 75 c8 48 c7 c7 78 c1 2e 85 e8 e0 cf f5 ff <0f> 0b 48 8b 75 c0 4c 89 ff e8 72 33 0b 03 48 8b 43 40 4c 8b a0 80 [ 3.358012 ] RSP: 0000:ffffc90000017b48 EFLAGS: 00010082 [ 3.358357 ] RAX: 0000000000000000 RBX: ffff888104dc8000 RCX: 0000000000000000 [ 3.358814 ] RDX: ffff8881003c8000 RSI: ffffffff8124a9e6 RDI: 00000000ffffffff [ 3.359272 ] RBP: ffffc90000017b88 R08: 0000000000000000 R09: 0000000000000000 [ 3.359732 ] R10: ffffc900000179f0 R11: 0000000000001d04 R12: 0000000000000000 [ 3.360195 ] R13: ffff888107dc6000 R14: ffff888107dc6928 R15: ffff888104dc80a8 [ 3.360652 ] FS: 0000000000000000(0000) GS:ffff88817bc00000(0000) knlGS:0000000000000000 [ 3.361170 ] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 3.361538 ] CR2: 0000000000000000 CR3: 000000000582e000 CR4: 00000000000006f0 [ 3.362003 ] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 3.362175 ] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 3.362175 ] Call Trace: [ 3.362175 ] nj_release+0x51/0x1e0 [ 3.362175 ] nj_probe+0x450/0x950 [ 3.362175 ] ? pci_device_remove+0x110/0x110 [ 3.362175 ] local_pci_probe+0x45/0xa0 [ 3.362175 ] pci_device_probe+0x12b/0x1d0 [ 3.362175 ] really_probe+0x2a9/0x610 [ 3.362175 ] driver_probe_device+0x90/0x1d0 [ 3.362175 ] ? mutex_lock_nested+0x1b/0x20 [ 3.362175 ] device_driver_attach+0x68/0x70 [ 3.362175 ] __driver_attach+0x124/0x1b0 [ 3.362175 ] ? device_driver_attach+0x70/0x70 [ 3.362175 ] bus_for_each_dev+0xbb/0x110 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] driver_attach+0x27/0x30 [ 3.362175 ] bus_add_driver+0x1eb/0x2a0 [ 3.362175 ] driver_register+0xa9/0x180 [ 3.362175 ] __pci_register_driver+0x82/0x90 [ 3.362175 ] ? w6692_init+0x38/0x38 [ 3.362175 ] nj_init+0x36/0x38 [ 3.362175 ] do_one_initcall+0x7f/0x3d0 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] ? rcu_read_lock_sched_held+0x4f/0x80 [ 3.362175 ] kernel_init_freeable+0x2aa/0x301 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] kernel_init+0x18/0x190 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ret_from_fork+0x1f/0x30 [ 3.362175 ] Kernel panic - not syncing: panic_on_warn set ... [ 3.362175 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc1-00144-g25a1298726e #13 [ 3.362175 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 3.362175 ] Call Trace: [ 3.362175 ] dump_stack+0xba/0xf5 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] panic+0x15a/0x3f2 [ 3.362175 ] ? __warn+0xf2/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] __warn+0x108/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] report_bug+0x119/0x1c0 [ 3.362175 ] handle_bug+0x3b/0x80 [ 3.362175 ] exc_invalid_op+0x18/0x70 [ 3.362175 ] asm_exc_invalid_op+0x12/0x20 [ 3.362175 ] RIP: 0010:free_irq+0x100 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: btrfs: use latest_dev in btrfs_show_devname The test case btrfs/238 reports the warning below: WARNING: CPU: 3 PID: 481 at fs/btrfs/super.c:2509 btrfs_show_devname+0x104/0x1e8 [btrfs] CPU: 2 PID: 1 Comm: systemd Tainted: G W O 5.14.0-rc1-custom #72 Hardware name: QEMU QEMU Virtual Machine, BIOS 0.0.0 02/06/2015 Call trace: btrfs_show_devname+0x108/0x1b4 [btrfs] show_mountinfo+0x234/0x2c4 m_show+0x28/0x34 seq_read_iter+0x12c/0x3c4 vfs_read+0x29c/0x2c8 ksys_read+0x80/0xec __arm64_sys_read+0x28/0x34 invoke_syscall+0x50/0xf8 do_el0_svc+0x88/0x138 el0_svc+0x2c/0x8c el0t_64_sync_handler+0x84/0xe4 el0t_64_sync+0x198/0x19c Reason: While btrfs_prepare_sprout() moves the fs_devices::devices into fs_devices::seed_list, the btrfs_show_devname() searches for the devices and found none, leading to the warning as in above. Fix: latest_dev is updated according to the changes to the device list. That means we could use the latest_dev->name to show the device name in /proc/self/mounts, the pointer will be always valid as it's assigned before the device is deleted from the list in remove or replace. The RCU protection is sufficient as the device structure is freed after synchronization.

In the Linux kernel, the following vulnerability has been resolved: udp: fix race between close() and udp_abort() Kaustubh reported and diagnosed a panic in udp_lib_lookup(). The root cause is udp_abort() racing with close(). Both racing functions acquire the socket lock, but udp{v6}_destroy_sock() release it before performing destructive actions. We can't easily extend the socket lock scope to avoid the race, instead use the SOCK_DEAD flag to prevent udp_abort from doing any action when the critical race happens. Diagnosed-and-tested-by: Kaustubh Pandey <kapandey@codeaurora.org>

In the Linux kernel, the following vulnerability has been resolved: ALSA: line6: Fix racy access to midibuf There can be concurrent accesses to line6 midibuf from both the URB completion callback and the rawmidi API access. This could be a cause of KMSAN warning triggered by syzkaller below (so put as reported-by here). This patch protects the midibuf call of the former code path with a spinlock for avoiding the possible races.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Always drain health in shutdown callback There is no point in recovery during device shutdown. if health work started need to wait for it to avoid races and NULL pointer access. Hence, drain health WQ on shutdown callback.

In the Linux kernel, the following vulnerability has been resolved: memcg: protect concurrent access to mem_cgroup_idr Commit 73f576c04b94 ("mm: memcontrol: fix cgroup creation failure after many small jobs") decoupled the memcg IDs from the CSS ID space to fix the cgroup creation failures. It introduced IDR to maintain the memcg ID space. The IDR depends on external synchronization mechanisms for modifications. For the mem_cgroup_idr, the idr_alloc() and idr_replace() happen within css callback and thus are protected through cgroup_mutex from concurrent modifications. However idr_remove() for mem_cgroup_idr was not protected against concurrency and can be run concurrently for different memcgs when they hit their refcnt to zero. Fix that. We have been seeing list_lru based kernel crashes at a low frequency in our fleet for a long time. These crashes were in different part of list_lru code including list_lru_add(), list_lru_del() and reparenting code. Upon further inspection, it looked like for a given object (dentry and inode), the super_block's list_lru didn't have list_lru_one for the memcg of that object. The initial suspicions were either the object is not allocated through kmem_cache_alloc_lru() or somehow memcg_list_lru_alloc() failed to allocate list_lru_one() for a memcg but returned success. No evidence were found for these cases. Looking more deeply, we started seeing situations where valid memcg's id is not present in mem_cgroup_idr and in some cases multiple valid memcgs have same id and mem_cgroup_idr is pointing to one of them. So, the most reasonable explanation is that these situations can happen due to race between multiple idr_remove() calls or race between idr_alloc()/idr_replace() and idr_remove(). These races are causing multiple memcgs to acquire the same ID and then offlining of one of them would cleanup list_lrus on the system for all of them. Later access from other memcgs to the list_lru cause crashes due to missing list_lru_one.

In the Linux kernel, the following vulnerability has been resolved: net/tcp: Disable TCP-AO static key after RCU grace period The lifetime of TCP-AO static_key is the same as the last tcp_ao_info. On the socket destruction tcp_ao_info ceases to be with RCU grace period, while tcp-ao static branch is currently deferred destructed. The static key definition is : DEFINE_STATIC_KEY_DEFERRED_FALSE(tcp_ao_needed, HZ); which means that if RCU grace period is delayed by more than a second and tcp_ao_needed is in the process of disablement, other CPUs may yet see tcp_ao_info which atent dead, but soon-to-be. And that breaks the assumption of static_key_fast_inc_not_disabled(). See the comment near the definition: > * The caller must make sure that the static key can't get disabled while > * in this function. It doesn't patch jump labels, only adds a user to > * an already enabled static key. Originally it was introduced in commit eb8c507296f6 ("jump_label: Prevent key->enabled int overflow"), which is needed for the atomic contexts, one of which would be the creation of a full socket from a request socket. In that atomic context, it's known by the presence of the key (md5/ao) that the static branch is already enabled. So, the ref counter for that static branch is just incremented instead of holding the proper mutex. static_key_fast_inc_not_disabled() is just a helper for such usage case. But it must not be used if the static branch could get disabled in parallel as it's not protected by jump_label_mutex and as a result, races with jump_label_update() implementation details. Happened on netdev test-bot[1], so not a theoretical issue: [] jump_label: Fatal kernel bug, unexpected op at tcp_inbound_hash+0x1a7/0x870 [ffffffffa8c4e9b7] (eb 50 0f 1f 44 != 66 90 0f 1f 00)) size:2 type:1 [] ------------[ cut here ]------------ [] kernel BUG at arch/x86/kernel/jump_label.c:73! [] Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI [] CPU: 3 PID: 243 Comm: kworker/3:3 Not tainted 6.10.0-virtme #1 [] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 [] Workqueue: events jump_label_update_timeout [] RIP: 0010:__jump_label_patch+0x2f6/0x350 ... [] Call Trace: [] <TASK> [] arch_jump_label_transform_queue+0x6c/0x110 [] __jump_label_update+0xef/0x350 [] __static_key_slow_dec_cpuslocked.part.0+0x3c/0x60 [] jump_label_update_timeout+0x2c/0x40 [] process_one_work+0xe3b/0x1670 [] worker_thread+0x587/0xce0 [] kthread+0x28a/0x350 [] ret_from_fork+0x31/0x70 [] ret_from_fork_asm+0x1a/0x30 [] </TASK> [] Modules linked in: veth [] ---[ end trace 0000000000000000 ]--- [] RIP: 0010:__jump_label_patch+0x2f6/0x350 [1]: https://netdev-3.bots.linux.dev/vmksft-tcp-ao-dbg/results/696681/5-connect-deny-ipv6/stderr

In the Linux kernel, the following vulnerability has been resolved: nvmet: fix a possible leak when destroy a ctrl during qp establishment In nvmet_sq_destroy we capture sq->ctrl early and if it is non-NULL we know that a ctrl was allocated (in the admin connect request handler) and we need to release pending AERs, clear ctrl->sqs and sq->ctrl (for nvme-loop primarily), and drop the final reference on the ctrl. However, a small window is possible where nvmet_sq_destroy starts (as a result of the client giving up and disconnecting) concurrently with the nvme admin connect cmd (which may be in an early stage). But *before* kill_and_confirm of sq->ref (i.e. the admin connect managed to get an sq live reference). In this case, sq->ctrl was allocated however after it was captured in a local variable in nvmet_sq_destroy. This prevented the final reference drop on the ctrl. Solve this by re-capturing the sq->ctrl after all inflight request has completed, where for sure sq->ctrl reference is final, and move forward based on that. This issue was observed in an environment with many hosts connecting multiple ctrls simoutanuosly, creating a delay in allocating a ctrl leading up to this race window.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix overlapping copy within dml_core_mode_programming [WHY] &mode_lib->mp.Watermark and &locals->Watermark are the same address. memcpy may lead to unexpected behavior. [HOW] memmove should be used.

In the Linux kernel, the following vulnerability has been resolved: Revert "mm/writeback: fix possible divide-by-zero in wb_dirty_limits(), again" Patch series "mm: Avoid possible overflows in dirty throttling". Dirty throttling logic assumes dirty limits in page units fit into 32-bits. This patch series makes sure this is true (see patch 2/2 for more details). This patch (of 2): This reverts commit 9319b647902cbd5cc884ac08a8a6d54ce111fc78. The commit is broken in several ways. Firstly, the removed (u64) cast from the multiplication will introduce a multiplication overflow on 32-bit archs if wb_thresh * bg_thresh >= 1<<32 (which is actually common - the default settings with 4GB of RAM will trigger this). Secondly, the div64_u64() is unnecessarily expensive on 32-bit archs. We have div64_ul() in case we want to be safe & cheap. Thirdly, if dirty thresholds are larger than 1<<32 pages, then dirty balancing is going to blow up in many other spectacular ways anyway so trying to fix one possible overflow is just moot.

Race condition in ip_vs_conn_flush in Linux 2.6 before 2.6.13 and 2.4 before 2.4.32-pre2, when running on SMP systems, allows local users to cause a denial of service (null dereference) by causing a connection timer to expire while the connection table is being flushed before the appropriate lock is acquired.

In the Linux kernel, the following vulnerability has been resolved: soc: qcom: pmic_glink: Fix race during initialization As pointed out by Stephen Boyd it is possible that during initialization of the pmic_glink child drivers, the protection-domain notifiers fires, and the associated work is scheduled, before the client registration returns and as a result the local "client" pointer has been initialized. The outcome of this is a NULL pointer dereference as the "client" pointer is blindly dereferenced. Timeline provided by Stephen: CPU0 CPU1 ---- ---- ucsi->client = NULL; devm_pmic_glink_register_client() client->pdr_notify(client->priv, pg->client_state) pmic_glink_ucsi_pdr_notify() schedule_work(&ucsi->register_work) <schedule away> pmic_glink_ucsi_register() ucsi_register() pmic_glink_ucsi_read_version() pmic_glink_ucsi_read() pmic_glink_ucsi_read() pmic_glink_send(ucsi->client) <client is NULL BAD> ucsi->client = client // Too late! This code is identical across the altmode, battery manager and usci child drivers. Resolve this by splitting the allocation of the "client" object and the registration thereof into two operations. This only happens if the protection domain registry is populated at the time of registration, which by the introduction of commit '1ebcde047c54 ("soc: qcom: add pd-mapper implementation")' became much more likely.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Disable DMCUB timeout for DCN35 [Why] DMCUB can intermittently take longer than expected to process commands. Old ASIC policy was to continue while logging a diagnostic error - which works fine for ASIC without IPS, but with IPS this could lead to a race condition where we attempt to access DCN state while it's inaccessible, leading to a system hang when the NIU port is not disabled or register accesses that timeout and the display configuration in an undefined state. [How] We need to investigate why these accesses take longer than expected, but for now we should disable the timeout on DCN35 to avoid this race condition. Since the waits happen only at lower interrupt levels the risk of taking too long at higher IRQ and causing a system watchdog timeout are minimal.

In the Linux kernel, the following vulnerability has been resolved: ip: Fix data-races around sysctl_ip_prot_sock. sysctl_ip_prot_sock is accessed concurrently, and there is always a chance of data-race. So, all readers and writers need some basic protection to avoid load/store-tearing.

In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: Wait unconditionally after issuing EndXfer command Currently all controller IP/revisions except DWC3_usb3 >= 310a wait 1ms unconditionally for ENDXFER completion when IOC is not set. This is because DWC_usb3 controller revisions >= 3.10a supports GUCTL2[14: Rst_actbitlater] bit which allows polling CMDACT bit to know whether ENDXFER command is completed. Consider a case where an IN request was queued, and parallelly soft_disconnect was called (due to ffs_epfile_release). This eventually calls stop_active_transfer with IOC cleared, hence send_gadget_ep_cmd() skips waiting for CMDACT cleared during EndXfer. For DWC3 controllers with revisions >= 310a, we don't forcefully wait for 1ms either, and we proceed by unmapping the requests. If ENDXFER didn't complete by this time, it leads to SMMU faults since the controller would still be accessing those requests. Fix this by ensuring ENDXFER completion by adding 1ms delay in __dwc3_stop_active_transfer() unconditionally.

In the Linux kernel, the following vulnerability has been resolved: lib/generic-radix-tree.c: Fix rare race in __genradix_ptr_alloc() If we need to increase the tree depth, allocate a new node, and then race with another thread that increased the tree depth before us, we'll still have a preallocated node that might be used later. If we then use that node for a new non-root node, it'll still have a pointer to the old root instead of being zeroed - fix this by zeroing it in the cmpxchg failure path.

In the Linux kernel, the following vulnerability has been resolved: drm/msm/dp: do not complete dp_aux_cmd_fifo_tx() if irq is not for aux transfer There are 3 possible interrupt sources are handled by DP controller, HPDstatus, Controller state changes and Aux read/write transaction. At every irq, DP controller have to check isr status of every interrupt sources and service the interrupt if its isr status bits shows interrupts are pending. There is potential race condition may happen at current aux isr handler implementation since it is always complete dp_aux_cmd_fifo_tx() even irq is not for aux read or write transaction. This may cause aux read transaction return premature if host aux data read is in the middle of waiting for sink to complete transferring data to host while irq happen. This will cause host's receiving buffer contains unexpected data. This patch fixes this problem by checking aux isr and return immediately at aux isr handler if there are no any isr status bits set. Current there is a bug report regrading eDP edid corruption happen during system booting up. After lengthy debugging to found that VIDEO_READY interrupt was continuously firing during system booting up which cause dp_aux_isr() to complete dp_aux_cmd_fifo_tx() prematurely to retrieve data from aux hardware buffer which is not yet contains complete data transfer from sink. This cause edid corruption. Follows are the signature at kernel logs when problem happen, EDID has corrupt header panel-simple-dp-aux aux-aea0000.edp: Couldn't identify panel via EDID Changes in v2: -- do complete if (ret == IRQ_HANDLED) ay dp-aux_isr() -- add more commit text Changes in v3: -- add Stephen suggested -- dp_aux_isr() return IRQ_XXX back to caller -- dp_ctrl_isr() return IRQ_XXX back to caller Changes in v4: -- split into two patches Changes in v5: -- delete empty line between tags Changes in v6: -- remove extra "that" and fixed line more than 75 char at commit text Patchwork: https://patchwork.freedesktop.org/patch/516121/

In the Linux kernel, the following vulnerability has been resolved: platform/chrome: cros_ec_uart: properly fix race condition The cros_ec_uart_probe() function calls devm_serdev_device_open() before it calls serdev_device_set_client_ops(). This can trigger a NULL pointer dereference: BUG: kernel NULL pointer dereference, address: 0000000000000000 ... Call Trace: <TASK> ... ? ttyport_receive_buf A simplified version of crashing code is as follows: static inline size_t serdev_controller_receive_buf(struct serdev_controller *ctrl, const u8 *data, size_t count) { struct serdev_device *serdev = ctrl->serdev; if (!serdev || !serdev->ops->receive_buf) // CRASH! return 0; return serdev->ops->receive_buf(serdev, data, count); } It assumes that if SERPORT_ACTIVE is set and serdev exists, serdev->ops will also exist. This conflicts with the existing cros_ec_uart_probe() logic, as it first calls devm_serdev_device_open() (which sets SERPORT_ACTIVE), and only later sets serdev->ops via serdev_device_set_client_ops(). Commit 01f95d42b8f4 ("platform/chrome: cros_ec_uart: fix race condition") attempted to fix a similar race condition, but while doing so, made the window of error for this race condition to happen much wider. Attempt to fix the race condition again, making sure we fully setup before calling devm_serdev_device_open().

A memory leak in the sdma_init() function in drivers/infiniband/hw/hfi1/sdma.c in the Linux kernel before 5.3.9 allows attackers to cause a denial of service (memory consumption) by triggering rhashtable_init() failures, aka CID-34b3be18a04e. NOTE: This has been disputed as not a vulnerability because "rhashtable_init() can only fail if it is passed invalid values in the second parameter's struct, but when invoked from sdma_init() that is a pointer to a static const struct, so an attacker could only trigger failure if they could corrupt kernel memory (in which case a small memory leak is not a significant problem).

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: pick the version of SESSION_PROTECTION_NOTIF When we want to know whether we should look for the mac_id or the link_id in struct iwl_mvm_session_prot_notif, we should look at the version of SESSION_PROTECTION_NOTIF. This causes WARNINGs: WARNING: CPU: 0 PID: 11403 at drivers/net/wireless/intel/iwlwifi/mvm/time-event.c:959 iwl_mvm_rx_session_protect_notif+0x333/0x340 [iwlmvm] RIP: 0010:iwl_mvm_rx_session_protect_notif+0x333/0x340 [iwlmvm] Code: 00 49 c7 84 24 48 07 00 00 00 00 00 00 41 c6 84 24 78 07 00 00 ff 4c 89 f7 e8 e9 71 54 d9 e9 7d fd ff ff 0f 0b e9 23 fe ff ff <0f> 0b e9 1c fe ff ff 66 0f 1f 44 00 00 90 90 90 90 90 90 90 90 90 RSP: 0018:ffffb4bb00003d40 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffff9ae63a361000 RCX: ffff9ae4a98b60d4 RDX: ffff9ae4588499c0 RSI: 0000000000000305 RDI: ffff9ae4a98b6358 RBP: ffffb4bb00003d68 R08: 0000000000000003 R09: 0000000000000010 R10: ffffb4bb00003d00 R11: 000000000000000f R12: ffff9ae441399050 R13: ffff9ae4761329e8 R14: 0000000000000001 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff9ae7af400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055fb75680018 CR3: 00000003dae32006 CR4: 0000000000f70ef0 PKRU: 55555554 Call Trace: <IRQ> ? show_regs+0x69/0x80 ? __warn+0x8d/0x150 ? iwl_mvm_rx_session_protect_notif+0x333/0x340 [iwlmvm] ? report_bug+0x196/0x1c0 ? handle_bug+0x45/0x80 ? exc_invalid_op+0x1c/0xb0 ? asm_exc_invalid_op+0x1f/0x30 ? iwl_mvm_rx_session_protect_notif+0x333/0x340 [iwlmvm] iwl_mvm_rx_common+0x115/0x340 [iwlmvm] iwl_mvm_rx_mq+0xa6/0x100 [iwlmvm] iwl_pcie_rx_handle+0x263/0xa10 [iwlwifi] iwl_pcie_napi_poll_msix+0x32/0xd0 [iwlwifi]

In the Linux kernel, the following vulnerability has been resolved: PCI: of_property: Return error for int_map allocation failure Return -ENOMEM from of_pci_prop_intr_map() if kcalloc() fails to prevent a NULL pointer dereference in this case. [bhelgaas: commit log]

An issue was discovered in the Linux kernel before 5.11.7. usbip_sockfd_store in drivers/usb/usbip/stub_dev.c allows attackers to cause a denial of service (GPF) because the stub-up sequence has race conditions during an update of the local and shared status, aka CID-9380afd6df70.

A race condition was discovered in get_old_root in fs/btrfs/ctree.c in the Linux kernel through 5.11.8. It allows attackers to cause a denial of service (BUG) because of a lack of locking on an extent buffer before a cloning operation, aka CID-dbcc7d57bffc.

In the Linux kernel, the following vulnerability has been resolved: wireguard: receive: annotate data-race around receiving_counter.counter Syzkaller with KCSAN identified a data-race issue when accessing keypair->receiving_counter.counter. Use READ_ONCE() and WRITE_ONCE() annotations to mark the data race as intentional. BUG: KCSAN: data-race in wg_packet_decrypt_worker / wg_packet_rx_poll write to 0xffff888107765888 of 8 bytes by interrupt on cpu 0: counter_validate drivers/net/wireguard/receive.c:321 [inline] wg_packet_rx_poll+0x3ac/0xf00 drivers/net/wireguard/receive.c:461 __napi_poll+0x60/0x3b0 net/core/dev.c:6536 napi_poll net/core/dev.c:6605 [inline] net_rx_action+0x32b/0x750 net/core/dev.c:6738 __do_softirq+0xc4/0x279 kernel/softirq.c:553 do_softirq+0x5e/0x90 kernel/softirq.c:454 __local_bh_enable_ip+0x64/0x70 kernel/softirq.c:381 __raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline] _raw_spin_unlock_bh+0x36/0x40 kernel/locking/spinlock.c:210 spin_unlock_bh include/linux/spinlock.h:396 [inline] ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline] wg_packet_decrypt_worker+0x6c5/0x700 drivers/net/wireguard/receive.c:499 process_one_work kernel/workqueue.c:2633 [inline] ... read to 0xffff888107765888 of 8 bytes by task 3196 on cpu 1: decrypt_packet drivers/net/wireguard/receive.c:252 [inline] wg_packet_decrypt_worker+0x220/0x700 drivers/net/wireguard/receive.c:501 process_one_work kernel/workqueue.c:2633 [inline] process_scheduled_works+0x5b8/0xa30 kernel/workqueue.c:2706 worker_thread+0x525/0x730 kernel/workqueue.c:2787 ...

In the Linux kernel, the following vulnerability has been resolved: hv_netvsc: Fix race condition between netvsc_probe and netvsc_remove In commit ac5047671758 ("hv_netvsc: Disable NAPI before closing the VMBus channel"), napi_disable was getting called for all channels, including all subchannels without confirming if they are enabled or not. This caused hv_netvsc getting hung at napi_disable, when netvsc_probe() has finished running but nvdev->subchan_work has not started yet. netvsc_subchan_work() -> rndis_set_subchannel() has not created the sub-channels and because of that netvsc_sc_open() is not running. netvsc_remove() calls cancel_work_sync(&nvdev->subchan_work), for which netvsc_subchan_work did not run. netif_napi_add() sets the bit NAPI_STATE_SCHED because it ensures NAPI cannot be scheduled. Then netvsc_sc_open() -> napi_enable will clear the NAPIF_STATE_SCHED bit, so it can be scheduled. napi_disable() does the opposite. Now during netvsc_device_remove(), when napi_disable is called for those subchannels, napi_disable gets stuck on infinite msleep. This fix addresses this problem by ensuring that napi_disable() is not getting called for non-enabled NAPI struct. But netif_napi_del() is still necessary for these non-enabled NAPI struct for cleanup purpose. Call trace: [ 654.559417] task:modprobe state:D stack: 0 pid: 2321 ppid: 1091 flags:0x00004002 [ 654.568030] Call Trace: [ 654.571221] <TASK> [ 654.573790] __schedule+0x2d6/0x960 [ 654.577733] schedule+0x69/0xf0 [ 654.581214] schedule_timeout+0x87/0x140 [ 654.585463] ? __bpf_trace_tick_stop+0x20/0x20 [ 654.590291] msleep+0x2d/0x40 [ 654.593625] napi_disable+0x2b/0x80 [ 654.597437] netvsc_device_remove+0x8a/0x1f0 [hv_netvsc] [ 654.603935] rndis_filter_device_remove+0x194/0x1c0 [hv_netvsc] [ 654.611101] ? do_wait_intr+0xb0/0xb0 [ 654.615753] netvsc_remove+0x7c/0x120 [hv_netvsc] [ 654.621675] vmbus_remove+0x27/0x40 [hv_vmbus]

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to truncate meta inode pages forcely Below race case can cause data corruption: Thread A GC thread - gc_data_segment - ra_data_block - locked meta_inode page - f2fs_inplace_write_data - invalidate_mapping_pages : fail to invalidate meta_inode page due to lock failure or dirty|writeback status - f2fs_submit_page_bio : write last dirty data to old blkaddr - move_data_block - load old data from meta_inode page - f2fs_submit_page_write : write old data to new blkaddr Because invalidate_mapping_pages() will skip invalidating page which has unclear status including locked, dirty, writeback and so on, so we need to use truncate_inode_pages_range() instead of invalidate_mapping_pages() to make sure meta_inode page will be dropped.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Add 'replay' NULL check in 'edp_set_replay_allow_active()' In the first if statement, we're checking if 'replay' is NULL. But in the second if statement, we're not checking if 'replay' is NULL again before calling replay->funcs->replay_set_power_opt(). if (replay == NULL && force_static) return false; ... if (link->replay_settings.replay_feature_enabled && replay->funcs->replay_set_power_opt) { replay->funcs->replay_set_power_opt(replay, *power_opts, panel_inst); link->replay_settings.replay_power_opt_active = *power_opts; } If 'replay' is NULL, this will cause a null pointer dereference. Fixes the below found by smatch: drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_edp_panel_control.c:895 edp_set_replay_allow_active() error: we previously assumed 'replay' could be null (see line 887)

In the Linux kernel, the following vulnerability has been resolved: tls: fix race between tx work scheduling and socket close Similarly to previous commit, the submitting thread (recvmsg/sendmsg) may exit as soon as the async crypto handler calls complete(). Reorder scheduling the work before calling complete(). This seems more logical in the first place, as it's the inverse order of what the submitting thread will do.