In the Linux kernel, the following vulnerability has been resolved: ocfs2: remove unreasonable unlock in ocfs2_read_blocks Patch series "Misc fixes for ocfs2_read_blocks", v5. This series contains 2 fixes for ocfs2_read_blocks(). The first patch fix the issue reported by syzbot, which detects bad unlock balance in ocfs2_read_blocks(). The second patch fixes an issue reported by Heming Zhao when reviewing above fix. This patch (of 2): There was a lock release before exiting, so remove the unreasonable unlock.

In the Linux kernel, the following vulnerability has been resolved: KVM: Use dedicated mutex to protect kvm_usage_count to avoid deadlock Use a dedicated mutex to guard kvm_usage_count to fix a potential deadlock on x86 due to a chain of locks and SRCU synchronizations. Translating the below lockdep splat, CPU1 #6 will wait on CPU0 #1, CPU0 #8 will wait on CPU2 #3, and CPU2 #7 will wait on CPU1 #4 (if there's a writer, due to the fairness of r/w semaphores). CPU0 CPU1 CPU2 1 lock(&kvm->slots_lock); 2 lock(&vcpu->mutex); 3 lock(&kvm->srcu); 4 lock(cpu_hotplug_lock); 5 lock(kvm_lock); 6 lock(&kvm->slots_lock); 7 lock(cpu_hotplug_lock); 8 sync(&kvm->srcu); Note, there are likely more potential deadlocks in KVM x86, e.g. the same pattern of taking cpu_hotplug_lock outside of kvm_lock likely exists with __kvmclock_cpufreq_notifier(): cpuhp_cpufreq_online() | -> cpufreq_online() | -> cpufreq_gov_performance_limits() | -> __cpufreq_driver_target() | -> __target_index() | -> cpufreq_freq_transition_begin() | -> cpufreq_notify_transition() | -> ... __kvmclock_cpufreq_notifier() But, actually triggering such deadlocks is beyond rare due to the combination of dependencies and timings involved. E.g. the cpufreq notifier is only used on older CPUs without a constant TSC, mucking with the NX hugepage mitigation while VMs are running is very uncommon, and doing so while also onlining/offlining a CPU (necessary to generate contention on cpu_hotplug_lock) would be even more unusual. The most robust solution to the general cpu_hotplug_lock issue is likely to switch vm_list to be an RCU-protected list, e.g. so that x86's cpufreq notifier doesn't to take kvm_lock. For now, settle for fixing the most blatant deadlock, as switching to an RCU-protected list is a much more involved change, but add a comment in locking.rst to call out that care needs to be taken when walking holding kvm_lock and walking vm_list. ====================================================== WARNING: possible circular locking dependency detected 6.10.0-smp--c257535a0c9d-pip #330 Tainted: G S O ------------------------------------------------------ tee/35048 is trying to acquire lock: ff6a80eced71e0a8 (&kvm->slots_lock){+.+.}-{3:3}, at: set_nx_huge_pages+0x179/0x1e0 [kvm] but task is already holding lock: ffffffffc07abb08 (kvm_lock){+.+.}-{3:3}, at: set_nx_huge_pages+0x14a/0x1e0 [kvm] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (kvm_lock){+.+.}-{3:3}: __mutex_lock+0x6a/0xb40 mutex_lock_nested+0x1f/0x30 kvm_dev_ioctl+0x4fb/0xe50 [kvm] __se_sys_ioctl+0x7b/0xd0 __x64_sys_ioctl+0x21/0x30 x64_sys_call+0x15d0/0x2e60 do_syscall_64+0x83/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #2 (cpu_hotplug_lock){++++}-{0:0}: cpus_read_lock+0x2e/0xb0 static_key_slow_inc+0x16/0x30 kvm_lapic_set_base+0x6a/0x1c0 [kvm] kvm_set_apic_base+0x8f/0xe0 [kvm] kvm_set_msr_common+0x9ae/0xf80 [kvm] vmx_set_msr+0xa54/0xbe0 [kvm_intel] __kvm_set_msr+0xb6/0x1a0 [kvm] kvm_arch_vcpu_ioctl+0xeca/0x10c0 [kvm] kvm_vcpu_ioctl+0x485/0x5b0 [kvm] __se_sys_ioctl+0x7b/0xd0 __x64_sys_ioctl+0x21/0x30 x64_sys_call+0x15d0/0x2e60 do_syscall_64+0x83/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #1 (&kvm->srcu){.+.+}-{0:0}: __synchronize_srcu+0x44/0x1a0 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: erofs: handle overlapped pclusters out of crafted images properly syzbot reported a task hang issue due to a deadlock case where it is waiting for the folio lock of a cached folio that will be used for cache I/Os. After looking into the crafted fuzzed image, I found it's formed with several overlapped big pclusters as below: Ext: logical offset | length : physical offset | length 0: 0.. 16384 | 16384 : 151552.. 167936 | 16384 1: 16384.. 32768 | 16384 : 155648.. 172032 | 16384 2: 32768.. 49152 | 16384 : 537223168.. 537239552 | 16384 ... Here, extent 0/1 are physically overlapped although it's entirely _impossible_ for normal filesystem images generated by mkfs. First, managed folios containing compressed data will be marked as up-to-date and then unlocked immediately (unlike in-place folios) when compressed I/Os are complete. If physical blocks are not submitted in the incremental order, there should be separate BIOs to avoid dependency issues. However, the current code mis-arranges z_erofs_fill_bio_vec() and BIO submission which causes unexpected BIO waits. Second, managed folios will be connected to their own pclusters for efficient inter-queries. However, this is somewhat hard to implement easily if overlapped big pclusters exist. Again, these only appear in fuzzed images so let's simply fall back to temporary short-lived pages for correctness. Additionally, it justifies that referenced managed folios cannot be truncated for now and reverts part of commit 2080ca1ed3e4 ("erofs: tidy up `struct z_erofs_bvec`") for simplicity although it shouldn't be any difference.

In the Linux kernel, the following vulnerability has been resolved: rtmutex: Drop rt_mutex::wait_lock before scheduling rt_mutex_handle_deadlock() is called with rt_mutex::wait_lock held. In the good case it returns with the lock held and in the deadlock case it emits a warning and goes into an endless scheduling loop with the lock held, which triggers the 'scheduling in atomic' warning. Unlock rt_mutex::wait_lock in the dead lock case before issuing the warning and dropping into the schedule for ever loop. [ tglx: Moved unlock before the WARN(), removed the pointless comment, massaged changelog, added Fixes tag ]

In the Linux kernel, the following vulnerability has been resolved: drm/xe/client: add missing bo locking in show_meminfo() bo_meminfo() wants to inspect bo state like tt and the ttm resource, however this state can change at any point leading to stuff like NPD and UAF, if the bo lock is not held. Grab the bo lock when calling bo_meminfo(), ensuring we drop any spinlocks first. In the case of object_idr we now also need to hold a ref. v2 (MattB) - Also add xe_bo_assert_held() (cherry picked from commit 4f63d712fa104c3ebefcb289d1e733e86d8698c7)

In the Linux kernel, the following vulnerability has been resolved: bonding: change ipsec_lock from spin lock to mutex In the cited commit, bond->ipsec_lock is added to protect ipsec_list, hence xdo_dev_state_add and xdo_dev_state_delete are called inside this lock. As ipsec_lock is a spin lock and such xfrmdev ops may sleep, "scheduling while atomic" will be triggered when changing bond's active slave. [ 101.055189] BUG: scheduling while atomic: bash/902/0x00000200 [ 101.055726] Modules linked in: [ 101.058211] CPU: 3 PID: 902 Comm: bash Not tainted 6.9.0-rc4+ #1 [ 101.058760] Hardware name: [ 101.059434] Call Trace: [ 101.059436] <TASK> [ 101.060873] dump_stack_lvl+0x51/0x60 [ 101.061275] __schedule_bug+0x4e/0x60 [ 101.061682] __schedule+0x612/0x7c0 [ 101.062078] ? __mod_timer+0x25c/0x370 [ 101.062486] schedule+0x25/0xd0 [ 101.062845] schedule_timeout+0x77/0xf0 [ 101.063265] ? asm_common_interrupt+0x22/0x40 [ 101.063724] ? __bpf_trace_itimer_state+0x10/0x10 [ 101.064215] __wait_for_common+0x87/0x190 [ 101.064648] ? usleep_range_state+0x90/0x90 [ 101.065091] cmd_exec+0x437/0xb20 [mlx5_core] [ 101.065569] mlx5_cmd_do+0x1e/0x40 [mlx5_core] [ 101.066051] mlx5_cmd_exec+0x18/0x30 [mlx5_core] [ 101.066552] mlx5_crypto_create_dek_key+0xea/0x120 [mlx5_core] [ 101.067163] ? bonding_sysfs_store_option+0x4d/0x80 [bonding] [ 101.067738] ? kmalloc_trace+0x4d/0x350 [ 101.068156] mlx5_ipsec_create_sa_ctx+0x33/0x100 [mlx5_core] [ 101.068747] mlx5e_xfrm_add_state+0x47b/0xaa0 [mlx5_core] [ 101.069312] bond_change_active_slave+0x392/0x900 [bonding] [ 101.069868] bond_option_active_slave_set+0x1c2/0x240 [bonding] [ 101.070454] __bond_opt_set+0xa6/0x430 [bonding] [ 101.070935] __bond_opt_set_notify+0x2f/0x90 [bonding] [ 101.071453] bond_opt_tryset_rtnl+0x72/0xb0 [bonding] [ 101.071965] bonding_sysfs_store_option+0x4d/0x80 [bonding] [ 101.072567] kernfs_fop_write_iter+0x10c/0x1a0 [ 101.073033] vfs_write+0x2d8/0x400 [ 101.073416] ? alloc_fd+0x48/0x180 [ 101.073798] ksys_write+0x5f/0xe0 [ 101.074175] do_syscall_64+0x52/0x110 [ 101.074576] entry_SYSCALL_64_after_hwframe+0x4b/0x53 As bond_ipsec_add_sa_all and bond_ipsec_del_sa_all are only called from bond_change_active_slave, which requires holding the RTNL lock. And bond_ipsec_add_sa and bond_ipsec_del_sa are xfrm state xdo_dev_state_add and xdo_dev_state_delete APIs, which are in user context. So ipsec_lock doesn't have to be spin lock, change it to mutex, and thus the above issue can be resolved.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/client: fix deadlock in show_meminfo() There is a real deadlock as well as sleeping in atomic() bug in here, if the bo put happens to be the last ref, since bo destruction wants to grab the same spinlock and sleeping locks. Fix that by dropping the ref using xe_bo_put_deferred(), and moving the final commit outside of the lock. Dropping the lock around the put is tricky since the bo can go out of scope and delete itself from the list, making it difficult to navigate to the next list entry. (cherry picked from commit 0083b8e6f11d7662283a267d4ce7c966812ffd8a)

In the Linux kernel, the following vulnerability has been resolved: firmware: qcom: scm: Mark get_wq_ctx() as atomic call Currently get_wq_ctx() is wrongly configured as a standard call. When two SMC calls are in sleep and one SMC wakes up, it calls get_wq_ctx() to resume the corresponding sleeping thread. But if get_wq_ctx() is interrupted, goes to sleep and another SMC call is waiting to be allocated a waitq context, it leads to a deadlock. To avoid this get_wq_ctx() must be an atomic call and can't be a standard SMC call. Hence mark get_wq_ctx() as a fast call.

In the Linux kernel, the following vulnerability has been resolved: can: mcp251x: fix deadlock if an interrupt occurs during mcp251x_open The mcp251x_hw_wake() function is called with the mpc_lock mutex held and disables the interrupt handler so that no interrupts can be processed while waking the device. If an interrupt has already occurred then waiting for the interrupt handler to complete will deadlock because it will be trying to acquire the same mutex. CPU0 CPU1 ---- ---- mcp251x_open() mutex_lock(&priv->mcp_lock) request_threaded_irq() <interrupt> mcp251x_can_ist() mutex_lock(&priv->mcp_lock) mcp251x_hw_wake() disable_irq() <-- deadlock Use disable_irq_nosync() instead because the interrupt handler does everything while holding the mutex so it doesn't matter if it's still running.

An issue was discovered in fs/io_uring.c in the Linux kernel through 5.11.8. It allows attackers to cause a denial of service (deadlock) because exit may be waiting to park a SQPOLL thread, but concurrently that SQPOLL thread is waiting for a signal to start, aka CID-3ebba796fa25.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/preempt_fence: enlarge the fence critical section It is really easy to introduce subtle deadlocks in preempt_fence_work_func() since we operate on single global ordered-wq for signalling our preempt fences behind the scenes, so even though we signal a particular fence, everything in the callback should be in the fence critical section, since blocking in the callback will prevent other published fences from signalling. If we enlarge the fence critical section to cover the entire callback, then lockdep should be able to understand this better, and complain if we grab a sensitive lock like vm->lock, which is also held when waiting on preempt fences.

In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix a deadlock problem when config TC during resetting When config TC during the reset process, may cause a deadlock, the flow is as below: pf reset start │ ▼ ...... setup tc │ │ ▼ ▼ DOWN: napi_disable() napi_disable()(skip) │ │ │ ▼ ▼ ...... ...... │ │ ▼ │ napi_enable() │ ▼ UINIT: netif_napi_del() │ ▼ ...... │ ▼ INIT: netif_napi_add() │ ▼ ...... global reset start │ │ ▼ ▼ UP: napi_enable()(skip) ...... │ │ ▼ ▼ ...... napi_disable() In reset process, the driver will DOWN the port and then UINIT, in this case, the setup tc process will UP the port before UINIT, so cause the problem. Adds a DOWN process in UINIT to fix it.

In the Linux kernel, the following vulnerability has been resolved: net: wan: fsl_qmc_hdlc: Convert carrier_lock spinlock to a mutex The carrier_lock spinlock protects the carrier detection. While it is held, framer_get_status() is called which in turn takes a mutex. This is not correct and can lead to a deadlock. A run with PROVE_LOCKING enabled detected the issue: [ BUG: Invalid wait context ] ... c204ddbc (&framer->mutex){+.+.}-{3:3}, at: framer_get_status+0x40/0x78 other info that might help us debug this: context-{4:4} 2 locks held by ifconfig/146: #0: c0926a38 (rtnl_mutex){+.+.}-{3:3}, at: devinet_ioctl+0x12c/0x664 #1: c2006a40 (&qmc_hdlc->carrier_lock){....}-{2:2}, at: qmc_hdlc_framer_set_carrier+0x30/0x98 Avoid the spinlock usage and convert carrier_lock to a mutex.

In the Linux kernel, the following vulnerability has been resolved: drm/vmwgfx: Fix a deadlock in dma buf fence polling Introduce a version of the fence ops that on release doesn't remove the fence from the pending list, and thus doesn't require a lock to fix poll->fence wait->fence unref deadlocks. vmwgfx overwrites the wait callback to iterate over the list of all fences and update their status, to do that it holds a lock to prevent the list modifcations from other threads. The fence destroy callback both deletes the fence and removes it from the list of pending fences, for which it holds a lock. dma buf polling cb unrefs a fence after it's been signaled: so the poll calls the wait, which signals the fences, which are being destroyed. The destruction tries to acquire the lock on the pending fences list which it can never get because it's held by the wait from which it was called. Old bug, but not a lot of userspace apps were using dma-buf polling interfaces. Fix those, in particular this fixes KDE stalls/deadlock.

In the Linux kernel, the following vulnerability has been resolved: i3c: Use i3cdev->desc->info instead of calling i3c_device_get_info() to avoid deadlock A deadlock may happen since the i3c_master_register() acquires &i3cbus->lock twice. See the log below. Use i3cdev->desc->info instead of calling i3c_device_info() to avoid acquiring the lock twice. v2: - Modified the title and commit message ============================================ WARNING: possible recursive locking detected 6.11.0-mainline -------------------------------------------- init/1 is trying to acquire lock: f1ffff80a6a40dc0 (&i3cbus->lock){++++}-{3:3}, at: i3c_bus_normaluse_lock but task is already holding lock: f1ffff80a6a40dc0 (&i3cbus->lock){++++}-{3:3}, at: i3c_master_register other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&i3cbus->lock); lock(&i3cbus->lock); *** DEADLOCK *** May be due to missing lock nesting notation 2 locks held by init/1: #0: fcffff809b6798f8 (&dev->mutex){....}-{3:3}, at: __driver_attach #1: f1ffff80a6a40dc0 (&i3cbus->lock){++++}-{3:3}, at: i3c_master_register stack backtrace: CPU: 6 UID: 0 PID: 1 Comm: init Call trace: dump_backtrace+0xfc/0x17c show_stack+0x18/0x28 dump_stack_lvl+0x40/0xc0 dump_stack+0x18/0x24 print_deadlock_bug+0x388/0x390 __lock_acquire+0x18bc/0x32ec lock_acquire+0x134/0x2b0 down_read+0x50/0x19c i3c_bus_normaluse_lock+0x14/0x24 i3c_device_get_info+0x24/0x58 i3c_device_uevent+0x34/0xa4 dev_uevent+0x310/0x384 kobject_uevent_env+0x244/0x414 kobject_uevent+0x14/0x20 device_add+0x278/0x460 device_register+0x20/0x34 i3c_master_register_new_i3c_devs+0x78/0x154 i3c_master_register+0x6a0/0x6d4 mtk_i3c_master_probe+0x3b8/0x4d8 platform_probe+0xa0/0xe0 really_probe+0x114/0x454 __driver_probe_device+0xa0/0x15c driver_probe_device+0x3c/0x1ac __driver_attach+0xc4/0x1f0 bus_for_each_dev+0x104/0x160 driver_attach+0x24/0x34 bus_add_driver+0x14c/0x294 driver_register+0x68/0x104 __platform_driver_register+0x20/0x30 init_module+0x20/0xfe4 do_one_initcall+0x184/0x464 do_init_module+0x58/0x1ec load_module+0xefc/0x10c8 __arm64_sys_finit_module+0x238/0x33c invoke_syscall+0x58/0x10c el0_svc_common+0xa8/0xdc do_el0_svc+0x1c/0x28 el0_svc+0x50/0xac el0t_64_sync_handler+0x70/0xbc el0t_64_sync+0x1a8/0x1ac

In the Linux kernel, the following vulnerability has been resolved: memcg: fix soft lockup in the OOM process A soft lockup issue was found in the product with about 56,000 tasks were in the OOM cgroup, it was traversing them when the soft lockup was triggered. watchdog: BUG: soft lockup - CPU#2 stuck for 23s! [VM Thread:1503066] CPU: 2 PID: 1503066 Comm: VM Thread Kdump: loaded Tainted: G Hardware name: Huawei Cloud OpenStack Nova, BIOS RIP: 0010:console_unlock+0x343/0x540 RSP: 0000:ffffb751447db9a0 EFLAGS: 00000247 ORIG_RAX: ffffffffffffff13 RAX: 0000000000000001 RBX: 0000000000000000 RCX: 00000000ffffffff RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000247 RBP: ffffffffafc71f90 R08: 0000000000000000 R09: 0000000000000040 R10: 0000000000000080 R11: 0000000000000000 R12: ffffffffafc74bd0 R13: ffffffffaf60a220 R14: 0000000000000247 R15: 0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f2fe6ad91f0 CR3: 00000004b2076003 CR4: 0000000000360ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: vprintk_emit+0x193/0x280 printk+0x52/0x6e dump_task+0x114/0x130 mem_cgroup_scan_tasks+0x76/0x100 dump_header+0x1fe/0x210 oom_kill_process+0xd1/0x100 out_of_memory+0x125/0x570 mem_cgroup_out_of_memory+0xb5/0xd0 try_charge+0x720/0x770 mem_cgroup_try_charge+0x86/0x180 mem_cgroup_try_charge_delay+0x1c/0x40 do_anonymous_page+0xb5/0x390 handle_mm_fault+0xc4/0x1f0 This is because thousands of processes are in the OOM cgroup, it takes a long time to traverse all of them. As a result, this lead to soft lockup in the OOM process. To fix this issue, call 'cond_resched' in the 'mem_cgroup_scan_tasks' function per 1000 iterations. For global OOM, call 'touch_softlockup_watchdog' per 1000 iterations to avoid this issue.

In the Linux kernel, the following vulnerability has been resolved: Revert "media: v4l2-ctrls: show all owned controls in log_status" This reverts commit 9801b5b28c6929139d6fceeee8d739cc67bb2739. This patch introduced a potential deadlock scenario: [Wed May 8 10:02:06 2024] Possible unsafe locking scenario: [Wed May 8 10:02:06 2024] CPU0 CPU1 [Wed May 8 10:02:06 2024] ---- ---- [Wed May 8 10:02:06 2024] lock(vivid_ctrls:1620:(hdl_vid_cap)->_lock); [Wed May 8 10:02:06 2024] lock(vivid_ctrls:1608:(hdl_user_vid)->_lock); [Wed May 8 10:02:06 2024] lock(vivid_ctrls:1620:(hdl_vid_cap)->_lock); [Wed May 8 10:02:06 2024] lock(vivid_ctrls:1608:(hdl_user_vid)->_lock); For now just revert.

In the Linux kernel, the following vulnerability has been resolved: dma: xilinx_dpdma: Fix locking There are several places where either chan->lock or chan->vchan.lock was not held. Add appropriate locking. This fixes lockdep warnings like [ 31.077578] ------------[ cut here ]------------ [ 31.077831] WARNING: CPU: 2 PID: 40 at drivers/dma/xilinx/xilinx_dpdma.c:834 xilinx_dpdma_chan_queue_transfer+0x274/0x5e0 [ 31.077953] Modules linked in: [ 31.078019] CPU: 2 PID: 40 Comm: kworker/u12:1 Not tainted 6.6.20+ #98 [ 31.078102] Hardware name: xlnx,zynqmp (DT) [ 31.078169] Workqueue: events_unbound deferred_probe_work_func [ 31.078272] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 31.078377] pc : xilinx_dpdma_chan_queue_transfer+0x274/0x5e0 [ 31.078473] lr : xilinx_dpdma_chan_queue_transfer+0x270/0x5e0 [ 31.078550] sp : ffffffc083bb2e10 [ 31.078590] x29: ffffffc083bb2e10 x28: 0000000000000000 x27: ffffff880165a168 [ 31.078754] x26: ffffff880164e920 x25: ffffff880164eab8 x24: ffffff880164d480 [ 31.078920] x23: ffffff880165a148 x22: ffffff880164e988 x21: 0000000000000000 [ 31.079132] x20: ffffffc082aa3000 x19: ffffff880164e880 x18: 0000000000000000 [ 31.079295] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 [ 31.079453] x14: 0000000000000000 x13: ffffff8802263dc0 x12: 0000000000000001 [ 31.079613] x11: 0001ffc083bb2e34 x10: 0001ff880164e98f x9 : 0001ffc082aa3def [ 31.079824] x8 : 0001ffc082aa3dec x7 : 0000000000000000 x6 : 0000000000000516 [ 31.079982] x5 : ffffffc7f8d43000 x4 : ffffff88003c9c40 x3 : ffffffffffffffff [ 31.080147] x2 : ffffffc7f8d43000 x1 : 00000000000000c0 x0 : 0000000000000000 [ 31.080307] Call trace: [ 31.080340] xilinx_dpdma_chan_queue_transfer+0x274/0x5e0 [ 31.080518] xilinx_dpdma_issue_pending+0x11c/0x120 [ 31.080595] zynqmp_disp_layer_update+0x180/0x3ac [ 31.080712] zynqmp_dpsub_plane_atomic_update+0x11c/0x21c [ 31.080825] drm_atomic_helper_commit_planes+0x20c/0x684 [ 31.080951] drm_atomic_helper_commit_tail+0x5c/0xb0 [ 31.081139] commit_tail+0x234/0x294 [ 31.081246] drm_atomic_helper_commit+0x1f8/0x210 [ 31.081363] drm_atomic_commit+0x100/0x140 [ 31.081477] drm_client_modeset_commit_atomic+0x318/0x384 [ 31.081634] drm_client_modeset_commit_locked+0x8c/0x24c [ 31.081725] drm_client_modeset_commit+0x34/0x5c [ 31.081812] __drm_fb_helper_restore_fbdev_mode_unlocked+0x104/0x168 [ 31.081899] drm_fb_helper_set_par+0x50/0x70 [ 31.081971] fbcon_init+0x538/0xc48 [ 31.082047] visual_init+0x16c/0x23c [ 31.082207] do_bind_con_driver.isra.0+0x2d0/0x634 [ 31.082320] do_take_over_console+0x24c/0x33c [ 31.082429] do_fbcon_takeover+0xbc/0x1b0 [ 31.082503] fbcon_fb_registered+0x2d0/0x34c [ 31.082663] register_framebuffer+0x27c/0x38c [ 31.082767] __drm_fb_helper_initial_config_and_unlock+0x5c0/0x91c [ 31.082939] drm_fb_helper_initial_config+0x50/0x74 [ 31.083012] drm_fbdev_dma_client_hotplug+0xb8/0x108 [ 31.083115] drm_client_register+0xa0/0xf4 [ 31.083195] drm_fbdev_dma_setup+0xb0/0x1cc [ 31.083293] zynqmp_dpsub_drm_init+0x45c/0x4e0 [ 31.083431] zynqmp_dpsub_probe+0x444/0x5e0 [ 31.083616] platform_probe+0x8c/0x13c [ 31.083713] really_probe+0x258/0x59c [ 31.083793] __driver_probe_device+0xc4/0x224 [ 31.083878] driver_probe_device+0x70/0x1c0 [ 31.083961] __device_attach_driver+0x108/0x1e0 [ 31.084052] bus_for_each_drv+0x9c/0x100 [ 31.084125] __device_attach+0x100/0x298 [ 31.084207] device_initial_probe+0x14/0x20 [ 31.084292] bus_probe_device+0xd8/0xdc [ 31.084368] deferred_probe_work_func+0x11c/0x180 [ 31.084451] process_one_work+0x3ac/0x988 [ 31.084643] worker_thread+0x398/0x694 [ 31.084752] kthread+0x1bc/0x1c0 [ 31.084848] ret_from_fork+0x10/0x20 [ 31.084932] irq event stamp: 64549 [ 31.084970] hardirqs last enabled at (64548): [<ffffffc081adf35c>] _raw_spin_unlock_irqrestore+0x80/0x90 [ 31.085157] ---truncated---

In the Linux kernel, the following vulnerability has been resolved: bpf, sockmap: Prevent lock inversion deadlock in map delete elem syzkaller started using corpuses where a BPF tracing program deletes elements from a sockmap/sockhash map. Because BPF tracing programs can be invoked from any interrupt context, locks taken during a map_delete_elem operation must be hardirq-safe. Otherwise a deadlock due to lock inversion is possible, as reported by lockdep: CPU0 CPU1 ---- ---- lock(&htab->buckets[i].lock); local_irq_disable(); lock(&host->lock); lock(&htab->buckets[i].lock); <Interrupt> lock(&host->lock); Locks in sockmap are hardirq-unsafe by design. We expects elements to be deleted from sockmap/sockhash only in task (normal) context with interrupts enabled, or in softirq context. Detect when map_delete_elem operation is invoked from a context which is _not_ hardirq-unsafe, that is interrupts are disabled, and bail out with an error. Note that map updates are not affected by this issue. BPF verifier does not allow updating sockmap/sockhash from a BPF tracing program today.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid potential deadlock Using f2fs_trylock_op() in f2fs_write_compressed_pages() to avoid potential deadlock like we did in f2fs_write_single_data_page().

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: mark set as dead when unbinding anonymous set with timeout While the rhashtable set gc runs asynchronously, a race allows it to collect elements from anonymous sets with timeouts while it is being released from the commit path. Mingi Cho originally reported this issue in a different path in 6.1.x with a pipapo set with low timeouts which is not possible upstream since 7395dfacfff6 ("netfilter: nf_tables: use timestamp to check for set element timeout"). Fix this by setting on the dead flag for anonymous sets to skip async gc in this case. According to 08e4c8c5919f ("netfilter: nf_tables: mark newset as dead on transaction abort"), Florian plans to accelerate abort path by releasing objects via workqueue, therefore, this sets on the dead flag for abort path too.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fail bpf_timer_cancel when callback is being cancelled Given a schedule: timer1 cb timer2 cb bpf_timer_cancel(timer2); bpf_timer_cancel(timer1); Both bpf_timer_cancel calls would wait for the other callback to finish executing, introducing a lockup. Add an atomic_t count named 'cancelling' in bpf_hrtimer. This keeps track of all in-flight cancellation requests for a given BPF timer. Whenever cancelling a BPF timer, we must check if we have outstanding cancellation requests, and if so, we must fail the operation with an error (-EDEADLK) since cancellation is synchronous and waits for the callback to finish executing. This implies that we can enter a deadlock situation involving two or more timer callbacks executing in parallel and attempting to cancel one another. Note that we avoid incrementing the cancelling counter for the target timer (the one being cancelled) if bpf_timer_cancel is not invoked from a callback, to avoid spurious errors. The whole point of detecting cur->cancelling and returning -EDEADLK is to not enter a busy wait loop (which may or may not lead to a lockup). This does not apply in case the caller is in a non-callback context, the other side can continue to cancel as it sees fit without running into errors. Background on prior attempts: Earlier versions of this patch used a bool 'cancelling' bit and used the following pattern under timer->lock to publish cancellation status. lock(t->lock); t->cancelling = true; mb(); if (cur->cancelling) return -EDEADLK; unlock(t->lock); hrtimer_cancel(t->timer); t->cancelling = false; The store outside the critical section could overwrite a parallel requests t->cancelling assignment to true, to ensure the parallely executing callback observes its cancellation status. It would be necessary to clear this cancelling bit once hrtimer_cancel is done, but lack of serialization introduced races. Another option was explored where bpf_timer_start would clear the bit when (re)starting the timer under timer->lock. This would ensure serialized access to the cancelling bit, but may allow it to be cleared before in-flight hrtimer_cancel has finished executing, such that lockups can occur again. Thus, we choose an atomic counter to keep track of all outstanding cancellation requests and use it to prevent lockups in case callbacks attempt to cancel each other while executing in parallel.

In the Linux kernel, the following vulnerability has been resolved: md/raid5: fix deadlock that raid5d() wait for itself to clear MD_SB_CHANGE_PENDING Xiao reported that lvm2 test lvconvert-raid-takeover.sh can hang with small possibility, the root cause is exactly the same as commit bed9e27baf52 ("Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d"") However, Dan reported another hang after that, and junxiao investigated the problem and found out that this is caused by plugged bio can't issue from raid5d(). Current implementation in raid5d() has a weird dependence: 1) md_check_recovery() from raid5d() must hold 'reconfig_mutex' to clear MD_SB_CHANGE_PENDING; 2) raid5d() handles IO in a deadloop, until all IO are issued; 3) IO from raid5d() must wait for MD_SB_CHANGE_PENDING to be cleared; This behaviour is introduce before v2.6, and for consequence, if other context hold 'reconfig_mutex', and md_check_recovery() can't update super_block, then raid5d() will waste one cpu 100% by the deadloop, until 'reconfig_mutex' is released. Refer to the implementation from raid1 and raid10, fix this problem by skipping issue IO if MD_SB_CHANGE_PENDING is still set after md_check_recovery(), daemon thread will be woken up when 'reconfig_mutex' is released. Meanwhile, the hang problem will be fixed as well.

In the Linux kernel, the following vulnerability has been resolved: mm/hugetlb: fix hugetlb vs. core-mm PT locking We recently made GUP's common page table walking code to also walk hugetlb VMAs without most hugetlb special-casing, preparing for the future of having less hugetlb-specific page table walking code in the codebase. Turns out that we missed one page table locking detail: page table locking for hugetlb folios that are not mapped using a single PMD/PUD. Assume we have hugetlb folio that spans multiple PTEs (e.g., 64 KiB hugetlb folios on arm64 with 4 KiB base page size). GUP, as it walks the page tables, will perform a pte_offset_map_lock() to grab the PTE table lock. However, hugetlb that concurrently modifies these page tables would actually grab the mm->page_table_lock: with USE_SPLIT_PTE_PTLOCKS, the locks would differ. Something similar can happen right now with hugetlb folios that span multiple PMDs when USE_SPLIT_PMD_PTLOCKS. This issue can be reproduced [1], for example triggering: [ 3105.936100] ------------[ cut here ]------------ [ 3105.939323] WARNING: CPU: 31 PID: 2732 at mm/gup.c:142 try_grab_folio+0x11c/0x188 [ 3105.944634] Modules linked in: [...] [ 3105.974841] CPU: 31 PID: 2732 Comm: reproducer Not tainted 6.10.0-64.eln141.aarch64 #1 [ 3105.980406] Hardware name: QEMU KVM Virtual Machine, BIOS edk2-20240524-4.fc40 05/24/2024 [ 3105.986185] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 3105.991108] pc : try_grab_folio+0x11c/0x188 [ 3105.994013] lr : follow_page_pte+0xd8/0x430 [ 3105.996986] sp : ffff80008eafb8f0 [ 3105.999346] x29: ffff80008eafb900 x28: ffffffe8d481f380 x27: 00f80001207cff43 [ 3106.004414] x26: 0000000000000001 x25: 0000000000000000 x24: ffff80008eafba48 [ 3106.009520] x23: 0000ffff9372f000 x22: ffff7a54459e2000 x21: ffff7a546c1aa978 [ 3106.014529] x20: ffffffe8d481f3c0 x19: 0000000000610041 x18: 0000000000000001 [ 3106.019506] x17: 0000000000000001 x16: ffffffffffffffff x15: 0000000000000000 [ 3106.024494] x14: ffffb85477fdfe08 x13: 0000ffff9372ffff x12: 0000000000000000 [ 3106.029469] x11: 1fffef4a88a96be1 x10: ffff7a54454b5f0c x9 : ffffb854771b12f0 [ 3106.034324] x8 : 0008000000000000 x7 : ffff7a546c1aa980 x6 : 0008000000000080 [ 3106.038902] x5 : 00000000001207cf x4 : 0000ffff9372f000 x3 : ffffffe8d481f000 [ 3106.043420] x2 : 0000000000610041 x1 : 0000000000000001 x0 : 0000000000000000 [ 3106.047957] Call trace: [ 3106.049522] try_grab_folio+0x11c/0x188 [ 3106.051996] follow_pmd_mask.constprop.0.isra.0+0x150/0x2e0 [ 3106.055527] follow_page_mask+0x1a0/0x2b8 [ 3106.058118] __get_user_pages+0xf0/0x348 [ 3106.060647] faultin_page_range+0xb0/0x360 [ 3106.063651] do_madvise+0x340/0x598 Let's make huge_pte_lockptr() effectively use the same PT locks as any core-mm page table walker would. Add ptep_lockptr() to obtain the PTE page table lock using a pte pointer -- unfortunately we cannot convert pte_lockptr() because virt_to_page() doesn't work with kmap'ed page tables we can have with CONFIG_HIGHPTE. Handle CONFIG_PGTABLE_LEVELS correctly by checking in reverse order, such that when e.g., CONFIG_PGTABLE_LEVELS==2 with PGDIR_SIZE==P4D_SIZE==PUD_SIZE==PMD_SIZE will work as expected. Document why that works. There is one ugly case: powerpc 8xx, whereby we have an 8 MiB hugetlb folio being mapped using two PTE page tables. While hugetlb wants to take the PMD table lock, core-mm would grab the PTE table lock of one of both PTE page tables. In such corner cases, we have to make sure that both locks match, which is (fortunately!) currently guaranteed for 8xx as it does not support SMP and consequently doesn't use split PT locks. [1] https://lore.kernel.org/all/1bbfcc7f-f222-45a5-ac44-c5a1381c596d@redhat.com/

In the Linux kernel, the following vulnerability has been resolved: Revert "sched/fair: Make sure to try to detach at least one movable task" This reverts commit b0defa7ae03ecf91b8bfd10ede430cff12fcbd06. b0defa7ae03ec changed the load balancing logic to ignore env.max_loop if all tasks examined to that point were pinned. The goal of the patch was to make it more likely to be able to detach a task buried in a long list of pinned tasks. However, this has the unfortunate side effect of creating an O(n) iteration in detach_tasks(), as we now must fully iterate every task on a cpu if all or most are pinned. Since this load balance code is done with rq lock held, and often in softirq context, it is very easy to trigger hard lockups. We observed such hard lockups with a user who affined O(10k) threads to a single cpu. When I discussed this with Vincent he initially suggested that we keep the limit on the number of tasks to detach, but increase the number of tasks we can search. However, after some back and forth on the mailing list, he recommended we instead revert the original patch, as it seems likely no one was actually getting hit by the original issue.

In the Linux kernel, the following vulnerability has been resolved: scsi: hisi_sas: Fix a deadlock issue related to automatic dump If we issue a disabling PHY command, the device attached with it will go offline, if a 2 bit ECC error occurs at the same time, a hung task may be found: [ 4613.652388] INFO: task kworker/u256:0:165233 blocked for more than 120 seconds. [ 4613.666297] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 4613.674809] task:kworker/u256:0 state:D stack: 0 pid:165233 ppid: 2 flags:0x00000208 [ 4613.683959] Workqueue: 0000:74:02.0_disco_q sas_revalidate_domain [libsas] [ 4613.691518] Call trace: [ 4613.694678] __switch_to+0xf8/0x17c [ 4613.698872] __schedule+0x660/0xee0 [ 4613.703063] schedule+0xac/0x240 [ 4613.706994] schedule_timeout+0x500/0x610 [ 4613.711705] __down+0x128/0x36c [ 4613.715548] down+0x240/0x2d0 [ 4613.719221] hisi_sas_internal_abort_timeout+0x1bc/0x260 [hisi_sas_main] [ 4613.726618] sas_execute_internal_abort+0x144/0x310 [libsas] [ 4613.732976] sas_execute_internal_abort_dev+0x44/0x60 [libsas] [ 4613.739504] hisi_sas_internal_task_abort_dev.isra.0+0xbc/0x1b0 [hisi_sas_main] [ 4613.747499] hisi_sas_dev_gone+0x174/0x250 [hisi_sas_main] [ 4613.753682] sas_notify_lldd_dev_gone+0xec/0x2e0 [libsas] [ 4613.759781] sas_unregister_common_dev+0x4c/0x7a0 [libsas] [ 4613.765962] sas_destruct_devices+0xb8/0x120 [libsas] [ 4613.771709] sas_do_revalidate_domain.constprop.0+0x1b8/0x31c [libsas] [ 4613.778930] sas_revalidate_domain+0x60/0xa4 [libsas] [ 4613.784716] process_one_work+0x248/0x950 [ 4613.789424] worker_thread+0x318/0x934 [ 4613.793878] kthread+0x190/0x200 [ 4613.797810] ret_from_fork+0x10/0x18 [ 4613.802121] INFO: task kworker/u256:4:316722 blocked for more than 120 seconds. [ 4613.816026] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 4613.824538] task:kworker/u256:4 state:D stack: 0 pid:316722 ppid: 2 flags:0x00000208 [ 4613.833670] Workqueue: 0000:74:02.0 hisi_sas_rst_work_handler [hisi_sas_main] [ 4613.841491] Call trace: [ 4613.844647] __switch_to+0xf8/0x17c [ 4613.848852] __schedule+0x660/0xee0 [ 4613.853052] schedule+0xac/0x240 [ 4613.856984] schedule_timeout+0x500/0x610 [ 4613.861695] __down+0x128/0x36c [ 4613.865542] down+0x240/0x2d0 [ 4613.869216] hisi_sas_controller_prereset+0x58/0x1fc [hisi_sas_main] [ 4613.876324] hisi_sas_rst_work_handler+0x40/0x8c [hisi_sas_main] [ 4613.883019] process_one_work+0x248/0x950 [ 4613.887732] worker_thread+0x318/0x934 [ 4613.892204] kthread+0x190/0x200 [ 4613.896118] ret_from_fork+0x10/0x18 [ 4613.900423] INFO: task kworker/u256:1:348985 blocked for more than 121 seconds. [ 4613.914341] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 4613.922852] task:kworker/u256:1 state:D stack: 0 pid:348985 ppid: 2 flags:0x00000208 [ 4613.931984] Workqueue: 0000:74:02.0_event_q sas_port_event_worker [libsas] [ 4613.939549] Call trace: [ 4613.942702] __switch_to+0xf8/0x17c [ 4613.946892] __schedule+0x660/0xee0 [ 4613.951083] schedule+0xac/0x240 [ 4613.955015] schedule_timeout+0x500/0x610 [ 4613.959725] wait_for_common+0x200/0x610 [ 4613.964349] wait_for_completion+0x3c/0x5c [ 4613.969146] flush_workqueue+0x198/0x790 [ 4613.973776] sas_porte_broadcast_rcvd+0x1e8/0x320 [libsas] [ 4613.979960] sas_port_event_worker+0x54/0xa0 [libsas] [ 4613.985708] process_one_work+0x248/0x950 [ 4613.990420] worker_thread+0x318/0x934 [ 4613.994868] kthread+0x190/0x200 [ 4613.998800] ret_from_fork+0x10/0x18 This is because when the device goes offline, we obtain the hisi_hba semaphore and send the ABORT_DEV command to the device. However, the internal abort timed out due to the 2 bit ECC error and triggers automatic dump. In addition, since the hisi_hba semaphore has been obtained, the dump cannot be executed and the controller cannot be reset. Therefore, the deadlocks occur on the following circular dependencies ---truncated---

In the Linux kernel, the following vulnerability has been resolved: media: mediatek: vcodec: prevent kernel crash when rmmod mtk-vcodec-dec.ko If the driver support subdev mode, the parameter "dev->pm.dev" will be NULL in mtk_vcodec_dec_remove. Kernel will crash when try to rmmod mtk-vcodec-dec.ko. [ 4380.702726] pc : do_raw_spin_trylock+0x4/0x80 [ 4380.707075] lr : _raw_spin_lock_irq+0x90/0x14c [ 4380.711509] sp : ffff80000819bc10 [ 4380.714811] x29: ffff80000819bc10 x28: ffff3600c03e4000 x27: 0000000000000000 [ 4380.721934] x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000000 [ 4380.729057] x23: ffff3600c0f34930 x22: ffffd5e923549000 x21: 0000000000000220 [ 4380.736179] x20: 0000000000000208 x19: ffffd5e9213e8ebc x18: 0000000000000020 [ 4380.743298] x17: 0000002000000000 x16: ffffd5e9213e8e90 x15: 696c346f65646976 [ 4380.750420] x14: 0000000000000000 x13: 0000000000000001 x12: 0000000000000040 [ 4380.757542] x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000 [ 4380.764664] x8 : 0000000000000000 x7 : ffff3600c7273ae8 x6 : ffffd5e9213e8ebc [ 4380.771786] x5 : 0000000000000000 x4 : 0000000000000001 x3 : 0000000000000000 [ 4380.778908] x2 : 0000000000000000 x1 : ffff3600c03e4000 x0 : 0000000000000208 [ 4380.786031] Call trace: [ 4380.788465] do_raw_spin_trylock+0x4/0x80 [ 4380.792462] __pm_runtime_disable+0x2c/0x1b0 [ 4380.796723] mtk_vcodec_dec_remove+0x5c/0xa0 [mtk_vcodec_dec] [ 4380.802466] platform_remove+0x2c/0x60 [ 4380.806204] __device_release_driver+0x194/0x250 [ 4380.810810] driver_detach+0xc8/0x15c [ 4380.814462] bus_remove_driver+0x5c/0xb0 [ 4380.818375] driver_unregister+0x34/0x64 [ 4380.822288] platform_driver_unregister+0x18/0x24 [ 4380.826979] mtk_vcodec_dec_driver_exit+0x1c/0x888 [mtk_vcodec_dec] [ 4380.833240] __arm64_sys_delete_module+0x190/0x224 [ 4380.838020] invoke_syscall+0x48/0x114 [ 4380.841760] el0_svc_common.constprop.0+0x60/0x11c [ 4380.846540] do_el0_svc+0x28/0x90 [ 4380.849844] el0_svc+0x4c/0x100 [ 4380.852975] el0t_64_sync_handler+0xec/0xf0 [ 4380.857148] el0t_64_sync+0x190/0x194 [ 4380.860801] Code: 94431515 17ffffca d503201f d503245f (b9400004)

In the Linux kernel, the following vulnerability has been resolved: ceph: fix possible deadlock when holding Fwb to get inline_data 1, mount with wsync. 2, create a file with O_RDWR, and the request was sent to mds.0: ceph_atomic_open()--> ceph_mdsc_do_request(openc) finish_open(file, dentry, ceph_open)--> ceph_open()--> ceph_init_file()--> ceph_init_file_info()--> ceph_uninline_data()--> { ... if (inline_version == 1 || /* initial version, no data */ inline_version == CEPH_INLINE_NONE) goto out_unlock; ... } The inline_version will be 1, which is the initial version for the new create file. And here the ci->i_inline_version will keep with 1, it's buggy. 3, buffer write to the file immediately: ceph_write_iter()--> ceph_get_caps(file, need=Fw, want=Fb, ...); generic_perform_write()--> a_ops->write_begin()--> ceph_write_begin()--> netfs_write_begin()--> netfs_begin_read()--> netfs_rreq_submit_slice()--> netfs_read_from_server()--> rreq->netfs_ops->issue_read()--> ceph_netfs_issue_read()--> { ... if (ci->i_inline_version != CEPH_INLINE_NONE && ceph_netfs_issue_op_inline(subreq)) return; ... } ceph_put_cap_refs(ci, Fwb); The ceph_netfs_issue_op_inline() will send a getattr(Fsr) request to mds.1. 4, then the mds.1 will request the rd lock for CInode::filelock from the auth mds.0, the mds.0 will do the CInode::filelock state transation from excl --> sync, but it need to revoke the Fxwb caps back from the clients. While the kernel client has aleady held the Fwb caps and waiting for the getattr(Fsr). It's deadlock! URL: https://tracker.ceph.com/issues/55377

In the Linux kernel, the following vulnerability has been resolved: mptcp: fix sleep in atomic at close time Matt reported a splat at msk close time: BUG: sleeping function called from invalid context at net/mptcp/protocol.c:2877 in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 155, name: packetdrill preempt_count: 201, expected: 0 RCU nest depth: 0, expected: 0 4 locks held by packetdrill/155: #0: ffff888001536990 (&sb->s_type->i_mutex_key#6){+.+.}-{3:3}, at: __sock_release (net/socket.c:650) #1: ffff88800b498130 (sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_close (net/mptcp/protocol.c:2973) #2: ffff88800b49a130 (sk_lock-AF_INET/1){+.+.}-{0:0}, at: __mptcp_close_ssk (net/mptcp/protocol.c:2363) #3: ffff88800b49a0b0 (slock-AF_INET){+...}-{2:2}, at: __lock_sock_fast (include/net/sock.h:1820) Preemption disabled at: 0x0 CPU: 1 PID: 155 Comm: packetdrill Not tainted 6.1.0-rc5 #365 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:107 (discriminator 4)) __might_resched.cold (kernel/sched/core.c:9891) __mptcp_destroy_sock (include/linux/kernel.h:110) __mptcp_close (net/mptcp/protocol.c:2959) mptcp_subflow_queue_clean (include/net/sock.h:1777) __mptcp_close_ssk (net/mptcp/protocol.c:2363) mptcp_destroy_common (net/mptcp/protocol.c:3170) mptcp_destroy (include/net/sock.h:1495) __mptcp_destroy_sock (net/mptcp/protocol.c:2886) __mptcp_close (net/mptcp/protocol.c:2959) mptcp_close (net/mptcp/protocol.c:2974) inet_release (net/ipv4/af_inet.c:432) __sock_release (net/socket.c:651) sock_close (net/socket.c:1367) __fput (fs/file_table.c:320) task_work_run (kernel/task_work.c:181 (discriminator 1)) exit_to_user_mode_prepare (include/linux/resume_user_mode.h:49) syscall_exit_to_user_mode (kernel/entry/common.c:130) do_syscall_64 (arch/x86/entry/common.c:87) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) We can't call mptcp_close under the 'fast' socket lock variant, replace it with a sock_lock_nested() as the relevant code is already under the listening msk socket lock protection.

NVIDIA GPU Display Driver for Windows and Linux contains a vulnerability in the kernel mode layer, where an unprivileged user can cause a null-pointer dereference, which may lead to denial of service.

A memory leak in the ql_alloc_large_buffers() function in drivers/net/ethernet/qlogic/qla3xxx.c in the Linux kernel before 5.3.5 allows local users to cause a denial of service (memory consumption) by triggering pci_dma_mapping_error() failures, aka CID-1acb8f2a7a9f.

A vulnerability, which was classified as problematic, has been found in Linux Kernel. This issue affects the function unix_sock_destructor/unix_release_sock of the file net/unix/af_unix.c of the component BPF. The manipulation leads to memory leak. It is recommended to apply a patch to fix this issue. The associated identifier of this vulnerability is VDB-211043.

kernel/trace/ftrace.c in the Linux kernel before 2.6.35.5, when debugfs is enabled, does not properly handle interaction between mutex possession and llseek operations, which allows local users to cause a denial of service (NULL pointer dereference and outage of all function tracing files) via an lseek call on a file descriptor associated with the set_ftrace_filter file.

In the Linux kernel, the following vulnerability has been resolved: skmsg: Skip zero length skb in sk_msg_recvmsg When running BPF selftests (./test_progs -t sockmap_basic) on a Loongarch platform, the following kernel panic occurs: [...] Oops[#1]: CPU: 22 PID: 2824 Comm: test_progs Tainted: G OE 6.10.0-rc2+ #18 Hardware name: LOONGSON Dabieshan/Loongson-TC542F0, BIOS Loongson-UDK2018 ... ... ra: 90000000048bf6c0 sk_msg_recvmsg+0x120/0x560 ERA: 9000000004162774 copy_page_to_iter+0x74/0x1c0 CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE) PRMD: 0000000c (PPLV0 +PIE +PWE) EUEN: 00000007 (+FPE +SXE +ASXE -BTE) ECFG: 00071c1d (LIE=0,2-4,10-12 VS=7) ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0) BADV: 0000000000000040 PRID: 0014c011 (Loongson-64bit, Loongson-3C5000) Modules linked in: bpf_testmod(OE) xt_CHECKSUM xt_MASQUERADE xt_conntrack Process test_progs (pid: 2824, threadinfo=0000000000863a31, task=...) Stack : ... Call Trace: [<9000000004162774>] copy_page_to_iter+0x74/0x1c0 [<90000000048bf6c0>] sk_msg_recvmsg+0x120/0x560 [<90000000049f2b90>] tcp_bpf_recvmsg_parser+0x170/0x4e0 [<90000000049aae34>] inet_recvmsg+0x54/0x100 [<900000000481ad5c>] sock_recvmsg+0x7c/0xe0 [<900000000481e1a8>] __sys_recvfrom+0x108/0x1c0 [<900000000481e27c>] sys_recvfrom+0x1c/0x40 [<9000000004c076ec>] do_syscall+0x8c/0xc0 [<9000000003731da4>] handle_syscall+0xc4/0x160 Code: ... ---[ end trace 0000000000000000 ]--- Kernel panic - not syncing: Fatal exception Kernel relocated by 0x3510000 .text @ 0x9000000003710000 .data @ 0x9000000004d70000 .bss @ 0x9000000006469400 ---[ end Kernel panic - not syncing: Fatal exception ]--- [...] This crash happens every time when running sockmap_skb_verdict_shutdown subtest in sockmap_basic. This crash is because a NULL pointer is passed to page_address() in the sk_msg_recvmsg(). Due to the different implementations depending on the architecture, page_address(NULL) will trigger a panic on Loongarch platform but not on x86 platform. So this bug was hidden on x86 platform for a while, but now it is exposed on Loongarch platform. The root cause is that a zero length skb (skb->len == 0) was put on the queue. This zero length skb is a TCP FIN packet, which was sent by shutdown(), invoked in test_sockmap_skb_verdict_shutdown(): shutdown(p1, SHUT_WR); In this case, in sk_psock_skb_ingress_enqueue(), num_sge is zero, and no page is put to this sge (see sg_set_page in sg_set_page), but this empty sge is queued into ingress_msg list. And in sk_msg_recvmsg(), this empty sge is used, and a NULL page is got by sg_page(sge). Pass this NULL page to copy_page_to_iter(), which passes it to kmap_local_page() and to page_address(), then kernel panics. To solve this, we should skip this zero length skb. So in sk_msg_recvmsg(), if copy is zero, that means it's a zero length skb, skip invoking copy_page_to_iter(). We are using the EFAULT return triggered by copy_page_to_iter to check for is_fin in tcp_bpf.c.

In the Linux kernel, the following vulnerability has been resolved: f2fs: check discard support for conventional zones As the helper function f2fs_bdev_support_discard() shows, f2fs checks if the target block devices support discard by calling bdev_max_discard_sectors() and bdev_is_zoned(). This check works well for most cases, but it does not work for conventional zones on zoned block devices. F2fs assumes that zoned block devices support discard, and calls __submit_discard_cmd(). When __submit_discard_cmd() is called for sequential write required zones, it works fine since __submit_discard_cmd() issues zone reset commands instead of discard commands. However, when __submit_discard_cmd() is called for conventional zones, __blkdev_issue_discard() is called even when the devices do not support discard. The inappropriate __blkdev_issue_discard() call was not a problem before the commit 30f1e7241422 ("block: move discard checks into the ioctl handler") because __blkdev_issue_discard() checked if the target devices support discard or not. If not, it returned EOPNOTSUPP. After the commit, __blkdev_issue_discard() no longer checks it. It always returns zero and sets NULL to the given bio pointer. This NULL pointer triggers f2fs_bug_on() in __submit_discard_cmd(). The BUG is recreated with the commands below at the umount step, where /dev/nullb0 is a zoned null_blk with 5GB total size, 128MB zone size and 10 conventional zones. $ mkfs.f2fs -f -m /dev/nullb0 $ mount /dev/nullb0 /mnt $ for ((i=0;i<5;i++)); do dd if=/dev/zero of=/mnt/test bs=65536 count=1600 conv=fsync; done $ umount /mnt To fix the BUG, avoid the inappropriate __blkdev_issue_discard() call. When discard is requested for conventional zones, check if the device supports discard or not. If not, return EOPNOTSUPP.

A vulnerability was reported in the Open vSwitch sub-component in the Linux Kernel. The flaw occurs when a recursive operation of code push recursively calls into the code block. The OVS module does not validate the stack depth, pushing too many frames and causing a stack overflow. As a result, this can lead to a crash or other related issues.

A NULL pointer dereference flaw was found in dbFree in fs/jfs/jfs_dmap.c in the journaling file system (JFS) in the Linux Kernel. This issue may allow a local attacker to crash the system due to a missing sanity check.

A vulnerability was found in Linux Kernel. It has been classified as problematic. This affects the function find_prog_by_sec_insn of the file tools/lib/bpf/libbpf.c of the component BPF. The manipulation leads to null pointer dereference. It is recommended to apply a patch to fix this issue. The identifier VDB-211749 was assigned to this vulnerability.

In the Linux kernel, the following vulnerability has been resolved: ocfs2: fix NULL pointer dereference in ocfs2_journal_dirty() bdev->bd_super has been removed and commit 8887b94d9322 change the usage from bdev->bd_super to b_assoc_map->host->i_sb. This introduces the following NULL pointer dereference in ocfs2_journal_dirty() since b_assoc_map is still not initialized. This can be easily reproduced by running xfstests generic/186, which simulate no more credits. [ 134.351592] BUG: kernel NULL pointer dereference, address: 0000000000000000 ... [ 134.355341] RIP: 0010:ocfs2_journal_dirty+0x14f/0x160 [ocfs2] ... [ 134.365071] Call Trace: [ 134.365312] <TASK> [ 134.365524] ? __die_body+0x1e/0x60 [ 134.365868] ? page_fault_oops+0x13d/0x4f0 [ 134.366265] ? __pfx_bit_wait_io+0x10/0x10 [ 134.366659] ? schedule+0x27/0xb0 [ 134.366981] ? exc_page_fault+0x6a/0x140 [ 134.367356] ? asm_exc_page_fault+0x26/0x30 [ 134.367762] ? ocfs2_journal_dirty+0x14f/0x160 [ocfs2] [ 134.368305] ? ocfs2_journal_dirty+0x13d/0x160 [ocfs2] [ 134.368837] ocfs2_create_new_meta_bhs.isra.51+0x139/0x2e0 [ocfs2] [ 134.369454] ocfs2_grow_tree+0x688/0x8a0 [ocfs2] [ 134.369927] ocfs2_split_and_insert.isra.67+0x35c/0x4a0 [ocfs2] [ 134.370521] ocfs2_split_extent+0x314/0x4d0 [ocfs2] [ 134.371019] ocfs2_change_extent_flag+0x174/0x410 [ocfs2] [ 134.371566] ocfs2_add_refcount_flag+0x3fa/0x630 [ocfs2] [ 134.372117] ocfs2_reflink_remap_extent+0x21b/0x4c0 [ocfs2] [ 134.372994] ? inode_update_timestamps+0x4a/0x120 [ 134.373692] ? __pfx_ocfs2_journal_access_di+0x10/0x10 [ocfs2] [ 134.374545] ? __pfx_ocfs2_journal_access_di+0x10/0x10 [ocfs2] [ 134.375393] ocfs2_reflink_remap_blocks+0xe4/0x4e0 [ocfs2] [ 134.376197] ocfs2_remap_file_range+0x1de/0x390 [ocfs2] [ 134.376971] ? security_file_permission+0x29/0x50 [ 134.377644] vfs_clone_file_range+0xfe/0x320 [ 134.378268] ioctl_file_clone+0x45/0xa0 [ 134.378853] do_vfs_ioctl+0x457/0x990 [ 134.379422] __x64_sys_ioctl+0x6e/0xd0 [ 134.379987] do_syscall_64+0x5d/0x170 [ 134.380550] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 134.381231] RIP: 0033:0x7fa4926397cb [ 134.381786] Code: 73 01 c3 48 8b 0d bd 56 38 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 8d 56 38 00 f7 d8 64 89 01 48 [ 134.383930] RSP: 002b:00007ffc2b39f7b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 134.384854] RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00007fa4926397cb [ 134.385734] RDX: 00007ffc2b39f7f0 RSI: 000000004020940d RDI: 0000000000000003 [ 134.386606] RBP: 0000000000000000 R08: 00111a82a4f015bb R09: 00007fa494221000 [ 134.387476] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 [ 134.388342] R13: 0000000000f10000 R14: 0000558e844e2ac8 R15: 0000000000f10000 [ 134.389207] </TASK> Fix it by only aborting transaction and journal in ocfs2_journal_dirty() now, and leave ocfs2_abort() later when detecting an aborted handle, e.g. start next transaction. Also log the handle details in this case.

NVIDIA GPU Display Driver for Windows and Linux contains a vulnerability in the kernel mode layer, where a local user with basic capabilities can cause a null-pointer dereference, which may lead to denial of service.

NVIDIA GPU Display Driver for Linux contains a vulnerability in the kernel mode layer handler, where an integer truncation can lead to an out-of-bounds read, which may lead to denial of service.

net/unix/af_unix.c in the Linux kernel 2.6.31.4 and earlier allows local users to cause a denial of service (system hang) by creating an abstract-namespace AF_UNIX listening socket, performing a shutdown operation on this socket, and then performing a series of connect operations to this socket.

The WRMSR processing functionality in the KVM subsystem in the Linux kernel through 3.17.2 does not properly handle the writing of a non-canonical address to a model-specific register, which allows guest OS users to cause a denial of service (host OS crash) by leveraging guest OS privileges, related to the wrmsr_interception function in arch/x86/kvm/svm.c and the handle_wrmsr function in arch/x86/kvm/vmx.c.

arch/x86/kvm/vmx.c in the KVM subsystem in the Linux kernel before 3.17.2 on Intel processors does not ensure that the value in the CR4 control register remains the same after a VM entry, which allows host OS users to kill arbitrary processes or cause a denial of service (system disruption) by leveraging /dev/kvm access, as demonstrated by PR_SET_TSC prctl calls within a modified copy of QEMU.

NVIDIA GPU Display Driver for Linux contains a vulnerability in the kernel mode layer, where an unprivileged regular user can cause a null-pointer dereference, which may lead to denial of service.

A flaw was found in the blkgs destruction path in block/blk-cgroup.c in the Linux kernel, leading to a cgroup blkio memory leakage problem. When a cgroup is being destroyed, cgroup_rstat_flush() is only called at css_release_work_fn(), which is called when the blkcg reference count reaches 0. This circular dependency will prevent blkcg and some blkgs from being freed after they are made offline. This issue may allow an attacker with a local access to cause system instability, such as an out of memory error.

A memory leak problem was found in ctnetlink_create_conntrack in net/netfilter/nf_conntrack_netlink.c in the Linux Kernel. This issue may allow a local attacker with CAP_NET_ADMIN privileges to cause a denial of service (DoS) attack due to a refcount overflow.

A null pointer dereference vulnerability was found in dpll_pin_parent_pin_set() in drivers/dpll/dpll_netlink.c in the Digital Phase Locked Loop (DPLL) subsystem in the Linux kernel. This issue could be exploited to trigger a denial of service.