In the Linux kernel, the following vulnerability has been resolved: PCI/MSI: Fix UAF in msi_capability_init KFENCE reports the following UAF: BUG: KFENCE: use-after-free read in __pci_enable_msi_range+0x2c0/0x488 Use-after-free read at 0x0000000024629571 (in kfence-#12): __pci_enable_msi_range+0x2c0/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 kfence-#12: 0x0000000008614900-0x00000000e06c228d, size=104, cache=kmalloc-128 allocated by task 81 on cpu 7 at 10.808142s: __kmem_cache_alloc_node+0x1f0/0x2bc kmalloc_trace+0x44/0x138 msi_alloc_desc+0x3c/0x9c msi_domain_insert_msi_desc+0x30/0x78 msi_setup_msi_desc+0x13c/0x184 __pci_enable_msi_range+0x258/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 freed by task 81 on cpu 7 at 10.811436s: msi_domain_free_descs+0xd4/0x10c msi_domain_free_locked.part.0+0xc0/0x1d8 msi_domain_alloc_irqs_all_locked+0xb4/0xbc pci_msi_setup_msi_irqs+0x30/0x4c __pci_enable_msi_range+0x2a8/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 Descriptor allocation done in: __pci_enable_msi_range msi_capability_init msi_setup_msi_desc msi_insert_msi_desc msi_domain_insert_msi_desc msi_alloc_desc ... Freed in case of failure in __msi_domain_alloc_locked() __pci_enable_msi_range msi_capability_init pci_msi_setup_msi_irqs msi_domain_alloc_irqs_all_locked msi_domain_alloc_locked __msi_domain_alloc_locked => fails msi_domain_free_locked ... That failure propagates back to pci_msi_setup_msi_irqs() in msi_capability_init() which accesses the descriptor for unmasking in the error exit path. Cure it by copying the descriptor and using the copy for the error exit path unmask operation. [ tglx: Massaged change log ]

In the Linux kernel, the following vulnerability has been resolved: fbmem: Do not delete the mode that is still in use The execution of fb_delete_videomode() is not based on the result of the previous fbcon_mode_deleted(). As a result, the mode is directly deleted, regardless of whether it is still in use, which may cause UAF. ================================================================== BUG: KASAN: use-after-free in fb_mode_is_equal+0x36e/0x5e0 \ drivers/video/fbdev/core/modedb.c:924 Read of size 4 at addr ffff88807e0ddb1c by task syz-executor.0/18962 CPU: 2 PID: 18962 Comm: syz-executor.0 Not tainted 5.10.45-rc1+ #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ... Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x137/0x1be lib/dump_stack.c:118 print_address_description+0x6c/0x640 mm/kasan/report.c:385 __kasan_report mm/kasan/report.c:545 [inline] kasan_report+0x13d/0x1e0 mm/kasan/report.c:562 fb_mode_is_equal+0x36e/0x5e0 drivers/video/fbdev/core/modedb.c:924 fbcon_mode_deleted+0x16a/0x220 drivers/video/fbdev/core/fbcon.c:2746 fb_set_var+0x1e1/0xdb0 drivers/video/fbdev/core/fbmem.c:975 do_fb_ioctl+0x4d9/0x6e0 drivers/video/fbdev/core/fbmem.c:1108 vfs_ioctl fs/ioctl.c:48 [inline] __do_sys_ioctl fs/ioctl.c:753 [inline] __se_sys_ioctl+0xfb/0x170 fs/ioctl.c:739 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Freed by task 18960: kasan_save_stack mm/kasan/common.c:48 [inline] kasan_set_track+0x3d/0x70 mm/kasan/common.c:56 kasan_set_free_info+0x17/0x30 mm/kasan/generic.c:355 __kasan_slab_free+0x108/0x140 mm/kasan/common.c:422 slab_free_hook mm/slub.c:1541 [inline] slab_free_freelist_hook+0xd6/0x1a0 mm/slub.c:1574 slab_free mm/slub.c:3139 [inline] kfree+0xca/0x3d0 mm/slub.c:4121 fb_delete_videomode+0x56a/0x820 drivers/video/fbdev/core/modedb.c:1104 fb_set_var+0x1f3/0xdb0 drivers/video/fbdev/core/fbmem.c:978 do_fb_ioctl+0x4d9/0x6e0 drivers/video/fbdev/core/fbmem.c:1108 vfs_ioctl fs/ioctl.c:48 [inline] __do_sys_ioctl fs/ioctl.c:753 [inline] __se_sys_ioctl+0xfb/0x170 fs/ioctl.c:739 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46 entry_SYSCALL_64_after_hwframe+0x44/0xa9

In the Linux kernel, the following vulnerability has been resolved: spi: Fix use-after-free with devm_spi_alloc_* We can't rely on the contents of the devres list during spi_unregister_controller(), as the list is already torn down at the time we perform devres_find() for devm_spi_release_controller. This causes devices registered with devm_spi_alloc_{master,slave}() to be mistakenly identified as legacy, non-devm managed devices and have their reference counters decremented below 0. ------------[ cut here ]------------ WARNING: CPU: 1 PID: 660 at lib/refcount.c:28 refcount_warn_saturate+0x108/0x174 [<b0396f04>] (refcount_warn_saturate) from [<b03c56a4>] (kobject_put+0x90/0x98) [<b03c5614>] (kobject_put) from [<b0447b4c>] (put_device+0x20/0x24) r4:b6700140 [<b0447b2c>] (put_device) from [<b07515e8>] (devm_spi_release_controller+0x3c/0x40) [<b07515ac>] (devm_spi_release_controller) from [<b045343c>] (release_nodes+0x84/0xc4) r5:b6700180 r4:b6700100 [<b04533b8>] (release_nodes) from [<b0454160>] (devres_release_all+0x5c/0x60) r8:b1638c54 r7:b117ad94 r6:b1638c10 r5:b117ad94 r4:b163dc10 [<b0454104>] (devres_release_all) from [<b044e41c>] (__device_release_driver+0x144/0x1ec) r5:b117ad94 r4:b163dc10 [<b044e2d8>] (__device_release_driver) from [<b044f70c>] (device_driver_detach+0x84/0xa0) r9:00000000 r8:00000000 r7:b117ad94 r6:b163dc54 r5:b1638c10 r4:b163dc10 [<b044f688>] (device_driver_detach) from [<b044d274>] (unbind_store+0xe4/0xf8) Instead, determine the devm allocation state as a flag on the controller which is guaranteed to be stable during cleanup.

In the Linux kernel, the following vulnerability has been resolved: pid: take a reference when initializing `cad_pid` During boot, kernel_init_freeable() initializes `cad_pid` to the init task's struct pid. Later on, we may change `cad_pid` via a sysctl, and when this happens proc_do_cad_pid() will increment the refcount on the new pid via get_pid(), and will decrement the refcount on the old pid via put_pid(). As we never called get_pid() when we initialized `cad_pid`, we decrement a reference we never incremented, can therefore free the init task's struct pid early. As there can be dangling references to the struct pid, we can later encounter a use-after-free (e.g. when delivering signals). This was spotted when fuzzing v5.13-rc3 with Syzkaller, but seems to have been around since the conversion of `cad_pid` to struct pid in commit 9ec52099e4b8 ("[PATCH] replace cad_pid by a struct pid") from the pre-KASAN stone age of v2.6.19. Fix this by getting a reference to the init task's struct pid when we assign it to `cad_pid`. Full KASAN splat below. ================================================================== BUG: KASAN: use-after-free in ns_of_pid include/linux/pid.h:153 [inline] BUG: KASAN: use-after-free in task_active_pid_ns+0xc0/0xc8 kernel/pid.c:509 Read of size 4 at addr ffff23794dda0004 by task syz-executor.0/273 CPU: 1 PID: 273 Comm: syz-executor.0 Not tainted 5.12.0-00001-g9aef892b2d15 #1 Hardware name: linux,dummy-virt (DT) Call trace: ns_of_pid include/linux/pid.h:153 [inline] task_active_pid_ns+0xc0/0xc8 kernel/pid.c:509 do_notify_parent+0x308/0xe60 kernel/signal.c:1950 exit_notify kernel/exit.c:682 [inline] do_exit+0x2334/0x2bd0 kernel/exit.c:845 do_group_exit+0x108/0x2c8 kernel/exit.c:922 get_signal+0x4e4/0x2a88 kernel/signal.c:2781 do_signal arch/arm64/kernel/signal.c:882 [inline] do_notify_resume+0x300/0x970 arch/arm64/kernel/signal.c:936 work_pending+0xc/0x2dc Allocated by task 0: slab_post_alloc_hook+0x50/0x5c0 mm/slab.h:516 slab_alloc_node mm/slub.c:2907 [inline] slab_alloc mm/slub.c:2915 [inline] kmem_cache_alloc+0x1f4/0x4c0 mm/slub.c:2920 alloc_pid+0xdc/0xc00 kernel/pid.c:180 copy_process+0x2794/0x5e18 kernel/fork.c:2129 kernel_clone+0x194/0x13c8 kernel/fork.c:2500 kernel_thread+0xd4/0x110 kernel/fork.c:2552 rest_init+0x44/0x4a0 init/main.c:687 arch_call_rest_init+0x1c/0x28 start_kernel+0x520/0x554 init/main.c:1064 0x0 Freed by task 270: slab_free_hook mm/slub.c:1562 [inline] slab_free_freelist_hook+0x98/0x260 mm/slub.c:1600 slab_free mm/slub.c:3161 [inline] kmem_cache_free+0x224/0x8e0 mm/slub.c:3177 put_pid.part.4+0xe0/0x1a8 kernel/pid.c:114 put_pid+0x30/0x48 kernel/pid.c:109 proc_do_cad_pid+0x190/0x1b0 kernel/sysctl.c:1401 proc_sys_call_handler+0x338/0x4b0 fs/proc/proc_sysctl.c:591 proc_sys_write+0x34/0x48 fs/proc/proc_sysctl.c:617 call_write_iter include/linux/fs.h:1977 [inline] new_sync_write+0x3ac/0x510 fs/read_write.c:518 vfs_write fs/read_write.c:605 [inline] vfs_write+0x9c4/0x1018 fs/read_write.c:585 ksys_write+0x124/0x240 fs/read_write.c:658 __do_sys_write fs/read_write.c:670 [inline] __se_sys_write fs/read_write.c:667 [inline] __arm64_sys_write+0x78/0xb0 fs/read_write.c:667 __invoke_syscall arch/arm64/kernel/syscall.c:37 [inline] invoke_syscall arch/arm64/kernel/syscall.c:49 [inline] el0_svc_common.constprop.1+0x16c/0x388 arch/arm64/kernel/syscall.c:129 do_el0_svc+0xf8/0x150 arch/arm64/kernel/syscall.c:168 el0_svc+0x28/0x38 arch/arm64/kernel/entry-common.c:416 el0_sync_handler+0x134/0x180 arch/arm64/kernel/entry-common.c:432 el0_sync+0x154/0x180 arch/arm64/kernel/entry.S:701 The buggy address belongs to the object at ffff23794dda0000 which belongs to the cache pid of size 224 The buggy address is located 4 bytes inside of 224-byte region [ff ---truncated---

In the Linux kernel, the following vulnerability has been resolved: block: avoid to reuse `hctx` not removed from cpuhp callback list If the 'hctx' isn't removed from cpuhp callback list, we can't reuse it, otherwise use-after-free may be triggered.

In the Linux kernel, the following vulnerability has been resolved: scsi: iscsi: Fix iscsi_task use after free Commit d39df158518c ("scsi: iscsi: Have abort handler get ref to conn") added iscsi_get_conn()/iscsi_put_conn() calls during abort handling but then also changed the handling of the case where we detect an already completed task where we now end up doing a goto to the common put/cleanup code. This results in a iscsi_task use after free, because the common cleanup code will do a put on the iscsi_task. This reverts the goto and moves the iscsi_get_conn() to after we've checked if the iscsi_task is valid.

In the Linux kernel, the following vulnerability has been resolved: ethernet:enic: Fix a use after free bug in enic_hard_start_xmit In enic_hard_start_xmit, it calls enic_queue_wq_skb(). Inside enic_queue_wq_skb, if some error happens, the skb will be freed by dev_kfree_skb(skb). But the freed skb is still used in skb_tx_timestamp(skb). My patch makes enic_queue_wq_skb() return error and goto spin_unlock() incase of error. The solution is provided by Govind. See https://lkml.org/lkml/2021/4/30/961.

In the Linux kernel, the following vulnerability has been resolved: KVM: PPC: Book3S HV: Prevent UAF in kvm_spapr_tce_attach_iommu_group() Al reported a possible use-after-free (UAF) in kvm_spapr_tce_attach_iommu_group(). It looks up `stt` from tablefd, but then continues to use it after doing fdput() on the returned fd. After the fdput() the tablefd is free to be closed by another thread. The close calls kvm_spapr_tce_release() and then release_spapr_tce_table() (via call_rcu()) which frees `stt`. Although there are calls to rcu_read_lock() in kvm_spapr_tce_attach_iommu_group() they are not sufficient to prevent the UAF, because `stt` is used outside the locked regions. With an artifcial delay after the fdput() and a userspace program which triggers the race, KASAN detects the UAF: BUG: KASAN: slab-use-after-free in kvm_spapr_tce_attach_iommu_group+0x298/0x720 [kvm] Read of size 4 at addr c000200027552c30 by task kvm-vfio/2505 CPU: 54 PID: 2505 Comm: kvm-vfio Not tainted 6.10.0-rc3-next-20240612-dirty #1 Hardware name: 8335-GTH POWER9 0x4e1202 opal:skiboot-v6.5.3-35-g1851b2a06 PowerNV Call Trace: dump_stack_lvl+0xb4/0x108 (unreliable) print_report+0x2b4/0x6ec kasan_report+0x118/0x2b0 __asan_load4+0xb8/0xd0 kvm_spapr_tce_attach_iommu_group+0x298/0x720 [kvm] kvm_vfio_set_attr+0x524/0xac0 [kvm] kvm_device_ioctl+0x144/0x240 [kvm] sys_ioctl+0x62c/0x1810 system_call_exception+0x190/0x440 system_call_vectored_common+0x15c/0x2ec ... Freed by task 0: ... kfree+0xec/0x3e0 release_spapr_tce_table+0xd4/0x11c [kvm] rcu_core+0x568/0x16a0 handle_softirqs+0x23c/0x920 do_softirq_own_stack+0x6c/0x90 do_softirq_own_stack+0x58/0x90 __irq_exit_rcu+0x218/0x2d0 irq_exit+0x30/0x80 arch_local_irq_restore+0x128/0x230 arch_local_irq_enable+0x1c/0x30 cpuidle_enter_state+0x134/0x5cc cpuidle_enter+0x6c/0xb0 call_cpuidle+0x7c/0x100 do_idle+0x394/0x410 cpu_startup_entry+0x60/0x70 start_secondary+0x3fc/0x410 start_secondary_prolog+0x10/0x14 Fix it by delaying the fdput() until `stt` is no longer in use, which is effectively the entire function. To keep the patch minimal add a call to fdput() at each of the existing return paths. Future work can convert the function to goto or __cleanup style cleanup. With the fix in place the test case no longer triggers the UAF.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: add missing check for inode numbers on directory entries Syzbot reported that mounting and unmounting a specific pattern of corrupted nilfs2 filesystem images causes a use-after-free of metadata file inodes, which triggers a kernel bug in lru_add_fn(). As Jan Kara pointed out, this is because the link count of a metadata file gets corrupted to 0, and nilfs_evict_inode(), which is called from iput(), tries to delete that inode (ifile inode in this case). The inconsistency occurs because directories containing the inode numbers of these metadata files that should not be visible in the namespace are read without checking. Fix this issue by treating the inode numbers of these internal files as errors in the sanity check helper when reading directory folios/pages. Also thanks to Hillf Danton and Matthew Wilcox for their initial mm-layer analysis.

In the Linux kernel, the following vulnerability has been resolved: drm/i915/gt: Fix potential UAF by revoke of fence registers CI has been sporadically reporting the following issue triggered by igt@i915_selftest@live@hangcheck on ADL-P and similar machines: <6> [414.049203] i915: Running intel_hangcheck_live_selftests/igt_reset_evict_fence ... <6> [414.068804] i915 0000:00:02.0: [drm] GT0: GUC: submission enabled <6> [414.068812] i915 0000:00:02.0: [drm] GT0: GUC: SLPC enabled <3> [414.070354] Unable to pin Y-tiled fence; err:-4 <3> [414.071282] i915_vma_revoke_fence:301 GEM_BUG_ON(!i915_active_is_idle(&fence->active)) ... <4>[ 609.603992] ------------[ cut here ]------------ <2>[ 609.603995] kernel BUG at drivers/gpu/drm/i915/gt/intel_ggtt_fencing.c:301! <4>[ 609.604003] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI <4>[ 609.604006] CPU: 0 PID: 268 Comm: kworker/u64:3 Tainted: G U W 6.9.0-CI_DRM_14785-g1ba62f8cea9c+ #1 <4>[ 609.604008] Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-P DDR4 RVP, BIOS RPLPFWI1.R00.4035.A00.2301200723 01/20/2023 <4>[ 609.604010] Workqueue: i915 __i915_gem_free_work [i915] <4>[ 609.604149] RIP: 0010:i915_vma_revoke_fence+0x187/0x1f0 [i915] ... <4>[ 609.604271] Call Trace: <4>[ 609.604273] <TASK> ... <4>[ 609.604716] __i915_vma_evict+0x2e9/0x550 [i915] <4>[ 609.604852] __i915_vma_unbind+0x7c/0x160 [i915] <4>[ 609.604977] force_unbind+0x24/0xa0 [i915] <4>[ 609.605098] i915_vma_destroy+0x2f/0xa0 [i915] <4>[ 609.605210] __i915_gem_object_pages_fini+0x51/0x2f0 [i915] <4>[ 609.605330] __i915_gem_free_objects.isra.0+0x6a/0xc0 [i915] <4>[ 609.605440] process_scheduled_works+0x351/0x690 ... In the past, there were similar failures reported by CI from other IGT tests, observed on other platforms. Before commit 63baf4f3d587 ("drm/i915/gt: Only wait for GPU activity before unbinding a GGTT fence"), i915_vma_revoke_fence() was waiting for idleness of vma->active via fence_update(). That commit introduced vma->fence->active in order for the fence_update() to be able to wait selectively on that one instead of vma->active since only idleness of fence registers was needed. But then, another commit 0d86ee35097a ("drm/i915/gt: Make fence revocation unequivocal") replaced the call to fence_update() in i915_vma_revoke_fence() with only fence_write(), and also added that GEM_BUG_ON(!i915_active_is_idle(&fence->active)) in front. No justification was provided on why we might then expect idleness of vma->fence->active without first waiting on it. The issue can be potentially caused by a race among revocation of fence registers on one side and sequential execution of signal callbacks invoked on completion of a request that was using them on the other, still processed in parallel to revocation of those fence registers. Fix it by waiting for idleness of vma->fence->active in i915_vma_revoke_fence(). (cherry picked from commit 24bb052d3dd499c5956abad5f7d8e4fd07da7fb1)

In the Linux kernel, the following vulnerability has been resolved: ASoC: topology: Fix references to freed memory Most users after parsing a topology file, release memory used by it, so having pointer references directly into topology file contents is wrong. Use devm_kmemdup(), to allocate memory as needed.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: wait for ondemand_object_worker to finish when dropping object When queuing ondemand_object_worker() to re-open the object, cachefiles_object is not pinned. The cachefiles_object may be freed when the pending read request is completed intentionally and the related erofs is umounted. If ondemand_object_worker() runs after the object is freed, it will incur use-after-free problem as shown below. process A processs B process C process D cachefiles_ondemand_send_req() // send a read req X // wait for its completion // close ondemand fd cachefiles_ondemand_fd_release() // set object as CLOSE cachefiles_ondemand_daemon_read() // set object as REOPENING queue_work(fscache_wq, &info->ondemand_work) // close /dev/cachefiles cachefiles_daemon_release cachefiles_flush_reqs complete(&req->done) // read req X is completed // umount the erofs fs cachefiles_put_object() // object will be freed cachefiles_ondemand_deinit_obj_info() kmem_cache_free(object) // both info and object are freed ondemand_object_worker() When dropping an object, it is no longer necessary to reopen the object, so use cancel_work_sync() to cancel or wait for ondemand_object_worker() to finish.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: Set object to close if ondemand_id < 0 in copen If copen is maliciously called in the user mode, it may delete the request corresponding to the random id. And the request may have not been read yet. Note that when the object is set to reopen, the open request will be done with the still reopen state in above case. As a result, the request corresponding to this object is always skipped in select_req function, so the read request is never completed and blocks other process. Fix this issue by simply set object to close if its id < 0 in copen.

In the Linux kernel, the following vulnerability has been resolved: ath10k: Fix a use after free in ath10k_htc_send_bundle In ath10k_htc_send_bundle, the bundle_skb could be freed by dev_kfree_skb_any(bundle_skb). But the bundle_skb is used later by bundle_skb->len. As skb_len = bundle_skb->len, my patch replaces bundle_skb->len to skb_len after the bundle_skb was freed.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix inode number range checks Patch series "nilfs2: fix potential issues related to reserved inodes". This series fixes one use-after-free issue reported by syzbot, caused by nilfs2's internal inode being exposed in the namespace on a corrupted filesystem, and a couple of flaws that cause problems if the starting number of non-reserved inodes written in the on-disk super block is intentionally (or corruptly) changed from its default value. This patch (of 3): In the current implementation of nilfs2, "nilfs->ns_first_ino", which gives the first non-reserved inode number, is read from the superblock, but its lower limit is not checked. As a result, if a number that overlaps with the inode number range of reserved inodes such as the root directory or metadata files is set in the super block parameter, the inode number test macros (NILFS_MDT_INODE and NILFS_VALID_INODE) will not function properly. In addition, these test macros use left bit-shift calculations using with the inode number as the shift count via the BIT macro, but the result of a shift calculation that exceeds the bit width of an integer is undefined in the C specification, so if "ns_first_ino" is set to a large value other than the default value NILFS_USER_INO (=11), the macros may potentially malfunction depending on the environment. Fix these issues by checking the lower bound of "nilfs->ns_first_ino" and by preventing bit shifts equal to or greater than the NILFS_USER_INO constant in the inode number test macros. Also, change the type of "ns_first_ino" from signed integer to unsigned integer to avoid the need for type casting in comparisons such as the lower bound check introduced this time.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: fix slab-use-after-free in fscache_withdraw_volume() We got the following issue in our fault injection stress test: ================================================================== BUG: KASAN: slab-use-after-free in fscache_withdraw_volume+0x2e1/0x370 Read of size 4 at addr ffff88810680be08 by task ondemand-04-dae/5798 CPU: 0 PID: 5798 Comm: ondemand-04-dae Not tainted 6.8.0-dirty #565 Call Trace: kasan_check_range+0xf6/0x1b0 fscache_withdraw_volume+0x2e1/0x370 cachefiles_withdraw_volume+0x31/0x50 cachefiles_withdraw_cache+0x3ad/0x900 cachefiles_put_unbind_pincount+0x1f6/0x250 cachefiles_daemon_release+0x13b/0x290 __fput+0x204/0xa00 task_work_run+0x139/0x230 Allocated by task 5820: __kmalloc+0x1df/0x4b0 fscache_alloc_volume+0x70/0x600 __fscache_acquire_volume+0x1c/0x610 erofs_fscache_register_volume+0x96/0x1a0 erofs_fscache_register_fs+0x49a/0x690 erofs_fc_fill_super+0x6c0/0xcc0 vfs_get_super+0xa9/0x140 vfs_get_tree+0x8e/0x300 do_new_mount+0x28c/0x580 [...] Freed by task 5820: kfree+0xf1/0x2c0 fscache_put_volume.part.0+0x5cb/0x9e0 erofs_fscache_unregister_fs+0x157/0x1b0 erofs_kill_sb+0xd9/0x1c0 deactivate_locked_super+0xa3/0x100 vfs_get_super+0x105/0x140 vfs_get_tree+0x8e/0x300 do_new_mount+0x28c/0x580 [...] ================================================================== Following is the process that triggers the issue: mount failed | daemon exit ------------------------------------------------------------ deactivate_locked_super cachefiles_daemon_release erofs_kill_sb erofs_fscache_unregister_fs fscache_relinquish_volume __fscache_relinquish_volume fscache_put_volume(fscache_volume, fscache_volume_put_relinquish) zero = __refcount_dec_and_test(&fscache_volume->ref, &ref); cachefiles_put_unbind_pincount cachefiles_daemon_unbind cachefiles_withdraw_cache cachefiles_withdraw_volumes list_del_init(&volume->cache_link) fscache_free_volume(fscache_volume) cache->ops->free_volume cachefiles_free_volume list_del_init(&cachefiles_volume->cache_link); kfree(fscache_volume) cachefiles_withdraw_volume fscache_withdraw_volume fscache_volume->n_accesses // fscache_volume UAF !!! The fscache_volume in cache->volumes must not have been freed yet, but its reference count may be 0. So use the new fscache_try_get_volume() helper function try to get its reference count. If the reference count of fscache_volume is 0, fscache_put_volume() is freeing it, so wait for it to be removed from cache->volumes. If its reference count is not 0, call cachefiles_withdraw_volume() with reference count protection to avoid the above issue.

In the Linux kernel, the following vulnerability has been resolved: ima: Fix use-after-free on a dentry's dname.name ->d_name.name can change on rename and the earlier value can be freed; there are conditions sufficient to stabilize it (->d_lock on dentry, ->d_lock on its parent, ->i_rwsem exclusive on the parent's inode, rename_lock), but none of those are met at any of the sites. Take a stable snapshot of the name instead.

In the Linux kernel, the following vulnerability has been resolved: xhci: Handle TD clearing for multiple streams case When multiple streams are in use, multiple TDs might be in flight when an endpoint is stopped. We need to issue a Set TR Dequeue Pointer for each, to ensure everything is reset properly and the caches cleared. Change the logic so that any N>1 TDs found active for different streams are deferred until after the first one is processed, calling xhci_invalidate_cancelled_tds() again from xhci_handle_cmd_set_deq() to queue another command until we are done with all of them. Also change the error/"should never happen" paths to ensure we at least clear any affected TDs, even if we can't issue a command to clear the hardware cache, and complain loudly with an xhci_warn() if this ever happens. This problem case dates back to commit e9df17eb1408 ("USB: xhci: Correct assumptions about number of rings per endpoint.") early on in the XHCI driver's life, when stream support was first added. It was then identified but not fixed nor made into a warning in commit 674f8438c121 ("xhci: split handling halted endpoints into two steps"), which added a FIXME comment for the problem case (without materially changing the behavior as far as I can tell, though the new logic made the problem more obvious). Then later, in commit 94f339147fc3 ("xhci: Fix failure to give back some cached cancelled URBs."), it was acknowledged again. [Mathias: commit 94f339147fc3 ("xhci: Fix failure to give back some cached cancelled URBs.") was a targeted regression fix to the previously mentioned patch. Users reported issues with usb stuck after unmounting/disconnecting UAS devices. This rolled back the TD clearing of multiple streams to its original state.] Apparently the commit author was aware of the problem (yet still chose to submit it): It was still mentioned as a FIXME, an xhci_dbg() was added to log the problem condition, and the remaining issue was mentioned in the commit description. The choice of making the log type xhci_dbg() for what is, at this point, a completely unhandled and known broken condition is puzzling and unfortunate, as it guarantees that no actual users would see the log in production, thereby making it nigh undebuggable (indeed, even if you turn on DEBUG, the message doesn't really hint at there being a problem at all). It took me *months* of random xHC crashes to finally find a reliable repro and be able to do a deep dive debug session, which could all have been avoided had this unhandled, broken condition been actually reported with a warning, as it should have been as a bug intentionally left in unfixed (never mind that it shouldn't have been left in at all). > Another fix to solve clearing the caches of all stream rings with > cancelled TDs is needed, but not as urgent. 3 years after that statement and 14 years after the original bug was introduced, I think it's finally time to fix it. And maybe next time let's not leave bugs unfixed (that are actually worse than the original bug), and let's actually get people to review kernel commits please. Fixes xHC crashes and IOMMU faults with UAS devices when handling errors/faults. Easiest repro is to use `hdparm` to mark an early sector (e.g. 1024) on a disk as bad, then `cat /dev/sdX > /dev/null` in a loop. At least in the case of JMicron controllers, the read errors end up having to cancel two TDs (for two queued requests to different streams) and the one that didn't get cleared properly ends up faulting the xHC entirely when it tries to access DMA pages that have since been unmapped, referred to by the stale TDs. This normally happens quickly (after two or three loops). After this fix, I left the `cat` in a loop running overnight and experienced no xHC failures, with all read errors recovered properly. Repro'd and tested on an Apple M1 Mac Mini (dwc3 host). On systems without an IOMMU, this bug would instead silently corrupt freed memory, making this a ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ionic: fix use after netif_napi_del() When queues are started, netif_napi_add() and napi_enable() are called. If there are 4 queues and only 3 queues are used for the current configuration, only 3 queues' napi should be registered and enabled. The ionic_qcq_enable() checks whether the .poll pointer is not NULL for enabling only the using queue' napi. Unused queues' napi will not be registered by netif_napi_add(), so the .poll pointer indicates NULL. But it couldn't distinguish whether the napi was unregistered or not because netif_napi_del() doesn't reset the .poll pointer to NULL. So, ionic_qcq_enable() calls napi_enable() for the queue, which was unregistered by netif_napi_del(). Reproducer: ethtool -L <interface name> rx 1 tx 1 combined 0 ethtool -L <interface name> rx 0 tx 0 combined 1 ethtool -L <interface name> rx 0 tx 0 combined 4 Splat looks like: kernel BUG at net/core/dev.c:6666! Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 3 PID: 1057 Comm: kworker/3:3 Not tainted 6.10.0-rc2+ #16 Workqueue: events ionic_lif_deferred_work [ionic] RIP: 0010:napi_enable+0x3b/0x40 Code: 48 89 c2 48 83 e2 f6 80 b9 61 09 00 00 00 74 0d 48 83 bf 60 01 00 00 00 74 03 80 ce 01 f0 4f RSP: 0018:ffffb6ed83227d48 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff97560cda0828 RCX: 0000000000000029 RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff97560cda0a28 RBP: ffffb6ed83227d50 R08: 0000000000000400 R09: 0000000000000001 R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000000 R13: ffff97560ce3c1a0 R14: 0000000000000000 R15: ffff975613ba0a20 FS: 0000000000000000(0000) GS:ffff975d5f780000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f8f734ee200 CR3: 0000000103e50000 CR4: 00000000007506f0 PKRU: 55555554 Call Trace: <TASK> ? die+0x33/0x90 ? do_trap+0xd9/0x100 ? napi_enable+0x3b/0x40 ? do_error_trap+0x83/0xb0 ? napi_enable+0x3b/0x40 ? napi_enable+0x3b/0x40 ? exc_invalid_op+0x4e/0x70 ? napi_enable+0x3b/0x40 ? asm_exc_invalid_op+0x16/0x20 ? napi_enable+0x3b/0x40 ionic_qcq_enable+0xb7/0x180 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_start_queues+0xc4/0x290 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_link_status_check+0x11c/0x170 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_lif_deferred_work+0x129/0x280 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] process_one_work+0x145/0x360 worker_thread+0x2bb/0x3d0 ? __pfx_worker_thread+0x10/0x10 kthread+0xcc/0x100 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2d/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30

In the Linux kernel, the following vulnerability has been resolved: cachefiles: defer exposing anon_fd until after copy_to_user() succeeds After installing the anonymous fd, we can now see it in userland and close it. However, at this point we may not have gotten the reference count of the cache, but we will put it during colse fd, so this may cause a cache UAF. So grab the cache reference count before fd_install(). In addition, by kernel convention, fd is taken over by the user land after fd_install(), and the kernel should not call close_fd() after that, i.e., it should call fd_install() after everything is ready, thus fd_install() is called after copy_to_user() succeeds.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: remove requests from xarray during flushing requests Even with CACHEFILES_DEAD set, we can still read the requests, so in the following concurrency the request may be used after it has been freed: mount | daemon_thread1 | daemon_thread2 ------------------------------------------------------------ cachefiles_ondemand_init_object cachefiles_ondemand_send_req REQ_A = kzalloc(sizeof(*req) + data_len) wait_for_completion(&REQ_A->done) cachefiles_daemon_read cachefiles_ondemand_daemon_read // close dev fd cachefiles_flush_reqs complete(&REQ_A->done) kfree(REQ_A) xa_lock(&cache->reqs); cachefiles_ondemand_select_req req->msg.opcode != CACHEFILES_OP_READ // req use-after-free !!! xa_unlock(&cache->reqs); xa_destroy(&cache->reqs) Hence remove requests from cache->reqs when flushing them to avoid accessing freed requests.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: fix slab-use-after-free in cachefiles_ondemand_daemon_read() We got the following issue in a fuzz test of randomly issuing the restore command: ================================================================== BUG: KASAN: slab-use-after-free in cachefiles_ondemand_daemon_read+0xb41/0xb60 Read of size 8 at addr ffff888122e84088 by task ondemand-04-dae/963 CPU: 13 PID: 963 Comm: ondemand-04-dae Not tainted 6.8.0-dirty #564 Call Trace: kasan_report+0x93/0xc0 cachefiles_ondemand_daemon_read+0xb41/0xb60 vfs_read+0x169/0xb50 ksys_read+0xf5/0x1e0 Allocated by task 116: kmem_cache_alloc+0x140/0x3a0 cachefiles_lookup_cookie+0x140/0xcd0 fscache_cookie_state_machine+0x43c/0x1230 [...] Freed by task 792: kmem_cache_free+0xfe/0x390 cachefiles_put_object+0x241/0x480 fscache_cookie_state_machine+0x5c8/0x1230 [...] ================================================================== Following is the process that triggers the issue: mount | daemon_thread1 | daemon_thread2 ------------------------------------------------------------ cachefiles_withdraw_cookie cachefiles_ondemand_clean_object(object) cachefiles_ondemand_send_req REQ_A = kzalloc(sizeof(*req) + data_len) wait_for_completion(&REQ_A->done) cachefiles_daemon_read cachefiles_ondemand_daemon_read REQ_A = cachefiles_ondemand_select_req msg->object_id = req->object->ondemand->ondemand_id ------ restore ------ cachefiles_ondemand_restore xas_for_each(&xas, req, ULONG_MAX) xas_set_mark(&xas, CACHEFILES_REQ_NEW) cachefiles_daemon_read cachefiles_ondemand_daemon_read REQ_A = cachefiles_ondemand_select_req copy_to_user(_buffer, msg, n) xa_erase(&cache->reqs, id) complete(&REQ_A->done) ------ close(fd) ------ cachefiles_ondemand_fd_release cachefiles_put_object cachefiles_put_object kmem_cache_free(cachefiles_object_jar, object) REQ_A->object->ondemand->ondemand_id // object UAF !!! When we see the request within xa_lock, req->object must not have been freed yet, so grab the reference count of object before xa_unlock to avoid the above issue.

In the Linux kernel, the following vulnerability has been resolved: btrfs: zoned: fix use-after-free due to race with dev replace While loading a zone's info during creation of a block group, we can race with a device replace operation and then trigger a use-after-free on the device that was just replaced (source device of the replace operation). This happens because at btrfs_load_zone_info() we extract a device from the chunk map into a local variable and then use the device while not under the protection of the device replace rwsem. So if there's a device replace operation happening when we extract the device and that device is the source of the replace operation, we will trigger a use-after-free if before we finish using the device the replace operation finishes and frees the device. Fix this by enlarging the critical section under the protection of the device replace rwsem so that all uses of the device are done inside the critical section.

In the Linux kernel, the following vulnerability has been resolved: net: wwan: iosm: Fix tainted pointer delete is case of region creation fail In case of region creation fail in ipc_devlink_create_region(), previously created regions delete process starts from tainted pointer which actually holds error code value. Fix this bug by decreasing region index before delete. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: net: bridge: mst: fix suspicious rcu usage in br_mst_set_state I converted br_mst_set_state to RCU to avoid a vlan use-after-free but forgot to change the vlan group dereference helper. Switch to vlan group RCU deref helper to fix the suspicious rcu usage warning.

In the Linux kernel, the following vulnerability has been resolved: greybus: Fix use-after-free bug in gb_interface_release due to race condition. In gb_interface_create, &intf->mode_switch_completion is bound with gb_interface_mode_switch_work. Then it will be started by gb_interface_request_mode_switch. Here is the relevant code. if (!queue_work(system_long_wq, &intf->mode_switch_work)) { ... } If we call gb_interface_release to make cleanup, there may be an unfinished work. This function will call kfree to free the object "intf". However, if gb_interface_mode_switch_work is scheduled to run after kfree, it may cause use-after-free error as gb_interface_mode_switch_work will use the object "intf". The possible execution flow that may lead to the issue is as follows: CPU0 CPU1 | gb_interface_create | gb_interface_request_mode_switch gb_interface_release | kfree(intf) (free) | | gb_interface_mode_switch_work | mutex_lock(&intf->mutex) (use) Fix it by canceling the work before kfree.

In drivers/net/ethernet/hisilicon/hns/hns_enet.c in the Linux kernel before 4.13, local users can cause a denial of service (use-after-free and BUG) or possibly have unspecified other impact by leveraging differences in skb handling between hns_nic_net_xmit_hw and hns_nic_net_xmit.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/mes: fix use-after-free issue Delete fence fallback timer to fix the ramdom use-after-free issue. v2: move to amdgpu_mes.c

In the Linux kernel, the following vulnerability has been resolved: dmaengine: idxd: Avoid unnecessary destruction of file_ida file_ida is allocated during cdev open and is freed accordingly during cdev release. This sequence is guaranteed by driver file operations. Therefore, there is no need to destroy an already empty file_ida when the WQ cdev is removed. Worse, ida_free() in cdev release may happen after destruction of file_ida per WQ cdev. This can lead to accessing an id in file_ida after it has been destroyed, resulting in a kernel panic. Remove ida_destroy(&file_ida) to address these issues.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Discard command completions in internal error Fix use after free when FW completion arrives while device is in internal error state. Avoid calling completion handler in this case, since the device will flush the command interface and trigger all completions manually. Kernel log: ------------[ cut here ]------------ refcount_t: underflow; use-after-free. ... RIP: 0010:refcount_warn_saturate+0xd8/0xe0 ... Call Trace: <IRQ> ? __warn+0x79/0x120 ? refcount_warn_saturate+0xd8/0xe0 ? report_bug+0x17c/0x190 ? handle_bug+0x3c/0x60 ? exc_invalid_op+0x14/0x70 ? asm_exc_invalid_op+0x16/0x20 ? refcount_warn_saturate+0xd8/0xe0 cmd_ent_put+0x13b/0x160 [mlx5_core] mlx5_cmd_comp_handler+0x5f9/0x670 [mlx5_core] cmd_comp_notifier+0x1f/0x30 [mlx5_core] notifier_call_chain+0x35/0xb0 atomic_notifier_call_chain+0x16/0x20 mlx5_eq_async_int+0xf6/0x290 [mlx5_core] notifier_call_chain+0x35/0xb0 atomic_notifier_call_chain+0x16/0x20 irq_int_handler+0x19/0x30 [mlx5_core] __handle_irq_event_percpu+0x4b/0x160 handle_irq_event+0x2e/0x80 handle_edge_irq+0x98/0x230 __common_interrupt+0x3b/0xa0 common_interrupt+0x7b/0xa0 </IRQ> <TASK> asm_common_interrupt+0x22/0x40

The mm_init function in kernel/fork.c in the Linux kernel before 4.12.10 does not clear the ->exe_file member of a new process's mm_struct, allowing a local attacker to achieve a use-after-free or possibly have unspecified other impact by running a specially crafted program.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix UAF for cq async event The refcount of CQ is not protected by locks. When CQ asynchronous events and CQ destruction are concurrent, CQ may have been released, which will cause UAF. Use the xa_lock() to protect the CQ refcount.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix possible UAF when remounting r/o a mmp-protected file system After commit 618f003199c6 ("ext4: fix memory leak in ext4_fill_super"), after the file system is remounted read-only, there is a race where the kmmpd thread can exit, causing sbi->s_mmp_tsk to point at freed memory, which the call to ext4_stop_mmpd() can trip over. Fix this by only allowing kmmpd() to exit when it is stopped via ext4_stop_mmpd(). Bug-Report-Link: <20210629143603.2166962-1-yebin10@huawei.com>

In the Linux kernel, the following vulnerability has been resolved: gfs2: Fix potential glock use-after-free on unmount When a DLM lockspace is released and there ares still locks in that lockspace, DLM will unlock those locks automatically. Commit fb6791d100d1b started exploiting this behavior to speed up filesystem unmount: gfs2 would simply free glocks it didn't want to unlock and then release the lockspace. This didn't take the bast callbacks for asynchronous lock contention notifications into account, which remain active until until a lock is unlocked or its lockspace is released. To prevent those callbacks from accessing deallocated objects, put the glocks that should not be unlocked on the sd_dead_glocks list, release the lockspace, and only then free those glocks. As an additional measure, ignore unexpected ast and bast callbacks if the receiving glock is dead.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix use-after-free of timer for log writer thread Patch series "nilfs2: fix log writer related issues". This bug fix series covers three nilfs2 log writer-related issues, including a timer use-after-free issue and potential deadlock issue on unmount, and a potential freeze issue in event synchronization found during their analysis. Details are described in each commit log. This patch (of 3): A use-after-free issue has been reported regarding the timer sc_timer on the nilfs_sc_info structure. The problem is that even though it is used to wake up a sleeping log writer thread, sc_timer is not shut down until the nilfs_sc_info structure is about to be freed, and is used regardless of the thread's lifetime. Fix this issue by limiting the use of sc_timer only while the log writer thread is alive.

The XFRM dump policy implementation in net/xfrm/xfrm_user.c in the Linux kernel before 4.13.11 allows local users to gain privileges or cause a denial of service (use-after-free) via a crafted SO_RCVBUF setsockopt system call in conjunction with XFRM_MSG_GETPOLICY Netlink messages.

In the Linux kernel, the following vulnerability has been resolved: net: dpaa2-eth: fix use-after-free in dpaa2_eth_remove Access to netdev after free_netdev() will cause use-after-free bug. Move debug log before free_netdev() call to avoid it.

In the Linux kernel, the following vulnerability has been resolved: drivers/virt/acrn: fix PFNMAP PTE checks in acrn_vm_ram_map() Patch series "mm: follow_pte() improvements and acrn follow_pte() fixes". Patch #1 fixes a bunch of issues I spotted in the acrn driver. It compiles, that's all I know. I'll appreciate some review and testing from acrn folks. Patch #2+#3 improve follow_pte(), passing a VMA instead of the MM, adding more sanity checks, and improving the documentation. Gave it a quick test on x86-64 using VM_PAT that ends up using follow_pte(). This patch (of 3): We currently miss handling various cases, resulting in a dangerous follow_pte() (previously follow_pfn()) usage. (1) We're not checking PTE write permissions. Maybe we should simply always require pte_write() like we do for pin_user_pages_fast(FOLL_WRITE)? Hard to tell, so let's check for ACRN_MEM_ACCESS_WRITE for now. (2) We're not rejecting refcounted pages. As we are not using MMU notifiers, messing with refcounted pages is dangerous and can result in use-after-free. Let's make sure to reject them. (3) We are only looking at the first PTE of a bigger range. We only lookup a single PTE, but memmap->len may span a larger area. Let's loop over all involved PTEs and make sure the PFN range is actually contiguous. Reject everything else: it couldn't have worked either way, and rather made use access PFNs we shouldn't be accessing.

In the Linux kernel, the following vulnerability has been resolved: ftrace: Fix possible use-after-free issue in ftrace_location() KASAN reports a bug: BUG: KASAN: use-after-free in ftrace_location+0x90/0x120 Read of size 8 at addr ffff888141d40010 by task insmod/424 CPU: 8 PID: 424 Comm: insmod Tainted: G W 6.9.0-rc2+ [...] Call Trace: <TASK> dump_stack_lvl+0x68/0xa0 print_report+0xcf/0x610 kasan_report+0xb5/0xe0 ftrace_location+0x90/0x120 register_kprobe+0x14b/0xa40 kprobe_init+0x2d/0xff0 [kprobe_example] do_one_initcall+0x8f/0x2d0 do_init_module+0x13a/0x3c0 load_module+0x3082/0x33d0 init_module_from_file+0xd2/0x130 __x64_sys_finit_module+0x306/0x440 do_syscall_64+0x68/0x140 entry_SYSCALL_64_after_hwframe+0x71/0x79 The root cause is that, in lookup_rec(), ftrace record of some address is being searched in ftrace pages of some module, but those ftrace pages at the same time is being freed in ftrace_release_mod() as the corresponding module is being deleted: CPU1 | CPU2 register_kprobes() { | delete_module() { check_kprobe_address_safe() { | arch_check_ftrace_location() { | ftrace_location() { | lookup_rec() // USE! | ftrace_release_mod() // Free! To fix this issue: 1. Hold rcu lock as accessing ftrace pages in ftrace_location_range(); 2. Use ftrace_location_range() instead of lookup_rec() in ftrace_location(); 3. Call synchronize_rcu() before freeing any ftrace pages both in ftrace_process_locs()/ftrace_release_mod()/ftrace_free_mem().

In the Linux kernel, the following vulnerability has been resolved: atm: nicstar: Fix possible use-after-free in nicstar_cleanup() This module's remove path calls del_timer(). However, that function does not wait until the timer handler finishes. This means that the timer handler may still be running after the driver's remove function has finished, which would result in a use-after-free. Fix by calling del_timer_sync(), which makes sure the timer handler has finished, and unable to re-schedule itself.

In the Linux kernel, the following vulnerability has been resolved: atm: iphase: fix possible use-after-free in ia_module_exit() This module's remove path calls del_timer(). However, that function does not wait until the timer handler finishes. This means that the timer handler may still be running after the driver's remove function has finished, which would result in a use-after-free. Fix by calling del_timer_sync(), which makes sure the timer handler has finished, and unable to re-schedule itself.

In the Linux Kernel before versions 4.20.8 and 4.19.21 a use-after-free error in the "sctp_sendmsg()" function (net/sctp/socket.c) when handling SCTP_SENDALL flag can be exploited to corrupt memory.

In the Linux kernel, the following vulnerability has been resolved: drm/prime: Fix use after free in mmap with drm_gem_ttm_mmap drm_gem_ttm_mmap() drops a reference to the gem object on success. If the gem object's refcount == 1 on entry to drm_gem_prime_mmap(), that drop will free the gem object, and the subsequent drm_gem_object_get() will be a UAF. Fix by grabbing a reference before calling the mmap helper. This issue was forseen when the reference dropping was adding in commit 9786b65bc61ac ("drm/ttm: fix mmap refcounting"): "For that to work properly the drm_gem_object_get() call in drm_gem_ttm_mmap() must be moved so it happens before calling obj->funcs->mmap(), otherwise the gem refcount would go down to zero."

In the Linux kernel, the following vulnerability has been resolved: can: j1939: j1939_netdev_start(): fix UAF for rx_kref of j1939_priv It will trigger UAF for rx_kref of j1939_priv as following. cpu0 cpu1 j1939_sk_bind(socket0, ndev0, ...) j1939_netdev_start j1939_sk_bind(socket1, ndev0, ...) j1939_netdev_start j1939_priv_set j1939_priv_get_by_ndev_locked j1939_jsk_add ..... j1939_netdev_stop kref_put_lock(&priv->rx_kref, ...) kref_get(&priv->rx_kref, ...) REFCOUNT_WARN("addition on 0;...") ==================================================== refcount_t: addition on 0; use-after-free. WARNING: CPU: 1 PID: 20874 at lib/refcount.c:25 refcount_warn_saturate+0x169/0x1e0 RIP: 0010:refcount_warn_saturate+0x169/0x1e0 Call Trace: j1939_netdev_start+0x68b/0x920 j1939_sk_bind+0x426/0xeb0 ? security_socket_bind+0x83/0xb0 The rx_kref's kref_get() and kref_put() should use j1939_netdev_lock to protect.

In the Linux kernel, the following vulnerability has been resolved: regmap: set debugfs_name to NULL after it is freed There is a upstream commit cffa4b2122f5("regmap:debugfs: Fix a memory leak when calling regmap_attach_dev") that adds a if condition when create name for debugfs_name. With below function invoking logical, debugfs_name is freed in regmap_debugfs_exit(), but it is not created again because of the if condition introduced by above commit. regmap_reinit_cache() regmap_debugfs_exit() ... regmap_debugfs_init() So, set debugfs_name to NULL after it is freed.

The sctp_do_peeloff function in net/sctp/socket.c in the Linux kernel before 4.14 does not check whether the intended netns is used in a peel-off action, which allows local users to cause a denial of service (use-after-free and system crash) or possibly have unspecified other impact via crafted system calls.

In the Linux kernel, the following vulnerability has been resolved: staging: greybus: uart: fix tty use after free User space can hold a tty open indefinitely and tty drivers must not release the underlying structures until the last user is gone. Switch to using the tty-port reference counter to manage the life time of the greybus tty state to avoid use after free after a disconnect.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: msft: fix slab-use-after-free in msft_do_close() Tying the msft->data lifetime to hdev by freeing it in hci_release_dev() to fix the following case: [use] msft_do_close() msft = hdev->msft_data; if (!msft) ...(1) <- passed. return; mutex_lock(&msft->filter_lock); ...(4) <- used after freed. [free] msft_unregister() msft = hdev->msft_data; hdev->msft_data = NULL; ...(2) kfree(msft); ...(3) <- msft is freed. ================================================================== BUG: KASAN: slab-use-after-free in __mutex_lock_common kernel/locking/mutex.c:587 [inline] BUG: KASAN: slab-use-after-free in __mutex_lock+0x8f/0xc30 kernel/locking/mutex.c:752 Read of size 8 at addr ffff888106cbbca8 by task kworker/u5:2/309

In the Linux kernel, the following vulnerability has been resolved: raid1: fix use-after-free for original bio in raid1_write_request() r1_bio->bios[] is used to record new bios that will be issued to underlying disks, however, in raid1_write_request(), r1_bio->bios[] will set to the original bio temporarily. Meanwhile, if blocked rdev is set, free_r1bio() will be called causing that all r1_bio->bios[] to be freed: raid1_write_request() r1_bio = alloc_r1bio(mddev, bio); -> r1_bio->bios[] is NULL for (i = 0; i < disks; i++) -> for each rdev in conf // first rdev is normal r1_bio->bios[0] = bio; -> set to original bio // second rdev is blocked if (test_bit(Blocked, &rdev->flags)) break if (blocked_rdev) free_r1bio() put_all_bios() bio_put(r1_bio->bios[0]) -> original bio is freed Test scripts: mdadm -CR /dev/md0 -l1 -n4 /dev/sd[abcd] --assume-clean fio -filename=/dev/md0 -ioengine=libaio -rw=write -bs=4k -numjobs=1 \ -iodepth=128 -name=test -direct=1 echo blocked > /sys/block/md0/md/rd2/state Test result: BUG bio-264 (Not tainted): Object already free ----------------------------------------------------------------------------- Allocated in mempool_alloc_slab+0x24/0x50 age=1 cpu=1 pid=869 kmem_cache_alloc+0x324/0x480 mempool_alloc_slab+0x24/0x50 mempool_alloc+0x6e/0x220 bio_alloc_bioset+0x1af/0x4d0 blkdev_direct_IO+0x164/0x8a0 blkdev_write_iter+0x309/0x440 aio_write+0x139/0x2f0 io_submit_one+0x5ca/0xb70 __do_sys_io_submit+0x86/0x270 __x64_sys_io_submit+0x22/0x30 do_syscall_64+0xb1/0x210 entry_SYSCALL_64_after_hwframe+0x6c/0x74 Freed in mempool_free_slab+0x1f/0x30 age=1 cpu=1 pid=869 kmem_cache_free+0x28c/0x550 mempool_free_slab+0x1f/0x30 mempool_free+0x40/0x100 bio_free+0x59/0x80 bio_put+0xf0/0x220 free_r1bio+0x74/0xb0 raid1_make_request+0xadf/0x1150 md_handle_request+0xc7/0x3b0 md_submit_bio+0x76/0x130 __submit_bio+0xd8/0x1d0 submit_bio_noacct_nocheck+0x1eb/0x5c0 submit_bio_noacct+0x169/0xd40 submit_bio+0xee/0x1d0 blkdev_direct_IO+0x322/0x8a0 blkdev_write_iter+0x309/0x440 aio_write+0x139/0x2f0 Since that bios for underlying disks are not allocated yet, fix this problem by using mempool_free() directly to free the r1_bio.

A use-after-free flaw was found in the Linux kernel’s Netfilter functionality when adding a rule with NFTA_RULE_CHAIN_ID. This flaw allows a local user to crash or escalate their privileges on the system.