An Improper Handling of Exceptional Conditions vulnerability in route processing of Juniper Networks Junos OS on specific end-of-life (EOL) ACX Series platforms allows an attacker to crash the Forwarding Engine Board (FEB) by flapping an interface, leading to a Denial of Service (DoS). On ACX1000, ACX1100, ACX2000, ACX2100, ACX2200, ACX4000, ACX5048, and ACX5096 devices, FEB0 will crash when the primary path port of the L2 circuit IGP (Interior Gateway Protocol) on the local device goes down. This issue is seen only when 'hot-standby' mode is configured for the L2 circuit. This issue affects Junos OS on ACX1000, ACX1100, ACX2000, ACX2100, ACX2200, ACX4000, ACX5048, and ACX5096:  * all versions before 21.2R3-S9.

An Improper Check for Unusual or Exceptional Conditions vulnerability in Juniper DHCP Daemon (jdhcpd) of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker to cause the jdhcpd to consume all the CPU cycles resulting in a Denial of Service (DoS). On Junos OS devices with forward-snooped-client configured, if an attacker sends a specific DHCP packet to a non-configured interface, this will cause an infinite loop. The DHCP process will have to be restarted to recover the service. This issue affects: Juniper Networks Junos OS * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S2; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R2.

An Improper Handling of Exceptional Conditions vulnerability in routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a local, low-privileged attacker executing a CLI command to cause a Denial of Service (DoS). When asregex-optimized is configured and a specific "show route as-path" CLI command is executed, the rpd crashes and restarts. Repeated execution of this command will cause a sustained DoS condition. This issue affects Junos OS: * All versions before 21.2R3-S9, * from 21.4 before 21.4R3-S10, * from 22.2 before 22.2R3-S6, * from 22.4 before 22.4R3-S6, * from 23.2 before 23.2R2-S3, * from 23.4 before 23.4R2-S4, * from 24.2 before 24.2R2. and Junos OS Evolved: * All versions before 21.2R3-S9-EVO, * from 21.4-EVO before 21.4R3-S10-EVO, * from 22.2-EVO before 22.2R3-S6-EVO, * from 22.4-EVO before 22.4R3-S6-EVO, * from 23.2-EVO before 23.2R2-S3-EVO, * from 23.4-EVO before 23.4R2-S4-EVO, * from 24.2-EVO before 24.2R2-EVO.

An Improper Handling of Exceptional Conditions vulnerability in packet processing of Juniper Networks Junos OS on MX Series allows an unauthenticated network-based attacker to send specific packets to an Aggregated Multiservices (AMS) interface on the device, causing the packet forwarding engine (PFE) to crash, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue is only triggered by packets destined to a local-interface via a service-interface (AMS). AMS is only supported on the MS-MPC, MS-MIC, and MX-SPC3 cards. This issue is not experienced on other types of interfaces or configurations. Additionally, transit traffic does not trigger this issue. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S12; 20.2 versions prior to 20.2R3-S8; 20.4 versions prior to 20.4R3-S7; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S5; 21.3 versions prior to 21.3R3-S4; 21.4 versions prior to 21.4R3-S3; 22.1 versions prior to 22.1R3-S2; 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R2-S1, 22.3R3; 22.4 versions prior to 22.4R1-S2, 22.4R2.

An Improper Handling of Exceptional Conditions vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated adjacent attacker sending a specific BGP update packet to cause rpd to crash and restart, resulting in a Denial of Service (DoS). Continuous receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects iBGP and eBGP, and both IPv4 and IPv6 are affected by this vulnerability. This issue affects Junos OS:  * from 21.4 before 21.4R3-S9,  * from 22.2 before 22.2R3-S5,  * from 22.3 before 22.3R3-S4, * from 22.4 before 22.4R3-S5,  * from 23.2 before 23.2R2-S3,  * from 23.4 before 23.4R2-S3,  * from 24.2 before 24.2R1-S2, 24.2R2;  This issue does not affect versions prior to 21.1R1. Junos OS Evolved:  * from 21.4 before 21.4R3-S9-EVO,  * from 22.2 before 22.2R3-S5-EVO,  * from 22.3 before 22.3R3-S4-EVO, * from 22.4 before 22.4R3-S5-EVO,  * from 23.2 before 23.2R2-S3-EVO,  * from 23.4 before 23.4R2-S3-EVO,  * from 24.2 before 24.2R1-S2-EVO, 24.2R2-EVO. This issue does not affect versions prior to 21.1R1-EVO

An Improper Handling of Exceptional Conditions vulnerability in the command-line processing of Juniper Networks Junos OS on SRX1500, SRX4100, and SRX4200 devices allows a local, low-privileged authenticated attacker executing the 'show chassis environment pem' command to cause the chassis daemon (chassisd) to crash and restart, resulting in a temporary Denial of Service (DoS). However, repeated execution of this command will eventually cause the chassisd process to fail to restart, impacting packet processing on the system. This issue affects Junos OS on SRX1500, SRX4100, SRX4200:  * All versions before 21.4R3-S9,  * from 22.2 before 22.2R3-S5,  * from 22.3 before 22.3R3-S4,  * from 22.4 before 22.4R3-S4,  * from 23.2 before 23.2R2-S3,  * from 23.4 before 23.4R2-S1.

The flowd process, responsible for forwarding traffic in SRX Series services gateways, may crash and restart when processing specific transit IP packets through an IPSec tunnel. Continued processing of these packets may result in an extended Denial of Service (DoS) condition. This issue only occurs when IPSec tunnels are configured. Systems without IPSec tunnel configurations are not vulnerable to this issue. This issue affects Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D171, 15.1X49-D180 on SRX Series; 18.2 versions 18.2R2-S1 and later, prior to 18.2R3 on SRX Series; 18.4 versions prior to 18.4R2 on SRX Series.

SSL-Proxy feature on SRX devices fails to handle a hardware resource limitation which can be exploited by remote SSL/TLS servers to crash the flowd daemon. Repeated crashes of the flowd daemon can result in an extended denial of service condition. For this issue to occur, clients protected by the SRX device must initiate a connection to the malicious server. This issue affects: Juniper Networks Junos OS on SRX5000 Series: 12.3X48 versions prior to 12.3X48-D85; 15.1X49 versions prior to 15.1X49-D180; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R2-S6, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R2; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R2.

An Improper Handling of Exceptional Conditions vulnerability in the Packet Forwarding Engine (pfe) of the Juniper Networks Junos OS Evolved on ACX Series devices allows an unauthenticated, network based attacker sending specific transit protocol traffic to cause a partial Denial of Service (DoS) to downstream devices. Receipt of specific transit protocol packets is incorrectly processed by the Routing Engine (RE), filling up the DDoS protection queue which is shared between routing protocols. This influx of transit protocol packets causes DDoS protection violations, resulting in protocol flaps which can affect connectivity to networking devices. This issue affects both IPv4 and IPv6. This issue does not require any specific routing protocol to be configured or enabled. The following commands can be used to monitor the DDoS protection queue:        labuser@re0> show evo-pfemand host pkt-stats     labuser@re0> show host-path ddos all-policers This issue affects Junos OS Evolved:  * All versions before 21.4R3-S8-EVO,  * from 22.2 before 22.2R3-S4-EVO,  * from 22.3 before 22.3R3-S4-EVO,  * from 22.4 before 22.4R3-S3-EVO,  * from 23.2 before 23.2R2-EVO,  * from 23.4 before 23.4R1-S1-EVO, 23.4R2-EVO,  * from 24.2 before 24.2R2-EVO.

A vulnerability in the processing of inbound IPv6 packets in Juniper Networks Junos OS on QFX5000 Series and EX4600 switches may cause the memory to not be freed, leading to a packet DMA memory leak, and eventual Denial of Service (DoS) condition. Once the condition occurs, further packet processing will be impacted, creating a sustained Denial of Service (DoS) condition. The following error logs may be observed using the "show heap" command and the device may eventually run out of memory if such packets are received continuously. Jan 12 12:00:00 device-name fpc0 (buf alloc) failed allocating packet buffer Jan 12 12:00:01 device-name fpc0 (buf alloc) failed allocating packet buffer user@device-name> request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 246fc1a8 536870488 353653752 183216736 34 Kernel 1 91800000 16777216 12069680 4707536 28 DMA 2 92800000 75497472 69997640 5499832 7 PKT DMA DESC 3 106fc000 335544320 221425960 114118360 34 Bcm_sdk 4 97000000 176160768 200 176160568 99 Packet DMA <<<<<<<<<<<<<< 5 903fffe0 20971504 20971504 0 0 Blob This issue affects Juniper Networks Junos OS on QFX5000 Series, EX4600: 18.3R3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S6; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue does not affect Juniper Networks Junos OS: Any versions prior to 17.4R3; 18.1 versions prior to 18.1R3-S6; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability combined with Improper Handling of Exceptional Conditions in Juniper Networks Junos OS on QFX Series and PTX Series allows an unauthenticated network based attacker to cause increased FPC CPU utilization by sending specific IP packets which are being VXLAN encapsulated leading to a partial Denial of Service (DoS). Continued receipted of these specific traffic will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on QFX Series: All versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2. Juniper Networks Junos OS on PTX Series: All versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2.

Improper Handling of Exceptional Conditions in Ethernet interface frame processing of Juniper Networks Junos OS allows an attacker to send specially crafted frames over the local Ethernet segment, causing the interface to go into a down state, resulting in a Denial of Service (DoS) condition. The interface does not recover on its own and the FPC must be reset manually. Continued receipt and processing of these frames will create a sustained Denial of Service (DoS) condition. This issue is platform-specific and affects the following platforms and line cards: * MPC7E/8E/9E and MPC10E on MX240, MX480, MX960, MX2008, MX2010, and MX2020 * MX204, MX10003, MX10008, MX10016 * EX9200, EX9251 * SRX4600 No other products or platforms are affected by this vulnerability. An indication of this issue occurring can be seen in the system log messages, as shown below: user@host> show log messages | match "Failed to complete DFE tuning" fpc4 smic_phy_dfe_tuning_state: et-4/1/6 - Failed to complete DFE tuning (count 3) and interface will be in a permanently down state: user@host> show interfaces et-4/1/6 terse Interface Admin Link Proto Local Remote et-4/1/6 up down et-4/1/6.0 up down aenet --> ae101.0 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S7 on MX Series; 17.1R1 and later versions prior to 17.2R3-S3 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S11, 17.4R3-S1 on MX Series, SRX4600; 18.1 versions prior to 18.1R3-S10 on MX Series, EX9200 Series, SRX4600; 18.2 versions prior to 18.2R3-S3 on MX Series, EX9200 Series, SRX4600; 18.3 versions prior to 18.3R3-S1 on MX Series, EX9200 Series, SRX4600; 18.4 versions prior to 18.4R2-S3, 18.4R3 on MX Series, EX9200 Series, SRX4600; 19.1 versions prior to 19.1R2-S1, 19.1R3 on MX Series, EX9200 Series, SRX4600; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series, EX9200 Series, SRX4600; 19.3 versions prior to 19.3R2 on MX Series, EX9200 Series, SRX4600. This issue does not affect Juniper Networks Junos OS versions prior to 16.1R1.

An Improper Handling of Exceptional Conditions vulnerability in the processing of a transit or directly received malformed IPv6 packet in Juniper Networks Junos OS results in a kernel crash, causing the device to restart, leading to a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects systems with IPv6 configured. Devices with only IPv4 configured are not vulnerable to this issue. This issue affects Juniper Networks Junos OS: 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S1, 20.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 19.4R1.

Due to a vulnerability in DDoS protection in Juniper Networks Junos OS and Junos OS Evolved on QFX5K Series switches in a VXLAN configuration, instability might be experienced in the underlay network as a consequence of exceeding the default ddos-protection aggregate threshold. If an attacker on a client device on the overlay network sends a high volume of specific, legitimate traffic in the overlay network, due to an improperly detected DDoS violation, the leaf might not process certain L2 traffic, sent by spines in the underlay network. Continued receipt and processing of the high volume traffic will sustain the Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on QFX5K Series: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R2-S8, 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S2, 20.3R2. Juniper Networks Junos OS Evolved on QFX5220: All versions prior to 20.3R2-EVO.

An Improper Handling of Exceptional Conditions vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based, unauthenticated attacker to send a specific routing update, causing an rpd core due to memory corruption, leading to a Denial of Service (DoS). This issue can only be triggered when the system is configured for CoS-based forwarding (CBF) with a policy map containing a cos-next-hop-map action (see below). This issue affects: Junos OS: * all versions before 20.4R3-S10, * from 21.2 before 21.2R3-S8, * from 21.3 before 21.3R3, * from 21.4 before 21.4R3, * from 22.1 before 22.1R2; Junos OS Evolved: * all versions before 21.2R3-S8-EVO, * from 21.3 before 21.3R3-EVO, * from 21.4 before 21.4R3-EVO, * from 22.1 before 22.1R2-EVO.

An improper handling of exceptional conditions vulnerability exists in the DNS proxy feature of Palo Alto Networks PAN-OS software that enables a meddler-in-the-middle (MITM) to send specifically crafted traffic to the firewall that causes the service to restart unexpectedly. Repeated attempts to send this request result in denial-of-service to all PAN-OS services by restarting the device in maintenance mode. This issue does not impact Panorama appliances and Prisma Access customers. This issue impacts: PAN-OS 8.1 versions earlier than PAN-OS 8.1.22; PAN-OS 9.0 versions earlier than PAN-OS 9.0.16; PAN-OS 9.1 versions earlier than PAN-OS 9.1.13; PAN-OS 10.0 versions earlier than PAN-OS 10.0.10; PAN-OS 10.1 versions earlier than PAN-OS 10.1.5. This issue does not impact PAN-OS 10.2.

An issue was discovered in open5gs v2.6.6. InitialUEMessage, Registration request sent at a specific time can crash AMF due to incorrect error handling of Nudm_UECM_Registration response.

Directus is a real-time API and App dashboard for managing SQL database content. In affected versions any Directus installation that has websockets enabled can be crashed if the websocket server receives an invalid frame. A malicious user could leverage this bug to crash Directus. This issue has been addressed in version 10.6.2. Users are advised to upgrade. Users unable to upgrade should avoid using websockets.

The Apollo Router is a configurable, high-performance graph router written in Rust to run a federated supergraph that uses Apollo Federation 2. Affected versions are subject to a Denial-of-Service (DoS) type vulnerability which causes the Router to panic and terminate when GraphQL Subscriptions are enabled. It can be triggered when **all of the following conditions are met**: 1. Running Apollo Router v1.28.0, v1.28.1 or v1.29.0 ("impacted versions"); **and** 2. The Supergraph schema provided to the Router (either via Apollo Uplink or explicitly via other configuration) **has a `subscription` type** with root-fields defined; **and** 3. The YAML configuration provided to the Router **has subscriptions enabled** (they are _disabled_ by default), either by setting `enabled: true` _or_ by setting a valid `mode` within the `subscriptions` object (as seen in [subscriptions' documentation](https://www.apollographql.com/docs/router/executing-operations/subscription-support/#router-setup)); **and** 4. An [anonymous](https://spec.graphql.org/draft/#sec-Anonymous-Operation-Definitions) (i.e., un-named) `subscription` operation (e.g., `subscription { ... }`) is received by the Router If **all four** of these criteria are met, the impacted versions will panic and terminate. There is no data-privacy risk or sensitive-information exposure aspect to this vulnerability. This is fixed in Apollo Router v1.29.1. Users are advised to upgrade. Updating to v1.29.1 should be a clear and simple upgrade path for those running impacted versions. However, if Subscriptions are **not** necessary for your Graph – but are enabled via configuration — then disabling subscriptions is another option to mitigate the risk.

A CWE-248: Uncaught Exception vulnerability exists IN Modicon M580 all versions prior to V2.80, which could cause a possible denial of service when sending an appropriately timed HTTP request to the controller.