In the Linux kernel, the following vulnerability has been resolved: iommu/amd: Clear DMA ops when switching domain Since commit 08a27c1c3ecf ("iommu: Add support to change default domain of an iommu group") a user can switch a device between IOMMU and direct DMA through sysfs. This doesn't work for AMD IOMMU at the moment because dev->dma_ops is not cleared when switching from a DMA to an identity IOMMU domain. The DMA layer thus attempts to use the dma-iommu ops on an identity domain, causing an oops: # echo 0000:00:05.0 > /sys/sys/bus/pci/drivers/e1000e/unbind # echo identity > /sys/bus/pci/devices/0000:00:05.0/iommu_group/type # echo 0000:00:05.0 > /sys/sys/bus/pci/drivers/e1000e/bind ... BUG: kernel NULL pointer dereference, address: 0000000000000028 ... Call Trace: iommu_dma_alloc e1000e_setup_tx_resources e1000e_open Since iommu_change_dev_def_domain() calls probe_finalize() again, clear the dma_ops there like Vt-d does.

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: coex: check NULL return of kmalloc in btc_fw_set_monreg() kmalloc may fail, return value might be NULL and will cause NULL pointer dereference. Add check NULL return of kmalloc in btc_fw_set_monreg().

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Fix oops due to NULL pointer dereference in brcmf_sdiod_sglist_rw() This patch fixes a NULL pointer dereference bug in brcmfmac that occurs when a high 'sd_sgentry_align' value applies (e.g. 512) and a lot of queued SKBs are sent from the pkt queue. The problem is the number of entries in the pre-allocated sgtable, it is nents = max(rxglom_size, txglom_size) + max(rxglom_size, txglom_size) >> 4 + 1. Given the default [rt]xglom_size=32 it's actually 35 which is too small. Worst case, the pkt queue can end up with 64 SKBs. This occurs when a new SKB is added for each original SKB if tailroom isn't enough to hold tail_pad. At least one sg entry is needed for each SKB. So, eventually the "skb_queue_walk loop" in brcmf_sdiod_sglist_rw may run out of sg entries. This makes sg_next return NULL and this causes the oops. The patch sets nents to max(rxglom_size, txglom_size) * 2 to be able handle the worst-case. Btw. this requires only 64-35=29 * 16 (or 20 if CONFIG_NEED_SG_DMA_LENGTH) = 464 additional bytes of memory.

In the Linux kernel, the following vulnerability has been resolved: net: encx24j600: check error in devm_regmap_init_encx24j600 devm_regmap_init may return error which caused by like out of memory, this will results in null pointer dereference later when reading or writing register: general protection fault in encx24j600_spi_probe KASAN: null-ptr-deref in range [0x0000000000000090-0x0000000000000097] CPU: 0 PID: 286 Comm: spi-encx24j600- Not tainted 5.15.0-rc2-00142-g9978db750e31-dirty #11 9c53a778c1306b1b02359f3c2bbedc0222cba652 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 RIP: 0010:regcache_cache_bypass drivers/base/regmap/regcache.c:540 Code: 54 41 89 f4 55 53 48 89 fb 48 83 ec 08 e8 26 94 a8 fe 48 8d bb a0 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 4a 03 00 00 4c 8d ab b0 00 00 00 48 8b ab a0 00 RSP: 0018:ffffc900010476b8 EFLAGS: 00010207 RAX: dffffc0000000000 RBX: fffffffffffffff4 RCX: 0000000000000000 RDX: 0000000000000012 RSI: ffff888002de0000 RDI: 0000000000000094 RBP: ffff888013c9a000 R08: 0000000000000000 R09: fffffbfff3f9cc6a R10: ffffc900010476e8 R11: fffffbfff3f9cc69 R12: 0000000000000001 R13: 000000000000000a R14: ffff888013c9af54 R15: ffff888013c9ad08 FS: 00007ffa984ab580(0000) GS:ffff88801fe00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055a6384136c8 CR3: 000000003bbe6003 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: encx24j600_spi_probe drivers/net/ethernet/microchip/encx24j600.c:459 spi_probe drivers/spi/spi.c:397 really_probe drivers/base/dd.c:517 __driver_probe_device drivers/base/dd.c:751 driver_probe_device drivers/base/dd.c:782 __device_attach_driver drivers/base/dd.c:899 bus_for_each_drv drivers/base/bus.c:427 __device_attach drivers/base/dd.c:971 bus_probe_device drivers/base/bus.c:487 device_add drivers/base/core.c:3364 __spi_add_device drivers/spi/spi.c:599 spi_add_device drivers/spi/spi.c:641 spi_new_device drivers/spi/spi.c:717 new_device_store+0x18c/0x1f1 [spi_stub 4e02719357f1ff33f5a43d00630982840568e85e] dev_attr_store drivers/base/core.c:2074 sysfs_kf_write fs/sysfs/file.c:139 kernfs_fop_write_iter fs/kernfs/file.c:300 new_sync_write fs/read_write.c:508 (discriminator 4) vfs_write fs/read_write.c:594 ksys_write fs/read_write.c:648 do_syscall_64 arch/x86/entry/common.c:50 entry_SYSCALL_64_after_hwframe arch/x86/entry/entry_64.S:113 Add error check in devm_regmap_init_encx24j600 to avoid this situation.

In the Linux kernel, the following vulnerability has been resolved: wifi: cw1200: Fix potential NULL dereference A recent refactoring was identified by static analysis to cause a potential NULL dereference, fix this!

In gc_data_segment in fs/f2fs/gc.c in the Linux kernel before 5.16.3, special files are not considered, leading to a move_data_page NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: iommu/arm-smmu: Defer probe of clients after smmu device bound Null pointer dereference occurs due to a race between smmu driver probe and client driver probe, when of_dma_configure() for client is called after the iommu_device_register() for smmu driver probe has executed but before the driver_bound() for smmu driver has been called. Following is how the race occurs: T1:Smmu device probe T2: Client device probe really_probe() arm_smmu_device_probe() iommu_device_register() really_probe() platform_dma_configure() of_dma_configure() of_dma_configure_id() of_iommu_configure() iommu_probe_device() iommu_init_device() arm_smmu_probe_device() arm_smmu_get_by_fwnode() driver_find_device_by_fwnode() driver_find_device() next_device() klist_next() /* null ptr assigned to smmu */ /* null ptr dereference while smmu->streamid_mask */ driver_bound() klist_add_tail() When this null smmu pointer is dereferenced later in arm_smmu_probe_device, the device crashes. Fix this by deferring the probe of the client device until the smmu device has bound to the arm smmu driver. [will: Add comment]

In the Linux kernel, the following vulnerability has been resolved: cacheinfo: Allocate memory during CPU hotplug if not done from the primary CPU Commit 5944ce092b97 ("arch_topology: Build cacheinfo from primary CPU") adds functionality that architectures can use to optionally allocate and build cacheinfo early during boot. Commit 6539cffa9495 ("cacheinfo: Add arch specific early level initializer") lets secondary CPUs correct (and reallocate memory) cacheinfo data if needed. If the early build functionality is not used and cacheinfo does not need correction, memory for cacheinfo is never allocated. x86 does not use the early build functionality. Consequently, during the cacheinfo CPU hotplug callback, last_level_cache_is_valid() attempts to dereference a NULL pointer: BUG: kernel NULL pointer dereference, address: 0000000000000100 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not present page PGD 0 P4D 0 Oops: 0000 [#1] PREEPMT SMP NOPTI CPU: 0 PID 19 Comm: cpuhp/0 Not tainted 6.4.0-rc2 #1 RIP: 0010: last_level_cache_is_valid+0x95/0xe0a Allocate memory for cacheinfo during the cacheinfo CPU hotplug callback if not done earlier. Moreover, before determining the validity of the last-level cache info, ensure that it has been allocated. Simply checking for non-zero cache_leaves() is not sufficient, as some architectures (e.g., Intel processors) have non-zero cache_leaves() before allocation. Dereferencing NULL cacheinfo can occur in update_per_cpu_data_slice_size(). This function iterates over all online CPUs. However, a CPU may have come online recently, but its cacheinfo may not have been allocated yet. While here, remove an unnecessary indentation in allocate_cache_info(). [ bp: Massage. ]

Use-after-free vulnerability in fs/crypto/ in the Linux kernel before 4.10.7 allows local users to cause a denial of service (NULL pointer dereference) or possibly gain privileges by revoking keyring keys being used for ext4, f2fs, or ubifs encryption, causing cryptographic transform objects to be freed prematurely.

In Eclipse Mosquitto version from 1.0 to 1.4.15, a Null Dereference vulnerability was found in the Mosquitto library which could lead to crashes for those applications using the library.

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: Fix potential NULL dereference in mtk_crtc_destroy() In mtk_crtc_create(), if the call to mbox_request_channel() fails then we set the "mtk_crtc->cmdq_client.chan" pointer to NULL. In that situation, we do not call cmdq_pkt_create(). During the cleanup, we need to check if the "mtk_crtc->cmdq_client.chan" is NULL first before calling cmdq_pkt_destroy(). Calling cmdq_pkt_destroy() is unnecessary if we didn't call cmdq_pkt_create() and it will result in a NULL pointer dereference.

The handle_invept function in arch/x86/kvm/vmx.c in the Linux kernel 3.12 through 3.15 allows privileged KVM guest OS users to cause a denial of service (NULL pointer dereference and host OS crash) via a single-context INVEPT instruction with a NULL EPT pointer.

In the Linux kernel, the following vulnerability has been resolved: idpf: fix idpf_vc_core_init error path In an event where the platform running the device control plane is rebooted, reset is detected on the driver. It releases all the resources and waits for the reset to complete. Once the reset is done, it tries to build the resources back. At this time if the device control plane is not yet started, then the driver timeouts on the virtchnl message and retries to establish the mailbox again. In the retry flow, mailbox is deinitialized but the mailbox workqueue is still alive and polling for the mailbox message. This results in accessing the released control queue leading to null-ptr-deref. Fix it by unrolling the work queue cancellation and mailbox deinitialization in the reverse order which they got initialized.

In the Linux kernel, the following vulnerability has been resolved: clk: clk-apple-nco: Add NULL check in applnco_probe Add NULL check in applnco_probe, to handle kernel NULL pointer dereference error.

In LibreCAD 2.2.0, a NULL pointer dereference in the HATCH handling of libdxfrw allows an attacker to crash the application using a crafted DXF document.

In the Linux kernel, the following vulnerability has been resolved: KVM: SVM: Use online_vcpus, not created_vcpus, to iterate over vCPUs Use the kvm_for_each_vcpu() helper to iterate over vCPUs when encrypting VMSAs for SEV, which effectively switches to use online_vcpus instead of created_vcpus. This fixes a possible null-pointer dereference as created_vcpus does not guarantee a vCPU exists, since it is updated at the very beginning of KVM_CREATE_VCPU. created_vcpus exists to allow the bulk of vCPU creation to run in parallel, while still correctly restricting the max number of max vCPUs.

In the Linux kernel, the following vulnerability has been resolved: cpufreq: CPPC: Fix possible null-ptr-deref for cppc_get_cpu_cost() cpufreq_cpu_get_raw() may return NULL if the cpu is not in policy->cpus cpu mask and it will cause null pointer dereference, so check NULL for cppc_get_cpu_cost().

In the Linux kernel, the following vulnerability has been resolved: NFSD: Prevent NULL dereference in nfsd4_process_cb_update() @ses is initialized to NULL. If __nfsd4_find_backchannel() finds no available backchannel session, setup_callback_client() will try to dereference @ses and segfault.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix NULL pointer derefernce in hns_roce_map_mr_sg() ib_map_mr_sg() allows ULPs to specify NULL as the sg_offset argument. The driver needs to check whether it is a NULL pointer before dereferencing it.

In the Linux kernel, the following vulnerability has been resolved: phy: realtek: usb: fix NULL deref in rtk_usb3phy_probe In rtk_usb3phy_probe() devm_kzalloc() may return NULL but this returned value is not checked.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix null-ptr-deref in block_touch_buffer tracepoint Patch series "nilfs2: fix null-ptr-deref bugs on block tracepoints". This series fixes null pointer dereference bugs that occur when using nilfs2 and two block-related tracepoints. This patch (of 2): It has been reported that when using "block:block_touch_buffer" tracepoint, touch_buffer() called from __nilfs_get_folio_block() causes a NULL pointer dereference, or a general protection fault when KASAN is enabled. This happens because since the tracepoint was added in touch_buffer(), it references the dev_t member bh->b_bdev->bd_dev regardless of whether the buffer head has a pointer to a block_device structure. In the current implementation, the block_device structure is set after the function returns to the caller. Here, touch_buffer() is used to mark the folio/page that owns the buffer head as accessed, but the common search helper for folio/page used by the caller function was optimized to mark the folio/page as accessed when it was reimplemented a long time ago, eliminating the need to call touch_buffer() here in the first place. So this solves the issue by eliminating the touch_buffer() call itself.

In the Linux kernel, the following vulnerability has been resolved: virtio_pci: Fix admin vq cleanup by using correct info pointer vp_modern_avq_cleanup() and vp_del_vqs() clean up admin vq resources by virtio_pci_vq_info pointer. The info pointer of admin vq is stored in vp_dev->admin_vq.info instead of vp_dev->vqs[]. Using the info pointer from vp_dev->vqs[] for admin vq causes a kernel NULL pointer dereference bug. In vp_modern_avq_cleanup() and vp_del_vqs(), get the info pointer from vp_dev->admin_vq.info for admin vq to clean up the resources. Also make info ptr as argument of vp_del_vq() to be symmetric with vp_setup_vq(). vp_reset calls vp_modern_avq_cleanup, and causes the Call Trace: ================================================================== BUG: kernel NULL pointer dereference, address:0000000000000000 ... CPU: 49 UID: 0 PID: 4439 Comm: modprobe Not tainted 6.11.0-rc5 #1 RIP: 0010:vp_reset+0x57/0x90 [virtio_pci] Call Trace: <TASK> ... ? vp_reset+0x57/0x90 [virtio_pci] ? vp_reset+0x38/0x90 [virtio_pci] virtio_reset_device+0x1d/0x30 remove_vq_common+0x1c/0x1a0 [virtio_net] virtnet_remove+0xa1/0xc0 [virtio_net] virtio_dev_remove+0x46/0xa0 ... virtio_pci_driver_exit+0x14/0x810 [virtio_pci] ==================================================================

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix null deref accessing lag dev It could be the lag dev is null so stop processing the event. In bond_enslave() the active/backup slave being set before setting the upper dev so first event is without an upper dev. After setting the upper dev with bond_master_upper_dev_link() there is a second event and in that event we have an upper dev.

An issue was discovered in the Linux kernel through 6.5.9. During a race with SQ thread exit, an io_uring/fdinfo.c io_uring_show_fdinfo NULL pointer dereference can occur.

NVIDIA GPU Display Driver contains a vulnerability in the kernel mode layer handler where a NULL pointer dereference may lead to denial of service or potential escalation of privileges

In strongSwan before 5.9.5, a malicious responder can send an EAP-Success message too early without actually authenticating the client and (in the case of EAP methods with mutual authentication and EAP-only authentication for IKEv2) even without server authentication.

In the Linux kernel, the following vulnerability has been resolved: KEYS: trusted: dcp: fix NULL dereference in AEAD crypto operation When sealing or unsealing a key blob we currently do not wait for the AEAD cipher operation to finish and simply return after submitting the request. If there is some load on the system we can exit before the cipher operation is done and the buffer we read from/write to is already removed from the stack. This will e.g. result in NULL pointer dereference errors in the DCP driver during blob creation. Fix this by waiting for the AEAD cipher operation to finish before resuming the seal and unseal calls.

In the Linux kernel, the following vulnerability has been resolved: spi: spi-fsl-dspi: Fix crash when not using GPIO chip select Add check for the return value of spi_get_csgpiod() to avoid passing a NULL pointer to gpiod_direction_output(), preventing a crash when GPIO chip select is not used. Fix below crash: [ 4.251960] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 4.260762] Mem abort info: [ 4.263556] ESR = 0x0000000096000004 [ 4.267308] EC = 0x25: DABT (current EL), IL = 32 bits [ 4.272624] SET = 0, FnV = 0 [ 4.275681] EA = 0, S1PTW = 0 [ 4.278822] FSC = 0x04: level 0 translation fault [ 4.283704] Data abort info: [ 4.286583] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [ 4.292074] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 4.297130] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 4.302445] [0000000000000000] user address but active_mm is swapper [ 4.308805] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP [ 4.315072] Modules linked in: [ 4.318124] CPU: 2 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.0-rc4-next-20241023-00008-ga20ec42c5fc1 #359 [ 4.328130] Hardware name: LS1046A QDS Board (DT) [ 4.332832] pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 4.339794] pc : gpiod_direction_output+0x34/0x5c [ 4.344505] lr : gpiod_direction_output+0x18/0x5c [ 4.349208] sp : ffff80008003b8f0 [ 4.352517] x29: ffff80008003b8f0 x28: 0000000000000000 x27: ffffc96bcc7e9068 [ 4.359659] x26: ffffc96bcc6e00b0 x25: ffffc96bcc598398 x24: ffff447400132810 [ 4.366800] x23: 0000000000000000 x22: 0000000011e1a300 x21: 0000000000020002 [ 4.373940] x20: 0000000000000000 x19: 0000000000000000 x18: ffffffffffffffff [ 4.381081] x17: ffff44740016e600 x16: 0000000500000003 x15: 0000000000000007 [ 4.388221] x14: 0000000000989680 x13: 0000000000020000 x12: 000000000000001e [ 4.395362] x11: 0044b82fa09b5a53 x10: 0000000000000019 x9 : 0000000000000008 [ 4.402502] x8 : 0000000000000002 x7 : 0000000000000007 x6 : 0000000000000000 [ 4.409641] x5 : 0000000000000200 x4 : 0000000002000000 x3 : 0000000000000000 [ 4.416781] x2 : 0000000000022202 x1 : 0000000000000000 x0 : 0000000000000000 [ 4.423921] Call trace: [ 4.426362] gpiod_direction_output+0x34/0x5c (P) [ 4.431067] gpiod_direction_output+0x18/0x5c (L) [ 4.435771] dspi_setup+0x220/0x334

In the Linux kernel, the following vulnerability has been resolved: md/raid10: fix null ptr dereference in raid10_size() In raid10_run() if raid10_set_queue_limits() succeed, the return value is set to zero, and if following procedures failed raid10_run() will return zero while mddev->private is still NULL, causing null ptr dereference in raid10_size(). Fix the problem by only overwrite the return value if raid10_set_queue_limits() failed.

In the Linux kernel, the following vulnerability has been resolved: gfs2: fix double destroy_workqueue error When gfs2_fill_super() fails, destroy_workqueue() is called within gfs2_gl_hash_clear(), and the subsequent code path calls destroy_workqueue() on the same work queue again. This issue can be fixed by setting the work queue pointer to NULL after the first destroy_workqueue() call and checking for a NULL pointer before attempting to destroy the work queue again.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check null pointers before used [WHAT & HOW] Poniters, such as dc->clk_mgr, are null checked previously in the same function, so Coverity warns "implies that "dc->clk_mgr" might be null". As a result, these pointers need to be checked when used again. This fixes 10 FORWARD_NULL issues reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: Input: adp5589-keys - fix NULL pointer dereference We register a devm action to call adp5589_clear_config() and then pass the i2c client as argument so that we can call i2c_get_clientdata() in order to get our device object. However, i2c_set_clientdata() is only being set at the end of the probe function which means that we'll get a NULL pointer dereference in case the probe function fails early.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Handle null 'stream_status' in 'planes_changed_for_existing_stream' This commit adds a null check for 'stream_status' in the function 'planes_changed_for_existing_stream'. Previously, the code assumed 'stream_status' could be null, but did not handle the case where it was actually null. This could lead to a null pointer dereference. Reported by smatch: drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:3784 planes_changed_for_existing_stream() error: we previously assumed 'stream_status' could be null (see line 3774)

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Add null check for head_pipe in dcn201_acquire_free_pipe_for_layer This commit addresses a potential null pointer dereference issue in the `dcn201_acquire_free_pipe_for_layer` function. The issue could occur when `head_pipe` is null. The fix adds a check to ensure `head_pipe` is not null before asserting it. If `head_pipe` is null, the function returns NULL to prevent a potential null pointer dereference. Reported by smatch: drivers/gpu/drm/amd/amdgpu/../display/dc/resource/dcn201/dcn201_resource.c:1016 dcn201_acquire_free_pipe_for_layer() error: we previously assumed 'head_pipe' could be null (see line 1010)

In the Linux kernel, the following vulnerability has been resolved: phy: qcom: qmp-usb-legacy: fix NULL-deref on runtime suspend Commit 413db06c05e7 ("phy: qcom-qmp-usb: clean up probe initialisation") removed most users of the platform device driver data from the qcom-qmp-usb driver, but mistakenly also removed the initialisation despite the data still being used in the runtime PM callbacks. This bug was later reproduced when the driver was copied to create the qmp-usb-legacy driver. Restore the driver data initialisation at probe to avoid a NULL-pointer dereference on runtime suspend. Apparently no one uses runtime PM, which currently needs to be enabled manually through sysfs, with these drivers.

In the Linux kernel, the following vulnerability has been resolved: gso: fix udp gso fraglist segmentation after pull from frag_list Detect gso fraglist skbs with corrupted geometry (see below) and pass these to skb_segment instead of skb_segment_list, as the first can segment them correctly. Valid SKB_GSO_FRAGLIST skbs - consist of two or more segments - the head_skb holds the protocol headers plus first gso_size - one or more frag_list skbs hold exactly one segment - all but the last must be gso_size Optional datapath hooks such as NAT and BPF (bpf_skb_pull_data) can modify these skbs, breaking these invariants. In extreme cases they pull all data into skb linear. For UDP, this causes a NULL ptr deref in __udpv4_gso_segment_list_csum at udp_hdr(seg->next)->dest. Detect invalid geometry due to pull, by checking head_skb size. Don't just drop, as this may blackhole a destination. Convert to be able to pass to regular skb_segment.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Add NULL check for clk_mgr and clk_mgr->funcs in dcn30_init_hw This commit addresses a potential null pointer dereference issue in the `dcn30_init_hw` function. The issue could occur when `dc->clk_mgr` or `dc->clk_mgr->funcs` is null. The fix adds a check to ensure `dc->clk_mgr` and `dc->clk_mgr->funcs` is not null before accessing its functions. This prevents a potential null pointer dereference. Reported by smatch: drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn30/dcn30_hwseq.c:789 dcn30_init_hw() error: we previously assumed 'dc->clk_mgr' could be null (see line 628)

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check null pointer before try to access it [why & how] Change the order of the pipe_ctx->plane_state check to ensure that plane_state is not null before accessing it.

In the Linux kernel, the following vulnerability has been resolved: drm: omapdrm: Add missing check for alloc_ordered_workqueue As it may return NULL pointer and cause NULL pointer dereference. Add check for the return value of alloc_ordered_workqueue.

In the Linux kernel, the following vulnerability has been resolved: phy: qcom: qmp-usb: fix NULL-deref on runtime suspend Commit 413db06c05e7 ("phy: qcom-qmp-usb: clean up probe initialisation") removed most users of the platform device driver data, but mistakenly also removed the initialisation despite the data still being used in the runtime PM callbacks. Restore the driver data initialisation at probe to avoid a NULL-pointer dereference on runtime suspend. Apparently no one uses runtime PM, which currently needs to be enabled manually through sysfs, with this driver.

In the Linux kernel, the following vulnerability has been resolved: ASoC: stm32: spdifrx: fix dma channel release in stm32_spdifrx_remove In case of error when requesting ctrl_chan DMA channel, ctrl_chan is not null. So the release of the dma channel leads to the following issue: [ 4.879000] st,stm32-spdifrx 500d0000.audio-controller: dma_request_slave_channel error -19 [ 4.888975] Unable to handle kernel NULL pointer dereference at virtual address 000000000000003d [...] [ 5.096577] Call trace: [ 5.099099] dma_release_channel+0x24/0x100 [ 5.103235] stm32_spdifrx_remove+0x24/0x60 [snd_soc_stm32_spdifrx] [ 5.109494] stm32_spdifrx_probe+0x320/0x4c4 [snd_soc_stm32_spdifrx] To avoid this issue, release channel only if the pointer is valid.

In the Linux kernel, the following vulnerability has been resolved: ext4: update orig_path in ext4_find_extent() In ext4_find_extent(), if the path is not big enough, we free it and set *orig_path to NULL. But after reallocating and successfully initializing the path, we don't update *orig_path, in which case the caller gets a valid path but a NULL ppath, and this may cause a NULL pointer dereference or a path memory leak. For example: ext4_split_extent path = *ppath = 2000 ext4_find_extent if (depth > path[0].p_maxdepth) kfree(path = 2000); *orig_path = path = NULL; path = kcalloc() = 3000 ext4_split_extent_at(*ppath = NULL) path = *ppath; ex = path[depth].p_ext; // NULL pointer dereference! ================================================================== BUG: kernel NULL pointer dereference, address: 0000000000000010 CPU: 6 UID: 0 PID: 576 Comm: fsstress Not tainted 6.11.0-rc2-dirty #847 RIP: 0010:ext4_split_extent_at+0x6d/0x560 Call Trace: <TASK> ext4_split_extent.isra.0+0xcb/0x1b0 ext4_ext_convert_to_initialized+0x168/0x6c0 ext4_ext_handle_unwritten_extents+0x325/0x4d0 ext4_ext_map_blocks+0x520/0xdb0 ext4_map_blocks+0x2b0/0x690 ext4_iomap_begin+0x20e/0x2c0 [...] ================================================================== Therefore, *orig_path is updated when the extent lookup succeeds, so that the caller can safely use path or *ppath.

The ipv4_pktinfo_prepare function in net/ipv4/ip_sockglue.c in the Linux kernel through 4.9.9 allows attackers to cause a denial of service (system crash) via (1) an application that makes crafted system calls or possibly (2) IPv4 traffic with invalid IP options.