In the Linux kernel, the following vulnerability has been resolved: drm/imagination: Fix kernel crash when hard resetting the GPU The GPU hard reset sequence calls pm_runtime_force_suspend() and pm_runtime_force_resume(), which according to their documentation should only be used during system-wide PM transitions to sleep states. The main issue though is that depending on some internal runtime PM state as seen by pm_runtime_force_suspend() (whether the usage count is <= 1), pm_runtime_force_resume() might not resume the device unless needed. If that happens, the runtime PM resume callback pvr_power_device_resume() is not called, the GPU clocks are not re-enabled, and the kernel crashes on the next attempt to access GPU registers as part of the power-on sequence. Replace calls to pm_runtime_force_suspend() and pm_runtime_force_resume() with direct calls to the driver's runtime PM callbacks, pvr_power_device_suspend() and pvr_power_device_resume(), to ensure clocks are re-enabled and avoid the kernel crash.

In the Linux kernel, the following vulnerability has been resolved: s390/entry: Mark IRQ entries to fix stack depot warnings The stack depot filters out everything outside of the top interrupt context as an uninteresting or irrelevant part of the stack traces. This helps with stack trace de-duplication, avoiding an explosion of saved stack traces that share the same IRQ context code path but originate from different randomly interrupted points, eventually exhausting the stack depot. Filtering uses in_irqentry_text() to identify functions within the .irqentry.text and .softirqentry.text sections, which then become the last stack trace entries being saved. While __do_softirq() is placed into the .softirqentry.text section by common code, populating .irqentry.text is architecture-specific. Currently, the .irqentry.text section on s390 is empty, which prevents stack depot filtering and de-duplication and could result in warnings like: Stack depot reached limit capacity WARNING: CPU: 0 PID: 286113 at lib/stackdepot.c:252 depot_alloc_stack+0x39a/0x3c8 with PREEMPT and KASAN enabled. Fix this by moving the IO/EXT interrupt handlers from .kprobes.text into the .irqentry.text section and updating the kprobes blacklist to include the .irqentry.text section. This is done only for asynchronous interrupts and explicitly not for program checks, which are synchronous and where the context beyond the program check is important to preserve. Despite machine checks being somewhat in between, they are extremely rare, and preserving context when possible is also of value. SVCs and Restart Interrupts are not relevant, one being always at the boundary to user space and the other being a one-time thing. IRQ entries filtering is also optionally used in ftrace function graph, where the same logic applies.

In the Linux kernel, the following vulnerability has been resolved: media: i2c: max9286: fix kernel oops when removing module When removing the max9286 module we get a kernel oops: Unable to handle kernel paging request at virtual address 000000aa00000094 Mem abort info: ESR = 0x96000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004 CM = 0, WnR = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=0000000880d85000 [000000aa00000094] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 96000004 [#1] PREEMPT SMP Modules linked in: fsl_jr_uio caam_jr rng_core libdes caamkeyblob_desc caamhash_desc caamalg_desc crypto_engine max9271 authenc crct10dif_ce mxc_jpeg_encdec CPU: 2 PID: 713 Comm: rmmod Tainted: G C 5.15.5-00057-gaebcd29c8ed7-dirty #5 Hardware name: Freescale i.MX8QXP MEK (DT) pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : i2c_mux_del_adapters+0x24/0xf0 lr : max9286_remove+0x28/0xd0 [max9286] sp : ffff800013a9bbf0 x29: ffff800013a9bbf0 x28: ffff00080b6da940 x27: 0000000000000000 x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000000 x23: ffff000801a5b970 x22: ffff0008048b0890 x21: ffff800009297000 x20: ffff0008048b0f70 x19: 000000aa00000064 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000014 x13: 0000000000000000 x12: ffff000802da49e8 x11: ffff000802051918 x10: ffff000802da4920 x9 : ffff000800030098 x8 : 0101010101010101 x7 : 7f7f7f7f7f7f7f7f x6 : fefefeff6364626d x5 : 8080808000000000 x4 : 0000000000000000 x3 : 0000000000000000 x2 : ffffffffffffffff x1 : ffff00080b6da940 x0 : 0000000000000000 Call trace: i2c_mux_del_adapters+0x24/0xf0 max9286_remove+0x28/0xd0 [max9286] i2c_device_remove+0x40/0x110 __device_release_driver+0x188/0x234 driver_detach+0xc4/0x150 bus_remove_driver+0x60/0xe0 driver_unregister+0x34/0x64 i2c_del_driver+0x58/0xa0 max9286_i2c_driver_exit+0x1c/0x490 [max9286] __arm64_sys_delete_module+0x194/0x260 invoke_syscall+0x48/0x114 el0_svc_common.constprop.0+0xd4/0xfc do_el0_svc+0x2c/0x94 el0_svc+0x28/0x80 el0t_64_sync_handler+0xa8/0x130 el0t_64_sync+0x1a0/0x1a4 The Oops happens because the I2C client data does not point to max9286_priv anymore but to v4l2_subdev. The change happened in max9286_init() which calls v4l2_i2c_subdev_init() later on... Besides fixing the max9286_remove() function, remove the call to i2c_set_clientdata() in max9286_probe(), to avoid confusion, and make the necessary changes to max9286_init() so that it doesn't have to use i2c_get_clientdata() in order to fetch the pointer to priv.

In the Linux kernel, the following vulnerability has been resolved: net: fix information leakage in /proc/net/ptype In one net namespace, after creating a packet socket without binding it to a device, users in other net namespaces can observe the new `packet_type` added by this packet socket by reading `/proc/net/ptype` file. This is minor information leakage as packet socket is namespace aware. Add a net pointer in `packet_type` to keep the net namespace of of corresponding packet socket. In `ptype_seq_show`, this net pointer must be checked when it is not NULL.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: change DMA direction while mapping reinjected packets For fragmented packets, ath12k reassembles each fragment as a normal packet and then reinjects it into HW ring. In this case, the DMA direction should be DMA_TO_DEVICE, not DMA_FROM_DEVICE. Otherwise, an invalid payload may be reinjected into the HW and subsequently delivered to the host. Given that arbitrary memory can be allocated to the skb buffer, knowledge about the data contained in the reinjected buffer is lacking. Consequently, there’s a risk of private information being leaked. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1

In the Linux kernel, the following vulnerability has been resolved: vmci: prevent speculation leaks by sanitizing event in event_deliver() Coverity spotted that event_msg is controlled by user-space, event_msg->event_data.event is passed to event_deliver() and used as an index without sanitization. This change ensures that the event index is sanitized to mitigate any possibility of speculative information leaks. This bug was discovered and resolved using Coverity Static Analysis Security Testing (SAST) by Synopsys, Inc. Only compile tested, no access to HW.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: qca: fix info leak when fetching fw build id Add the missing sanity checks and move the 255-byte build-id buffer off the stack to avoid leaking stack data through debugfs in case the build-info reply is malformed.

In the Linux kernel, the following vulnerability has been resolved: arm64/entry: Mask DAIF in cpu_switch_to(), call_on_irq_stack() `cpu_switch_to()` and `call_on_irq_stack()` manipulate SP to change to different stacks along with the Shadow Call Stack if it is enabled. Those two stack changes cannot be done atomically and both functions can be interrupted by SErrors or Debug Exceptions which, though unlikely, is very much broken : if interrupted, we can end up with mismatched stacks and Shadow Call Stack leading to clobbered stacks. In `cpu_switch_to()`, it can happen when SP_EL0 points to the new task, but x18 stills points to the old task's SCS. When the interrupt handler tries to save the task's SCS pointer, it will save the old task SCS pointer (x18) into the new task struct (pointed to by SP_EL0), clobbering it. In `call_on_irq_stack()`, it can happen when switching from the task stack to the IRQ stack and when switching back. In both cases, we can be interrupted when the SCS pointer points to the IRQ SCS, but SP points to the task stack. The nested interrupt handler pushes its return addresses on the IRQ SCS. It then detects that SP points to the task stack, calls `call_on_irq_stack()` and clobbers the task SCS pointer with the IRQ SCS pointer, which it will also use ! This leads to tasks returning to addresses on the wrong SCS, or even on the IRQ SCS, triggering kernel panics via CONFIG_VMAP_STACK or FPAC if enabled. This is possible on a default config, but unlikely. However, when enabling CONFIG_ARM64_PSEUDO_NMI, DAIF is unmasked and instead the GIC is responsible for filtering what interrupts the CPU should receive based on priority. Given the goal of emulating NMIs, pseudo-NMIs can be received by the CPU even in `cpu_switch_to()` and `call_on_irq_stack()`, possibly *very* frequently depending on the system configuration and workload, leading to unpredictable kernel panics. Completely mask DAIF in `cpu_switch_to()` and restore it when returning. Do the same in `call_on_irq_stack()`, but restore and mask around the branch. Mask DAIF even if CONFIG_SHADOW_CALL_STACK is not enabled for consistency of behaviour between all configurations. Introduce and use an assembly macro for saving and masking DAIF, as the existing one saves but only masks IF.

In the Linux kernel, the following vulnerability has been resolved: HID: intel-ish-hid: Fix kernel panic during warm reset During warm reset device->fw_client is set to NULL. If a bus driver is registered after this NULL setting and before new firmware clients are enumerated by ISHTP, kernel panic will result in the function ishtp_cl_bus_match(). This is because of reference to device->fw_client->props.protocol_name. ISH firmware after getting successfully loaded, sends a warm reset notification to remove all clients from the bus and sets device->fw_client to NULL. Until kernel v5.15, all enabled ISHTP kernel module drivers were loaded right after any of the first ISHTP device was registered, regardless of whether it was a matched or an unmatched device. This resulted in all drivers getting registered much before the warm reset notification from ISH. Starting kernel v5.16, this issue got exposed after the change was introduced to load only bus drivers for the respective matching devices. In this scenario, cros_ec_ishtp device and cros_ec_ishtp driver are registered after the warm reset device fw_client NULL setting. cros_ec_ishtp driver_register() triggers the callback to ishtp_cl_bus_match() to match ISHTP driver to the device and causes kernel panic in guid_equal() when dereferencing fw_client NULL pointer to get protocol_name.

In the Linux kernel, the following vulnerability has been resolved: net: use a bounce buffer for copying skb->mark syzbot found arm64 builds would crash in sock_recv_mark() when CONFIG_HARDENED_USERCOPY=y x86 and powerpc are not detecting the issue because they define user_access_begin. This will be handled in a different patch, because a check_object_size() is missing. Only data from skb->cb[] can be copied directly to/from user space, as explained in commit 79a8a642bf05 ("net: Whitelist the skbuff_head_cache "cb" field") syzbot report was: usercopy: Kernel memory exposure attempt detected from SLUB object 'skbuff_head_cache' (offset 168, size 4)! ------------[ cut here ]------------ kernel BUG at mm/usercopy.c:102 ! Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP Modules linked in: CPU: 0 PID: 4410 Comm: syz-executor533 Not tainted 6.2.0-rc7-syzkaller-17907-g2d3827b3f393 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/21/2023 pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : usercopy_abort+0x90/0x94 mm/usercopy.c:90 lr : usercopy_abort+0x90/0x94 mm/usercopy.c:90 sp : ffff80000fb9b9a0 x29: ffff80000fb9b9b0 x28: ffff0000c6073400 x27: 0000000020001a00 x26: 0000000000000014 x25: ffff80000cf52000 x24: fffffc0000000000 x23: 05ffc00000000200 x22: fffffc000324bf80 x21: ffff0000c92fe1a8 x20: 0000000000000001 x19: 0000000000000004 x18: 0000000000000000 x17: 656a626f2042554c x16: ffff0000c6073dd0 x15: ffff80000dbd2118 x14: ffff0000c6073400 x13: 00000000ffffffff x12: ffff0000c6073400 x11: ff808000081bbb4c x10: 0000000000000000 x9 : 7b0572d7cc0ccf00 x8 : 7b0572d7cc0ccf00 x7 : ffff80000bf650d4 x6 : 0000000000000000 x5 : 0000000000000001 x4 : 0000000000000001 x3 : 0000000000000000 x2 : ffff0001fefbff08 x1 : 0000000100000000 x0 : 000000000000006c Call trace: usercopy_abort+0x90/0x94 mm/usercopy.c:90 __check_heap_object+0xa8/0x100 mm/slub.c:4761 check_heap_object mm/usercopy.c:196 [inline] __check_object_size+0x208/0x6b8 mm/usercopy.c:251 check_object_size include/linux/thread_info.h:199 [inline] __copy_to_user include/linux/uaccess.h:115 [inline] put_cmsg+0x408/0x464 net/core/scm.c:238 sock_recv_mark net/socket.c:975 [inline] __sock_recv_cmsgs+0x1fc/0x248 net/socket.c:984 sock_recv_cmsgs include/net/sock.h:2728 [inline] packet_recvmsg+0x2d8/0x678 net/packet/af_packet.c:3482 ____sys_recvmsg+0x110/0x3a0 ___sys_recvmsg net/socket.c:2737 [inline] __sys_recvmsg+0x194/0x210 net/socket.c:2767 __do_sys_recvmsg net/socket.c:2777 [inline] __se_sys_recvmsg net/socket.c:2774 [inline] __arm64_sys_recvmsg+0x2c/0x3c net/socket.c:2774 __invoke_syscall arch/arm64/kernel/syscall.c:38 [inline] invoke_syscall+0x64/0x178 arch/arm64/kernel/syscall.c:52 el0_svc_common+0xbc/0x180 arch/arm64/kernel/syscall.c:142 do_el0_svc+0x48/0x110 arch/arm64/kernel/syscall.c:193 el0_svc+0x58/0x14c arch/arm64/kernel/entry-common.c:637 el0t_64_sync_handler+0x84/0xf0 arch/arm64/kernel/entry-common.c:655 el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:591 Code: 91388800 aa0903e1 f90003e8 94e6d752 (d4210000)

In the Linux kernel, the following vulnerability has been resolved: s390/ptrace: handle setting of fpc register correctly If the content of the floating point control (fpc) register of a traced process is modified with the ptrace interface the new value is tested for validity by temporarily loading it into the fpc register. This may lead to corruption of the fpc register of the tracing process: if an interrupt happens while the value is temporarily loaded into the fpc register, and within interrupt context floating point or vector registers are used, the current fp/vx registers are saved with save_fpu_regs() assuming they belong to user space and will be loaded into fp/vx registers when returning to user space. test_fp_ctl() restores the original user space fpc register value, however it will be discarded, when returning to user space. In result the tracer will incorrectly continue to run with the value that was supposed to be used for the traced process. Fix this by saving fpu register contents with save_fpu_regs() before using test_fp_ctl().

In the Linux kernel, the following vulnerability has been resolved: HID: intel-ish-hid: ipc: Disable and reenable ACPI GPE bit The EHL (Elkhart Lake) based platforms provide a OOB (Out of band) service, which allows to wakup device when the system is in S5 (Soft-Off state). This OOB service can be enabled/disabled from BIOS settings. When enabled, the ISH device gets PME wake capability. To enable PME wakeup, driver also needs to enable ACPI GPE bit. On resume, BIOS will clear the wakeup bit. So driver need to re-enable it in resume function to keep the next wakeup capability. But this BIOS clearing of wakeup bit doesn't decrement internal OS GPE reference count, so this reenabling on every resume will cause reference count to overflow. So first disable and reenable ACPI GPE bit using acpi_disable_gpe().

In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: Fix oob check condition in mwifiex_process_rx_packet Only skip the code path trying to access the rfc1042 headers when the buffer is too small, so the driver can still process packets without rfc1042 headers.

In the Linux kernel, the following vulnerability has been resolved: power: supply: rk817: Fix node refcount leak Dan Carpenter reports that the Smatch static checker warning has found that there is another refcount leak in the probe function. While of_node_put() was added in one of the return paths, it should in fact be added for ALL return paths that return an error and at driver removal time.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix uaf in smb20_oplock_break_ack drop reference after use opinfo.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Fix oob in ntfs_listxattr The length of name cannot exceed the space occupied by ea.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nftables: exthdr: fix 4-byte stack OOB write If priv->len is a multiple of 4, then dst[len / 4] can write past the destination array which leads to stack corruption. This construct is necessary to clean the remainder of the register in case ->len is NOT a multiple of the register size, so make it conditional just like nft_payload.c does. The bug was added in 4.1 cycle and then copied/inherited when tcp/sctp and ip option support was added. Bug reported by Zero Day Initiative project (ZDI-CAN-21950, ZDI-CAN-21951, ZDI-CAN-21961).

In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Fix OOB read If the index provided by the user is bigger than the mask size, we might do an out of bound read.

In the Linux kernel, the following vulnerability has been resolved: x86/alternatives: Disable KASAN in apply_alternatives() Fei has reported that KASAN triggers during apply_alternatives() on a 5-level paging machine: BUG: KASAN: out-of-bounds in rcu_is_watching() Read of size 4 at addr ff110003ee6419a0 by task swapper/0/0 ... __asan_load4() rcu_is_watching() trace_hardirqs_on() text_poke_early() apply_alternatives() ... On machines with 5-level paging, cpu_feature_enabled(X86_FEATURE_LA57) gets patched. It includes KASAN code, where KASAN_SHADOW_START depends on __VIRTUAL_MASK_SHIFT, which is defined with cpu_feature_enabled(). KASAN gets confused when apply_alternatives() patches the KASAN_SHADOW_START users. A test patch that makes KASAN_SHADOW_START static, by replacing __VIRTUAL_MASK_SHIFT with 56, works around the issue. Fix it for real by disabling KASAN while the kernel is patching alternatives. [ mingo: updated the changelog ]

NVIDIA GPU Display Driver for Linux, all versions, contains a vulnerability in the kernel mode layer (nvidia.ko) in which it does not completely honor operating system file system permissions to provide GPU device-level isolation, which may lead to denial of service or information disclosure.

A vulnerability was found in the pfkey_register function in net/key/af_key.c in the Linux kernel. This flaw allows a local, unprivileged user to gain access to kernel memory, leading to a system crash or a leak of internal kernel information.

In the Linux kernel, the following vulnerability has been resolved: ubifs: Fix read out-of-bounds in ubifs_wbuf_write_nolock() Function ubifs_wbuf_write_nolock() may access buf out of bounds in following process: ubifs_wbuf_write_nolock(): aligned_len = ALIGN(len, 8); // Assume len = 4089, aligned_len = 4096 if (aligned_len <= wbuf->avail) ... // Not satisfy if (wbuf->used) { ubifs_leb_write() // Fill some data in avail wbuf len -= wbuf->avail; // len is still not 8-bytes aligned aligned_len -= wbuf->avail; } n = aligned_len >> c->max_write_shift; if (n) { n <<= c->max_write_shift; err = ubifs_leb_write(c, wbuf->lnum, buf + written, wbuf->offs, n); // n > len, read out of bounds less than 8(n-len) bytes } , which can be catched by KASAN: ========================================================= BUG: KASAN: slab-out-of-bounds in ecc_sw_hamming_calculate+0x1dc/0x7d0 Read of size 4 at addr ffff888105594ff8 by task kworker/u8:4/128 Workqueue: writeback wb_workfn (flush-ubifs_0_0) Call Trace: kasan_report.cold+0x81/0x165 nand_write_page_swecc+0xa9/0x160 ubifs_leb_write+0xf2/0x1b0 [ubifs] ubifs_wbuf_write_nolock+0x421/0x12c0 [ubifs] write_head+0xdc/0x1c0 [ubifs] ubifs_jnl_write_inode+0x627/0x960 [ubifs] wb_workfn+0x8af/0xb80 Function ubifs_wbuf_write_nolock() accepts that parameter 'len' is not 8 bytes aligned, the 'len' represents the true length of buf (which is allocated in 'ubifs_jnl_xxx', eg. ubifs_jnl_write_inode), so ubifs_wbuf_write_nolock() must handle the length read from 'buf' carefully to write leb safely. Fetch a reproducer in [Link].

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Fix stack-out-of-bounds memory access from ioapic_write_indirect() KASAN reports the following issue: BUG: KASAN: stack-out-of-bounds in kvm_make_vcpus_request_mask+0x174/0x440 [kvm] Read of size 8 at addr ffffc9001364f638 by task qemu-kvm/4798 CPU: 0 PID: 4798 Comm: qemu-kvm Tainted: G X --------- --- Hardware name: AMD Corporation DAYTONA_X/DAYTONA_X, BIOS RYM0081C 07/13/2020 Call Trace: dump_stack+0xa5/0xe6 print_address_description.constprop.0+0x18/0x130 ? kvm_make_vcpus_request_mask+0x174/0x440 [kvm] __kasan_report.cold+0x7f/0x114 ? kvm_make_vcpus_request_mask+0x174/0x440 [kvm] kasan_report+0x38/0x50 kasan_check_range+0xf5/0x1d0 kvm_make_vcpus_request_mask+0x174/0x440 [kvm] kvm_make_scan_ioapic_request_mask+0x84/0xc0 [kvm] ? kvm_arch_exit+0x110/0x110 [kvm] ? sched_clock+0x5/0x10 ioapic_write_indirect+0x59f/0x9e0 [kvm] ? static_obj+0xc0/0xc0 ? __lock_acquired+0x1d2/0x8c0 ? kvm_ioapic_eoi_inject_work+0x120/0x120 [kvm] The problem appears to be that 'vcpu_bitmap' is allocated as a single long on stack and it should really be KVM_MAX_VCPUS long. We also seem to clear the lower 16 bits of it with bitmap_zero() for no particular reason (my guess would be that 'bitmap' and 'vcpu_bitmap' variables in kvm_bitmap_or_dest_vcpus() caused the confusion: while the later is indeed 16-bit long, the later should accommodate all possible vCPUs).

In the Linux kernel, the following vulnerability has been resolved: vduse: check that offset is within bounds in get_config() This condition checks "len" but it does not check "offset" and that could result in an out of bounds read if "offset > dev->config_size". The problem is that since both variables are unsigned the "dev->config_size - offset" subtraction would result in a very high unsigned value. I think these checks might not be necessary because "len" and "offset" are supposed to already have been validated using the vhost_vdpa_config_validate() function. But I do not know the code perfectly, and I like to be safe.

In the Linux kernel, the following vulnerability has been resolved: ath5k: fix OOB in ath5k_eeprom_read_pcal_info_5111 The bug was found during fuzzing. Stacktrace locates it in ath5k_eeprom_convert_pcal_info_5111. When none of the curve is selected in the loop, idx can go up to AR5K_EEPROM_N_PD_CURVES. The line makes pd out of bound. pd = &chinfo[pier].pd_curves[idx]; There are many OOB writes using pd later in the code. So I added a sanity check for idx. Checks for other loops involving AR5K_EEPROM_N_PD_CURVES are not needed as the loop index is not used outside the loops. The patch is NOT tested with real device. The following is the fuzzing report BUG: KASAN: slab-out-of-bounds in ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] Write of size 1 at addr ffff8880174a4d60 by task modprobe/214 CPU: 0 PID: 214 Comm: modprobe Not tainted 5.6.0 #1 Call Trace: dump_stack+0x76/0xa0 print_address_description.constprop.0+0x16/0x200 ? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] ? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] __kasan_report.cold+0x37/0x7c ? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] kasan_report+0xe/0x20 ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] ? apic_timer_interrupt+0xa/0x20 ? ath5k_eeprom_init_11a_pcal_freq+0xbc0/0xbc0 [ath5k] ? ath5k_pci_eeprom_read+0x228/0x3c0 [ath5k] ath5k_eeprom_init+0x2513/0x6290 [ath5k] ? ath5k_eeprom_init_11a_pcal_freq+0xbc0/0xbc0 [ath5k] ? usleep_range+0xb8/0x100 ? apic_timer_interrupt+0xa/0x20 ? ath5k_eeprom_read_pcal_info_2413+0x2f20/0x2f20 [ath5k] ath5k_hw_init+0xb60/0x1970 [ath5k] ath5k_init_ah+0x6fe/0x2530 [ath5k] ? kasprintf+0xa6/0xe0 ? ath5k_stop+0x140/0x140 [ath5k] ? _dev_notice+0xf6/0xf6 ? apic_timer_interrupt+0xa/0x20 ath5k_pci_probe.cold+0x29a/0x3d6 [ath5k] ? ath5k_pci_eeprom_read+0x3c0/0x3c0 [ath5k] ? mutex_lock+0x89/0xd0 ? ath5k_pci_eeprom_read+0x3c0/0x3c0 [ath5k] local_pci_probe+0xd3/0x160 pci_device_probe+0x23f/0x3e0 ? pci_device_remove+0x280/0x280 ? pci_device_remove+0x280/0x280 really_probe+0x209/0x5d0

In the Linux kernel, the following vulnerability has been resolved: kvm: avoid speculation-based attacks from out-of-range memslot accesses KVM's mechanism for accessing guest memory translates a guest physical address (gpa) to a host virtual address using the right-shifted gpa (also known as gfn) and a struct kvm_memory_slot. The translation is performed in __gfn_to_hva_memslot using the following formula: hva = slot->userspace_addr + (gfn - slot->base_gfn) * PAGE_SIZE It is expected that gfn falls within the boundaries of the guest's physical memory. However, a guest can access invalid physical addresses in such a way that the gfn is invalid. __gfn_to_hva_memslot is called from kvm_vcpu_gfn_to_hva_prot, which first retrieves a memslot through __gfn_to_memslot. While __gfn_to_memslot does check that the gfn falls within the boundaries of the guest's physical memory or not, a CPU can speculate the result of the check and continue execution speculatively using an illegal gfn. The speculation can result in calculating an out-of-bounds hva. If the resulting host virtual address is used to load another guest physical address, this is effectively a Spectre gadget consisting of two consecutive reads, the second of which is data dependent on the first. Right now it's not clear if there are any cases in which this is exploitable. One interesting case was reported by the original author of this patch, and involves visiting guest page tables on x86. Right now these are not vulnerable because the hva read goes through get_user(), which contains an LFENCE speculation barrier. However, there are patches in progress for x86 uaccess.h to mask kernel addresses instead of using LFENCE; once these land, a guest could use speculation to read from the VMM's ring 3 address space. Other architectures such as ARM already use the address masking method, and would be susceptible to this same kind of data-dependent access gadgets. Therefore, this patch proactively protects from these attacks by masking out-of-bounds gfns in __gfn_to_hva_memslot, which blocks speculation of invalid hvas. Sean Christopherson noted that this patch does not cover kvm_read_guest_offset_cached. This however is limited to a few bytes past the end of the cache, and therefore it is unlikely to be useful in the context of building a chain of data dependent accesses.

In the Linux kernel, the following vulnerability has been resolved: i2c: i801: Don't generate an interrupt on bus reset Now that the i2c-i801 driver supports interrupts, setting the KILL bit in a attempt to recover from a timed out transaction triggers an interrupt. Unfortunately, the interrupt handler (i801_isr) is not prepared for this situation and will try to process the interrupt as if it was signaling the end of a successful transaction. In the case of a block transaction, this can result in an out-of-range memory access. This condition was reproduced several times by syzbot: https://syzkaller.appspot.com/bug?extid=ed71512d469895b5b34e https://syzkaller.appspot.com/bug?extid=8c8dedc0ba9e03f6c79e https://syzkaller.appspot.com/bug?extid=c8ff0b6d6c73d81b610e https://syzkaller.appspot.com/bug?extid=33f6c360821c399d69eb https://syzkaller.appspot.com/bug?extid=be15dc0b1933f04b043a https://syzkaller.appspot.com/bug?extid=b4d3fd1dfd53e90afd79 So disable interrupts while trying to reset the bus. Interrupts will be enabled again for the following transaction.

In the Linux kernel, the following vulnerability has been resolved: NFS: fs_context: validate UDP retrans to prevent shift out-of-bounds Fix shift out-of-bounds in xprt_calc_majortimeo(). This is caused by a garbage timeout (retrans) mount option being passed to nfs mount, in this case from syzkaller. If the protocol is XPRT_TRANSPORT_UDP, then 'retrans' is a shift value for a 64-bit long integer, so 'retrans' cannot be >= 64. If it is >= 64, fail the mount and return an error.

In the Linux kernel, the following vulnerability has been resolved: net: dsa: mt7530: fix VLAN traffic leaks PCR_MATRIX field was set to all 1's when VLAN filtering is enabled, but was not reset when it is disabled, which may cause traffic leaks: ip link add br0 type bridge vlan_filtering 1 ip link add br1 type bridge vlan_filtering 1 ip link set swp0 master br0 ip link set swp1 master br1 ip link set br0 type bridge vlan_filtering 0 ip link set br1 type bridge vlan_filtering 0 # traffic in br0 and br1 will start leaking to each other As port_bridge_{add,del} have set up PCR_MATRIX properly, remove the PCR_MATRIX write from mt7530_port_set_vlan_aware.

In the Linux kernel, the following vulnerability has been resolved: net: qrtr: fix OOB Read in qrtr_endpoint_post Syzbot reported slab-out-of-bounds Read in qrtr_endpoint_post. The problem was in wrong _size_ type: if (len != ALIGN(size, 4) + hdrlen) goto err; If size from qrtr_hdr is 4294967293 (0xfffffffd), the result of ALIGN(size, 4) will be 0. In case of len == hdrlen and size == 4294967293 in header this check won't fail and skb_put_data(skb, data + hdrlen, size); will read out of bound from data, which is hdrlen allocated block.

In the Linux kernel, the following vulnerability has been resolved: ipv6: fix another slab-out-of-bounds in fib6_nh_flush_exceptions While running the self-tests on a KASAN enabled kernel, I observed a slab-out-of-bounds splat very similar to the one reported in commit 821bbf79fe46 ("ipv6: Fix KASAN: slab-out-of-bounds Read in fib6_nh_flush_exceptions"). We additionally need to take care of fib6_metrics initialization failure when the caller provides an nh. The fix is similar, explicitly free the route instead of calling fib6_info_release on a half-initialized object.

In the Linux kernel, the following vulnerability has been resolved: kvm: LAPIC: Restore guard to prevent illegal APIC register access Per the SDM, "any access that touches bytes 4 through 15 of an APIC register may cause undefined behavior and must not be executed." Worse, such an access in kvm_lapic_reg_read can result in a leak of kernel stack contents. Prior to commit 01402cf81051 ("kvm: LAPIC: write down valid APIC registers"), such an access was explicitly disallowed. Restore the guard that was removed in that commit.

In the Linux kernel, the following vulnerability has been resolved: sch_cake: Fix out of bounds when parsing TCP options and header The TCP option parser in cake qdisc (cake_get_tcpopt and cake_tcph_may_drop) could read one byte out of bounds. When the length is 1, the execution flow gets into the loop, reads one byte of the opcode, and if the opcode is neither TCPOPT_EOL nor TCPOPT_NOP, it reads one more byte, which exceeds the length of 1. This fix is inspired by commit 9609dad263f8 ("ipv4: tcp_input: fix stack out of bounds when parsing TCP options."). v2 changes: Added doff validation in cake_get_tcphdr to avoid parsing garbage as TCP header. Although it wasn't strictly an out-of-bounds access (memory was allocated), garbage values could be read where CAKE expected the TCP header if doff was smaller than 5.

In the Linux kernel, the following vulnerability has been resolved: scsi: scsi_debug: Fix out-of-bound read in resp_readcap16() The following warning was observed running syzkaller: [ 3813.830724] sg_write: data in/out 65466/242 bytes for SCSI command 0x9e-- guessing data in; [ 3813.830724] program syz-executor not setting count and/or reply_len properly [ 3813.836956] ================================================================== [ 3813.839465] BUG: KASAN: stack-out-of-bounds in sg_copy_buffer+0x157/0x1e0 [ 3813.841773] Read of size 4096 at addr ffff8883cf80f540 by task syz-executor/1549 [ 3813.846612] Call Trace: [ 3813.846995] dump_stack+0x108/0x15f [ 3813.847524] print_address_description+0xa5/0x372 [ 3813.848243] kasan_report.cold+0x236/0x2a8 [ 3813.849439] check_memory_region+0x240/0x270 [ 3813.850094] memcpy+0x30/0x80 [ 3813.850553] sg_copy_buffer+0x157/0x1e0 [ 3813.853032] sg_copy_from_buffer+0x13/0x20 [ 3813.853660] fill_from_dev_buffer+0x135/0x370 [ 3813.854329] resp_readcap16+0x1ac/0x280 [ 3813.856917] schedule_resp+0x41f/0x1630 [ 3813.858203] scsi_debug_queuecommand+0xb32/0x17e0 [ 3813.862699] scsi_dispatch_cmd+0x330/0x950 [ 3813.863329] scsi_request_fn+0xd8e/0x1710 [ 3813.863946] __blk_run_queue+0x10b/0x230 [ 3813.864544] blk_execute_rq_nowait+0x1d8/0x400 [ 3813.865220] sg_common_write.isra.0+0xe61/0x2420 [ 3813.871637] sg_write+0x6c8/0xef0 [ 3813.878853] __vfs_write+0xe4/0x800 [ 3813.883487] vfs_write+0x17b/0x530 [ 3813.884008] ksys_write+0x103/0x270 [ 3813.886268] __x64_sys_write+0x77/0xc0 [ 3813.886841] do_syscall_64+0x106/0x360 [ 3813.887415] entry_SYSCALL_64_after_hwframe+0x44/0xa9 This issue can be reproduced with the following syzkaller log: r0 = openat(0xffffffffffffff9c, &(0x7f0000000040)='./file0\x00', 0x26e1, 0x0) r1 = syz_open_procfs(0xffffffffffffffff, &(0x7f0000000000)='fd/3\x00') open_by_handle_at(r1, &(0x7f00000003c0)=ANY=[@ANYRESHEX], 0x602000) r2 = syz_open_dev$sg(&(0x7f0000000000), 0x0, 0x40782) write$binfmt_aout(r2, &(0x7f0000000340)=ANY=[@ANYBLOB="00000000deff000000000000000000000000000000000000000000000000000047f007af9e107a41ec395f1bded7be24277a1501ff6196a83366f4e6362bc0ff2b247f68a972989b094b2da4fb3607fcf611a22dd04310d28c75039d"], 0x126) In resp_readcap16() we get "int alloc_len" value -1104926854, and then pass the huge arr_len to fill_from_dev_buffer(), but arr is only 32 bytes. This leads to OOB in sg_copy_buffer(). To solve this issue, define alloc_len as u32.

In the Linux kernel, the following vulnerability has been resolved: asix: fix uninit-value in asix_mdio_read() asix_read_cmd() may read less than sizeof(smsr) bytes and in this case smsr will be uninitialized. Fail log: BUG: KMSAN: uninit-value in asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline] BUG: KMSAN: uninit-value in asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline] drivers/net/usb/asix_common.c:497 BUG: KMSAN: uninit-value in asix_mdio_read+0x3c1/0xb00 drivers/net/usb/asix_common.c:497 drivers/net/usb/asix_common.c:497 asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline] asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline] drivers/net/usb/asix_common.c:497 asix_mdio_read+0x3c1/0xb00 drivers/net/usb/asix_common.c:497 drivers/net/usb/asix_common.c:497

In the Linux kernel, the following vulnerability has been resolved: net: validate lwtstate->data before returning from skb_tunnel_info() skb_tunnel_info() returns pointer of lwtstate->data as ip_tunnel_info type without validation. lwtstate->data can have various types such as mpls_iptunnel_encap, etc and these are not compatible. So skb_tunnel_info() should validate before returning that pointer. Splat looks like: BUG: KASAN: slab-out-of-bounds in vxlan_get_route+0x418/0x4b0 [vxlan] Read of size 2 at addr ffff888106ec2698 by task ping/811 CPU: 1 PID: 811 Comm: ping Not tainted 5.13.0+ #1195 Call Trace: dump_stack_lvl+0x56/0x7b print_address_description.constprop.8.cold.13+0x13/0x2ee ? vxlan_get_route+0x418/0x4b0 [vxlan] ? vxlan_get_route+0x418/0x4b0 [vxlan] kasan_report.cold.14+0x83/0xdf ? vxlan_get_route+0x418/0x4b0 [vxlan] vxlan_get_route+0x418/0x4b0 [vxlan] [ ... ] vxlan_xmit_one+0x148b/0x32b0 [vxlan] [ ... ] vxlan_xmit+0x25c5/0x4780 [vxlan] [ ... ] dev_hard_start_xmit+0x1ae/0x6e0 __dev_queue_xmit+0x1f39/0x31a0 [ ... ] neigh_xmit+0x2f9/0x940 mpls_xmit+0x911/0x1600 [mpls_iptunnel] lwtunnel_xmit+0x18f/0x450 ip_finish_output2+0x867/0x2040 [ ... ]

In the Linux kernel, the following vulnerability has been resolved: coresight: tmc-etf: Fix global-out-of-bounds in tmc_update_etf_buffer() commit 6f755e85c332 ("coresight: Add helper for inserting synchronization packets") removed trailing '\0' from barrier_pkt array and updated the call sites like etb_update_buffer() to have proper checks for barrier_pkt size before read but missed updating tmc_update_etf_buffer() which still reads barrier_pkt past the array size resulting in KASAN out-of-bounds bug. Fix this by adding a check for barrier_pkt size before accessing like it is done in etb_update_buffer(). BUG: KASAN: global-out-of-bounds in tmc_update_etf_buffer+0x4b8/0x698 Read of size 4 at addr ffffffd05b7d1030 by task perf/2629 Call trace: dump_backtrace+0x0/0x27c show_stack+0x20/0x2c dump_stack+0x11c/0x188 print_address_description+0x3c/0x4a4 __kasan_report+0x140/0x164 kasan_report+0x10/0x18 __asan_report_load4_noabort+0x1c/0x24 tmc_update_etf_buffer+0x4b8/0x698 etm_event_stop+0x248/0x2d8 etm_event_del+0x20/0x2c event_sched_out+0x214/0x6f0 group_sched_out+0xd0/0x270 ctx_sched_out+0x2ec/0x518 __perf_event_task_sched_out+0x4fc/0xe6c __schedule+0x1094/0x16a0 preempt_schedule_irq+0x88/0x170 arm64_preempt_schedule_irq+0xf0/0x18c el1_irq+0xe8/0x180 perf_event_exec+0x4d8/0x56c setup_new_exec+0x204/0x400 load_elf_binary+0x72c/0x18c0 search_binary_handler+0x13c/0x420 load_script+0x500/0x6c4 search_binary_handler+0x13c/0x420 exec_binprm+0x118/0x654 __do_execve_file+0x77c/0xba4 __arm64_compat_sys_execve+0x98/0xac el0_svc_common+0x1f8/0x5e0 el0_svc_compat_handler+0x84/0xb0 el0_svc_compat+0x10/0x50 The buggy address belongs to the variable: barrier_pkt+0x10/0x40 Memory state around the buggy address: ffffffd05b7d0f00: fa fa fa fa 04 fa fa fa fa fa fa fa 00 00 00 00 ffffffd05b7d0f80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffffffd05b7d1000: 00 00 00 00 00 00 fa fa fa fa fa fa 00 00 00 03 ^ ffffffd05b7d1080: fa fa fa fa 00 02 fa fa fa fa fa fa 03 fa fa fa ffffffd05b7d1100: fa fa fa fa 00 00 00 00 05 fa fa fa fa fa fa fa ==================================================================

In the Linux kernel, the following vulnerability has been resolved: x86/kvm: Disable kvmclock on all CPUs on shutdown Currenly, we disable kvmclock from machine_shutdown() hook and this only happens for boot CPU. We need to disable it for all CPUs to guard against memory corruption e.g. on restore from hibernate. Note, writing '0' to kvmclock MSR doesn't clear memory location, it just prevents hypervisor from updating the location so for the short while after write and while CPU is still alive, the clock remains usable and correct so we don't need to switch to some other clocksource.

In the Linux kernel, the following vulnerability has been resolved: KVM: x86/mmu: Don't advance iterator after restart due to yielding After dropping mmu_lock in the TDP MMU, restart the iterator during tdp_iter_next() and do not advance the iterator. Advancing the iterator results in skipping the top-level SPTE and all its children, which is fatal if any of the skipped SPTEs were not visited before yielding. When zapping all SPTEs, i.e. when min_level == root_level, restarting the iter and then invoking tdp_iter_next() is always fatal if the current gfn has as a valid SPTE, as advancing the iterator results in try_step_side() skipping the current gfn, which wasn't visited before yielding. Sprinkle WARNs on iter->yielded being true in various helpers that are often used in conjunction with yielding, and tag the helper with __must_check to reduce the probabily of improper usage. Failing to zap a top-level SPTE manifests in one of two ways. If a valid SPTE is skipped by both kvm_tdp_mmu_zap_all() and kvm_tdp_mmu_put_root(), the shadow page will be leaked and KVM will WARN accordingly. WARNING: CPU: 1 PID: 3509 at arch/x86/kvm/mmu/tdp_mmu.c:46 [kvm] RIP: 0010:kvm_mmu_uninit_tdp_mmu+0x3e/0x50 [kvm] Call Trace: <TASK> kvm_arch_destroy_vm+0x130/0x1b0 [kvm] kvm_destroy_vm+0x162/0x2a0 [kvm] kvm_vcpu_release+0x34/0x60 [kvm] __fput+0x82/0x240 task_work_run+0x5c/0x90 do_exit+0x364/0xa10 ? futex_unqueue+0x38/0x60 do_group_exit+0x33/0xa0 get_signal+0x155/0x850 arch_do_signal_or_restart+0xed/0x750 exit_to_user_mode_prepare+0xc5/0x120 syscall_exit_to_user_mode+0x1d/0x40 do_syscall_64+0x48/0xc0 entry_SYSCALL_64_after_hwframe+0x44/0xae If kvm_tdp_mmu_zap_all() skips a gfn/SPTE but that SPTE is then zapped by kvm_tdp_mmu_put_root(), KVM triggers a use-after-free in the form of marking a struct page as dirty/accessed after it has been put back on the free list. This directly triggers a WARN due to encountering a page with page_count() == 0, but it can also lead to data corruption and additional errors in the kernel. WARNING: CPU: 7 PID: 1995658 at arch/x86/kvm/../../../virt/kvm/kvm_main.c:171 RIP: 0010:kvm_is_zone_device_pfn.part.0+0x9e/0xd0 [kvm] Call Trace: <TASK> kvm_set_pfn_dirty+0x120/0x1d0 [kvm] __handle_changed_spte+0x92e/0xca0 [kvm] __handle_changed_spte+0x63c/0xca0 [kvm] __handle_changed_spte+0x63c/0xca0 [kvm] __handle_changed_spte+0x63c/0xca0 [kvm] zap_gfn_range+0x549/0x620 [kvm] kvm_tdp_mmu_put_root+0x1b6/0x270 [kvm] mmu_free_root_page+0x219/0x2c0 [kvm] kvm_mmu_free_roots+0x1b4/0x4e0 [kvm] kvm_mmu_unload+0x1c/0xa0 [kvm] kvm_arch_destroy_vm+0x1f2/0x5c0 [kvm] kvm_put_kvm+0x3b1/0x8b0 [kvm] kvm_vcpu_release+0x4e/0x70 [kvm] __fput+0x1f7/0x8c0 task_work_run+0xf8/0x1a0 do_exit+0x97b/0x2230 do_group_exit+0xda/0x2a0 get_signal+0x3be/0x1e50 arch_do_signal_or_restart+0x244/0x17f0 exit_to_user_mode_prepare+0xcb/0x120 syscall_exit_to_user_mode+0x1d/0x40 do_syscall_64+0x4d/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae Note, the underlying bug existed even before commit 1af4a96025b3 ("KVM: x86/mmu: Yield in TDU MMU iter even if no SPTES changed") moved calls to tdp_mmu_iter_cond_resched() to the beginning of loops, as KVM could still incorrectly advance past a top-level entry when yielding on a lower-level entry. But with respect to leaking shadow pages, the bug was introduced by yielding before processing the current gfn. Alternatively, tdp_mmu_iter_cond_resched() could simply fall through, or callers could jump to their "retry" label. The downside of that approach is that tdp_mmu_iter_cond_resched() _must_ be called before anything else in the loop, and there's no easy way to enfornce that requirement. Ideally, KVM would handling the cond_resched() fully within the iterator macro (the code is actually quite clean) and avoid this entire class of bugs, but that is extremely difficult do wh ---truncated---

In the Linux kernel, the following vulnerability has been resolved: media: ngene: Fix out-of-bounds bug in ngene_command_config_free_buf() Fix an 11-year old bug in ngene_command_config_free_buf() while addressing the following warnings caught with -Warray-bounds: arch/alpha/include/asm/string.h:22:16: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds] arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds] The problem is that the original code is trying to copy 6 bytes of data into a one-byte size member _config_ of the wrong structue FW_CONFIGURE_BUFFERS, in a single call to memcpy(). This causes a legitimate compiler warning because memcpy() overruns the length of &com.cmd.ConfigureBuffers.config. It seems that the right structure is FW_CONFIGURE_FREE_BUFFERS, instead, because it contains 6 more members apart from the header _hdr_. Also, the name of the function ngene_command_config_free_buf() suggests that the actual intention is to ConfigureFreeBuffers, instead of ConfigureBuffers (which takes place in the function ngene_command_config_buf(), above). Fix this by enclosing those 6 members of struct FW_CONFIGURE_FREE_BUFFERS into new struct config, and use &com.cmd.ConfigureFreeBuffers.config as the destination address, instead of &com.cmd.ConfigureBuffers.config, when calling memcpy(). This also helps with the ongoing efforts to globally enable -Warray-bounds and get us closer to being able to tighten the FORTIFY_SOURCE routines on memcpy().

In the Linux kernel, the following vulnerability has been resolved: usb: typec: ucsi: Retrieve all the PDOs instead of just the first 4 commit 4dbc6a4ef06d ("usb: typec: ucsi: save power data objects in PD mode") introduced retrieval of the PDOs when connected to a PD-capable source. But only the first 4 PDOs are received since that is the maximum number that can be fetched at a time given the MESSAGE_IN length limitation (16 bytes). However, as per the PD spec a connected source may advertise up to a maximum of 7 PDOs. If such a source is connected it's possible the PPM could have negotiated a power contract with one of the PDOs at index greater than 4, and would be reflected in the request data object's (RDO) object position field. This would result in an out-of-bounds access when the rdo_index() is used to index into the src_pdos array in ucsi_psy_get_voltage_now(). With the help of the UBSAN -fsanitize=array-bounds checker enabled this exact issue is revealed when connecting to a PD source adapter that advertise 5 PDOs and the PPM enters a contract having selected the 5th one. [ 151.545106][ T70] Unexpected kernel BRK exception at EL1 [ 151.545112][ T70] Internal error: BRK handler: f2005512 [#1] PREEMPT SMP ... [ 151.545499][ T70] pc : ucsi_psy_get_prop+0x208/0x20c [ 151.545507][ T70] lr : power_supply_show_property+0xc0/0x328 ... [ 151.545542][ T70] Call trace: [ 151.545544][ T70] ucsi_psy_get_prop+0x208/0x20c [ 151.545546][ T70] power_supply_uevent+0x1a4/0x2f0 [ 151.545550][ T70] dev_uevent+0x200/0x384 [ 151.545555][ T70] kobject_uevent_env+0x1d4/0x7e8 [ 151.545557][ T70] power_supply_changed_work+0x174/0x31c [ 151.545562][ T70] process_one_work+0x244/0x6f0 [ 151.545564][ T70] worker_thread+0x3e0/0xa64 We can resolve this by instead retrieving and storing up to the maximum of 7 PDOs in the con->src_pdos array. This would involve two calls to the GET_PDOS command.

In the Linux kernel, the following vulnerability has been resolved: netfilter: synproxy: Fix out of bounds when parsing TCP options The TCP option parser in synproxy (synproxy_parse_options) could read one byte out of bounds. When the length is 1, the execution flow gets into the loop, reads one byte of the opcode, and if the opcode is neither TCPOPT_EOL nor TCPOPT_NOP, it reads one more byte, which exceeds the length of 1. This fix is inspired by commit 9609dad263f8 ("ipv4: tcp_input: fix stack out of bounds when parsing TCP options."). v2 changes: Added an early return when length < 0 to avoid calling skb_header_pointer with negative length.

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Fix UBSAN shift-out-of-bounds warning If get_num_sdma_queues or get_num_xgmi_sdma_queues is 0, we end up doing a shift operation where the number of bits shifted equals number of bits in the operand. This behaviour is undefined. Set num_sdma_queues or num_xgmi_sdma_queues to ULLONG_MAX, if the count is >= number of bits in the operand. Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1472

In the Linux kernel, the following vulnerability has been resolved: bpf: Add the missing BPF_LINK_TYPE invocation for sockmap There is an out-of-bounds read in bpf_link_show_fdinfo() for the sockmap link fd. Fix it by adding the missing BPF_LINK_TYPE invocation for sockmap link Also add comments for bpf_link_type to prevent missing updates in the future.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Enhance the attribute size check This combines the overflow and boundary check so that all attribute size will be properly examined while enumerating them. [ 169.181521] BUG: KASAN: slab-out-of-bounds in run_unpack+0x2e3/0x570 [ 169.183161] Read of size 1 at addr ffff8880094b6240 by task mount/247 [ 169.184046] [ 169.184925] CPU: 0 PID: 247 Comm: mount Not tainted 6.0.0-rc7+ #3 [ 169.185908] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 169.187066] Call Trace: [ 169.187492] <TASK> [ 169.188049] dump_stack_lvl+0x49/0x63 [ 169.188495] print_report.cold+0xf5/0x689 [ 169.188964] ? run_unpack+0x2e3/0x570 [ 169.189331] kasan_report+0xa7/0x130 [ 169.189714] ? run_unpack+0x2e3/0x570 [ 169.190079] __asan_load1+0x51/0x60 [ 169.190634] run_unpack+0x2e3/0x570 [ 169.191290] ? run_pack+0x840/0x840 [ 169.191569] ? run_lookup_entry+0xb3/0x1f0 [ 169.192443] ? mi_enum_attr+0x20a/0x230 [ 169.192886] run_unpack_ex+0xad/0x3e0 [ 169.193276] ? run_unpack+0x570/0x570 [ 169.193557] ? ni_load_mi+0x80/0x80 [ 169.193889] ? debug_smp_processor_id+0x17/0x20 [ 169.194236] ? mi_init+0x4a/0x70 [ 169.194496] attr_load_runs_vcn+0x166/0x1c0 [ 169.194851] ? attr_data_write_resident+0x250/0x250 [ 169.195188] mi_read+0x133/0x2c0 [ 169.195481] ntfs_iget5+0x277/0x1780 [ 169.196017] ? call_rcu+0x1c7/0x330 [ 169.196392] ? ntfs_get_block_bmap+0x70/0x70 [ 169.196708] ? evict+0x223/0x280 [ 169.197014] ? __kmalloc+0x33/0x540 [ 169.197305] ? wnd_init+0x15b/0x1b0 [ 169.197599] ntfs_fill_super+0x1026/0x1ba0 [ 169.197994] ? put_ntfs+0x1d0/0x1d0 [ 169.198299] ? vsprintf+0x20/0x20 [ 169.198583] ? mutex_unlock+0x81/0xd0 [ 169.198930] ? set_blocksize+0x95/0x150 [ 169.199269] get_tree_bdev+0x232/0x370 [ 169.199750] ? put_ntfs+0x1d0/0x1d0 [ 169.200094] ntfs_fs_get_tree+0x15/0x20 [ 169.200431] vfs_get_tree+0x4c/0x130 [ 169.200714] path_mount+0x654/0xfe0 [ 169.201067] ? putname+0x80/0xa0 [ 169.201358] ? finish_automount+0x2e0/0x2e0 [ 169.201965] ? putname+0x80/0xa0 [ 169.202445] ? kmem_cache_free+0x1c4/0x440 [ 169.203075] ? putname+0x80/0xa0 [ 169.203414] do_mount+0xd6/0xf0 [ 169.203719] ? path_mount+0xfe0/0xfe0 [ 169.203977] ? __kasan_check_write+0x14/0x20 [ 169.204382] __x64_sys_mount+0xca/0x110 [ 169.204711] do_syscall_64+0x3b/0x90 [ 169.205059] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 169.205571] RIP: 0033:0x7f67a80e948a [ 169.206327] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008 [ 169.208296] RSP: 002b:00007ffddf020f58 EFLAGS: 00000202 ORIG_RAX: 00000000000000a5 [ 169.209253] RAX: ffffffffffffffda RBX: 000055e2547a6060 RCX: 00007f67a80e948a [ 169.209777] RDX: 000055e2547a6260 RSI: 000055e2547a62e0 RDI: 000055e2547aeaf0 [ 169.210342] RBP: 0000000000000000 R08: 000055e2547a6280 R09: 0000000000000020 [ 169.210843] R10: 00000000c0ed0000 R11: 0000000000000202 R12: 000055e2547aeaf0 [ 169.211307] R13: 000055e2547a6260 R14: 0000000000000000 R15: 00000000ffffffff [ 169.211913] </TASK> [ 169.212304] [ 169.212680] Allocated by task 0: [ 169.212963] (stack is not available) [ 169.213200] [ 169.213472] The buggy address belongs to the object at ffff8880094b5e00 [ 169.213472] which belongs to the cache UDP of size 1152 [ 169.214095] The buggy address is located 1088 bytes inside of [ 169.214095] 1152-byte region [ffff8880094b5e00, ffff8880094b6280) [ 169.214639] [ 169.215004] The buggy address belongs to the physical page: [ 169.215766] page:000000002e324c8c refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x94b4 [ 169.218412] head:000000002e324c8c order:2 compound_mapcount:0 compound_pincount:0 [ 169.219078] flags: 0xfffffc0010200(slab|head|node=0|zone=1|lastcpupid=0x1fffff) [ 169.220272] raw: 000fffffc0010200 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: netfilter: conntrack: dccp: copy entire header to stack buffer, not just basic one Eric Dumazet says: nf_conntrack_dccp_packet() has an unique: dh = skb_header_pointer(skb, dataoff, sizeof(_dh), &_dh); And nothing more is 'pulled' from the packet, depending on the content. dh->dccph_doff, and/or dh->dccph_x ...) So dccp_ack_seq() is happily reading stuff past the _dh buffer. BUG: KASAN: stack-out-of-bounds in nf_conntrack_dccp_packet+0x1134/0x11c0 Read of size 4 at addr ffff000128f66e0c by task syz-executor.2/29371 [..] Fix this by increasing the stack buffer to also include room for the extra sequence numbers and all the known dccp packet type headers, then pull again after the initial validation of the basic header. While at it, mark packets invalid that lack 48bit sequence bit but where RFC says the type MUST use them. Compile tested only. v2: first skb_header_pointer() now needs to adjust the size to only pull the generic header. (Eric) Heads-up: I intend to remove dccp conntrack support later this year.

In the Linux kernel, the following vulnerability has been resolved: iavf: Fix out-of-bounds when setting channels on remove If we set channels greater during iavf_remove(), and waiting reset done would be timeout, then returned with error but changed num_active_queues directly, that will lead to OOB like the following logs. Because the num_active_queues is greater than tx/rx_rings[] allocated actually. Reproducer: [root@host ~]# cat repro.sh #!/bin/bash pf_dbsf="0000:41:00.0" vf0_dbsf="0000:41:02.0" g_pids=() function do_set_numvf() { echo 2 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs sleep $((RANDOM%3+1)) echo 0 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs sleep $((RANDOM%3+1)) } function do_set_channel() { local nic=$(ls -1 --indicator-style=none /sys/bus/pci/devices/${vf0_dbsf}/net/) [ -z "$nic" ] && { sleep $((RANDOM%3)) ; return 1; } ifconfig $nic 192.168.18.5 netmask 255.255.255.0 ifconfig $nic up ethtool -L $nic combined 1 ethtool -L $nic combined 4 sleep $((RANDOM%3)) } function on_exit() { local pid for pid in "${g_pids[@]}"; do kill -0 "$pid" &>/dev/null && kill "$pid" &>/dev/null done g_pids=() } trap "on_exit; exit" EXIT while :; do do_set_numvf ; done & g_pids+=($!) while :; do do_set_channel ; done & g_pids+=($!) wait Result: [ 3506.152887] iavf 0000:41:02.0: Removing device [ 3510.400799] ================================================================== [ 3510.400820] BUG: KASAN: slab-out-of-bounds in iavf_free_all_tx_resources+0x156/0x160 [iavf] [ 3510.400823] Read of size 8 at addr ffff88b6f9311008 by task repro.sh/55536 [ 3510.400823] [ 3510.400830] CPU: 101 PID: 55536 Comm: repro.sh Kdump: loaded Tainted: G O --------- -t - 4.18.0 #1 [ 3510.400832] Hardware name: Powerleader PR2008AL/H12DSi-N6, BIOS 2.0 04/09/2021 [ 3510.400835] Call Trace: [ 3510.400851] dump_stack+0x71/0xab [ 3510.400860] print_address_description+0x6b/0x290 [ 3510.400865] ? iavf_free_all_tx_resources+0x156/0x160 [iavf] [ 3510.400868] kasan_report+0x14a/0x2b0 [ 3510.400873] iavf_free_all_tx_resources+0x156/0x160 [iavf] [ 3510.400880] iavf_remove+0x2b6/0xc70 [iavf] [ 3510.400884] ? iavf_free_all_rx_resources+0x160/0x160 [iavf] [ 3510.400891] ? wait_woken+0x1d0/0x1d0 [ 3510.400895] ? notifier_call_chain+0xc1/0x130 [ 3510.400903] pci_device_remove+0xa8/0x1f0 [ 3510.400910] device_release_driver_internal+0x1c6/0x460 [ 3510.400916] pci_stop_bus_device+0x101/0x150 [ 3510.400919] pci_stop_and_remove_bus_device+0xe/0x20 [ 3510.400924] pci_iov_remove_virtfn+0x187/0x420 [ 3510.400927] ? pci_iov_add_virtfn+0xe10/0xe10 [ 3510.400929] ? pci_get_subsys+0x90/0x90 [ 3510.400932] sriov_disable+0xed/0x3e0 [ 3510.400936] ? bus_find_device+0x12d/0x1a0 [ 3510.400953] i40e_free_vfs+0x754/0x1210 [i40e] [ 3510.400966] ? i40e_reset_all_vfs+0x880/0x880 [i40e] [ 3510.400968] ? pci_get_device+0x7c/0x90 [ 3510.400970] ? pci_get_subsys+0x90/0x90 [ 3510.400982] ? pci_vfs_assigned.part.7+0x144/0x210 [ 3510.400987] ? __mutex_lock_slowpath+0x10/0x10 [ 3510.400996] i40e_pci_sriov_configure+0x1fa/0x2e0 [i40e] [ 3510.401001] sriov_numvfs_store+0x214/0x290 [ 3510.401005] ? sriov_totalvfs_show+0x30/0x30 [ 3510.401007] ? __mutex_lock_slowpath+0x10/0x10 [ 3510.401011] ? __check_object_size+0x15a/0x350 [ 3510.401018] kernfs_fop_write+0x280/0x3f0 [ 3510.401022] vfs_write+0x145/0x440 [ 3510.401025] ksys_write+0xab/0x160 [ 3510.401028] ? __ia32_sys_read+0xb0/0xb0 [ 3510.401031] ? fput_many+0x1a/0x120 [ 3510.401032] ? filp_close+0xf0/0x130 [ 3510.401038] do_syscall_64+0xa0/0x370 [ 3510.401041] ? page_fault+0x8/0x30 [ 3510.401043] entry_SYSCALL_64_after_hwframe+0x65/0xca [ 3510.401073] RIP: 0033:0x7f3a9bb842c0 [ 3510.401079] Code: 73 01 c3 48 8b 0d d8 cb 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 89 24 2d 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d ---truncated---

In the Linux kernel, the following vulnerability has been resolved: platform/chrome: cros_ec_chardev: fix kernel data leak from ioctl It is possible to peep kernel page's data by providing larger `insize` in struct cros_ec_command[1] when invoking EC host commands. Fix it by using zeroed memory. [1]: https://elixir.bootlin.com/linux/v6.2/source/include/linux/platform_data/cros_ec_proto.h#L74

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: fix potential array out of bounds access Account for IWL_SEC_WEP_KEY_OFFSET when needed while verifying key_len size in iwl_mvm_sec_key_add().

In the Linux kernel, the following vulnerability has been resolved: ring-buffer: Do not attempt to read past "commit" When iterating over the ring buffer while the ring buffer is active, the writer can corrupt the reader. There's barriers to help detect this and handle it, but that code missed the case where the last event was at the very end of the page and has only 4 bytes left. The checks to detect the corruption by the writer to reads needs to see the length of the event. If the length in the first 4 bytes is zero then the length is stored in the second 4 bytes. But if the writer is in the process of updating that code, there's a small window where the length in the first 4 bytes could be zero even though the length is only 4 bytes. That will cause rb_event_length() to read the next 4 bytes which could happen to be off the allocated page. To protect against this, fail immediately if the next event pointer is less than 8 bytes from the end of the commit (last byte of data), as all events must be a minimum of 8 bytes anyway.