In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: pcie: handle randbuf allocation failure The kzalloc() in brcmf_pcie_download_fw_nvram() will return null if the physical memory has run out. As a result, if we use get_random_bytes() to generate random bytes in the randbuf, the null pointer dereference bug will happen. In order to prevent allocation failure, this patch adds a separate function using buffer on kernel stack to generate random bytes in the randbuf, which could prevent the kernel stack from overflow.

In the Linux kernel, the following vulnerability has been resolved: drm: bridge: cdns-mhdp8546: Fix possible null pointer dereference In cdns_mhdp_atomic_enable(), the return value of drm_mode_duplicate() is assigned to mhdp_state->current_mode, and there is a dereference of it in drm_mode_set_name(), which will lead to a NULL pointer dereference on failure of drm_mode_duplicate(). Fix this bug add a check of mhdp_state->current_mode.

In the Linux kernel, the following vulnerability has been resolved: serial: max3100: Update uart_driver_registered on driver removal The removal of the last MAX3100 device triggers the removal of the driver. However, code doesn't update the respective global variable and after insmod — rmmod — insmod cycle the kernel oopses: max3100 spi-PRP0001:01: max3100_probe: adding port 0 BUG: kernel NULL pointer dereference, address: 0000000000000408 ... RIP: 0010:serial_core_register_port+0xa0/0x840 ... max3100_probe+0x1b6/0x280 [max3100] spi_probe+0x8d/0xb0 Update the actual state so next time UART driver will be registered again. Hugo also noticed, that the error path in the probe also affected by having the variable set, and not cleared. Instead of clearing it move the assignment after the successfull uart_register_driver() call.

In the Linux kernel, the following vulnerability has been resolved: libbpf: Prevent null-pointer dereference when prog to load has no BTF In bpf_objec_load_prog(), there's no guarantee that obj->btf is non-NULL when passing it to btf__fd(), and this function does not perform any check before dereferencing its argument (as bpf_object__btf_fd() used to do). As a consequence, we get segmentation fault errors in bpftool (for example) when trying to load programs that come without BTF information. v2: Keep btf__fd() in the fix instead of reverting to bpf_object__btf_fd().

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Check 'folio' pointer for NULL It can be NULL if bmap is called.

In the Linux kernel, the following vulnerability has been resolved: drm/sched: fix null-ptr-deref in init entity The bug can be triggered by sending an amdgpu_cs_wait_ioctl to the AMDGPU DRM driver on any ASICs with valid context. The bug was reported by Joonkyo Jung <joonkyoj@yonsei.ac.kr>. For example the following code: static void Syzkaller2(int fd) { union drm_amdgpu_ctx arg1; union drm_amdgpu_wait_cs arg2; arg1.in.op = AMDGPU_CTX_OP_ALLOC_CTX; ret = drmIoctl(fd, 0x140106442 /* amdgpu_ctx_ioctl */, &arg1); arg2.in.handle = 0x0; arg2.in.timeout = 0x2000000000000; arg2.in.ip_type = AMD_IP_VPE /* 0x9 */; arg2->in.ip_instance = 0x0; arg2.in.ring = 0x0; arg2.in.ctx_id = arg1.out.alloc.ctx_id; drmIoctl(fd, 0xc0206449 /* AMDGPU_WAIT_CS * /, &arg2); } The ioctl AMDGPU_WAIT_CS without previously submitted job could be assumed that the error should be returned, but the following commit 1decbf6bb0b4dc56c9da6c5e57b994ebfc2be3aa modified the logic and allowed to have sched_rq equal to NULL. As a result when there is no job the ioctl AMDGPU_WAIT_CS returns success. The change fixes null-ptr-deref in init entity and the stack below demonstrates the error condition: [ +0.000007] BUG: kernel NULL pointer dereference, address: 0000000000000028 [ +0.007086] #PF: supervisor read access in kernel mode [ +0.005234] #PF: error_code(0x0000) - not-present page [ +0.005232] PGD 0 P4D 0 [ +0.002501] Oops: 0000 [#1] PREEMPT SMP KASAN NOPTI [ +0.005034] CPU: 10 PID: 9229 Comm: amd_basic Tainted: G B W L 6.7.0+ #4 [ +0.007797] Hardware name: ASUS System Product Name/ROG STRIX B550-F GAMING (WI-FI), BIOS 1401 12/03/2020 [ +0.009798] RIP: 0010:drm_sched_entity_init+0x2d3/0x420 [gpu_sched] [ +0.006426] Code: 80 00 00 00 00 00 00 00 e8 1a 81 82 e0 49 89 9c 24 c0 00 00 00 4c 89 ef e8 4a 80 82 e0 49 8b 5d 00 48 8d 7b 28 e8 3d 80 82 e0 <48> 83 7b 28 00 0f 84 28 01 00 00 4d 8d ac 24 98 00 00 00 49 8d 5c [ +0.019094] RSP: 0018:ffffc90014c1fa40 EFLAGS: 00010282 [ +0.005237] RAX: 0000000000000001 RBX: 0000000000000000 RCX: ffffffff8113f3fa [ +0.007326] RDX: fffffbfff0a7889d RSI: 0000000000000008 RDI: ffffffff853c44e0 [ +0.007264] RBP: ffffc90014c1fa80 R08: 0000000000000001 R09: fffffbfff0a7889c [ +0.007266] R10: ffffffff853c44e7 R11: 0000000000000001 R12: ffff8881a719b010 [ +0.007263] R13: ffff88810d412748 R14: 0000000000000002 R15: 0000000000000000 [ +0.007264] FS: 00007ffff7045540(0000) GS:ffff8883cc900000(0000) knlGS:0000000000000000 [ +0.008236] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ +0.005851] CR2: 0000000000000028 CR3: 000000011912e000 CR4: 0000000000350ef0 [ +0.007175] Call Trace: [ +0.002561] <TASK> [ +0.002141] ? show_regs+0x6a/0x80 [ +0.003473] ? __die+0x25/0x70 [ +0.003124] ? page_fault_oops+0x214/0x720 [ +0.004179] ? preempt_count_sub+0x18/0xc0 [ +0.004093] ? __pfx_page_fault_oops+0x10/0x10 [ +0.004590] ? srso_return_thunk+0x5/0x5f [ +0.004000] ? vprintk_default+0x1d/0x30 [ +0.004063] ? srso_return_thunk+0x5/0x5f [ +0.004087] ? vprintk+0x5c/0x90 [ +0.003296] ? drm_sched_entity_init+0x2d3/0x420 [gpu_sched] [ +0.005807] ? srso_return_thunk+0x5/0x5f [ +0.004090] ? _printk+0xb3/0xe0 [ +0.003293] ? __pfx__printk+0x10/0x10 [ +0.003735] ? asm_sysvec_apic_timer_interrupt+0x1b/0x20 [ +0.005482] ? do_user_addr_fault+0x345/0x770 [ +0.004361] ? exc_page_fault+0x64/0xf0 [ +0.003972] ? asm_exc_page_fault+0x27/0x30 [ +0.004271] ? add_taint+0x2a/0xa0 [ +0.003476] ? drm_sched_entity_init+0x2d3/0x420 [gpu_sched] [ +0.005812] amdgpu_ctx_get_entity+0x3f9/0x770 [amdgpu] [ +0.009530] ? finish_task_switch.isra.0+0x129/0x470 [ +0.005068] ? __pfx_amdgpu_ctx_get_entity+0x10/0x10 [amdgpu] [ +0.010063] ? __kasan_check_write+0x14/0x20 [ +0.004356] ? srso_return_thunk+0x5/0x5f [ +0.004001] ? mutex_unlock+0x81/0xd0 [ +0.003802] ? srso_return_thunk+0x5/0x5f [ +0.004096] amdgpu_cs_wait_ioctl+0xf6/0x270 [amdgpu] [ +0.009355] ? __pfx_ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: fpga: bridge: add owner module and take its refcount The current implementation of the fpga bridge assumes that the low-level module registers a driver for the parent device and uses its owner pointer to take the module's refcount. This approach is problematic since it can lead to a null pointer dereference while attempting to get the bridge if the parent device does not have a driver. To address this problem, add a module owner pointer to the fpga_bridge struct and use it to take the module's refcount. Modify the function for registering a bridge to take an additional owner module parameter and rename it to avoid conflicts. Use the old function name for a helper macro that automatically sets the module that registers the bridge as the owner. This ensures compatibility with existing low-level control modules and reduces the chances of registering a bridge without setting the owner. Also, update the documentation to keep it consistent with the new interface for registering an fpga bridge. Other changes: opportunistically move put_device() from __fpga_bridge_get() to fpga_bridge_get() and of_fpga_bridge_get() to improve code clarity since the bridge device is taken in these functions.

In the Linux kernel, the following vulnerability has been resolved: tracing/osnoise: Use a cpumask to know what threads are kthreads The start_kthread() and stop_thread() code was not always called with the interface_lock held. This means that the kthread variable could be unexpectedly changed causing the kthread_stop() to be called on it when it should not have been, leading to: while true; do rtla timerlat top -u -q & PID=$!; sleep 5; kill -INT $PID; sleep 0.001; kill -TERM $PID; wait $PID; done Causing the following OOPS: Oops: general protection fault, probably for non-canonical address 0xdffffc0000000002: 0000 [#1] PREEMPT SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017] CPU: 5 UID: 0 PID: 885 Comm: timerlatu/5 Not tainted 6.11.0-rc4-test-00002-gbc754cc76d1b-dirty #125 a533010b71dab205ad2f507188ce8c82203b0254 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:hrtimer_active+0x58/0x300 Code: 48 c1 ee 03 41 54 48 01 d1 48 01 d6 55 53 48 83 ec 20 80 39 00 0f 85 30 02 00 00 49 8b 6f 30 4c 8d 75 10 4c 89 f0 48 c1 e8 03 <0f> b6 3c 10 4c 89 f0 83 e0 07 83 c0 03 40 38 f8 7c 09 40 84 ff 0f RSP: 0018:ffff88811d97f940 EFLAGS: 00010202 RAX: 0000000000000002 RBX: ffff88823c6b5b28 RCX: ffffed10478d6b6b RDX: dffffc0000000000 RSI: ffffed10478d6b6c RDI: ffff88823c6b5b28 RBP: 0000000000000000 R08: ffff88823c6b5b58 R09: ffff88823c6b5b60 R10: ffff88811d97f957 R11: 0000000000000010 R12: 00000000000a801d R13: ffff88810d8b35d8 R14: 0000000000000010 R15: ffff88823c6b5b28 FS: 0000000000000000(0000) GS:ffff88823c680000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000561858ad7258 CR3: 000000007729e001 CR4: 0000000000170ef0 Call Trace: <TASK> ? die_addr+0x40/0xa0 ? exc_general_protection+0x154/0x230 ? asm_exc_general_protection+0x26/0x30 ? hrtimer_active+0x58/0x300 ? __pfx_mutex_lock+0x10/0x10 ? __pfx_locks_remove_file+0x10/0x10 hrtimer_cancel+0x15/0x40 timerlat_fd_release+0x8e/0x1f0 ? security_file_release+0x43/0x80 __fput+0x372/0xb10 task_work_run+0x11e/0x1f0 ? _raw_spin_lock+0x85/0xe0 ? __pfx_task_work_run+0x10/0x10 ? poison_slab_object+0x109/0x170 ? do_exit+0x7a0/0x24b0 do_exit+0x7bd/0x24b0 ? __pfx_migrate_enable+0x10/0x10 ? __pfx_do_exit+0x10/0x10 ? __pfx_read_tsc+0x10/0x10 ? ktime_get+0x64/0x140 ? _raw_spin_lock_irq+0x86/0xe0 do_group_exit+0xb0/0x220 get_signal+0x17ba/0x1b50 ? vfs_read+0x179/0xa40 ? timerlat_fd_read+0x30b/0x9d0 ? __pfx_get_signal+0x10/0x10 ? __pfx_timerlat_fd_read+0x10/0x10 arch_do_signal_or_restart+0x8c/0x570 ? __pfx_arch_do_signal_or_restart+0x10/0x10 ? vfs_read+0x179/0xa40 ? ksys_read+0xfe/0x1d0 ? __pfx_ksys_read+0x10/0x10 syscall_exit_to_user_mode+0xbc/0x130 do_syscall_64+0x74/0x110 ? __pfx___rseq_handle_notify_resume+0x10/0x10 ? __pfx_ksys_read+0x10/0x10 ? fpregs_restore_userregs+0xdb/0x1e0 ? fpregs_restore_userregs+0xdb/0x1e0 ? syscall_exit_to_user_mode+0x116/0x130 ? do_syscall_64+0x74/0x110 ? do_syscall_64+0x74/0x110 ? do_syscall_64+0x74/0x110 entry_SYSCALL_64_after_hwframe+0x71/0x79 RIP: 0033:0x7ff0070eca9c Code: Unable to access opcode bytes at 0x7ff0070eca72. RSP: 002b:00007ff006dff8c0 EFLAGS: 00000246 ORIG_RAX: 0000000000000000 RAX: 0000000000000000 RBX: 0000000000000005 RCX: 00007ff0070eca9c RDX: 0000000000000400 RSI: 00007ff006dff9a0 RDI: 0000000000000003 RBP: 00007ff006dffde0 R08: 0000000000000000 R09: 00007ff000000ba0 R10: 00007ff007004b08 R11: 0000000000000246 R12: 0000000000000003 R13: 00007ff006dff9a0 R14: 0000000000000007 R15: 0000000000000008 </TASK> Modules linked in: snd_hda_intel snd_intel_dspcfg snd_intel_sdw_acpi snd_hda_codec snd_hwdep snd_hda_core ---[ end trace 0000000000000000 ]--- This is because it would mistakenly call kthread_stop() on a user space thread making it "exit" before it actually exits. Since kthread ---truncated---

In the Linux kernel, the following vulnerability has been resolved: usb: typec: tcpm: Check for port partner validity before consuming it typec_register_partner() does not guarantee partner registration to always succeed. In the event of failure, port->partner is set to the error value or NULL. Given that port->partner validity is not checked, this results in the following crash: Unable to handle kernel NULL pointer dereference at virtual address xx pc : run_state_machine+0x1bc8/0x1c08 lr : run_state_machine+0x1b90/0x1c08 .. Call trace: run_state_machine+0x1bc8/0x1c08 tcpm_state_machine_work+0x94/0xe4 kthread_worker_fn+0x118/0x328 kthread+0x1d0/0x23c ret_from_fork+0x10/0x20 To prevent the crash, check for port->partner validity before derefencing it in all the call sites.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Atom Integrated System Info v2_2 for DCN35 New request from KMD/VBIOS in order to support new UMA carveout model. This fixes a null dereference from accessing Ctx->dc_bios->integrated_info while it was NULL. DAL parses through the BIOS and extracts the necessary integrated_info but was missing a case for the new BIOS version 2.3.

In the Linux kernel, the following vulnerability has been resolved: bpf, skmsg: Fix NULL pointer dereference in sk_psock_skb_ingress_enqueue Fix NULL pointer data-races in sk_psock_skb_ingress_enqueue() which syzbot reported [1]. [1] BUG: KCSAN: data-race in sk_psock_drop / sk_psock_skb_ingress_enqueue write to 0xffff88814b3278b8 of 8 bytes by task 10724 on cpu 1: sk_psock_stop_verdict net/core/skmsg.c:1257 [inline] sk_psock_drop+0x13e/0x1f0 net/core/skmsg.c:843 sk_psock_put include/linux/skmsg.h:459 [inline] sock_map_close+0x1a7/0x260 net/core/sock_map.c:1648 unix_release+0x4b/0x80 net/unix/af_unix.c:1048 __sock_release net/socket.c:659 [inline] sock_close+0x68/0x150 net/socket.c:1421 __fput+0x2c1/0x660 fs/file_table.c:422 __fput_sync+0x44/0x60 fs/file_table.c:507 __do_sys_close fs/open.c:1556 [inline] __se_sys_close+0x101/0x1b0 fs/open.c:1541 __x64_sys_close+0x1f/0x30 fs/open.c:1541 do_syscall_64+0xd3/0x1d0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 read to 0xffff88814b3278b8 of 8 bytes by task 10713 on cpu 0: sk_psock_data_ready include/linux/skmsg.h:464 [inline] sk_psock_skb_ingress_enqueue+0x32d/0x390 net/core/skmsg.c:555 sk_psock_skb_ingress_self+0x185/0x1e0 net/core/skmsg.c:606 sk_psock_verdict_apply net/core/skmsg.c:1008 [inline] sk_psock_verdict_recv+0x3e4/0x4a0 net/core/skmsg.c:1202 unix_read_skb net/unix/af_unix.c:2546 [inline] unix_stream_read_skb+0x9e/0xf0 net/unix/af_unix.c:2682 sk_psock_verdict_data_ready+0x77/0x220 net/core/skmsg.c:1223 unix_stream_sendmsg+0x527/0x860 net/unix/af_unix.c:2339 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x140/0x180 net/socket.c:745 ____sys_sendmsg+0x312/0x410 net/socket.c:2584 ___sys_sendmsg net/socket.c:2638 [inline] __sys_sendmsg+0x1e9/0x280 net/socket.c:2667 __do_sys_sendmsg net/socket.c:2676 [inline] __se_sys_sendmsg net/socket.c:2674 [inline] __x64_sys_sendmsg+0x46/0x50 net/socket.c:2674 do_syscall_64+0xd3/0x1d0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 value changed: 0xffffffff83d7feb0 -> 0x0000000000000000 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 10713 Comm: syz-executor.4 Tainted: G W 6.8.0-syzkaller-08951-gfe46a7dd189e #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024 Prior to this, commit 4cd12c6065df ("bpf, sockmap: Fix NULL pointer dereference in sk_psock_verdict_data_ready()") fixed one NULL pointer similarly due to no protection of saved_data_ready. Here is another different caller causing the same issue because of the same reason. So we should protect it with sk_callback_lock read lock because the writer side in the sk_psock_drop() uses "write_lock_bh(&sk->sk_callback_lock);". To avoid errors that could happen in future, I move those two pairs of lock into the sk_psock_data_ready(), which is suggested by John Fastabend.

In the Linux kernel, the following vulnerability has been resolved: tls: fix missing memory barrier in tls_init In tls_init(), a write memory barrier is missing, and store-store reordering may cause NULL dereference in tls_{setsockopt,getsockopt}. CPU0 CPU1 ----- ----- // In tls_init() // In tls_ctx_create() ctx = kzalloc() ctx->sk_proto = READ_ONCE(sk->sk_prot) -(1) // In update_sk_prot() WRITE_ONCE(sk->sk_prot, tls_prots) -(2) // In sock_common_setsockopt() READ_ONCE(sk->sk_prot)->setsockopt() // In tls_{setsockopt,getsockopt}() ctx->sk_proto->setsockopt() -(3) In the above scenario, when (1) and (2) are reordered, (3) can observe the NULL value of ctx->sk_proto, causing NULL dereference. To fix it, we rely on rcu_assign_pointer() which implies the release barrier semantic. By moving rcu_assign_pointer() after ctx->sk_proto is initialized, we can ensure that ctx->sk_proto are visible when changing sk->sk_prot.

In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix kernel crash when 1588 is received on HIP08 devices The HIP08 devices does not register the ptp devices, so the hdev->ptp is NULL, but the hardware can receive 1588 messages, and set the HNS3_RXD_TS_VLD_B bit, so, if match this case, the access of hdev->ptp->flags will cause a kernel crash: [ 5888.946472] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000018 [ 5888.946475] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000018 ... [ 5889.266118] pc : hclge_ptp_get_rx_hwts+0x40/0x170 [hclge] [ 5889.272612] lr : hclge_ptp_get_rx_hwts+0x34/0x170 [hclge] [ 5889.279101] sp : ffff800012c3bc50 [ 5889.283516] x29: ffff800012c3bc50 x28: ffff2040002be040 [ 5889.289927] x27: ffff800009116484 x26: 0000000080007500 [ 5889.296333] x25: 0000000000000000 x24: ffff204001c6f000 [ 5889.302738] x23: ffff204144f53c00 x22: 0000000000000000 [ 5889.309134] x21: 0000000000000000 x20: ffff204004220080 [ 5889.315520] x19: ffff204144f53c00 x18: 0000000000000000 [ 5889.321897] x17: 0000000000000000 x16: 0000000000000000 [ 5889.328263] x15: 0000004000140ec8 x14: 0000000000000000 [ 5889.334617] x13: 0000000000000000 x12: 00000000010011df [ 5889.340965] x11: bbfeff4d22000000 x10: 0000000000000000 [ 5889.347303] x9 : ffff800009402124 x8 : 0200f78811dfbb4d [ 5889.353637] x7 : 2200000000191b01 x6 : ffff208002a7d480 [ 5889.359959] x5 : 0000000000000000 x4 : 0000000000000000 [ 5889.366271] x3 : 0000000000000000 x2 : 0000000000000000 [ 5889.372567] x1 : 0000000000000000 x0 : ffff20400095c080 [ 5889.378857] Call trace: [ 5889.382285] hclge_ptp_get_rx_hwts+0x40/0x170 [hclge] [ 5889.388304] hns3_handle_bdinfo+0x324/0x410 [hns3] [ 5889.394055] hns3_handle_rx_bd+0x60/0x150 [hns3] [ 5889.399624] hns3_clean_rx_ring+0x84/0x170 [hns3] [ 5889.405270] hns3_nic_common_poll+0xa8/0x220 [hns3] [ 5889.411084] napi_poll+0xcc/0x264 [ 5889.415329] net_rx_action+0xd4/0x21c [ 5889.419911] __do_softirq+0x130/0x358 [ 5889.424484] irq_exit+0x134/0x154 [ 5889.428700] __handle_domain_irq+0x88/0xf0 [ 5889.433684] gic_handle_irq+0x78/0x2c0 [ 5889.438319] el1_irq+0xb8/0x140 [ 5889.442354] arch_cpu_idle+0x18/0x40 [ 5889.446816] default_idle_call+0x5c/0x1c0 [ 5889.451714] cpuidle_idle_call+0x174/0x1b0 [ 5889.456692] do_idle+0xc8/0x160 [ 5889.460717] cpu_startup_entry+0x30/0xfc [ 5889.465523] secondary_start_kernel+0x158/0x1ec [ 5889.470936] Code: 97ffab78 f9411c14 91408294 f9457284 (f9400c80) [ 5889.477950] SMP: stopping secondary CPUs [ 5890.514626] SMP: failed to stop secondary CPUs 0-69,71-95 [ 5890.522951] Starting crashdump kernel...

In the Linux kernel, the following vulnerability has been resolved: phy: ti: phy-omap-usb2: Fix NULL pointer dereference for SRP If the external phy working together with phy-omap-usb2 does not implement send_srp(), we may still attempt to call it. This can happen on an idle Ethernet gadget triggering a wakeup for example: configfs-gadget.g1 gadget.0: ECM Suspend configfs-gadget.g1 gadget.0: Port suspended. Triggering wakeup ... Unable to handle kernel NULL pointer dereference at virtual address 00000000 when execute ... PC is at 0x0 LR is at musb_gadget_wakeup+0x1d4/0x254 [musb_hdrc] ... musb_gadget_wakeup [musb_hdrc] from usb_gadget_wakeup+0x1c/0x3c [udc_core] usb_gadget_wakeup [udc_core] from eth_start_xmit+0x3b0/0x3d4 [u_ether] eth_start_xmit [u_ether] from dev_hard_start_xmit+0x94/0x24c dev_hard_start_xmit from sch_direct_xmit+0x104/0x2e4 sch_direct_xmit from __dev_queue_xmit+0x334/0xd88 __dev_queue_xmit from arp_solicit+0xf0/0x268 arp_solicit from neigh_probe+0x54/0x7c neigh_probe from __neigh_event_send+0x22c/0x47c __neigh_event_send from neigh_resolve_output+0x14c/0x1c0 neigh_resolve_output from ip_finish_output2+0x1c8/0x628 ip_finish_output2 from ip_send_skb+0x40/0xd8 ip_send_skb from udp_send_skb+0x124/0x340 udp_send_skb from udp_sendmsg+0x780/0x984 udp_sendmsg from __sys_sendto+0xd8/0x158 __sys_sendto from ret_fast_syscall+0x0/0x58 Let's fix the issue by checking for send_srp() and set_vbus() before calling them. For USB peripheral only cases these both could be NULL.

In the Linux kernel, the following vulnerability has been resolved: wifi: nl80211: don't free NULL coalescing rule If the parsing fails, we can dereference a NULL pointer here.

In the Linux kernel, the following vulnerability has been resolved: RDMA/rtrs: Ensure 'ib_sge list' is accessible Move the declaration of the 'ib_sge list' variable outside the 'always_invalidate' block to ensure it remains accessible for use throughout the function. Previously, 'ib_sge list' was declared within the 'always_invalidate' block, limiting its accessibility, then caused a 'BUG: kernel NULL pointer dereference'[1]. ? __die_body.cold+0x19/0x27 ? page_fault_oops+0x15a/0x2d0 ? search_module_extables+0x19/0x60 ? search_bpf_extables+0x5f/0x80 ? exc_page_fault+0x7e/0x180 ? asm_exc_page_fault+0x26/0x30 ? memcpy_orig+0xd5/0x140 rxe_mr_copy+0x1c3/0x200 [rdma_rxe] ? rxe_pool_get_index+0x4b/0x80 [rdma_rxe] copy_data+0xa5/0x230 [rdma_rxe] rxe_requester+0xd9b/0xf70 [rdma_rxe] ? finish_task_switch.isra.0+0x99/0x2e0 rxe_sender+0x13/0x40 [rdma_rxe] do_task+0x68/0x1e0 [rdma_rxe] process_one_work+0x177/0x330 worker_thread+0x252/0x390 ? __pfx_worker_thread+0x10/0x10 This change ensures the variable is available for subsequent operations that require it. [1] https://lore.kernel.org/linux-rdma/6a1f3e8f-deb0-49f9-bc69-a9b03ecfcda7@fujitsu.com/

In the Linux kernel, the following vulnerability has been resolved: fpga: manager: add owner module and take its refcount The current implementation of the fpga manager assumes that the low-level module registers a driver for the parent device and uses its owner pointer to take the module's refcount. This approach is problematic since it can lead to a null pointer dereference while attempting to get the manager if the parent device does not have a driver. To address this problem, add a module owner pointer to the fpga_manager struct and use it to take the module's refcount. Modify the functions for registering the manager to take an additional owner module parameter and rename them to avoid conflicts. Use the old function names for helper macros that automatically set the module that registers the manager as the owner. This ensures compatibility with existing low-level control modules and reduces the chances of registering a manager without setting the owner. Also, update the documentation to keep it consistent with the new interface for registering an fpga manager. Other changes: opportunistically move put_device() from __fpga_mgr_get() to fpga_mgr_get() and of_fpga_mgr_get() to improve code clarity since the manager device is taken in these functions.

In the Linux kernel, the following vulnerability has been resolved: spi: fix null pointer dereference within spi_sync If spi_sync() is called with the non-empty queue and the same spi_message is then reused, the complete callback for the message remains set while the context is cleared, leading to a null pointer dereference when the callback is invoked from spi_finalize_current_message(). With function inlining disabled, the call stack might look like this: _raw_spin_lock_irqsave from complete_with_flags+0x18/0x58 complete_with_flags from spi_complete+0x8/0xc spi_complete from spi_finalize_current_message+0xec/0x184 spi_finalize_current_message from spi_transfer_one_message+0x2a8/0x474 spi_transfer_one_message from __spi_pump_transfer_message+0x104/0x230 __spi_pump_transfer_message from __spi_transfer_message_noqueue+0x30/0xc4 __spi_transfer_message_noqueue from __spi_sync+0x204/0x248 __spi_sync from spi_sync+0x24/0x3c spi_sync from mcp251xfd_regmap_crc_read+0x124/0x28c [mcp251xfd] mcp251xfd_regmap_crc_read [mcp251xfd] from _regmap_raw_read+0xf8/0x154 _regmap_raw_read from _regmap_bus_read+0x44/0x70 _regmap_bus_read from _regmap_read+0x60/0xd8 _regmap_read from regmap_read+0x3c/0x5c regmap_read from mcp251xfd_alloc_can_err_skb+0x1c/0x54 [mcp251xfd] mcp251xfd_alloc_can_err_skb [mcp251xfd] from mcp251xfd_irq+0x194/0xe70 [mcp251xfd] mcp251xfd_irq [mcp251xfd] from irq_thread_fn+0x1c/0x78 irq_thread_fn from irq_thread+0x118/0x1f4 irq_thread from kthread+0xd8/0xf4 kthread from ret_from_fork+0x14/0x28 Fix this by also setting message->complete to NULL when the transfer is complete.

In the Linux kernel, the following vulnerability has been resolved: mm: zswap: fix shrinker NULL crash with cgroup_disable=memory Christian reports a NULL deref in zswap that he bisected down to the zswap shrinker. The issue also cropped up in the bug trackers of libguestfs [1] and the Red Hat bugzilla [2]. The problem is that when memcg is disabled with the boot time flag, the zswap shrinker might get called with sc->memcg == NULL. This is okay in many places, like the lruvec operations. But it crashes in memcg_page_state() - which is only used due to the non-node accounting of cgroup's the zswap memory to begin with. Nhat spotted that the memcg can be NULL in the memcg-disabled case, and I was then able to reproduce the crash locally as well. [1] https://github.com/libguestfs/libguestfs/issues/139 [2] https://bugzilla.redhat.com/show_bug.cgi?id=2275252

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix null deref accessing lag dev It could be the lag dev is null so stop processing the event. In bond_enslave() the active/backup slave being set before setting the upper dev so first event is without an upper dev. After setting the upper dev with bond_master_upper_dev_link() there is a second event and in that event we have an upper dev.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: qca: fix NULL-deref on non-serdev setup Qualcomm ROME controllers can be registered from the Bluetooth line discipline and in this case the HCI UART serdev pointer is NULL. Add the missing sanity check to prevent a NULL-pointer dereference when setup() is called for a non-serdev controller.

In the Linux kernel, the following vulnerability has been resolved: net/rds: fix possible cp null dereference cp might be null, calling cp->cp_conn would produce null dereference [Simon Horman adds:] Analysis: * cp is a parameter of __rds_rdma_map and is not reassigned. * The following call-sites pass a NULL cp argument to __rds_rdma_map() - rds_get_mr() - rds_get_mr_for_dest * Prior to the code above, the following assumes that cp may be NULL (which is indicative, but could itself be unnecessary) trans_private = rs->rs_transport->get_mr( sg, nents, rs, &mr->r_key, cp ? cp->cp_conn : NULL, args->vec.addr, args->vec.bytes, need_odp ? ODP_ZEROBASED : ODP_NOT_NEEDED); * The code modified by this patch is guarded by IS_ERR(trans_private), where trans_private is assigned as per the previous point in this analysis. The only implementation of get_mr that I could locate is rds_ib_get_mr() which can return an ERR_PTR if the conn (4th) argument is NULL. * ret is set to PTR_ERR(trans_private). rds_ib_get_mr can return ERR_PTR(-ENODEV) if the conn (4th) argument is NULL. Thus ret may be -ENODEV in which case the code in question will execute. Conclusion: * cp may be NULL at the point where this patch adds a check; this patch does seem to address a possible bug

In the Linux kernel, the following vulnerability has been resolved: pstore/zone: Add a null pointer check to the psz_kmsg_read kasprintf() returns a pointer to dynamically allocated memory which can be NULL upon failure. Ensure the allocation was successful by checking the pointer validity.

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: fix null pointer access when abort scan During cancel scan we might use vif that weren't scanning. Fix this by using the actual scanning vif.

In the Linux kernel, the following vulnerability has been resolved: sched/eevdf: Prevent vlag from going out of bounds in reweight_eevdf() It was possible to have pick_eevdf() return NULL, which then causes a NULL-deref. This turned out to be due to entity_eligible() returning falsely negative because of a s64 multiplcation overflow. Specifically, reweight_eevdf() computes the vlag without considering the limit placed upon vlag as update_entity_lag() does, and then the scaling multiplication (remember that weight is 20bit fixed point) can overflow. This then leads to the new vruntime being weird which then causes the above entity_eligible() to go side-ways and claim nothing is eligible. Thus limit the range of vlag accordingly. All this was quite rare, but fatal when it does happen.

In the Linux kernel, the following vulnerability has been resolved: drm/arm/malidp: fix a possible null pointer dereference In malidp_mw_connector_reset, new memory is allocated with kzalloc, but no check is performed. In order to prevent null pointer dereferencing, ensure that mw_state is checked before calling __drm_atomic_helper_connector_reset.

In the Linux kernel, the following vulnerability has been resolved: net: phy: micrel: Fix potential null pointer dereference In lan8814_get_sig_rx() and lan8814_get_sig_tx() ptp_parse_header() may return NULL as ptp_header due to abnormal packet type or corrupted packet. Fix this bug by adding ptp_header check. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: erofs: fix inconsistent per-file compression format EROFS can select compression algorithms on a per-file basis, and each per-file compression algorithm needs to be marked in the on-disk superblock for initialization. However, syzkaller can generate inconsistent crafted images that use an unsupported algorithmtype for specific inodes, e.g. use MicroLZMA algorithmtype even it's not set in `sbi->available_compr_algs`. This can lead to an unexpected "BUG: kernel NULL pointer dereference" if the corresponding decompressor isn't built-in. Fix this by checking against `sbi->available_compr_algs` for each m_algorithmformat request. Incorrect !erofs_sb_has_compr_cfgs preset bitmap is now fixed together since it was harmless previously.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check null pointers before used [WHAT & HOW] Poniters, such as dc->clk_mgr, are null checked previously in the same function, so Coverity warns "implies that "dc->clk_mgr" might be null". As a result, these pointers need to be checked when used again. This fixes 10 FORWARD_NULL issues reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: qca: fix NULL-deref on non-serdev suspend Qualcomm ROME controllers can be registered from the Bluetooth line discipline and in this case the HCI UART serdev pointer is NULL. Add the missing sanity check to prevent a NULL-pointer dereference when wakeup() is called for a non-serdev controller during suspend. Just return true for now to restore the original behaviour and address the crash with pre-6.2 kernels, which do not have commit e9b3e5b8c657 ("Bluetooth: hci_qca: only assign wakeup with serial port support") that causes the crash to happen already at setup() time.

In the Linux kernel, the following vulnerability has been resolved: md: fix deadlock between mddev_suspend and flush bio Deadlock occurs when mddev is being suspended while some flush bio is in progress. It is a complex issue. T1. the first flush is at the ending stage, it clears 'mddev->flush_bio' and tries to submit data, but is blocked because mddev is suspended by T4. T2. the second flush sets 'mddev->flush_bio', and attempts to queue md_submit_flush_data(), which is already running (T1) and won't execute again if on the same CPU as T1. T3. the third flush inc active_io and tries to flush, but is blocked because 'mddev->flush_bio' is not NULL (set by T2). T4. mddev_suspend() is called and waits for active_io dec to 0 which is inc by T3. T1 T2 T3 T4 (flush 1) (flush 2) (third 3) (suspend) md_submit_flush_data mddev->flush_bio = NULL; . . md_flush_request . mddev->flush_bio = bio . queue submit_flushes . . . . md_handle_request . . active_io + 1 . . md_flush_request . . wait !mddev->flush_bio . . . . mddev_suspend . . wait !active_io . . . submit_flushes . queue_work md_submit_flush_data . //md_submit_flush_data is already running (T1) . md_handle_request wait resume The root issue is non-atomic inc/dec of active_io during flush process. active_io is dec before md_submit_flush_data is queued, and inc soon after md_submit_flush_data() run. md_flush_request active_io + 1 submit_flushes active_io - 1 md_submit_flush_data md_handle_request active_io + 1 make_request active_io - 1 If active_io is dec after md_handle_request() instead of within submit_flushes(), make_request() can be called directly intead of md_handle_request() in md_submit_flush_data(), and active_io will only inc and dec once in the whole flush process. Deadlock will be fixed. Additionally, the only difference between fixing the issue and before is that there is no return error handling of make_request(). But after previous patch cleaned md_write_start(), make_requst() only return error in raid5_make_request() by dm-raid, see commit 41425f96d7aa ("dm-raid456, md/raid456: fix a deadlock for dm-raid456 while io concurrent with reshape)". Since dm always splits data and flush operation into two separate io, io size of flush submitted by dm always is 0, make_request() will not be called in md_submit_flush_data(). To prevent future modifications from introducing issues, add WARN_ON to ensure make_request() no error is returned in this context.

In the Linux kernel, the following vulnerability has been resolved: fpga: region: add owner module and take its refcount The current implementation of the fpga region assumes that the low-level module registers a driver for the parent device and uses its owner pointer to take the module's refcount. This approach is problematic since it can lead to a null pointer dereference while attempting to get the region during programming if the parent device does not have a driver. To address this problem, add a module owner pointer to the fpga_region struct and use it to take the module's refcount. Modify the functions for registering a region to take an additional owner module parameter and rename them to avoid conflicts. Use the old function names for helper macros that automatically set the module that registers the region as the owner. This ensures compatibility with existing low-level control modules and reduces the chances of registering a region without setting the owner. Also, update the documentation to keep it consistent with the new interface for registering an fpga region.

In the Linux kernel, the following vulnerability has been resolved: media: vidtv: Fix a null-ptr-deref in vidtv_mux_stop_thread syzbot report a null-ptr-deref in vidtv_mux_stop_thread. [1] If dvb->mux is not initialized successfully by vidtv_mux_init() in the vidtv_start_streaming(), it will trigger null pointer dereference about mux in vidtv_mux_stop_thread(). Adjust the timing of streaming initialization and check it before stopping it. [1] KASAN: null-ptr-deref in range [0x0000000000000128-0x000000000000012f] CPU: 0 UID: 0 PID: 5842 Comm: syz-executor248 Not tainted 6.13.0-rc4-syzkaller-00012-g9b2ffa6148b1 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 RIP: 0010:vidtv_mux_stop_thread+0x26/0x80 drivers/media/test-drivers/vidtv/vidtv_mux.c:471 Code: 90 90 90 90 66 0f 1f 00 55 53 48 89 fb e8 82 2e c8 f9 48 8d bb 28 01 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 04 02 84 c0 74 02 7e 3b 0f b6 ab 28 01 00 00 31 ff 89 ee e8 RSP: 0018:ffffc90003f2faa8 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffffff87cfb125 RDX: 0000000000000025 RSI: ffffffff87d120ce RDI: 0000000000000128 RBP: ffff888029b8d220 R08: 0000000000000005 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000003 R12: ffff888029b8d188 R13: ffffffff8f590aa0 R14: ffffc9000581c5c8 R15: ffff888029a17710 FS: 00007f7eef5156c0(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7eef5e635c CR3: 0000000076ca6000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> vidtv_stop_streaming drivers/media/test-drivers/vidtv/vidtv_bridge.c:209 [inline] vidtv_stop_feed+0x151/0x250 drivers/media/test-drivers/vidtv/vidtv_bridge.c:252 dmx_section_feed_stop_filtering+0x90/0x160 drivers/media/dvb-core/dvb_demux.c:1000 dvb_dmxdev_feed_stop.isra.0+0x1ee/0x270 drivers/media/dvb-core/dmxdev.c:486 dvb_dmxdev_filter_stop+0x22a/0x3a0 drivers/media/dvb-core/dmxdev.c:559 dvb_dmxdev_filter_free drivers/media/dvb-core/dmxdev.c:840 [inline] dvb_demux_release+0x92/0x550 drivers/media/dvb-core/dmxdev.c:1246 __fput+0x3f8/0xb60 fs/file_table.c:450 task_work_run+0x14e/0x250 kernel/task_work.c:239 get_signal+0x1d3/0x2610 kernel/signal.c:2790 arch_do_signal_or_restart+0x90/0x7e0 arch/x86/kernel/signal.c:337 exit_to_user_mode_loop kernel/entry/common.c:111 [inline] exit_to_user_mode_prepare include/linux/entry-common.h:329 [inline] __syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline] syscall_exit_to_user_mode+0x150/0x2a0 kernel/entry/common.c:218 do_syscall_64+0xda/0x250 arch/x86/entry/common.c:89 entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: media: imx-jpeg: Fix potential error pointer dereference in detach_pm() The proble is on the first line: if (jpeg->pd_dev[i] && !pm_runtime_suspended(jpeg->pd_dev[i])) If jpeg->pd_dev[i] is an error pointer, then passing it to pm_runtime_suspended() will lead to an Oops. The other conditions check for both error pointers and NULL, but it would be more clear to use the IS_ERR_OR_NULL() check for that.

In the Linux kernel, the following vulnerability has been resolved: usb: xhci: Fix NULL pointer dereference on certain command aborts If a command is queued to the final usable TRB of a ring segment, the enqueue pointer is advanced to the subsequent link TRB and no further. If the command is later aborted, when the abort completion is handled the dequeue pointer is advanced to the first TRB of the next segment. If no further commands are queued, xhci_handle_stopped_cmd_ring() sees the ring pointers unequal and assumes that there is a pending command, so it calls xhci_mod_cmd_timer() which crashes if cur_cmd was NULL. Don't attempt timer setup if cur_cmd is NULL. The subsequent doorbell ring likely is unnecessary too, but it's harmless. Leave it alone. This is probably Bug 219532, but no confirmation has been received. The issue has been independently reproduced and confirmed fixed using a USB MCU programmed to NAK the Status stage of SET_ADDRESS forever. Everything continued working normally after several prevented crashes.

In the Linux kernel, the following vulnerability has been resolved: ACPI: x86: Add adev NULL check to acpi_quirk_skip_serdev_enumeration() acpi_dev_hid_match() does not check for adev == NULL, dereferencing it unconditional. Add a check for adev being NULL before calling acpi_dev_hid_match(). At the moment acpi_quirk_skip_serdev_enumeration() is never called with a controller_parent without an ACPI companion, but better safe than sorry.

In the Linux kernel, the following vulnerability has been resolved: OPP: fix dev_pm_opp_find_bw_*() when bandwidth table not initialized If a driver calls dev_pm_opp_find_bw_ceil/floor() the retrieve bandwidth from the OPP table but the bandwidth table was not created because the interconnect properties were missing in the OPP consumer node, the kernel will crash with: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004 ... pc : _read_bw+0x8/0x10 lr : _opp_table_find_key+0x9c/0x174 ... Call trace: _read_bw+0x8/0x10 (P) _opp_table_find_key+0x9c/0x174 (L) _find_key+0x98/0x168 dev_pm_opp_find_bw_ceil+0x50/0x88 ... In order to fix the crash, create an assert function to check if the bandwidth table was created before trying to get a bandwidth with _read_bw().

In the Linux kernel, the following vulnerability has been resolved: ata: libata-core: Fix null pointer dereference on error If the ata_port_alloc() call in ata_host_alloc() fails, ata_host_release() will get called. However, the code in ata_host_release() tries to free ata_port struct members unconditionally, which can lead to the following: BUG: unable to handle page fault for address: 0000000000003990 PGD 0 P4D 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 10 PID: 594 Comm: (udev-worker) Not tainted 6.10.0-rc5 #44 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:ata_host_release.cold+0x2f/0x6e [libata] Code: e4 4d 63 f4 44 89 e2 48 c7 c6 90 ad 32 c0 48 c7 c7 d0 70 33 c0 49 83 c6 0e 41 RSP: 0018:ffffc90000ebb968 EFLAGS: 00010246 RAX: 0000000000000041 RBX: ffff88810fb52e78 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff88813b3218c0 RDI: ffff88813b3218c0 RBP: ffff88810fb52e40 R08: 0000000000000000 R09: 6c65725f74736f68 R10: ffffc90000ebb738 R11: 73692033203a746e R12: 0000000000000004 R13: 0000000000000000 R14: 0000000000000011 R15: 0000000000000006 FS: 00007f6cc55b9980(0000) GS:ffff88813b300000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000003990 CR3: 00000001122a2000 CR4: 0000000000750ef0 PKRU: 55555554 Call Trace: <TASK> ? __die_body.cold+0x19/0x27 ? page_fault_oops+0x15a/0x2f0 ? exc_page_fault+0x7e/0x180 ? asm_exc_page_fault+0x26/0x30 ? ata_host_release.cold+0x2f/0x6e [libata] ? ata_host_release.cold+0x2f/0x6e [libata] release_nodes+0x35/0xb0 devres_release_group+0x113/0x140 ata_host_alloc+0xed/0x120 [libata] ata_host_alloc_pinfo+0x14/0xa0 [libata] ahci_init_one+0x6c9/0xd20 [ahci] Do not access ata_port struct members unconditionally.

In the Linux kernel, the following vulnerability has been resolved: clk: mmp2: call pm_genpd_init() only after genpd.name is set Setting the genpd's struct device's name with dev_set_name() is happening within pm_genpd_init(). If it remains NULL, things can blow up later, such as when crafting the devfs hierarchy for the power domain: Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read ... Call trace: strlen from start_creating+0x90/0x138 start_creating from debugfs_create_dir+0x20/0x178 debugfs_create_dir from genpd_debug_add.part.0+0x4c/0x144 genpd_debug_add.part.0 from genpd_debug_init+0x74/0x90 genpd_debug_init from do_one_initcall+0x5c/0x244 do_one_initcall from kernel_init_freeable+0x19c/0x1f4 kernel_init_freeable from kernel_init+0x1c/0x12c kernel_init from ret_from_fork+0x14/0x28 Bisecting tracks this crash back to commit 899f44531fe6 ("pmdomain: core: Add GENPD_FLAG_DEV_NAME_FW flag"), which exchanges use of genpd->name with dev_name(&genpd->dev) in genpd_debug_add.part().

In the Linux kernel, the following vulnerability has been resolved: ASoC: SOF: Intel: hda-dai: Ensure DAI widget is valid during params Each cpu DAI should associate with a widget. However, the topology might not create the right number of DAI widgets for aggregated amps. And it will cause NULL pointer deference. Check that the DAI widget associated with the CPU DAI is valid to prevent NULL pointer deference due to missing DAI widgets in topologies with aggregated amps.

In the Linux kernel, the following vulnerability has been resolved: nfs: Fix oops in nfs_netfs_init_request() when copying to cache When netfslib wants to copy some data that has just been read on behalf of nfs, it creates a new write request and calls nfs_netfs_init_request() to initialise it, but with a NULL file pointer. This causes nfs_file_open_context() to oops - however, we don't actually need the nfs context as we're only going to write to the cache. Fix this by just returning if we aren't given a file pointer and emit a warning if the request was for something other than copy-to-cache. Further, fix nfs_netfs_free_request() so that it doesn't try to free the context if the pointer is NULL.

In the Linux kernel, the following vulnerability has been resolved: ocfs2: fix NULL pointer dereference in ocfs2_journal_dirty() bdev->bd_super has been removed and commit 8887b94d9322 change the usage from bdev->bd_super to b_assoc_map->host->i_sb. This introduces the following NULL pointer dereference in ocfs2_journal_dirty() since b_assoc_map is still not initialized. This can be easily reproduced by running xfstests generic/186, which simulate no more credits. [ 134.351592] BUG: kernel NULL pointer dereference, address: 0000000000000000 ... [ 134.355341] RIP: 0010:ocfs2_journal_dirty+0x14f/0x160 [ocfs2] ... [ 134.365071] Call Trace: [ 134.365312] <TASK> [ 134.365524] ? __die_body+0x1e/0x60 [ 134.365868] ? page_fault_oops+0x13d/0x4f0 [ 134.366265] ? __pfx_bit_wait_io+0x10/0x10 [ 134.366659] ? schedule+0x27/0xb0 [ 134.366981] ? exc_page_fault+0x6a/0x140 [ 134.367356] ? asm_exc_page_fault+0x26/0x30 [ 134.367762] ? ocfs2_journal_dirty+0x14f/0x160 [ocfs2] [ 134.368305] ? ocfs2_journal_dirty+0x13d/0x160 [ocfs2] [ 134.368837] ocfs2_create_new_meta_bhs.isra.51+0x139/0x2e0 [ocfs2] [ 134.369454] ocfs2_grow_tree+0x688/0x8a0 [ocfs2] [ 134.369927] ocfs2_split_and_insert.isra.67+0x35c/0x4a0 [ocfs2] [ 134.370521] ocfs2_split_extent+0x314/0x4d0 [ocfs2] [ 134.371019] ocfs2_change_extent_flag+0x174/0x410 [ocfs2] [ 134.371566] ocfs2_add_refcount_flag+0x3fa/0x630 [ocfs2] [ 134.372117] ocfs2_reflink_remap_extent+0x21b/0x4c0 [ocfs2] [ 134.372994] ? inode_update_timestamps+0x4a/0x120 [ 134.373692] ? __pfx_ocfs2_journal_access_di+0x10/0x10 [ocfs2] [ 134.374545] ? __pfx_ocfs2_journal_access_di+0x10/0x10 [ocfs2] [ 134.375393] ocfs2_reflink_remap_blocks+0xe4/0x4e0 [ocfs2] [ 134.376197] ocfs2_remap_file_range+0x1de/0x390 [ocfs2] [ 134.376971] ? security_file_permission+0x29/0x50 [ 134.377644] vfs_clone_file_range+0xfe/0x320 [ 134.378268] ioctl_file_clone+0x45/0xa0 [ 134.378853] do_vfs_ioctl+0x457/0x990 [ 134.379422] __x64_sys_ioctl+0x6e/0xd0 [ 134.379987] do_syscall_64+0x5d/0x170 [ 134.380550] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 134.381231] RIP: 0033:0x7fa4926397cb [ 134.381786] Code: 73 01 c3 48 8b 0d bd 56 38 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 8d 56 38 00 f7 d8 64 89 01 48 [ 134.383930] RSP: 002b:00007ffc2b39f7b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 134.384854] RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00007fa4926397cb [ 134.385734] RDX: 00007ffc2b39f7f0 RSI: 000000004020940d RDI: 0000000000000003 [ 134.386606] RBP: 0000000000000000 R08: 00111a82a4f015bb R09: 00007fa494221000 [ 134.387476] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 [ 134.388342] R13: 0000000000f10000 R14: 0000558e844e2ac8 R15: 0000000000f10000 [ 134.389207] </TASK> Fix it by only aborting transaction and journal in ocfs2_journal_dirty() now, and leave ocfs2_abort() later when detecting an aborted handle, e.g. start next transaction. Also log the handle details in this case.

In the Linux kernel, the following vulnerability has been resolved: net: stmmac: fix tc flower deletion for VLAN priority Rx steering To replicate the issue:- 1) Add 1 flower filter for VLAN Priority based frame steering:- $ IFDEVNAME=eth0 $ tc qdisc add dev $IFDEVNAME ingress $ tc qdisc add dev $IFDEVNAME root mqprio num_tc 8 \ map 0 1 2 3 4 5 6 7 0 0 0 0 0 0 0 0 \ queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0 $ tc filter add dev $IFDEVNAME parent ffff: protocol 802.1Q \ flower vlan_prio 0 hw_tc 0 2) Get the 'pref' id $ tc filter show dev $IFDEVNAME ingress 3) Delete a specific tc flower record (say pref 49151) $ tc filter del dev $IFDEVNAME parent ffff: pref 49151 From dmesg, we will observe kernel NULL pointer ooops [ 197.170464] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 197.171367] #PF: supervisor read access in kernel mode [ 197.171367] #PF: error_code(0x0000) - not-present page [ 197.171367] PGD 0 P4D 0 [ 197.171367] Oops: 0000 [#1] PREEMPT SMP NOPTI <snip> [ 197.171367] RIP: 0010:tc_setup_cls+0x20b/0x4a0 [stmmac] <snip> [ 197.171367] Call Trace: [ 197.171367] <TASK> [ 197.171367] ? __stmmac_disable_all_queues+0xa8/0xe0 [stmmac] [ 197.171367] stmmac_setup_tc_block_cb+0x70/0x110 [stmmac] [ 197.171367] tc_setup_cb_destroy+0xb3/0x180 [ 197.171367] fl_hw_destroy_filter+0x94/0xc0 [cls_flower] The above issue is due to previous incorrect implementation of tc_del_vlan_flow(), shown below, that uses flow_cls_offload_flow_rule() to get struct flow_rule *rule which is no longer valid for tc filter delete operation. struct flow_rule *rule = flow_cls_offload_flow_rule(cls); struct flow_dissector *dissector = rule->match.dissector; So, to ensure tc_del_vlan_flow() deletes the right VLAN cls record for earlier configured RX queue (configured by hw_tc) in tc_add_vlan_flow(), this patch introduces stmmac_rfs_entry as driver-side flow_cls_offload record for 'RX frame steering' tc flower, currently used for VLAN priority. The implementation has taken consideration for future extension to include other type RX frame steering such as EtherType based. v2: - Clean up overly extensive backtrace and rewrite git message to better explain the kernel NULL pointer issue.

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: tests: Fix potential NULL dereference in test_cfg80211_parse_colocated_ap() kunit_kzalloc() may return NULL, dereferencing it without NULL check may lead to NULL dereference. Add a NULL check for ies.

In the Linux kernel, the following vulnerability has been resolved: HID: winwing: Add NULL check in winwing_init_led() devm_kasprintf() can return a NULL pointer on failure,but this returned value in winwing_init_led() is not checked. Add NULL check in winwing_init_led(), to handle kernel NULL pointer dereference error.

In the Linux kernel, the following vulnerability has been resolved: mptcp: never allow the PM to close a listener subflow Currently, when deleting an endpoint the netlink PM treverses all the local MPTCP sockets, regardless of their status. If an MPTCP listener socket is bound to the IP matching the delete endpoint, the listener TCP socket will be closed. That is unexpected, the PM should only affect data subflows. Additionally, syzbot was able to trigger a NULL ptr dereference due to the above: general protection fault, probably for non-canonical address 0xdffffc0000000003: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f] CPU: 1 PID: 6550 Comm: syz-executor122 Not tainted 5.16.0-rc4-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:__lock_acquire+0xd7d/0x54a0 kernel/locking/lockdep.c:4897 Code: 0f 0e 41 be 01 00 00 00 0f 86 c8 00 00 00 89 05 69 cc 0f 0e e9 bd 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 da 48 c1 ea 03 <80> 3c 02 00 0f 85 f3 2f 00 00 48 81 3b 20 75 17 8f 0f 84 52 f3 ff RSP: 0018:ffffc90001f2f818 EFLAGS: 00010016 RAX: dffffc0000000000 RBX: 0000000000000018 RCX: 0000000000000000 RDX: 0000000000000003 RSI: 0000000000000000 RDI: 0000000000000001 RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000001 R10: 0000000000000000 R11: 000000000000000a R12: 0000000000000000 R13: ffff88801b98d700 R14: 0000000000000000 R15: 0000000000000001 FS: 00007f177cd3d700(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f177cd1b268 CR3: 000000001dd55000 CR4: 0000000000350ee0 Call Trace: <TASK> lock_acquire kernel/locking/lockdep.c:5637 [inline] lock_acquire+0x1ab/0x510 kernel/locking/lockdep.c:5602 __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] _raw_spin_lock_irqsave+0x39/0x50 kernel/locking/spinlock.c:162 finish_wait+0xc0/0x270 kernel/sched/wait.c:400 inet_csk_wait_for_connect net/ipv4/inet_connection_sock.c:464 [inline] inet_csk_accept+0x7de/0x9d0 net/ipv4/inet_connection_sock.c:497 mptcp_accept+0xe5/0x500 net/mptcp/protocol.c:2865 inet_accept+0xe4/0x7b0 net/ipv4/af_inet.c:739 mptcp_stream_accept+0x2e7/0x10e0 net/mptcp/protocol.c:3345 do_accept+0x382/0x510 net/socket.c:1773 __sys_accept4_file+0x7e/0xe0 net/socket.c:1816 __sys_accept4+0xb0/0x100 net/socket.c:1846 __do_sys_accept net/socket.c:1864 [inline] __se_sys_accept net/socket.c:1861 [inline] __x64_sys_accept+0x71/0xb0 net/socket.c:1861 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f177cd8b8e9 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 b1 14 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f177cd3d308 EFLAGS: 00000246 ORIG_RAX: 000000000000002b RAX: ffffffffffffffda RBX: 00007f177ce13408 RCX: 00007f177cd8b8e9 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003 RBP: 00007f177ce13400 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f177ce1340c R13: 00007f177cde1004 R14: 6d705f706374706d R15: 0000000000022000 </TASK> Fix the issue explicitly skipping MPTCP socket in TCP_LISTEN status.

In the Linux kernel, the following vulnerability has been resolved: platform/x86: int3472: Check for adev == NULL Not all devices have an ACPI companion fwnode, so adev might be NULL. This can e.g. (theoretically) happen when a user manually binds one of the int3472 drivers to another i2c/platform device through sysfs. Add a check for adev not being set and return -ENODEV in that case to avoid a possible NULL pointer deref in skl_int3472_get_acpi_buffer().

In the Linux kernel, the following vulnerability has been resolved: kunit: Fix potential null dereference in kunit_device_driver_test() kunit_kzalloc() may return a NULL pointer, dereferencing it without NULL check may lead to NULL dereference. Add a NULL check for test_state.

In the Linux kernel, the following vulnerability has been resolved: clk: qcom: dispcc-sm6350: Add missing parent_map for a clock If a clk_rcg2 has a parent, it should also have parent_map defined, otherwise we'll get a NULL pointer dereference when calling clk_set_rate like the following: [ 3.388105] Call trace: [ 3.390664] qcom_find_src_index+0x3c/0x70 (P) [ 3.395301] qcom_find_src_index+0x1c/0x70 (L) [ 3.399934] _freq_tbl_determine_rate+0x48/0x100 [ 3.404753] clk_rcg2_determine_rate+0x1c/0x28 [ 3.409387] clk_core_determine_round_nolock+0x58/0xe4 [ 3.421414] clk_core_round_rate_nolock+0x48/0xfc [ 3.432974] clk_core_round_rate_nolock+0xd0/0xfc [ 3.444483] clk_core_set_rate_nolock+0x8c/0x300 [ 3.455886] clk_set_rate+0x38/0x14c Add the parent_map property for the clock where it's missing and also un-inline the parent_data as well to keep the matching parent_map and parent_data together.

In the Linux kernel, the following vulnerability has been resolved: gve: guard XSK operations on the existence of queues This patch predicates the enabling and disabling of XSK pools on the existence of queues. As it stands, if the interface is down, disabling or enabling XSK pools would result in a crash, as the RX queue pointer would be NULL. XSK pool registration will occur as part of the next interface up. Similarly, xsk_wakeup needs be guarded against queues disappearing while the function is executing, so a check against the GVE_PRIV_FLAGS_NAPI_ENABLED flag is added to synchronize with the disabling of the bit and the synchronize_net() in gve_turndown.