In the Linux kernel, the following vulnerability has been resolved: bpf: Fix may_goto with negative offset. Zac's syzbot crafted a bpf prog that exposed two bugs in may_goto. The 1st bug is the way may_goto is patched. When offset is negative it should be patched differently. The 2nd bug is in the verifier: when current state may_goto_depth is equal to visited state may_goto_depth it means there is an actual infinite loop. It's not correct to prune exploration of the program at this point. Note, that this check doesn't limit the program to only one may_goto insn, since 2nd and any further may_goto will increment may_goto_depth only in the queued state pushed for future exploration. The current state will have may_goto_depth == 0 regardless of number of may_goto insns and the verifier has to explore the program until bpf_exit.

In the Linux kernel, the following vulnerability has been resolved: scsi: mpi3mr: Fix issues in mpi3mr_get_all_tgt_info() The function mpi3mr_get_all_tgt_info() has four issues: 1) It calculates valid entry length in alltgt_info assuming the header part of the struct mpi3mr_device_map_info would equal to sizeof(u32). The correct size is sizeof(u64). 2) When it calculates the valid entry length kern_entrylen, it excludes one entry by subtracting 1 from num_devices. 3) It copies num_device by calling memcpy(). Substitution is enough. 4) It does not specify the calculated length to sg_copy_from_buffer(). Instead, it specifies the payload length which is larger than the alltgt_info size. It causes "BUG: KASAN: slab-out-of-bounds". Fix the issues by using the correct header size, removing the subtraction from num_devices, replacing the memcpy() with substitution and specifying the correct length to sg_copy_from_buffer().

In the Linux kernel, the following vulnerability has been resolved: PCI/DPC: Fix use-after-free on concurrent DPC and hot-removal Keith reports a use-after-free when a DPC event occurs concurrently to hot-removal of the same portion of the hierarchy: The dpc_handler() awaits readiness of the secondary bus below the Downstream Port where the DPC event occurred. To do so, it polls the config space of the first child device on the secondary bus. If that child device is concurrently removed, accesses to its struct pci_dev cause the kernel to oops. That's because pci_bridge_wait_for_secondary_bus() neglects to hold a reference on the child device. Before v6.3, the function was only called on resume from system sleep or on runtime resume. Holding a reference wasn't necessary back then because the pciehp IRQ thread could never run concurrently. (On resume from system sleep, IRQs are not enabled until after the resume_noirq phase. And runtime resume is always awaited before a PCI device is removed.) However starting with v6.3, pci_bridge_wait_for_secondary_bus() is also called on a DPC event. Commit 53b54ad074de ("PCI/DPC: Await readiness of secondary bus after reset"), which introduced that, failed to appreciate that pci_bridge_wait_for_secondary_bus() now needs to hold a reference on the child device because dpc_handler() and pciehp may indeed run concurrently. The commit was backported to v5.10+ stable kernels, so that's the oldest one affected. Add the missing reference acquisition. Abridged stack trace: BUG: unable to handle page fault for address: 00000000091400c0 CPU: 15 PID: 2464 Comm: irq/53-pcie-dpc 6.9.0 RIP: pci_bus_read_config_dword+0x17/0x50 pci_dev_wait() pci_bridge_wait_for_secondary_bus() dpc_reset_link() pcie_do_recovery() dpc_handler()

In the Linux kernel, the following vulnerability has been resolved: dev/parport: fix the array out-of-bounds risk Fixed array out-of-bounds issues caused by sprintf by replacing it with snprintf for safer data copying, ensuring the destination buffer is not overflowed. Below is the stack trace I encountered during the actual issue: [ 66.575408s] [pid:5118,cpu4,QThread,4]Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: do_hardware_base_addr+0xcc/0xd0 [parport] [ 66.575408s] [pid:5118,cpu4,QThread,5]CPU: 4 PID: 5118 Comm: QThread Tainted: G S W O 5.10.97-arm64-desktop #7100.57021.2 [ 66.575439s] [pid:5118,cpu4,QThread,6]TGID: 5087 Comm: EFileApp [ 66.575439s] [pid:5118,cpu4,QThread,7]Hardware name: HUAWEI HUAWEI QingYun PGUX-W515x-B081/SP1PANGUXM, BIOS 1.00.07 04/29/2024 [ 66.575439s] [pid:5118,cpu4,QThread,8]Call trace: [ 66.575469s] [pid:5118,cpu4,QThread,9] dump_backtrace+0x0/0x1c0 [ 66.575469s] [pid:5118,cpu4,QThread,0] show_stack+0x14/0x20 [ 66.575469s] [pid:5118,cpu4,QThread,1] dump_stack+0xd4/0x10c [ 66.575500s] [pid:5118,cpu4,QThread,2] panic+0x1d8/0x3bc [ 66.575500s] [pid:5118,cpu4,QThread,3] __stack_chk_fail+0x2c/0x38 [ 66.575500s] [pid:5118,cpu4,QThread,4] do_hardware_base_addr+0xcc/0xd0 [parport]

In the Linux kernel, the following vulnerability has been resolved: nvme: avoid double free special payload If a discard request needs to be retried, and that retry may fail before a new special payload is added, a double free will result. Clear the RQF_SPECIAL_LOAD when the request is cleaned.

In the Linux kernel, the following vulnerability has been resolved: ASoC: topology: Fix references to freed memory Most users after parsing a topology file, release memory used by it, so having pointer references directly into topology file contents is wrong. Use devm_kmemdup(), to allocate memory as needed.

In the Linux kernel, the following vulnerability has been resolved: can: bcm: Fix UAF in bcm_proc_show() BUG: KASAN: slab-use-after-free in bcm_proc_show+0x969/0xa80 Read of size 8 at addr ffff888155846230 by task cat/7862 CPU: 1 PID: 7862 Comm: cat Not tainted 6.5.0-rc1-00153-gc8746099c197 #230 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0xd5/0x150 print_report+0xc1/0x5e0 kasan_report+0xba/0xf0 bcm_proc_show+0x969/0xa80 seq_read_iter+0x4f6/0x1260 seq_read+0x165/0x210 proc_reg_read+0x227/0x300 vfs_read+0x1d5/0x8d0 ksys_read+0x11e/0x240 do_syscall_64+0x35/0xb0 entry_SYSCALL_64_after_hwframe+0x63/0xcd Allocated by task 7846: kasan_save_stack+0x1e/0x40 kasan_set_track+0x21/0x30 __kasan_kmalloc+0x9e/0xa0 bcm_sendmsg+0x264b/0x44e0 sock_sendmsg+0xda/0x180 ____sys_sendmsg+0x735/0x920 ___sys_sendmsg+0x11d/0x1b0 __sys_sendmsg+0xfa/0x1d0 do_syscall_64+0x35/0xb0 entry_SYSCALL_64_after_hwframe+0x63/0xcd Freed by task 7846: kasan_save_stack+0x1e/0x40 kasan_set_track+0x21/0x30 kasan_save_free_info+0x27/0x40 ____kasan_slab_free+0x161/0x1c0 slab_free_freelist_hook+0x119/0x220 __kmem_cache_free+0xb4/0x2e0 rcu_core+0x809/0x1bd0 bcm_op is freed before procfs entry be removed in bcm_release(), this lead to bcm_proc_show() may read the freed bcm_op.

In the Linux kernel, the following vulnerability has been resolved: erspan: do not use skb_mac_header() in ndo_start_xmit() Drivers should not assume skb_mac_header(skb) == skb->data in their ndo_start_xmit(). Use skb_network_offset() and skb_transport_offset() which better describe what is needed in erspan_fb_xmit() and ip6erspan_tunnel_xmit() syzbot reported: WARNING: CPU: 0 PID: 5083 at include/linux/skbuff.h:2873 skb_mac_header include/linux/skbuff.h:2873 [inline] WARNING: CPU: 0 PID: 5083 at include/linux/skbuff.h:2873 ip6erspan_tunnel_xmit+0x1d9c/0x2d90 net/ipv6/ip6_gre.c:962 Modules linked in: CPU: 0 PID: 5083 Comm: syz-executor406 Not tainted 6.3.0-rc2-syzkaller-00866-gd4671cb96fa3 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/02/2023 RIP: 0010:skb_mac_header include/linux/skbuff.h:2873 [inline] RIP: 0010:ip6erspan_tunnel_xmit+0x1d9c/0x2d90 net/ipv6/ip6_gre.c:962 Code: 04 02 41 01 de 84 c0 74 08 3c 03 0f 8e 1c 0a 00 00 45 89 b4 24 c8 00 00 00 c6 85 77 fe ff ff 01 e9 33 e7 ff ff e8 b4 27 a1 f8 <0f> 0b e9 b6 e7 ff ff e8 a8 27 a1 f8 49 8d bf f0 0c 00 00 48 b8 00 RSP: 0018:ffffc90003b2f830 EFLAGS: 00010293 RAX: 0000000000000000 RBX: 000000000000ffff RCX: 0000000000000000 RDX: ffff888021273a80 RSI: ffffffff88e1bd4c RDI: 0000000000000003 RBP: ffffc90003b2f9d8 R08: 0000000000000003 R09: 000000000000ffff R10: 000000000000ffff R11: 0000000000000000 R12: ffff88802b28da00 R13: 00000000000000d0 R14: ffff88807e25b6d0 R15: ffff888023408000 FS: 0000555556a61300(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055e5b11eb6e8 CR3: 0000000027c1b000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __netdev_start_xmit include/linux/netdevice.h:4900 [inline] netdev_start_xmit include/linux/netdevice.h:4914 [inline] __dev_direct_xmit+0x504/0x730 net/core/dev.c:4300 dev_direct_xmit include/linux/netdevice.h:3088 [inline] packet_xmit+0x20a/0x390 net/packet/af_packet.c:285 packet_snd net/packet/af_packet.c:3075 [inline] packet_sendmsg+0x31a0/0x5150 net/packet/af_packet.c:3107 sock_sendmsg_nosec net/socket.c:724 [inline] sock_sendmsg+0xde/0x190 net/socket.c:747 __sys_sendto+0x23a/0x340 net/socket.c:2142 __do_sys_sendto net/socket.c:2154 [inline] __se_sys_sendto net/socket.c:2150 [inline] __x64_sys_sendto+0xe1/0x1b0 net/socket.c:2150 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7f123aaa1039 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 b1 14 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffc15d12058 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f123aaa1039 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003 RBP: 0000000000000000 R08: 0000000020000040 R09: 0000000000000014 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f123aa648c0 R13: 431bde82d7b634db R14: 0000000000000000 R15: 0000000000000000

issues with partially successful P2M updates on x86 T[his CNA information record relates to multiple CVEs; the text explains which aspects/vulnerabilities correspond to which CVE.] x86 HVM and PVH guests may be started in populate-on-demand (PoD) mode, to provide a way for them to later easily have more memory assigned. Guests are permitted to control certain P2M aspects of individual pages via hypercalls. These hypercalls may act on ranges of pages specified via page orders (resulting in a power-of-2 number of pages). In some cases the hypervisor carries out the requests by splitting them into smaller chunks. Error handling in certain PoD cases has been insufficient in that in particular partial success of some operations was not properly accounted for. There are two code paths affected - page removal (CVE-2021-28705) and insertion of new pages (CVE-2021-28709). (We provide one patch which combines the fix to both issues.)

In the Linux kernel, the following vulnerability has been resolved: cachefiles: Set object to close if ondemand_id < 0 in copen If copen is maliciously called in the user mode, it may delete the request corresponding to the random id. And the request may have not been read yet. Note that when the object is set to reopen, the open request will be done with the still reopen state in above case. As a result, the request corresponding to this object is always skipped in select_req function, so the read request is never completed and blocks other process. Fix this issue by simply set object to close if its id < 0 in copen.

In the Linux kernel, the following vulnerability has been resolved: ata: libata-core: Fix double free on error If e.g. the ata_port_alloc() call in ata_host_alloc() fails, we will jump to the err_out label, which will call devres_release_group(). devres_release_group() will trigger a call to ata_host_release(). ata_host_release() calls kfree(host), so executing the kfree(host) in ata_host_alloc() will lead to a double free: kernel BUG at mm/slub.c:553! Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 11 PID: 599 Comm: (udev-worker) Not tainted 6.10.0-rc5 #47 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:kfree+0x2cf/0x2f0 Code: 5d 41 5e 41 5f 5d e9 80 d6 ff ff 4d 89 f1 41 b8 01 00 00 00 48 89 d9 48 89 da RSP: 0018:ffffc90000f377f0 EFLAGS: 00010246 RAX: ffff888112b1f2c0 RBX: ffff888112b1f2c0 RCX: ffff888112b1f320 RDX: 000000000000400b RSI: ffffffffc02c9de5 RDI: ffff888112b1f2c0 RBP: ffffc90000f37830 R08: 0000000000000000 R09: 0000000000000000 R10: ffffc90000f37610 R11: 617461203a736b6e R12: ffffea00044ac780 R13: ffff888100046400 R14: ffffffffc02c9de5 R15: 0000000000000006 FS: 00007f2f1cabe980(0000) GS:ffff88813b380000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f2f1c3acf75 CR3: 0000000111724000 CR4: 0000000000750ef0 PKRU: 55555554 Call Trace: <TASK> ? __die_body.cold+0x19/0x27 ? die+0x2e/0x50 ? do_trap+0xca/0x110 ? do_error_trap+0x6a/0x90 ? kfree+0x2cf/0x2f0 ? exc_invalid_op+0x50/0x70 ? kfree+0x2cf/0x2f0 ? asm_exc_invalid_op+0x1a/0x20 ? ata_host_alloc+0xf5/0x120 [libata] ? ata_host_alloc+0xf5/0x120 [libata] ? kfree+0x2cf/0x2f0 ata_host_alloc+0xf5/0x120 [libata] ata_host_alloc_pinfo+0x14/0xa0 [libata] ahci_init_one+0x6c9/0xd20 [ahci] Ensure that we will not call kfree(host) twice, by performing the kfree() only if the devres_open_group() call failed.

In the Linux kernel, the following vulnerability has been resolved: block: avoid to reuse `hctx` not removed from cpuhp callback list If the 'hctx' isn't removed from cpuhp callback list, we can't reuse it, otherwise use-after-free may be triggered.

In the Linux kernel, the following vulnerability has been resolved: tipc: Return non-zero value from tipc_udp_addr2str() on error tipc_udp_addr2str() should return non-zero value if the UDP media address is invalid. Otherwise, a buffer overflow access can occur in tipc_media_addr_printf(). Fix this by returning 1 on an invalid UDP media address.

ImageMagick is a free and open-source software suite, used for editing and manipulating digital images. The `AppImage` version `ImageMagick` might use an empty path when setting `MAGICK_CONFIGURE_PATH` and `LD_LIBRARY_PATH` environment variables while executing, which might lead to arbitrary code execution by loading malicious configuration files or shared libraries in the current working directory while executing `ImageMagick`. The vulnerability is fixed in 7.11-36.

In the Linux kernel, the following vulnerability has been resolved: drm/tests: helpers: Avoid a driver uaf when using __drm_kunit_helper_alloc_drm_device() the driver may be dereferenced by device-managed resources up until the device is freed, which is typically later than the kunit-managed resource code frees it. Fix this by simply make the driver device-managed as well. In short, the sequence leading to the UAF is as follows: INIT: Code allocates a struct device as a kunit-managed resource. Code allocates a drm driver as a kunit-managed resource. Code allocates a drm device as a device-managed resource. EXIT: Kunit resource cleanup frees the drm driver Kunit resource cleanup puts the struct device, which starts a device-managed resource cleanup device-managed cleanup calls drm_dev_put() drm_dev_put() dereferences the (now freed) drm driver -> Boom. Related KASAN message: [55272.551542] ================================================================== [55272.551551] BUG: KASAN: slab-use-after-free in drm_dev_put.part.0+0xd4/0xe0 [drm] [55272.551603] Read of size 8 at addr ffff888127502828 by task kunit_try_catch/10353 [55272.551612] CPU: 4 PID: 10353 Comm: kunit_try_catch Tainted: G U N 6.5.0-rc7+ #155 [55272.551620] Hardware name: ASUS System Product Name/PRIME B560M-A AC, BIOS 0403 01/26/2021 [55272.551626] Call Trace: [55272.551629] <TASK> [55272.551633] dump_stack_lvl+0x57/0x90 [55272.551639] print_report+0xcf/0x630 [55272.551645] ? _raw_spin_lock_irqsave+0x5f/0x70 [55272.551652] ? drm_dev_put.part.0+0xd4/0xe0 [drm] [55272.551694] kasan_report+0xd7/0x110 [55272.551699] ? drm_dev_put.part.0+0xd4/0xe0 [drm] [55272.551742] drm_dev_put.part.0+0xd4/0xe0 [drm] [55272.551783] devres_release_all+0x15d/0x1f0 [55272.551790] ? __pfx_devres_release_all+0x10/0x10 [55272.551797] device_unbind_cleanup+0x16/0x1a0 [55272.551802] device_release_driver_internal+0x3e5/0x540 [55272.551808] ? kobject_put+0x5d/0x4b0 [55272.551814] bus_remove_device+0x1f1/0x3f0 [55272.551819] device_del+0x342/0x910 [55272.551826] ? __pfx_device_del+0x10/0x10 [55272.551830] ? lock_release+0x339/0x5e0 [55272.551836] ? kunit_remove_resource+0x128/0x290 [kunit] [55272.551845] ? __pfx_lock_release+0x10/0x10 [55272.551851] platform_device_del.part.0+0x1f/0x1e0 [55272.551856] ? _raw_spin_unlock_irqrestore+0x30/0x60 [55272.551863] kunit_remove_resource+0x195/0x290 [kunit] [55272.551871] ? _raw_spin_unlock_irqrestore+0x30/0x60 [55272.551877] kunit_cleanup+0x78/0x120 [kunit] [55272.551885] ? __kthread_parkme+0xc1/0x1f0 [55272.551891] ? __pfx_kunit_try_run_case_cleanup+0x10/0x10 [kunit] [55272.551900] ? __pfx_kunit_generic_run_threadfn_adapter+0x10/0x10 [kunit] [55272.551909] kunit_generic_run_threadfn_adapter+0x4a/0x90 [kunit] [55272.551919] kthread+0x2e7/0x3c0 [55272.551924] ? __pfx_kthread+0x10/0x10 [55272.551929] ret_from_fork+0x2d/0x70 [55272.551935] ? __pfx_kthread+0x10/0x10 [55272.551940] ret_from_fork_asm+0x1b/0x30 [55272.551948] </TASK> [55272.551953] Allocated by task 10351: [55272.551956] kasan_save_stack+0x1c/0x40 [55272.551962] kasan_set_track+0x21/0x30 [55272.551966] __kasan_kmalloc+0x8b/0x90 [55272.551970] __kmalloc+0x5e/0x160 [55272.551976] kunit_kmalloc_array+0x1c/0x50 [kunit] [55272.551984] drm_exec_test_init+0xfa/0x2c0 [drm_exec_test] [55272.551991] kunit_try_run_case+0xdd/0x250 [kunit] [55272.551999] kunit_generic_run_threadfn_adapter+0x4a/0x90 [kunit] [55272.552008] kthread+0x2e7/0x3c0 [55272.552012] ret_from_fork+0x2d/0x70 [55272.552017] ret_from_fork_asm+0x1b/0x30 [55272.552024] Freed by task 10353: [55272.552027] kasan_save_stack+0x1c/0x40 [55272.552032] kasan_set_track+0x21/0x30 [55272.552036] kasan_save_free_info+0x27/0x40 [55272.552041] __kasan_slab_free+0x106/0x180 [55272.552046] slab_free_freelist_hook+0xb3/0x160 [55272.552051] __kmem_cache_free+0xb2/0x290 [55272.552056] kunit_remove_resource+0x195/0x290 [kunit] [55272.552064] kunit_cleanup+0x7 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm/i915/gt: Fix potential UAF by revoke of fence registers CI has been sporadically reporting the following issue triggered by igt@i915_selftest@live@hangcheck on ADL-P and similar machines: <6> [414.049203] i915: Running intel_hangcheck_live_selftests/igt_reset_evict_fence ... <6> [414.068804] i915 0000:00:02.0: [drm] GT0: GUC: submission enabled <6> [414.068812] i915 0000:00:02.0: [drm] GT0: GUC: SLPC enabled <3> [414.070354] Unable to pin Y-tiled fence; err:-4 <3> [414.071282] i915_vma_revoke_fence:301 GEM_BUG_ON(!i915_active_is_idle(&fence->active)) ... <4>[ 609.603992] ------------[ cut here ]------------ <2>[ 609.603995] kernel BUG at drivers/gpu/drm/i915/gt/intel_ggtt_fencing.c:301! <4>[ 609.604003] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI <4>[ 609.604006] CPU: 0 PID: 268 Comm: kworker/u64:3 Tainted: G U W 6.9.0-CI_DRM_14785-g1ba62f8cea9c+ #1 <4>[ 609.604008] Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-P DDR4 RVP, BIOS RPLPFWI1.R00.4035.A00.2301200723 01/20/2023 <4>[ 609.604010] Workqueue: i915 __i915_gem_free_work [i915] <4>[ 609.604149] RIP: 0010:i915_vma_revoke_fence+0x187/0x1f0 [i915] ... <4>[ 609.604271] Call Trace: <4>[ 609.604273] <TASK> ... <4>[ 609.604716] __i915_vma_evict+0x2e9/0x550 [i915] <4>[ 609.604852] __i915_vma_unbind+0x7c/0x160 [i915] <4>[ 609.604977] force_unbind+0x24/0xa0 [i915] <4>[ 609.605098] i915_vma_destroy+0x2f/0xa0 [i915] <4>[ 609.605210] __i915_gem_object_pages_fini+0x51/0x2f0 [i915] <4>[ 609.605330] __i915_gem_free_objects.isra.0+0x6a/0xc0 [i915] <4>[ 609.605440] process_scheduled_works+0x351/0x690 ... In the past, there were similar failures reported by CI from other IGT tests, observed on other platforms. Before commit 63baf4f3d587 ("drm/i915/gt: Only wait for GPU activity before unbinding a GGTT fence"), i915_vma_revoke_fence() was waiting for idleness of vma->active via fence_update(). That commit introduced vma->fence->active in order for the fence_update() to be able to wait selectively on that one instead of vma->active since only idleness of fence registers was needed. But then, another commit 0d86ee35097a ("drm/i915/gt: Make fence revocation unequivocal") replaced the call to fence_update() in i915_vma_revoke_fence() with only fence_write(), and also added that GEM_BUG_ON(!i915_active_is_idle(&fence->active)) in front. No justification was provided on why we might then expect idleness of vma->fence->active without first waiting on it. The issue can be potentially caused by a race among revocation of fence registers on one side and sequential execution of signal callbacks invoked on completion of a request that was using them on the other, still processed in parallel to revocation of those fence registers. Fix it by waiting for idleness of vma->fence->active in i915_vma_revoke_fence(). (cherry picked from commit 24bb052d3dd499c5956abad5f7d8e4fd07da7fb1)

In the Linux kernel, the following vulnerability has been resolved: mISDN: Fix a use after free in hfcmulti_tx() Don't dereference *sp after calling dev_kfree_skb(*sp).

In the Linux kernel, the following vulnerability has been resolved: gpio: davinci: Validate the obtained number of IRQs Value of pdata->gpio_unbanked is taken from Device Tree. In case of broken DT due to any error this value can be any. Without this value validation there can be out of chips->irqs array boundaries access in davinci_gpio_probe(). Validate the obtained nirq value so that it won't exceed the maximum number of IRQs per bank. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix inode number range checks Patch series "nilfs2: fix potential issues related to reserved inodes". This series fixes one use-after-free issue reported by syzbot, caused by nilfs2's internal inode being exposed in the namespace on a corrupted filesystem, and a couple of flaws that cause problems if the starting number of non-reserved inodes written in the on-disk super block is intentionally (or corruptly) changed from its default value. This patch (of 3): In the current implementation of nilfs2, "nilfs->ns_first_ino", which gives the first non-reserved inode number, is read from the superblock, but its lower limit is not checked. As a result, if a number that overlaps with the inode number range of reserved inodes such as the root directory or metadata files is set in the super block parameter, the inode number test macros (NILFS_MDT_INODE and NILFS_VALID_INODE) will not function properly. In addition, these test macros use left bit-shift calculations using with the inode number as the shift count via the BIT macro, but the result of a shift calculation that exceeds the bit width of an integer is undefined in the C specification, so if "ns_first_ino" is set to a large value other than the default value NILFS_USER_INO (=11), the macros may potentially malfunction depending on the environment. Fix these issues by checking the lower bound of "nilfs->ns_first_ino" and by preventing bit shifts equal to or greater than the NILFS_USER_INO constant in the inode number test macros. Also, change the type of "ns_first_ino" from signed integer to unsigned integer to avoid the need for type casting in comparisons such as the lower bound check introduced this time.

In the Linux kernel, the following vulnerability has been resolved: PCI/MSI: Fix UAF in msi_capability_init KFENCE reports the following UAF: BUG: KFENCE: use-after-free read in __pci_enable_msi_range+0x2c0/0x488 Use-after-free read at 0x0000000024629571 (in kfence-#12): __pci_enable_msi_range+0x2c0/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 kfence-#12: 0x0000000008614900-0x00000000e06c228d, size=104, cache=kmalloc-128 allocated by task 81 on cpu 7 at 10.808142s: __kmem_cache_alloc_node+0x1f0/0x2bc kmalloc_trace+0x44/0x138 msi_alloc_desc+0x3c/0x9c msi_domain_insert_msi_desc+0x30/0x78 msi_setup_msi_desc+0x13c/0x184 __pci_enable_msi_range+0x258/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 freed by task 81 on cpu 7 at 10.811436s: msi_domain_free_descs+0xd4/0x10c msi_domain_free_locked.part.0+0xc0/0x1d8 msi_domain_alloc_irqs_all_locked+0xb4/0xbc pci_msi_setup_msi_irqs+0x30/0x4c __pci_enable_msi_range+0x2a8/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 Descriptor allocation done in: __pci_enable_msi_range msi_capability_init msi_setup_msi_desc msi_insert_msi_desc msi_domain_insert_msi_desc msi_alloc_desc ... Freed in case of failure in __msi_domain_alloc_locked() __pci_enable_msi_range msi_capability_init pci_msi_setup_msi_irqs msi_domain_alloc_irqs_all_locked msi_domain_alloc_locked __msi_domain_alloc_locked => fails msi_domain_free_locked ... That failure propagates back to pci_msi_setup_msi_irqs() in msi_capability_init() which accesses the descriptor for unmasking in the error exit path. Cure it by copying the descriptor and using the copy for the error exit path unmask operation. [ tglx: Massaged change log ]

In the Linux kernel, the following vulnerability has been resolved: RDMA/bnxt_re: Fix out of bound check Driver exports pacing stats only on GenP5 and P7 adapters. But while parsing the pacing stats, driver has a check for "rdev->dbr_pacing". This caused a trace when KASAN is enabled. BUG: KASAN: slab-out-of-bounds in bnxt_re_get_hw_stats+0x2b6a/0x2e00 [bnxt_re] Write of size 8 at addr ffff8885942a6340 by task modprobe/4809

In the Linux kernel, the following vulnerability has been resolved: cachefiles: cyclic allocation of msg_id to avoid reuse Reusing the msg_id after a maliciously completed reopen request may cause a read request to remain unprocessed and result in a hung, as shown below: t1 | t2 | t3 ------------------------------------------------- cachefiles_ondemand_select_req cachefiles_ondemand_object_is_close(A) cachefiles_ondemand_set_object_reopening(A) queue_work(fscache_object_wq, &info->work) ondemand_object_worker cachefiles_ondemand_init_object(A) cachefiles_ondemand_send_req(OPEN) // get msg_id 6 wait_for_completion(&req_A->done) cachefiles_ondemand_daemon_read // read msg_id 6 req_A cachefiles_ondemand_get_fd copy_to_user // Malicious completion msg_id 6 copen 6,-1 cachefiles_ondemand_copen complete(&req_A->done) // will not set the object to close // because ondemand_id && fd is valid. // ondemand_object_worker() is done // but the object is still reopening. // new open req_B cachefiles_ondemand_init_object(B) cachefiles_ondemand_send_req(OPEN) // reuse msg_id 6 process_open_req copen 6,A.size // The expected failed copen was executed successfully Expect copen to fail, and when it does, it closes fd, which sets the object to close, and then close triggers reopen again. However, due to msg_id reuse resulting in a successful copen, the anonymous fd is not closed until the daemon exits. Therefore read requests waiting for reopen to complete may trigger hung task. To avoid this issue, allocate the msg_id cyclically to avoid reusing the msg_id for a very short duration of time.

In the Linux kernel, the following vulnerability has been resolved: net: wwan: iosm: Fix tainted pointer delete is case of region creation fail In case of region creation fail in ipc_devlink_create_region(), previously created regions delete process starts from tainted pointer which actually holds error code value. Fix this bug by decreasing region index before delete. Found by Linux Verification Center (linuxtesting.org) with SVACE.

Incorrect default permissions in .NET allows an authorized attacker to elevate privileges locally.

In the Linux kernel, the following vulnerability has been resolved: xhci: Handle TD clearing for multiple streams case When multiple streams are in use, multiple TDs might be in flight when an endpoint is stopped. We need to issue a Set TR Dequeue Pointer for each, to ensure everything is reset properly and the caches cleared. Change the logic so that any N>1 TDs found active for different streams are deferred until after the first one is processed, calling xhci_invalidate_cancelled_tds() again from xhci_handle_cmd_set_deq() to queue another command until we are done with all of them. Also change the error/"should never happen" paths to ensure we at least clear any affected TDs, even if we can't issue a command to clear the hardware cache, and complain loudly with an xhci_warn() if this ever happens. This problem case dates back to commit e9df17eb1408 ("USB: xhci: Correct assumptions about number of rings per endpoint.") early on in the XHCI driver's life, when stream support was first added. It was then identified but not fixed nor made into a warning in commit 674f8438c121 ("xhci: split handling halted endpoints into two steps"), which added a FIXME comment for the problem case (without materially changing the behavior as far as I can tell, though the new logic made the problem more obvious). Then later, in commit 94f339147fc3 ("xhci: Fix failure to give back some cached cancelled URBs."), it was acknowledged again. [Mathias: commit 94f339147fc3 ("xhci: Fix failure to give back some cached cancelled URBs.") was a targeted regression fix to the previously mentioned patch. Users reported issues with usb stuck after unmounting/disconnecting UAS devices. This rolled back the TD clearing of multiple streams to its original state.] Apparently the commit author was aware of the problem (yet still chose to submit it): It was still mentioned as a FIXME, an xhci_dbg() was added to log the problem condition, and the remaining issue was mentioned in the commit description. The choice of making the log type xhci_dbg() for what is, at this point, a completely unhandled and known broken condition is puzzling and unfortunate, as it guarantees that no actual users would see the log in production, thereby making it nigh undebuggable (indeed, even if you turn on DEBUG, the message doesn't really hint at there being a problem at all). It took me *months* of random xHC crashes to finally find a reliable repro and be able to do a deep dive debug session, which could all have been avoided had this unhandled, broken condition been actually reported with a warning, as it should have been as a bug intentionally left in unfixed (never mind that it shouldn't have been left in at all). > Another fix to solve clearing the caches of all stream rings with > cancelled TDs is needed, but not as urgent. 3 years after that statement and 14 years after the original bug was introduced, I think it's finally time to fix it. And maybe next time let's not leave bugs unfixed (that are actually worse than the original bug), and let's actually get people to review kernel commits please. Fixes xHC crashes and IOMMU faults with UAS devices when handling errors/faults. Easiest repro is to use `hdparm` to mark an early sector (e.g. 1024) on a disk as bad, then `cat /dev/sdX > /dev/null` in a loop. At least in the case of JMicron controllers, the read errors end up having to cancel two TDs (for two queued requests to different streams) and the one that didn't get cleared properly ends up faulting the xHC entirely when it tries to access DMA pages that have since been unmapped, referred to by the stale TDs. This normally happens quickly (after two or three loops). After this fix, I left the `cat` in a loop running overnight and experienced no xHC failures, with all read errors recovered properly. Repro'd and tested on an Apple M1 Mac Mini (dwc3 host). On systems without an IOMMU, this bug would instead silently corrupt freed memory, making this a ---truncated---

In the Linux kernel, the following vulnerability has been resolved: usb: typec: tcpm: fix use-after-free case in tcpm_register_source_caps There could be a potential use-after-free case in tcpm_register_source_caps(). This could happen when: * new (say invalid) source caps are advertised * the existing source caps are unregistered * tcpm_register_source_caps() returns with an error as usb_power_delivery_register_capabilities() fails This causes port->partner_source_caps to hold on to the now freed source caps. Reset port->partner_source_caps value to NULL after unregistering existing source caps.

In the Linux kernel, the following vulnerability has been resolved: powerpc/pseries: Enforce hcall result buffer validity and size plpar_hcall(), plpar_hcall9(), and related functions expect callers to provide valid result buffers of certain minimum size. Currently this is communicated only through comments in the code and the compiler has no idea. For example, if I write a bug like this: long retbuf[PLPAR_HCALL_BUFSIZE]; // should be PLPAR_HCALL9_BUFSIZE plpar_hcall9(H_ALLOCATE_VAS_WINDOW, retbuf, ...); This compiles with no diagnostics emitted, but likely results in stack corruption at runtime when plpar_hcall9() stores results past the end of the array. (To be clear this is a contrived example and I have not found a real instance yet.) To make this class of error less likely, we can use explicitly-sized array parameters instead of pointers in the declarations for the hcall APIs. When compiled with -Warray-bounds[1], the code above now provokes a diagnostic like this: error: array argument is too small; is of size 32, callee requires at least 72 [-Werror,-Warray-bounds] 60 | plpar_hcall9(H_ALLOCATE_VAS_WINDOW, retbuf, | ^ ~~~~~~ [1] Enabled for LLVM builds but not GCC for now. See commit 0da6e5fd6c37 ("gcc: disable '-Warray-bounds' for gcc-13 too") and related changes.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Refactor amdgpu_gem_va_ioctl for Handling Last Fence Update and Timeline Management v4 This commit simplifies the amdgpu_gem_va_ioctl function, key updates include: - Moved the logic for managing the last update fence directly into amdgpu_gem_va_update_vm. - Introduced checks for the timeline point to enable conditional replacement or addition of fences. v2: Addressed review comments from Christian. v3: Updated comments (Christian). v4: The previous version selected the fence too early and did not manage its reference correctly, which could lead to stale or freed fences being used. This resulted in refcount underflows and could crash when updating GPU timelines. The fence is now chosen only after the VA mapping work is completed, and its reference is taken safely. After exporting it to the VM timeline syncobj, the driver always drops its local fence reference, ensuring balanced refcounting and avoiding use-after-free on dma_fence. Crash signature: [ 205.828135] refcount_t: underflow; use-after-free. [ 205.832963] WARNING: CPU: 30 PID: 7274 at lib/refcount.c:28 refcount_warn_saturate+0xbe/0x110 ... [ 206.074014] Call Trace: [ 206.076488] <TASK> [ 206.078608] amdgpu_gem_va_ioctl+0x6ea/0x740 [amdgpu] [ 206.084040] ? __pfx_amdgpu_gem_va_ioctl+0x10/0x10 [amdgpu] [ 206.089994] drm_ioctl_kernel+0x86/0xe0 [drm] [ 206.094415] drm_ioctl+0x26e/0x520 [drm] [ 206.098424] ? __pfx_amdgpu_gem_va_ioctl+0x10/0x10 [amdgpu] [ 206.104402] amdgpu_drm_ioctl+0x4b/0x80 [amdgpu] [ 206.109387] __x64_sys_ioctl+0x96/0xe0 [ 206.113156] do_syscall_64+0x66/0x2d0 ... [ 206.553351] BUG: unable to handle page fault for address: ffffffffc0dfde90 ... [ 206.553378] RIP: 0010:dma_fence_signal_timestamp_locked+0x39/0xe0 ... [ 206.553405] Call Trace: [ 206.553409] <IRQ> [ 206.553415] ? __pfx_drm_sched_fence_free_rcu+0x10/0x10 [gpu_sched] [ 206.553424] dma_fence_signal+0x30/0x60 [ 206.553427] drm_sched_job_done.isra.0+0x123/0x150 [gpu_sched] [ 206.553434] dma_fence_signal_timestamp_locked+0x6e/0xe0 [ 206.553437] dma_fence_signal+0x30/0x60 [ 206.553441] amdgpu_fence_process+0xd8/0x150 [amdgpu] [ 206.553854] sdma_v4_0_process_trap_irq+0x97/0xb0 [amdgpu] [ 206.554353] edac_mce_amd(E) ee1004(E) [ 206.554270] amdgpu_irq_dispatch+0x150/0x230 [amdgpu] [ 206.554702] amdgpu_ih_process+0x6a/0x180 [amdgpu] [ 206.555101] amdgpu_irq_handler+0x23/0x60 [amdgpu] [ 206.555500] __handle_irq_event_percpu+0x4a/0x1c0 [ 206.555506] handle_irq_event+0x38/0x80 [ 206.555509] handle_edge_irq+0x92/0x1e0 [ 206.555513] __common_interrupt+0x3e/0xb0 [ 206.555519] common_interrupt+0x80/0xa0 [ 206.555525] </IRQ> [ 206.555527] <TASK> ... [ 206.555650] RIP: 0010:dma_fence_signal_timestamp_locked+0x39/0xe0 ... [ 206.555667] Kernel panic - not syncing: Fatal exception in interrupt

In the Linux kernel, the following vulnerability has been resolved: cachefiles: flush all requests after setting CACHEFILES_DEAD In ondemand mode, when the daemon is processing an open request, if the kernel flags the cache as CACHEFILES_DEAD, the cachefiles_daemon_write() will always return -EIO, so the daemon can't pass the copen to the kernel. Then the kernel process that is waiting for the copen triggers a hung_task. Since the DEAD state is irreversible, it can only be exited by closing /dev/cachefiles. Therefore, after calling cachefiles_io_error() to mark the cache as CACHEFILES_DEAD, if in ondemand mode, flush all requests to avoid the above hungtask. We may still be able to read some of the cached data before closing the fd of /dev/cachefiles. Note that this relies on the patch that adds reference counting to the req, otherwise it may UAF.

In the Linux kernel, the following vulnerability has been resolved: bpf: Defer work in bpf_timer_cancel_and_free Currently, the same case as previous patch (two timer callbacks trying to cancel each other) can be invoked through bpf_map_update_elem as well, or more precisely, freeing map elements containing timers. Since this relies on hrtimer_cancel as well, it is prone to the same deadlock situation as the previous patch. It would be sufficient to use hrtimer_try_to_cancel to fix this problem, as the timer cannot be enqueued after async_cancel_and_free. Once async_cancel_and_free has been done, the timer must be reinitialized before it can be armed again. The callback running in parallel trying to arm the timer will fail, and freeing bpf_hrtimer without waiting is sufficient (given kfree_rcu), and bpf_timer_cb will return HRTIMER_NORESTART, preventing the timer from being rearmed again. However, there exists a UAF scenario where the callback arms the timer before entering this function, such that if cancellation fails (due to timer callback invoking this routine, or the target timer callback running concurrently). In such a case, if the timer expiration is significantly far in the future, the RCU grace period expiration happening before it will free the bpf_hrtimer state and along with it the struct hrtimer, that is enqueued. Hence, it is clear cancellation needs to occur after async_cancel_and_free, and yet it cannot be done inline due to deadlock issues. We thus modify bpf_timer_cancel_and_free to defer work to the global workqueue, adding a work_struct alongside rcu_head (both used at _different_ points of time, so can share space). Update existing code comments to reflect the new state of affairs.

A use-after-free vulnerability in the Linux kernel's netfilter: nf_tables component can be exploited to achieve local privilege escalation. On an error when building a nftables rule, deactivating immediate expressions in nft_immediate_deactivate() can lead unbinding the chain and objects be deactivated but later used. We recommend upgrading past commit 0a771f7b266b02d262900c75f1e175c7fe76fec2.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: defer exposing anon_fd until after copy_to_user() succeeds After installing the anonymous fd, we can now see it in userland and close it. However, at this point we may not have gotten the reference count of the cache, but we will put it during colse fd, so this may cause a cache UAF. So grab the cache reference count before fd_install(). In addition, by kernel convention, fd is taken over by the user land after fd_install(), and the kernel should not call close_fd() after that, i.e., it should call fd_install() after everything is ready, thus fd_install() is called after copy_to_user() succeeds.

In the Linux kernel, the following vulnerability has been resolved: scsi: mpt3sas: Avoid test/set_bit() operating in non-allocated memory There is a potential out-of-bounds access when using test_bit() on a single word. The test_bit() and set_bit() functions operate on long values, and when testing or setting a single word, they can exceed the word boundary. KASAN detects this issue and produces a dump: BUG: KASAN: slab-out-of-bounds in _scsih_add_device.constprop.0 (./arch/x86/include/asm/bitops.h:60 ./include/asm-generic/bitops/instrumented-atomic.h:29 drivers/scsi/mpt3sas/mpt3sas_scsih.c:7331) mpt3sas Write of size 8 at addr ffff8881d26e3c60 by task kworker/u1536:2/2965 For full log, please look at [1]. Make the allocation at least the size of sizeof(unsigned long) so that set_bit() and test_bit() have sufficient room for read/write operations without overwriting unallocated memory. [1] Link: https://lore.kernel.org/all/ZkNcALr3W3KGYYJG@gmail.com/

In the Linux kernel, the following vulnerability has been resolved: netns: Make get_net_ns() handle zero refcount net Syzkaller hit a warning: refcount_t: addition on 0; use-after-free. WARNING: CPU: 3 PID: 7890 at lib/refcount.c:25 refcount_warn_saturate+0xdf/0x1d0 Modules linked in: CPU: 3 PID: 7890 Comm: tun Not tainted 6.10.0-rc3-00100-gcaa4f9578aba-dirty #310 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:refcount_warn_saturate+0xdf/0x1d0 Code: 41 49 04 31 ff 89 de e8 9f 1e cd fe 84 db 75 9c e8 76 26 cd fe c6 05 b6 41 49 04 01 90 48 c7 c7 b8 8e 25 86 e8 d2 05 b5 fe 90 <0f> 0b 90 90 e9 79 ff ff ff e8 53 26 cd fe 0f b6 1 RSP: 0018:ffff8881067b7da0 EFLAGS: 00010286 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff811c72ac RDX: ffff8881026a2140 RSI: ffffffff811c72b5 RDI: 0000000000000001 RBP: ffff8881067b7db0 R08: 0000000000000000 R09: 205b5d3730353139 R10: 0000000000000000 R11: 205d303938375420 R12: ffff8881086500c4 R13: ffff8881086500c4 R14: ffff8881086500b0 R15: ffff888108650040 FS: 00007f5b2961a4c0(0000) GS:ffff88823bd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055d7ed36fd18 CR3: 00000001482f6000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? show_regs+0xa3/0xc0 ? __warn+0xa5/0x1c0 ? refcount_warn_saturate+0xdf/0x1d0 ? report_bug+0x1fc/0x2d0 ? refcount_warn_saturate+0xdf/0x1d0 ? handle_bug+0xa1/0x110 ? exc_invalid_op+0x3c/0xb0 ? asm_exc_invalid_op+0x1f/0x30 ? __warn_printk+0xcc/0x140 ? __warn_printk+0xd5/0x140 ? refcount_warn_saturate+0xdf/0x1d0 get_net_ns+0xa4/0xc0 ? __pfx_get_net_ns+0x10/0x10 open_related_ns+0x5a/0x130 __tun_chr_ioctl+0x1616/0x2370 ? __sanitizer_cov_trace_switch+0x58/0xa0 ? __sanitizer_cov_trace_const_cmp2+0x1c/0x30 ? __pfx_tun_chr_ioctl+0x10/0x10 tun_chr_ioctl+0x2f/0x40 __x64_sys_ioctl+0x11b/0x160 x64_sys_call+0x1211/0x20d0 do_syscall_64+0x9e/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f5b28f165d7 Code: b3 66 90 48 8b 05 b1 48 2d 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 81 48 2d 00 8 RSP: 002b:00007ffc2b59c5e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f5b28f165d7 RDX: 0000000000000000 RSI: 00000000000054e3 RDI: 0000000000000003 RBP: 00007ffc2b59c650 R08: 00007f5b291ed8c0 R09: 00007f5b2961a4c0 R10: 0000000029690010 R11: 0000000000000246 R12: 0000000000400730 R13: 00007ffc2b59cf40 R14: 0000000000000000 R15: 0000000000000000 </TASK> Kernel panic - not syncing: kernel: panic_on_warn set ... This is trigger as below: ns0 ns1 tun_set_iff() //dev is tun0 tun->dev = dev //ip link set tun0 netns ns1 put_net() //ref is 0 __tun_chr_ioctl() //TUNGETDEVNETNS net = dev_net(tun->dev); open_related_ns(&net->ns, get_net_ns); //ns1 get_net_ns() get_net() //addition on 0 Use maybe_get_net() in get_net_ns in case net's ref is zero to fix this

In the Linux kernel, the following vulnerability has been resolved: drm/vc4: don't check if plane->state->fb == state->fb Currently, when using non-blocking commits, we can see the following kernel warning: [ 110.908514] ------------[ cut here ]------------ [ 110.908529] refcount_t: underflow; use-after-free. [ 110.908620] WARNING: CPU: 0 PID: 1866 at lib/refcount.c:87 refcount_dec_not_one+0xb8/0xc0 [ 110.908664] Modules linked in: rfcomm snd_seq_dummy snd_hrtimer snd_seq snd_seq_device cmac algif_hash aes_arm64 aes_generic algif_skcipher af_alg bnep hid_logitech_hidpp vc4 brcmfmac hci_uart btbcm brcmutil bluetooth snd_soc_hdmi_codec cfg80211 cec drm_display_helper drm_dma_helper drm_kms_helper snd_soc_core snd_compress snd_pcm_dmaengine fb_sys_fops sysimgblt syscopyarea sysfillrect raspberrypi_hwmon ecdh_generic ecc rfkill libaes i2c_bcm2835 binfmt_misc joydev snd_bcm2835(C) bcm2835_codec(C) bcm2835_isp(C) v4l2_mem2mem videobuf2_dma_contig snd_pcm bcm2835_v4l2(C) raspberrypi_gpiomem bcm2835_mmal_vchiq(C) videobuf2_v4l2 snd_timer videobuf2_vmalloc videobuf2_memops videobuf2_common snd videodev vc_sm_cma(C) mc hid_logitech_dj uio_pdrv_genirq uio i2c_dev drm fuse dm_mod drm_panel_orientation_quirks backlight ip_tables x_tables ipv6 [ 110.909086] CPU: 0 PID: 1866 Comm: kodi.bin Tainted: G C 6.1.66-v8+ #32 [ 110.909104] Hardware name: Raspberry Pi 3 Model B Rev 1.2 (DT) [ 110.909114] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 110.909132] pc : refcount_dec_not_one+0xb8/0xc0 [ 110.909152] lr : refcount_dec_not_one+0xb4/0xc0 [ 110.909170] sp : ffffffc00913b9c0 [ 110.909177] x29: ffffffc00913b9c0 x28: 000000556969bbb0 x27: 000000556990df60 [ 110.909205] x26: 0000000000000002 x25: 0000000000000004 x24: ffffff8004448480 [ 110.909230] x23: ffffff800570b500 x22: ffffff802e03a7bc x21: ffffffecfca68c78 [ 110.909257] x20: ffffff8002b42000 x19: ffffff802e03a600 x18: 0000000000000000 [ 110.909283] x17: 0000000000000011 x16: ffffffffffffffff x15: 0000000000000004 [ 110.909308] x14: 0000000000000fff x13: ffffffed577e47e0 x12: 0000000000000003 [ 110.909333] x11: 0000000000000000 x10: 0000000000000027 x9 : c912d0d083728c00 [ 110.909359] x8 : c912d0d083728c00 x7 : 65646e75203a745f x6 : 746e756f63666572 [ 110.909384] x5 : ffffffed579f62ee x4 : ffffffed579eb01e x3 : 0000000000000000 [ 110.909409] x2 : 0000000000000000 x1 : ffffffc00913b750 x0 : 0000000000000001 [ 110.909434] Call trace: [ 110.909441] refcount_dec_not_one+0xb8/0xc0 [ 110.909461] vc4_bo_dec_usecnt+0x4c/0x1b0 [vc4] [ 110.909903] vc4_cleanup_fb+0x44/0x50 [vc4] [ 110.910315] drm_atomic_helper_cleanup_planes+0x88/0xa4 [drm_kms_helper] [ 110.910669] vc4_atomic_commit_tail+0x390/0x9dc [vc4] [ 110.911079] commit_tail+0xb0/0x164 [drm_kms_helper] [ 110.911397] drm_atomic_helper_commit+0x1d0/0x1f0 [drm_kms_helper] [ 110.911716] drm_atomic_commit+0xb0/0xdc [drm] [ 110.912569] drm_mode_atomic_ioctl+0x348/0x4b8 [drm] [ 110.913330] drm_ioctl_kernel+0xec/0x15c [drm] [ 110.914091] drm_ioctl+0x24c/0x3b0 [drm] [ 110.914850] __arm64_sys_ioctl+0x9c/0xd4 [ 110.914873] invoke_syscall+0x4c/0x114 [ 110.914897] el0_svc_common+0xd0/0x118 [ 110.914917] do_el0_svc+0x38/0xd0 [ 110.914936] el0_svc+0x30/0x8c [ 110.914958] el0t_64_sync_handler+0x84/0xf0 [ 110.914979] el0t_64_sync+0x18c/0x190 [ 110.914996] ---[ end trace 0000000000000000 ]--- This happens because, although `prepare_fb` and `cleanup_fb` are perfectly balanced, we cannot guarantee consistency in the check plane->state->fb == state->fb. This means that sometimes we can increase the refcount in `prepare_fb` and don't decrease it in `cleanup_fb`. The opposite can also be true. In fact, the struct drm_plane .state shouldn't be accessed directly but instead, the `drm_atomic_get_new_plane_state()` helper function should be used. So, we could stick to this check, but using `drm_atomic_get_new_plane_state()`. But actually, this check is not re ---truncated---

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Disassociate vcpus from redistributor region on teardown When tearing down a redistributor region, make sure we don't have any dangling pointer to that region stored in a vcpu.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix uninititialized value in 'ext4_evict_inode' Syzbot found the following issue: ===================================================== BUG: KMSAN: uninit-value in ext4_evict_inode+0xdd/0x26b0 fs/ext4/inode.c:180 ext4_evict_inode+0xdd/0x26b0 fs/ext4/inode.c:180 evict+0x365/0x9a0 fs/inode.c:664 iput_final fs/inode.c:1747 [inline] iput+0x985/0xdd0 fs/inode.c:1773 __ext4_new_inode+0xe54/0x7ec0 fs/ext4/ialloc.c:1361 ext4_mknod+0x376/0x840 fs/ext4/namei.c:2844 vfs_mknod+0x79d/0x830 fs/namei.c:3914 do_mknodat+0x47d/0xaa0 __do_sys_mknodat fs/namei.c:3992 [inline] __se_sys_mknodat fs/namei.c:3989 [inline] __ia32_sys_mknodat+0xeb/0x150 fs/namei.c:3989 do_syscall_32_irqs_on arch/x86/entry/common.c:112 [inline] __do_fast_syscall_32+0xa2/0x100 arch/x86/entry/common.c:178 do_fast_syscall_32+0x33/0x70 arch/x86/entry/common.c:203 do_SYSENTER_32+0x1b/0x20 arch/x86/entry/common.c:246 entry_SYSENTER_compat_after_hwframe+0x70/0x82 Uninit was created at: __alloc_pages+0x9f1/0xe80 mm/page_alloc.c:5578 alloc_pages+0xaae/0xd80 mm/mempolicy.c:2285 alloc_slab_page mm/slub.c:1794 [inline] allocate_slab+0x1b5/0x1010 mm/slub.c:1939 new_slab mm/slub.c:1992 [inline] ___slab_alloc+0x10c3/0x2d60 mm/slub.c:3180 __slab_alloc mm/slub.c:3279 [inline] slab_alloc_node mm/slub.c:3364 [inline] slab_alloc mm/slub.c:3406 [inline] __kmem_cache_alloc_lru mm/slub.c:3413 [inline] kmem_cache_alloc_lru+0x6f3/0xb30 mm/slub.c:3429 alloc_inode_sb include/linux/fs.h:3117 [inline] ext4_alloc_inode+0x5f/0x860 fs/ext4/super.c:1321 alloc_inode+0x83/0x440 fs/inode.c:259 new_inode_pseudo fs/inode.c:1018 [inline] new_inode+0x3b/0x430 fs/inode.c:1046 __ext4_new_inode+0x2a7/0x7ec0 fs/ext4/ialloc.c:959 ext4_mkdir+0x4d5/0x1560 fs/ext4/namei.c:2992 vfs_mkdir+0x62a/0x870 fs/namei.c:4035 do_mkdirat+0x466/0x7b0 fs/namei.c:4060 __do_sys_mkdirat fs/namei.c:4075 [inline] __se_sys_mkdirat fs/namei.c:4073 [inline] __ia32_sys_mkdirat+0xc4/0x120 fs/namei.c:4073 do_syscall_32_irqs_on arch/x86/entry/common.c:112 [inline] __do_fast_syscall_32+0xa2/0x100 arch/x86/entry/common.c:178 do_fast_syscall_32+0x33/0x70 arch/x86/entry/common.c:203 do_SYSENTER_32+0x1b/0x20 arch/x86/entry/common.c:246 entry_SYSENTER_compat_after_hwframe+0x70/0x82 CPU: 1 PID: 4625 Comm: syz-executor.2 Not tainted 6.1.0-rc4-syzkaller-62821-gcb231e2f67ec #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022 ===================================================== Now, 'ext4_alloc_inode()' didn't init 'ei->i_flags'. If new inode failed before set 'ei->i_flags' in '__ext4_new_inode()', then do 'iput()'. As after 6bc0d63dad7f commit will access 'ei->i_flags' in 'ext4_evict_inode()' which will lead to access uninit-value. To solve above issue just init 'ei->i_flags' in 'ext4_alloc_inode()'.

In the Linux kernel, the following vulnerability has been resolved: net: bridge: mst: fix suspicious rcu usage in br_mst_set_state I converted br_mst_set_state to RCU to avoid a vlan use-after-free but forgot to change the vlan group dereference helper. Switch to vlan group RCU deref helper to fix the suspicious rcu usage warning.

containerd is an open-source container runtime. A bug was found in containerd prior to versions 1.6.38, 1.7.27, and 2.0.4 where containers launched with a User set as a `UID:GID` larger than the maximum 32-bit signed integer can cause an overflow condition where the container ultimately runs as root (UID 0). This could cause unexpected behavior for environments that require containers to run as a non-root user. This bug has been fixed in containerd 1.6.38, 1.7.27, and 2.04. As a workaround, ensure that only trusted images are used and that only trusted users have permissions to import images.

In the Linux kernel, the following vulnerability has been resolved: dmaengine: idxd: Fix possible Use-After-Free in irq_process_work_list Use list_for_each_entry_safe() to allow iterating through the list and deleting the entry in the iteration process. The descriptor is freed via idxd_desc_complete() and there's a slight chance may cause issue for the list iterator when the descriptor is reused by another thread without it being deleted from the list.

In the Linux kernel, the following vulnerability has been resolved: tcp/dccp: Don't use timer_pending() in reqsk_queue_unlink(). Martin KaFai Lau reported use-after-free [0] in reqsk_timer_handler(). """ We are seeing a use-after-free from a bpf prog attached to trace_tcp_retransmit_synack. The program passes the req->sk to the bpf_sk_storage_get_tracing kernel helper which does check for null before using it. """ The commit 83fccfc3940c ("inet: fix potential deadlock in reqsk_queue_unlink()") added timer_pending() in reqsk_queue_unlink() not to call del_timer_sync() from reqsk_timer_handler(), but it introduced a small race window. Before the timer is called, expire_timers() calls detach_timer(timer, true) to clear timer->entry.pprev and marks it as not pending. If reqsk_queue_unlink() checks timer_pending() just after expire_timers() calls detach_timer(), TCP will miss del_timer_sync(); the reqsk timer will continue running and send multiple SYN+ACKs until it expires. The reported UAF could happen if req->sk is close()d earlier than the timer expiration, which is 63s by default. The scenario would be 1. inet_csk_complete_hashdance() calls inet_csk_reqsk_queue_drop(), but del_timer_sync() is missed 2. reqsk timer is executed and scheduled again 3. req->sk is accept()ed and reqsk_put() decrements rsk_refcnt, but reqsk timer still has another one, and inet_csk_accept() does not clear req->sk for non-TFO sockets 4. sk is close()d 5. reqsk timer is executed again, and BPF touches req->sk Let's not use timer_pending() by passing the caller context to __inet_csk_reqsk_queue_drop(). Note that reqsk timer is pinned, so the issue does not happen in most use cases. [1] [0] BUG: KFENCE: use-after-free read in bpf_sk_storage_get_tracing+0x2e/0x1b0 Use-after-free read at 0x00000000a891fb3a (in kfence-#1): bpf_sk_storage_get_tracing+0x2e/0x1b0 bpf_prog_5ea3e95db6da0438_tcp_retransmit_synack+0x1d20/0x1dda bpf_trace_run2+0x4c/0xc0 tcp_rtx_synack+0xf9/0x100 reqsk_timer_handler+0xda/0x3d0 run_timer_softirq+0x292/0x8a0 irq_exit_rcu+0xf5/0x320 sysvec_apic_timer_interrupt+0x6d/0x80 asm_sysvec_apic_timer_interrupt+0x16/0x20 intel_idle_irq+0x5a/0xa0 cpuidle_enter_state+0x94/0x273 cpu_startup_entry+0x15e/0x260 start_secondary+0x8a/0x90 secondary_startup_64_no_verify+0xfa/0xfb kfence-#1: 0x00000000a72cc7b6-0x00000000d97616d9, size=2376, cache=TCPv6 allocated by task 0 on cpu 9 at 260507.901592s: sk_prot_alloc+0x35/0x140 sk_clone_lock+0x1f/0x3f0 inet_csk_clone_lock+0x15/0x160 tcp_create_openreq_child+0x1f/0x410 tcp_v6_syn_recv_sock+0x1da/0x700 tcp_check_req+0x1fb/0x510 tcp_v6_rcv+0x98b/0x1420 ipv6_list_rcv+0x2258/0x26e0 napi_complete_done+0x5b1/0x2990 mlx5e_napi_poll+0x2ae/0x8d0 net_rx_action+0x13e/0x590 irq_exit_rcu+0xf5/0x320 common_interrupt+0x80/0x90 asm_common_interrupt+0x22/0x40 cpuidle_enter_state+0xfb/0x273 cpu_startup_entry+0x15e/0x260 start_secondary+0x8a/0x90 secondary_startup_64_no_verify+0xfa/0xfb freed by task 0 on cpu 9 at 260507.927527s: rcu_core_si+0x4ff/0xf10 irq_exit_rcu+0xf5/0x320 sysvec_apic_timer_interrupt+0x6d/0x80 asm_sysvec_apic_timer_interrupt+0x16/0x20 cpuidle_enter_state+0xfb/0x273 cpu_startup_entry+0x15e/0x260 start_secondary+0x8a/0x90 secondary_startup_64_no_verify+0xfa/0xfb

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix OOBs when building SMB2_IOCTL request When using encryption, either enforced by the server or when using 'seal' mount option, the client will squash all compound request buffers down for encryption into a single iov in smb2_set_next_command(). SMB2_ioctl_init() allocates a small buffer (448 bytes) to hold the SMB2_IOCTL request in the first iov, and if the user passes an input buffer that is greater than 328 bytes, smb2_set_next_command() will end up writing off the end of @rqst->iov[0].iov_base as shown below: mount.cifs //srv/share /mnt -o ...,seal ln -s $(perl -e "print('a')for 1..1024") /mnt/link BUG: KASAN: slab-out-of-bounds in smb2_set_next_command.cold+0x1d6/0x24c [cifs] Write of size 4116 at addr ffff8881148fcab8 by task ln/859 CPU: 1 UID: 0 PID: 859 Comm: ln Not tainted 6.12.0-rc3 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x5d/0x80 ? smb2_set_next_command.cold+0x1d6/0x24c [cifs] print_report+0x156/0x4d9 ? smb2_set_next_command.cold+0x1d6/0x24c [cifs] ? __virt_addr_valid+0x145/0x310 ? __phys_addr+0x46/0x90 ? smb2_set_next_command.cold+0x1d6/0x24c [cifs] kasan_report+0xda/0x110 ? smb2_set_next_command.cold+0x1d6/0x24c [cifs] kasan_check_range+0x10f/0x1f0 __asan_memcpy+0x3c/0x60 smb2_set_next_command.cold+0x1d6/0x24c [cifs] smb2_compound_op+0x238c/0x3840 [cifs] ? kasan_save_track+0x14/0x30 ? kasan_save_free_info+0x3b/0x70 ? vfs_symlink+0x1a1/0x2c0 ? do_symlinkat+0x108/0x1c0 ? __pfx_smb2_compound_op+0x10/0x10 [cifs] ? kmem_cache_free+0x118/0x3e0 ? cifs_get_writable_path+0xeb/0x1a0 [cifs] smb2_get_reparse_inode+0x423/0x540 [cifs] ? __pfx_smb2_get_reparse_inode+0x10/0x10 [cifs] ? rcu_is_watching+0x20/0x50 ? __kmalloc_noprof+0x37c/0x480 ? smb2_create_reparse_symlink+0x257/0x490 [cifs] ? smb2_create_reparse_symlink+0x38f/0x490 [cifs] smb2_create_reparse_symlink+0x38f/0x490 [cifs] ? __pfx_smb2_create_reparse_symlink+0x10/0x10 [cifs] ? find_held_lock+0x8a/0xa0 ? hlock_class+0x32/0xb0 ? __build_path_from_dentry_optional_prefix+0x19d/0x2e0 [cifs] cifs_symlink+0x24f/0x960 [cifs] ? __pfx_make_vfsuid+0x10/0x10 ? __pfx_cifs_symlink+0x10/0x10 [cifs] ? make_vfsgid+0x6b/0xc0 ? generic_permission+0x96/0x2d0 vfs_symlink+0x1a1/0x2c0 do_symlinkat+0x108/0x1c0 ? __pfx_do_symlinkat+0x10/0x10 ? strncpy_from_user+0xaa/0x160 __x64_sys_symlinkat+0xb9/0xf0 do_syscall_64+0xbb/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f08d75c13bb

A use-after-free flaw was found in the Linux kernel's netfilter in the way a user triggers the nft_pipapo_remove function with the element, without a NFT_SET_EXT_KEY_END. This issue could allow a local user to crash the system or potentially escalate their privileges on the system.

In the Linux kernel, the following vulnerability has been resolved: ALSA: asihpi: Fix potential OOB array access ASIHPI driver stores some values in the static array upon a response from the driver, and its index depends on the firmware. We shouldn't trust it blindly. This patch adds a sanity check of the array index to fit in the array size.

In the Linux kernel, the following vulnerability has been resolved: bpf: Avoid splat in pskb_pull_reason syzkaller builds (CONFIG_DEBUG_NET=y) frequently trigger a debug hint in pskb_may_pull. We'd like to retain this debug check because it might hint at integer overflows and other issues (kernel code should pull headers, not huge value). In bpf case, this splat isn't interesting at all: such (nonsensical) bpf programs are typically generated by a fuzzer anyway. Do what Eric suggested and suppress such warning. For CONFIG_DEBUG_NET=n we don't need the extra check because pskb_may_pull will do the right thing: return an error without the WARN() backtrace.

In the Linux kernel, the following vulnerability has been resolved: jfs: xattr: fix buffer overflow for invalid xattr When an xattr size is not what is expected, it is printed out to the kernel log in hex format as a form of debugging. But when that xattr size is bigger than the expected size, printing it out can cause an access off the end of the buffer. Fix this all up by properly restricting the size of the debug hex dump in the kernel log.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix a potential use-after-free in bpf_link_free() After commit 1a80dbcb2dba, bpf_link can be freed by link->ops->dealloc_deferred, but the code still tests and uses link->ops->dealloc afterward, which leads to a use-after-free as reported by syzbot. Actually, one of them should be sufficient, so just call one of them instead of both. Also add a WARN_ON() in case of any problematic implementation.

In the Linux kernel, the following vulnerability has been resolved: ax25: fix incorrect dev_tracker usage While investigating a separate rose issue [1], and enabling CONFIG_NET_DEV_REFCNT_TRACKER=y, Bernard reported an orthogonal ax25 issue [2] An ax25_dev can be used by one (or many) struct ax25_cb. We thus need different dev_tracker, one per struct ax25_cb. After this patch is applied, we are able to focus on rose. [1] https://lore.kernel.org/netdev/fb7544a1-f42e-9254-18cc-c9b071f4ca70@free.fr/ [2] [ 205.798723] reference already released. [ 205.798732] allocated in: [ 205.798734] ax25_bind+0x1a2/0x230 [ax25] [ 205.798747] __sys_bind+0xea/0x110 [ 205.798753] __x64_sys_bind+0x18/0x20 [ 205.798758] do_syscall_64+0x5c/0x80 [ 205.798763] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 205.798768] freed in: [ 205.798770] ax25_release+0x115/0x370 [ax25] [ 205.798778] __sock_release+0x42/0xb0 [ 205.798782] sock_close+0x15/0x20 [ 205.798785] __fput+0x9f/0x260 [ 205.798789] ____fput+0xe/0x10 [ 205.798792] task_work_run+0x64/0xa0 [ 205.798798] exit_to_user_mode_prepare+0x18b/0x190 [ 205.798804] syscall_exit_to_user_mode+0x26/0x40 [ 205.798808] do_syscall_64+0x69/0x80 [ 205.798812] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 205.798827] ------------[ cut here ]------------ [ 205.798829] WARNING: CPU: 2 PID: 2605 at lib/ref_tracker.c:136 ref_tracker_free.cold+0x60/0x81 [ 205.798837] Modules linked in: rose netrom mkiss ax25 rfcomm cmac algif_hash algif_skcipher af_alg bnep snd_hda_codec_hdmi nls_iso8859_1 i915 rtw88_8821ce rtw88_8821c x86_pkg_temp_thermal rtw88_pci intel_powerclamp rtw88_core snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio coretemp snd_hda_intel kvm_intel snd_intel_dspcfg mac80211 snd_hda_codec kvm i2c_algo_bit drm_buddy drm_dp_helper btusb drm_kms_helper snd_hwdep btrtl snd_hda_core btbcm joydev crct10dif_pclmul btintel crc32_pclmul ghash_clmulni_intel mei_hdcp btmtk intel_rapl_msr aesni_intel bluetooth input_leds snd_pcm crypto_simd syscopyarea processor_thermal_device_pci_legacy sysfillrect cryptd intel_soc_dts_iosf snd_seq sysimgblt ecdh_generic fb_sys_fops rapl libarc4 processor_thermal_device intel_cstate processor_thermal_rfim cec snd_timer ecc snd_seq_device cfg80211 processor_thermal_mbox mei_me processor_thermal_rapl mei rc_core at24 snd intel_pch_thermal intel_rapl_common ttm soundcore int340x_thermal_zone video [ 205.798948] mac_hid acpi_pad sch_fq_codel ipmi_devintf ipmi_msghandler drm msr parport_pc ppdev lp parport ramoops pstore_blk reed_solomon pstore_zone efi_pstore ip_tables x_tables autofs4 hid_generic usbhid hid i2c_i801 i2c_smbus r8169 xhci_pci ahci libahci realtek lpc_ich xhci_pci_renesas [last unloaded: ax25] [ 205.798992] CPU: 2 PID: 2605 Comm: ax25ipd Not tainted 5.18.11-F6BVP #3 [ 205.798996] Hardware name: To be filled by O.E.M. To be filled by O.E.M./CK3, BIOS 5.011 09/16/2020 [ 205.798999] RIP: 0010:ref_tracker_free.cold+0x60/0x81 [ 205.799005] Code: e8 d2 01 9b ff 83 7b 18 00 74 14 48 c7 c7 2f d7 ff 98 e8 10 6e fc ff 8b 7b 18 e8 b8 01 9b ff 4c 89 ee 4c 89 e7 e8 5d fd 07 00 <0f> 0b b8 ea ff ff ff e9 30 05 9b ff 41 0f b6 f7 48 c7 c7 a0 fa 4e [ 205.799008] RSP: 0018:ffffaf5281073958 EFLAGS: 00010286 [ 205.799011] RAX: 0000000080000000 RBX: ffff9a0bd687ebe0 RCX: 0000000000000000 [ 205.799014] RDX: 0000000000000001 RSI: 0000000000000282 RDI: 00000000ffffffff [ 205.799016] RBP: ffffaf5281073a10 R08: 0000000000000003 R09: fffffffffffd5618 [ 205.799019] R10: 0000000000ffff10 R11: 000000000000000f R12: ffff9a0bc53384d0 [ 205.799022] R13: 0000000000000282 R14: 00000000ae000001 R15: 0000000000000001 [ 205.799024] FS: 0000000000000000(0000) GS:ffff9a0d0f300000(0000) knlGS:0000000000000000 [ 205.799028] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 205.799031] CR2: 00007ff6b8311554 CR3: 000000001ac10004 CR4: 00000000001706e0 [ 205.799033] Call Trace: [ 205.799035] <TASK> [ 205.799038] ? ax25_dev_device_down+0xd9/ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net: do not leave a dangling sk pointer, when socket creation fails It is possible to trigger a use-after-free by: * attaching an fentry probe to __sock_release() and the probe calling the bpf_get_socket_cookie() helper * running traceroute -I 1.1.1.1 on a freshly booted VM A KASAN enabled kernel will log something like below (decoded and stripped): ================================================================== BUG: KASAN: slab-use-after-free in __sock_gen_cookie (./arch/x86/include/asm/atomic64_64.h:15 ./include/linux/atomic/atomic-arch-fallback.h:2583 ./include/linux/atomic/atomic-instrumented.h:1611 net/core/sock_diag.c:29) Read of size 8 at addr ffff888007110dd8 by task traceroute/299 CPU: 2 PID: 299 Comm: traceroute Tainted: G E 6.10.0-rc2+ #2 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/01/2014 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:117 (discriminator 1)) print_report (mm/kasan/report.c:378 mm/kasan/report.c:488) ? __sock_gen_cookie (./arch/x86/include/asm/atomic64_64.h:15 ./include/linux/atomic/atomic-arch-fallback.h:2583 ./include/linux/atomic/atomic-instrumented.h:1611 net/core/sock_diag.c:29) kasan_report (mm/kasan/report.c:603) ? __sock_gen_cookie (./arch/x86/include/asm/atomic64_64.h:15 ./include/linux/atomic/atomic-arch-fallback.h:2583 ./include/linux/atomic/atomic-instrumented.h:1611 net/core/sock_diag.c:29) kasan_check_range (mm/kasan/generic.c:183 mm/kasan/generic.c:189) __sock_gen_cookie (./arch/x86/include/asm/atomic64_64.h:15 ./include/linux/atomic/atomic-arch-fallback.h:2583 ./include/linux/atomic/atomic-instrumented.h:1611 net/core/sock_diag.c:29) bpf_get_socket_ptr_cookie (./arch/x86/include/asm/preempt.h:94 ./include/linux/sock_diag.h:42 net/core/filter.c:5094 net/core/filter.c:5092) bpf_prog_875642cf11f1d139___sock_release+0x6e/0x8e bpf_trampoline_6442506592+0x47/0xaf __sock_release (net/socket.c:652) __sock_create (net/socket.c:1601) ... Allocated by task 299 on cpu 2 at 78.328492s: kasan_save_stack (mm/kasan/common.c:48) kasan_save_track (mm/kasan/common.c:68) __kasan_slab_alloc (mm/kasan/common.c:312 mm/kasan/common.c:338) kmem_cache_alloc_noprof (mm/slub.c:3941 mm/slub.c:4000 mm/slub.c:4007) sk_prot_alloc (net/core/sock.c:2075) sk_alloc (net/core/sock.c:2134) inet_create (net/ipv4/af_inet.c:327 net/ipv4/af_inet.c:252) __sock_create (net/socket.c:1572) __sys_socket (net/socket.c:1660 net/socket.c:1644 net/socket.c:1706) __x64_sys_socket (net/socket.c:1718) do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) Freed by task 299 on cpu 2 at 78.328502s: kasan_save_stack (mm/kasan/common.c:48) kasan_save_track (mm/kasan/common.c:68) kasan_save_free_info (mm/kasan/generic.c:582) poison_slab_object (mm/kasan/common.c:242) __kasan_slab_free (mm/kasan/common.c:256) kmem_cache_free (mm/slub.c:4437 mm/slub.c:4511) __sk_destruct (net/core/sock.c:2117 net/core/sock.c:2208) inet_create (net/ipv4/af_inet.c:397 net/ipv4/af_inet.c:252) __sock_create (net/socket.c:1572) __sys_socket (net/socket.c:1660 net/socket.c:1644 net/socket.c:1706) __x64_sys_socket (net/socket.c:1718) do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) Fix this by clearing the struct socket reference in sk_common_release() to cover all protocol families create functions, which may already attached the reference to the sk object with sock_init_data().

In the Linux kernel, the following vulnerability has been resolved: firmware: cs_dsp: Fix overflow checking of wmfw header Fix the checking that firmware file buffer is large enough for the wmfw header, to prevent overrunning the buffer. The original code tested that the firmware data buffer contained enough bytes for the sums of the size of the structs wmfw_header + wmfw_adsp1_sizes + wmfw_footer But wmfw_adsp1_sizes is only used on ADSP1 firmware. For ADSP2 and Halo Core the equivalent struct is wmfw_adsp2_sizes, which is 4 bytes longer. So the length check didn't guarantee that there are enough bytes in the firmware buffer for a header with wmfw_adsp2_sizes. This patch splits the length check into three separate parts. Each of the wmfw_header, wmfw_adsp?_sizes and wmfw_footer are checked separately before they are used.