In the Linux kernel, the following vulnerability has been resolved: io_uring: fix ltout double free on completion race Always remove linked timeout on io_link_timeout_fn() from the master request link list, otherwise we may get use-after-free when first io_link_timeout_fn() puts linked timeout in the fail path, and then will be found and put on master's free.

In the Linux kernel, the following vulnerability has been resolved: habanalabs/gaudi: Fix a potential use after free in gaudi_memset_device_memory Our code analyzer reported a uaf. In gaudi_memset_device_memory, cb is get via hl_cb_kernel_create() with 2 refcount. If hl_cs_allocate_job() failed, the execution runs into release_cb branch. One ref of cb is dropped by hl_cb_put(cb) and could be freed if other thread also drops one ref. Then cb is used by cb->id later, which is a potential uaf. My patch add a variable 'id' to accept the value of cb->id before the hl_cb_put(cb) is called, to avoid the potential uaf.

In the Linux kernel, the following vulnerability has been resolved: sctp: do asoc update earlier in sctp_sf_do_dupcook_a There's a panic that occurs in a few of envs, the call trace is as below: [] general protection fault, ... 0x29acd70f1000a: 0000 [#1] SMP PTI [] RIP: 0010:sctp_ulpevent_notify_peer_addr_change+0x4b/0x1fa [sctp] [] sctp_assoc_control_transport+0x1b9/0x210 [sctp] [] sctp_do_8_2_transport_strike.isra.16+0x15c/0x220 [sctp] [] sctp_cmd_interpreter.isra.21+0x1231/0x1a10 [sctp] [] sctp_do_sm+0xc3/0x2a0 [sctp] [] sctp_generate_timeout_event+0x81/0xf0 [sctp] This is caused by a transport use-after-free issue. When processing a duplicate COOKIE-ECHO chunk in sctp_sf_do_dupcook_a(), both COOKIE-ACK and SHUTDOWN chunks are allocated with the transort from the new asoc. However, later in the sideeffect machine, the old asoc is used to send them out and old asoc's shutdown_last_sent_to is set to the transport that SHUTDOWN chunk attached to in sctp_cmd_setup_t2(), which actually belongs to the new asoc. After the new_asoc is freed and the old asoc T2 timeout, the old asoc's shutdown_last_sent_to that is already freed would be accessed in sctp_sf_t2_timer_expire(). Thanks Alexander and Jere for helping dig into this issue. To fix it, this patch is to do the asoc update first, then allocate the COOKIE-ACK and SHUTDOWN chunks with the 'updated' old asoc. This would make more sense, as a chunk from an asoc shouldn't be sent out with another asoc. We had fixed quite a few issues caused by this.

In the Linux kernel, the following vulnerability has been resolved: net: usb: fix possible use-after-free in smsc75xx_bind The commit 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind") fails to clean up the work scheduled in smsc75xx_reset-> smsc75xx_set_multicast, which leads to use-after-free if the work is scheduled to start after the deallocation. In addition, this patch also removes a dangling pointer - dev->data[0]. This patch calls cancel_work_sync to cancel the scheduled work and set the dangling pointer to NULL.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: fix use-after-free in nft_set_catchall_destroy() We need to use list_for_each_entry_safe() iterator because we can not access @catchall after kfree_rcu() call. syzbot reported: BUG: KASAN: use-after-free in nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline] BUG: KASAN: use-after-free in nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline] BUG: KASAN: use-after-free in nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493 Read of size 8 at addr ffff8880716e5b80 by task syz-executor.3/8871 CPU: 1 PID: 8871 Comm: syz-executor.3 Not tainted 5.16.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_address_description.constprop.0.cold+0x8d/0x2ed mm/kasan/report.c:247 __kasan_report mm/kasan/report.c:433 [inline] kasan_report.cold+0x83/0xdf mm/kasan/report.c:450 nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline] nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline] nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493 __nft_release_table+0x79f/0xcd0 net/netfilter/nf_tables_api.c:9626 nft_rcv_nl_event+0x4f8/0x670 net/netfilter/nf_tables_api.c:9688 notifier_call_chain+0xb5/0x200 kernel/notifier.c:83 blocking_notifier_call_chain kernel/notifier.c:318 [inline] blocking_notifier_call_chain+0x67/0x90 kernel/notifier.c:306 netlink_release+0xcb6/0x1dd0 net/netlink/af_netlink.c:788 __sock_release+0xcd/0x280 net/socket.c:649 sock_close+0x18/0x20 net/socket.c:1314 __fput+0x286/0x9f0 fs/file_table.c:280 task_work_run+0xdd/0x1a0 kernel/task_work.c:164 tracehook_notify_resume include/linux/tracehook.h:189 [inline] exit_to_user_mode_loop kernel/entry/common.c:175 [inline] exit_to_user_mode_prepare+0x27e/0x290 kernel/entry/common.c:207 __syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline] syscall_exit_to_user_mode+0x19/0x60 kernel/entry/common.c:300 do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f75fbf28adb Code: 0f 05 48 3d 00 f0 ff ff 77 45 c3 0f 1f 40 00 48 83 ec 18 89 7c 24 0c e8 63 fc ff ff 8b 7c 24 0c 41 89 c0 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 35 44 89 c7 89 44 24 0c e8 a1 fc ff ff 8b 44 RSP: 002b:00007ffd8da7ec10 EFLAGS: 00000293 ORIG_RAX: 0000000000000003 RAX: 0000000000000000 RBX: 0000000000000004 RCX: 00007f75fbf28adb RDX: 00007f75fc08e828 RSI: ffffffffffffffff RDI: 0000000000000003 RBP: 00007f75fc08a960 R08: 0000000000000000 R09: 00007f75fc08e830 R10: 00007ffd8da7ed10 R11: 0000000000000293 R12: 00000000002067c3 R13: 00007ffd8da7ed10 R14: 00007f75fc088f60 R15: 0000000000000032 </TASK> Allocated by task 8886: kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38 kasan_set_track mm/kasan/common.c:46 [inline] set_alloc_info mm/kasan/common.c:434 [inline] ____kasan_kmalloc mm/kasan/common.c:513 [inline] ____kasan_kmalloc mm/kasan/common.c:472 [inline] __kasan_kmalloc+0xa6/0xd0 mm/kasan/common.c:522 kasan_kmalloc include/linux/kasan.h:269 [inline] kmem_cache_alloc_trace+0x1ea/0x4a0 mm/slab.c:3575 kmalloc include/linux/slab.h:590 [inline] nft_setelem_catchall_insert net/netfilter/nf_tables_api.c:5544 [inline] nft_setelem_insert net/netfilter/nf_tables_api.c:5562 [inline] nft_add_set_elem+0x232e/0x2f40 net/netfilter/nf_tables_api.c:5936 nf_tables_newsetelem+0x6ff/0xbb0 net/netfilter/nf_tables_api.c:6032 nfnetlink_rcv_batch+0x1710/0x25f0 net/netfilter/nfnetlink.c:513 nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline] nfnetlink_rcv+0x3af/0x420 net/netfilter/nfnetlink.c:652 netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline] netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1345 netlink_sendmsg+0x904/0xdf0 net/netlink/af_netlink.c:1921 sock_sendmsg_nosec net/ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: RDMA/rtrs-clt: destroy sysfs after removing session from active list A session can be removed dynamically by sysfs interface "remove_path" that eventually calls rtrs_clt_remove_path_from_sysfs function. The current rtrs_clt_remove_path_from_sysfs first removes the sysfs interfaces and frees sess->stats object. Second it removes the session from the active list. Therefore some functions could access non-connected session and access the freed sess->stats object even-if they check the session status before accessing the session. For instance rtrs_clt_request and get_next_path_min_inflight check the session status and try to send IO to the session. The session status could be changed when they are trying to send IO but they could not catch the change and update the statistics information in sess->stats object, and generate use-after-free problem. (see: "RDMA/rtrs-clt: Check state of the rtrs_clt_sess before reading its stats") This patch changes the rtrs_clt_remove_path_from_sysfs to remove the session from the active session list and then destroy the sysfs interfaces. Each function still should check the session status because closing or error recovery paths can change the status.

In the Linux kernel, the following vulnerability has been resolved: regmap: set debugfs_name to NULL after it is freed There is a upstream commit cffa4b2122f5("regmap:debugfs: Fix a memory leak when calling regmap_attach_dev") that adds a if condition when create name for debugfs_name. With below function invoking logical, debugfs_name is freed in regmap_debugfs_exit(), but it is not created again because of the if condition introduced by above commit. regmap_reinit_cache() regmap_debugfs_exit() ... regmap_debugfs_init() So, set debugfs_name to NULL after it is freed.

In the Linux kernel, the following vulnerability has been resolved: ethernet:enic: Fix a use after free bug in enic_hard_start_xmit In enic_hard_start_xmit, it calls enic_queue_wq_skb(). Inside enic_queue_wq_skb, if some error happens, the skb will be freed by dev_kfree_skb(skb). But the freed skb is still used in skb_tx_timestamp(skb). My patch makes enic_queue_wq_skb() return error and goto spin_unlock() incase of error. The solution is provided by Govind. See https://lkml.org/lkml/2021/4/30/961.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix use-after-free of encap entry in neigh update handler Function mlx5e_rep_neigh_update() wasn't updated to accommodate rtnl lock removal from TC filter update path and properly handle concurrent encap entry insertion/deletion which can lead to following use-after-free: [23827.464923] ================================================================== [23827.469446] BUG: KASAN: use-after-free in mlx5e_encap_take+0x72/0x140 [mlx5_core] [23827.470971] Read of size 4 at addr ffff8881d132228c by task kworker/u20:6/21635 [23827.472251] [23827.472615] CPU: 9 PID: 21635 Comm: kworker/u20:6 Not tainted 5.13.0-rc3+ #5 [23827.473788] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [23827.475639] Workqueue: mlx5e mlx5e_rep_neigh_update [mlx5_core] [23827.476731] Call Trace: [23827.477260] dump_stack+0xbb/0x107 [23827.477906] print_address_description.constprop.0+0x18/0x140 [23827.478896] ? mlx5e_encap_take+0x72/0x140 [mlx5_core] [23827.479879] ? mlx5e_encap_take+0x72/0x140 [mlx5_core] [23827.480905] kasan_report.cold+0x7c/0xd8 [23827.481701] ? mlx5e_encap_take+0x72/0x140 [mlx5_core] [23827.482744] kasan_check_range+0x145/0x1a0 [23827.493112] mlx5e_encap_take+0x72/0x140 [mlx5_core] [23827.494054] ? mlx5e_tc_tun_encap_info_equal_generic+0x140/0x140 [mlx5_core] [23827.495296] mlx5e_rep_neigh_update+0x41e/0x5e0 [mlx5_core] [23827.496338] ? mlx5e_rep_neigh_entry_release+0xb80/0xb80 [mlx5_core] [23827.497486] ? read_word_at_a_time+0xe/0x20 [23827.498250] ? strscpy+0xa0/0x2a0 [23827.498889] process_one_work+0x8ac/0x14e0 [23827.499638] ? lockdep_hardirqs_on_prepare+0x400/0x400 [23827.500537] ? pwq_dec_nr_in_flight+0x2c0/0x2c0 [23827.501359] ? rwlock_bug.part.0+0x90/0x90 [23827.502116] worker_thread+0x53b/0x1220 [23827.502831] ? process_one_work+0x14e0/0x14e0 [23827.503627] kthread+0x328/0x3f0 [23827.504254] ? _raw_spin_unlock_irq+0x24/0x40 [23827.505065] ? __kthread_bind_mask+0x90/0x90 [23827.505912] ret_from_fork+0x1f/0x30 [23827.506621] [23827.506987] Allocated by task 28248: [23827.507694] kasan_save_stack+0x1b/0x40 [23827.508476] __kasan_kmalloc+0x7c/0x90 [23827.509197] mlx5e_attach_encap+0xde1/0x1d40 [mlx5_core] [23827.510194] mlx5e_tc_add_fdb_flow+0x397/0xc40 [mlx5_core] [23827.511218] __mlx5e_add_fdb_flow+0x519/0xb30 [mlx5_core] [23827.512234] mlx5e_configure_flower+0x191c/0x4870 [mlx5_core] [23827.513298] tc_setup_cb_add+0x1d5/0x420 [23827.514023] fl_hw_replace_filter+0x382/0x6a0 [cls_flower] [23827.514975] fl_change+0x2ceb/0x4a51 [cls_flower] [23827.515821] tc_new_tfilter+0x89a/0x2070 [23827.516548] rtnetlink_rcv_msg+0x644/0x8c0 [23827.517300] netlink_rcv_skb+0x11d/0x340 [23827.518021] netlink_unicast+0x42b/0x700 [23827.518742] netlink_sendmsg+0x743/0xc20 [23827.519467] sock_sendmsg+0xb2/0xe0 [23827.520131] ____sys_sendmsg+0x590/0x770 [23827.520851] ___sys_sendmsg+0xd8/0x160 [23827.521552] __sys_sendmsg+0xb7/0x140 [23827.522238] do_syscall_64+0x3a/0x70 [23827.522907] entry_SYSCALL_64_after_hwframe+0x44/0xae [23827.523797] [23827.524163] Freed by task 25948: [23827.524780] kasan_save_stack+0x1b/0x40 [23827.525488] kasan_set_track+0x1c/0x30 [23827.526187] kasan_set_free_info+0x20/0x30 [23827.526968] __kasan_slab_free+0xed/0x130 [23827.527709] slab_free_freelist_hook+0xcf/0x1d0 [23827.528528] kmem_cache_free_bulk+0x33a/0x6e0 [23827.529317] kfree_rcu_work+0x55f/0xb70 [23827.530024] process_one_work+0x8ac/0x14e0 [23827.530770] worker_thread+0x53b/0x1220 [23827.531480] kthread+0x328/0x3f0 [23827.532114] ret_from_fork+0x1f/0x30 [23827.532785] [23827.533147] Last potentially related work creation: [23827.534007] kasan_save_stack+0x1b/0x40 [23827.534710] kasan_record_aux_stack+0xab/0xc0 [23827.535492] kvfree_call_rcu+0x31/0x7b0 [23827.536206] mlx5e_tc_del ---truncated---

In the Linux kernel, the following vulnerability has been resolved: spi: Fix use-after-free with devm_spi_alloc_* We can't rely on the contents of the devres list during spi_unregister_controller(), as the list is already torn down at the time we perform devres_find() for devm_spi_release_controller. This causes devices registered with devm_spi_alloc_{master,slave}() to be mistakenly identified as legacy, non-devm managed devices and have their reference counters decremented below 0. ------------[ cut here ]------------ WARNING: CPU: 1 PID: 660 at lib/refcount.c:28 refcount_warn_saturate+0x108/0x174 [<b0396f04>] (refcount_warn_saturate) from [<b03c56a4>] (kobject_put+0x90/0x98) [<b03c5614>] (kobject_put) from [<b0447b4c>] (put_device+0x20/0x24) r4:b6700140 [<b0447b2c>] (put_device) from [<b07515e8>] (devm_spi_release_controller+0x3c/0x40) [<b07515ac>] (devm_spi_release_controller) from [<b045343c>] (release_nodes+0x84/0xc4) r5:b6700180 r4:b6700100 [<b04533b8>] (release_nodes) from [<b0454160>] (devres_release_all+0x5c/0x60) r8:b1638c54 r7:b117ad94 r6:b1638c10 r5:b117ad94 r4:b163dc10 [<b0454104>] (devres_release_all) from [<b044e41c>] (__device_release_driver+0x144/0x1ec) r5:b117ad94 r4:b163dc10 [<b044e2d8>] (__device_release_driver) from [<b044f70c>] (device_driver_detach+0x84/0xa0) r9:00000000 r8:00000000 r7:b117ad94 r6:b163dc54 r5:b1638c10 r4:b163dc10 [<b044f688>] (device_driver_detach) from [<b044d274>] (unbind_store+0xe4/0xf8) Instead, determine the devm allocation state as a flag on the controller which is guaranteed to be stable during cleanup.

In the Linux kernel, the following vulnerability has been resolved: xen-netback: take a reference to the RX task thread Do this in order to prevent the task from being freed if the thread returns (which can be triggered by the frontend) before the call to kthread_stop done as part of the backend tear down. Not taking the reference will lead to a use-after-free in that scenario. Such reference was taken before but dropped as part of the rework done in 2ac061ce97f4. Reintroduce the reference taking and add a comment this time explaining why it's needed. This is XSA-374 / CVE-2021-28691.

In the Linux kernel, the following vulnerability has been resolved: net:emac/emac-mac: Fix a use after free in emac_mac_tx_buf_send In emac_mac_tx_buf_send, it calls emac_tx_fill_tpd(..,skb,..). If some error happens in emac_tx_fill_tpd(), the skb will be freed via dev_kfree_skb(skb) in error branch of emac_tx_fill_tpd(). But the freed skb is still used via skb->len by netdev_sent_queue(,skb->len). As i observed that emac_tx_fill_tpd() haven't modified the value of skb->len, thus my patch assigns skb->len to 'len' before the possible free and use 'len' instead of skb->len later.

In the Linux kernel, the following vulnerability has been resolved: ACPI: custom_method: fix potential use-after-free issue In cm_write(), buf is always freed when reaching the end of the function. If the requested count is less than table.length, the allocated buffer will be freed but subsequent calls to cm_write() will still try to access it. Remove the unconditional kfree(buf) at the end of the function and set the buf to NULL in the -EINVAL error path to match the rest of function.

In the Linux kernel, the following vulnerability has been resolved: net: dpaa2-eth: fix use-after-free in dpaa2_eth_remove Access to netdev after free_netdev() will cause use-after-free bug. Move debug log before free_netdev() call to avoid it.

In the Linux kernel, the following vulnerability has been resolved: usb: typec: tcpm: fix use-after-free case in tcpm_register_source_caps There could be a potential use-after-free case in tcpm_register_source_caps(). This could happen when: * new (say invalid) source caps are advertised * the existing source caps are unregistered * tcpm_register_source_caps() returns with an error as usb_power_delivery_register_capabilities() fails This causes port->partner_source_caps to hold on to the now freed source caps. Reset port->partner_source_caps value to NULL after unregistering existing source caps.

In the Linux kernel, the following vulnerability has been resolved: drm/prime: Fix use after free in mmap with drm_gem_ttm_mmap drm_gem_ttm_mmap() drops a reference to the gem object on success. If the gem object's refcount == 1 on entry to drm_gem_prime_mmap(), that drop will free the gem object, and the subsequent drm_gem_object_get() will be a UAF. Fix by grabbing a reference before calling the mmap helper. This issue was forseen when the reference dropping was adding in commit 9786b65bc61ac ("drm/ttm: fix mmap refcounting"): "For that to work properly the drm_gem_object_get() call in drm_gem_ttm_mmap() must be moved so it happens before calling obj->funcs->mmap(), otherwise the gem refcount would go down to zero."

In the Linux kernel, the following vulnerability has been resolved: i40e: Fix use-after-free in i40e_client_subtask() Currently the call to i40e_client_del_instance frees the object pf->cinst, however pf->cinst->lan_info is being accessed after the free. Fix this by adding the missing return. Addresses-Coverity: ("Read from pointer after free")

In the Linux kernel, the following vulnerability has been resolved: KVM: Destroy I/O bus devices on unregister failure _after_ sync'ing SRCU If allocating a new instance of an I/O bus fails when unregistering a device, wait to destroy the device until after all readers are guaranteed to see the new null bus. Destroying devices before the bus is nullified could lead to use-after-free since readers expect the devices on their reference of the bus to remain valid.

In the Linux kernel, the following vulnerability has been resolved: net/tls: Fix use-after-free after the TLS device goes down and up When a netdev with active TLS offload goes down, tls_device_down is called to stop the offload and tear down the TLS context. However, the socket stays alive, and it still points to the TLS context, which is now deallocated. If a netdev goes up, while the connection is still active, and the data flow resumes after a number of TCP retransmissions, it will lead to a use-after-free of the TLS context. This commit addresses this bug by keeping the context alive until its normal destruction, and implements the necessary fallbacks, so that the connection can resume in software (non-offloaded) kTLS mode. On the TX side tls_sw_fallback is used to encrypt all packets. The RX side already has all the necessary fallbacks, because receiving non-decrypted packets is supported. The thing needed on the RX side is to block resync requests, which are normally produced after receiving non-decrypted packets. The necessary synchronization is implemented for a graceful teardown: first the fallbacks are deployed, then the driver resources are released (it used to be possible to have a tls_dev_resync after tls_dev_del). A new flag called TLS_RX_DEV_DEGRADED is added to indicate the fallback mode. It's used to skip the RX resync logic completely, as it becomes useless, and some objects may be released (for example, resync_async, which is allocated and freed by the driver).

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix use-after-free in lpfc_unreg_rpi() routine An error is detected with the following report when unloading the driver: "KASAN: use-after-free in lpfc_unreg_rpi+0x1b1b" The NLP_REG_LOGIN_SEND nlp_flag is set in lpfc_reg_fab_ctrl_node(), but the flag is not cleared upon completion of the login. This allows a second call to lpfc_unreg_rpi() to proceed with nlp_rpi set to LPFC_RPI_ALLOW_ERROR. This results in a use after free access when used as an rpi_ids array index. Fix by clearing the NLP_REG_LOGIN_SEND nlp_flag in lpfc_mbx_cmpl_fc_reg_login().

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: core: Fix invalid error returning in mhi_queue mhi_queue returns an error when the doorbell is not accessible in the current state. This can happen when the device is in non M0 state, like M3, and needs to be waken-up prior ringing the DB. This case is managed earlier by triggering an asynchronous M3 exit via controller resume/suspend callbacks, that in turn will cause M0 transition and DB update. So, since it's not an error but just delaying of doorbell update, there is no reason to return an error. This also fixes a use after free error for skb case, indeed a caller queuing skb will try to free the skb if the queueing fails, but in that case queueing has been done.

In the Linux kernel, the following vulnerability has been resolved: net/nfc: fix use-after-free llcp_sock_bind/connect Commits 8a4cd82d ("nfc: fix refcount leak in llcp_sock_connect()") and c33b1cc62 ("nfc: fix refcount leak in llcp_sock_bind()") fixed a refcount leak bug in bind/connect but introduced a use-after-free if the same local is assigned to 2 different sockets. This can be triggered by the following simple program: int sock1 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP ); int sock2 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP ); memset( &addr, 0, sizeof(struct sockaddr_nfc_llcp) ); addr.sa_family = AF_NFC; addr.nfc_protocol = NFC_PROTO_NFC_DEP; bind( sock1, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) ) bind( sock2, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) ) close(sock1); close(sock2); Fix this by assigning NULL to llcp_sock->local after calling nfc_llcp_local_put. This addresses CVE-2021-23134.

In the Linux kernel, the following vulnerability has been resolved: net: wwan: iosm: Fix tainted pointer delete is case of region creation fail In case of region creation fail in ipc_devlink_create_region(), previously created regions delete process starts from tainted pointer which actually holds error code value. Fix this bug by decreasing region index before delete. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: spi: spi-zynqmp-gqspi: fix use-after-free in zynqmp_qspi_exec_op When handling op->addr, it is using the buffer "tmpbuf" which has been freed. This will trigger a use-after-free KASAN warning. Let's use temporary variables to store op->addr.val and op->cmd.opcode to fix this issue.

The do_get_mempolicy function in mm/mempolicy.c in the Linux kernel before 4.12.9 allows local users to cause a denial of service (use-after-free) or possibly have unspecified other impact via crafted system calls.

In the Linux kernel, the following vulnerability has been resolved: gfs2: Fix use-after-free in gfs2_glock_shrink_scan The GLF_LRU flag is checked under lru_lock in gfs2_glock_remove_from_lru() to remove the glock from the lru list in __gfs2_glock_put(). On the shrink scan path, the same flag is cleared under lru_lock but because of cond_resched_lock(&lru_lock) in gfs2_dispose_glock_lru(), progress on the put side can be made without deleting the glock from the lru list. Keep GLF_LRU across the race window opened by cond_resched_lock(&lru_lock) to ensure correct behavior on both sides - clear GLF_LRU after list_del under lru_lock.

In the Linux kernel, the following vulnerability has been resolved: inet: fully convert sk->sk_rx_dst to RCU rules syzbot reported various issues around early demux, one being included in this changelog [1] sk->sk_rx_dst is using RCU protection without clearly documenting it. And following sequences in tcp_v4_do_rcv()/tcp_v6_do_rcv() are not following standard RCU rules. [a] dst_release(dst); [b] sk->sk_rx_dst = NULL; They look wrong because a delete operation of RCU protected pointer is supposed to clear the pointer before the call_rcu()/synchronize_rcu() guarding actual memory freeing. In some cases indeed, dst could be freed before [b] is done. We could cheat by clearing sk_rx_dst before calling dst_release(), but this seems the right time to stick to standard RCU annotations and debugging facilities. [1] BUG: KASAN: use-after-free in dst_check include/net/dst.h:470 [inline] BUG: KASAN: use-after-free in tcp_v4_early_demux+0x95b/0x960 net/ipv4/tcp_ipv4.c:1792 Read of size 2 at addr ffff88807f1cb73a by task syz-executor.5/9204 CPU: 0 PID: 9204 Comm: syz-executor.5 Not tainted 5.16.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_address_description.constprop.0.cold+0x8d/0x320 mm/kasan/report.c:247 __kasan_report mm/kasan/report.c:433 [inline] kasan_report.cold+0x83/0xdf mm/kasan/report.c:450 dst_check include/net/dst.h:470 [inline] tcp_v4_early_demux+0x95b/0x960 net/ipv4/tcp_ipv4.c:1792 ip_rcv_finish_core.constprop.0+0x15de/0x1e80 net/ipv4/ip_input.c:340 ip_list_rcv_finish.constprop.0+0x1b2/0x6e0 net/ipv4/ip_input.c:583 ip_sublist_rcv net/ipv4/ip_input.c:609 [inline] ip_list_rcv+0x34e/0x490 net/ipv4/ip_input.c:644 __netif_receive_skb_list_ptype net/core/dev.c:5508 [inline] __netif_receive_skb_list_core+0x549/0x8e0 net/core/dev.c:5556 __netif_receive_skb_list net/core/dev.c:5608 [inline] netif_receive_skb_list_internal+0x75e/0xd80 net/core/dev.c:5699 gro_normal_list net/core/dev.c:5853 [inline] gro_normal_list net/core/dev.c:5849 [inline] napi_complete_done+0x1f1/0x880 net/core/dev.c:6590 virtqueue_napi_complete drivers/net/virtio_net.c:339 [inline] virtnet_poll+0xca2/0x11b0 drivers/net/virtio_net.c:1557 __napi_poll+0xaf/0x440 net/core/dev.c:7023 napi_poll net/core/dev.c:7090 [inline] net_rx_action+0x801/0xb40 net/core/dev.c:7177 __do_softirq+0x29b/0x9c2 kernel/softirq.c:558 invoke_softirq kernel/softirq.c:432 [inline] __irq_exit_rcu+0x123/0x180 kernel/softirq.c:637 irq_exit_rcu+0x5/0x20 kernel/softirq.c:649 common_interrupt+0x52/0xc0 arch/x86/kernel/irq.c:240 asm_common_interrupt+0x1e/0x40 arch/x86/include/asm/idtentry.h:629 RIP: 0033:0x7f5e972bfd57 Code: 39 d1 73 14 0f 1f 80 00 00 00 00 48 8b 50 f8 48 83 e8 08 48 39 ca 77 f3 48 39 c3 73 3e 48 89 13 48 8b 50 f8 48 89 38 49 8b 0e <48> 8b 3e 48 83 c3 08 48 83 c6 08 eb bc 48 39 d1 72 9e 48 39 d0 73 RSP: 002b:00007fff8a413210 EFLAGS: 00000283 RAX: 00007f5e97108990 RBX: 00007f5e97108338 RCX: ffffffff81d3aa45 RDX: ffffffff81d3aa45 RSI: 00007f5e97108340 RDI: ffffffff81d3aa45 RBP: 00007f5e97107eb8 R08: 00007f5e97108d88 R09: 0000000093c2e8d9 R10: 0000000000000000 R11: 0000000000000000 R12: 00007f5e97107eb0 R13: 00007f5e97108338 R14: 00007f5e97107ea8 R15: 0000000000000019 </TASK> Allocated by task 13: kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38 kasan_set_track mm/kasan/common.c:46 [inline] set_alloc_info mm/kasan/common.c:434 [inline] __kasan_slab_alloc+0x90/0xc0 mm/kasan/common.c:467 kasan_slab_alloc include/linux/kasan.h:259 [inline] slab_post_alloc_hook mm/slab.h:519 [inline] slab_alloc_node mm/slub.c:3234 [inline] slab_alloc mm/slub.c:3242 [inline] kmem_cache_alloc+0x202/0x3a0 mm/slub.c:3247 dst_alloc+0x146/0x1f0 net/core/dst.c:92 rt_dst_alloc+0x73/0x430 net/ipv4/route.c:1613 ip_route_input_slow+0x1817/0x3a20 net/ipv4/route.c:234 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: Drivers: hv: vmbus: Use after free in __vmbus_open() The "open_info" variable is added to the &vmbus_connection.chn_msg_list, but the error handling frees "open_info" without removing it from the list. This will result in a use after free. First remove it from the list, and then free it.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: cyclic allocation of msg_id to avoid reuse Reusing the msg_id after a maliciously completed reopen request may cause a read request to remain unprocessed and result in a hung, as shown below: t1 | t2 | t3 ------------------------------------------------- cachefiles_ondemand_select_req cachefiles_ondemand_object_is_close(A) cachefiles_ondemand_set_object_reopening(A) queue_work(fscache_object_wq, &info->work) ondemand_object_worker cachefiles_ondemand_init_object(A) cachefiles_ondemand_send_req(OPEN) // get msg_id 6 wait_for_completion(&req_A->done) cachefiles_ondemand_daemon_read // read msg_id 6 req_A cachefiles_ondemand_get_fd copy_to_user // Malicious completion msg_id 6 copen 6,-1 cachefiles_ondemand_copen complete(&req_A->done) // will not set the object to close // because ondemand_id && fd is valid. // ondemand_object_worker() is done // but the object is still reopening. // new open req_B cachefiles_ondemand_init_object(B) cachefiles_ondemand_send_req(OPEN) // reuse msg_id 6 process_open_req copen 6,A.size // The expected failed copen was executed successfully Expect copen to fail, and when it does, it closes fd, which sets the object to close, and then close triggers reopen again. However, due to msg_id reuse resulting in a successful copen, the anonymous fd is not closed until the daemon exits. Therefore read requests waiting for reopen to complete may trigger hung task. To avoid this issue, allocate the msg_id cyclically to avoid reusing the msg_id for a very short duration of time.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: fix potential use-after-free in ec_bhf_remove static void ec_bhf_remove(struct pci_dev *dev) { ... struct ec_bhf_priv *priv = netdev_priv(net_dev); unregister_netdev(net_dev); free_netdev(net_dev); pci_iounmap(dev, priv->dma_io); pci_iounmap(dev, priv->io); ... } priv is netdev private data, but it is used after free_netdev(). It can cause use-after-free when accessing priv pointer. So, fix it by moving free_netdev() after pci_iounmap() calls.

In the Linux kernel, the following vulnerability has been resolved: net: bridge: fix vlan tunnel dst refcnt when egressing The egress tunnel code uses dst_clone() and directly sets the result which is wrong because the entry might have 0 refcnt or be already deleted, causing number of problems. It also triggers the WARN_ON() in dst_hold()[1] when a refcnt couldn't be taken. Fix it by using dst_hold_safe() and checking if a reference was actually taken before setting the dst. [1] dmesg WARN_ON log and following refcnt errors WARNING: CPU: 5 PID: 38 at include/net/dst.h:230 br_handle_egress_vlan_tunnel+0x10b/0x134 [bridge] Modules linked in: 8021q garp mrp bridge stp llc bonding ipv6 virtio_net CPU: 5 PID: 38 Comm: ksoftirqd/5 Kdump: loaded Tainted: G W 5.13.0-rc3+ #360 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014 RIP: 0010:br_handle_egress_vlan_tunnel+0x10b/0x134 [bridge] Code: e8 85 bc 01 e1 45 84 f6 74 90 45 31 f6 85 db 48 c7 c7 a0 02 19 a0 41 0f 94 c6 31 c9 31 d2 44 89 f6 e8 64 bc 01 e1 85 db 75 02 <0f> 0b 31 c9 31 d2 44 89 f6 48 c7 c7 70 02 19 a0 e8 4b bc 01 e1 49 RSP: 0018:ffff8881003d39e8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffffffa01902a0 RBP: ffff8881040c6700 R08: 0000000000000000 R09: 0000000000000001 R10: 2ce93d0054fe0d00 R11: 54fe0d00000e0000 R12: ffff888109515000 R13: 0000000000000000 R14: 0000000000000001 R15: 0000000000000401 FS: 0000000000000000(0000) GS:ffff88822bf40000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f42ba70f030 CR3: 0000000109926000 CR4: 00000000000006e0 Call Trace: br_handle_vlan+0xbc/0xca [bridge] __br_forward+0x23/0x164 [bridge] deliver_clone+0x41/0x48 [bridge] br_handle_frame_finish+0x36f/0x3aa [bridge] ? skb_dst+0x2e/0x38 [bridge] ? br_handle_ingress_vlan_tunnel+0x3e/0x1c8 [bridge] ? br_handle_frame_finish+0x3aa/0x3aa [bridge] br_handle_frame+0x2c3/0x377 [bridge] ? __skb_pull+0x33/0x51 ? vlan_do_receive+0x4f/0x36a ? br_handle_frame_finish+0x3aa/0x3aa [bridge] __netif_receive_skb_core+0x539/0x7c6 ? __list_del_entry_valid+0x16e/0x1c2 __netif_receive_skb_list_core+0x6d/0xd6 netif_receive_skb_list_internal+0x1d9/0x1fa gro_normal_list+0x22/0x3e dev_gro_receive+0x55b/0x600 ? detach_buf_split+0x58/0x140 napi_gro_receive+0x94/0x12e virtnet_poll+0x15d/0x315 [virtio_net] __napi_poll+0x2c/0x1c9 net_rx_action+0xe6/0x1fb __do_softirq+0x115/0x2d8 run_ksoftirqd+0x18/0x20 smpboot_thread_fn+0x183/0x19c ? smpboot_unregister_percpu_thread+0x66/0x66 kthread+0x10a/0x10f ? kthread_mod_delayed_work+0xb6/0xb6 ret_from_fork+0x22/0x30 ---[ end trace 49f61b07f775fd2b ]--- dst_release: dst:00000000c02d677a refcnt:-1 dst_release underflow

In the Linux kernel, the following vulnerability has been resolved: RDMA/siw: Fix a use after free in siw_alloc_mr Our code analyzer reported a UAF. In siw_alloc_mr(), it calls siw_mr_add_mem(mr,..). In the implementation of siw_mr_add_mem(), mem is assigned to mr->mem and then mem is freed via kfree(mem) if xa_alloc_cyclic() failed. Here, mr->mem still point to a freed object. After, the execution continue up to the err_out branch of siw_alloc_mr, and the freed mr->mem is used in siw_mr_drop_mem(mr). My patch moves "mr->mem = mem" behind the if (xa_alloc_cyclic(..)<0) {} section, to avoid the uaf.

In the Linux kernel, the following vulnerability has been resolved: ath10k: Fix a use after free in ath10k_htc_send_bundle In ath10k_htc_send_bundle, the bundle_skb could be freed by dev_kfree_skb_any(bundle_skb). But the bundle_skb is used later by bundle_skb->len. As skb_len = bundle_skb->len, my patch replaces bundle_skb->len to skb_len after the bundle_skb was freed.

A use-after-free vulnerability in the Linux kernel's net/sched: cls_route component can be exploited to achieve local privilege escalation. When route4_change() is called on an existing filter, the whole tcf_result struct is always copied into the new instance of the filter. This causes a problem when updating a filter bound to a class, as tcf_unbind_filter() is always called on the old instance in the success path, decreasing filter_cnt of the still referenced class and allowing it to be deleted, leading to a use-after-free. We recommend upgrading past commit b80b829e9e2c1b3f7aae34855e04d8f6ecaf13c8.

A flaw was found in the Linux kernel’s implementation of MIDI, where an attacker with a local account and the permissions to issue ioctl commands to midi devices could trigger a use-after-free issue. A write to this specific memory while freed and before use causes the flow of execution to change and possibly allow for memory corruption or privilege escalation. The highest threat from this vulnerability is to confidentiality, integrity, as well as system availability.

The dccp_disconnect function in net/dccp/proto.c in the Linux kernel through 4.14.3 allows local users to gain privileges or cause a denial of service (use-after-free) via an AF_UNSPEC connect system call during the DCCP_LISTEN state.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/vm: move xa_alloc to prevent UAF Evil user can guess the next id of the vm before the ioctl completes and then call vm destroy ioctl to trigger UAF since create ioctl is still referencing the same vm. Move the xa_alloc all the way to the end to prevent this. v2: - Rebase (cherry picked from commit dcfd3971327f3ee92765154baebbaece833d3ca9)

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: MGMT: Fix slab-use-after-free Read in mgmt_remove_adv_monitor_sync This fixes the following crash: ================================================================== BUG: KASAN: slab-use-after-free in mgmt_remove_adv_monitor_sync+0x3a/0xd0 net/bluetooth/mgmt.c:5543 Read of size 8 at addr ffff88814128f898 by task kworker/u9:4/5961 CPU: 1 UID: 0 PID: 5961 Comm: kworker/u9:4 Not tainted 6.12.0-syzkaller-10684-gf1cd565ce577 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0x169/0x550 mm/kasan/report.c:489 kasan_report+0x143/0x180 mm/kasan/report.c:602 mgmt_remove_adv_monitor_sync+0x3a/0xd0 net/bluetooth/mgmt.c:5543 hci_cmd_sync_work+0x22b/0x400 net/bluetooth/hci_sync.c:332 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0xa63/0x1850 kernel/workqueue.c:3310 worker_thread+0x870/0xd30 kernel/workqueue.c:3391 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 </TASK> Allocated by task 16026: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3f/0x80 mm/kasan/common.c:68 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0x98/0xb0 mm/kasan/common.c:394 kasan_kmalloc include/linux/kasan.h:260 [inline] __kmalloc_cache_noprof+0x243/0x390 mm/slub.c:4314 kmalloc_noprof include/linux/slab.h:901 [inline] kzalloc_noprof include/linux/slab.h:1037 [inline] mgmt_pending_new+0x65/0x250 net/bluetooth/mgmt_util.c:269 mgmt_pending_add+0x36/0x120 net/bluetooth/mgmt_util.c:296 remove_adv_monitor+0x102/0x1b0 net/bluetooth/mgmt.c:5568 hci_mgmt_cmd+0xc47/0x11d0 net/bluetooth/hci_sock.c:1712 hci_sock_sendmsg+0x7b8/0x11c0 net/bluetooth/hci_sock.c:1832 sock_sendmsg_nosec net/socket.c:711 [inline] __sock_sendmsg+0x221/0x270 net/socket.c:726 sock_write_iter+0x2d7/0x3f0 net/socket.c:1147 new_sync_write fs/read_write.c:586 [inline] vfs_write+0xaeb/0xd30 fs/read_write.c:679 ksys_write+0x18f/0x2b0 fs/read_write.c:731 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Freed by task 16022: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3f/0x80 mm/kasan/common.c:68 kasan_save_free_info+0x40/0x50 mm/kasan/generic.c:582 poison_slab_object mm/kasan/common.c:247 [inline] __kasan_slab_free+0x59/0x70 mm/kasan/common.c:264 kasan_slab_free include/linux/kasan.h:233 [inline] slab_free_hook mm/slub.c:2338 [inline] slab_free mm/slub.c:4598 [inline] kfree+0x196/0x420 mm/slub.c:4746 mgmt_pending_foreach+0xd1/0x130 net/bluetooth/mgmt_util.c:259 __mgmt_power_off+0x183/0x430 net/bluetooth/mgmt.c:9550 hci_dev_close_sync+0x6c4/0x11c0 net/bluetooth/hci_sync.c:5208 hci_dev_do_close net/bluetooth/hci_core.c:483 [inline] hci_dev_close+0x112/0x210 net/bluetooth/hci_core.c:508 sock_do_ioctl+0x158/0x460 net/socket.c:1209 sock_ioctl+0x626/0x8e0 net/socket.c:1328 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:906 [inline] __se_sys_ioctl+0xf5/0x170 fs/ioctl.c:892 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: KVM: Explicitly verify target vCPU is online in kvm_get_vcpu() Explicitly verify the target vCPU is fully online _prior_ to clamping the index in kvm_get_vcpu(). If the index is "bad", the nospec clamping will generate '0', i.e. KVM will return vCPU0 instead of NULL. In practice, the bug is unlikely to cause problems, as it will only come into play if userspace or the guest is buggy or misbehaving, e.g. KVM may send interrupts to vCPU0 instead of dropping them on the floor. However, returning vCPU0 when it shouldn't exist per online_vcpus is problematic now that KVM uses an xarray for the vCPUs array, as KVM needs to insert into the xarray before publishing the vCPU to userspace (see commit c5b077549136 ("KVM: Convert the kvm->vcpus array to a xarray")), i.e. before vCPU creation is guaranteed to succeed. As a result, incorrectly providing access to vCPU0 will trigger a use-after-free if vCPU0 is dereferenced and kvm_vm_ioctl_create_vcpu() bails out of vCPU creation due to an error and frees vCPU0. Commit afb2acb2e3a3 ("KVM: Fix vcpu_array[0] races") papered over that issue, but in doing so introduced an unsolvable teardown conundrum. Preventing accesses to vCPU0 before it's fully online will allow reverting commit afb2acb2e3a3, without re-introducing the vcpu_array[0] UAF race.

In the Linux kernel, the following vulnerability has been resolved: i3c: dw: Fix use-after-free in dw_i3c_master driver due to race condition In dw_i3c_common_probe, &master->hj_work is bound with dw_i3c_hj_work. And dw_i3c_master_irq_handler can call dw_i3c_master_irq_handle_ibis function to start the work. If we remove the module which will call dw_i3c_common_remove to make cleanup, it will free master->base through i3c_master_unregister while the work mentioned above will be used. The sequence of operations that may lead to a UAF bug is as follows: CPU0 CPU1 | dw_i3c_hj_work dw_i3c_common_remove | i3c_master_unregister(&master->base) | device_unregister(&master->dev) | device_release | //free master->base | | i3c_master_do_daa(&master->base) | //use master->base Fix it by ensuring that the work is canceled before proceeding with the cleanup in dw_i3c_common_remove.

In the Linux kernel, the following vulnerability has been resolved: wifi: rtlwifi: remove unused check_buddy_priv Commit 2461c7d60f9f ("rtlwifi: Update header file") introduced a global list of private data structures. Later on, commit 26634c4b1868 ("rtlwifi Modify existing bits to match vendor version 2013.02.07") started adding the private data to that list at probe time and added a hook, check_buddy_priv to find the private data from a similar device. However, that function was never used. Besides, though there is a lock for that list, it is never used. And when the probe fails, the private data is never removed from the list. This would cause a second probe to access freed memory. Remove the unused hook, structures and members, which will prevent the potential race condition on the list and its corruption during a second probe when probe fails.

In the Linux kernel, the following vulnerability has been resolved: RDMA/rxe: Remove the direct link to net_device The similar patch in siw is in the link: https://git.kernel.org/rdma/rdma/c/16b87037b48889 This problem also occurred in RXE. The following analyze this problem. In the following Call Traces: " BUG: KASAN: slab-use-after-free in dev_get_flags+0x188/0x1d0 net/core/dev.c:8782 Read of size 4 at addr ffff8880554640b0 by task kworker/1:4/5295 CPU: 1 UID: 0 PID: 5295 Comm: kworker/1:4 Not tainted 6.12.0-rc3-syzkaller-00399-g9197b73fd7bb #0 Hardware name: Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 Workqueue: infiniband ib_cache_event_task Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:377 [inline] print_report+0x169/0x550 mm/kasan/report.c:488 kasan_report+0x143/0x180 mm/kasan/report.c:601 dev_get_flags+0x188/0x1d0 net/core/dev.c:8782 rxe_query_port+0x12d/0x260 drivers/infiniband/sw/rxe/rxe_verbs.c:60 __ib_query_port drivers/infiniband/core/device.c:2111 [inline] ib_query_port+0x168/0x7d0 drivers/infiniband/core/device.c:2143 ib_cache_update+0x1a9/0xb80 drivers/infiniband/core/cache.c:1494 ib_cache_event_task+0xf3/0x1e0 drivers/infiniband/core/cache.c:1568 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0xa65/0x1850 kernel/workqueue.c:3310 worker_thread+0x870/0xd30 kernel/workqueue.c:3391 kthread+0x2f2/0x390 kernel/kthread.c:389 ret_from_fork+0x4d/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 </TASK> " 1). In the link [1], " infiniband syz2: set down " This means that on 839.350575, the event ib_cache_event_task was sent andi queued in ib_wq. 2). In the link [1], " team0 (unregistering): Port device team_slave_0 removed " It indicates that before 843.251853, the net device should be freed. 3). In the link [1], " BUG: KASAN: slab-use-after-free in dev_get_flags+0x188/0x1d0 " This means that on 850.559070, this slab-use-after-free problem occurred. In all, on 839.350575, the event ib_cache_event_task was sent and queued in ib_wq, before 843.251853, the net device veth was freed. on 850.559070, this event was executed, and the mentioned freed net device was called. Thus, the above call trace occurred. [1] https://syzkaller.appspot.com/x/log.txt?x=12e7025f980000

In the Linux kernel, the following vulnerability has been resolved: drm: adv7511: Fix use-after-free in adv7533_attach_dsi() The host_node pointer was assigned and freed in adv7533_parse_dt(), and later, adv7533_attach_dsi() uses the same. Fix this use-after-free issue by dropping of_node_put() in adv7533_parse_dt() and calling of_node_put() in error path of probe() and also in the remove().

In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Remove dangling pointers When an async control is written, we copy a pointer to the file handle that started the operation. That pointer will be used when the device is done. Which could be anytime in the future. If the user closes that file descriptor, its structure will be freed, and there will be one dangling pointer per pending async control, that the driver will try to use. Clean all the dangling pointers during release(). To avoid adding a performance penalty in the most common case (no async operation), a counter has been introduced with some logic to make sure that it is properly handled.

In the Linux kernel, the following vulnerability has been resolved: s390/cpum_sf: Handle CPU hotplug remove during sampling CPU hotplug remove handling triggers the following function call sequence: CPUHP_AP_PERF_S390_SF_ONLINE --> s390_pmu_sf_offline_cpu() ... CPUHP_AP_PERF_ONLINE --> perf_event_exit_cpu() The s390 CPUMF sampling CPU hotplug handler invokes: s390_pmu_sf_offline_cpu() +--> cpusf_pmu_setup() +--> setup_pmc_cpu() +--> deallocate_buffers() This function de-allocates all sampling data buffers (SDBs) allocated for that CPU at event initialization. It also clears the PMU_F_RESERVED bit. The CPU is gone and can not be sampled. With the event still being active on the removed CPU, the CPU event hotplug support in kernel performance subsystem triggers the following function calls on the removed CPU: perf_event_exit_cpu() +--> perf_event_exit_cpu_context() +--> __perf_event_exit_context() +--> __perf_remove_from_context() +--> event_sched_out() +--> cpumsf_pmu_del() +--> cpumsf_pmu_stop() +--> hw_perf_event_update() to stop and remove the event. During removal of the event, the sampling device driver tries to read out the remaining samples from the sample data buffers (SDBs). But they have already been freed (and may have been re-assigned). This may lead to a use after free situation in which case the samples are most likely invalid. In the best case the memory has not been reassigned and still contains valid data. Remedy this situation and check if the CPU is still in reserved state (bit PMU_F_RESERVED set). In this case the SDBs have not been released an contain valid data. This is always the case when the event is removed (and no CPU hotplug off occured). If the PMU_F_RESERVED bit is not set, the SDB buffers are gone.

In the Linux kernel, the following vulnerability has been resolved: PCI/ASPM: Fix link state exit during switch upstream function removal Before 456d8aa37d0f ("PCI/ASPM: Disable ASPM on MFD function removal to avoid use-after-free"), we would free the ASPM link only after the last function on the bus pertaining to the given link was removed. That was too late. If function 0 is removed before sibling function, link->downstream would point to free'd memory after. After above change, we freed the ASPM parent link state upon any function removal on the bus pertaining to a given link. That is too early. If the link is to a PCIe switch with MFD on the upstream port, then removing functions other than 0 first would free a link which still remains parent_link to the remaining downstream ports. The resulting GPFs are especially frequent during hot-unplug, because pciehp removes devices on the link bus in reverse order. On that switch, function 0 is the virtual P2P bridge to the internal bus. Free exactly when function 0 is removed -- before the parent link is obsolete, but after all subordinate links are gone. [kwilczynski: commit log]

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Skip restore TC rules for vport rep without loaded flag During driver unload, unregister_netdev is called after unloading vport rep. So, the mlx5e_rep_priv is already freed while trying to get rpriv->netdev, or walk rpriv->tc_ht, which results in use-after-free. So add the checking to make sure access the data of vport rep which is still loaded.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix read pointer after free in ath12k_mac_assign_vif_to_vdev() In ath12k_mac_assign_vif_to_vdev(), if arvif is created on a different radio, it gets deleted from that radio through a call to ath12k_mac_unassign_link_vif(). This action frees the arvif pointer. Subsequently, there is a check involving arvif, which will result in a read-after-free scenario. Fix this by moving this check after arvif is again assigned via call to ath12k_mac_assign_link_vif(). Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1

In the Linux kernel, the following vulnerability has been resolved: net/smc: fix LGR and link use-after-free issue We encountered a LGR/link use-after-free issue, which manifested as the LGR/link refcnt reaching 0 early and entering the clear process, making resource access unsafe. refcount_t: addition on 0; use-after-free. WARNING: CPU: 14 PID: 107447 at lib/refcount.c:25 refcount_warn_saturate+0x9c/0x140 Workqueue: events smc_lgr_terminate_work [smc] Call trace: refcount_warn_saturate+0x9c/0x140 __smc_lgr_terminate.part.45+0x2a8/0x370 [smc] smc_lgr_terminate_work+0x28/0x30 [smc] process_one_work+0x1b8/0x420 worker_thread+0x158/0x510 kthread+0x114/0x118 or refcount_t: underflow; use-after-free. WARNING: CPU: 6 PID: 93140 at lib/refcount.c:28 refcount_warn_saturate+0xf0/0x140 Workqueue: smc_hs_wq smc_listen_work [smc] Call trace: refcount_warn_saturate+0xf0/0x140 smcr_link_put+0x1cc/0x1d8 [smc] smc_conn_free+0x110/0x1b0 [smc] smc_conn_abort+0x50/0x60 [smc] smc_listen_find_device+0x75c/0x790 [smc] smc_listen_work+0x368/0x8a0 [smc] process_one_work+0x1b8/0x420 worker_thread+0x158/0x510 kthread+0x114/0x118 It is caused by repeated release of LGR/link refcnt. One suspect is that smc_conn_free() is called repeatedly because some smc_conn_free() from server listening path are not protected by sock lock. e.g. Calls under socklock | smc_listen_work ------------------------------------------------------- lock_sock(sk) | smc_conn_abort smc_conn_free | \- smc_conn_free \- smcr_link_put | \- smcr_link_put (duplicated) release_sock(sk) So here add sock lock protection in smc_listen_work() path, making it exclusive with other connection operations.

In the Linux kernel, the following vulnerability has been resolved: net: defer final 'struct net' free in netns dismantle Ilya reported a slab-use-after-free in dst_destroy [1] Issue is in xfrm6_net_init() and xfrm4_net_init() : They copy xfrm[46]_dst_ops_template into net->xfrm.xfrm[46]_dst_ops. But net structure might be freed before all the dst callbacks are called. So when dst_destroy() calls later : if (dst->ops->destroy) dst->ops->destroy(dst); dst->ops points to the old net->xfrm.xfrm[46]_dst_ops, which has been freed. See a relevant issue fixed in : ac888d58869b ("net: do not delay dst_entries_add() in dst_release()") A fix is to queue the 'struct net' to be freed after one another cleanup_net() round (and existing rcu_barrier()) [1] BUG: KASAN: slab-use-after-free in dst_destroy (net/core/dst.c:112) Read of size 8 at addr ffff8882137ccab0 by task swapper/37/0 Dec 03 05:46:18 kernel: CPU: 37 UID: 0 PID: 0 Comm: swapper/37 Kdump: loaded Not tainted 6.12.0 #67 Hardware name: Red Hat KVM/RHEL, BIOS 1.16.1-1.el9 04/01/2014 Call Trace: <IRQ> dump_stack_lvl (lib/dump_stack.c:124) print_address_description.constprop.0 (mm/kasan/report.c:378) ? dst_destroy (net/core/dst.c:112) print_report (mm/kasan/report.c:489) ? dst_destroy (net/core/dst.c:112) ? kasan_addr_to_slab (mm/kasan/common.c:37) kasan_report (mm/kasan/report.c:603) ? dst_destroy (net/core/dst.c:112) ? rcu_do_batch (kernel/rcu/tree.c:2567) dst_destroy (net/core/dst.c:112) rcu_do_batch (kernel/rcu/tree.c:2567) ? __pfx_rcu_do_batch (kernel/rcu/tree.c:2491) ? lockdep_hardirqs_on_prepare (kernel/locking/lockdep.c:4339 kernel/locking/lockdep.c:4406) rcu_core (kernel/rcu/tree.c:2825) handle_softirqs (kernel/softirq.c:554) __irq_exit_rcu (kernel/softirq.c:589 kernel/softirq.c:428 kernel/softirq.c:637) irq_exit_rcu (kernel/softirq.c:651) sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1049 arch/x86/kernel/apic/apic.c:1049) </IRQ> <TASK> asm_sysvec_apic_timer_interrupt (./arch/x86/include/asm/idtentry.h:702) RIP: 0010:default_idle (./arch/x86/include/asm/irqflags.h:37 ./arch/x86/include/asm/irqflags.h:92 arch/x86/kernel/process.c:743) Code: 00 4d 29 c8 4c 01 c7 4c 29 c2 e9 6e ff ff ff 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 66 90 0f 00 2d c7 c9 27 00 fb f4 <fa> c3 cc cc cc cc 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 90 RSP: 0018:ffff888100d2fe00 EFLAGS: 00000246 RAX: 00000000001870ed RBX: 1ffff110201a5fc2 RCX: ffffffffb61a3e46 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffffb3d4d123 RBP: 0000000000000000 R08: 0000000000000001 R09: ffffed11c7e1835d R10: ffff888e3f0c1aeb R11: 0000000000000000 R12: 0000000000000000 R13: ffff888100d20000 R14: dffffc0000000000 R15: 0000000000000000 ? ct_kernel_exit.constprop.0 (kernel/context_tracking.c:148) ? cpuidle_idle_call (kernel/sched/idle.c:186) default_idle_call (./include/linux/cpuidle.h:143 kernel/sched/idle.c:118) cpuidle_idle_call (kernel/sched/idle.c:186) ? __pfx_cpuidle_idle_call (kernel/sched/idle.c:168) ? lock_release (kernel/locking/lockdep.c:467 kernel/locking/lockdep.c:5848) ? lockdep_hardirqs_on_prepare (kernel/locking/lockdep.c:4347 kernel/locking/lockdep.c:4406) ? tsc_verify_tsc_adjust (arch/x86/kernel/tsc_sync.c:59) do_idle (kernel/sched/idle.c:326) cpu_startup_entry (kernel/sched/idle.c:423 (discriminator 1)) start_secondary (arch/x86/kernel/smpboot.c:202 arch/x86/kernel/smpboot.c:282) ? __pfx_start_secondary (arch/x86/kernel/smpboot.c:232) ? soft_restart_cpu (arch/x86/kernel/head_64.S:452) common_startup_64 (arch/x86/kernel/head_64.S:414) </TASK> Dec 03 05:46:18 kernel: Allocated by task 12184: kasan_save_stack (mm/kasan/common.c:48) kasan_save_track (./arch/x86/include/asm/current.h:49 mm/kasan/common.c:60 mm/kasan/common.c:69) __kasan_slab_alloc (mm/kasan/common.c:319 mm/kasan/common.c:345) kmem_cache_alloc_noprof (mm/slub.c:4085 mm/slub.c:4134 mm/slub.c:4141) copy_net_ns (net/core/net_namespace.c:421 net/core/net_namespace.c:480) create_new_namespaces ---truncated---