In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7921s: fix potential hung tasks during chip recovery During chip recovery (e.g. chip reset), there is a possible situation that kernel worker reset_work is holding the lock and waiting for kernel thread stat_worker to be parked, while stat_worker is waiting for the release of the same lock. It causes a deadlock resulting in the dumping of hung tasks messages and possible rebooting of the device. This patch prevents the execution of stat_worker during the chip recovery.

In the Linux kernel, the following vulnerability has been resolved: serial: imx: Introduce timeout when waiting on transmitter empty By waiting at most 1 second for USR2_TXDC to be set, we avoid a potential deadlock. In case of the timeout, there is not much we can do, so we simply ignore the transmitter state and optimistically try to continue.

In the Linux kernel, the following vulnerability has been resolved: ext4: do not create EA inode under buffer lock ext4_xattr_set_entry() creates new EA inodes while holding buffer lock on the external xattr block. This is problematic as it nests all the allocation locking (which acquires locks on other buffers) under the buffer lock. This can even deadlock when the filesystem is corrupted and e.g. quota file is setup to contain xattr block as data block. Move the allocation of EA inode out of ext4_xattr_set_entry() into the callers.

In the Linux kernel, the following vulnerability has been resolved: net: ks8851: Fix deadlock with the SPI chip variant When SMP is enabled and spinlocks are actually functional then there is a deadlock with the 'statelock' spinlock between ks8851_start_xmit_spi and ks8851_irq: watchdog: BUG: soft lockup - CPU#0 stuck for 27s! call trace: queued_spin_lock_slowpath+0x100/0x284 do_raw_spin_lock+0x34/0x44 ks8851_start_xmit_spi+0x30/0xb8 ks8851_start_xmit+0x14/0x20 netdev_start_xmit+0x40/0x6c dev_hard_start_xmit+0x6c/0xbc sch_direct_xmit+0xa4/0x22c __qdisc_run+0x138/0x3fc qdisc_run+0x24/0x3c net_tx_action+0xf8/0x130 handle_softirqs+0x1ac/0x1f0 __do_softirq+0x14/0x20 ____do_softirq+0x10/0x1c call_on_irq_stack+0x3c/0x58 do_softirq_own_stack+0x1c/0x28 __irq_exit_rcu+0x54/0x9c irq_exit_rcu+0x10/0x1c el1_interrupt+0x38/0x50 el1h_64_irq_handler+0x18/0x24 el1h_64_irq+0x64/0x68 __netif_schedule+0x6c/0x80 netif_tx_wake_queue+0x38/0x48 ks8851_irq+0xb8/0x2c8 irq_thread_fn+0x2c/0x74 irq_thread+0x10c/0x1b0 kthread+0xc8/0xd8 ret_from_fork+0x10/0x20 This issue has not been identified earlier because tests were done on a device with SMP disabled and so spinlocks were actually NOPs. Now use spin_(un)lock_bh for TX queue related locking to avoid execution of softirq work synchronously that would lead to a deadlock.

In the Linux kernel, the following vulnerability has been resolved: usb: cdnsp: Fix deadlock issue in cdnsp_thread_irq_handler Patch fixes the following critical issue caused by deadlock which has been detected during testing NCM class: smp: csd: Detected non-responsive CSD lock (#1) on CPU#0 smp: csd: CSD lock (#1) unresponsive. .... RIP: 0010:native_queued_spin_lock_slowpath+0x61/0x1d0 RSP: 0018:ffffbc494011cde0 EFLAGS: 00000002 RAX: 0000000000000101 RBX: ffff9ee8116b4a68 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9ee8116b4658 RBP: ffffbc494011cde0 R08: 0000000000000001 R09: 0000000000000000 R10: ffff9ee8116b4670 R11: 0000000000000000 R12: ffff9ee8116b4658 R13: ffff9ee8116b4670 R14: 0000000000000246 R15: ffff9ee8116b4658 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7bcc41a830 CR3: 000000007a612003 CR4: 00000000001706e0 Call Trace: <IRQ> do_raw_spin_lock+0xc0/0xd0 _raw_spin_lock_irqsave+0x95/0xa0 cdnsp_gadget_ep_queue.cold+0x88/0x107 [cdnsp_udc_pci] usb_ep_queue+0x35/0x110 eth_start_xmit+0x220/0x3d0 [u_ether] ncm_tx_timeout+0x34/0x40 [usb_f_ncm] ? ncm_free_inst+0x50/0x50 [usb_f_ncm] __hrtimer_run_queues+0xac/0x440 hrtimer_run_softirq+0x8c/0xb0 __do_softirq+0xcf/0x428 asm_call_irq_on_stack+0x12/0x20 </IRQ> do_softirq_own_stack+0x61/0x70 irq_exit_rcu+0xc1/0xd0 sysvec_apic_timer_interrupt+0x52/0xb0 asm_sysvec_apic_timer_interrupt+0x12/0x20 RIP: 0010:do_raw_spin_trylock+0x18/0x40 RSP: 0018:ffffbc494138bda8 EFLAGS: 00000246 RAX: 0000000000000000 RBX: ffff9ee8116b4658 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff9ee8116b4658 RBP: ffffbc494138bda8 R08: 0000000000000001 R09: 0000000000000000 R10: ffff9ee8116b4670 R11: 0000000000000000 R12: ffff9ee8116b4658 R13: ffff9ee8116b4670 R14: ffff9ee7b5c73d80 R15: ffff9ee8116b4000 _raw_spin_lock+0x3d/0x70 ? cdnsp_thread_irq_handler.cold+0x32/0x112c [cdnsp_udc_pci] cdnsp_thread_irq_handler.cold+0x32/0x112c [cdnsp_udc_pci] ? cdnsp_remove_request+0x1f0/0x1f0 [cdnsp_udc_pci] ? cdnsp_thread_irq_handler+0x5/0xa0 [cdnsp_udc_pci] ? irq_thread+0xa0/0x1c0 irq_thread_fn+0x28/0x60 irq_thread+0x105/0x1c0 ? __kthread_parkme+0x42/0x90 ? irq_forced_thread_fn+0x90/0x90 ? wake_threads_waitq+0x30/0x30 ? irq_thread_check_affinity+0xe0/0xe0 kthread+0x12a/0x160 ? kthread_park+0x90/0x90 ret_from_fork+0x22/0x30 The root cause of issue is spin_lock/spin_unlock instruction instead spin_lock_irqsave/spin_lock_irqrestore in cdnsp_thread_irq_handler function.

In the Linux kernel, the following vulnerability has been resolved: soc/tegra: regulators: Fix locking up when voltage-spread is out of range Fix voltage coupler lockup which happens when voltage-spread is out of range due to a bug in the code. The max-spread requirement shall be accounted when CPU regulator doesn't have consumers. This problem is observed on Tegra30 Ouya game console once system-wide DVFS is enabled in a device-tree.

In the Linux kernel, the following vulnerability has been resolved: i2c: lpi2c: Avoid calling clk_get_rate during transfer Instead of repeatedly calling clk_get_rate for each transfer, lock the clock rate and cache the value. A deadlock has been observed while adding tlv320aic32x4 audio codec to the system. When this clock provider adds its clock, the clk mutex is locked already, it needs to access i2c, which in return needs the mutex for clk_get_rate as well.

In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: core: remove lock of otg mode during gadget suspend/resume to avoid deadlock When config CONFIG_USB_DWC3_DUAL_ROLE is selected, and trigger system to enter suspend status with below command: echo mem > /sys/power/state There will be a deadlock issue occurring. Detailed invoking path as below: dwc3_suspend_common() spin_lock_irqsave(&dwc->lock, flags); <-- 1st dwc3_gadget_suspend(dwc); dwc3_gadget_soft_disconnect(dwc); spin_lock_irqsave(&dwc->lock, flags); <-- 2nd This issue is exposed by commit c7ebd8149ee5 ("usb: dwc3: gadget: Fix NULL pointer dereference in dwc3_gadget_suspend") that removes the code of checking whether dwc->gadget_driver is NULL or not. It causes the following code is executed and deadlock occurs when trying to get the spinlock. In fact, the root cause is the commit 5265397f9442("usb: dwc3: Remove DWC3 locking during gadget suspend/resume") that forgot to remove the lock of otg mode. So, remove the redundant lock of otg mode during gadget suspend/resume.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_core: cancel all works upon hci_unregister_dev() syzbot is reporting that calling hci_release_dev() from hci_error_reset() due to hci_dev_put() from hci_error_reset() can cause deadlock at destroy_workqueue(), for hci_error_reset() is called from hdev->req_workqueue which destroy_workqueue() needs to flush. We need to make sure that hdev->{rx_work,cmd_work,tx_work} which are queued into hdev->workqueue and hdev->{power_on,error_reset} which are queued into hdev->req_workqueue are no longer running by the moment destroy_workqueue(hdev->workqueue); destroy_workqueue(hdev->req_workqueue); are called from hci_release_dev(). Call cancel_work_sync() on these work items from hci_unregister_dev() as soon as hdev->list is removed from hci_dev_list.

In the Linux kernel, the following vulnerability has been resolved: pinctrl: fix deadlock in create_pinctrl() when handling -EPROBE_DEFER In create_pinctrl(), pinctrl_maps_mutex is acquired before calling add_setting(). If add_setting() returns -EPROBE_DEFER, create_pinctrl() calls pinctrl_free(). However, pinctrl_free() attempts to acquire pinctrl_maps_mutex, which is already held by create_pinctrl(), leading to a potential deadlock. This patch resolves the issue by releasing pinctrl_maps_mutex before calling pinctrl_free(), preventing the deadlock. This bug was discovered and resolved using Coverity Static Analysis Security Testing (SAST) by Synopsys, Inc.

In the Linux kernel, the following vulnerability has been resolved: riscv: kexec: Avoid deadlock in kexec crash path If the kexec crash code is called in the interrupt context, the machine_kexec_mask_interrupts() function will trigger a deadlock while trying to acquire the irqdesc spinlock and then deactivate irqchip in irq_set_irqchip_state() function. Unlike arm64, riscv only requires irq_eoi handler to complete EOI and keeping irq_set_irqchip_state() will only leave this possible deadlock without any use. So we simply remove it.

In the Linux kernel, the following vulnerability has been resolved: f2fs: don't set RO when shutting down f2fs Shutdown does not check the error of thaw_super due to readonly, which causes a deadlock like below. f2fs_ioc_shutdown(F2FS_GOING_DOWN_FULLSYNC) issue_discard_thread - bdev_freeze - freeze_super - f2fs_stop_checkpoint() - f2fs_handle_critical_error - sb_start_write - set RO - waiting - bdev_thaw - thaw_super_locked - return -EINVAL, if sb_rdonly() - f2fs_stop_discard_thread -> wait for kthread_stop(discard_thread);

In the Linux kernel, the following vulnerability has been resolved: IB/ipoib: Fix mcast list locking Releasing the `priv->lock` while iterating the `priv->multicast_list` in `ipoib_mcast_join_task()` opens a window for `ipoib_mcast_dev_flush()` to remove the items while in the middle of iteration. If the mcast is removed while the lock was dropped, the for loop spins forever resulting in a hard lockup (as was reported on RHEL 4.18.0-372.75.1.el8_6 kernel): Task A (kworker/u72:2 below) | Task B (kworker/u72:0 below) -----------------------------------+----------------------------------- ipoib_mcast_join_task(work) | ipoib_ib_dev_flush_light(work) spin_lock_irq(&priv->lock) | __ipoib_ib_dev_flush(priv, ...) list_for_each_entry(mcast, | ipoib_mcast_dev_flush(dev = priv->dev) &priv->multicast_list, list) | ipoib_mcast_join(dev, mcast) | spin_unlock_irq(&priv->lock) | | spin_lock_irqsave(&priv->lock, flags) | list_for_each_entry_safe(mcast, tmcast, | &priv->multicast_list, list) | list_del(&mcast->list); | list_add_tail(&mcast->list, &remove_list) | spin_unlock_irqrestore(&priv->lock, flags) spin_lock_irq(&priv->lock) | | ipoib_mcast_remove_list(&remove_list) (Here, `mcast` is no longer on the | list_for_each_entry_safe(mcast, tmcast, `priv->multicast_list` and we keep | remove_list, list) spinning on the `remove_list` of | >>> wait_for_completion(&mcast->done) the other thread which is blocked | and the list is still valid on | it's stack.) Fix this by keeping the lock held and changing to GFP_ATOMIC to prevent eventual sleeps. Unfortunately we could not reproduce the lockup and confirm this fix but based on the code review I think this fix should address such lockups. crash> bc 31 PID: 747 TASK: ff1c6a1a007e8000 CPU: 31 COMMAND: "kworker/u72:2" -- [exception RIP: ipoib_mcast_join_task+0x1b1] RIP: ffffffffc0944ac1 RSP: ff646f199a8c7e00 RFLAGS: 00000002 RAX: 0000000000000000 RBX: ff1c6a1a04dc82f8 RCX: 0000000000000000 work (&priv->mcast_task{,.work}) RDX: ff1c6a192d60ac68 RSI: 0000000000000286 RDI: ff1c6a1a04dc8000 &mcast->list RBP: ff646f199a8c7e90 R8: ff1c699980019420 R9: ff1c6a1920c9a000 R10: ff646f199a8c7e00 R11: ff1c6a191a7d9800 R12: ff1c6a192d60ac00 mcast R13: ff1c6a1d82200000 R14: ff1c6a1a04dc8000 R15: ff1c6a1a04dc82d8 dev priv (&priv->lock) &priv->multicast_list (aka head) ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 --- <NMI exception stack> --- #5 [ff646f199a8c7e00] ipoib_mcast_join_task+0x1b1 at ffffffffc0944ac1 [ib_ipoib] #6 [ff646f199a8c7e98] process_one_work+0x1a7 at ffffffff9bf10967 crash> rx ff646f199a8c7e68 ff646f199a8c7e68: ff1c6a1a04dc82f8 <<< work = &priv->mcast_task.work crash> list -hO ipoib_dev_priv.multicast_list ff1c6a1a04dc8000 (empty) crash> ipoib_dev_priv.mcast_task.work.func,mcast_mutex.owner.counter ff1c6a1a04dc8000 mcast_task.work.func = 0xffffffffc0944910 <ipoib_mcast_join_task>, mcast_mutex.owner.counter = 0xff1c69998efec000 crash> b 8 PID: 8 TASK: ff1c69998efec000 CPU: 33 COMMAND: "kworker/u72:0" -- #3 [ff646f1980153d50] wait_for_completion+0x96 at ffffffff9c7d7646 #4 [ff646f1980153d90] ipoib_mcast_remove_list+0x56 at ffffffffc0944dc6 [ib_ipoib] #5 [ff646f1980153de8] ipoib_mcast_dev_flush+0x1a7 at ffffffffc09455a7 [ib_ipoib] #6 [ff646f1980153e58] __ipoib_ib_dev_flush+0x1a4 at ffffffffc09431a4 [ib_ipoib] #7 [ff ---truncated---

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: Fix deadlock in ieee80211_sta_ps_deliver_wakeup() The ieee80211_sta_ps_deliver_wakeup() function takes sta->ps_lock to synchronizes with ieee80211_tx_h_unicast_ps_buf() which is called from softirq context. However using only spin_lock() to get sta->ps_lock in ieee80211_sta_ps_deliver_wakeup() does not prevent softirq to execute on this same CPU, to run ieee80211_tx_h_unicast_ps_buf() and try to take this same lock ending in deadlock. Below is an example of rcu stall that arises in such situation. rcu: INFO: rcu_sched self-detected stall on CPU rcu: 2-....: (42413413 ticks this GP) idle=b154/1/0x4000000000000000 softirq=1763/1765 fqs=21206996 rcu: (t=42586894 jiffies g=2057 q=362405 ncpus=4) CPU: 2 PID: 719 Comm: wpa_supplicant Tainted: G W 6.4.0-02158-g1b062f552873 #742 Hardware name: RPT (r1) (DT) pstate: 00000005 (nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : queued_spin_lock_slowpath+0x58/0x2d0 lr : invoke_tx_handlers_early+0x5b4/0x5c0 sp : ffff00001ef64660 x29: ffff00001ef64660 x28: ffff000009bc1070 x27: ffff000009bc0ad8 x26: ffff000009bc0900 x25: ffff00001ef647a8 x24: 0000000000000000 x23: ffff000009bc0900 x22: ffff000009bc0900 x21: ffff00000ac0e000 x20: ffff00000a279e00 x19: ffff00001ef646e8 x18: 0000000000000000 x17: ffff800016468000 x16: ffff00001ef608c0 x15: 0010533c93f64f80 x14: 0010395c9faa3946 x13: 0000000000000000 x12: 00000000fa83b2da x11: 000000012edeceea x10: ffff0000010fbe00 x9 : 0000000000895440 x8 : 000000000010533c x7 : ffff00000ad8b740 x6 : ffff00000c350880 x5 : 0000000000000007 x4 : 0000000000000001 x3 : 0000000000000000 x2 : 0000000000000000 x1 : 0000000000000001 x0 : ffff00000ac0e0e8 Call trace: queued_spin_lock_slowpath+0x58/0x2d0 ieee80211_tx+0x80/0x12c ieee80211_tx_pending+0x110/0x278 tasklet_action_common.constprop.0+0x10c/0x144 tasklet_action+0x20/0x28 _stext+0x11c/0x284 ____do_softirq+0xc/0x14 call_on_irq_stack+0x24/0x34 do_softirq_own_stack+0x18/0x20 do_softirq+0x74/0x7c __local_bh_enable_ip+0xa0/0xa4 _ieee80211_wake_txqs+0x3b0/0x4b8 __ieee80211_wake_queue+0x12c/0x168 ieee80211_add_pending_skbs+0xec/0x138 ieee80211_sta_ps_deliver_wakeup+0x2a4/0x480 ieee80211_mps_sta_status_update.part.0+0xd8/0x11c ieee80211_mps_sta_status_update+0x18/0x24 sta_apply_parameters+0x3bc/0x4c0 ieee80211_change_station+0x1b8/0x2dc nl80211_set_station+0x444/0x49c genl_family_rcv_msg_doit.isra.0+0xa4/0xfc genl_rcv_msg+0x1b0/0x244 netlink_rcv_skb+0x38/0x10c genl_rcv+0x34/0x48 netlink_unicast+0x254/0x2bc netlink_sendmsg+0x190/0x3b4 ____sys_sendmsg+0x1e8/0x218 ___sys_sendmsg+0x68/0x8c __sys_sendmsg+0x44/0x84 __arm64_sys_sendmsg+0x20/0x28 do_el0_svc+0x6c/0xe8 el0_svc+0x14/0x48 el0t_64_sync_handler+0xb0/0xb4 el0t_64_sync+0x14c/0x150 Using spin_lock_bh()/spin_unlock_bh() instead prevents softirq to raise on the same CPU that is holding the lock.

In the Linux kernel, the following vulnerability has been resolved: io_uring/rsrc: don't lock while !TASK_RUNNING There is a report of io_rsrc_ref_quiesce() locking a mutex while not TASK_RUNNING, which is due to forgetting restoring the state back after io_run_task_work_sig() and attempts to break out of the waiting loop. do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffff815d2494>] prepare_to_wait+0xa4/0x380 kernel/sched/wait.c:237 WARNING: CPU: 2 PID: 397056 at kernel/sched/core.c:10099 __might_sleep+0x114/0x160 kernel/sched/core.c:10099 RIP: 0010:__might_sleep+0x114/0x160 kernel/sched/core.c:10099 Call Trace: <TASK> __mutex_lock_common kernel/locking/mutex.c:585 [inline] __mutex_lock+0xb4/0x940 kernel/locking/mutex.c:752 io_rsrc_ref_quiesce+0x590/0x940 io_uring/rsrc.c:253 io_sqe_buffers_unregister+0xa2/0x340 io_uring/rsrc.c:799 __io_uring_register io_uring/register.c:424 [inline] __do_sys_io_uring_register+0x5b9/0x2400 io_uring/register.c:613 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xd8/0x270 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x6f/0x77

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: Add missing lock in cfg80211_check_and_end_cac() Callers of wdev_chandef() must hold the wiphy mutex. But the worker cfg80211_propagate_cac_done_wk() never takes the lock. Which triggers the warning below with the mesh_peer_connected_dfs test from hostapd and not (yet) released mac80211 code changes: WARNING: CPU: 0 PID: 495 at net/wireless/chan.c:1552 wdev_chandef+0x60/0x165 Modules linked in: CPU: 0 UID: 0 PID: 495 Comm: kworker/u4:2 Not tainted 6.14.0-rc5-wt-g03960e6f9d47 #33 13c287eeabfe1efea01c0bcc863723ab082e17cf Workqueue: cfg80211 cfg80211_propagate_cac_done_wk Stack: 00000000 00000001 ffffff00 6093267c 00000000 6002ec30 6d577c50 60037608 00000000 67e8d108 6063717b 00000000 Call Trace: [<6002ec30>] ? _printk+0x0/0x98 [<6003c2b3>] show_stack+0x10e/0x11a [<6002ec30>] ? _printk+0x0/0x98 [<60037608>] dump_stack_lvl+0x71/0xb8 [<6063717b>] ? wdev_chandef+0x60/0x165 [<6003766d>] dump_stack+0x1e/0x20 [<6005d1b7>] __warn+0x101/0x20f [<6005d3a8>] warn_slowpath_fmt+0xe3/0x15d [<600b0c5c>] ? mark_lock.part.0+0x0/0x4ec [<60751191>] ? __this_cpu_preempt_check+0x0/0x16 [<600b11a2>] ? mark_held_locks+0x5a/0x6e [<6005d2c5>] ? warn_slowpath_fmt+0x0/0x15d [<60052e53>] ? unblock_signals+0x3a/0xe7 [<60052f2d>] ? um_set_signals+0x2d/0x43 [<60751191>] ? __this_cpu_preempt_check+0x0/0x16 [<607508b2>] ? lock_is_held_type+0x207/0x21f [<6063717b>] wdev_chandef+0x60/0x165 [<605f89b4>] regulatory_propagate_dfs_state+0x247/0x43f [<60052f00>] ? um_set_signals+0x0/0x43 [<605e6bfd>] cfg80211_propagate_cac_done_wk+0x3a/0x4a [<6007e460>] process_scheduled_works+0x3bc/0x60e [<6007d0ec>] ? move_linked_works+0x4d/0x81 [<6007d120>] ? assign_work+0x0/0xaa [<6007f81f>] worker_thread+0x220/0x2dc [<600786ef>] ? set_pf_worker+0x0/0x57 [<60087c96>] ? to_kthread+0x0/0x43 [<6008ab3c>] kthread+0x2d3/0x2e2 [<6007f5ff>] ? worker_thread+0x0/0x2dc [<6006c05b>] ? calculate_sigpending+0x0/0x56 [<6003b37d>] new_thread_handler+0x4a/0x64 irq event stamp: 614611 hardirqs last enabled at (614621): [<00000000600bc96b>] __up_console_sem+0x82/0xaf hardirqs last disabled at (614630): [<00000000600bc92c>] __up_console_sem+0x43/0xaf softirqs last enabled at (614268): [<00000000606c55c6>] __ieee80211_wake_queue+0x933/0x985 softirqs last disabled at (614266): [<00000000606c52d6>] __ieee80211_wake_queue+0x643/0x985

In the Linux kernel, the following vulnerability has been resolved: serial: max3100: Lock port->lock when calling uart_handle_cts_change() uart_handle_cts_change() has to be called with port lock taken, Since we run it in a separate work, the lock may not be taken at the time of running. Make sure that it's taken by explicitly doing that. Without it we got a splat: WARNING: CPU: 0 PID: 10 at drivers/tty/serial/serial_core.c:3491 uart_handle_cts_change+0xa6/0xb0 ... Workqueue: max3100-0 max3100_work [max3100] RIP: 0010:uart_handle_cts_change+0xa6/0xb0 ... max3100_handlerx+0xc5/0x110 [max3100] max3100_work+0x12a/0x340 [max3100]

In the Linux kernel, the following vulnerability has been resolved: ALSA: Fix deadlocks with kctl removals at disconnection In snd_card_disconnect(), we set card->shutdown flag at the beginning, call callbacks and do sync for card->power_ref_sleep waiters at the end. The callback may delete a kctl element, and this can lead to a deadlock when the device was in the suspended state. Namely: * A process waits for the power up at snd_power_ref_and_wait() in snd_ctl_info() or read/write() inside card->controls_rwsem. * The system gets disconnected meanwhile, and the driver tries to delete a kctl via snd_ctl_remove*(); it tries to take card->controls_rwsem again, but this is already locked by the above. Since the sleeper isn't woken up, this deadlocks. An easy fix is to wake up sleepers before processing the driver disconnect callbacks but right after setting the card->shutdown flag. Then all sleepers will abort immediately, and the code flows again. So, basically this patch moves the wait_event() call at the right timing. While we're at it, just to be sure, call wait_event_all() instead of wait_event(), although we don't use exclusive events on this queue for now.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix deadlock on SRQ async events. xa_lock for SRQ table may be required in AEQ. Use xa_store_irq()/ xa_erase_irq() to avoid deadlock.

In the Linux kernel, the following vulnerability has been resolved: eth: sungem: remove .ndo_poll_controller to avoid deadlocks Erhard reports netpoll warnings from sungem: netpoll_send_skb_on_dev(): eth0 enabled interrupts in poll (gem_start_xmit+0x0/0x398) WARNING: CPU: 1 PID: 1 at net/core/netpoll.c:370 netpoll_send_skb+0x1fc/0x20c gem_poll_controller() disables interrupts, which may sleep. We can't sleep in netpoll, it has interrupts disabled completely. Strangely, gem_poll_controller() doesn't even poll the completions, and instead acts as if an interrupt has fired so it just schedules NAPI and exits. None of this has been necessary for years, since netpoll invokes NAPI directly.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix deadlock in smb2_find_smb_tcon() Unlock cifs_tcp_ses_lock before calling cifs_put_smb_ses() to avoid such deadlock.

In the Linux kernel, the following vulnerability has been resolved: netrom: fix possible dead-lock in nr_rt_ioctl() syzbot loves netrom, and found a possible deadlock in nr_rt_ioctl [1] Make sure we always acquire nr_node_list_lock before nr_node_lock(nr_node) [1] WARNING: possible circular locking dependency detected 6.9.0-rc7-syzkaller-02147-g654de42f3fc6 #0 Not tainted ------------------------------------------------------ syz-executor350/5129 is trying to acquire lock: ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline] ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: nr_node_lock include/net/netrom.h:152 [inline] ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: nr_dec_obs net/netrom/nr_route.c:464 [inline] ffff8880186e2070 (&nr_node->node_lock){+...}-{2:2}, at: nr_rt_ioctl+0x1bb/0x1090 net/netrom/nr_route.c:697 but task is already holding lock: ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline] ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: nr_dec_obs net/netrom/nr_route.c:462 [inline] ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: nr_rt_ioctl+0x10a/0x1090 net/netrom/nr_route.c:697 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (nr_node_list_lock){+...}-{2:2}: lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754 __raw_spin_lock_bh include/linux/spinlock_api_smp.h:126 [inline] _raw_spin_lock_bh+0x35/0x50 kernel/locking/spinlock.c:178 spin_lock_bh include/linux/spinlock.h:356 [inline] nr_remove_node net/netrom/nr_route.c:299 [inline] nr_del_node+0x4b4/0x820 net/netrom/nr_route.c:355 nr_rt_ioctl+0xa95/0x1090 net/netrom/nr_route.c:683 sock_do_ioctl+0x158/0x460 net/socket.c:1222 sock_ioctl+0x629/0x8e0 net/socket.c:1341 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:904 [inline] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:890 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f -> #0 (&nr_node->node_lock){+...}-{2:2}: check_prev_add kernel/locking/lockdep.c:3134 [inline] check_prevs_add kernel/locking/lockdep.c:3253 [inline] validate_chain+0x18cb/0x58e0 kernel/locking/lockdep.c:3869 __lock_acquire+0x1346/0x1fd0 kernel/locking/lockdep.c:5137 lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754 __raw_spin_lock_bh include/linux/spinlock_api_smp.h:126 [inline] _raw_spin_lock_bh+0x35/0x50 kernel/locking/spinlock.c:178 spin_lock_bh include/linux/spinlock.h:356 [inline] nr_node_lock include/net/netrom.h:152 [inline] nr_dec_obs net/netrom/nr_route.c:464 [inline] nr_rt_ioctl+0x1bb/0x1090 net/netrom/nr_route.c:697 sock_do_ioctl+0x158/0x460 net/socket.c:1222 sock_ioctl+0x629/0x8e0 net/socket.c:1341 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:904 [inline] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:890 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(nr_node_list_lock); lock(&nr_node->node_lock); lock(nr_node_list_lock); lock(&nr_node->node_lock); *** DEADLOCK *** 1 lock held by syz-executor350/5129: #0: ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline] #0: ffffffff8f7053b8 (nr_node_list_lock){+...}-{2:2}, at: nr_dec_obs net/netrom/nr_route.c:462 [inline] #0: ffffffff8f70 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: dma-buf/sw-sync: don't enable IRQ from sync_print_obj() Since commit a6aa8fca4d79 ("dma-buf/sw-sync: Reduce irqsave/irqrestore from known context") by error replaced spin_unlock_irqrestore() with spin_unlock_irq() for both sync_debugfs_show() and sync_print_obj() despite sync_print_obj() is called from sync_debugfs_show(), lockdep complains inconsistent lock state warning. Use plain spin_{lock,unlock}() for sync_print_obj(), for sync_debugfs_show() is already using spin_{lock,unlock}_irq().

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Reload only IB representors upon lag disable/enable On lag disable, the bond IB device along with all of its representors are destroyed, and then the slaves' representors get reloaded. In case the slave IB representor load fails, the eswitch error flow unloads all representors, including ethernet representors, where the netdevs get detached and removed from lag bond. Such flow is inaccurate as the lag driver is not responsible for loading/unloading ethernet representors. Furthermore, the flow described above begins by holding lag lock to prevent bond changes during disable flow. However, when reaching the ethernet representors detachment from lag, the lag lock is required again, triggering the following deadlock: Call trace: __switch_to+0xf4/0x148 __schedule+0x2c8/0x7d0 schedule+0x50/0xe0 schedule_preempt_disabled+0x18/0x28 __mutex_lock.isra.13+0x2b8/0x570 __mutex_lock_slowpath+0x1c/0x28 mutex_lock+0x4c/0x68 mlx5_lag_remove_netdev+0x3c/0x1a0 [mlx5_core] mlx5e_uplink_rep_disable+0x70/0xa0 [mlx5_core] mlx5e_detach_netdev+0x6c/0xb0 [mlx5_core] mlx5e_netdev_change_profile+0x44/0x138 [mlx5_core] mlx5e_netdev_attach_nic_profile+0x28/0x38 [mlx5_core] mlx5e_vport_rep_unload+0x184/0x1b8 [mlx5_core] mlx5_esw_offloads_rep_load+0xd8/0xe0 [mlx5_core] mlx5_eswitch_reload_reps+0x74/0xd0 [mlx5_core] mlx5_disable_lag+0x130/0x138 [mlx5_core] mlx5_lag_disable_change+0x6c/0x70 [mlx5_core] // hold ldev->lock mlx5_devlink_eswitch_mode_set+0xc0/0x410 [mlx5_core] devlink_nl_cmd_eswitch_set_doit+0xdc/0x180 genl_family_rcv_msg_doit.isra.17+0xe8/0x138 genl_rcv_msg+0xe4/0x220 netlink_rcv_skb+0x44/0x108 genl_rcv+0x40/0x58 netlink_unicast+0x198/0x268 netlink_sendmsg+0x1d4/0x418 sock_sendmsg+0x54/0x60 __sys_sendto+0xf4/0x120 __arm64_sys_sendto+0x30/0x40 el0_svc_common+0x8c/0x120 do_el0_svc+0x30/0xa0 el0_svc+0x20/0x30 el0_sync_handler+0x90/0xb8 el0_sync+0x160/0x180 Thus, upon lag enable/disable, load and unload only the IB representors of the slaves preventing the deadlock mentioned above. While at it, refactor the mlx5_esw_offloads_rep_load() function to have a static helper method for its internal logic, in symmetry with the representor unload design.

In the Linux kernel, the following vulnerability has been resolved: md/raid5: fix deadlock that raid5d() wait for itself to clear MD_SB_CHANGE_PENDING Xiao reported that lvm2 test lvconvert-raid-takeover.sh can hang with small possibility, the root cause is exactly the same as commit bed9e27baf52 ("Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d"") However, Dan reported another hang after that, and junxiao investigated the problem and found out that this is caused by plugged bio can't issue from raid5d(). Current implementation in raid5d() has a weird dependence: 1) md_check_recovery() from raid5d() must hold 'reconfig_mutex' to clear MD_SB_CHANGE_PENDING; 2) raid5d() handles IO in a deadloop, until all IO are issued; 3) IO from raid5d() must wait for MD_SB_CHANGE_PENDING to be cleared; This behaviour is introduce before v2.6, and for consequence, if other context hold 'reconfig_mutex', and md_check_recovery() can't update super_block, then raid5d() will waste one cpu 100% by the deadloop, until 'reconfig_mutex' is released. Refer to the implementation from raid1 and raid10, fix this problem by skipping issue IO if MD_SB_CHANGE_PENDING is still set after md_check_recovery(), daemon thread will be woken up when 'reconfig_mutex' is released. Meanwhile, the hang problem will be fixed as well.

The ptrace_start function in kernel/ptrace.c in the Linux kernel 2.6.18 does not properly handle simultaneous execution of the do_coredump function, which allows local users to cause a denial of service (deadlock) via vectors involving the ptrace system call and a coredumping thread.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: handle the case of pci_channel_io_frozen only in amdgpu_pci_resume In current code, when a PCI error state pci_channel_io_normal is detectd, it will report PCI_ERS_RESULT_CAN_RECOVER status to PCI driver, and PCI driver will continue the execution of PCI resume callback report_resume by pci_walk_bridge, and the callback will go into amdgpu_pci_resume finally, where write lock is releasd unconditionally without acquiring such lock first. In this case, a deadlock will happen when other threads start to acquire the read lock. To fix this, add a member in amdgpu_device strucutre to cache pci_channel_state, and only continue the execution in amdgpu_pci_resume when it's pci_channel_io_frozen.

In the Linux kernel, the following vulnerability has been resolved: Revert "media: v4l2-ctrls: show all owned controls in log_status" This reverts commit 9801b5b28c6929139d6fceeee8d739cc67bb2739. This patch introduced a potential deadlock scenario: [Wed May 8 10:02:06 2024] Possible unsafe locking scenario: [Wed May 8 10:02:06 2024] CPU0 CPU1 [Wed May 8 10:02:06 2024] ---- ---- [Wed May 8 10:02:06 2024] lock(vivid_ctrls:1620:(hdl_vid_cap)->_lock); [Wed May 8 10:02:06 2024] lock(vivid_ctrls:1608:(hdl_user_vid)->_lock); [Wed May 8 10:02:06 2024] lock(vivid_ctrls:1620:(hdl_vid_cap)->_lock); [Wed May 8 10:02:06 2024] lock(vivid_ctrls:1608:(hdl_user_vid)->_lock); For now just revert.

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: Use request_module_nowait This appears to work around a deadlock regression that came in with the LED merge in 6.9. The deadlock happens on my system with 24 iwlwifi radios, so maybe it something like all worker threads are busy and some work that needs to complete cannot complete. [also remove unnecessary "load_module" var and now-wrong comment]

In the Linux kernel, the following vulnerability has been resolved: net: ks8851: Handle softirqs at the end of IRQ thread to fix hang The ks8851_irq() thread may call ks8851_rx_pkts() in case there are any packets in the MAC FIFO, which calls netif_rx(). This netif_rx() implementation is guarded by local_bh_disable() and local_bh_enable(). The local_bh_enable() may call do_softirq() to run softirqs in case any are pending. One of the softirqs is net_rx_action, which ultimately reaches the driver .start_xmit callback. If that happens, the system hangs. The entire call chain is below: ks8851_start_xmit_par from netdev_start_xmit netdev_start_xmit from dev_hard_start_xmit dev_hard_start_xmit from sch_direct_xmit sch_direct_xmit from __dev_queue_xmit __dev_queue_xmit from __neigh_update __neigh_update from neigh_update neigh_update from arp_process.constprop.0 arp_process.constprop.0 from __netif_receive_skb_one_core __netif_receive_skb_one_core from process_backlog process_backlog from __napi_poll.constprop.0 __napi_poll.constprop.0 from net_rx_action net_rx_action from __do_softirq __do_softirq from call_with_stack call_with_stack from do_softirq do_softirq from __local_bh_enable_ip __local_bh_enable_ip from netif_rx netif_rx from ks8851_irq ks8851_irq from irq_thread_fn irq_thread_fn from irq_thread irq_thread from kthread kthread from ret_from_fork The hang happens because ks8851_irq() first locks a spinlock in ks8851_par.c ks8851_lock_par() spin_lock_irqsave(&ksp->lock, ...) and with that spinlock locked, calls netif_rx(). Once the execution reaches ks8851_start_xmit_par(), it calls ks8851_lock_par() again which attempts to claim the already locked spinlock again, and the hang happens. Move the do_softirq() call outside of the spinlock protected section of ks8851_irq() by disabling BHs around the entire spinlock protected section of ks8851_irq() handler. Place local_bh_enable() outside of the spinlock protected section, so that it can trigger do_softirq() without the ks8851_par.c ks8851_lock_par() spinlock being held, and safely call ks8851_start_xmit_par() without attempting to lock the already locked spinlock. Since ks8851_irq() is protected by local_bh_disable()/local_bh_enable() now, replace netif_rx() with __netif_rx() which is not duplicating the local_bh_disable()/local_bh_enable() calls.

In the Linux kernel, the following vulnerability has been resolved: nvmet-tcp: fix incorrect locking in state_change sk callback We are not changing anything in the TCP connection state so we should not take a write_lock but rather a read lock. This caused a deadlock when running nvmet-tcp and nvme-tcp on the same system, where state_change callbacks on the host and on the controller side have causal relationship and made lockdep report on this with blktests: ================================ WARNING: inconsistent lock state 5.12.0-rc3 #1 Tainted: G I -------------------------------- inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-R} usage. nvme/1324 [HC0[0]:SC0[0]:HE1:SE1] takes: ffff888363151000 (clock-AF_INET){++-?}-{2:2}, at: nvme_tcp_state_change+0x21/0x150 [nvme_tcp] {IN-SOFTIRQ-W} state was registered at: __lock_acquire+0x79b/0x18d0 lock_acquire+0x1ca/0x480 _raw_write_lock_bh+0x39/0x80 nvmet_tcp_state_change+0x21/0x170 [nvmet_tcp] tcp_fin+0x2a8/0x780 tcp_data_queue+0xf94/0x1f20 tcp_rcv_established+0x6ba/0x1f00 tcp_v4_do_rcv+0x502/0x760 tcp_v4_rcv+0x257e/0x3430 ip_protocol_deliver_rcu+0x69/0x6a0 ip_local_deliver_finish+0x1e2/0x2f0 ip_local_deliver+0x1a2/0x420 ip_rcv+0x4fb/0x6b0 __netif_receive_skb_one_core+0x162/0x1b0 process_backlog+0x1ff/0x770 __napi_poll.constprop.0+0xa9/0x5c0 net_rx_action+0x7b3/0xb30 __do_softirq+0x1f0/0x940 do_softirq+0xa1/0xd0 __local_bh_enable_ip+0xd8/0x100 ip_finish_output2+0x6b7/0x18a0 __ip_queue_xmit+0x706/0x1aa0 __tcp_transmit_skb+0x2068/0x2e20 tcp_write_xmit+0xc9e/0x2bb0 __tcp_push_pending_frames+0x92/0x310 inet_shutdown+0x158/0x300 __nvme_tcp_stop_queue+0x36/0x270 [nvme_tcp] nvme_tcp_stop_queue+0x87/0xb0 [nvme_tcp] nvme_tcp_teardown_admin_queue+0x69/0xe0 [nvme_tcp] nvme_do_delete_ctrl+0x100/0x10c [nvme_core] nvme_sysfs_delete.cold+0x8/0xd [nvme_core] kernfs_fop_write_iter+0x2c7/0x460 new_sync_write+0x36c/0x610 vfs_write+0x5c0/0x870 ksys_write+0xf9/0x1d0 do_syscall_64+0x33/0x40 entry_SYSCALL_64_after_hwframe+0x44/0xae irq event stamp: 10687 hardirqs last enabled at (10687): [<ffffffff9ec376bd>] _raw_spin_unlock_irqrestore+0x2d/0x40 hardirqs last disabled at (10686): [<ffffffff9ec374d8>] _raw_spin_lock_irqsave+0x68/0x90 softirqs last enabled at (10684): [<ffffffff9f000608>] __do_softirq+0x608/0x940 softirqs last disabled at (10649): [<ffffffff9cdedd31>] do_softirq+0xa1/0xd0 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(clock-AF_INET); <Interrupt> lock(clock-AF_INET); *** DEADLOCK *** 5 locks held by nvme/1324: #0: ffff8884a01fe470 (sb_writers#4){.+.+}-{0:0}, at: ksys_write+0xf9/0x1d0 #1: ffff8886e435c090 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0x216/0x460 #2: ffff888104d90c38 (kn->active#255){++++}-{0:0}, at: kernfs_remove_self+0x22d/0x330 #3: ffff8884634538d0 (&queue->queue_lock){+.+.}-{3:3}, at: nvme_tcp_stop_queue+0x52/0xb0 [nvme_tcp] #4: ffff888363150d30 (sk_lock-AF_INET){+.+.}-{0:0}, at: inet_shutdown+0x59/0x300 stack backtrace: CPU: 26 PID: 1324 Comm: nvme Tainted: G I 5.12.0-rc3 #1 Hardware name: Dell Inc. PowerEdge R640/06NR82, BIOS 2.10.0 11/12/2020 Call Trace: dump_stack+0x93/0xc2 mark_lock_irq.cold+0x2c/0xb3 ? verify_lock_unused+0x390/0x390 ? stack_trace_consume_entry+0x160/0x160 ? lock_downgrade+0x100/0x100 ? save_trace+0x88/0x5e0 ? _raw_spin_unlock_irqrestore+0x2d/0x40 mark_lock+0x530/0x1470 ? mark_lock_irq+0x1d10/0x1d10 ? enqueue_timer+0x660/0x660 mark_usage+0x215/0x2a0 __lock_acquire+0x79b/0x18d0 ? tcp_schedule_loss_probe.part.0+0x38c/0x520 lock_acquire+0x1ca/0x480 ? nvme_tcp_state_change+0x21/0x150 [nvme_tcp] ? rcu_read_unlock+0x40/0x40 ? tcp_mtu_probe+0x1ae0/0x1ae0 ? kmalloc_reserve+0xa0/0xa0 ? sysfs_file_ops+0x170/0x170 _raw_read_lock+0x3d/0xa0 ? nvme_tcp_state_change+0x21/0x150 [nvme_tcp] nvme_tcp_state_change+0x21/0x150 [nvme_tcp] ? sysfs_file_ops ---truncated---

In the Linux kernel, the following vulnerability has been resolved: pds_core: Fix pdsc_check_pci_health function to use work thread When the driver notices fw_status == 0xff it tries to perform a PCI reset on itself via pci_reset_function() in the context of the driver's health thread. However, pdsc_reset_prepare calls pdsc_stop_health_thread(), which attempts to stop/flush the health thread. This results in a deadlock because the stop/flush will never complete since the driver called pci_reset_function() from the health thread context. Fix by changing the pdsc_check_pci_health_function() to queue a newly introduced pdsc_pci_reset_thread() on the pdsc's work queue. Unloading the driver in the fw_down/dead state uncovered another issue, which can be seen in the following trace: WARNING: CPU: 51 PID: 6914 at kernel/workqueue.c:1450 __queue_work+0x358/0x440 [...] RIP: 0010:__queue_work+0x358/0x440 [...] Call Trace: <TASK> ? __warn+0x85/0x140 ? __queue_work+0x358/0x440 ? report_bug+0xfc/0x1e0 ? handle_bug+0x3f/0x70 ? exc_invalid_op+0x17/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? __queue_work+0x358/0x440 queue_work_on+0x28/0x30 pdsc_devcmd_locked+0x96/0xe0 [pds_core] pdsc_devcmd_reset+0x71/0xb0 [pds_core] pdsc_teardown+0x51/0xe0 [pds_core] pdsc_remove+0x106/0x200 [pds_core] pci_device_remove+0x37/0xc0 device_release_driver_internal+0xae/0x140 driver_detach+0x48/0x90 bus_remove_driver+0x6d/0xf0 pci_unregister_driver+0x2e/0xa0 pdsc_cleanup_module+0x10/0x780 [pds_core] __x64_sys_delete_module+0x142/0x2b0 ? syscall_trace_enter.isra.18+0x126/0x1a0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7fbd9d03a14b [...] Fix this by preventing the devcmd reset if the FW is not running.

In the Linux kernel, the following vulnerability has been resolved: thermal/debugfs: Fix two locking issues with thermal zone debug With the current thermal zone locking arrangement in the debugfs code, user space can open the "mitigations" file for a thermal zone before the zone's debugfs pointer is set which will result in a NULL pointer dereference in tze_seq_start(). Moreover, thermal_debug_tz_remove() is not called under the thermal zone lock, so it can run in parallel with the other functions accessing the thermal zone's struct thermal_debugfs object. Then, it may clear tz->debugfs after one of those functions has checked it and the struct thermal_debugfs object may be freed prematurely. To address the first problem, pass a pointer to the thermal zone's struct thermal_debugfs object to debugfs_create_file() in thermal_debug_tz_add() and make tze_seq_start(), tze_seq_next(), tze_seq_stop(), and tze_seq_show() retrieve it from s->private instead of a pointer to the thermal zone object. This will ensure that tz_debugfs will be valid across the "mitigations" file accesses until thermal_debugfs_remove_id() called by thermal_debug_tz_remove() removes that file. To address the second problem, use tz->lock in thermal_debug_tz_remove() around the tz->debugfs value check (in case the same thermal zone is removed at the same time in two different threads) and its reset to NULL. Cc :6.8+ <stable@vger.kernel.org> # 6.8+

In the Linux kernel, the following vulnerability has been resolved: dma: xilinx_dpdma: Fix locking There are several places where either chan->lock or chan->vchan.lock was not held. Add appropriate locking. This fixes lockdep warnings like [ 31.077578] ------------[ cut here ]------------ [ 31.077831] WARNING: CPU: 2 PID: 40 at drivers/dma/xilinx/xilinx_dpdma.c:834 xilinx_dpdma_chan_queue_transfer+0x274/0x5e0 [ 31.077953] Modules linked in: [ 31.078019] CPU: 2 PID: 40 Comm: kworker/u12:1 Not tainted 6.6.20+ #98 [ 31.078102] Hardware name: xlnx,zynqmp (DT) [ 31.078169] Workqueue: events_unbound deferred_probe_work_func [ 31.078272] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 31.078377] pc : xilinx_dpdma_chan_queue_transfer+0x274/0x5e0 [ 31.078473] lr : xilinx_dpdma_chan_queue_transfer+0x270/0x5e0 [ 31.078550] sp : ffffffc083bb2e10 [ 31.078590] x29: ffffffc083bb2e10 x28: 0000000000000000 x27: ffffff880165a168 [ 31.078754] x26: ffffff880164e920 x25: ffffff880164eab8 x24: ffffff880164d480 [ 31.078920] x23: ffffff880165a148 x22: ffffff880164e988 x21: 0000000000000000 [ 31.079132] x20: ffffffc082aa3000 x19: ffffff880164e880 x18: 0000000000000000 [ 31.079295] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 [ 31.079453] x14: 0000000000000000 x13: ffffff8802263dc0 x12: 0000000000000001 [ 31.079613] x11: 0001ffc083bb2e34 x10: 0001ff880164e98f x9 : 0001ffc082aa3def [ 31.079824] x8 : 0001ffc082aa3dec x7 : 0000000000000000 x6 : 0000000000000516 [ 31.079982] x5 : ffffffc7f8d43000 x4 : ffffff88003c9c40 x3 : ffffffffffffffff [ 31.080147] x2 : ffffffc7f8d43000 x1 : 00000000000000c0 x0 : 0000000000000000 [ 31.080307] Call trace: [ 31.080340] xilinx_dpdma_chan_queue_transfer+0x274/0x5e0 [ 31.080518] xilinx_dpdma_issue_pending+0x11c/0x120 [ 31.080595] zynqmp_disp_layer_update+0x180/0x3ac [ 31.080712] zynqmp_dpsub_plane_atomic_update+0x11c/0x21c [ 31.080825] drm_atomic_helper_commit_planes+0x20c/0x684 [ 31.080951] drm_atomic_helper_commit_tail+0x5c/0xb0 [ 31.081139] commit_tail+0x234/0x294 [ 31.081246] drm_atomic_helper_commit+0x1f8/0x210 [ 31.081363] drm_atomic_commit+0x100/0x140 [ 31.081477] drm_client_modeset_commit_atomic+0x318/0x384 [ 31.081634] drm_client_modeset_commit_locked+0x8c/0x24c [ 31.081725] drm_client_modeset_commit+0x34/0x5c [ 31.081812] __drm_fb_helper_restore_fbdev_mode_unlocked+0x104/0x168 [ 31.081899] drm_fb_helper_set_par+0x50/0x70 [ 31.081971] fbcon_init+0x538/0xc48 [ 31.082047] visual_init+0x16c/0x23c [ 31.082207] do_bind_con_driver.isra.0+0x2d0/0x634 [ 31.082320] do_take_over_console+0x24c/0x33c [ 31.082429] do_fbcon_takeover+0xbc/0x1b0 [ 31.082503] fbcon_fb_registered+0x2d0/0x34c [ 31.082663] register_framebuffer+0x27c/0x38c [ 31.082767] __drm_fb_helper_initial_config_and_unlock+0x5c0/0x91c [ 31.082939] drm_fb_helper_initial_config+0x50/0x74 [ 31.083012] drm_fbdev_dma_client_hotplug+0xb8/0x108 [ 31.083115] drm_client_register+0xa0/0xf4 [ 31.083195] drm_fbdev_dma_setup+0xb0/0x1cc [ 31.083293] zynqmp_dpsub_drm_init+0x45c/0x4e0 [ 31.083431] zynqmp_dpsub_probe+0x444/0x5e0 [ 31.083616] platform_probe+0x8c/0x13c [ 31.083713] really_probe+0x258/0x59c [ 31.083793] __driver_probe_device+0xc4/0x224 [ 31.083878] driver_probe_device+0x70/0x1c0 [ 31.083961] __device_attach_driver+0x108/0x1e0 [ 31.084052] bus_for_each_drv+0x9c/0x100 [ 31.084125] __device_attach+0x100/0x298 [ 31.084207] device_initial_probe+0x14/0x20 [ 31.084292] bus_probe_device+0xd8/0xdc [ 31.084368] deferred_probe_work_func+0x11c/0x180 [ 31.084451] process_one_work+0x3ac/0x988 [ 31.084643] worker_thread+0x398/0x694 [ 31.084752] kthread+0x1bc/0x1c0 [ 31.084848] ret_from_fork+0x10/0x20 [ 31.084932] irq event stamp: 64549 [ 31.084970] hardirqs last enabled at (64548): [<ffffffc081adf35c>] _raw_spin_unlock_irqrestore+0x80/0x90 [ 31.085157] ---truncated---

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Release hbalock before calling lpfc_worker_wake_up() lpfc_worker_wake_up() calls the lpfc_work_done() routine, which takes the hbalock. Thus, lpfc_worker_wake_up() should not be called while holding the hbalock to avoid potential deadlock.

In the Linux kernel, the following vulnerability has been resolved: bpf, sockmap: Prevent lock inversion deadlock in map delete elem syzkaller started using corpuses where a BPF tracing program deletes elements from a sockmap/sockhash map. Because BPF tracing programs can be invoked from any interrupt context, locks taken during a map_delete_elem operation must be hardirq-safe. Otherwise a deadlock due to lock inversion is possible, as reported by lockdep: CPU0 CPU1 ---- ---- lock(&htab->buckets[i].lock); local_irq_disable(); lock(&host->lock); lock(&htab->buckets[i].lock); <Interrupt> lock(&host->lock); Locks in sockmap are hardirq-unsafe by design. We expects elements to be deleted from sockmap/sockhash only in task (normal) context with interrupts enabled, or in softirq context. Detect when map_delete_elem operation is invoked from a context which is _not_ hardirq-unsafe, that is interrupts are disabled, and bail out with an error. Note that map updates are not affected by this issue. BPF verifier does not allow updating sockmap/sockhash from a BPF tracing program today.

In the Linux kernel, the following vulnerability has been resolved: drm/ast: Fix soft lockup There is a while-loop in ast_dp_set_on_off() that could lead to infinite-loop. This is because the register, VGACRI-Dx, checked in this API is a scratch register actually controlled by a MCU, named DPMCU, in BMC. These scratch registers are protected by scu-lock. If suc-lock is not off, DPMCU can not update these registers and then host will have soft lockup due to never updated status. DPMCU is used to control DP and relative registers to handshake with host's VGA driver. Even the most time-consuming task, DP's link training, is less than 100ms. 200ms should be enough.

In the Linux kernel, the following vulnerability has been resolved: md/dm-raid: don't call md_reap_sync_thread() directly Currently md_reap_sync_thread() is called from raid_message() directly without holding 'reconfig_mutex', this is definitely unsafe because md_reap_sync_thread() can change many fields that is protected by 'reconfig_mutex'. However, hold 'reconfig_mutex' here is still problematic because this will cause deadlock, for example, commit 130443d60b1b ("md: refactor idle/frozen_sync_thread() to fix deadlock"). Fix this problem by using stop_sync_thread() to unregister sync_thread, like md/raid did.

In the Linux kernel, the following vulnerability has been resolved: LoongArch: Define the __io_aw() hook as mmiowb() Commit fb24ea52f78e0d595852e ("drivers: Remove explicit invocations of mmiowb()") remove all mmiowb() in drivers, but it says: "NOTE: mmiowb() has only ever guaranteed ordering in conjunction with spin_unlock(). However, pairing each mmiowb() removal in this patch with the corresponding call to spin_unlock() is not at all trivial, so there is a small chance that this change may regress any drivers incorrectly relying on mmiowb() to order MMIO writes between CPUs using lock-free synchronisation." The mmio in radeon_ring_commit() is protected by a mutex rather than a spinlock, but in the mutex fastpath it behaves similar to spinlock. We can add mmiowb() calls in the radeon driver but the maintainer says he doesn't like such a workaround, and radeon is not the only example of mutex protected mmio. So we should extend the mmiowb tracking system from spinlock to mutex, and maybe other locking primitives. This is not easy and error prone, so we solve it in the architectural code, by simply defining the __io_aw() hook as mmiowb(). And we no longer need to override queued_spin_unlock() so use the generic definition. Without this, we get such an error when run 'glxgears' on weak ordering architectures such as LoongArch: radeon 0000:04:00.0: ring 0 stalled for more than 10324msec radeon 0000:04:00.0: ring 3 stalled for more than 10240msec radeon 0000:04:00.0: GPU lockup (current fence id 0x000000000001f412 last fence id 0x000000000001f414 on ring 3) radeon 0000:04:00.0: GPU lockup (current fence id 0x000000000000f940 last fence id 0x000000000000f941 on ring 0) radeon 0000:04:00.0: scheduling IB failed (-35). [drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35) radeon 0000:04:00.0: scheduling IB failed (-35). [drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35) radeon 0000:04:00.0: scheduling IB failed (-35). [drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35) radeon 0000:04:00.0: scheduling IB failed (-35). [drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35) radeon 0000:04:00.0: scheduling IB failed (-35). [drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35) radeon 0000:04:00.0: scheduling IB failed (-35). [drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35) radeon 0000:04:00.0: scheduling IB failed (-35). [drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)

The inotify_read function in the Linux kernel 2.6.27 to 2.6.27.13, 2.6.28 to 2.6.28.2, and 2.6.29-rc3 allows local users to cause a denial of service (OOPS) via a read with an invalid address to an inotify instance, which causes the device's event list mutex to be unlocked twice and prevents proper synchronization of a data structure for the inotify instance.

In the Linux kernel, the following vulnerability has been resolved: NFS: Fix nfs_netfs_issue_read() xarray locking for writeback interrupt The loop inside nfs_netfs_issue_read() currently does not disable interrupts while iterating through pages in the xarray to submit for NFS read. This is not safe though since after taking xa_lock, another page in the mapping could be processed for writeback inside an interrupt, and deadlock can occur. The fix is simple and clean if we use xa_for_each_range(), which handles the iteration with RCU while reducing code complexity. The problem is easily reproduced with the following test: mount -o vers=3,fsc 127.0.0.1:/export /mnt/nfs dd if=/dev/zero of=/mnt/nfs/file1.bin bs=4096 count=1 echo 3 > /proc/sys/vm/drop_caches dd if=/mnt/nfs/file1.bin of=/dev/null umount /mnt/nfs On the console with a lockdep-enabled kernel a message similar to the following will be seen: ================================ WARNING: inconsistent lock state 6.7.0-lockdbg+ #10 Not tainted -------------------------------- inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage. test5/1708 [HC0[0]:SC0[0]:HE1:SE1] takes: ffff888127baa598 (&xa->xa_lock#4){+.?.}-{3:3}, at: nfs_netfs_issue_read+0x1b2/0x4b0 [nfs] {IN-SOFTIRQ-W} state was registered at: lock_acquire+0x144/0x380 _raw_spin_lock_irqsave+0x4e/0xa0 __folio_end_writeback+0x17e/0x5c0 folio_end_writeback+0x93/0x1b0 iomap_finish_ioend+0xeb/0x6a0 blk_update_request+0x204/0x7f0 blk_mq_end_request+0x30/0x1c0 blk_complete_reqs+0x7e/0xa0 __do_softirq+0x113/0x544 __irq_exit_rcu+0xfe/0x120 irq_exit_rcu+0xe/0x20 sysvec_call_function_single+0x6f/0x90 asm_sysvec_call_function_single+0x1a/0x20 pv_native_safe_halt+0xf/0x20 default_idle+0x9/0x20 default_idle_call+0x67/0xa0 do_idle+0x2b5/0x300 cpu_startup_entry+0x34/0x40 start_secondary+0x19d/0x1c0 secondary_startup_64_no_verify+0x18f/0x19b irq event stamp: 176891 hardirqs last enabled at (176891): [<ffffffffa67a0be4>] _raw_spin_unlock_irqrestore+0x44/0x60 hardirqs last disabled at (176890): [<ffffffffa67a0899>] _raw_spin_lock_irqsave+0x79/0xa0 softirqs last enabled at (176646): [<ffffffffa515d91e>] __irq_exit_rcu+0xfe/0x120 softirqs last disabled at (176633): [<ffffffffa515d91e>] __irq_exit_rcu+0xfe/0x120 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&xa->xa_lock#4); <Interrupt> lock(&xa->xa_lock#4); *** DEADLOCK *** 2 locks held by test5/1708: #0: ffff888127baa498 (&sb->s_type->i_mutex_key#22){++++}-{4:4}, at: nfs_start_io_read+0x28/0x90 [nfs] #1: ffff888127baa650 (mapping.invalidate_lock#3){.+.+}-{4:4}, at: page_cache_ra_unbounded+0xa4/0x280 stack backtrace: CPU: 6 PID: 1708 Comm: test5 Kdump: loaded Not tainted 6.7.0-lockdbg+ Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-1.fc39 04/01/2014 Call Trace: dump_stack_lvl+0x5b/0x90 mark_lock+0xb3f/0xd20 __lock_acquire+0x77b/0x3360 _raw_spin_lock+0x34/0x80 nfs_netfs_issue_read+0x1b2/0x4b0 [nfs] netfs_begin_read+0x77f/0x980 [netfs] nfs_netfs_readahead+0x45/0x60 [nfs] nfs_readahead+0x323/0x5a0 [nfs] read_pages+0xf3/0x5c0 page_cache_ra_unbounded+0x1c8/0x280 filemap_get_pages+0x38c/0xae0 filemap_read+0x206/0x5e0 nfs_file_read+0xb7/0x140 [nfs] vfs_read+0x2a9/0x460 ksys_read+0xb7/0x140

In the Linux kernel, the following vulnerability has been resolved: net: implement lockless setsockopt(SO_PEEK_OFF) syzbot reported a lockdep violation [1] involving af_unix support of SO_PEEK_OFF. Since SO_PEEK_OFF is inherently not thread safe (it uses a per-socket sk_peek_off field), there is really no point to enforce a pointless thread safety in the kernel. After this patch : - setsockopt(SO_PEEK_OFF) no longer acquires the socket lock. - skb_consume_udp() no longer has to acquire the socket lock. - af_unix no longer needs a special version of sk_set_peek_off(), because it does not lock u->iolock anymore. As a followup, we could replace prot->set_peek_off to be a boolean and avoid an indirect call, since we always use sk_set_peek_off(). [1] WARNING: possible circular locking dependency detected 6.8.0-rc4-syzkaller-00267-g0f1dd5e91e2b #0 Not tainted syz-executor.2/30025 is trying to acquire lock: ffff8880765e7d80 (&u->iolock){+.+.}-{3:3}, at: unix_set_peek_off+0x26/0xa0 net/unix/af_unix.c:789 but task is already holding lock: ffff8880765e7930 (sk_lock-AF_UNIX){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1691 [inline] ffff8880765e7930 (sk_lock-AF_UNIX){+.+.}-{0:0}, at: sockopt_lock_sock net/core/sock.c:1060 [inline] ffff8880765e7930 (sk_lock-AF_UNIX){+.+.}-{0:0}, at: sk_setsockopt+0xe52/0x3360 net/core/sock.c:1193 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (sk_lock-AF_UNIX){+.+.}-{0:0}: lock_acquire+0x1e3/0x530 kernel/locking/lockdep.c:5754 lock_sock_nested+0x48/0x100 net/core/sock.c:3524 lock_sock include/net/sock.h:1691 [inline] __unix_dgram_recvmsg+0x1275/0x12c0 net/unix/af_unix.c:2415 sock_recvmsg_nosec+0x18e/0x1d0 net/socket.c:1046 ____sys_recvmsg+0x3c0/0x470 net/socket.c:2801 ___sys_recvmsg net/socket.c:2845 [inline] do_recvmmsg+0x474/0xae0 net/socket.c:2939 __sys_recvmmsg net/socket.c:3018 [inline] __do_sys_recvmmsg net/socket.c:3041 [inline] __se_sys_recvmmsg net/socket.c:3034 [inline] __x64_sys_recvmmsg+0x199/0x250 net/socket.c:3034 do_syscall_64+0xf9/0x240 entry_SYSCALL_64_after_hwframe+0x6f/0x77 -> #0 (&u->iolock){+.+.}-{3:3}: check_prev_add kernel/locking/lockdep.c:3134 [inline] check_prevs_add kernel/locking/lockdep.c:3253 [inline] validate_chain+0x18ca/0x58e0 kernel/locking/lockdep.c:3869 __lock_acquire+0x1345/0x1fd0 kernel/locking/lockdep.c:5137 lock_acquire+0x1e3/0x530 kernel/locking/lockdep.c:5754 __mutex_lock_common kernel/locking/mutex.c:608 [inline] __mutex_lock+0x136/0xd70 kernel/locking/mutex.c:752 unix_set_peek_off+0x26/0xa0 net/unix/af_unix.c:789 sk_setsockopt+0x207e/0x3360 do_sock_setsockopt+0x2fb/0x720 net/socket.c:2307 __sys_setsockopt+0x1ad/0x250 net/socket.c:2334 __do_sys_setsockopt net/socket.c:2343 [inline] __se_sys_setsockopt net/socket.c:2340 [inline] __x64_sys_setsockopt+0xb5/0xd0 net/socket.c:2340 do_syscall_64+0xf9/0x240 entry_SYSCALL_64_after_hwframe+0x6f/0x77 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(sk_lock-AF_UNIX); lock(&u->iolock); lock(sk_lock-AF_UNIX); lock(&u->iolock); *** DEADLOCK *** 1 lock held by syz-executor.2/30025: #0: ffff8880765e7930 (sk_lock-AF_UNIX){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1691 [inline] #0: ffff8880765e7930 (sk_lock-AF_UNIX){+.+.}-{0:0}, at: sockopt_lock_sock net/core/sock.c:1060 [inline] #0: ffff8880765e7930 (sk_lock-AF_UNIX){+.+.}-{0:0}, at: sk_setsockopt+0xe52/0x3360 net/core/sock.c:1193 stack backtrace: CPU: 0 PID: 30025 Comm: syz-executor.2 Not tainted 6.8.0-rc4-syzkaller-00267-g0f1dd5e91e2b #0 Hardware name: Google Google C ---truncated---

In the Linux kernel, the following vulnerability has been resolved: tipc: wait and exit until all work queues are done On some host, a crash could be triggered simply by repeating these commands several times: # modprobe tipc # tipc bearer enable media udp name UDP1 localip 127.0.0.1 # rmmod tipc [] BUG: unable to handle kernel paging request at ffffffffc096bb00 [] Workqueue: events 0xffffffffc096bb00 [] Call Trace: [] ? process_one_work+0x1a7/0x360 [] ? worker_thread+0x30/0x390 [] ? create_worker+0x1a0/0x1a0 [] ? kthread+0x116/0x130 [] ? kthread_flush_work_fn+0x10/0x10 [] ? ret_from_fork+0x35/0x40 When removing the TIPC module, the UDP tunnel sock will be delayed to release in a work queue as sock_release() can't be done in rtnl_lock(). If the work queue is schedule to run after the TIPC module is removed, kernel will crash as the work queue function cleanup_beareri() code no longer exists when trying to invoke it. To fix it, this patch introduce a member wq_count in tipc_net to track the numbers of work queues in schedule, and wait and exit until all work queues are done in tipc_exit_net().

In the Linux kernel, the following vulnerability has been resolved: clk: Get runtime PM before walking tree for clk_summary Similar to the previous commit, we should make sure that all devices are runtime resumed before printing the clk_summary through debugfs. Failure to do so would result in a deadlock if the thread is resuming a device to print clk state and that device is also runtime resuming in another thread, e.g the screen is turning on and the display driver is starting up. We remove the calls to clk_pm_runtime_{get,put}() in this path because they're superfluous now that we know the devices are runtime resumed. This also squashes a bug where the return value of clk_pm_runtime_get() wasn't checked, leading to an RPM count underflow on error paths.

In the Linux kernel, the following vulnerability has been resolved: spi: cadence-qspi: remove system-wide suspend helper calls from runtime PM hooks The ->runtime_suspend() and ->runtime_resume() callbacks are not expected to call spi_controller_suspend() and spi_controller_resume(). Remove calls to those in the cadence-qspi driver. Those helpers have two roles currently: - They stop/start the queue, including dealing with the kworker. - They toggle the SPI controller SPI_CONTROLLER_SUSPENDED flag. It requires acquiring ctlr->bus_lock_mutex. Step one is irrelevant because cadence-qspi is not queued. Step two however has two implications: - A deadlock occurs, because ->runtime_resume() is called in a context where the lock is already taken (in the ->exec_op() callback, where the usage count is incremented). - It would disallow all operations once the device is auto-suspended. Here is a brief call tree highlighting the mutex deadlock: spi_mem_exec_op() ... spi_mem_access_start() mutex_lock(&ctlr->bus_lock_mutex) cqspi_exec_mem_op() pm_runtime_resume_and_get() cqspi_resume() spi_controller_resume() mutex_lock(&ctlr->bus_lock_mutex) ... spi_mem_access_end() mutex_unlock(&ctlr->bus_lock_mutex) ...

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Prevent deadlock while disabling aRFS When disabling aRFS under the `priv->state_lock`, any scheduled aRFS works are canceled using the `cancel_work_sync` function, which waits for the work to end if it has already started. However, while waiting for the work handler, the handler will try to acquire the `state_lock` which is already acquired. The worker acquires the lock to delete the rules if the state is down, which is not the worker's responsibility since disabling aRFS deletes the rules. Add an aRFS state variable, which indicates whether the aRFS is enabled and prevent adding rules when the aRFS is disabled. Kernel log: ====================================================== WARNING: possible circular locking dependency detected 6.7.0-rc4_net_next_mlx5_5483eb2 #1 Tainted: G I ------------------------------------------------------ ethtool/386089 is trying to acquire lock: ffff88810f21ce68 ((work_completion)(&rule->arfs_work)){+.+.}-{0:0}, at: __flush_work+0x74/0x4e0 but task is already holding lock: ffff8884a1808cc0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_ethtool_set_channels+0x53/0x200 [mlx5_core] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&priv->state_lock){+.+.}-{3:3}: __mutex_lock+0x80/0xc90 arfs_handle_work+0x4b/0x3b0 [mlx5_core] process_one_work+0x1dc/0x4a0 worker_thread+0x1bf/0x3c0 kthread+0xd7/0x100 ret_from_fork+0x2d/0x50 ret_from_fork_asm+0x11/0x20 -> #0 ((work_completion)(&rule->arfs_work)){+.+.}-{0:0}: __lock_acquire+0x17b4/0x2c80 lock_acquire+0xd0/0x2b0 __flush_work+0x7a/0x4e0 __cancel_work_timer+0x131/0x1c0 arfs_del_rules+0x143/0x1e0 [mlx5_core] mlx5e_arfs_disable+0x1b/0x30 [mlx5_core] mlx5e_ethtool_set_channels+0xcb/0x200 [mlx5_core] ethnl_set_channels+0x28f/0x3b0 ethnl_default_set_doit+0xec/0x240 genl_family_rcv_msg_doit+0xd0/0x120 genl_rcv_msg+0x188/0x2c0 netlink_rcv_skb+0x54/0x100 genl_rcv+0x24/0x40 netlink_unicast+0x1a1/0x270 netlink_sendmsg+0x214/0x460 __sock_sendmsg+0x38/0x60 __sys_sendto+0x113/0x170 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x40/0xe0 entry_SYSCALL_64_after_hwframe+0x46/0x4e other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&priv->state_lock); lock((work_completion)(&rule->arfs_work)); lock(&priv->state_lock); lock((work_completion)(&rule->arfs_work)); *** DEADLOCK *** 3 locks held by ethtool/386089: #0: ffffffff82ea7210 (cb_lock){++++}-{3:3}, at: genl_rcv+0x15/0x40 #1: ffffffff82e94c88 (rtnl_mutex){+.+.}-{3:3}, at: ethnl_default_set_doit+0xd3/0x240 #2: ffff8884a1808cc0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_ethtool_set_channels+0x53/0x200 [mlx5_core] stack backtrace: CPU: 15 PID: 386089 Comm: ethtool Tainted: G I 6.7.0-rc4_net_next_mlx5_5483eb2 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x60/0xa0 check_noncircular+0x144/0x160 __lock_acquire+0x17b4/0x2c80 lock_acquire+0xd0/0x2b0 ? __flush_work+0x74/0x4e0 ? save_trace+0x3e/0x360 ? __flush_work+0x74/0x4e0 __flush_work+0x7a/0x4e0 ? __flush_work+0x74/0x4e0 ? __lock_acquire+0xa78/0x2c80 ? lock_acquire+0xd0/0x2b0 ? mark_held_locks+0x49/0x70 __cancel_work_timer+0x131/0x1c0 ? mark_held_locks+0x49/0x70 arfs_del_rules+0x143/0x1e0 [mlx5_core] mlx5e_arfs_disable+0x1b/0x30 [mlx5_core] mlx5e_ethtool_set_channels+0xcb/0x200 [mlx5_core] ethnl_set_channels+0x28f/0x3b0 ethnl_default_set_doit+0xec/0x240 genl_family_rcv_msg_doit+0xd0/0x120 genl_rcv_msg+0x188/0x2c0 ? ethn ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net/sched: act_mirred: use the backlog for mirred ingress The test Davide added in commit ca22da2fbd69 ("act_mirred: use the backlog for nested calls to mirred ingress") hangs our testing VMs every 10 or so runs, with the familiar tcp_v4_rcv -> tcp_v4_rcv deadlock reported by lockdep. The problem as previously described by Davide (see Link) is that if we reverse flow of traffic with the redirect (egress -> ingress) we may reach the same socket which generated the packet. And we may still be holding its socket lock. The common solution to such deadlocks is to put the packet in the Rx backlog, rather than run the Rx path inline. Do that for all egress -> ingress reversals, not just once we started to nest mirred calls. In the past there was a concern that the backlog indirection will lead to loss of error reporting / less accurate stats. But the current workaround does not seem to address the issue.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: release mutex after nft_gc_seq_end from abort path The commit mutex should not be released during the critical section between nft_gc_seq_begin() and nft_gc_seq_end(), otherwise, async GC worker could collect expired objects and get the released commit lock within the same GC sequence. nf_tables_module_autoload() temporarily releases the mutex to load module dependencies, then it goes back to replay the transaction again. Move it at the end of the abort phase after nft_gc_seq_end() is called.

In the Linux kernel, the following vulnerability has been resolved: nouveau: offload fence uevents work to workqueue This should break the deadlock between the fctx lock and the irq lock. This offloads the processing off the work from the irq into a workqueue.

In the Linux kernel, the following vulnerability has been resolved: nvme: fix reconnection fail due to reserved tag allocation We found a issue on production environment while using NVMe over RDMA, admin_q reconnect failed forever while remote target and network is ok. After dig into it, we found it may caused by a ABBA deadlock due to tag allocation. In my case, the tag was hold by a keep alive request waiting inside admin_q, as we quiesced admin_q while reset ctrl, so the request maked as idle and will not process before reset success. As fabric_q shares tagset with admin_q, while reconnect remote target, we need a tag for connect command, but the only one reserved tag was held by keep alive command which waiting inside admin_q. As a result, we failed to reconnect admin_q forever. In order to fix this issue, I think we should keep two reserved tags for admin queue.