In the Linux kernel, the following vulnerability has been resolved: LoongArch: KVM: Avoid overflow with array index The variable index is modified and reused as array index when modify register EIOINTC_ENABLE. There will be array index overflow problem.

An integer overflow in the uvesafb_setcmap function in drivers/video/fbdev/uvesafb.c in the Linux kernel before 4.17.4 could result in local attackers being able to crash the kernel or potentially elevate privileges because kmalloc_array is not used.

In the Linux kernel, the following vulnerability has been resolved: jbd2: remove wrong sb->s_sequence check Journal emptiness is not determined by sb->s_sequence == 0 but rather by sb->s_start == 0 (which is set a few lines above). Furthermore 0 is a valid transaction ID so the check can spuriously trigger. Remove the invalid WARN_ON.

In the Linux kernel, the following vulnerability has been resolved: scsi: megaraid_sas: Fix invalid node index On a system with DRAM interleave enabled, out-of-bound access is detected: megaraid_sas 0000:3f:00.0: requested/available msix 128/128 poll_queue 0 ------------[ cut here ]------------ UBSAN: array-index-out-of-bounds in ./arch/x86/include/asm/topology.h:72:28 index -1 is out of range for type 'cpumask *[1024]' dump_stack_lvl+0x5d/0x80 ubsan_epilogue+0x5/0x2b __ubsan_handle_out_of_bounds.cold+0x46/0x4b megasas_alloc_irq_vectors+0x149/0x190 [megaraid_sas] megasas_probe_one.cold+0xa4d/0x189c [megaraid_sas] local_pci_probe+0x42/0x90 pci_device_probe+0xdc/0x290 really_probe+0xdb/0x340 __driver_probe_device+0x78/0x110 driver_probe_device+0x1f/0xa0 __driver_attach+0xba/0x1c0 bus_for_each_dev+0x8b/0xe0 bus_add_driver+0x142/0x220 driver_register+0x72/0xd0 megasas_init+0xdf/0xff0 [megaraid_sas] do_one_initcall+0x57/0x310 do_init_module+0x90/0x250 init_module_from_file+0x85/0xc0 idempotent_init_module+0x114/0x310 __x64_sys_finit_module+0x65/0xc0 do_syscall_64+0x82/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e Fix it accordingly.

In the Linux kernel, the following vulnerability has been resolved: scsi: smartpqi: Fix smp_processor_id() call trace for preemptible kernels Correct kernel call trace when calling smp_processor_id() when called in preemptible kernels by using raw_smp_processor_id(). smp_processor_id() checks to see if preemption is disabled and if not, issue an error message followed by a call to dump_stack(). Brief example of call trace: kernel: check_preemption_disabled: 436 callbacks suppressed kernel: BUG: using smp_processor_id() in preemptible [00000000] code: kworker/u1025:0/2354 kernel: caller is pqi_scsi_queue_command+0x183/0x310 [smartpqi] kernel: CPU: 129 PID: 2354 Comm: kworker/u1025:0 kernel: ... kernel: Workqueue: writeback wb_workfn (flush-253:0) kernel: Call Trace: kernel: <TASK> kernel: dump_stack_lvl+0x34/0x48 kernel: check_preemption_disabled+0xdd/0xe0 kernel: pqi_scsi_queue_command+0x183/0x310 [smartpqi] kernel: ...

In the Linux kernel, the following vulnerability has been resolved: bus: fsl-mc: fix double-free on mc_dev The blamed commit tried to simplify how the deallocations are done but, in the process, introduced a double-free on the mc_dev variable. In case the MC device is a DPRC, a new mc_bus is allocated and the mc_dev variable is just a reference to one of its fields. In this circumstance, on the error path only the mc_bus should be freed. This commit introduces back the following checkpatch warning which is a false-positive. WARNING: kfree(NULL) is safe and this check is probably not required + if (mc_bus) + kfree(mc_bus);

In the Linux kernel, the following vulnerability has been resolved: scsi: smartpqi: Use is_kdump_kernel() to check for kdump The smartpqi driver checks the reset_devices variable to determine whether special adjustments need to be made for kdump. This has the effect that after a regular kexec reboot, some driver parameters such as max_transfer_size are much lower than usual. More importantly, kexec reboot tests have revealed memory corruption caused by the driver log being written to system memory after a kexec. Fix this by testing is_kdump_kernel() rather than reset_devices where appropriate.

The inode_init_owner function in fs/inode.c in the Linux kernel through 3.16 allows local users to create files with an unintended group ownership, in a scenario where a directory is SGID to a certain group and is writable by a user who is not a member of that group. Here, the non-member can trigger creation of a plain file whose group ownership is that group. The intended behavior was that the non-member can trigger creation of a directory (but not a plain file) whose group ownership is that group. The non-member can escalate privileges by making the plain file executable and SGID.

Certain WithSecure products allow Local privilege escalation via the lhz archive unpack handler. This affects WithSecure Client Security 15, WithSecure Server Security 15, WithSecure Email and Server Security 15, WithSecure Elements Endpoint Protection 17 and later, WithSecure Client Security for Mac 15, WithSecure Elements Endpoint Protection for Mac 17 and later, Linux Security 64 12.0 , Linux Protection 12.0, and WithSecure Atlant (formerly F-Secure Atlant) 1.0.35-1.

In the Linux kernel, the following vulnerability has been resolved: ovl: Filter invalid inodes with missing lookup function Add a check to the ovl_dentry_weird() function to prevent the processing of directory inodes that lack the lookup function. This is important because such inodes can cause errors in overlayfs when passed to the lowerstack.

Vasion Print (formerly PrinterLogic) Virtual Appliance Host versions prior to 1.0.735 and Application versions prior to 20.0.1330 (macOS/Linux client deployments) contain a vulnerability in the local inter-process communication (IPC) mechanism. The software stores IPC request and response files inside /opt/PrinterInstallerClient/tmp with world-readable and world-writable permissions. Any local user can craft malicious request files that are processed by privileged daemons, leading to unauthorized actions being executed in other user sessions. This breaks user session isolation, potentially allowing local attackers to hijack sessions, perform unintended actions in the context of other users, and impact system integrity and availability. This vulnerability has been identified by the vendor as: V-2022-004 — Client Inter-process Security.

Vasion Print (formerly PrinterLogic) Virtual Appliance Host versions prior to 25.1.102 and Application versions prior to 25.1.1413 (macOS/Linux client deployments) are vulnerable to an authentication bypass in PrinterInstallerClientService. The service requires root privileges for certain administrative operations, but these checks rely on calls to geteuid(). By preloading a malicious shared object overriding geteuid(), a local attacker can trick the service into believing it is running with root privileges. This bypass enables execution of administrative commands (e.g., enabling debug mode, managing configurations, or invoking privileged features) without proper authorization. While some actions requiring write access to protected files may still fail, the flaw effectively breaks the intended security model of the inter-process communication (IPC) system, allowing local attackers to escalate privileges and compromise system integrity. This vulnerability has been confirmed to be remediated, but it is unclear as to when the patch was introduced.

Vasion Print (formerly PrinterLogic) Virtual Appliance Host versions prior to 1.0.735 and Application prior to 20.0.1330 (macOS/Linux client deployments) contain a vulnerability in the local logging mechanism. Authentication session tokens, including PHPSESSID, XSRF-TOKEN, and laravel_session, are stored in cleartext within world-readable log files. Any local user with access to the machine can extract these session tokens and use them to authenticate remotely to the SaaS environment, bypassing normal login credentials, potentially leading to unauthorized system access and exposure of sensitive information. This vulnerability has been identified by the vendor as: V-2022-008 — Secrets Leaked in Logs.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Skip inactive planes within ModeSupportAndSystemConfiguration [Why] Coverity reports Memory - illegal accesses. [How] Skip inactive planes.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check link_index before accessing dc->links[] [WHY & HOW] dc->links[] has max size of MAX_LINKS and NULL is return when trying to access with out-of-bound index. This fixes 3 OVERRUN and 1 RESOURCE_LEAK issues reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: bpf: fix OOB devmap writes when deleting elements Jordy reported issue against XSKMAP which also applies to DEVMAP - the index used for accessing map entry, due to being a signed integer, causes the OOB writes. Fix is simple as changing the type from int to u32, however, when compared to XSKMAP case, one more thing needs to be addressed. When map is released from system via dev_map_free(), we iterate through all of the entries and an iterator variable is also an int, which implies OOB accesses. Again, change it to be u32. Example splat below: [ 160.724676] BUG: unable to handle page fault for address: ffffc8fc2c001000 [ 160.731662] #PF: supervisor read access in kernel mode [ 160.736876] #PF: error_code(0x0000) - not-present page [ 160.742095] PGD 0 P4D 0 [ 160.744678] Oops: Oops: 0000 [#1] PREEMPT SMP [ 160.749106] CPU: 1 UID: 0 PID: 520 Comm: kworker/u145:12 Not tainted 6.12.0-rc1+ #487 [ 160.757050] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019 [ 160.767642] Workqueue: events_unbound bpf_map_free_deferred [ 160.773308] RIP: 0010:dev_map_free+0x77/0x170 [ 160.777735] Code: 00 e8 fd 91 ed ff e8 b8 73 ed ff 41 83 7d 18 19 74 6e 41 8b 45 24 49 8b bd f8 00 00 00 31 db 85 c0 74 48 48 63 c3 48 8d 04 c7 <48> 8b 28 48 85 ed 74 30 48 8b 7d 18 48 85 ff 74 05 e8 b3 52 fa ff [ 160.796777] RSP: 0018:ffffc9000ee1fe38 EFLAGS: 00010202 [ 160.802086] RAX: ffffc8fc2c001000 RBX: 0000000080000000 RCX: 0000000000000024 [ 160.809331] RDX: 0000000000000000 RSI: 0000000000000024 RDI: ffffc9002c001000 [ 160.816576] RBP: 0000000000000000 R08: 0000000000000023 R09: 0000000000000001 [ 160.823823] R10: 0000000000000001 R11: 00000000000ee6b2 R12: dead000000000122 [ 160.831066] R13: ffff88810c928e00 R14: ffff8881002df405 R15: 0000000000000000 [ 160.838310] FS: 0000000000000000(0000) GS:ffff8897e0c40000(0000) knlGS:0000000000000000 [ 160.846528] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 160.852357] CR2: ffffc8fc2c001000 CR3: 0000000005c32006 CR4: 00000000007726f0 [ 160.859604] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 160.866847] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 160.874092] PKRU: 55555554 [ 160.876847] Call Trace: [ 160.879338] <TASK> [ 160.881477] ? __die+0x20/0x60 [ 160.884586] ? page_fault_oops+0x15a/0x450 [ 160.888746] ? search_extable+0x22/0x30 [ 160.892647] ? search_bpf_extables+0x5f/0x80 [ 160.896988] ? exc_page_fault+0xa9/0x140 [ 160.900973] ? asm_exc_page_fault+0x22/0x30 [ 160.905232] ? dev_map_free+0x77/0x170 [ 160.909043] ? dev_map_free+0x58/0x170 [ 160.912857] bpf_map_free_deferred+0x51/0x90 [ 160.917196] process_one_work+0x142/0x370 [ 160.921272] worker_thread+0x29e/0x3b0 [ 160.925082] ? rescuer_thread+0x4b0/0x4b0 [ 160.929157] kthread+0xd4/0x110 [ 160.932355] ? kthread_park+0x80/0x80 [ 160.936079] ret_from_fork+0x2d/0x50 [ 160.943396] ? kthread_park+0x80/0x80 [ 160.950803] ret_from_fork_asm+0x11/0x20 [ 160.958482] </TASK>

The sr_do_ioctl function in drivers/scsi/sr_ioctl.c in the Linux kernel through 4.16.12 allows local users to cause a denial of service (stack-based buffer overflow) or possibly have unspecified other impact because sense buffers have different sizes at the CDROM layer and the SCSI layer, as demonstrated by a CDROMREADMODE2 ioctl call.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Add array index check for hdcp ddc access [Why] Coverity reports OVERRUN warning. Do not check if array index valid. [How] Check msg_id valid and valid array index.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix double put of @cfile in smb2_rename_path() If smb2_set_path_attr() is called with a valid @cfile and returned -EINVAL, we need to call cifs_get_writable_path() again as the reference of @cfile was already dropped by previous smb2_compound_op() call.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Fix tainted pointer delete is case of flow rules creation fail In case of flow rule creation fail in mlx5_lag_create_port_sel_table(), instead of previously created rules, the tainted pointer is deleted deveral times. Fix this bug by using correct flow rules pointers. Found by Linux Verification Center (linuxtesting.org) with SVACE.

A flaw was found in Linux kernel's KVM virtualization subsystem. The VMX code does not restore the GDT.LIMIT to the previous host value, but instead sets it to 64KB. With a corrupted GDT limit a host's userspace code has an ability to place malicious entries in the GDT, particularly to the per-cpu variables. An attacker can use this to escalate their privileges.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check gpio_id before used as array index [WHY & HOW] GPIO_ID_UNKNOWN (-1) is not a valid value for array index and therefore should be checked in advance. This fixes 5 OVERRUN issues reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/vcn: remove irq disabling in vcn 5 suspend We do not directly enable/disable VCN IRQ in vcn 5.0.0. And we do not handle the IRQ state as well. So the calls to disable IRQ and set state are removed. This effectively gets rid of the warining of "WARN_ON(!amdgpu_irq_enabled(adev, src, type))" in amdgpu_irq_put().

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix index may exceed array range within fpu_update_bw_bounding_box [Why] Coverity reports OVERRUN warning. soc.num_states could be 40. But array range of bw_params->clk_table.entries is 8. [How] Assert if soc.num_states greater than 8.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: aspeed_udc: validate endpoint index for ast udc We should verify the bound of the array to assure that host may not manipulate the index to point past endpoint array. Found by static analysis.

A flaw was found in the Linux kernel's ext4 filesystem. A local user can cause an out-of-bounds write and a denial of service or unspecified other impact is possible by mounting and operating a crafted ext4 filesystem image.

In the Linux kernel, the following vulnerability has been resolved: Squashfs: sanity check symbolic link size Syzkiller reports a "KMSAN: uninit-value in pick_link" bug. This is caused by an uninitialised page, which is ultimately caused by a corrupted symbolic link size read from disk. The reason why the corrupted symlink size causes an uninitialised page is due to the following sequence of events: 1. squashfs_read_inode() is called to read the symbolic link from disk. This assigns the corrupted value 3875536935 to inode->i_size. 2. Later squashfs_symlink_read_folio() is called, which assigns this corrupted value to the length variable, which being a signed int, overflows producing a negative number. 3. The following loop that fills in the page contents checks that the copied bytes is less than length, which being negative means the loop is skipped, producing an uninitialised page. This patch adds a sanity check which checks that the symbolic link size is not larger than expected. -- V2: fix spelling mistake.

In the Linux kernel, the following vulnerability has been resolved: wifi: prevent A-MSDU attacks in mesh networks This patch is a mitigation to prevent the A-MSDU spoofing vulnerability for mesh networks. The initial update to the IEEE 802.11 standard, in response to the FragAttacks, missed this case (CVE-2025-27558). It can be considered a variant of CVE-2020-24588 but for mesh networks. This patch tries to detect if a standard MSDU was turned into an A-MSDU by an adversary. This is done by parsing a received A-MSDU as a standard MSDU, calculating the length of the Mesh Control header, and seeing if the 6 bytes after this header equal the start of an rfc1042 header. If equal, this is a strong indication of an ongoing attack attempt. This defense was tested with mac80211_hwsim against a mesh network that uses an empty Mesh Address Extension field, i.e., when four addresses are used, and when using a 12-byte Mesh Address Extension field, i.e., when six addresses are used. Functionality of normal MSDUs and A-MSDUs was also tested, and confirmed working, when using both an empty and 12-byte Mesh Address Extension field. It was also tested with mac80211_hwsim that A-MSDU attacks in non-mesh networks keep being detected and prevented. Note that the vulnerability being patched, and the defense being implemented, was also discussed in the following paper and in the following IEEE 802.11 presentation: https://papers.mathyvanhoef.com/wisec2025.pdf https://mentor.ieee.org/802.11/dcn/25/11-25-0949-00-000m-a-msdu-mesh-spoof-protection.docx

An issue was discovered the x86 KVM subsystem in the Linux kernel before 5.18.17. Unprivileged guest users can compromise the guest kernel because TLB flush operations are mishandled in certain KVM_VCPU_PREEMPTED situations.

In the Linux kernel, the following vulnerability has been resolved: um: line: always fill *error_out in setup_one_line() The pointer isn't initialized by callers, but I have encountered cases where it's still printed; initialize it in all possible cases in setup_one_line().

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Correct the defined value for AMDGPU_DMUB_NOTIFICATION_MAX [Why & How] It actually exposes '6' types in enum dmub_notification_type. Not 5. Using smaller number to create array dmub_callback & dmub_thread_offload has potential to access item out of array bound. Fix it.

In the Linux kernel, the following vulnerability has been resolved: net: hns3: void array out of bound when loop tnl_num When query reg inf of SSU, it loops tnl_num times. However, tnl_num comes from hardware and the length of array is a fixed value. To void array out of bound, make sure the loop time is not greater than the length of array

The KEYS subsystem in the Linux kernel before 4.13.10 does not correctly synchronize the actions of updating versus finding a key in the "negative" state to avoid a race condition, which allows local users to cause a denial of service or possibly have unspecified other impact via crafted system calls.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/pm: Fix negative array index read Avoid using the negative values for clk_idex as an index into an array pptable->DpmDescriptor. V2: fix clk_index return check (Tim Huang)

NVIDIA NeMo library for all platforms contains a vulnerability in the model loading component, where an attacker could cause code injection by loading .nemo files with maliciously crafted metadata. A successful exploit of this vulnerability may lead to remote code execution and data tampering.

NVIDIA NeMo Framework for all platforms contains a vulnerability where a user could cause a deserialization of untrusted data by remote code execution. A successful exploit of this vulnerability might lead to code execution and data tampering.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check num_valid_sets before accessing reader_wm_sets[] [WHY & HOW] num_valid_sets needs to be checked to avoid a negative index when accessing reader_wm_sets[num_valid_sets - 1]. This fixes an OVERRUN issue reported by Coverity.

NVIDIA NeMo Framework for all platforms contains a vulnerability in the export and deploy component, where malicious data created by an attacker could cause a code injection issue. A successful exploit of this vulnerability might lead to code execution, escalation of privileges, information disclosure, and data tampering.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: update channel list in reg notifier instead reg worker Currently when ath11k gets a new channel list, it will be processed according to the following steps: 1. update new channel list to cfg80211 and queue reg_work. 2. cfg80211 handles new channel list during reg_work. 3. update cfg80211's handled channel list to firmware by ath11k_reg_update_chan_list(). But ath11k will immediately execute step 3 after reg_work is just queued. Since step 2 is asynchronous, cfg80211 may not have completed handling the new channel list, which may leading to an out-of-bounds write error: BUG: KASAN: slab-out-of-bounds in ath11k_reg_update_chan_list Call Trace: ath11k_reg_update_chan_list+0xbfe/0xfe0 [ath11k] kfree+0x109/0x3a0 ath11k_regd_update+0x1cf/0x350 [ath11k] ath11k_regd_update_work+0x14/0x20 [ath11k] process_one_work+0xe35/0x14c0 Should ensure step 2 is completely done before executing step 3. Thus Wen raised patch[1]. When flag NL80211_REGDOM_SET_BY_DRIVER is set, cfg80211 will notify ath11k after step 2 is done. So enable the flag NL80211_REGDOM_SET_BY_DRIVER then cfg80211 will notify ath11k after step 2 is done. At this time, there will be no KASAN bug during the execution of the step 3. [1] https://patchwork.kernel.org/project/linux-wireless/patch/20230201065313.27203-1-quic_wgong@quicinc.com/ Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

In the Linux kernel, the following vulnerability has been resolved: scsi: smartpqi: Fix disable_managed_interrupts Correct blk-mq registration issue with module parameter disable_managed_interrupts enabled. When we turn off the default PCI_IRQ_AFFINITY flag, the driver needs to register with blk-mq using blk_mq_map_queues(). The driver is currently calling blk_mq_pci_map_queues() which results in a stack trace and possibly undefined behavior. Stack Trace: [ 7.860089] scsi host2: smartpqi [ 7.871934] WARNING: CPU: 0 PID: 238 at block/blk-mq-pci.c:52 blk_mq_pci_map_queues+0xca/0xd0 [ 7.889231] Modules linked in: sd_mod t10_pi sg uas smartpqi(+) crc32c_intel scsi_transport_sas usb_storage dm_mirror dm_region_hash dm_log dm_mod ipmi_devintf ipmi_msghandler fuse [ 7.924755] CPU: 0 PID: 238 Comm: kworker/0:3 Not tainted 4.18.0-372.88.1.el8_6_smartpqi_test.x86_64 #1 [ 7.944336] Hardware name: HPE ProLiant DL380 Gen10/ProLiant DL380 Gen10, BIOS U30 03/08/2022 [ 7.963026] Workqueue: events work_for_cpu_fn [ 7.978275] RIP: 0010:blk_mq_pci_map_queues+0xca/0xd0 [ 7.978278] Code: 48 89 de 89 c7 e8 f6 0f 4f 00 3b 05 c4 b7 8e 01 72 e1 5b 31 c0 5d 41 5c 41 5d 41 5e 41 5f e9 7d df 73 00 31 c0 e9 76 df 73 00 <0f> 0b eb bc 90 90 0f 1f 44 00 00 41 57 49 89 ff 41 56 41 55 41 54 [ 7.978280] RSP: 0018:ffffa95fc3707d50 EFLAGS: 00010216 [ 7.978283] RAX: 00000000ffffffff RBX: 0000000000000000 RCX: 0000000000000010 [ 7.978284] RDX: 0000000000000004 RSI: 0000000000000000 RDI: ffff9190c32d4310 [ 7.978286] RBP: 0000000000000000 R08: ffffa95fc3707d38 R09: ffff91929b81ac00 [ 7.978287] R10: 0000000000000001 R11: ffffa95fc3707ac0 R12: 0000000000000000 [ 7.978288] R13: ffff9190c32d4000 R14: 00000000ffffffff R15: ffff9190c4c950a8 [ 7.978290] FS: 0000000000000000(0000) GS:ffff9193efc00000(0000) knlGS:0000000000000000 [ 7.978292] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 8.172814] CR2: 000055d11166c000 CR3: 00000002dae10002 CR4: 00000000007706f0 [ 8.172816] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 8.172817] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 8.172818] PKRU: 55555554 [ 8.172819] Call Trace: [ 8.172823] blk_mq_alloc_tag_set+0x12e/0x310 [ 8.264339] scsi_add_host_with_dma.cold.9+0x30/0x245 [ 8.279302] pqi_ctrl_init+0xacf/0xc8e [smartpqi] [ 8.294085] ? pqi_pci_probe+0x480/0x4c8 [smartpqi] [ 8.309015] pqi_pci_probe+0x480/0x4c8 [smartpqi] [ 8.323286] local_pci_probe+0x42/0x80 [ 8.337855] work_for_cpu_fn+0x16/0x20 [ 8.351193] process_one_work+0x1a7/0x360 [ 8.364462] ? create_worker+0x1a0/0x1a0 [ 8.379252] worker_thread+0x1ce/0x390 [ 8.392623] ? create_worker+0x1a0/0x1a0 [ 8.406295] kthread+0x10a/0x120 [ 8.418428] ? set_kthread_struct+0x50/0x50 [ 8.431532] ret_from_fork+0x1f/0x40 [ 8.444137] ---[ end trace 1bf0173d39354506 ]---

Buffer overflow in the mp_override_legacy_irq() function in arch/x86/kernel/acpi/boot.c in the Linux kernel through 3.2 allows local users to gain privileges via a crafted ACPI table.

In the Linux kernel, the following vulnerability has been resolved: mm: use aligned address in clear_gigantic_page() In current kernel, hugetlb_no_page() calls folio_zero_user() with the fault address. Where the fault address may be not aligned with the huge page size. Then, folio_zero_user() may call clear_gigantic_page() with the address, while clear_gigantic_page() requires the address to be huge page size aligned. So, this may cause memory corruption or information leak, addtional, use more obvious naming 'addr_hint' instead of 'addr' for clear_gigantic_page().

The sanity_check_ckpt function in fs/f2fs/super.c in the Linux kernel before 4.12.4 does not validate the blkoff and segno arrays, which allows local users to gain privileges via unspecified vectors.

The sanity_check_raw_super function in fs/f2fs/super.c in the Linux kernel before 4.11.1 does not validate the segment count, which allows local users to gain privileges via unspecified vectors.

The offset2lib patch as used by the Linux Kernel contains a vulnerability, if RLIMIT_STACK is set to RLIM_INFINITY and 1 Gigabyte of memory is allocated (the maximum under the 1/4 restriction) then the stack will be grown down to 0x80000000, and as the PIE binary is mapped above 0x80000000 the minimum distance between the end of the PIE binary's read-write segment and the start of the stack becomes small enough that the stack guard page can be jumped over by an attacker. This affects Linux Kernel version 4.11.5. This is a different issue than CVE-2017-1000370 and CVE-2017-1000365. This issue appears to be limited to i386 based systems.

Linux distributions that have not patched their long-term kernels with https://git.kernel.org/linus/a87938b2e246b81b4fb713edb371a9fa3c5c3c86 (committed on April 14, 2015). This kernel vulnerability was fixed in April 2015 by commit a87938b2e246b81b4fb713edb371a9fa3c5c3c86 (backported to Linux 3.10.77 in May 2015), but it was not recognized as a security threat. With CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE enabled, and a normal top-down address allocation strategy, load_elf_binary() will attempt to map a PIE binary into an address range immediately below mm->mmap_base. Unfortunately, load_elf_ binary() does not take account of the need to allocate sufficient space for the entire binary which means that, while the first PT_LOAD segment is mapped below mm->mmap_base, the subsequent PT_LOAD segment(s) end up being mapped above mm->mmap_base into the are that is supposed to be the "gap" between the stack and the binary.

NVIDIA GPU Display Driver for Linux contains a vulnerability in the kernel mode layer handler, where an unprivileged regular user can cause truncation errors when casting a primitive to a primitive of smaller size causes data to be lost in the conversion, which may lead to denial of service or information disclosure.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check msg_id before processing transcation [WHY & HOW] HDCP_MESSAGE_ID_INVALID (-1) is not a valid msg_id nor is it a valid array index, and it needs checking before used. This fixes 4 OVERRUN issues reported by Coverity.

The Linux Kernel imposes a size restriction on the arguments and environmental strings passed through RLIMIT_STACK/RLIM_INFINITY (1/4 of the size), but does not take the argument and environment pointers into account, which allows attackers to bypass this limitation. This affects Linux Kernel versions 4.11.5 and earlier. It appears that this feature was introduced in the Linux Kernel version 2.6.23.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix out-of-bounds write warning Check the ring type value to fix the out-of-bounds write warning