In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: don't allow mapping the MMIO HDP page with large pages We don't get the right offset in that case. The GPU has an unused 4K area of the register BAR space into which you can remap registers. We remap the HDP flush registers into this space to allow userspace (CPU or GPU) to flush the HDP when it updates VRAM. However, on systems with >4K pages, we end up exposing PAGE_SIZE of MMIO space.

An integer overflow flaw was found in the Linux kernel’s virtio device driver code in the way a user triggers the vhost_vdpa_config_validate function. This flaw allows a local user to crash or potentially escalate their privileges on the system.

In the Linux kernel, the following vulnerability has been resolved: comedi: vmk80xx: fix transfer-buffer overflows The driver uses endpoint-sized USB transfer buffers but up until recently had no sanity checks on the sizes. Commit e1f13c879a7c ("staging: comedi: check validity of wMaxPacketSize of usb endpoints found") inadvertently fixed NULL-pointer dereferences when accessing the transfer buffers in case a malicious device has a zero wMaxPacketSize. Make sure to allocate buffers large enough to handle also the other accesses that are done without a size check (e.g. byte 18 in vmk80xx_cnt_insn_read() for the VMK8061_MODEL) to avoid writing beyond the buffers, for example, when doing descriptor fuzzing. The original driver was for a low-speed device with 8-byte buffers. Support was later added for a device that uses bulk transfers and is presumably a full-speed device with a maximum 64-byte wMaxPacketSize.

In the Linux kernel, the following vulnerability has been resolved: comedi: dt9812: fix DMA buffers on stack USB transfer buffers are typically mapped for DMA and must not be allocated on the stack or transfers will fail. Allocate proper transfer buffers in the various command helpers and return an error on short transfers instead of acting on random stack data. Note that this also fixes a stack info leak on systems where DMA is not used as 32 bytes are always sent to the device regardless of how short the command is.

In the Linux kernel, the following vulnerability has been resolved: video: fbdev: nvidiafb: Use strscpy() to prevent buffer overflow Coverity complains of a possible buffer overflow. However, given the 'static' scope of nvidia_setup_i2c_bus() it looks like that can't happen after examiniing the call sites. CID 19036 (#1 of 1): Copy into fixed size buffer (STRING_OVERFLOW) 1. fixed_size_dest: You might overrun the 48-character fixed-size string chan->adapter.name by copying name without checking the length. 2. parameter_as_source: Note: This defect has an elevated risk because the source argument is a parameter of the current function. 89 strcpy(chan->adapter.name, name); Fix this warning by using strscpy() which will silence the warning and prevent any future buffer overflows should the names used to identify the channel become much longer.

In the Linux kernel, the following vulnerability has been resolved: regmap: Fix possible double-free in regcache_rbtree_exit() In regcache_rbtree_insert_to_block(), when 'present' realloc failed, the 'blk' which is supposed to assign to 'rbnode->block' will be freed, so 'rbnode->block' points a freed memory, in the error handling path of regcache_rbtree_init(), 'rbnode->block' will be freed again in regcache_rbtree_exit(), KASAN will report double-free as follows: BUG: KASAN: double-free or invalid-free in kfree+0xce/0x390 Call Trace: slab_free_freelist_hook+0x10d/0x240 kfree+0xce/0x390 regcache_rbtree_exit+0x15d/0x1a0 regcache_rbtree_init+0x224/0x2c0 regcache_init+0x88d/0x1310 __regmap_init+0x3151/0x4a80 __devm_regmap_init+0x7d/0x100 madera_spi_probe+0x10f/0x333 [madera_spi] spi_probe+0x183/0x210 really_probe+0x285/0xc30 To fix this, moving up the assignment of rbnode->block to immediately after the reallocation has succeeded so that the data structure stays valid even if the second reallocation fails.

A random memory access flaw was found in the Linux kernel's GPU i915 kernel driver functionality in the way a user may run malicious code on the GPU. This flaw allows a local user to crash the system or escalate their privileges on the system.

A vulnerability was found in the Linux kernel’s cgroup_release_agent_write in the kernel/cgroup/cgroup-v1.c function. This flaw, under certain circumstances, allows the use of the cgroups v1 release_agent feature to escalate privileges and bypass the namespace isolation unexpectedly.

In the Linux kernel, the following vulnerability has been resolved: drm: zynqmp_dpsub: Always register bridge We must always register the DRM bridge, since zynqmp_dp_hpd_work_func calls drm_bridge_hpd_notify, which in turn expects hpd_mutex to be initialized. We do this before zynqmp_dpsub_drm_init since that calls drm_bridge_attach. This fixes the following lockdep warning: [ 19.217084] ------------[ cut here ]------------ [ 19.227530] DEBUG_LOCKS_WARN_ON(lock->magic != lock) [ 19.227768] WARNING: CPU: 0 PID: 140 at kernel/locking/mutex.c:582 __mutex_lock+0x4bc/0x550 [ 19.241696] Modules linked in: [ 19.244937] CPU: 0 PID: 140 Comm: kworker/0:4 Not tainted 6.6.20+ #96 [ 19.252046] Hardware name: xlnx,zynqmp (DT) [ 19.256421] Workqueue: events zynqmp_dp_hpd_work_func [ 19.261795] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 19.269104] pc : __mutex_lock+0x4bc/0x550 [ 19.273364] lr : __mutex_lock+0x4bc/0x550 [ 19.277592] sp : ffffffc085c5bbe0 [ 19.281066] x29: ffffffc085c5bbe0 x28: 0000000000000000 x27: ffffff88009417f8 [ 19.288624] x26: ffffff8800941788 x25: ffffff8800020008 x24: ffffffc082aa3000 [ 19.296227] x23: ffffffc080d90e3c x22: 0000000000000002 x21: 0000000000000000 [ 19.303744] x20: 0000000000000000 x19: ffffff88002f5210 x18: 0000000000000000 [ 19.311295] x17: 6c707369642e3030 x16: 3030613464662072 x15: 0720072007200720 [ 19.318922] x14: 0000000000000000 x13: 284e4f5f4e524157 x12: 0000000000000001 [ 19.326442] x11: 0001ffc085c5b940 x10: 0001ff88003f388b x9 : 0001ff88003f3888 [ 19.334003] x8 : 0001ff88003f3888 x7 : 0000000000000000 x6 : 0000000000000000 [ 19.341537] x5 : 0000000000000000 x4 : 0000000000001668 x3 : 0000000000000000 [ 19.349054] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffffff88003f3880 [ 19.356581] Call trace: [ 19.359160] __mutex_lock+0x4bc/0x550 [ 19.363032] mutex_lock_nested+0x24/0x30 [ 19.367187] drm_bridge_hpd_notify+0x2c/0x6c [ 19.371698] zynqmp_dp_hpd_work_func+0x44/0x54 [ 19.376364] process_one_work+0x3ac/0x988 [ 19.380660] worker_thread+0x398/0x694 [ 19.384736] kthread+0x1bc/0x1c0 [ 19.388241] ret_from_fork+0x10/0x20 [ 19.392031] irq event stamp: 183 [ 19.395450] hardirqs last enabled at (183): [<ffffffc0800b9278>] finish_task_switch.isra.0+0xa8/0x2d4 [ 19.405140] hardirqs last disabled at (182): [<ffffffc081ad3754>] __schedule+0x714/0xd04 [ 19.413612] softirqs last enabled at (114): [<ffffffc080133de8>] srcu_invoke_callbacks+0x158/0x23c [ 19.423128] softirqs last disabled at (110): [<ffffffc080133de8>] srcu_invoke_callbacks+0x158/0x23c [ 19.432614] ---[ end trace 0000000000000000 ]--- (cherry picked from commit 61ba791c4a7a09a370c45b70a81b8c7d4cf6b2ae)

In the Linux kernel, the following vulnerability has been resolved: net/tls: Fix flipped sign in tls_err_abort() calls sk->sk_err appears to expect a positive value, a convention that ktls doesn't always follow and that leads to memory corruption in other code. For instance, [kworker] tls_encrypt_done(..., err=<negative error from crypto request>) tls_err_abort(.., err) sk->sk_err = err; [task] splice_from_pipe_feed ... tls_sw_do_sendpage if (sk->sk_err) { ret = -sk->sk_err; // ret is positive splice_from_pipe_feed (continued) ret = actor(...) // ret is still positive and interpreted as bytes // written, resulting in underflow of buf->len and // sd->len, leading to huge buf->offset and bogus // addresses computed in later calls to actor() Fix all tls_err_abort() callers to pass a negative error code consistently and centralize the error-prone sign flip there, throwing in a warning to catch future misuse and uninlining the function so it really does only warn once.

In the Linux kernel, the following vulnerability has been resolved: dma-mapping: benchmark: handle NUMA_NO_NODE correctly cpumask_of_node() can be called for NUMA_NO_NODE inside do_map_benchmark() resulting in the following sanitizer report: UBSAN: array-index-out-of-bounds in ./arch/x86/include/asm/topology.h:72:28 index -1 is out of range for type 'cpumask [64][1]' CPU: 1 PID: 990 Comm: dma_map_benchma Not tainted 6.9.0-rc6 #29 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:117) ubsan_epilogue (lib/ubsan.c:232) __ubsan_handle_out_of_bounds (lib/ubsan.c:429) cpumask_of_node (arch/x86/include/asm/topology.h:72) [inline] do_map_benchmark (kernel/dma/map_benchmark.c:104) map_benchmark_ioctl (kernel/dma/map_benchmark.c:246) full_proxy_unlocked_ioctl (fs/debugfs/file.c:333) __x64_sys_ioctl (fs/ioctl.c:890) do_syscall_64 (arch/x86/entry/common.c:83) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) Use cpumask_of_node() in place when binding a kernel thread to a cpuset of a particular node. Note that the provided node id is checked inside map_benchmark_ioctl(). It's just a NUMA_NO_NODE case which is not handled properly later. Found by Linux Verification Center (linuxtesting.org).

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix even more out of bound writes from debugfs CVE-2021-42327 was fixed by: commit f23750b5b3d98653b31d4469592935ef6364ad67 Author: Thelford Williams <tdwilliamsiv@gmail.com> Date: Wed Oct 13 16:04:13 2021 -0400 drm/amdgpu: fix out of bounds write but amdgpu_dm_debugfs.c contains more of the same issue so fix the remaining ones. v2: * Add missing fix in dp_max_bpc_write (Harry Wentland)

The cifs_close function in fs/cifs/file.c in the Linux kernel before 2.6.39 allows local users to cause a denial of service (NULL pointer dereference and BUG) or possibly have unspecified other impact by setting the O_DIRECT flag during an attempt to open a file on a CIFS filesystem.

In the Linux kernel, the following vulnerability has been resolved: net: marvell: prestera: fix double free issue on err path fix error path handling in prestera_bridge_port_join() that cases prestera driver to crash (see below). Trace: Internal error: Oops: 96000044 [#1] SMP Modules linked in: prestera_pci prestera uio_pdrv_genirq CPU: 1 PID: 881 Comm: ip Not tainted 5.15.0 #1 pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : prestera_bridge_destroy+0x2c/0xb0 [prestera] lr : prestera_bridge_port_join+0x2cc/0x350 [prestera] sp : ffff800011a1b0f0 ... x2 : ffff000109ca6c80 x1 : dead000000000100 x0 : dead000000000122 Call trace: prestera_bridge_destroy+0x2c/0xb0 [prestera] prestera_bridge_port_join+0x2cc/0x350 [prestera] prestera_netdev_port_event.constprop.0+0x3c4/0x450 [prestera] prestera_netdev_event_handler+0xf4/0x110 [prestera] raw_notifier_call_chain+0x54/0x80 call_netdevice_notifiers_info+0x54/0xa0 __netdev_upper_dev_link+0x19c/0x380

In the Linux kernel, the following vulnerability has been resolved: iio: adc: PAC1934: fix accessing out of bounds array index Fix accessing out of bounds array index for average current and voltage measurements. The device itself has only 4 channels, but in sysfs there are "fake" channels for the average voltages and currents too.

In the Linux kernel, the following vulnerability has been resolved: i2c: virtio: fix completion handling The driver currently assumes that the notify callback is only received when the device is done with all the queued buffers. However, this is not true, since the notify callback could be called without any of the queued buffers being completed (for example, with virtio-pci and shared interrupts) or with only some of the buffers being completed (since the driver makes them available to the device in multiple separate virtqueue_add_sgs() calls). This can lead to incorrect data on the I2C bus or memory corruption in the guest if the device operates on buffers which are have been freed by the driver. (The WARN_ON in the driver is also triggered.) BUG kmalloc-128 (Tainted: G W ): Poison overwritten First byte 0x0 instead of 0x6b Allocated in i2cdev_ioctl_rdwr+0x9d/0x1de age=243 cpu=0 pid=28 memdup_user+0x2e/0xbd i2cdev_ioctl_rdwr+0x9d/0x1de i2cdev_ioctl+0x247/0x2ed vfs_ioctl+0x21/0x30 sys_ioctl+0xb18/0xb41 Freed in i2cdev_ioctl_rdwr+0x1bb/0x1de age=68 cpu=0 pid=28 kfree+0x1bd/0x1cc i2cdev_ioctl_rdwr+0x1bb/0x1de i2cdev_ioctl+0x247/0x2ed vfs_ioctl+0x21/0x30 sys_ioctl+0xb18/0xb41 Fix this by calling virtio_get_buf() from the notify handler like other virtio drivers and by actually waiting for all the buffers to be completed.

In the Linux kernel, the following vulnerability has been resolved: rcu-tasks: Fix show_rcu_tasks_trace_gp_kthread buffer overflow There is a possibility of buffer overflow in show_rcu_tasks_trace_gp_kthread() if counters, passed to sprintf() are huge. Counter numbers, needed for this are unrealistically high, but buffer overflow is still possible. Use snprintf() with buffer size instead of sprintf(). Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix potential index out of bounds in color transformation function Fixes index out of bounds issue in the color transformation function. The issue could occur when the index 'i' exceeds the number of transfer function points (TRANSFER_FUNC_POINTS). The fix adds a check to ensure 'i' is within bounds before accessing the transfer function points. If 'i' is out of bounds, an error message is logged and the function returns false to indicate an error. Reported by smatch: drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:405 cm_helper_translate_curve_to_hw_format() error: buffer overflow 'output_tf->tf_pts.red' 1025 <= s32max drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:406 cm_helper_translate_curve_to_hw_format() error: buffer overflow 'output_tf->tf_pts.green' 1025 <= s32max drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:407 cm_helper_translate_curve_to_hw_format() error: buffer overflow 'output_tf->tf_pts.blue' 1025 <= s32max

In the Linux kernel, the following vulnerability has been resolved: IB/qib: Protect from buffer overflow in struct qib_user_sdma_pkt fields Overflowing either addrlimit or bytes_togo can allow userspace to trigger a buffer overflow of kernel memory. Check for overflows in all the places doing math on user controlled buffers.

In the Linux kernel, the following vulnerability has been resolved: powerpc/kasan: Fix early region not updated correctly The shadow's page table is not updated when PTE_RPN_SHIFT is 24 and PAGE_SHIFT is 12. It not only causes false positives but also false negative as shown the following text. Fix it by bringing the logic of kasan_early_shadow_page_entry here. 1. False Positive: ================================================================== BUG: KASAN: vmalloc-out-of-bounds in pcpu_alloc+0x508/0xa50 Write of size 16 at addr f57f3be0 by task swapper/0/1 CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.15.0-12267-gdebe436e77c7 #1 Call Trace: [c80d1c20] [c07fe7b8] dump_stack_lvl+0x4c/0x6c (unreliable) [c80d1c40] [c02ff668] print_address_description.constprop.0+0x88/0x300 [c80d1c70] [c02ff45c] kasan_report+0x1ec/0x200 [c80d1cb0] [c0300b20] kasan_check_range+0x160/0x2f0 [c80d1cc0] [c03018a4] memset+0x34/0x90 [c80d1ce0] [c0280108] pcpu_alloc+0x508/0xa50 [c80d1d40] [c02fd7bc] __kmem_cache_create+0xfc/0x570 [c80d1d70] [c0283d64] kmem_cache_create_usercopy+0x274/0x3e0 [c80d1db0] [c2036580] init_sd+0xc4/0x1d0 [c80d1de0] [c00044a0] do_one_initcall+0xc0/0x33c [c80d1eb0] [c2001624] kernel_init_freeable+0x2c8/0x384 [c80d1ef0] [c0004b14] kernel_init+0x24/0x170 [c80d1f10] [c001b26c] ret_from_kernel_thread+0x5c/0x64 Memory state around the buggy address: f57f3a80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f57f3b00: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 >f57f3b80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ^ f57f3c00: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f57f3c80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ================================================================== 2. False Negative (with KASAN tests): ================================================================== Before fix: ok 45 - kmalloc_double_kzfree # vmalloc_oob: EXPECTATION FAILED at lib/test_kasan.c:1039 KASAN failure expected in "((volatile char *)area)[3100]", but none occurred not ok 46 - vmalloc_oob not ok 1 - kasan ================================================================== After fix: ok 1 - kasan

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_scpi: Fix string overflow in SCPI genpd driver Without the bound checks for scpi_pd->name, it could result in the buffer overflow when copying the SCPI device name from the corresponding device tree node as the name string is set at maximum size of 30. Let us fix it by using devm_kasprintf so that the string buffer is allocated dynamically.

In the Linux kernel, the following vulnerability has been resolved: r8169: Fix possible ring buffer corruption on fragmented Tx packets. An issue was found on the RTL8125b when transmitting small fragmented packets, whereby invalid entries were inserted into the transmit ring buffer, subsequently leading to calls to dma_unmap_single() with a null address. This was caused by rtl8169_start_xmit() not noticing changes to nr_frags which may occur when small packets are padded (to work around hardware quirks) in rtl8169_tso_csum_v2(). To fix this, postpone inspecting nr_frags until after any padding has been applied.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Add a timeout to acquire the command queue semaphore Prevent forced completion handling on an entry that has not yet been assigned an index, causing an out of bounds access on idx = -22. Instead of waiting indefinitely for the sem, blocking flow now waits for index to be allocated or a sem acquisition timeout before beginning the timer for FW completion. Kernel log example: mlx5_core 0000:06:00.0: wait_func_handle_exec_timeout:1128:(pid 185911): cmd[-22]: CREATE_UCTX(0xa04) No done completion

In the Linux kernel, the following vulnerability has been resolved: HID: betop: fix slab-out-of-bounds Write in betop_probe Syzbot reported slab-out-of-bounds Write bug in hid-betopff driver. The problem is the driver assumes the device must have an input report but some malicious devices violate this assumption. So this patch checks hid_device's input is non empty before it's been used.

In the Linux kernel, the following vulnerability has been resolved: ocfs2: mount fails with buffer overflow in strlen Starting with kernel 5.11 built with CONFIG_FORTIFY_SOURCE mouting an ocfs2 filesystem with either o2cb or pcmk cluster stack fails with the trace below. Problem seems to be that strings for cluster stack and cluster name are not guaranteed to be null terminated in the disk representation, while strlcpy assumes that the source string is always null terminated. This causes a read outside of the source string triggering the buffer overflow detection. detected buffer overflow in strlen ------------[ cut here ]------------ kernel BUG at lib/string.c:1149! invalid opcode: 0000 [#1] SMP PTI CPU: 1 PID: 910 Comm: mount.ocfs2 Not tainted 5.14.0-1-amd64 #1 Debian 5.14.6-2 RIP: 0010:fortify_panic+0xf/0x11 ... Call Trace: ocfs2_initialize_super.isra.0.cold+0xc/0x18 [ocfs2] ocfs2_fill_super+0x359/0x19b0 [ocfs2] mount_bdev+0x185/0x1b0 legacy_get_tree+0x27/0x40 vfs_get_tree+0x25/0xb0 path_mount+0x454/0xa20 __x64_sys_mount+0x103/0x140 do_syscall_64+0x3b/0xc0 entry_SYSCALL_64_after_hwframe+0x44/0xae

A flaw was found in unrestricted eBPF usage by the BPF_BTF_LOAD, leading to a possible out-of-bounds memory write in the Linux kernel’s BPF subsystem due to the way a user loads BTF. This flaw allows a local user to crash or escalate their privileges on the system.

The regset (aka register set) feature in the Linux kernel before 3.2.10 does not properly handle the absence of .get and .set methods, which allows local users to cause a denial of service (NULL pointer dereference) or possibly have unspecified other impact via a (1) PTRACE_GETREGSET or (2) PTRACE_SETREGSET ptrace call.

In the Linux kernel, the following vulnerability has been resolved: drivers/perf: hisi_pcie: Fix out-of-bound access when valid event group The perf tool allows users to create event groups through following cmd [1], but the driver does not check whether the array index is out of bounds when writing data to the event_group array. If the number of events in an event_group is greater than HISI_PCIE_MAX_COUNTERS, the memory write overflow of event_group array occurs. Add array index check to fix the possible array out of bounds violation, and return directly when write new events are written to array bounds. There are 9 different events in an event_group. [1] perf stat -e '{pmu/event1/, ... ,pmu/event9/}'

In the Linux kernel, the following vulnerability has been resolved: comedi: vmk80xx: fix bulk-buffer overflow The driver is using endpoint-sized buffers but must not assume that the tx and rx buffers are of equal size or a malicious device could overflow the slab-allocated receive buffer when doing bulk transfers.

In the Linux kernel, the following vulnerability has been resolved: KVM: nVMX: Always make an attempt to map eVMCS after migration When enlightened VMCS is in use and nested state is migrated with vmx_get_nested_state()/vmx_set_nested_state() KVM can't map evmcs page right away: evmcs gpa is not 'struct kvm_vmx_nested_state_hdr' and we can't read it from VP assist page because userspace may decide to restore HV_X64_MSR_VP_ASSIST_PAGE after restoring nested state (and QEMU, for example, does exactly that). To make sure eVMCS is mapped /vmx_set_nested_state() raises KVM_REQ_GET_NESTED_STATE_PAGES request. Commit f2c7ef3ba955 ("KVM: nSVM: cancel KVM_REQ_GET_NESTED_STATE_PAGES on nested vmexit") added KVM_REQ_GET_NESTED_STATE_PAGES clearing to nested_vmx_vmexit() to make sure MSR permission bitmap is not switched when an immediate exit from L2 to L1 happens right after migration (caused by a pending event, for example). Unfortunately, in the exact same situation we still need to have eVMCS mapped so nested_sync_vmcs12_to_shadow() reflects changes in VMCS12 to eVMCS. As a band-aid, restore nested_get_evmcs_page() when clearing KVM_REQ_GET_NESTED_STATE_PAGES in nested_vmx_vmexit(). The 'fix' is far from being ideal as we can't easily propagate possible failures and even if we could, this is most likely already too late to do so. The whole 'KVM_REQ_GET_NESTED_STATE_PAGES' idea for mapping eVMCS after migration seems to be fragile as we diverge too much from the 'native' path when vmptr loading happens on vmx_set_nested_state().

In the Linux kernel, the following vulnerability has been resolved: cfg80211: call cfg80211_stop_ap when switch from P2P_GO type If the userspace tools switch from NL80211_IFTYPE_P2P_GO to NL80211_IFTYPE_ADHOC via send_msg(NL80211_CMD_SET_INTERFACE), it does not call the cleanup cfg80211_stop_ap(), this leads to the initialization of in-use data. For example, this path re-init the sdata->assigned_chanctx_list while it is still an element of assigned_vifs list, and makes that linked list corrupt.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix off by one in hdmi_14_process_transaction() The hdcp_i2c_offsets[] array did not have an entry for HDCP_MESSAGE_ID_WRITE_CONTENT_STREAM_TYPE so it led to an off by one read overflow. I added an entry and copied the 0x0 value for the offset from similar code in drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c. I also declared several of these arrays as having HDCP_MESSAGE_ID_MAX entries. This doesn't change the code, but it's just a belt and suspenders approach to try future proof the code.

In the Linux kernel, the following vulnerability has been resolved: media: staging/intel-ipu3: Fix set_fmt error handling If there in an error during a set_fmt, do not overwrite the previous sizes with the invalid config. Without this patch, v4l2-compliance ends up allocating 4GiB of RAM and causing the following OOPs [ 38.662975] ipu3-imgu 0000:00:05.0: swiotlb buffer is full (sz: 4096 bytes) [ 38.662980] DMA: Out of SW-IOMMU space for 4096 bytes at device 0000:00:05.0 [ 38.663010] general protection fault: 0000 [#1] PREEMPT SMP

In the Linux kernel, the following vulnerability has been resolved: io_uring: fix overflows checks in provide buffers Colin reported before possible overflow and sign extension problems in io_provide_buffers_prep(). As Linus pointed out previous attempt did nothing useful, see d81269fecb8ce ("io_uring: fix provide_buffers sign extension"). Do that with help of check_<op>_overflow helpers. And fix struct io_provide_buf::len type, as it doesn't make much sense to keep it signed.

In the Linux kernel, the following vulnerability has been resolved: tee: optee: Fix incorrect page free bug Pointer to the allocated pages (struct page *page) has already progressed towards the end of allocation. It is incorrect to perform __free_pages(page, order) using this pointer as we would free any arbitrary pages. Fix this by stop modifying the page pointer.

In the Linux kernel, the following vulnerability has been resolved: rtw88: Fix array overrun in rtw_get_tx_power_params() Using a kernel with the Undefined Behaviour Sanity Checker (UBSAN) enabled, the following array overrun is logged: ================================================================================ UBSAN: array-index-out-of-bounds in /home/finger/wireless-drivers-next/drivers/net/wireless/realtek/rtw88/phy.c:1789:34 index 5 is out of range for type 'u8 [5]' CPU: 2 PID: 84 Comm: kworker/u16:3 Tainted: G O 5.12.0-rc5-00086-gd88bba47038e-dirty #651 Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.50 09/29/2014 Workqueue: phy0 ieee80211_scan_work [mac80211] Call Trace: dump_stack+0x64/0x7c ubsan_epilogue+0x5/0x40 __ubsan_handle_out_of_bounds.cold+0x43/0x48 rtw_get_tx_power_params+0x83a/drivers/net/wireless/realtek/rtw88/0xad0 [rtw_core] ? rtw_pci_read16+0x20/0x20 [rtw_pci] ? check_hw_ready+0x50/0x90 [rtw_core] rtw_phy_get_tx_power_index+0x4d/0xd0 [rtw_core] rtw_phy_set_tx_power_level+0xee/0x1b0 [rtw_core] rtw_set_channel+0xab/0x110 [rtw_core] rtw_ops_config+0x87/0xc0 [rtw_core] ieee80211_hw_config+0x9d/0x130 [mac80211] ieee80211_scan_state_set_channel+0x81/0x170 [mac80211] ieee80211_scan_work+0x19f/0x2a0 [mac80211] process_one_work+0x1dd/0x3a0 worker_thread+0x49/0x330 ? rescuer_thread+0x3a0/0x3a0 kthread+0x134/0x150 ? kthread_create_worker_on_cpu+0x70/0x70 ret_from_fork+0x22/0x30 ================================================================================ The statement where an array is being overrun is shown in the following snippet: if (rate <= DESC_RATE11M) tx_power = pwr_idx_2g->cck_base[group]; else ====> tx_power = pwr_idx_2g->bw40_base[group]; The associated arrays are defined in main.h as follows: struct rtw_2g_txpwr_idx { u8 cck_base[6]; u8 bw40_base[5]; struct rtw_2g_1s_pwr_idx_diff ht_1s_diff; struct rtw_2g_ns_pwr_idx_diff ht_2s_diff; struct rtw_2g_ns_pwr_idx_diff ht_3s_diff; struct rtw_2g_ns_pwr_idx_diff ht_4s_diff; }; The problem arises because the value of group is 5 for channel 14. The trivial increase in the dimension of bw40_base fails as this struct must match the layout of efuse. The fix is to add the rate as an argument to rtw_get_channel_group() and set the group for channel 14 to 4 if rate <= DESC_RATE11M. This patch fixes commit fa6dfe6bff24 ("rtw88: resolve order of tx power setting routines")

In the Linux kernel, the following vulnerability has been resolved: dm rq: fix double free of blk_mq_tag_set in dev remove after table load fails When loading a device-mapper table for a request-based mapped device, and the allocation/initialization of the blk_mq_tag_set for the device fails, a following device remove will cause a double free. E.g. (dmesg): device-mapper: core: Cannot initialize queue for request-based dm-mq mapped device device-mapper: ioctl: unable to set up device queue for new table. Unable to handle kernel pointer dereference in virtual kernel address space Failing address: 0305e098835de000 TEID: 0305e098835de803 Fault in home space mode while using kernel ASCE. AS:000000025efe0007 R3:0000000000000024 Oops: 0038 ilc:3 [#1] SMP Modules linked in: ... lots of modules ... Supported: Yes, External CPU: 0 PID: 7348 Comm: multipathd Kdump: loaded Tainted: G W X 5.3.18-53-default #1 SLE15-SP3 Hardware name: IBM 8561 T01 7I2 (LPAR) Krnl PSW : 0704e00180000000 000000025e368eca (kfree+0x42/0x330) R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3 Krnl GPRS: 000000000000004a 000000025efe5230 c1773200d779968d 0000000000000000 000000025e520270 000000025e8d1b40 0000000000000003 00000007aae10000 000000025e5202a2 0000000000000001 c1773200d779968d 0305e098835de640 00000007a8170000 000003ff80138650 000000025e5202a2 000003e00396faa8 Krnl Code: 000000025e368eb8: c4180041e100 lgrl %r1,25eba50b8 000000025e368ebe: ecba06b93a55 risbg %r11,%r10,6,185,58 #000000025e368ec4: e3b010000008 ag %r11,0(%r1) >000000025e368eca: e310b0080004 lg %r1,8(%r11) 000000025e368ed0: a7110001 tmll %r1,1 000000025e368ed4: a7740129 brc 7,25e369126 000000025e368ed8: e320b0080004 lg %r2,8(%r11) 000000025e368ede: b904001b lgr %r1,%r11 Call Trace: [<000000025e368eca>] kfree+0x42/0x330 [<000000025e5202a2>] blk_mq_free_tag_set+0x72/0xb8 [<000003ff801316a8>] dm_mq_cleanup_mapped_device+0x38/0x50 [dm_mod] [<000003ff80120082>] free_dev+0x52/0xd0 [dm_mod] [<000003ff801233f0>] __dm_destroy+0x150/0x1d0 [dm_mod] [<000003ff8012bb9a>] dev_remove+0x162/0x1c0 [dm_mod] [<000003ff8012a988>] ctl_ioctl+0x198/0x478 [dm_mod] [<000003ff8012ac8a>] dm_ctl_ioctl+0x22/0x38 [dm_mod] [<000000025e3b11ee>] ksys_ioctl+0xbe/0xe0 [<000000025e3b127a>] __s390x_sys_ioctl+0x2a/0x40 [<000000025e8c15ac>] system_call+0xd8/0x2c8 Last Breaking-Event-Address: [<000000025e52029c>] blk_mq_free_tag_set+0x6c/0xb8 Kernel panic - not syncing: Fatal exception: panic_on_oops When allocation/initialization of the blk_mq_tag_set fails in dm_mq_init_request_queue(), it is uninitialized/freed, but the pointer is not reset to NULL; so when dev_remove() later gets into dm_mq_cleanup_mapped_device() it sees the pointer and tries to uninitialize and free it again. Fix this by setting the pointer to NULL in dm_mq_init_request_queue() error-handling. Also set it to NULL in dm_mq_cleanup_mapped_device().

In the Linux kernel, the following vulnerability has been resolved: sched: sch_cake: fix bulk flow accounting logic for host fairness In sch_cake, we keep track of the count of active bulk flows per host, when running in dst/src host fairness mode, which is used as the round-robin weight when iterating through flows. The count of active bulk flows is updated whenever a flow changes state. This has a peculiar interaction with the hash collision handling: when a hash collision occurs (after the set-associative hashing), the state of the hash bucket is simply updated to match the new packet that collided, and if host fairness is enabled, that also means assigning new per-host state to the flow. For this reason, the bulk flow counters of the host(s) assigned to the flow are decremented, before new state is assigned (and the counters, which may not belong to the same host anymore, are incremented again). Back when this code was introduced, the host fairness mode was always enabled, so the decrement was unconditional. When the configuration flags were introduced the *increment* was made conditional, but the *decrement* was not. Which of course can lead to a spurious decrement (and associated wrap-around to U16_MAX). AFAICT, when host fairness is disabled, the decrement and wrap-around happens as soon as a hash collision occurs (which is not that common in itself, due to the set-associative hashing). However, in most cases this is harmless, as the value is only used when host fairness mode is enabled. So in order to trigger an array overflow, sch_cake has to first be configured with host fairness disabled, and while running in this mode, a hash collision has to occur to cause the overflow. Then, the qdisc has to be reconfigured to enable host fairness, which leads to the array out-of-bounds because the wrapped-around value is retained and used as an array index. It seems that syzbot managed to trigger this, which is quite impressive in its own right. This patch fixes the issue by introducing the same conditional check on decrement as is used on increment. The original bug predates the upstreaming of cake, but the commit listed in the Fixes tag touched that code, meaning that this patch won't apply before that.

In the Linux kernel, the following vulnerability has been resolved: usb: typec: tcpm: cancel vdm and state machine hrtimer when unregister tcpm port A pending hrtimer may expire after the kthread_worker of tcpm port is destroyed, see below kernel dump when do module unload, fix it by cancel the 2 hrtimers. [ 111.517018] Unable to handle kernel paging request at virtual address ffff8000118cb880 [ 111.518786] blk_update_request: I/O error, dev sda, sector 60061185 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 111.526594] Mem abort info: [ 111.526597] ESR = 0x96000047 [ 111.526600] EC = 0x25: DABT (current EL), IL = 32 bits [ 111.526604] SET = 0, FnV = 0 [ 111.526607] EA = 0, S1PTW = 0 [ 111.526610] Data abort info: [ 111.526612] ISV = 0, ISS = 0x00000047 [ 111.526615] CM = 0, WnR = 1 [ 111.526619] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000041d75000 [ 111.526623] [ffff8000118cb880] pgd=10000001bffff003, p4d=10000001bffff003, pud=10000001bfffe003, pmd=10000001bfffa003, pte=0000000000000000 [ 111.526642] Internal error: Oops: 96000047 [#1] PREEMPT SMP [ 111.526647] Modules linked in: dwc3_imx8mp dwc3 phy_fsl_imx8mq_usb [last unloaded: tcpci] [ 111.526663] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.13.0-rc4-00927-gebbe9dbd802c-dirty #36 [ 111.526670] Hardware name: NXP i.MX8MPlus EVK board (DT) [ 111.526674] pstate: 800000c5 (Nzcv daIF -PAN -UAO -TCO BTYPE=--) [ 111.526681] pc : queued_spin_lock_slowpath+0x1a0/0x390 [ 111.526695] lr : _raw_spin_lock_irqsave+0x88/0xb4 [ 111.526703] sp : ffff800010003e20 [ 111.526706] x29: ffff800010003e20 x28: ffff00017f380180 [ 111.537156] buffer_io_error: 6 callbacks suppressed [ 111.537162] Buffer I/O error on dev sda1, logical block 60040704, async page read [ 111.539932] x27: ffff00017f3801c0 [ 111.539938] x26: ffff800010ba2490 x25: 0000000000000000 x24: 0000000000000001 [ 111.543025] blk_update_request: I/O error, dev sda, sector 60061186 op 0x0:(READ) flags 0x0 phys_seg 7 prio class 0 [ 111.548304] [ 111.548306] x23: 00000000000000c0 x22: ffff0000c2a9f184 x21: ffff00017f380180 [ 111.551374] Buffer I/O error on dev sda1, logical block 60040705, async page read [ 111.554499] [ 111.554503] x20: ffff0000c5f14210 x19: 00000000000000c0 x18: 0000000000000000 [ 111.557391] Buffer I/O error on dev sda1, logical block 60040706, async page read [ 111.561218] [ 111.561222] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 [ 111.564205] Buffer I/O error on dev sda1, logical block 60040707, async page read [ 111.570887] x14: 00000000000000f5 x13: 0000000000000001 x12: 0000000000000040 [ 111.570902] x11: ffff0000c05ac6d8 [ 111.583420] Buffer I/O error on dev sda1, logical block 60040708, async page read [ 111.588978] x10: 0000000000000000 x9 : 0000000000040000 [ 111.588988] x8 : 0000000000000000 [ 111.597173] Buffer I/O error on dev sda1, logical block 60040709, async page read [ 111.605766] x7 : ffff00017f384880 x6 : ffff8000118cb880 [ 111.605777] x5 : ffff00017f384880 [ 111.611094] Buffer I/O error on dev sda1, logical block 60040710, async page read [ 111.617086] x4 : 0000000000000000 x3 : ffff0000c2a9f184 [ 111.617096] x2 : ffff8000118cb880 [ 111.622242] Buffer I/O error on dev sda1, logical block 60040711, async page read [ 111.626927] x1 : ffff8000118cb880 x0 : ffff00017f384888 [ 111.626938] Call trace: [ 111.626942] queued_spin_lock_slowpath+0x1a0/0x390 [ 111.795809] kthread_queue_work+0x30/0xc0 [ 111.799828] state_machine_timer_handler+0x20/0x30 [ 111.804624] __hrtimer_run_queues+0x140/0x1e0 [ 111.808990] hrtimer_interrupt+0xec/0x2c0 [ 111.813004] arch_timer_handler_phys+0x38/0x50 [ 111.817456] handle_percpu_devid_irq+0x88/0x150 [ 111.821991] __handle_domain_irq+0x80/0xe0 [ 111.826093] gic_handle_irq+0xc0/0x140 [ 111.829848] el1_irq+0xbc/0x154 [ 111.832991] arch_cpu_idle+0x1c/0x2c [ 111.836572] default_idle_call+0x24/0x6c [ 111.840497] do_idle+0x238/0x2ac [ 1 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: md/raid1: properly indicate failure when ending a failed write request This patch addresses a data corruption bug in raid1 arrays using bitmaps. Without this fix, the bitmap bits for the failed I/O end up being cleared. Since we are in the failure leg of raid1_end_write_request, the request either needs to be retried (R1BIO_WriteError) or failed (R1BIO_Degraded).

In the Linux kernel, the following vulnerability has been resolved: net/sched: act_ct: fix wild memory access when clearing fragments while testing re-assembly/re-fragmentation using act_ct, it's possible to observe a crash like the following one: KASAN: maybe wild-memory-access in range [0x0001000000000448-0x000100000000044f] CPU: 50 PID: 0 Comm: swapper/50 Tainted: G S 5.12.0-rc7+ #424 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.4.3 01/17/2017 RIP: 0010:inet_frag_rbtree_purge+0x50/0xc0 Code: 00 fc ff df 48 89 c3 31 ed 48 89 df e8 a9 7a 38 ff 4c 89 fe 48 89 df 49 89 c6 e8 5b 3a 38 ff 48 8d 7b 40 48 89 f8 48 c1 e8 03 <42> 80 3c 20 00 75 59 48 8d bb d0 00 00 00 4c 8b 6b 40 48 89 f8 48 RSP: 0018:ffff888c31449db8 EFLAGS: 00010203 RAX: 0000200000000089 RBX: 000100000000040e RCX: ffffffff989eb960 RDX: 0000000000000140 RSI: ffffffff97cfb977 RDI: 000100000000044e RBP: 0000000000000900 R08: 0000000000000000 R09: ffffed1186289350 R10: 0000000000000003 R11: ffffed1186289350 R12: dffffc0000000000 R13: 000100000000040e R14: 0000000000000000 R15: ffff888155e02160 FS: 0000000000000000(0000) GS:ffff888c31440000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005600cb70a5b8 CR3: 0000000a2c014005 CR4: 00000000003706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <IRQ> inet_frag_destroy+0xa9/0x150 call_timer_fn+0x2d/0x180 run_timer_softirq+0x4fe/0xe70 __do_softirq+0x197/0x5a0 irq_exit_rcu+0x1de/0x200 sysvec_apic_timer_interrupt+0x6b/0x80 </IRQ> when act_ct temporarily stores an IP fragment, restoring the skb qdisc cb results in putting random data in FRAG_CB(), and this causes those "wild" memory accesses later, when the rbtree is purged. Never overwrite the skb cb in case tcf_ct_handle_fragments() returns -EINPROGRESS.

In the Linux kernel, the following vulnerability has been resolved: octeontx2-pf: fix a buffer overflow in otx2_set_rxfh_context() This function is called from ethtool_set_rxfh() and "*rss_context" comes from the user. Add some bounds checking to prevent memory corruption.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (w83791d) Fix NULL pointer dereference by removing unnecessary structure field If driver read val value sufficient for (val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7)) from device then Null pointer dereference occurs. (It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers) Also lm75[] does not serve a purpose anymore after switching to devm_i2c_new_dummy_device() in w83791d_detect_subclients(). The patch fixes possible NULL pointer dereference by removing lm75[]. Found by Linux Driver Verification project (linuxtesting.org). [groeck: Dropped unnecessary continuation lines, fixed multi-line alignment]

In the Linux kernel, the following vulnerability has been resolved: iommu/mediatek: Always enable the clk on resume In mtk_iommu_runtime_resume always enable the clk, even if m4u_dom is null. Otherwise the 'suspend' cb might disable the clk which is already disabled causing the warning: [ 1.586104] infra_m4u already disabled [ 1.586133] WARNING: CPU: 0 PID: 121 at drivers/clk/clk.c:952 clk_core_disable+0xb0/0xb8 [ 1.594391] mtk-iommu 10205000.iommu: bound 18001000.larb (ops mtk_smi_larb_component_ops) [ 1.598108] Modules linked in: [ 1.598114] CPU: 0 PID: 121 Comm: kworker/0:2 Not tainted 5.12.0-rc5 #69 [ 1.609246] mtk-iommu 10205000.iommu: bound 14027000.larb (ops mtk_smi_larb_component_ops) [ 1.617487] Hardware name: Google Elm (DT) [ 1.617491] Workqueue: pm pm_runtime_work [ 1.620545] mtk-iommu 10205000.iommu: bound 19001000.larb (ops mtk_smi_larb_component_ops) [ 1.627229] pstate: 60000085 (nZCv daIf -PAN -UAO -TCO BTYPE=--) [ 1.659297] pc : clk_core_disable+0xb0/0xb8 [ 1.663475] lr : clk_core_disable+0xb0/0xb8 [ 1.667652] sp : ffff800011b9bbe0 [ 1.670959] x29: ffff800011b9bbe0 x28: 0000000000000000 [ 1.676267] x27: ffff800011448000 x26: ffff8000100cfd98 [ 1.681574] x25: ffff800011b9bd48 x24: 0000000000000000 [ 1.686882] x23: 0000000000000000 x22: ffff8000106fad90 [ 1.692189] x21: 000000000000000a x20: ffff0000c0048500 [ 1.697496] x19: ffff0000c0048500 x18: ffffffffffffffff [ 1.702804] x17: 0000000000000000 x16: 0000000000000000 [ 1.708112] x15: ffff800011460300 x14: fffffffffffe0000 [ 1.713420] x13: ffff8000114602d8 x12: 0720072007200720 [ 1.718727] x11: 0720072007200720 x10: 0720072007200720 [ 1.724035] x9 : ffff800011b9bbe0 x8 : ffff800011b9bbe0 [ 1.729342] x7 : 0000000000000009 x6 : ffff8000114b8328 [ 1.734649] x5 : 0000000000000000 x4 : 0000000000000000 [ 1.739956] x3 : 00000000ffffffff x2 : ffff800011460298 [ 1.745263] x1 : 1af1d7de276f4500 x0 : 0000000000000000 [ 1.750572] Call trace: [ 1.753010] clk_core_disable+0xb0/0xb8 [ 1.756840] clk_core_disable_lock+0x24/0x40 [ 1.761105] clk_disable+0x20/0x30 [ 1.764501] mtk_iommu_runtime_suspend+0x88/0xa8 [ 1.769114] pm_generic_runtime_suspend+0x2c/0x48 [ 1.773815] __rpm_callback+0xe0/0x178 [ 1.777559] rpm_callback+0x24/0x88 [ 1.781041] rpm_suspend+0xdc/0x470 [ 1.784523] rpm_idle+0x12c/0x170 [ 1.787831] pm_runtime_work+0xa8/0xc0 [ 1.791573] process_one_work+0x1e8/0x360 [ 1.795580] worker_thread+0x44/0x478 [ 1.799237] kthread+0x150/0x158 [ 1.802460] ret_from_fork+0x10/0x30 [ 1.806034] ---[ end trace 82402920ef64573b ]--- [ 1.810728] ------------[ cut here ]------------ In addition, we now don't need to enable the clock from the function mtk_iommu_hw_init since it is already enabled by the resume.

In the Linux kernel, the following vulnerability has been resolved: mt76: mt7921: fix possible AOOB issue in mt7921_mcu_tx_rate_report Fix possible array out of bound access in mt7921_mcu_tx_rate_report. Remove unnecessary varibable in mt7921_mcu_tx_rate_report

In the Linux kernel, the following vulnerability has been resolved: mt76: mt7915: fix txrate reporting Properly check rate_info to fix unexpected reporting. [ 1215.161863] Call trace: [ 1215.164307] cfg80211_calculate_bitrate+0x124/0x200 [cfg80211] [ 1215.170139] ieee80211s_update_metric+0x80/0xc0 [mac80211] [ 1215.175624] ieee80211_tx_status_ext+0x508/0x838 [mac80211] [ 1215.181190] mt7915_mcu_get_rx_rate+0x28c/0x8d0 [mt7915e] [ 1215.186580] mt7915_mac_tx_free+0x324/0x7c0 [mt7915e] [ 1215.191623] mt7915_queue_rx_skb+0xa8/0xd0 [mt7915e] [ 1215.196582] mt76_dma_cleanup+0x7b0/0x11d0 [mt76] [ 1215.201276] __napi_poll+0x38/0xf8 [ 1215.204668] napi_workfn+0x40/0x80 [ 1215.208062] process_one_work+0x1fc/0x390 [ 1215.212062] worker_thread+0x48/0x4d0 [ 1215.215715] kthread+0x120/0x128 [ 1215.218935] ret_from_fork+0x10/0x1c

In the Linux kernel, the following vulnerability has been resolved: net: Only allow init netns to set default tcp cong to a restricted algo tcp_set_default_congestion_control() is netns-safe in that it writes to &net->ipv4.tcp_congestion_control, but it also sets ca->flags |= TCP_CONG_NON_RESTRICTED which is not namespaced. This has the unintended side-effect of changing the global net.ipv4.tcp_allowed_congestion_control sysctl, despite the fact that it is read-only: 97684f0970f6 ("net: Make tcp_allowed_congestion_control readonly in non-init netns") Resolve this netns "leak" by only allowing the init netns to set the default algorithm to one that is restricted. This restriction could be removed if tcp_allowed_congestion_control were namespace-ified in the future. This bug was uncovered with https://github.com/JonathonReinhart/linux-netns-sysctl-verify

In the Linux kernel, the following vulnerability has been resolved: NFSv4: Fix an Oops in pnfs_mark_request_commit() when doing O_DIRECT Fix an Oopsable condition in pnfs_mark_request_commit() when we're putting a set of writes on the commit list to reschedule them after a failed pNFS attempt.

In the Linux kernel, the following vulnerability has been resolved: tun: avoid double free in tun_free_netdev Avoid double free in tun_free_netdev() by moving the dev->tstats and tun->security allocs to a new ndo_init routine (tun_net_init()) that will be called by register_netdevice(). ndo_init is paired with the desctructor (tun_free_netdev()), so if there's an error in register_netdevice() the destructor will handle the frees. BUG: KASAN: double-free or invalid-free in selinux_tun_dev_free_security+0x1a/0x20 security/selinux/hooks.c:5605 CPU: 0 PID: 25750 Comm: syz-executor416 Not tainted 5.16.0-rc2-syzk #1 Hardware name: Red Hat KVM, BIOS Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x89/0xb5 lib/dump_stack.c:106 print_address_description.constprop.9+0x28/0x160 mm/kasan/report.c:247 kasan_report_invalid_free+0x55/0x80 mm/kasan/report.c:372 ____kasan_slab_free mm/kasan/common.c:346 [inline] __kasan_slab_free+0x107/0x120 mm/kasan/common.c:374 kasan_slab_free include/linux/kasan.h:235 [inline] slab_free_hook mm/slub.c:1723 [inline] slab_free_freelist_hook mm/slub.c:1749 [inline] slab_free mm/slub.c:3513 [inline] kfree+0xac/0x2d0 mm/slub.c:4561 selinux_tun_dev_free_security+0x1a/0x20 security/selinux/hooks.c:5605 security_tun_dev_free_security+0x4f/0x90 security/security.c:2342 tun_free_netdev+0xe6/0x150 drivers/net/tun.c:2215 netdev_run_todo+0x4df/0x840 net/core/dev.c:10627 rtnl_unlock+0x13/0x20 net/core/rtnetlink.c:112 __tun_chr_ioctl+0x80c/0x2870 drivers/net/tun.c:3302 tun_chr_ioctl+0x2f/0x40 drivers/net/tun.c:3311 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:874 [inline] __se_sys_ioctl fs/ioctl.c:860 [inline] __x64_sys_ioctl+0x19d/0x220 fs/ioctl.c:860 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3a/0x80 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae

In the Linux kernel, the following vulnerability has been resolved: hwmon: (lm90) Prevent integer overflow/underflow in hysteresis calculations Commit b50aa49638c7 ("hwmon: (lm90) Prevent integer underflows of temperature calculations") addressed a number of underflow situations when writing temperature limits. However, it missed one situation, seen when an attempt is made to set the hysteresis value to MAX_LONG and the critical temperature limit is negative. Use clamp_val() when setting the hysteresis temperature to ensure that the provided value can never overflow or underflow.