An issue was discovered in the Linux kernel through 5.11.8. The sound/soc/qcom/sdm845.c soundwire device driver has a buffer overflow when an unexpected port ID number is encountered, aka CID-1c668e1c0a0f. (This has been fixed in 5.12-rc4.)

In the Linux kernel, the following vulnerability has been resolved: iio: light: Add check for array bounds in veml6075_read_int_time_ms The array contains only 5 elements, but the index calculated by veml6075_read_int_time_index can range from 0 to 7, which could lead to out-of-bounds access. The check prevents this issue. Coverity Issue CID 1574309: (#1 of 1): Out-of-bounds read (OVERRUN) overrun-local: Overrunning array veml6075_it_ms of 5 4-byte elements at element index 7 (byte offset 31) using index int_index (which evaluates to 7) This is hardening against potentially broken hardware. Good to have but not necessary to backport.

BPF JIT compilers in the Linux kernel through 5.11.12 have incorrect computation of branch displacements, allowing them to execute arbitrary code within the kernel context. This affects arch/x86/net/bpf_jit_comp.c and arch/x86/net/bpf_jit_comp32.c.

In the Linux kernel, the following vulnerability has been resolved: io_uring: fix io_req_prep_async with provided buffers io_req_prep_async() can import provided buffers, commit the ring state by giving up on that before, it'll be reimported later if needed.

A heap out-of-bounds write vulnerability in the Linux Kernel ipvlan network driver can be exploited to achieve local privilege escalation. The out-of-bounds write is caused by missing skb->cb initialization in the ipvlan network driver. The vulnerability is reachable if CONFIG_IPVLAN is enabled. We recommend upgrading past commit 90cbed5247439a966b645b34eb0a2e037836ea8e.

An issue was discovered in the Linux kernel 4.18 through 5.10.16, as used by Xen. The backend allocation (aka be-alloc) mode of the drm_xen_front drivers was not meant to be a supported configuration, but this wasn't stated accordingly in its support status entry.

A flaw was found in the Linux kernel’s driver for the ASIX AX88179_178A-based USB 2.0/3.0 Gigabit Ethernet Devices. The vulnerability contains multiple out-of-bounds reads and possible out-of-bounds writes.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: increase scan_ies_len for S1G Currently the S1G capability element is not taken into account for the scan_ies_len, which leads to a buffer length validation failure in ieee80211_prep_hw_scan() and subsequent WARN in __ieee80211_start_scan(). This prevents hw scanning from functioning. To fix ensure we accommodate for the S1G capability length.

In the Linux kernel, the following vulnerability has been resolved: wifi: wilc1000: avoid buffer overflow in WID string configuration Fix the following copy overflow warning identified by Smatch checker. drivers/net/wireless/microchip/wilc1000/wlan_cfg.c:184 wilc_wlan_parse_response_frame() error: '__memcpy()' 'cfg->s[i]->str' copy overflow (512 vs 65537) This patch introduces size check before accessing the memory buffer. The checks are base on the WID type of received data from the firmware. For WID string configuration, the size limit is determined by individual element size in 'struct wilc_cfg_str_vals' that is maintained in 'len' field of 'struct wilc_cfg_str'.

In the Linux kernel, the following vulnerability has been resolved: ipv6: mcast: Delay put pmc->idev in mld_del_delrec() pmc->idev is still used in ip6_mc_clear_src(), so as mld_clear_delrec() does, the reference should be put after ip6_mc_clear_src() return.

An issue was discovered in the Linux kernel through 5.11.3. Certain iSCSI data structures do not have appropriate length constraints or checks, and can exceed the PAGE_SIZE value. An unprivileged user can send a Netlink message that is associated with iSCSI, and has a length up to the maximum length of a Netlink message.

In the Linux kernel, the following vulnerability has been resolved: libceph: fix invalid accesses to ceph_connection_v1_info There is a place where generic code in messenger.c is reading and another place where it is writing to con->v1 union member without checking that the union member is active (i.e. msgr1 is in use). On 64-bit systems, con->v1.auth_retry overlaps with con->v2.out_iter, so such a read is almost guaranteed to return a bogus value instead of 0 when msgr2 is in use. This ends up being fairly benign because the side effect is just the invalidation of the authorizer and successive fetching of new tickets. con->v1.connect_seq overlaps with con->v2.conn_bufs and the fact that it's being written to can cause more serious consequences, but luckily it's not something that happens often.

In the Linux kernel, the following vulnerability has been resolved: fbcon: fix integer overflow in fbcon_do_set_font Fix integer overflow vulnerabilities in fbcon_do_set_font() where font size calculations could overflow when handling user-controlled font parameters. The vulnerabilities occur when: 1. CALC_FONTSZ(h, pitch, charcount) performs h * pith * charcount multiplication with user-controlled values that can overflow. 2. FONT_EXTRA_WORDS * sizeof(int) + size addition can also overflow 3. This results in smaller allocations than expected, leading to buffer overflows during font data copying. Add explicit overflow checking using check_mul_overflow() and check_add_overflow() kernel helpers to safety validate all size calculations before allocation.

In the Linux kernel, the following vulnerability has been resolved: i40e: fix IRQ freeing in i40e_vsi_request_irq_msix error path If request_irq() in i40e_vsi_request_irq_msix() fails in an iteration later than the first, the error path wants to free the IRQs requested so far. However, it uses the wrong dev_id argument for free_irq(), so it does not free the IRQs correctly and instead triggers the warning: Trying to free already-free IRQ 173 WARNING: CPU: 25 PID: 1091 at kernel/irq/manage.c:1829 __free_irq+0x192/0x2c0 Modules linked in: i40e(+) [...] CPU: 25 UID: 0 PID: 1091 Comm: NetworkManager Not tainted 6.17.0-rc1+ #1 PREEMPT(lazy) Hardware name: [...] RIP: 0010:__free_irq+0x192/0x2c0 [...] Call Trace: <TASK> free_irq+0x32/0x70 i40e_vsi_request_irq_msix.cold+0x63/0x8b [i40e] i40e_vsi_request_irq+0x79/0x80 [i40e] i40e_vsi_open+0x21f/0x2f0 [i40e] i40e_open+0x63/0x130 [i40e] __dev_open+0xfc/0x210 __dev_change_flags+0x1fc/0x240 netif_change_flags+0x27/0x70 do_setlink.isra.0+0x341/0xc70 rtnl_newlink+0x468/0x860 rtnetlink_rcv_msg+0x375/0x450 netlink_rcv_skb+0x5c/0x110 netlink_unicast+0x288/0x3c0 netlink_sendmsg+0x20d/0x430 ____sys_sendmsg+0x3a2/0x3d0 ___sys_sendmsg+0x99/0xe0 __sys_sendmsg+0x8a/0xf0 do_syscall_64+0x82/0x2c0 entry_SYSCALL_64_after_hwframe+0x76/0x7e [...] </TASK> ---[ end trace 0000000000000000 ]--- Use the same dev_id for free_irq() as for request_irq(). I tested this with inserting code to fail intentionally.

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix untrusted unsigned subtract Fix the following Smatch static checker warning: net/rxrpc/rxgk_app.c:65 rxgk_yfs_decode_ticket() warn: untrusted unsigned subtract. 'ticket_len - 10 * 4' by prechecking the length of what we're trying to extract in two places in the token and decoding for a response packet. Also use sizeof() on the struct we're extracting rather specifying the size numerically to be consistent with the other related statements.

In the Linux kernel, the following vulnerability has been resolved: io_uring/memmap: cast nr_pages to size_t before shifting If the allocated size exceeds UINT_MAX, then it's necessary to cast the mr->nr_pages value to size_t to prevent it from overflowing. In practice this isn't much of a concern as the required memory size will have been validated upfront, and accounted to the user. And > 4GB sizes will be necessary to make the lack of a cast a problem, which greatly exceeds normal user locked_vm settings that are generally in the kb to mb range. However, if root is used, then accounting isn't done, and then it's possible to hit this issue.

In the Linux kernel, the following vulnerability has been resolved: staging: media: atomisp: Fix stack buffer overflow in gmin_get_var_int() When gmin_get_config_var() calls efi.get_variable() and the EFI variable is larger than the expected buffer size, two behaviors combine to create a stack buffer overflow: 1. gmin_get_config_var() does not return the proper error code when efi.get_variable() fails. It returns the stale 'ret' value from earlier operations instead of indicating the EFI failure. 2. When efi.get_variable() returns EFI_BUFFER_TOO_SMALL, it updates *out_len to the required buffer size but writes no data to the output buffer. However, due to bug #1, gmin_get_var_int() believes the call succeeded. The caller gmin_get_var_int() then performs: - Allocates val[CFG_VAR_NAME_MAX + 1] (65 bytes) on stack - Calls gmin_get_config_var(dev, is_gmin, var, val, &len) with len=64 - If EFI variable is >64 bytes, efi.get_variable() sets len=required_size - Due to bug #1, thinks call succeeded with len=required_size - Executes val[len] = 0, writing past end of 65-byte stack buffer This creates a stack buffer overflow when EFI variables are larger than 64 bytes. Since EFI variables can be controlled by firmware or system configuration, this could potentially be exploited for code execution. Fix the bug by returning proper error codes from gmin_get_config_var() based on EFI status instead of stale 'ret' value. The gmin_get_var_int() function is called during device initialization for camera sensor configuration on Intel Bay Trail and Cherry Trail platforms using the atomisp camera stack.

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: use array_index_nospec with indices that come from guest min and dest_id are guest-controlled indices. Using array_index_nospec() after the bounds checks clamps these values to mitigate speculative execution side-channels.

In the Linux kernel, the following vulnerability has been resolved: net: libwx: fix the using of Rx buffer DMA The wx_rx_buffer structure contained two DMA address fields: 'dma' and 'page_dma'. However, only 'page_dma' was actually initialized and used to program the Rx descriptor. But 'dma' was uninitialized and used in some paths. This could lead to undefined behavior, including DMA errors or use-after-free, if the uninitialized 'dma' was used. Althrough such error has not yet occurred, it is worth fixing in the code.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (corsair-cpro) Validate the size of the received input buffer Add buffer_recv_size to store the size of the received bytes. Validate buffer_recv_size in send_usb_cmd().

A NULL pointer dereference vulnerability was found in netlink_dump. This issue can occur when the Netlink socket receives the message(sendmsg) for the XFRM_MSG_GETSA, XFRM_MSG_GETPOLICY type message, and the DUMP flag is set and can cause a denial of service or possibly another unspecified impact. Due to the nature of the flaw, privilege escalation cannot be fully ruled out, although it is unlikely.

In the Linux kernel, the following vulnerability has been resolved: phy: tegra: xusb: Fix unbalanced regulator disable in UTMI PHY mode When transitioning from USB_ROLE_DEVICE to USB_ROLE_NONE, the code assumed that the regulator should be disabled. However, if the regulator is marked as always-on, regulator_is_enabled() continues to return true, leading to an incorrect attempt to disable a regulator which is not enabled. This can result in warnings such as: [ 250.155624] WARNING: CPU: 1 PID: 7326 at drivers/regulator/core.c:3004 _regulator_disable+0xe4/0x1a0 [ 250.155652] unbalanced disables for VIN_SYS_5V0 To fix this, we move the regulator control logic into tegra186_xusb_padctl_id_override() function since it's directly related to the ID override state. The regulator is now only disabled when the role transitions from USB_ROLE_HOST to USB_ROLE_NONE, by checking the VBUS_ID register. This ensures that regulator enable/disable operations are properly balanced and only occur when actually transitioning to/from host mode.

In the Linux kernel, the following vulnerability has been resolved: platform/x86: asus-wmi: Fix racy registrations asus_wmi_register_driver() may be called from multiple drivers concurrently, which can lead to the racy list operations, eventually corrupting the memory and hitting Oops on some ASUS machines. Also, the error handling is missing, and it forgot to unregister ACPI lps0 dev ops in the error case. This patch covers those issues by introducing a simple mutex at acpi_wmi_register_driver() & *_unregister_driver, and adding the proper call of asus_s2idle_check_unregister() in the error path.

In the Linux kernel, the following vulnerability has been resolved: xfs: do not propagate ENODATA disk errors into xattr code ENODATA (aka ENOATTR) has a very specific meaning in the xfs xattr code; namely, that the requested attribute name could not be found. However, a medium error from disk may also return ENODATA. At best, this medium error may escape to userspace as "attribute not found" when in fact it's an IO (disk) error. At worst, we may oops in xfs_attr_leaf_get() when we do: error = xfs_attr_leaf_hasname(args, &bp); if (error == -ENOATTR) { xfs_trans_brelse(args->trans, bp); return error; } because an ENODATA/ENOATTR error from disk leaves us with a null bp, and the xfs_trans_brelse will then null-deref it. As discussed on the list, we really need to modify the lower level IO functions to trap all disk errors and ensure that we don't let unique errors like this leak up into higher xfs functions - many like this should be remapped to EIO. However, this patch directly addresses a reported bug in the xattr code, and should be safe to backport to stable kernels. A larger-scope patch to handle more unique errors at lower levels can follow later. (Note, prior to 07120f1abdff we did not oops, but we did return the wrong error code to userspace.)

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: exynos: Fix programming of HCI_UTRL_NEXUS_TYPE On Google gs101, the number of UTP transfer request slots (nutrs) is 32, and in this case the driver ends up programming the UTRL_NEXUS_TYPE incorrectly as 0. This is because the left hand side of the shift is 1, which is of type int, i.e. 31 bits wide. Shifting by more than that width results in undefined behaviour. Fix this by switching to the BIT() macro, which applies correct type casting as required. This ensures the correct value is written to UTRL_NEXUS_TYPE (0xffffffff on gs101), and it also fixes a UBSAN shift warning: UBSAN: shift-out-of-bounds in drivers/ufs/host/ufs-exynos.c:1113:21 shift exponent 32 is too large for 32-bit type 'int' For consistency, apply the same change to the nutmrs / UTMRL_NEXUS_TYPE write.

In the Linux kernel, the following vulnerability has been resolved: HID: core: do not bypass hid_hw_raw_request hid_hw_raw_request() is actually useful to ensure the provided buffer and length are valid. Directly calling in the low level transport driver function bypassed those checks and allowed invalid paramto be used.

In the Linux kernel, the following vulnerability has been resolved: jfs: truncate good inode pages when hard link is 0 The fileset value of the inode copy from the disk by the reproducer is AGGR_RESERVED_I. When executing evict, its hard link number is 0, so its inode pages are not truncated. This causes the bugon to be triggered when executing clear_inode() because nrpages is greater than 0.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Add sanity check for file name The length of the file name should be smaller than the directory entry size.

In the Linux kernel, the following vulnerability has been resolved: i2c: core: Fix double-free of fwnode in i2c_unregister_device() Before commit df6d7277e552 ("i2c: core: Do not dereference fwnode in struct device"), i2c_unregister_device() only called fwnode_handle_put() on of_node-s in the form of calling of_node_put(client->dev.of_node). But after this commit the i2c_client's fwnode now unconditionally gets fwnode_handle_put() on it. When the i2c_client has no primary (ACPI / OF) fwnode but it does have a software fwnode, the software-node will be the primary node and fwnode_handle_put() will put() it. But for the software fwnode device_remove_software_node() will also put() it leading to a double free: [ 82.665598] ------------[ cut here ]------------ [ 82.665609] refcount_t: underflow; use-after-free. [ 82.665808] WARNING: CPU: 3 PID: 1502 at lib/refcount.c:28 refcount_warn_saturate+0xba/0x11 ... [ 82.666830] RIP: 0010:refcount_warn_saturate+0xba/0x110 ... [ 82.666962] <TASK> [ 82.666971] i2c_unregister_device+0x60/0x90 Fix this by not calling fwnode_handle_put() when the primary fwnode is a software-node.

In the Linux kernel, the following vulnerability has been resolved: net/sched: Make cake_enqueue return NET_XMIT_CN when past buffer_limit The following setup can trigger a WARNING in htb_activate due to the condition: !cl->leaf.q->q.qlen tc qdisc del dev lo root tc qdisc add dev lo root handle 1: htb default 1 tc class add dev lo parent 1: classid 1:1 \ htb rate 64bit tc qdisc add dev lo parent 1:1 handle f: \ cake memlimit 1b ping -I lo -f -c1 -s64 -W0.001 127.0.0.1 This is because the low memlimit leads to a low buffer_limit, which causes packet dropping. However, cake_enqueue still returns NET_XMIT_SUCCESS, causing htb_enqueue to call htb_activate with an empty child qdisc. We should return NET_XMIT_CN when packets are dropped from the same tin and flow. I do not believe return value of NET_XMIT_CN is necessary for packet drops in the case of ack filtering, as that is meant to optimize performance, not to signal congestion.

In the Linux kernel, the following vulnerability has been resolved: iommu/amd: Avoid stack buffer overflow from kernel cmdline While the kernel command line is considered trusted in most environments, avoid writing 1 byte past the end of "acpiid" if the "str" argument is maximum length.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix KMSAN uninit-value in extent_info usage KMSAN reported a use of uninitialized value in `__is_extent_mergeable()` and `__is_back_mergeable()` via the read extent tree path. The root cause is that `get_read_extent_info()` only initializes three fields (`fofs`, `blk`, `len`) of `struct extent_info`, leaving the remaining fields uninitialized. This leads to undefined behavior when those fields are accessed later, especially during extent merging. Fix it by zero-initializing the `extent_info` struct before population.

In the Linux kernel, the following vulnerability has been resolved: btrfs: do not allow relocation of partially dropped subvolumes [BUG] There is an internal report that balance triggered transaction abort, with the following call trace: item 85 key (594509824 169 0) itemoff 12599 itemsize 33 extent refs 1 gen 197740 flags 2 ref#0: tree block backref root 7 item 86 key (594558976 169 0) itemoff 12566 itemsize 33 extent refs 1 gen 197522 flags 2 ref#0: tree block backref root 7 ... BTRFS error (device loop0): extent item not found for insert, bytenr 594526208 num_bytes 16384 parent 449921024 root_objectid 934 owner 1 offset 0 BTRFS error (device loop0): failed to run delayed ref for logical 594526208 num_bytes 16384 type 182 action 1 ref_mod 1: -117 ------------[ cut here ]------------ BTRFS: Transaction aborted (error -117) WARNING: CPU: 1 PID: 6963 at ../fs/btrfs/extent-tree.c:2168 btrfs_run_delayed_refs+0xfa/0x110 [btrfs] And btrfs check doesn't report anything wrong related to the extent tree. [CAUSE] The cause is a little complex, firstly the extent tree indeed doesn't have the backref for 594526208. The extent tree only have the following two backrefs around that bytenr on-disk: item 65 key (594509824 METADATA_ITEM 0) itemoff 13880 itemsize 33 refs 1 gen 197740 flags TREE_BLOCK tree block skinny level 0 (176 0x7) tree block backref root CSUM_TREE item 66 key (594558976 METADATA_ITEM 0) itemoff 13847 itemsize 33 refs 1 gen 197522 flags TREE_BLOCK tree block skinny level 0 (176 0x7) tree block backref root CSUM_TREE But the such missing backref item is not an corruption on disk, as the offending delayed ref belongs to subvolume 934, and that subvolume is being dropped: item 0 key (934 ROOT_ITEM 198229) itemoff 15844 itemsize 439 generation 198229 root_dirid 256 bytenr 10741039104 byte_limit 0 bytes_used 345571328 last_snapshot 198229 flags 0x1000000000001(RDONLY) refs 0 drop_progress key (206324 EXTENT_DATA 2711650304) drop_level 2 level 2 generation_v2 198229 And that offending tree block 594526208 is inside the dropped range of that subvolume. That explains why there is no backref item for that bytenr and why btrfs check is not reporting anything wrong. But this also shows another problem, as btrfs will do all the orphan subvolume cleanup at a read-write mount. So half-dropped subvolume should not exist after an RW mount, and balance itself is also exclusive to subvolume cleanup, meaning we shouldn't hit a subvolume half-dropped during relocation. The root cause is, there is no orphan item for this subvolume. In fact there are 5 subvolumes from around 2021 that have the same problem. It looks like the original report has some older kernels running, and caused those zombie subvolumes. Thankfully upstream commit 8d488a8c7ba2 ("btrfs: fix subvolume/snapshot deletion not triggered on mount") has long fixed the bug. [ENHANCEMENT] For repairing such old fs, btrfs-progs will be enhanced. Considering how delayed the problem will show up (at run delayed ref time) and at that time we have to abort transaction already, it is too late. Instead here we reject any half-dropped subvolume for reloc tree at the earliest time, preventing confusion and extra time wasted on debugging similar bugs.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sync: fix double free in 'hci_discovery_filter_clear()' Function 'hci_discovery_filter_clear()' frees 'uuids' array and then sets it to NULL. There is a tiny chance of the following race: 'hci_cmd_sync_work()' 'update_passive_scan_sync()' 'hci_update_passive_scan_sync()' 'hci_discovery_filter_clear()' kfree(uuids); <-------------------------preempted--------------------------------> 'start_service_discovery()' 'hci_discovery_filter_clear()' kfree(uuids); // DOUBLE FREE <-------------------------preempted--------------------------------> uuids = NULL; To fix it let's add locking around 'kfree()' call and NULL pointer assignment. Otherwise the following backtrace fires: [ ] ------------[ cut here ]------------ [ ] kernel BUG at mm/slub.c:547! [ ] Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP [ ] CPU: 3 UID: 0 PID: 246 Comm: bluetoothd Tainted: G O 6.12.19-kernel #1 [ ] Tainted: [O]=OOT_MODULE [ ] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ ] pc : __slab_free+0xf8/0x348 [ ] lr : __slab_free+0x48/0x348 ... [ ] Call trace: [ ] __slab_free+0xf8/0x348 [ ] kfree+0x164/0x27c [ ] start_service_discovery+0x1d0/0x2c0 [ ] hci_sock_sendmsg+0x518/0x924 [ ] __sock_sendmsg+0x54/0x60 [ ] sock_write_iter+0x98/0xf8 [ ] do_iter_readv_writev+0xe4/0x1c8 [ ] vfs_writev+0x128/0x2b0 [ ] do_writev+0xfc/0x118 [ ] __arm64_sys_writev+0x20/0x2c [ ] invoke_syscall+0x68/0xf0 [ ] el0_svc_common.constprop.0+0x40/0xe0 [ ] do_el0_svc+0x1c/0x28 [ ] el0_svc+0x30/0xd0 [ ] el0t_64_sync_handler+0x100/0x12c [ ] el0t_64_sync+0x194/0x198 [ ] Code: 8b0002e6 eb17031f 54fffbe1 d503201f (d4210000) [ ] ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: sme: cap SSID length in __cfg80211_connect_result() If the ssid->datalen is more than IEEE80211_MAX_SSID_LEN (32) it would lead to memory corruption so add some bounds checking.

An issue was discovered in the Linux kernel 3.11 through 5.10.16, as used by Xen. To service requests to the PV backend, the driver maps grant references provided by the frontend. In this process, errors may be encountered. In one case, an error encountered earlier might be discarded by later processing, resulting in the caller assuming successful mapping, and hence subsequent operations trying to access space that wasn't mapped. In another case, internal state would be insufficiently updated, preventing safe recovery from the error. This affects drivers/block/xen-blkback/blkback.c.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7915: fix list corruption after hardware restart Since stations are recreated from scratch, all lists that wcids are added to must be cleared before calling ieee80211_restart_hw. Set wcid->sta = 0 for each wcid entry in order to ensure that they are not added again before they are ready.

In the Linux kernel, the following vulnerability has been resolved: dmaengine: nbpfaxi: Fix memory corruption in probe() The nbpf->chan[] array is allocated earlier in the nbpf_probe() function and it has "num_channels" elements. These three loops iterate one element farther than they should and corrupt memory. The changes to the second loop are more involved. In this case, we're copying data from the irqbuf[] array into the nbpf->chan[] array. If the data in irqbuf[i] is the error IRQ then we skip it, so the iterators are not in sync. I added a check to ensure that we don't go beyond the end of the irqbuf[] array. I'm pretty sure this can't happen, but it seemed harmless to add a check. On the other hand, after the loop has ended there is a check to ensure that the "chan" iterator is where we expect it to be. In the original code we went one element beyond the end of the array so the iterator wasn't in the correct place and it would always return -EINVAL. However, now it will always be in the correct place. I deleted the check since we know the result.

In the Linux kernel, the following vulnerability has been resolved: io_uring/net: commit partial buffers on retry Ring provided buffers are potentially only valid within the single execution context in which they were acquired. io_uring deals with this and invalidates them on retry. But on the networking side, if MSG_WAITALL is set, or if the socket is of the streaming type and too little was processed, then it will hang on to the buffer rather than recycle or commit it. This is problematic for two reasons: 1) If someone unregisters the provided buffer ring before a later retry, then the req->buf_list will no longer be valid. 2) If multiple sockers are using the same buffer group, then multiple receives can consume the same memory. This can cause data corruption in the application, as either receive could land in the same userspace buffer. Fix this by disallowing partial retries from pinning a provided buffer across multiple executions, if ring provided buffers are used.

In the Linux kernel, the following vulnerability has been resolved: iommufd: Prevent ALIGN() overflow When allocating IOVA the candidate range gets aligned to the target alignment. If the range is close to ULONG_MAX then the ALIGN() can wrap resulting in a corrupted iova. Open code the ALIGN() using get_add_overflow() to prevent this. This simplifies the checks as we don't need to check for length earlier either. Consolidate the two copies of this code under a single helper. This bug would allow userspace to create a mapping that overlaps with some other mapping or a reserved range.

In the Linux kernel, the following vulnerability has been resolved: ACPI: pfr_update: Fix the driver update version check The security-version-number check should be used rather than the runtime version check for driver updates. Otherwise, the firmware update would fail when the update binary had a lower runtime version number than the current one. [ rjw: Changelog edits ]

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Remove WARN_ON_ONCE() call from ufshcd_uic_cmd_compl() The UIC completion interrupt may be disabled while an UIC command is being processed. When the UIC completion interrupt is reenabled, an UIC interrupt is triggered and the WARN_ON_ONCE(!cmd) statement is hit. Hence this patch that removes this kernel warning.

IBM Db2 for Linux, UNIX and Windows (includes Db2 Connect Server) 10.5, 11.1, and 11.5 db2set is vulnerable to a buffer overflow, caused by improper bounds checking. An attacker could overflow the buffer and execute arbitrary code. IBM X-Force ID: 252184.

In the Linux kernel, the following vulnerability has been resolved: dmaengine: fsl-edma: free irq correctly in remove path Add fsl_edma->txirq/errirq check to avoid below warning because no errirq at i.MX9 platform. Otherwise there will be kernel dump: WARNING: CPU: 0 PID: 11 at kernel/irq/devres.c:144 devm_free_irq+0x74/0x80 Modules linked in: CPU: 0 UID: 0 PID: 11 Comm: kworker/u8:0 Not tainted 6.12.0-rc7#18 Hardware name: NXP i.MX93 11X11 EVK board (DT) Workqueue: events_unbound deferred_probe_work_func pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : devm_free_irq+0x74/0x80 lr : devm_free_irq+0x48/0x80 Call trace: devm_free_irq+0x74/0x80 (P) devm_free_irq+0x48/0x80 (L) fsl_edma_remove+0xc4/0xc8 platform_remove+0x28/0x44 device_remove+0x4c/0x80

In the Linux kernel, the following vulnerability has been resolved: ASoC: codec: sma1307: Fix memory corruption in sma1307_setting_loaded() The sma1307->set.header_size is how many integers are in the header (there are 8 of them) but instead of allocating space of 8 integers we allocate 8 bytes. This leads to memory corruption when we copy data it on the next line: memcpy(sma1307->set.header, data, sma1307->set.header_size * sizeof(int)); Also since we're immediately copying over the memory in ->set.header, there is no need to zero it in the allocator. Use devm_kmalloc_array() to allocate the memory instead.

In the Linux kernel, the following vulnerability has been resolved: iio: backend: fix out-of-bound write The buffer is set to 80 character. If a caller write more characters, count is truncated to the max available space in "simple_write_to_buffer". But afterwards a string terminator is written to the buffer at offset count without boundary check. The zero termination is written OUT-OF-BOUND. Add a check that the given buffer is smaller then the buffer to prevent.

In the Linux kernel, the following vulnerability has been resolved: tcp: Clear tcp_sk(sk)->fastopen_rsk in tcp_disconnect(). syzbot reported the splat below where a socket had tcp_sk(sk)->fastopen_rsk in the TCP_ESTABLISHED state. [0] syzbot reused the server-side TCP Fast Open socket as a new client before the TFO socket completes 3WHS: 1. accept() 2. connect(AF_UNSPEC) 3. connect() to another destination As of accept(), sk->sk_state is TCP_SYN_RECV, and tcp_disconnect() changes it to TCP_CLOSE and makes connect() possible, which restarts timers. Since tcp_disconnect() forgot to clear tcp_sk(sk)->fastopen_rsk, the retransmit timer triggered the warning and the intended packet was not retransmitted. Let's call reqsk_fastopen_remove() in tcp_disconnect(). [0]: WARNING: CPU: 2 PID: 0 at net/ipv4/tcp_timer.c:542 tcp_retransmit_timer (net/ipv4/tcp_timer.c:542 (discriminator 7)) Modules linked in: CPU: 2 UID: 0 PID: 0 Comm: swapper/2 Not tainted 6.17.0-rc5-g201825fb4278 #62 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:tcp_retransmit_timer (net/ipv4/tcp_timer.c:542 (discriminator 7)) Code: 41 55 41 54 55 53 48 8b af b8 08 00 00 48 89 fb 48 85 ed 0f 84 55 01 00 00 0f b6 47 12 3c 03 74 0c 0f b6 47 12 3c 04 74 04 90 <0f> 0b 90 48 8b 85 c0 00 00 00 48 89 ef 48 8b 40 30 e8 6a 4f 06 3e RSP: 0018:ffffc900002f8d40 EFLAGS: 00010293 RAX: 0000000000000002 RBX: ffff888106911400 RCX: 0000000000000017 RDX: 0000000002517619 RSI: ffffffff83764080 RDI: ffff888106911400 RBP: ffff888106d5c000 R08: 0000000000000001 R09: ffffc900002f8de8 R10: 00000000000000c2 R11: ffffc900002f8ff8 R12: ffff888106911540 R13: ffff888106911480 R14: ffff888106911840 R15: ffffc900002f8de0 FS: 0000000000000000(0000) GS:ffff88907b768000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f8044d69d90 CR3: 0000000002c30003 CR4: 0000000000370ef0 Call Trace: <IRQ> tcp_write_timer (net/ipv4/tcp_timer.c:738) call_timer_fn (kernel/time/timer.c:1747) __run_timers (kernel/time/timer.c:1799 kernel/time/timer.c:2372) timer_expire_remote (kernel/time/timer.c:2385 kernel/time/timer.c:2376 kernel/time/timer.c:2135) tmigr_handle_remote_up (kernel/time/timer_migration.c:944 kernel/time/timer_migration.c:1035) __walk_groups.isra.0 (kernel/time/timer_migration.c:533 (discriminator 1)) tmigr_handle_remote (kernel/time/timer_migration.c:1096) handle_softirqs (./arch/x86/include/asm/jump_label.h:36 ./include/trace/events/irq.h:142 kernel/softirq.c:580) irq_exit_rcu (kernel/softirq.c:614 kernel/softirq.c:453 kernel/softirq.c:680 kernel/softirq.c:696) sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1050 (discriminator 35) arch/x86/kernel/apic/apic.c:1050 (discriminator 35)) </IRQ>

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix buffer free/clear order in deferred receive path Fix a use-after-free window by correcting the buffer release sequence in the deferred receive path. The code freed the RQ buffer first and only then cleared the context pointer under the lock. Concurrent paths (e.g., ABTS and the repost path) also inspect and release the same pointer under the lock, so the old order could lead to double-free/UAF. Note that the repost path already uses the correct pattern: detach the pointer under the lock, then free it after dropping the lock. The deferred path should do the same.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Validate UAC3 power domain descriptors, too UAC3 power domain descriptors need to be verified with its variable bLength for avoiding the unexpected OOB accesses by malicious firmware, too.

In the Linux kernel, the following vulnerability has been resolved: net: lapbether: ignore ops-locked netdevs Syzkaller managed to trigger lock dependency in xsk_notify via register_netdevice. As discussed in [0], using register_netdevice in the notifiers is problematic so skip adding lapbeth for ops-locked devices. xsk_notifier+0xa4/0x280 net/xdp/xsk.c:1645 notifier_call_chain+0xbc/0x410 kernel/notifier.c:85 call_netdevice_notifiers_info+0xbe/0x140 net/core/dev.c:2230 call_netdevice_notifiers_extack net/core/dev.c:2268 [inline] call_netdevice_notifiers net/core/dev.c:2282 [inline] unregister_netdevice_many_notify+0xf9d/0x2700 net/core/dev.c:12077 unregister_netdevice_many net/core/dev.c:12140 [inline] unregister_netdevice_queue+0x305/0x3f0 net/core/dev.c:11984 register_netdevice+0x18f1/0x2270 net/core/dev.c:11149 lapbeth_new_device drivers/net/wan/lapbether.c:420 [inline] lapbeth_device_event+0x5b1/0xbe0 drivers/net/wan/lapbether.c:462 notifier_call_chain+0xbc/0x410 kernel/notifier.c:85 call_netdevice_notifiers_info+0xbe/0x140 net/core/dev.c:2230 call_netdevice_notifiers_extack net/core/dev.c:2268 [inline] call_netdevice_notifiers net/core/dev.c:2282 [inline] __dev_notify_flags+0x12c/0x2e0 net/core/dev.c:9497 netif_change_flags+0x108/0x160 net/core/dev.c:9526 dev_change_flags+0xba/0x250 net/core/dev_api.c:68 devinet_ioctl+0x11d5/0x1f50 net/ipv4/devinet.c:1200 inet_ioctl+0x3a7/0x3f0 net/ipv4/af_inet.c:1001 0: https://lore.kernel.org/netdev/20250625140357.6203d0af@kernel.org/