In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sync: reject oversized Broadcast Announcement prepend Existing advertising instances can already hold the maximum extended advertising payload. When hci_adv_bcast_annoucement() prepends the Broadcast Announcement service data to that payload, the combined data may no longer fit in the temporary buffer used to rebuild the advertising data. Reject that case before copying the existing payload and report the failure through the device log. This keeps the existing advertising data intact and avoids overrunning the temporary buffer.

In the Linux kernel, the following vulnerability has been resolved: ocfs2: fix data corruption after failed write When buffered write fails to copy data into underlying page cache page, ocfs2_write_end_nolock() just zeroes out and dirties the page. This can leave dirty page beyond EOF and if page writeback tries to write this page before write succeeds and expands i_size, page gets into inconsistent state where page dirty bit is clear but buffer dirty bits stay set resulting in page data never getting written and so data copied to the page is lost. Fix the problem by invalidating page beyond EOF after failed write.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7915: fix list corruption after hardware restart Since stations are recreated from scratch, all lists that wcids are added to must be cleared before calling ieee80211_restart_hw. Set wcid->sta = 0 for each wcid entry in order to ensure that they are not added again before they are ready.

In the Linux kernel, the following vulnerability has been resolved: bnxt_en: Fix memory corruption when FW resources change during ifdown bnxt_set_dflt_rings() assumes that it is always called before any TC has been created. So it doesn't take bp->num_tc into account and assumes that it is always 0 or 1. In the FW resource or capability change scenario, the FW will return flags in bnxt_hwrm_if_change() that will cause the driver to reinitialize and call bnxt_cancel_reservations(). This will lead to bnxt_init_dflt_ring_mode() calling bnxt_set_dflt_rings() and bp->num_tc may be greater than 1. This will cause bp->tx_ring[] to be sized too small and cause memory corruption in bnxt_alloc_cp_rings(). Fix it by properly scaling the TX rings by bp->num_tc in the code paths mentioned above. Add 2 helper functions to determine bp->tx_nr_rings and bp->tx_nr_rings_per_tc.

In the Linux kernel, the following vulnerability has been resolved: perf: Avoid undefined behavior from stopping/starting inactive events Calling pmu->start()/stop() on perf events in PERF_EVENT_STATE_OFF can leave event->hw.idx at -1. When PMU drivers later attempt to use this negative index as a shift exponent in bitwise operations, it leads to UBSAN shift-out-of-bounds reports. The issue is a logical flaw in how event groups handle throttling when some members are intentionally disabled. Based on the analysis and the reproducer provided by Mark Rutland (this issue on both arm64 and x86-64). The scenario unfolds as follows: 1. A group leader event is configured with a very aggressive sampling period (e.g., sample_period = 1). This causes frequent interrupts and triggers the throttling mechanism. 2. A child event in the same group is created in a disabled state (.disabled = 1). This event remains in PERF_EVENT_STATE_OFF. Since it hasn't been scheduled onto the PMU, its event->hw.idx remains initialized at -1. 3. When throttling occurs, perf_event_throttle_group() and later perf_event_unthrottle_group() iterate through all siblings, including the disabled child event. 4. perf_event_throttle()/unthrottle() are called on this inactive child event, which then call event->pmu->start()/stop(). 5. The PMU driver receives the event with hw.idx == -1 and attempts to use it as a shift exponent. e.g., in macros like PMCNTENSET(idx), leading to the UBSAN report. The throttling mechanism attempts to start/stop events that are not actively scheduled on the hardware. Move the state check into perf_event_throttle()/perf_event_unthrottle() so that inactive events are skipped entirely. This ensures only active events with a valid hw.idx are processed, preventing undefined behavior and silencing UBSAN warnings. The corrected check ensures true before proceeding with PMU operations. The problem can be reproduced with the syzkaller reproducer:

In the Linux kernel, the following vulnerability has been resolved: iommu/s390: Fix memory corruption when using identity domain zpci_get_iommu_ctrs() returns counter information to be reported as part of device statistics; these counters are stored as part of the s390_domain. The problem, however, is that the identity domain is not backed by an s390_domain and so the conversion via to_s390_domain() yields a bad address that is zero'd initially and read on-demand later via a sysfs read. These counters aren't necessary for the identity domain; just return NULL in this case. This issue was discovered via KASAN with reports that look like: BUG: KASAN: global-out-of-bounds in zpci_fmb_enable_device when using the identity domain for a device on s390.

In the Linux kernel, the following vulnerability has been resolved: wifi: wilc1000: avoid buffer overflow in WID string configuration Fix the following copy overflow warning identified by Smatch checker. drivers/net/wireless/microchip/wilc1000/wlan_cfg.c:184 wilc_wlan_parse_response_frame() error: '__memcpy()' 'cfg->s[i]->str' copy overflow (512 vs 65537) This patch introduces size check before accessing the memory buffer. The checks are base on the WID type of received data from the firmware. For WID string configuration, the size limit is determined by individual element size in 'struct wilc_cfg_str_vals' that is maintained in 'len' field of 'struct wilc_cfg_str'.

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: sme: cap SSID length in __cfg80211_connect_result() If the ssid->datalen is more than IEEE80211_MAX_SSID_LEN (32) it would lead to memory corruption so add some bounds checking.

In the Linux kernel, the following vulnerability has been resolved: ASoC: codec: sma1307: Fix memory corruption in sma1307_setting_loaded() The sma1307->set.header_size is how many integers are in the header (there are 8 of them) but instead of allocating space of 8 integers we allocate 8 bytes. This leads to memory corruption when we copy data it on the next line: memcpy(sma1307->set.header, data, sma1307->set.header_size * sizeof(int)); Also since we're immediately copying over the memory in ->set.header, there is no need to zero it in the allocator. Use devm_kmalloc_array() to allocate the memory instead.

In the Linux kernel, the following vulnerability has been resolved: platform/x86: asus-wmi: Fix racy registrations asus_wmi_register_driver() may be called from multiple drivers concurrently, which can lead to the racy list operations, eventually corrupting the memory and hitting Oops on some ASUS machines. Also, the error handling is missing, and it forgot to unregister ACPI lps0 dev ops in the error case. This patch covers those issues by introducing a simple mutex at acpi_wmi_register_driver() & *_unregister_driver, and adding the proper call of asus_s2idle_check_unregister() in the error path.

In the Linux kernel, the following vulnerability has been resolved: drm/gem: Fix inconsistent plane dimension calculation in drm_gem_fb_init_with_funcs() drm_gem_fb_init_with_funcs() computes sub-sampled plane dimensions using plain integer division: unsigned int width = mode_cmd->width / (i ? info->hsub : 1); unsigned int height = mode_cmd->height / (i ? info->vsub : 1); However, the ioctl-level framebuffer_check() in drm_framebuffer.c uses drm_format_info_plane_width/height() which round up dimensions via DIV_ROUND_UP(). This inconsistency corrupts the subsequent GEM object size check for certain pixel format and dimension combinations. For example, with NV12 (vsub=2) and a 1-pixel-tall framebuffer the GEM size validation path sees height=0 instead of height=1. The expression (height - 1) then wraps to UINT_MAX as an unsigned int, causing min_size to overflow and wrap back to a small value. A tiny GEM object therefore passes the size guard, yet when the GPU accesses the chroma plane it will read or write memory beyond the object's bounds. Fix by replacing the open-coded divisions with drm_format_info_plane_width() and drm_format_info_plane_height(), which use DIV_ROUND_UP() and match the calculation already used in framebuffer_check().

In the Linux kernel, the following vulnerability has been resolved: HID: intel-thc-hid: intel-thc: Fix incorrect pointer arithmetic in I2C regs save Improper use of secondary pointer (&dev->i2c_subip_regs) caused kernel crash and out-of-bounds error: BUG: KASAN: slab-out-of-bounds in _regmap_bulk_read+0x449/0x510 Write of size 4 at addr ffff888136005dc0 by task kworker/u33:5/5107 CPU: 3 UID: 0 PID: 5107 Comm: kworker/u33:5 Not tainted 6.16.0+ #3 PREEMPT(voluntary) Workqueue: async async_run_entry_fn Call Trace: <TASK> dump_stack_lvl+0x76/0xa0 print_report+0xd1/0x660 ? __pfx__raw_spin_lock_irqsave+0x10/0x10 ? kasan_complete_mode_report_info+0x26/0x200 kasan_report+0xe1/0x120 ? _regmap_bulk_read+0x449/0x510 ? _regmap_bulk_read+0x449/0x510 __asan_report_store4_noabort+0x17/0x30 _regmap_bulk_read+0x449/0x510 ? __pfx__regmap_bulk_read+0x10/0x10 regmap_bulk_read+0x270/0x3d0 pio_complete+0x1ee/0x2c0 [intel_thc] ? __pfx_pio_complete+0x10/0x10 [intel_thc] ? __pfx_pio_wait+0x10/0x10 [intel_thc] ? regmap_update_bits_base+0x13b/0x1f0 thc_i2c_subip_pio_read+0x117/0x270 [intel_thc] thc_i2c_subip_regs_save+0xc2/0x140 [intel_thc] ? __pfx_thc_i2c_subip_regs_save+0x10/0x10 [intel_thc] [...] The buggy address belongs to the object at ffff888136005d00 which belongs to the cache kmalloc-rnd-12-192 of size 192 The buggy address is located 0 bytes to the right of allocated 192-byte region [ffff888136005d00, ffff888136005dc0) Replaced with direct array indexing (&dev->i2c_subip_regs[i]) to ensure safe memory access.

In the Linux kernel, the following vulnerability has been resolved: efi: stmm: Fix incorrect buffer allocation method The communication buffer allocated by setup_mm_hdr() is later on passed to tee_shm_register_kernel_buf(). The latter expects those buffers to be contiguous pages, but setup_mm_hdr() just uses kmalloc(). That can cause various corruptions or BUGs, specifically since commit 9aec2fb0fd5e ("slab: allocate frozen pages"), though it was broken before as well. Fix this by using alloc_pages_exact() instead of kmalloc().

In the Linux kernel, the following vulnerability has been resolved: udf: fix partition descriptor append bookkeeping Mounting a crafted UDF image with repeated partition descriptors can trigger a heap out-of-bounds write in part_descs_loc[]. handle_partition_descriptor() deduplicates entries by partition number, but appended slots never record partnum. As a result duplicate Partition Descriptors are appended repeatedly and num_part_descs keeps growing. Once the table is full, the growth path still sizes the allocation from partnum even though inserts are indexed by num_part_descs. If partnum is already aligned to PART_DESC_ALLOC_STEP, ALIGN(partnum, step) can keep the old capacity and the next append writes past the end of the table. Store partnum in the appended slot and size growth from the next append count so deduplication and capacity tracking follow the same model.

In the Linux kernel, the following vulnerability has been resolved: pstore/ram: fix buffer overflow in persistent_ram_save_old() persistent_ram_save_old() can be called multiple times for the same persistent_ram_zone (e.g., via ramoops_pstore_read -> ramoops_get_next_prz for PSTORE_TYPE_DMESG records). Currently, the function only allocates prz->old_log when it is NULL, but it unconditionally updates prz->old_log_size to the current buffer size and then performs memcpy_fromio() using this new size. If the buffer size has grown since the first allocation (which can happen across different kernel boot cycles), this leads to: 1. A heap buffer overflow (OOB write) in the memcpy_fromio() calls 2. A subsequent OOB read when ramoops_pstore_read() accesses the buffer using the incorrect (larger) old_log_size The KASAN splat would look similar to: BUG: KASAN: slab-out-of-bounds in ramoops_pstore_read+0x... Read of size N at addr ... by task ... The conditions are likely extremely hard to hit: 0. Crash with a ramoops write of less-than-record-max-size bytes. 1. Reboot: ramoops registers, pstore_get_records(0) reads old crash, allocates old_log with size X 2. Crash handler registered, timer started (if pstore_update_ms >= 0) 3. Oops happens (non-fatal, system continues) 4. pstore_dump() writes oops via ramoops_pstore_write() size Y (>X) 5. pstore_new_entry = 1, pstore_timer_kick() called 6. System continues running (not a panic oops) 7. Timer fires after pstore_update_ms milliseconds 8. pstore_timefunc() → schedule_work() → pstore_dowork() → pstore_get_records(1) 9. ramoops_get_next_prz() → persistent_ram_save_old() 10. buffer_size() returns Y, but old_log is X bytes 11. Y > X: memcpy_fromio() overflows heap Requirements: - a prior crash record exists that did not fill the record size (almost impossible since the crash handler writes as much as it can possibly fit into the record, capped by max record size and the kmsg buffer almost always exceeds the max record size) - pstore_update_ms >= 0 (disabled by default) - Non-fatal oops (system survives) Free and reallocate the buffer when the new size differs from the previously allocated size. This ensures old_log always has sufficient space for the data being copied.

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix untrusted unsigned subtract Fix the following Smatch static checker warning: net/rxrpc/rxgk_app.c:65 rxgk_yfs_decode_ticket() warn: untrusted unsigned subtract. 'ticket_len - 10 * 4' by prechecking the length of what we're trying to extract in two places in the token and decoding for a response packet. Also use sizeof() on the struct we're extracting rather specifying the size numerically to be consistent with the other related statements.

In the Linux kernel, the following vulnerability has been resolved: PCI: endpoint: Fix configfs group list head handling Doing a list_del() on the epf_group field of struct pci_epf_driver in pci_epf_remove_cfs() is not correct as this field is a list head, not a list entry. This list_del() call triggers a KASAN warning when an endpoint function driver which has a configfs attribute group is torn down: ================================================================== BUG: KASAN: slab-use-after-free in pci_epf_remove_cfs+0x17c/0x198 Write of size 8 at addr ffff00010f4a0d80 by task rmmod/319 CPU: 3 UID: 0 PID: 319 Comm: rmmod Not tainted 6.16.0-rc2 #1 NONE Hardware name: Radxa ROCK 5B (DT) Call trace: show_stack+0x2c/0x84 (C) dump_stack_lvl+0x70/0x98 print_report+0x17c/0x538 kasan_report+0xb8/0x190 __asan_report_store8_noabort+0x20/0x2c pci_epf_remove_cfs+0x17c/0x198 pci_epf_unregister_driver+0x18/0x30 nvmet_pci_epf_cleanup_module+0x24/0x30 [nvmet_pci_epf] __arm64_sys_delete_module+0x264/0x424 invoke_syscall+0x70/0x260 el0_svc_common.constprop.0+0xac/0x230 do_el0_svc+0x40/0x58 el0_svc+0x48/0xdc el0t_64_sync_handler+0x10c/0x138 el0t_64_sync+0x198/0x19c ... Remove this incorrect list_del() call from pci_epf_remove_cfs().

In the Linux kernel, the following vulnerability has been resolved: vsock: fix buffer size clamping order In vsock_update_buffer_size(), the buffer size was being clamped to the maximum first, and then to the minimum. If a user sets a minimum buffer size larger than the maximum, the minimum check overrides the maximum check, inverting the constraint. This breaks the intended socket memory boundaries by allowing the vsk->buffer_size to grow beyond the configured vsk->buffer_max_size. Fix this by checking the minimum first, and then the maximum. This ensures the buffer size never exceeds the buffer_max_size.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Validate UAC3 power domain descriptors, too UAC3 power domain descriptors need to be verified with its variable bLength for avoiding the unexpected OOB accesses by malicious firmware, too.

In the Linux kernel, the following vulnerability has been resolved: net/sched: mqprio: fix stack out-of-bounds write in tc entry parsing TCA_MQPRIO_TC_ENTRY_INDEX is validated using NLA_POLICY_MAX(NLA_U32, TC_QOPT_MAX_QUEUE), which allows the value TC_QOPT_MAX_QUEUE (16). This leads to a 4-byte out-of-bounds stack write in the fp[] array, which only has room for 16 elements (0–15). Fix this by changing the policy to allow only up to TC_QOPT_MAX_QUEUE - 1.

In the Linux kernel, the following vulnerability has been resolved: netfs: Fix unbuffered write error handling If all the subrequests in an unbuffered write stream fail, the subrequest collector doesn't update the stream->transferred value and it retains its initial LONG_MAX value. Unfortunately, if all active streams fail, then we take the smallest value of { LONG_MAX, LONG_MAX, ... } as the value to set in wreq->transferred - which is then returned from ->write_iter(). LONG_MAX was chosen as the initial value so that all the streams can be quickly assessed by taking the smallest value of all stream->transferred - but this only works if we've set any of them. Fix this by adding a flag to indicate whether the value in stream->transferred is valid and checking that when we integrate the values. stream->transferred can then be initialised to zero. This was found by running the generic/750 xfstest against cifs with cache=none. It splices data to the target file. Once (if) it has used up all the available scratch space, the writes start failing with ENOSPC. This causes ->write_iter() to fail. However, it was returning wreq->transferred, i.e. LONG_MAX, rather than an error (because it thought the amount transferred was non-zero) and iter_file_splice_write() would then try to clean up that amount of pipe bufferage - leading to an oops when it overran. The kernel log showed: CIFS: VFS: Send error in write = -28 followed by: BUG: kernel NULL pointer dereference, address: 0000000000000008 with: RIP: 0010:iter_file_splice_write+0x3a4/0x520 do_splice+0x197/0x4e0 or: RIP: 0010:pipe_buf_release (include/linux/pipe_fs_i.h:282) iter_file_splice_write (fs/splice.c:755) Also put a warning check into splice to announce if ->write_iter() returned that it had written more than it was asked to.

In the Linux kernel, the following vulnerability has been resolved: staging: media: atomisp: Fix stack buffer overflow in gmin_get_var_int() When gmin_get_config_var() calls efi.get_variable() and the EFI variable is larger than the expected buffer size, two behaviors combine to create a stack buffer overflow: 1. gmin_get_config_var() does not return the proper error code when efi.get_variable() fails. It returns the stale 'ret' value from earlier operations instead of indicating the EFI failure. 2. When efi.get_variable() returns EFI_BUFFER_TOO_SMALL, it updates *out_len to the required buffer size but writes no data to the output buffer. However, due to bug #1, gmin_get_var_int() believes the call succeeded. The caller gmin_get_var_int() then performs: - Allocates val[CFG_VAR_NAME_MAX + 1] (65 bytes) on stack - Calls gmin_get_config_var(dev, is_gmin, var, val, &len) with len=64 - If EFI variable is >64 bytes, efi.get_variable() sets len=required_size - Due to bug #1, thinks call succeeded with len=required_size - Executes val[len] = 0, writing past end of 65-byte stack buffer This creates a stack buffer overflow when EFI variables are larger than 64 bytes. Since EFI variables can be controlled by firmware or system configuration, this could potentially be exploited for code execution. Fix the bug by returning proper error codes from gmin_get_config_var() based on EFI status instead of stale 'ret' value. The gmin_get_var_int() function is called during device initialization for camera sensor configuration on Intel Bay Trail and Cherry Trail platforms using the atomisp camera stack.

In the Linux kernel, the following vulnerability has been resolved: HID: appletb-kbd: fix memory corruption of input_handler_list In appletb_kbd_probe an input handler is initialised and then registered with input core through input_register_handler(). When this happens input core will add the input handler (specifically its node) to the global input_handler_list. The input_handler_list is central to the functionality of input core and is traversed in various places in input core. An example of this is when a new input device is plugged in and gets registered with input core. The input_handler in probe is allocated as device managed memory. If a probe failure occurs after input_register_handler() the input_handler memory is freed, yet it will remain in the input_handler_list. This effectively means the input_handler_list contains a dangling pointer to data belonging to a freed input handler. This causes an issue when any other input device is plugged in - in my case I had an old PixArt HP USB optical mouse and I decided to plug it in after a failure occurred after input_register_handler(). This lead to the registration of this input device via input_register_device which involves traversing over every handler in the corrupted input_handler_list and calling input_attach_handler(), giving each handler a chance to bind to newly registered device. The core of this bug is a UAF which causes memory corruption of input_handler_list and to fix it we must ensure the input handler is unregistered from input core, this is done through input_unregister_handler(). [ 63.191597] ================================================================== [ 63.192094] BUG: KASAN: slab-use-after-free in input_attach_handler.isra.0+0x1a9/0x1e0 [ 63.192094] Read of size 8 at addr ffff888105ea7c80 by task kworker/0:2/54 [ 63.192094] [ 63.192094] CPU: 0 UID: 0 PID: 54 Comm: kworker/0:2 Not tainted 6.16.0-rc2-00321-g2aa6621d [ 63.192094] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.164 [ 63.192094] Workqueue: usb_hub_wq hub_event [ 63.192094] Call Trace: [ 63.192094] <TASK> [ 63.192094] dump_stack_lvl+0x53/0x70 [ 63.192094] print_report+0xce/0x670 [ 63.192094] kasan_report+0xce/0x100 [ 63.192094] input_attach_handler.isra.0+0x1a9/0x1e0 [ 63.192094] input_register_device+0x76c/0xd00 [ 63.192094] hidinput_connect+0x686d/0xad60 [ 63.192094] hid_connect+0xf20/0x1b10 [ 63.192094] hid_hw_start+0x83/0x100 [ 63.192094] hid_device_probe+0x2d1/0x680 [ 63.192094] really_probe+0x1c3/0x690 [ 63.192094] __driver_probe_device+0x247/0x300 [ 63.192094] driver_probe_device+0x49/0x210 [ 63.192094] __device_attach_driver+0x160/0x320 [ 63.192094] bus_for_each_drv+0x10f/0x190 [ 63.192094] __device_attach+0x18e/0x370 [ 63.192094] bus_probe_device+0x123/0x170 [ 63.192094] device_add+0xd4d/0x1460 [ 63.192094] hid_add_device+0x30b/0x910 [ 63.192094] usbhid_probe+0x920/0xe00 [ 63.192094] usb_probe_interface+0x363/0x9a0 [ 63.192094] really_probe+0x1c3/0x690 [ 63.192094] __driver_probe_device+0x247/0x300 [ 63.192094] driver_probe_device+0x49/0x210 [ 63.192094] __device_attach_driver+0x160/0x320 [ 63.192094] bus_for_each_drv+0x10f/0x190 [ 63.192094] __device_attach+0x18e/0x370 [ 63.192094] bus_probe_device+0x123/0x170 [ 63.192094] device_add+0xd4d/0x1460 [ 63.192094] usb_set_configuration+0xd14/0x1880 [ 63.192094] usb_generic_driver_probe+0x78/0xb0 [ 63.192094] usb_probe_device+0xaa/0x2e0 [ 63.192094] really_probe+0x1c3/0x690 [ 63.192094] __driver_probe_device+0x247/0x300 [ 63.192094] driver_probe_device+0x49/0x210 [ 63.192094] __device_attach_driver+0x160/0x320 [ 63.192094] bus_for_each_drv+0x10f/0x190 [ 63.192094] __device_attach+0x18e/0x370 [ 63.192094] bus_probe_device+0x123/0x170 [ 63.192094] device_add+0xd4d/0x1460 [ 63.192094] usb_new_device+0x7b4/0x1000 [ 63.192094] hub_event+0x234d/0x3 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: md/md-llbitmap: skip reading rdevs that are not in_sync When reading bitmap pages from member disks, the code iterates through all rdevs and attempts to read from the first available one. However, it only checks for raid_disk assignment and Faulty flag, missing the In_sync flag check. This can cause bitmap data to be read from spare disks that are still being rebuilt and don't have valid bitmap information yet. Reading stale or uninitialized bitmap data from such disks can lead to incorrect dirty bit tracking, potentially causing data corruption during recovery or normal operation. Add the In_sync flag check to ensure bitmap pages are only read from fully synchronized member disks that have valid bitmap data.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7921: fix a potential clc buffer length underflow The buf_len is used to limit the iterations for retrieving the country power setting and may underflow under certain conditions due to changes in the power table in CLC. This underflow leads to an almost infinite loop or an invalid power setting resulting in driver initialization failure.

In the Linux kernel, the following vulnerability has been resolved: RDMA/mana: Validate rx_hash_key_len Sashiko points out that rx_hash_key_len comes from a uAPI structure and is blindly passed to memcpy, allowing the userspace to trash kernel memory. Bounds check it so the memcpy cannot overflow.

In the Linux kernel, the following vulnerability has been resolved: crypto: nx - fix bounce buffer leaks in nx842_crypto_{alloc,free}_ctx The bounce buffers are allocated with __get_free_pages() using BOUNCE_BUFFER_ORDER (order 2 = 4 pages), but both the allocation error path and nx842_crypto_free_ctx() release the buffers with free_page(). Use free_pages() with the matching order instead.

In the Linux kernel, the following vulnerability has been resolved: iommu/amd: Avoid stack buffer overflow from kernel cmdline While the kernel command line is considered trusted in most environments, avoid writing 1 byte past the end of "acpiid" if the "str" argument is maximum length.

In the Linux kernel, the following vulnerability has been resolved: mtk-sd: Prevent memory corruption from DMA map failure If msdc_prepare_data() fails to map the DMA region, the request is not prepared for data receiving, but msdc_start_data() proceeds the DMA with previous setting. Since this will lead a memory corruption, we have to stop the request operation soon after the msdc_prepare_data() fails to prepare it.

In the Linux kernel, the following vulnerability has been resolved: iio: backend: fix out-of-bound write The buffer is set to 80 character. If a caller write more characters, count is truncated to the max available space in "simple_write_to_buffer". But afterwards a string terminator is written to the buffer at offset count without boundary check. The zero termination is written OUT-OF-BOUND. Add a check that the given buffer is smaller then the buffer to prevent.

In the Linux kernel, the following vulnerability has been resolved: dmaengine: nbpfaxi: Fix memory corruption in probe() The nbpf->chan[] array is allocated earlier in the nbpf_probe() function and it has "num_channels" elements. These three loops iterate one element farther than they should and corrupt memory. The changes to the second loop are more involved. In this case, we're copying data from the irqbuf[] array into the nbpf->chan[] array. If the data in irqbuf[i] is the error IRQ then we skip it, so the iterators are not in sync. I added a check to ensure that we don't go beyond the end of the irqbuf[] array. I'm pretty sure this can't happen, but it seemed harmless to add a check. On the other hand, after the loop has ended there is a check to ensure that the "chan" iterator is where we expect it to be. In the original code we went one element beyond the end of the array so the iterator wasn't in the correct place and it would always return -EINVAL. However, now it will always be in the correct place. I deleted the check since we know the result.

In the Linux kernel, the following vulnerability has been resolved: net: skbuff: preserve shared-frag marker during coalescing skb_try_coalesce() can attach paged frags from @from to @to. If @from has SKBFL_SHARED_FRAG set, the resulting @to skb can contain the same externally-owned or page-cache-backed frags, but the shared-frag marker is currently lost. That breaks the invariant relied on by later in-place writers. In particular, ESP input checks skb_has_shared_frag() before deciding whether an uncloned nonlinear skb can skip skb_cow_data(). If TCP receive coalescing has moved shared frags into an unmarked skb, ESP can see skb_has_shared_frag() as false and decrypt in place over page-cache backed frags. Propagate SKBFL_SHARED_FRAG when skb_try_coalesce() transfers paged frags. The tailroom copy path does not need the marker because it copies bytes into @to's linear data rather than transferring frag descriptors.

In the Linux kernel, the following vulnerability has been resolved: crypto: acomp - fix wrong pointer stored by acomp_save_req() acomp_save_req() stores &req->chain in req->base.data. When acomp_reqchain_done() is invoked on asynchronous completion, it receives &req->chain as the data argument but casts it directly to struct acomp_req. Since data points to the chain member, all subsequent field accesses are at a wrong offset, resulting in memory corruption. The issue occurs when an asynchronous hardware implementation, such as the QAT driver, completes a request that uses the DMA virtual address interface (e.g. acomp_request_set_src_dma()). This combination causes crypto_acomp_compress() to enter the acomp_do_req_chain() path, which sets acomp_reqchain_done() as the completion callback via acomp_save_req(). With KASAN enabled, this manifests as a general protection fault in acomp_reqchain_done(): general protection fault, probably for non-canonical address 0xe000040000000000 KASAN: probably user-memory-access in range [0x0000400000000000-0x0000400000000007] RIP: 0010:acomp_reqchain_done+0x15b/0x4e0 Call Trace: <IRQ> qat_comp_alg_callback+0x5d/0xa0 [intel_qat] adf_ring_response_handler+0x376/0x8b0 [intel_qat] adf_response_handler+0x60/0x170 [intel_qat] tasklet_action_common+0x223/0x820 handle_softirqs+0x1ab/0x640 </IRQ> Fix this by storing the request itself in req->base.data instead of &req->chain, so that acomp_reqchain_done() receives the correct pointer. Simplify acomp_restore_req() accordingly to access req->chain directly.

In the Linux kernel, the following vulnerability has been resolved: fbdev: Fix vmalloc out-of-bounds write in fast_imageblit This issue triggers when a userspace program does an ioctl FBIOPUT_CON2FBMAP by passing console number and frame buffer number. Ideally this maps console to frame buffer and updates the screen if console is visible. As part of mapping it has to do resize of console according to frame buffer info. if this resize fails and returns from vc_do_resize() and continues further. At this point console and new frame buffer are mapped and sets display vars. Despite failure still it continue to proceed updating the screen at later stages where vc_data is related to previous frame buffer and frame buffer info and display vars are mapped to new frame buffer and eventully leading to out-of-bounds write in fast_imageblit(). This bheviour is excepted only when fg_console is equal to requested console which is a visible console and updates screen with invalid struct references in fbcon_putcs().

In the Linux kernel, the following vulnerability has been resolved: fbdev: fix potential buffer overflow in do_register_framebuffer() The current implementation may lead to buffer overflow when: 1. Unregistration creates NULL gaps in registered_fb[] 2. All array slots become occupied despite num_registered_fb < FB_MAX 3. The registration loop exceeds array bounds Add boundary check to prevent registered_fb[FB_MAX] access.

In the Linux kernel, the following vulnerability has been resolved: drm/nouveau: fix u32 overflow in pushbuf reloc bounds check nouveau_gem_pushbuf_reloc_apply() validates each relocation with if (r->reloc_bo_offset + 4 > nvbo->bo.base.size) but reloc_bo_offset is __u32 (uapi/drm/nouveau_drm.h) and the integer literal 4 promotes to unsigned int, so the addition is performed in 32 bits and wraps before the comparison against the size_t bo size. Cast to u64 so the addition happens in 64-bit arithmetic. [ Add Fixes: tag. - Danilo ]

A heap-based buffer overflow in the vrend_renderer_transfer_write_iov function in vrend_renderer.c in virglrenderer through 0.8.0 allows guest OS users to cause a denial of service, or QEMU guest-to-host escape and code execution, via VIRGL_CCMD_RESOURCE_INLINE_WRITE commands.

In the Linux kernel, the following vulnerability has been resolved: ipmi:msghandler: Fix potential memory corruption in ipmi_create_user() The "intf" list iterator is an invalid pointer if the correct "intf->intf_num" is not found. Calling atomic_dec(&intf->nr_users) on and invalid pointer will lead to memory corruption. We don't really need to call atomic_dec() if we haven't called atomic_add_return() so update the if (intf->in_shutdown) path as well.

In the Linux kernel, the following vulnerability has been resolved: net: libwx: fix the using of Rx buffer DMA The wx_rx_buffer structure contained two DMA address fields: 'dma' and 'page_dma'. However, only 'page_dma' was actually initialized and used to program the Rx descriptor. But 'dma' was uninitialized and used in some paths. This could lead to undefined behavior, including DMA errors or use-after-free, if the uninitialized 'dma' was used. Althrough such error has not yet occurred, it is worth fixing in the code.

The iowarrior_write function in drivers/usb/misc/iowarrior.c in the Linux kernel before 2.6.37 does not properly allocate memory, which might allow local users to trigger a heap-based buffer overflow, and consequently cause a denial of service or gain privileges, via a long report.

In the Linux kernel, the following vulnerability has been resolved: io_uring/net: commit partial buffers on retry Ring provided buffers are potentially only valid within the single execution context in which they were acquired. io_uring deals with this and invalidates them on retry. But on the networking side, if MSG_WAITALL is set, or if the socket is of the streaming type and too little was processed, then it will hang on to the buffer rather than recycle or commit it. This is problematic for two reasons: 1) If someone unregisters the provided buffer ring before a later retry, then the req->buf_list will no longer be valid. 2) If multiple sockers are using the same buffer group, then multiple receives can consume the same memory. This can cause data corruption in the application, as either receive could land in the same userspace buffer. Fix this by disallowing partial retries from pinning a provided buffer across multiple executions, if ring provided buffers are used.

In the Linux kernel, the following vulnerability has been resolved: EDAC/skx_common: Fix general protection fault After loading i10nm_edac (which automatically loads skx_edac_common), if unload only i10nm_edac, then reload it and perform error injection testing, a general protection fault may occur: mce: [Hardware Error]: Machine check events logged Oops: general protection fault ... ... Workqueue: events mce_gen_pool_process RIP: 0010:string+0x53/0xe0 ... Call Trace: <TASK> ? die_addr+0x37/0x90 ? exc_general_protection+0x1e7/0x3f0 ? asm_exc_general_protection+0x26/0x30 ? string+0x53/0xe0 vsnprintf+0x23e/0x4c0 snprintf+0x4d/0x70 skx_adxl_decode+0x16a/0x330 [skx_edac_common] skx_mce_check_error.part.0+0xf8/0x220 [skx_edac_common] skx_mce_check_error+0x17/0x20 [skx_edac_common] ... The issue arose was because the variable 'adxl_component_count' (inside skx_edac_common), which counts the ADXL components, was not reset. During the reloading of i10nm_edac, the count was incremented by the actual number of ADXL components again, resulting in a count that was double the real number of ADXL components. This led to an out-of-bounds reference to the ADXL component array, causing the general protection fault above. Fix this issue by resetting the 'adxl_component_count' in adxl_put(), which is called during the unloading of {skx,i10nm}_edac.

In the Linux kernel, the following vulnerability has been resolved: Squashfs: check return result of sb_min_blocksize Syzkaller reports an "UBSAN: shift-out-of-bounds in squashfs_bio_read" bug. Syzkaller forks multiple processes which after mounting the Squashfs filesystem, issues an ioctl("/dev/loop0", LOOP_SET_BLOCK_SIZE, 0x8000). Now if this ioctl occurs at the same time another process is in the process of mounting a Squashfs filesystem on /dev/loop0, the failure occurs. When this happens the following code in squashfs_fill_super() fails. ---- msblk->devblksize = sb_min_blocksize(sb, SQUASHFS_DEVBLK_SIZE); msblk->devblksize_log2 = ffz(~msblk->devblksize); ---- sb_min_blocksize() returns 0, which means msblk->devblksize is set to 0. As a result, ffz(~msblk->devblksize) returns 64, and msblk->devblksize_log2 is set to 64. This subsequently causes the UBSAN: shift-out-of-bounds in fs/squashfs/block.c:195:36 shift exponent 64 is too large for 64-bit type 'u64' (aka 'unsigned long long') This commit adds a check for a 0 return by sb_min_blocksize().

In the Linux kernel, the following vulnerability has been resolved: wifi: p54: prevent buffer-overflow in p54_rx_eeprom_readback() Robert Morris reported: |If a malicious USB device pretends to be an Intersil p54 wifi |interface and generates an eeprom_readback message with a large |eeprom->v1.len, p54_rx_eeprom_readback() will copy data from the |message beyond the end of priv->eeprom. | |static void p54_rx_eeprom_readback(struct p54_common *priv, | struct sk_buff *skb) |{ | struct p54_hdr *hdr = (struct p54_hdr *) skb->data; | struct p54_eeprom_lm86 *eeprom = (struct p54_eeprom_lm86 *) hdr->data; | | if (priv->fw_var >= 0x509) { | memcpy(priv->eeprom, eeprom->v2.data, | le16_to_cpu(eeprom->v2.len)); | } else { | memcpy(priv->eeprom, eeprom->v1.data, | le16_to_cpu(eeprom->v1.len)); | } | [...] The eeprom->v{1,2}.len is set by the driver in p54_download_eeprom(). The device is supposed to provide the same length back to the driver. But yes, it's possible (like shown in the report) to alter the value to something that causes a crash/panic due to overrun. This patch addresses the issue by adding the size to the common device context, so p54_rx_eeprom_readback no longer relies on possibly tampered values... That said, it also checks if the "firmware" altered the value and no longer copies them. The one, small saving grace is: Before the driver tries to read the eeprom, it needs to upload >a< firmware. the vendor firmware has a proprietary license and as a reason, it is not present on most distributions by default.

In the Linux kernel, the following vulnerability has been resolved: ring-buffer: Do not trigger WARN_ON() due to a commit_overrun When reading a memory mapped buffer the reader page is just swapped out with the last page written in the write buffer. If the reader page is the same as the commit buffer (the buffer that is currently being written to) it was assumed that it should never have missed events. If it does, it triggers a WARN_ON_ONCE(). But there just happens to be one scenario where this can legitimately happen. That is on a commit_overrun. A commit overrun is when an interrupt preempts an event being written to the buffer and then the interrupt adds so many new events that it fills and wraps the buffer back to the commit. Any new events would then be dropped and be reported as "missed_events". In this case, the next page to read is the commit buffer and after the swap of the reader page, the reader page will be the commit buffer, but this time there will be missed events and this triggers the following warning: ------------[ cut here ]------------ WARNING: CPU: 2 PID: 1127 at kernel/trace/ring_buffer.c:7357 ring_buffer_map_get_reader+0x49a/0x780 Modules linked in: kvm_intel kvm irqbypass CPU: 2 UID: 0 PID: 1127 Comm: trace-cmd Not tainted 6.15.0-rc7-test-00004-g478bc2824b45-dirty #564 PREEMPT Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:ring_buffer_map_get_reader+0x49a/0x780 Code: 00 00 00 48 89 fe 48 c1 ee 03 80 3c 2e 00 0f 85 ec 01 00 00 4d 3b a6 a8 00 00 00 0f 85 8a fd ff ff 48 85 c0 0f 84 55 fe ff ff <0f> 0b e9 4e fe ff ff be 08 00 00 00 4c 89 54 24 58 48 89 54 24 50 RSP: 0018:ffff888121787dc0 EFLAGS: 00010002 RAX: 00000000000006a2 RBX: ffff888100062800 RCX: ffffffff8190cb49 RDX: ffff888126934c00 RSI: 1ffff11020200a15 RDI: ffff8881010050a8 RBP: dffffc0000000000 R08: 0000000000000000 R09: ffffed1024d26982 R10: ffff888126934c17 R11: ffff8881010050a8 R12: ffff888126934c00 R13: ffff8881010050b8 R14: ffff888101005000 R15: ffff888126930008 FS: 00007f95c8cd7540(0000) GS:ffff8882b576e000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f95c8de4dc0 CR3: 0000000128452002 CR4: 0000000000172ef0 Call Trace: <TASK> ? __pfx_ring_buffer_map_get_reader+0x10/0x10 tracing_buffers_ioctl+0x283/0x370 __x64_sys_ioctl+0x134/0x190 do_syscall_64+0x79/0x1c0 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f95c8de48db Code: 00 48 89 44 24 18 31 c0 48 8d 44 24 60 c7 04 24 10 00 00 00 48 89 44 24 08 48 8d 44 24 20 48 89 44 24 10 b8 10 00 00 00 0f 05 <89> c2 3d 00 f0 ff ff 77 1c 48 8b 44 24 18 64 48 2b 04 25 28 00 00 RSP: 002b:00007ffe037ba110 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007ffe037bb2b0 RCX: 00007f95c8de48db RDX: 0000000000000000 RSI: 0000000000005220 RDI: 0000000000000006 RBP: 00007ffe037ba180 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007ffe037bb6f8 R14: 00007f95c9065000 R15: 00005575c7492c90 </TASK> irq event stamp: 5080 hardirqs last enabled at (5079): [<ffffffff83e0adb0>] _raw_spin_unlock_irqrestore+0x50/0x70 hardirqs last disabled at (5080): [<ffffffff83e0aa83>] _raw_spin_lock_irqsave+0x63/0x70 softirqs last enabled at (4182): [<ffffffff81516122>] handle_softirqs+0x552/0x710 softirqs last disabled at (4159): [<ffffffff815163f7>] __irq_exit_rcu+0x107/0x210 ---[ end trace 0000000000000000 ]--- The above was triggered by running on a kernel with both lockdep and KASAN as well as kmemleak enabled and executing the following command: # perf record -o perf-test.dat -a -- trace-cmd record --nosplice -e all -p function hackbench 50 With perf interjecting a lot of interrupts and trace-cmd enabling all events as well as function tracing, with lockdep, KASAN and kmemleak enabled, it could cause an interrupt preempting an event being written to add enough event ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Use kvfree instead of kfree in amdgpu_gmc_get_nps_memranges() amdgpu_discovery_get_nps_info() internally allocates memory for ranges using kvcalloc(), which may use vmalloc() for large allocation. Using kfree() to release vmalloc memory will lead to a memory corruption. Use kvfree() to safely handle both kmalloc and vmalloc allocations. Compile tested only. Issue found using a prototype static analysis tool and code review.

In the Linux kernel, the following vulnerability has been resolved: scsi: smartpqi: Use is_kdump_kernel() to check for kdump The smartpqi driver checks the reset_devices variable to determine whether special adjustments need to be made for kdump. This has the effect that after a regular kexec reboot, some driver parameters such as max_transfer_size are much lower than usual. More importantly, kexec reboot tests have revealed memory corruption caused by the driver log being written to system memory after a kexec. Fix this by testing is_kdump_kernel() rather than reset_devices where appropriate.

In Sudo before 1.8.26, if pwfeedback is enabled in /etc/sudoers, users can trigger a stack-based buffer overflow in the privileged sudo process. (pwfeedback is a default setting in Linux Mint and elementary OS; however, it is NOT the default for upstream and many other packages, and would exist only if enabled by an administrator.) The attacker needs to deliver a long string to the stdin of getln() in tgetpass.c.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Add sanity check for OOB writes at silencing At silencing the playback URB packets in the implicit fb mode before the actual playback, we blindly assume that the received packets fit with the buffer size. But when the setup in the capture stream differs from the playback stream (e.g. due to the USB core limitation of max packet size), such an inconsistency may lead to OOB writes to the buffer, resulting in a crash. For addressing it, add a sanity check of the transfer buffer size at prepare_silent_urb(), and stop the data copy if the received data overflows. Also, report back the transfer error properly from there, too. Note that this doesn't fix the root cause of the playback error itself, but this merely covers the kernel Oops.

In the Linux kernel, the following vulnerability has been resolved: net: lan743x: fix potential out-of-bounds write in lan743x_ptp_io_event_clock_get() Before calling lan743x_ptp_io_event_clock_get(), the 'channel' value is checked against the maximum value of PCI11X1X_PTP_IO_MAX_CHANNELS(8). This seems correct and aligns with the PTP interrupt status register (PTP_INT_STS) specifications. However, lan743x_ptp_io_event_clock_get() writes to ptp->extts[] with only LAN743X_PTP_N_EXTTS(4) elements, using channel as an index: lan743x_ptp_io_event_clock_get(..., u8 channel,...) { ... /* Update Local timestamp */ extts = &ptp->extts[channel]; extts->ts.tv_sec = sec; ... } To avoid an out-of-bounds write and utilize all the supported GPIO inputs, set LAN743X_PTP_N_EXTTS to 8. Detected using the static analysis tool - Svace.