In the Linux kernel, the following vulnerability has been resolved: sched_ext: Fix invalid irq restore in scx_ops_bypass() While adding outer irqsave/restore locking, 0e7ffff1b811 ("scx: Fix raciness in scx_ops_bypass()") forgot to convert an inner rq_unlock_irqrestore() to rq_unlock() which could re-enable IRQ prematurely leading to the following warning: raw_local_irq_restore() called with IRQs enabled WARNING: CPU: 1 PID: 96 at kernel/locking/irqflag-debug.c:10 warn_bogus_irq_restore+0x30/0x40 ... Sched_ext: create_dsq (enabling) pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : warn_bogus_irq_restore+0x30/0x40 lr : warn_bogus_irq_restore+0x30/0x40 ... Call trace: warn_bogus_irq_restore+0x30/0x40 (P) warn_bogus_irq_restore+0x30/0x40 (L) scx_ops_bypass+0x224/0x3b8 scx_ops_enable.isra.0+0x2c8/0xaa8 bpf_scx_reg+0x18/0x30 ... irq event stamp: 33739 hardirqs last enabled at (33739): [<ffff8000800b699c>] scx_ops_bypass+0x174/0x3b8 hardirqs last disabled at (33738): [<ffff800080d48ad4>] _raw_spin_lock_irqsave+0xb4/0xd8 Drop the stray _irqrestore().

In the Linux kernel, the following vulnerability has been resolved: tipc: do not update mtu if msg_max is too small in mtu negotiation When doing link mtu negotiation, a malicious peer may send Activate msg with a very small mtu, e.g. 4 in Shuang's testing, without checking for the minimum mtu, l->mtu will be set to 4 in tipc_link_proto_rcv(), then n->links[bearer_id].mtu is set to 4294967228, which is a overflow of '4 - INT_H_SIZE - EMSG_OVERHEAD' in tipc_link_mss(). With tipc_link.mtu = 4, tipc_link_xmit() kept printing the warning: tipc: Too large msg, purging xmit list 1 5 0 40 4! tipc: Too large msg, purging xmit list 1 15 0 60 4! And with tipc_link_entry.mtu 4294967228, a huge skb was allocated in named_distribute(), and when purging it in tipc_link_xmit(), a crash was even caused: general protection fault, probably for non-canonical address 0x2100001011000dd: 0000 [#1] PREEMPT SMP PTI CPU: 0 PID: 0 Comm: swapper/0 Kdump: loaded Not tainted 6.3.0.neta #19 RIP: 0010:kfree_skb_list_reason+0x7e/0x1f0 Call Trace: <IRQ> skb_release_data+0xf9/0x1d0 kfree_skb_reason+0x40/0x100 tipc_link_xmit+0x57a/0x740 [tipc] tipc_node_xmit+0x16c/0x5c0 [tipc] tipc_named_node_up+0x27f/0x2c0 [tipc] tipc_node_write_unlock+0x149/0x170 [tipc] tipc_rcv+0x608/0x740 [tipc] tipc_udp_recv+0xdc/0x1f0 [tipc] udp_queue_rcv_one_skb+0x33e/0x620 udp_unicast_rcv_skb.isra.72+0x75/0x90 __udp4_lib_rcv+0x56d/0xc20 ip_protocol_deliver_rcu+0x100/0x2d0 This patch fixes it by checking the new mtu against tipc_bearer_min_mtu(), and not updating mtu if it is too small.

In the Linux kernel, the following vulnerability has been resolved: net: avoid potential underflow in qdisc_pkt_len_init() with UFO After commit 7c6d2ecbda83 ("net: be more gentle about silly gso requests coming from user") virtio_net_hdr_to_skb() had sanity check to detect malicious attempts from user space to cook a bad GSO packet. Then commit cf9acc90c80ec ("net: virtio_net_hdr_to_skb: count transport header in UFO") while fixing one issue, allowed user space to cook a GSO packet with the following characteristic : IPv4 SKB_GSO_UDP, gso_size=3, skb->len = 28. When this packet arrives in qdisc_pkt_len_init(), we end up with hdr_len = 28 (IPv4 header + UDP header), matching skb->len Then the following sets gso_segs to 0 : gso_segs = DIV_ROUND_UP(skb->len - hdr_len, shinfo->gso_size); Then later we set qdisc_skb_cb(skb)->pkt_len to back to zero :/ qdisc_skb_cb(skb)->pkt_len += (gso_segs - 1) * hdr_len; This leads to the following crash in fq_codel [1] qdisc_pkt_len_init() is best effort, we only want an estimation of the bytes sent on the wire, not crashing the kernel. This patch is fixing this particular issue, a following one adds more sanity checks for another potential bug. [1] [ 70.724101] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 70.724561] #PF: supervisor read access in kernel mode [ 70.724561] #PF: error_code(0x0000) - not-present page [ 70.724561] PGD 10ac61067 P4D 10ac61067 PUD 107ee2067 PMD 0 [ 70.724561] Oops: Oops: 0000 [#1] SMP NOPTI [ 70.724561] CPU: 11 UID: 0 PID: 2163 Comm: b358537762 Not tainted 6.11.0-virtme #991 [ 70.724561] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 70.724561] RIP: 0010:fq_codel_enqueue (net/sched/sch_fq_codel.c:120 net/sched/sch_fq_codel.c:168 net/sched/sch_fq_codel.c:230) sch_fq_codel [ 70.724561] Code: 24 08 49 c1 e1 06 44 89 7c 24 18 45 31 ed 45 31 c0 31 ff 89 44 24 14 4c 03 8b 90 01 00 00 eb 04 39 ca 73 37 4d 8b 39 83 c7 01 <49> 8b 17 49 89 11 41 8b 57 28 45 8b 5f 34 49 c7 07 00 00 00 00 49 All code ======== 0: 24 08 and $0x8,%al 2: 49 c1 e1 06 shl $0x6,%r9 6: 44 89 7c 24 18 mov %r15d,0x18(%rsp) b: 45 31 ed xor %r13d,%r13d e: 45 31 c0 xor %r8d,%r8d 11: 31 ff xor %edi,%edi 13: 89 44 24 14 mov %eax,0x14(%rsp) 17: 4c 03 8b 90 01 00 00 add 0x190(%rbx),%r9 1e: eb 04 jmp 0x24 20: 39 ca cmp %ecx,%edx 22: 73 37 jae 0x5b 24: 4d 8b 39 mov (%r9),%r15 27: 83 c7 01 add $0x1,%edi 2a:* 49 8b 17 mov (%r15),%rdx <-- trapping instruction 2d: 49 89 11 mov %rdx,(%r9) 30: 41 8b 57 28 mov 0x28(%r15),%edx 34: 45 8b 5f 34 mov 0x34(%r15),%r11d 38: 49 c7 07 00 00 00 00 movq $0x0,(%r15) 3f: 49 rex.WB Code starting with the faulting instruction =========================================== 0: 49 8b 17 mov (%r15),%rdx 3: 49 89 11 mov %rdx,(%r9) 6: 41 8b 57 28 mov 0x28(%r15),%edx a: 45 8b 5f 34 mov 0x34(%r15),%r11d e: 49 c7 07 00 00 00 00 movq $0x0,(%r15) 15: 49 rex.WB [ 70.724561] RSP: 0018:ffff95ae85e6fb90 EFLAGS: 00000202 [ 70.724561] RAX: 0000000002000000 RBX: ffff95ae841de000 RCX: 0000000000000000 [ 70.724561] RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000001 [ 70.724561] RBP: ffff95ae85e6fbf8 R08: 0000000000000000 R09: ffff95b710a30000 [ 70.724561] R10: 0000000000000000 R11: bdf289445ce31881 R12: ffff95ae85e6fc58 [ 70.724561] R13: 0000000000000000 R14: 0000000000000040 R15: 0000000000000000 [ 70.724561] FS: 000000002c5c1380(0000) GS:ffff95bd7fcc0000(0000) knlGS:0000000000000000 [ 70.724561] CS: 0010 DS: 0000 ES: 0000 C ---truncated---

In the Linux kernel, the following vulnerability has been resolved: bpf: support non-r10 register spill/fill to/from stack in precision tracking Use instruction (jump) history to record instructions that performed register spill/fill to/from stack, regardless if this was done through read-only r10 register, or any other register after copying r10 into it *and* potentially adjusting offset. To make this work reliably, we push extra per-instruction flags into instruction history, encoding stack slot index (spi) and stack frame number in extra 10 bit flags we take away from prev_idx in instruction history. We don't touch idx field for maximum performance, as it's checked most frequently during backtracking. This change removes basically the last remaining practical limitation of precision backtracking logic in BPF verifier. It fixes known deficiencies, but also opens up new opportunities to reduce number of verified states, explored in the subsequent patches. There are only three differences in selftests' BPF object files according to veristat, all in the positive direction (less states). File Program Insns (A) Insns (B) Insns (DIFF) States (A) States (B) States (DIFF) -------------------------------------- ------------- --------- --------- ------------- ---------- ---------- ------------- test_cls_redirect_dynptr.bpf.linked3.o cls_redirect 2987 2864 -123 (-4.12%) 240 231 -9 (-3.75%) xdp_synproxy_kern.bpf.linked3.o syncookie_tc 82848 82661 -187 (-0.23%) 5107 5073 -34 (-0.67%) xdp_synproxy_kern.bpf.linked3.o syncookie_xdp 85116 84964 -152 (-0.18%) 5162 5130 -32 (-0.62%) Note, I avoided renaming jmp_history to more generic insn_hist to minimize number of lines changed and potential merge conflicts between bpf and bpf-next trees. Notice also cur_hist_entry pointer reset to NULL at the beginning of instruction verification loop. This pointer avoids the problem of relying on last jump history entry's insn_idx to determine whether we already have entry for current instruction or not. It can happen that we added jump history entry because current instruction is_jmp_point(), but also we need to add instruction flags for stack access. In this case, we don't want to entries, so we need to reuse last added entry, if it is present. Relying on insn_idx comparison has the same ambiguity problem as the one that was fixed recently in [0], so we avoid that. [0] https://patchwork.kernel.org/project/netdevbpf/patch/20231110002638.4168352-3-andrii@kernel.org/

In the Linux kernel, the following vulnerability has been resolved: skbuff: skb_segment, Call zero copy functions before using skbuff frags Commit bf5c25d60861 ("skbuff: in skb_segment, call zerocopy functions once per nskb") added the call to zero copy functions in skb_segment(). The change introduced a bug in skb_segment() because skb_orphan_frags() may possibly change the number of fragments or allocate new fragments altogether leaving nrfrags and frag to point to the old values. This can cause a panic with stacktrace like the one below. [ 193.894380] BUG: kernel NULL pointer dereference, address: 00000000000000bc [ 193.895273] CPU: 13 PID: 18164 Comm: vh-net-17428 Kdump: loaded Tainted: G O 5.15.123+ #26 [ 193.903919] RIP: 0010:skb_segment+0xb0e/0x12f0 [ 194.021892] Call Trace: [ 194.027422] <TASK> [ 194.072861] tcp_gso_segment+0x107/0x540 [ 194.082031] inet_gso_segment+0x15c/0x3d0 [ 194.090783] skb_mac_gso_segment+0x9f/0x110 [ 194.095016] __skb_gso_segment+0xc1/0x190 [ 194.103131] netem_enqueue+0x290/0xb10 [sch_netem] [ 194.107071] dev_qdisc_enqueue+0x16/0x70 [ 194.110884] __dev_queue_xmit+0x63b/0xb30 [ 194.121670] bond_start_xmit+0x159/0x380 [bonding] [ 194.128506] dev_hard_start_xmit+0xc3/0x1e0 [ 194.131787] __dev_queue_xmit+0x8a0/0xb30 [ 194.138225] macvlan_start_xmit+0x4f/0x100 [macvlan] [ 194.141477] dev_hard_start_xmit+0xc3/0x1e0 [ 194.144622] sch_direct_xmit+0xe3/0x280 [ 194.147748] __dev_queue_xmit+0x54a/0xb30 [ 194.154131] tap_get_user+0x2a8/0x9c0 [tap] [ 194.157358] tap_sendmsg+0x52/0x8e0 [tap] [ 194.167049] handle_tx_zerocopy+0x14e/0x4c0 [vhost_net] [ 194.173631] handle_tx+0xcd/0xe0 [vhost_net] [ 194.176959] vhost_worker+0x76/0xb0 [vhost] [ 194.183667] kthread+0x118/0x140 [ 194.190358] ret_from_fork+0x1f/0x30 [ 194.193670] </TASK> In this case calling skb_orphan_frags() updated nr_frags leaving nrfrags local variable in skb_segment() stale. This resulted in the code hitting i >= nrfrags prematurely and trying to move to next frag_skb using list_skb pointer, which was NULL, and caused kernel panic. Move the call to zero copy functions before using frags and nr_frags.

In the Linux kernel, the following vulnerability has been resolved: btrfs: insert tree mod log move in push_node_left There is a fairly unlikely race condition in tree mod log rewind that can result in a kernel panic which has the following trace: [530.569] BTRFS critical (device sda3): unable to find logical 0 length 4096 [530.585] BTRFS critical (device sda3): unable to find logical 0 length 4096 [530.602] BUG: kernel NULL pointer dereference, address: 0000000000000002 [530.618] #PF: supervisor read access in kernel mode [530.629] #PF: error_code(0x0000) - not-present page [530.641] PGD 0 P4D 0 [530.647] Oops: 0000 [#1] SMP [530.654] CPU: 30 PID: 398973 Comm: below Kdump: loaded Tainted: G S O K 5.12.0-0_fbk13_clang_7455_gb24de3bdb045 #1 [530.680] Hardware name: Quanta Mono Lake-M.2 SATA 1HY9U9Z001G/Mono Lake-M.2 SATA, BIOS F20_3A15 08/16/2017 [530.703] RIP: 0010:__btrfs_map_block+0xaa/0xd00 [530.755] RSP: 0018:ffffc9002c2f7600 EFLAGS: 00010246 [530.767] RAX: ffffffffffffffea RBX: ffff888292e41000 RCX: f2702d8b8be15100 [530.784] RDX: ffff88885fda6fb8 RSI: ffff88885fd973c8 RDI: ffff88885fd973c8 [530.800] RBP: ffff888292e410d0 R08: ffffffff82fd7fd0 R09: 00000000fffeffff [530.816] R10: ffffffff82e57fd0 R11: ffffffff82e57d70 R12: 0000000000000000 [530.832] R13: 0000000000001000 R14: 0000000000001000 R15: ffffc9002c2f76f0 [530.848] FS: 00007f38d64af000(0000) GS:ffff88885fd80000(0000) knlGS:0000000000000000 [530.866] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [530.880] CR2: 0000000000000002 CR3: 00000002b6770004 CR4: 00000000003706e0 [530.896] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [530.912] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [530.928] Call Trace: [530.934] ? btrfs_printk+0x13b/0x18c [530.943] ? btrfs_bio_counter_inc_blocked+0x3d/0x130 [530.955] btrfs_map_bio+0x75/0x330 [530.963] ? kmem_cache_alloc+0x12a/0x2d0 [530.973] ? btrfs_submit_metadata_bio+0x63/0x100 [530.984] btrfs_submit_metadata_bio+0xa4/0x100 [530.995] submit_extent_page+0x30f/0x360 [531.004] read_extent_buffer_pages+0x49e/0x6d0 [531.015] ? submit_extent_page+0x360/0x360 [531.025] btree_read_extent_buffer_pages+0x5f/0x150 [531.037] read_tree_block+0x37/0x60 [531.046] read_block_for_search+0x18b/0x410 [531.056] btrfs_search_old_slot+0x198/0x2f0 [531.066] resolve_indirect_ref+0xfe/0x6f0 [531.076] ? ulist_alloc+0x31/0x60 [531.084] ? kmem_cache_alloc_trace+0x12e/0x2b0 [531.095] find_parent_nodes+0x720/0x1830 [531.105] ? ulist_alloc+0x10/0x60 [531.113] iterate_extent_inodes+0xea/0x370 [531.123] ? btrfs_previous_extent_item+0x8f/0x110 [531.134] ? btrfs_search_path_in_tree+0x240/0x240 [531.146] iterate_inodes_from_logical+0x98/0xd0 [531.157] ? btrfs_search_path_in_tree+0x240/0x240 [531.168] btrfs_ioctl_logical_to_ino+0xd9/0x180 [531.179] btrfs_ioctl+0xe2/0x2eb0 This occurs when logical inode resolution takes a tree mod log sequence number, and then while backref walking hits a rewind on a busy node which has the following sequence of tree mod log operations (numbers filled in from a specific example, but they are somewhat arbitrary) REMOVE_WHILE_FREEING slot 532 REMOVE_WHILE_FREEING slot 531 REMOVE_WHILE_FREEING slot 530 ... REMOVE_WHILE_FREEING slot 0 REMOVE slot 455 REMOVE slot 454 REMOVE slot 453 ... REMOVE slot 0 ADD slot 455 ADD slot 454 ADD slot 453 ... ADD slot 0 MOVE src slot 0 -> dst slot 456 nritems 533 REMOVE slot 455 REMOVE slot 454 REMOVE slot 453 ... REMOVE slot 0 When this sequence gets applied via btrfs_tree_mod_log_rewind, it allocates a fresh rewind eb, and first inserts the correct key info for the 533 elements, then overwrites the first 456 of them, then decrements the count by 456 via the add ops, then rewinds the move by doing a memmove from 456:988->0:532. We have never written anything past 532, ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net_sched: sch_sfq: don't allow 1 packet limit The current implementation does not work correctly with a limit of 1. iproute2 actually checks for this and this patch adds the check in kernel as well. This fixes the following syzkaller reported crash: UBSAN: array-index-out-of-bounds in net/sched/sch_sfq.c:210:6 index 65535 is out of range for type 'struct sfq_head[128]' CPU: 0 PID: 2569 Comm: syz-executor101 Not tainted 5.10.0-smp-DEV #1 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 Call Trace: __dump_stack lib/dump_stack.c:79 [inline] dump_stack+0x125/0x19f lib/dump_stack.c:120 ubsan_epilogue lib/ubsan.c:148 [inline] __ubsan_handle_out_of_bounds+0xed/0x120 lib/ubsan.c:347 sfq_link net/sched/sch_sfq.c:210 [inline] sfq_dec+0x528/0x600 net/sched/sch_sfq.c:238 sfq_dequeue+0x39b/0x9d0 net/sched/sch_sfq.c:500 sfq_reset+0x13/0x50 net/sched/sch_sfq.c:525 qdisc_reset+0xfe/0x510 net/sched/sch_generic.c:1026 tbf_reset+0x3d/0x100 net/sched/sch_tbf.c:319 qdisc_reset+0xfe/0x510 net/sched/sch_generic.c:1026 dev_reset_queue+0x8c/0x140 net/sched/sch_generic.c:1296 netdev_for_each_tx_queue include/linux/netdevice.h:2350 [inline] dev_deactivate_many+0x6dc/0xc20 net/sched/sch_generic.c:1362 __dev_close_many+0x214/0x350 net/core/dev.c:1468 dev_close_many+0x207/0x510 net/core/dev.c:1506 unregister_netdevice_many+0x40f/0x16b0 net/core/dev.c:10738 unregister_netdevice_queue+0x2be/0x310 net/core/dev.c:10695 unregister_netdevice include/linux/netdevice.h:2893 [inline] __tun_detach+0x6b6/0x1600 drivers/net/tun.c:689 tun_detach drivers/net/tun.c:705 [inline] tun_chr_close+0x104/0x1b0 drivers/net/tun.c:3640 __fput+0x203/0x840 fs/file_table.c:280 task_work_run+0x129/0x1b0 kernel/task_work.c:185 exit_task_work include/linux/task_work.h:33 [inline] do_exit+0x5ce/0x2200 kernel/exit.c:931 do_group_exit+0x144/0x310 kernel/exit.c:1046 __do_sys_exit_group kernel/exit.c:1057 [inline] __se_sys_exit_group kernel/exit.c:1055 [inline] __x64_sys_exit_group+0x3b/0x40 kernel/exit.c:1055 do_syscall_64+0x6c/0xd0 entry_SYSCALL_64_after_hwframe+0x61/0xcb RIP: 0033:0x7fe5e7b52479 Code: Unable to access opcode bytes at RIP 0x7fe5e7b5244f. RSP: 002b:00007ffd3c800398 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fe5e7b52479 RDX: 000000000000003c RSI: 00000000000000e7 RDI: 0000000000000000 RBP: 00007fe5e7bcd2d0 R08: ffffffffffffffb8 R09: 0000000000000014 R10: 0000000000000000 R11: 0000000000000246 R12: 00007fe5e7bcd2d0 R13: 0000000000000000 R14: 00007fe5e7bcdd20 R15: 00007fe5e7b24270 The crash can be also be reproduced with the following (with a tc recompiled to allow for sfq limits of 1): tc qdisc add dev dummy0 handle 1: root tbf rate 1Kbit burst 100b lat 1s ../iproute2-6.9.0/tc/tc qdisc add dev dummy0 handle 2: parent 1:10 sfq limit 1 ifconfig dummy0 up ping -I dummy0 -f -c2 -W0.1 8.8.8.8 sleep 1 Scenario that triggers the crash: * the first packet is sent and queued in TBF and SFQ; qdisc qlen is 1 * TBF dequeues: it peeks from SFQ which moves the packet to the gso_skb list and keeps qdisc qlen set to 1. TBF is out of tokens so it schedules itself for later. * the second packet is sent and TBF tries to queues it to SFQ. qdisc qlen is now 2 and because the SFQ limit is 1 the packet is dropped by SFQ. At this point qlen is 1, and all of the SFQ slots are empty, however q->tail is not NULL. At this point, assuming no more packets are queued, when sch_dequeue runs again it will decrement the qlen for the current empty slot causing an underflow and the subsequent out of bounds access.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix crash caused by calling __xfrm_state_delete() twice The km.state is not checked in driver's delayed work. When xfrm_state_check_expire() is called, the state can be reset to XFRM_STATE_EXPIRED, even if it is XFRM_STATE_DEAD already. This happens when xfrm state is deleted, but not freed yet. As __xfrm_state_delete() is called again in xfrm timer, the following crash occurs. To fix this issue, skip xfrm_state_check_expire() if km.state is not XFRM_STATE_VALID. Oops: general protection fault, probably for non-canonical address 0xdead000000000108: 0000 [#1] SMP CPU: 5 UID: 0 PID: 7448 Comm: kworker/u102:2 Not tainted 6.11.0-rc2+ #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Workqueue: mlx5e_ipsec: eth%d mlx5e_ipsec_handle_sw_limits [mlx5_core] RIP: 0010:__xfrm_state_delete+0x3d/0x1b0 Code: 0f 84 8b 01 00 00 48 89 fd c6 87 c8 00 00 00 05 48 8d bb 40 10 00 00 e8 11 04 1a 00 48 8b 95 b8 00 00 00 48 8b 85 c0 00 00 00 <48> 89 42 08 48 89 10 48 8b 55 10 48 b8 00 01 00 00 00 00 ad de 48 RSP: 0018:ffff88885f945ec8 EFLAGS: 00010246 RAX: dead000000000122 RBX: ffffffff82afa940 RCX: 0000000000000036 RDX: dead000000000100 RSI: 0000000000000000 RDI: ffffffff82afb980 RBP: ffff888109a20340 R08: ffff88885f945ea0 R09: 0000000000000000 R10: 0000000000000000 R11: ffff88885f945ff8 R12: 0000000000000246 R13: ffff888109a20340 R14: ffff88885f95f420 R15: ffff88885f95f400 FS: 0000000000000000(0000) GS:ffff88885f940000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f2163102430 CR3: 00000001128d6001 CR4: 0000000000370eb0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <IRQ> ? die_addr+0x33/0x90 ? exc_general_protection+0x1a2/0x390 ? asm_exc_general_protection+0x22/0x30 ? __xfrm_state_delete+0x3d/0x1b0 ? __xfrm_state_delete+0x2f/0x1b0 xfrm_timer_handler+0x174/0x350 ? __xfrm_state_delete+0x1b0/0x1b0 __hrtimer_run_queues+0x121/0x270 hrtimer_run_softirq+0x88/0xd0 handle_softirqs+0xcc/0x270 do_softirq+0x3c/0x50 </IRQ> <TASK> __local_bh_enable_ip+0x47/0x50 mlx5e_ipsec_handle_sw_limits+0x7d/0x90 [mlx5_core] process_one_work+0x137/0x2d0 worker_thread+0x28d/0x3a0 ? rescuer_thread+0x480/0x480 kthread+0xb8/0xe0 ? kthread_park+0x80/0x80 ret_from_fork+0x2d/0x50 ? kthread_park+0x80/0x80 ret_from_fork_asm+0x11/0x20 </TASK>

In the Linux kernel, the following vulnerability has been resolved: HID: hid-thrustmaster: Fix warning in thrustmaster_probe by adding endpoint check syzbot has found a type mismatch between a USB pipe and the transfer endpoint, which is triggered by the hid-thrustmaster driver[1]. There is a number of similar, already fixed issues [2]. In this case as in others, implementing check for endpoint type fixes the issue. [1] https://syzkaller.appspot.com/bug?extid=040e8b3db6a96908d470 [2] https://syzkaller.appspot.com/bug?extid=348331f63b034f89b622

In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Fix crash during unbind if gpio unit is in use We used the wrong device for the device managed functions. We used the usb device, when we should be using the interface device. If we unbind the driver from the usb interface, the cleanup functions are never called. In our case, the IRQ is never disabled. If an IRQ is triggered, it will try to access memory sections that are already free, causing an OOPS. We cannot use the function devm_request_threaded_irq here. The devm_* clean functions may be called after the main structure is released by uvc_delete. Luckily this bug has small impact, as it is only affected by devices with gpio units and the user has to unbind the device, a disconnect will not trigger this error.

In the Linux kernel, the following vulnerability has been resolved: serial: 8250: Reinit port->pm on port specific driver unbind When we unbind a serial port hardware specific 8250 driver, the generic serial8250 driver takes over the port. After that we see an oops about 10 seconds later. This can produce the following at least on some TI SoCs: Unhandled fault: imprecise external abort (0x1406) Internal error: : 1406 [#1] SMP ARM Turns out that we may still have the serial port hardware specific driver port->pm in use, and serial8250_pm() tries to call it after the port specific driver is gone: serial8250_pm [8250_base] from uart_change_pm+0x54/0x8c [serial_base] uart_change_pm [serial_base] from uart_hangup+0x154/0x198 [serial_base] uart_hangup [serial_base] from __tty_hangup.part.0+0x328/0x37c __tty_hangup.part.0 from disassociate_ctty+0x154/0x20c disassociate_ctty from do_exit+0x744/0xaac do_exit from do_group_exit+0x40/0x8c do_group_exit from __wake_up_parent+0x0/0x1c Let's fix the issue by calling serial8250_set_defaults() in serial8250_unregister_port(). This will set the port back to using the serial8250 default functions, and sets the port->pm to point to serial8250_pm.

In the Linux kernel, the following vulnerability has been resolved: octeontx2-pf: Avoid use of GFP_KERNEL in atomic context Using GFP_KERNEL in preemption disable context, causing below warning when CONFIG_DEBUG_ATOMIC_SLEEP is enabled. [ 32.542271] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:274 [ 32.550883] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1, name: swapper/0 [ 32.558707] preempt_count: 1, expected: 0 [ 32.562710] RCU nest depth: 0, expected: 0 [ 32.566800] CPU: 3 PID: 1 Comm: swapper/0 Tainted: G W 6.2.0-rc2-00269-gae9dcb91c606 #7 [ 32.576188] Hardware name: Marvell CN106XX board (DT) [ 32.581232] Call trace: [ 32.583670] dump_backtrace.part.0+0xe0/0xf0 [ 32.587937] show_stack+0x18/0x30 [ 32.591245] dump_stack_lvl+0x68/0x84 [ 32.594900] dump_stack+0x18/0x34 [ 32.598206] __might_resched+0x12c/0x160 [ 32.602122] __might_sleep+0x48/0xa0 [ 32.605689] __kmem_cache_alloc_node+0x2b8/0x2e0 [ 32.610301] __kmalloc+0x58/0x190 [ 32.613610] otx2_sq_aura_pool_init+0x1a8/0x314 [ 32.618134] otx2_open+0x1d4/0x9d0 To avoid use of GFP_ATOMIC for memory allocation, disable preemption after all memory allocation is done.

In the Linux kernel, the following vulnerability has been resolved: media: mdp3: Fix resource leaks in of_find_device_by_node Use put_device to release the object get through of_find_device_by_node, avoiding resource leaks.

In the Linux kernel, the following vulnerability has been resolved: spi: bcm-qspi: return error if neither hif_mspi nor mspi is available If neither a "hif_mspi" nor "mspi" resource is present, the driver will just early exit in probe but still return success. Apart from not doing anything meaningful, this would then also lead to a null pointer access on removal, as platform_get_drvdata() would return NULL, which it would then try to dereference when trying to unregister the spi master. Fix this by unconditionally calling devm_ioremap_resource(), as it can handle a NULL res and will then return a viable ERR_PTR() if we get one. The "return 0;" was previously a "goto qspi_resource_err;" where then ret was returned, but since ret was still initialized to 0 at this place this was a valid conversion in 63c5395bb7a9 ("spi: bcm-qspi: Fix use-after-free on unbind"). The issue was not introduced by this commit, only made more obvious.

In the Linux kernel, the following vulnerability has been resolved: RDMA/rxe: Fix incomplete state save in rxe_requester If a send packet is dropped by the IP layer in rxe_requester() the call to rxe_xmit_packet() can fail with err == -EAGAIN. To recover, the state of the wqe is restored to the state before the packet was sent so it can be resent. However, the routines that save and restore the state miss a significnt part of the variable state in the wqe, the dma struct which is used to process through the sge table. And, the state is not saved before the packet is built which modifies the dma struct. Under heavy stress testing with many QPs on a fast node sending large messages to a slow node dropped packets are observed and the resent packets are corrupted because the dma struct was not restored. This patch fixes this behavior and allows the test cases to succeed.

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: dp: Only trigger DRM HPD events if bridge is attached The MediaTek DisplayPort interface bridge driver starts its interrupts as soon as its probed. However when the interrupts trigger the bridge might not have been attached to a DRM device. As drm_helper_hpd_irq_event() does not check whether the passed in drm_device is valid or not, a NULL pointer passed in results in a kernel NULL pointer dereference in it. Check whether the bridge is attached and only trigger an HPD event if it is.

In the Linux kernel, the following vulnerability has been resolved: ipv6: Add lwtunnel encap size of all siblings in nexthop calculation In function rt6_nlmsg_size(), the length of nexthop is calculated by multipling the nexthop length of fib6_info and the number of siblings. However if the fib6_info has no lwtunnel but the siblings have lwtunnels, the nexthop length is less than it should be, and it will trigger a warning in inet6_rt_notify() as follows: WARNING: CPU: 0 PID: 6082 at net/ipv6/route.c:6180 inet6_rt_notify+0x120/0x130 ...... Call Trace: <TASK> fib6_add_rt2node+0x685/0xa30 fib6_add+0x96/0x1b0 ip6_route_add+0x50/0xd0 inet6_rtm_newroute+0x97/0xa0 rtnetlink_rcv_msg+0x156/0x3d0 netlink_rcv_skb+0x5a/0x110 netlink_unicast+0x246/0x350 netlink_sendmsg+0x250/0x4c0 sock_sendmsg+0x66/0x70 ___sys_sendmsg+0x7c/0xd0 __sys_sendmsg+0x5d/0xb0 do_syscall_64+0x3f/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc This bug can be reproduced by script: ip -6 addr add 2002::2/64 dev ens2 ip -6 route add 100::/64 via 2002::1 dev ens2 metric 100 for i in 10 20 30 40 50 60 70; do ip link add link ens2 name ipv_$i type ipvlan ip -6 addr add 2002::$i/64 dev ipv_$i ifconfig ipv_$i up done for i in 10 20 30 40 50 60; do ip -6 route append 100::/64 encap ip6 dst 2002::$i via 2002::1 dev ipv_$i metric 100 done ip -6 route append 100::/64 via 2002::1 dev ipv_70 metric 100 This patch fixes it by adding nexthop_len of every siblings using rt6_nh_nlmsg_size().

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix calltrace warning in amddrm_buddy_fini The following call trace is observed when removing the amdgpu driver, which is caused by that BOs allocated for psp are not freed until removing. [61811.450562] RIP: 0010:amddrm_buddy_fini.cold+0x29/0x47 [amddrm_buddy] [61811.450577] Call Trace: [61811.450577] <TASK> [61811.450579] amdgpu_vram_mgr_fini+0x135/0x1c0 [amdgpu] [61811.450728] amdgpu_ttm_fini+0x207/0x290 [amdgpu] [61811.450870] amdgpu_bo_fini+0x27/0xa0 [amdgpu] [61811.451012] gmc_v9_0_sw_fini+0x4a/0x60 [amdgpu] [61811.451166] amdgpu_device_fini_sw+0x117/0x520 [amdgpu] [61811.451306] amdgpu_driver_release_kms+0x16/0x30 [amdgpu] [61811.451447] devm_drm_dev_init_release+0x4d/0x80 [drm] [61811.451466] devm_action_release+0x15/0x20 [61811.451469] release_nodes+0x40/0xb0 [61811.451471] devres_release_all+0x9b/0xd0 [61811.451473] __device_release_driver+0x1bb/0x2a0 [61811.451476] driver_detach+0xf3/0x140 [61811.451479] bus_remove_driver+0x6c/0xf0 [61811.451481] driver_unregister+0x31/0x60 [61811.451483] pci_unregister_driver+0x40/0x90 [61811.451486] amdgpu_exit+0x15/0x447 [amdgpu] For smu v13_0_2, if the GPU supports xgmi, refer to commit f5c7e7797060 ("drm/amdgpu: Adjust removal control flow for smu v13_0_2"), it will run gpu recover in AMDGPU_RESET_FOR_DEVICE_REMOVE mode when removing, which makes all devices in hive list have hw reset but no resume except the basic ip blocks, then other ip blocks will not call .hw_fini according to ip_block.status.hw. Since psp_free_shared_bufs just includes some software operations, so move it to psp_sw_fini.

In the Linux kernel, the following vulnerability has been resolved: USB: ULPI: fix memory leak with using debugfs_lookup() When calling debugfs_lookup() the result must have dput() called on it, otherwise the memory will leak over time. To make things simpler, just call debugfs_lookup_and_remove() instead which handles all of the logic at once.

In the Linux kernel, the following vulnerability has been resolved: scsi: scsi_dh_alua: Fix memleak for 'qdata' in alua_activate() If alua_rtpg_queue() failed from alua_activate(), then 'qdata' is not freed, which will cause following memleak: unreferenced object 0xffff88810b2c6980 (size 32): comm "kworker/u16:2", pid 635322, jiffies 4355801099 (age 1216426.076s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 40 39 24 c1 ff ff ff ff 00 f8 ea 0a 81 88 ff ff @9$............. backtrace: [<0000000098f3a26d>] alua_activate+0xb0/0x320 [<000000003b529641>] scsi_dh_activate+0xb2/0x140 [<000000007b296db3>] activate_path_work+0xc6/0xe0 [dm_multipath] [<000000007adc9ace>] process_one_work+0x3c5/0x730 [<00000000c457a985>] worker_thread+0x93/0x650 [<00000000cb80e628>] kthread+0x1ba/0x210 [<00000000a1e61077>] ret_from_fork+0x22/0x30 Fix the problem by freeing 'qdata' in error path.

In the Linux kernel, the following vulnerability has been resolved: USB: fotg210: fix memory leak with using debugfs_lookup() When calling debugfs_lookup() the result must have dput() called on it, otherwise the memory will leak over time. To make things simpler, just call debugfs_lookup_and_remove() instead which handles all of the logic at once.

In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: avoid possible NULL skb pointer dereference In 'mwifiex_handle_uap_rx_forward()', always check the value returned by 'skb_copy()' to avoid potential NULL pointer dereference in 'mwifiex_uap_queue_bridged_pkt()', and drop original skb in case of copying failure. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: ALSA: memalloc: prefer dma_mapping_error() over explicit address checking With CONFIG_DMA_API_DEBUG enabled, the following warning is observed: DMA-API: snd_hda_intel 0000:03:00.1: device driver failed to check map error[device address=0x00000000ffff0000] [size=20480 bytes] [mapped as single] WARNING: CPU: 28 PID: 2255 at kernel/dma/debug.c:1036 check_unmap+0x1408/0x2430 CPU: 28 UID: 42 PID: 2255 Comm: wireplumber Tainted: G W L 6.12.0-10-133577cad6bf48e5a7848c4338124081393bfe8a+ #759 debug_dma_unmap_page+0xe9/0xf0 snd_dma_wc_free+0x85/0x130 [snd_pcm] snd_pcm_lib_free_pages+0x1e3/0x440 [snd_pcm] snd_pcm_common_ioctl+0x1c9a/0x2960 [snd_pcm] snd_pcm_ioctl+0x6a/0xc0 [snd_pcm] ... Check for returned DMA addresses using specialized dma_mapping_error() helper which is generally recommended for this purpose by Documentation/core-api/dma-api.rst.

In the Linux kernel, the following vulnerability has been resolved: media: bdisp: Add missing check for create_workqueue Add the check for the return value of the create_workqueue in order to avoid NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: sctp: check send stream number after wait_for_sndbuf This patch fixes a corner case where the asoc out stream count may change after wait_for_sndbuf. When the main thread in the client starts a connection, if its out stream count is set to N while the in stream count in the server is set to N - 2, another thread in the client keeps sending the msgs with stream number N - 1, and waits for sndbuf before processing INIT_ACK. However, after processing INIT_ACK, the out stream count in the client is shrunk to N - 2, the same to the in stream count in the server. The crash occurs when the thread waiting for sndbuf is awake and sends the msg in a non-existing stream(N - 1), the call trace is as below: KASAN: null-ptr-deref in range [0x0000000000000038-0x000000000000003f] Call Trace: <TASK> sctp_cmd_send_msg net/sctp/sm_sideeffect.c:1114 [inline] sctp_cmd_interpreter net/sctp/sm_sideeffect.c:1777 [inline] sctp_side_effects net/sctp/sm_sideeffect.c:1199 [inline] sctp_do_sm+0x197d/0x5310 net/sctp/sm_sideeffect.c:1170 sctp_primitive_SEND+0x9f/0xc0 net/sctp/primitive.c:163 sctp_sendmsg_to_asoc+0x10eb/0x1a30 net/sctp/socket.c:1868 sctp_sendmsg+0x8d4/0x1d90 net/sctp/socket.c:2026 inet_sendmsg+0x9d/0xe0 net/ipv4/af_inet.c:825 sock_sendmsg_nosec net/socket.c:722 [inline] sock_sendmsg+0xde/0x190 net/socket.c:745 The fix is to add an unlikely check for the send stream number after the thread wakes up from the wait_for_sndbuf.

In the Linux kernel, the following vulnerability has been resolved: cgroup/cpuset: Fix wrong check in update_parent_subparts_cpumask() It was found that the check to see if a partition could use up all the cpus from the parent cpuset in update_parent_subparts_cpumask() was incorrect. As a result, it is possible to leave parent with no effective cpu left even if there are tasks in the parent cpuset. This can lead to system panic as reported in [1]. Fix this probem by updating the check to fail the enabling the partition if parent's effective_cpus is a subset of the child's cpus_allowed. Also record the error code when an error happens in update_prstate() and add a test case where parent partition and child have the same cpu list and parent has task. Enabling partition in the child will fail in this case. [1] https://www.spinics.net/lists/cgroups/msg36254.html

In the Linux kernel, the following vulnerability has been resolved: nfsd: don't replace page in rq_pages if it's a continuation of last page The splice read calls nfsd_splice_actor to put the pages containing file data into the svc_rqst->rq_pages array. It's possible however to get a splice result that only has a partial page at the end, if (e.g.) the filesystem hands back a short read that doesn't cover the whole page. nfsd_splice_actor will plop the partial page into its rq_pages array and return. Then later, when nfsd_splice_actor is called again, the remainder of the page may end up being filled out. At this point, nfsd_splice_actor will put the page into the array _again_ corrupting the reply. If this is done enough times, rq_next_page will overrun the array and corrupt the trailing fields -- the rq_respages and rq_next_page pointers themselves. If we've already added the page to the array in the last pass, don't add it to the array a second time when dealing with a splice continuation. This was originally handled properly in nfsd_splice_actor, but commit 91e23b1c3982 ("NFSD: Clean up nfsd_splice_actor()") removed the check for it.

In the Linux kernel, the following vulnerability has been resolved: io_uring: prevent reg-wait speculations With *ENTER_EXT_ARG_REG instead of passing a user pointer with arguments for the waiting loop the user can specify an offset into a pre-mapped region of memory, in which case the [offset, offset + sizeof(io_uring_reg_wait)) will be intepreted as the argument. As we address a kernel array using a user given index, it'd be a subject to speculation type of exploits. Use array_index_nospec() to prevent that. Make sure to pass not the full region size but truncate by the maximum offset allowed considering the structure size.

In the Linux kernel, the following vulnerability has been resolved: net: usb: smsc95xx: Limit packet length to skb->len Packet length retrieved from descriptor may be larger than the actual socket buffer length. In such case the cloned skb passed up the network stack will leak kernel memory contents.

In the Linux kernel, the following vulnerability has been resolved: sctp: add a refcnt in sctp_stream_priorities to avoid a nested loop With this refcnt added in sctp_stream_priorities, we don't need to traverse all streams to check if the prio is used by other streams when freeing one stream's prio in sctp_sched_prio_free_sid(). This can avoid a nested loop (up to 65535 * 65535), which may cause a stuck as Ying reported: watchdog: BUG: soft lockup - CPU#23 stuck for 26s! [ksoftirqd/23:136] Call Trace: <TASK> sctp_sched_prio_free_sid+0xab/0x100 [sctp] sctp_stream_free_ext+0x64/0xa0 [sctp] sctp_stream_free+0x31/0x50 [sctp] sctp_association_free+0xa5/0x200 [sctp] Note that it doesn't need to use refcount_t type for this counter, as its accessing is always protected under the sock lock. v1->v2: - add a check in sctp_sched_prio_set to avoid the possible prio_head refcnt overflow.

In the Linux kernel, the following vulnerability has been resolved: nfc: fix memory leak of se_io context in nfc_genl_se_io The callback context for sending/receiving APDUs to/from the selected secure element is allocated inside nfc_genl_se_io and supposed to be eventually freed in se_io_cb callback function. However, there are several error paths where the bwi_timer is not charged to call se_io_cb later, and the cb_context is leaked. The patch proposes to free the cb_context explicitly on those error paths. At the moment we can't simply check 'dev->ops->se_io()' return value as it may be negative in both cases: when the timer was charged and was not.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: unmap and remove csa_va properly Root PD BO should be reserved before unmap and remove a bo_va from VM otherwise lockdep will complain. v2: check fpriv->csa_va is not NULL instead of amdgpu_mcbp (christian) [14616.936827] WARNING: CPU: 6 PID: 1711 at drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c:1762 amdgpu_vm_bo_del+0x399/0x3f0 [amdgpu] [14616.937096] Call Trace: [14616.937097] <TASK> [14616.937102] amdgpu_driver_postclose_kms+0x249/0x2f0 [amdgpu] [14616.937187] drm_file_free+0x1d6/0x300 [drm] [14616.937207] drm_close_helper.isra.0+0x62/0x70 [drm] [14616.937220] drm_release+0x5e/0x100 [drm] [14616.937234] __fput+0x9f/0x280 [14616.937239] ____fput+0xe/0x20 [14616.937241] task_work_run+0x61/0x90 [14616.937246] exit_to_user_mode_prepare+0x215/0x220 [14616.937251] syscall_exit_to_user_mode+0x2a/0x60 [14616.937254] do_syscall_64+0x48/0x90 [14616.937257] entry_SYSCALL_64_after_hwframe+0x63/0xcd

In the Linux kernel, the following vulnerability has been resolved: drm: amd: display: Fix memory leakage This commit fixes memory leakage in dc_construct_ctx() function.

In the Linux kernel, the following vulnerability has been resolved: iommufd: Do not corrupt the pfn list when doing batch carry If batch->end is 0 then setting npfns[0] before computing the new value of pfns will fail to adjust the pfn and result in various page accounting corruptions. It should be ordered after. This seems to result in various kinds of page meta-data corruption related failures: WARNING: CPU: 1 PID: 527 at mm/gup.c:75 try_grab_folio+0x503/0x740 Modules linked in: CPU: 1 PID: 527 Comm: repro Not tainted 6.3.0-rc2-eeac8ede1755+ #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:try_grab_folio+0x503/0x740 Code: e3 01 48 89 de e8 6d c1 dd ff 48 85 db 0f 84 7c fe ff ff e8 4f bf dd ff 49 8d 47 ff 48 89 45 d0 e9 73 fe ff ff e8 3d bf dd ff <0f> 0b 31 db e9 d0 fc ff ff e8 2f bf dd ff 48 8b 5d c8 31 ff 48 89 RSP: 0018:ffffc90000f37908 EFLAGS: 00010046 RAX: 0000000000000000 RBX: 00000000fffffc02 RCX: ffffffff81504c26 RDX: 0000000000000000 RSI: ffff88800d030000 RDI: 0000000000000002 RBP: ffffc90000f37948 R08: 000000000003ca24 R09: 0000000000000008 R10: 000000000003ca00 R11: 0000000000000023 R12: ffffea000035d540 R13: 0000000000000001 R14: 0000000000000000 R15: ffffea000035d540 FS: 00007fecbf659740(0000) GS:ffff88807dd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000200011c3 CR3: 000000000ef66006 CR4: 0000000000770ee0 PKRU: 55555554 Call Trace: <TASK> internal_get_user_pages_fast+0xd32/0x2200 pin_user_pages_fast+0x65/0x90 pfn_reader_user_pin+0x376/0x390 pfn_reader_next+0x14a/0x7b0 pfn_reader_first+0x140/0x1b0 iopt_area_fill_domain+0x74/0x210 iopt_table_add_domain+0x30e/0x6e0 iommufd_device_selftest_attach+0x7f/0x140 iommufd_test+0x10ff/0x16f0 iommufd_fops_ioctl+0x206/0x330 __x64_sys_ioctl+0x10e/0x160 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix sysfs interface lifetime The current nilfs2 sysfs support has issues with the timing of creation and deletion of sysfs entries, potentially leading to null pointer dereferences, use-after-free, and lockdep warnings. Some of the sysfs attributes for nilfs2 per-filesystem instance refer to metadata file "cpfile", "sufile", or "dat", but nilfs_sysfs_create_device_group that creates those attributes is executed before the inodes for these metadata files are loaded, and nilfs_sysfs_delete_device_group which deletes these sysfs entries is called after releasing their metadata file inodes. Therefore, access to some of these sysfs attributes may occur outside of the lifetime of these metadata files, resulting in inode NULL pointer dereferences or use-after-free. In addition, the call to nilfs_sysfs_create_device_group() is made during the locking period of the semaphore "ns_sem" of nilfs object, so the shrinker call caused by the memory allocation for the sysfs entries, may derive lock dependencies "ns_sem" -> (shrinker) -> "locks acquired in nilfs_evict_inode()". Since nilfs2 may acquire "ns_sem" deep in the call stack holding other locks via its error handler __nilfs_error(), this causes lockdep to report circular locking. This is a false positive and no circular locking actually occurs as no inodes exist yet when nilfs_sysfs_create_device_group() is called. Fortunately, the lockdep warnings can be resolved by simply moving the call to nilfs_sysfs_create_device_group() out of "ns_sem". This fixes these sysfs issues by revising where the device's sysfs interface is created/deleted and keeping its lifetime within the lifetime of the metadata files above.

In the Linux kernel, the following vulnerability has been resolved: bonding: do not assume skb mac_header is set Drivers must not assume in their ndo_start_xmit() that skbs have their mac_header set. skb->data is all what is needed. bonding seems to be one of the last offender as caught by syzbot: WARNING: CPU: 1 PID: 12155 at include/linux/skbuff.h:2907 skb_mac_offset include/linux/skbuff.h:2913 [inline] WARNING: CPU: 1 PID: 12155 at include/linux/skbuff.h:2907 bond_xmit_hash drivers/net/bonding/bond_main.c:4170 [inline] WARNING: CPU: 1 PID: 12155 at include/linux/skbuff.h:2907 bond_xmit_3ad_xor_slave_get drivers/net/bonding/bond_main.c:5149 [inline] WARNING: CPU: 1 PID: 12155 at include/linux/skbuff.h:2907 bond_3ad_xor_xmit drivers/net/bonding/bond_main.c:5186 [inline] WARNING: CPU: 1 PID: 12155 at include/linux/skbuff.h:2907 __bond_start_xmit drivers/net/bonding/bond_main.c:5442 [inline] WARNING: CPU: 1 PID: 12155 at include/linux/skbuff.h:2907 bond_start_xmit+0x14ab/0x19d0 drivers/net/bonding/bond_main.c:5470 Modules linked in: CPU: 1 PID: 12155 Comm: syz-executor.3 Not tainted 6.1.30-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/25/2023 RIP: 0010:skb_mac_header include/linux/skbuff.h:2907 [inline] RIP: 0010:skb_mac_offset include/linux/skbuff.h:2913 [inline] RIP: 0010:bond_xmit_hash drivers/net/bonding/bond_main.c:4170 [inline] RIP: 0010:bond_xmit_3ad_xor_slave_get drivers/net/bonding/bond_main.c:5149 [inline] RIP: 0010:bond_3ad_xor_xmit drivers/net/bonding/bond_main.c:5186 [inline] RIP: 0010:__bond_start_xmit drivers/net/bonding/bond_main.c:5442 [inline] RIP: 0010:bond_start_xmit+0x14ab/0x19d0 drivers/net/bonding/bond_main.c:5470 Code: 8b 7c 24 30 e8 76 dd 1a 01 48 85 c0 74 0d 48 89 c3 e8 29 67 2e fe e9 15 ef ff ff e8 1f 67 2e fe e9 10 ef ff ff e8 15 67 2e fe <0f> 0b e9 45 f8 ff ff e8 09 67 2e fe e9 dc fa ff ff e8 ff 66 2e fe RSP: 0018:ffffc90002fff6e0 EFLAGS: 00010283 RAX: ffffffff835874db RBX: 000000000000ffff RCX: 0000000000040000 RDX: ffffc90004dcf000 RSI: 00000000000000b5 RDI: 00000000000000b6 RBP: ffffc90002fff8b8 R08: ffffffff83586d16 R09: ffffffff83586584 R10: 0000000000000007 R11: ffff8881599fc780 R12: ffff88811b6a7b7e R13: 1ffff110236d4f6f R14: ffff88811b6a7ac0 R15: 1ffff110236d4f76 FS: 00007f2e9eb47700(0000) GS:ffff8881f6b00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000001b2e421000 CR3: 000000010e6d4000 CR4: 00000000003526e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> [<ffffffff8471a49f>] netdev_start_xmit include/linux/netdevice.h:4925 [inline] [<ffffffff8471a49f>] __dev_direct_xmit+0x4ef/0x850 net/core/dev.c:4380 [<ffffffff851d845b>] dev_direct_xmit include/linux/netdevice.h:3043 [inline] [<ffffffff851d845b>] packet_direct_xmit+0x18b/0x300 net/packet/af_packet.c:284 [<ffffffff851c7472>] packet_snd net/packet/af_packet.c:3112 [inline] [<ffffffff851c7472>] packet_sendmsg+0x4a22/0x64d0 net/packet/af_packet.c:3143 [<ffffffff8467a4b2>] sock_sendmsg_nosec net/socket.c:716 [inline] [<ffffffff8467a4b2>] sock_sendmsg net/socket.c:736 [inline] [<ffffffff8467a4b2>] __sys_sendto+0x472/0x5f0 net/socket.c:2139 [<ffffffff8467a715>] __do_sys_sendto net/socket.c:2151 [inline] [<ffffffff8467a715>] __se_sys_sendto net/socket.c:2147 [inline] [<ffffffff8467a715>] __x64_sys_sendto+0xe5/0x100 net/socket.c:2147 [<ffffffff8553071f>] do_syscall_x64 arch/x86/entry/common.c:50 [inline] [<ffffffff8553071f>] do_syscall_64+0x2f/0x50 arch/x86/entry/common.c:80 [<ffffffff85600087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd

In the Linux kernel, the following vulnerability has been resolved: kobject: Add sanity check for kset->kobj.ktype in kset_register() When I register a kset in the following way: static struct kset my_kset; kobject_set_name(&my_kset.kobj, "my_kset"); ret = kset_register(&my_kset); A null pointer dereference exception is occurred: [ 4453.568337] Unable to handle kernel NULL pointer dereference at \ virtual address 0000000000000028 ... ... [ 4453.810361] Call trace: [ 4453.813062] kobject_get_ownership+0xc/0x34 [ 4453.817493] kobject_add_internal+0x98/0x274 [ 4453.822005] kset_register+0x5c/0xb4 [ 4453.825820] my_kobj_init+0x44/0x1000 [my_kset] ... ... Because I didn't initialize my_kset.kobj.ktype. According to the description in Documentation/core-api/kobject.rst: - A ktype is the type of object that embeds a kobject. Every structure that embeds a kobject needs a corresponding ktype. So add sanity check to make sure kset->kobj.ktype is not NULL.

In the Linux kernel, the following vulnerability has been resolved: drm/i915: Fix memory leaks in i915 selftests This patch fixes memory leaks on error escapes in function fake_get_pages (cherry picked from commit 8bfbdadce85c4c51689da10f39c805a7106d4567)

In the Linux kernel, the following vulnerability has been resolved: cpu/hotplug: Don't offline the last non-isolated CPU If a system has isolated CPUs via the "isolcpus=" command line parameter, then an attempt to offline the last housekeeping CPU will result in a WARN_ON() when rebuilding the scheduler domains and a subsequent panic due to and unhandled empty CPU mas in partition_sched_domains_locked(). cpuset_hotplug_workfn() rebuild_sched_domains_locked() ndoms = generate_sched_domains(&doms, &attr); cpumask_and(doms[0], top_cpuset.effective_cpus, housekeeping_cpumask(HK_FLAG_DOMAIN)); Thus results in an empty CPU mask which triggers the warning and then the subsequent crash: WARNING: CPU: 4 PID: 80 at kernel/sched/topology.c:2366 build_sched_domains+0x120c/0x1408 Call trace: build_sched_domains+0x120c/0x1408 partition_sched_domains_locked+0x234/0x880 rebuild_sched_domains_locked+0x37c/0x798 rebuild_sched_domains+0x30/0x58 cpuset_hotplug_workfn+0x2a8/0x930 Unable to handle kernel paging request at virtual address fffe80027ab37080 partition_sched_domains_locked+0x318/0x880 rebuild_sched_domains_locked+0x37c/0x798 Aside of the resulting crash, it does not make any sense to offline the last last housekeeping CPU. Prevent this by masking out the non-housekeeping CPUs when selecting a target CPU for initiating the CPU unplug operation via the work queue.

In the Linux kernel, the following vulnerability has been resolved: nfs: Fix oops in nfs_netfs_init_request() when copying to cache When netfslib wants to copy some data that has just been read on behalf of nfs, it creates a new write request and calls nfs_netfs_init_request() to initialise it, but with a NULL file pointer. This causes nfs_file_open_context() to oops - however, we don't actually need the nfs context as we're only going to write to the cache. Fix this by just returning if we aren't given a file pointer and emit a warning if the request was for something other than copy-to-cache. Further, fix nfs_netfs_free_request() so that it doesn't try to free the context if the pointer is NULL.

In the Linux kernel, the following vulnerability has been resolved: media: nuvoton: Fix an error check in npcm_video_ece_init() When function of_find_device_by_node() fails, it returns NULL instead of an error code. So the corresponding error check logic should be modified to check whether the return value is NULL and set the error code to be returned as -ENODEV.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (pmbus_core) Fix NULL pointer dereference Pass i2c_client to _pmbus_is_enabled to drop the assumption that a regulator device is passed in. This will fix the issue of a NULL pointer dereference when called from _pmbus_get_flags.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix i_disksize exceeding i_size problem in paritally written case It is possible for i_disksize can exceed i_size, triggering a warning. generic_perform_write copied = iov_iter_copy_from_user_atomic(len) // copied < len ext4_da_write_end | ext4_update_i_disksize | new_i_size = pos + copied; | WRITE_ONCE(EXT4_I(inode)->i_disksize, newsize) // update i_disksize | generic_write_end | copied = block_write_end(copied, len) // copied = 0 | if (unlikely(copied < len)) | if (!PageUptodate(page)) | copied = 0; | if (pos + copied > inode->i_size) // return false if (unlikely(copied == 0)) goto again; if (unlikely(iov_iter_fault_in_readable(i, bytes))) { status = -EFAULT; break; } We get i_disksize greater than i_size here, which could trigger WARNING check 'i_size_read(inode) < EXT4_I(inode)->i_disksize' while doing dio: ext4_dio_write_iter iomap_dio_rw __iomap_dio_rw // return err, length is not aligned to 512 ext4_handle_inode_extension WARN_ON_ONCE(i_size_read(inode) < EXT4_I(inode)->i_disksize) // Oops WARNING: CPU: 2 PID: 2609 at fs/ext4/file.c:319 CPU: 2 PID: 2609 Comm: aa Not tainted 6.3.0-rc2 RIP: 0010:ext4_file_write_iter+0xbc7 Call Trace: vfs_write+0x3b1 ksys_write+0x77 do_syscall_64+0x39 Fix it by updating 'copied' value before updating i_disksize just like ext4_write_inline_data_end() does. A reproducer can be found in the buganizer link below.

In the Linux kernel, the following vulnerability has been resolved: riscv: kprobe: Fixup kernel panic when probing an illegal position The kernel would panic when probed for an illegal position. eg: (CONFIG_RISCV_ISA_C=n) echo 'p:hello kernel_clone+0x16 a0=%a0' >> kprobe_events echo 1 > events/kprobes/hello/enable cat trace Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: __do_sys_newfstatat+0xb8/0xb8 CPU: 0 PID: 111 Comm: sh Not tainted 6.2.0-rc1-00027-g2d398fe49a4d #490 Hardware name: riscv-virtio,qemu (DT) Call Trace: [<ffffffff80007268>] dump_backtrace+0x38/0x48 [<ffffffff80c5e83c>] show_stack+0x50/0x68 [<ffffffff80c6da28>] dump_stack_lvl+0x60/0x84 [<ffffffff80c6da6c>] dump_stack+0x20/0x30 [<ffffffff80c5ecf4>] panic+0x160/0x374 [<ffffffff80c6db94>] generic_handle_arch_irq+0x0/0xa8 [<ffffffff802deeb0>] sys_newstat+0x0/0x30 [<ffffffff800158c0>] sys_clone+0x20/0x30 [<ffffffff800039e8>] ret_from_syscall+0x0/0x4 ---[ end Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: __do_sys_newfstatat+0xb8/0xb8 ]--- That is because the kprobe's ebreak instruction broke the kernel's original code. The user should guarantee the correction of the probe position, but it couldn't make the kernel panic. This patch adds arch_check_kprobe in arch_prepare_kprobe to prevent an illegal position (Such as the middle of an instruction).

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix possible underflow for displays with large vblank [Why] Underflow observed when using a display with a large vblank region and low refresh rate [How] Simplify calculation of vblank_nom Increase value for VBlankNomDefaultUS to 800us

In the Linux kernel, the following vulnerability has been resolved: ipv4: prevent potential spectre v1 gadget in ip_metrics_convert() if (!type) continue; if (type > RTAX_MAX) return -EINVAL; ... metrics[type - 1] = val; @type being used as an array index, we need to prevent cpu speculation or risk leaking kernel memory content.

In the Linux kernel, the following vulnerability has been resolved: ice: Don't tx before switchdev is fully configured There is possibility that ice_eswitch_port_start_xmit might be called while some resources are still not allocated which might cause NULL pointer dereference. Fix this by checking if switchdev configuration was finished.

In the Linux kernel, the following vulnerability has been resolved: clk: Fix memory leak in devm_clk_notifier_register() devm_clk_notifier_register() allocates a devres resource for clk notifier but didn't register that to the device, so the notifier didn't get unregistered on device detach and the allocated resource was leaked. Fix the issue by registering the resource through devres_add(). This issue was found with kmemleak on a Chromebook.

In the Linux kernel, the following vulnerability has been resolved: drm/panel: fix a possible null pointer dereference In versatile_panel_get_modes(), the return value of drm_mode_duplicate() is assigned to mode, which will lead to a NULL pointer dereference on failure of drm_mode_duplicate(). Add a check to avoid npd.

In the Linux kernel, the following vulnerability has been resolved: usb: xhci: tegra: fix sleep in atomic call When we set the dual-role port to Host mode, we observed the following splat: [ 167.057718] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:229 [ 167.057872] Workqueue: events tegra_xusb_usb_phy_work [ 167.057954] Call trace: [ 167.057962] dump_backtrace+0x0/0x210 [ 167.057996] show_stack+0x30/0x50 [ 167.058020] dump_stack_lvl+0x64/0x84 [ 167.058065] dump_stack+0x14/0x34 [ 167.058100] __might_resched+0x144/0x180 [ 167.058140] __might_sleep+0x64/0xd0 [ 167.058171] slab_pre_alloc_hook.constprop.0+0xa8/0x110 [ 167.058202] __kmalloc_track_caller+0x74/0x2b0 [ 167.058233] kvasprintf+0xa4/0x190 [ 167.058261] kasprintf+0x58/0x90 [ 167.058285] tegra_xusb_find_port_node.isra.0+0x58/0xd0 [ 167.058334] tegra_xusb_find_port+0x38/0xa0 [ 167.058380] tegra_xusb_padctl_get_usb3_companion+0x38/0xd0 [ 167.058430] tegra_xhci_id_notify+0x8c/0x1e0 [ 167.058473] notifier_call_chain+0x88/0x100 [ 167.058506] atomic_notifier_call_chain+0x44/0x70 [ 167.058537] tegra_xusb_usb_phy_work+0x60/0xd0 [ 167.058581] process_one_work+0x1dc/0x4c0 [ 167.058618] worker_thread+0x54/0x410 [ 167.058650] kthread+0x188/0x1b0 [ 167.058672] ret_from_fork+0x10/0x20 The function tegra_xusb_padctl_get_usb3_companion eventually calls tegra_xusb_find_port and this in turn calls kasprintf which might sleep and so cannot be called from an atomic context. Fix this by moving the call to tegra_xusb_padctl_get_usb3_companion to the tegra_xhci_id_work function where it is really needed.