In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: fix gtk offload status event locking The ath11k active pdevs are protected by RCU but the gtk offload status event handling code calling ath11k_mac_get_arvif_by_vdev_id() was not marked as a read-side critical section. Mark the code in question as an RCU read-side critical section to avoid any potential use-after-free issues. Compile tested only.

In the Linux kernel, the following vulnerability has been resolved: fs/jfs: Add validity check for db_maxag and db_agpref Both db_maxag and db_agpref are used as the index of the db_agfree array, but there is currently no validity check for db_maxag and db_agpref, which can lead to errors. The following is related bug reported by Syzbot: UBSAN: array-index-out-of-bounds in fs/jfs/jfs_dmap.c:639:20 index 7936 is out of range for type 'atomic_t[128]' Add checking that the values of db_maxag and db_agpref are valid indexes for the db_agfree array.

In the Linux kernel, the following vulnerability has been resolved: mctp: perform route lookups under a RCU read-side lock Our current route lookups (mctp_route_lookup and mctp_route_lookup_null) traverse the net's route list without the RCU read lock held. This means the route lookup is subject to preemption, resulting in an potential grace period expiry, and so an eventual kfree() while we still have the route pointer. Add the proper read-side critical section locks around the route lookups, preventing premption and a possible parallel kfree. The remaining net->mctp.routes accesses are already under a rcu_read_lock, or protected by the RTNL for updates. Based on an analysis from Sili Luo <rootlab@huawei.com>, where introducing a delay in the route lookup could cause a UAF on simultaneous sendmsg() and route deletion.

In the Linux kernel, the following vulnerability has been resolved: bnxt: prevent skb UAF after handing over to PTP worker When reading the timestamp is required bnxt_tx_int() hands over the ownership of the completed skb to the PTP worker. The skb should not be used afterwards, as the worker may run before the rest of our code and free the skb, leading to a use-after-free. Since dev_kfree_skb_any() accepts NULL make the loss of ownership more obvious and set skb to NULL.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix potential deadlock when releasing mids All release_mid() callers seem to hold a reference of @mid so there is no need to call kref_put(&mid->refcount, __release_mid) under @server->mid_lock spinlock. If they don't, then an use-after-free bug would have occurred anyways. By getting rid of such spinlock also fixes a potential deadlock as shown below CPU 0 CPU 1 ------------------------------------------------------------------ cifs_demultiplex_thread() cifs_debug_data_proc_show() release_mid() spin_lock(&server->mid_lock); spin_lock(&cifs_tcp_ses_lock) spin_lock(&server->mid_lock) __release_mid() smb2_find_smb_tcon() spin_lock(&cifs_tcp_ses_lock) *deadlock*

In the Linux kernel, the following vulnerability has been resolved: ice: arfs: fix use-after-free when freeing @rx_cpu_rmap The CI testing bots triggered the following splat: [ 718.203054] BUG: KASAN: use-after-free in free_irq_cpu_rmap+0x53/0x80 [ 718.206349] Read of size 4 at addr ffff8881bd127e00 by task sh/20834 [ 718.212852] CPU: 28 PID: 20834 Comm: sh Kdump: loaded Tainted: G S W IOE 5.17.0-rc8_nextqueue-devqueue-02643-g23f3121aca93 #1 [ 718.219695] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0012.070720200218 07/07/2020 [ 718.223418] Call Trace: [ 718.227139] [ 718.230783] dump_stack_lvl+0x33/0x42 [ 718.234431] print_address_description.constprop.9+0x21/0x170 [ 718.238177] ? free_irq_cpu_rmap+0x53/0x80 [ 718.241885] ? free_irq_cpu_rmap+0x53/0x80 [ 718.245539] kasan_report.cold.18+0x7f/0x11b [ 718.249197] ? free_irq_cpu_rmap+0x53/0x80 [ 718.252852] free_irq_cpu_rmap+0x53/0x80 [ 718.256471] ice_free_cpu_rx_rmap.part.11+0x37/0x50 [ice] [ 718.260174] ice_remove_arfs+0x5f/0x70 [ice] [ 718.263810] ice_rebuild_arfs+0x3b/0x70 [ice] [ 718.267419] ice_rebuild+0x39c/0xb60 [ice] [ 718.270974] ? asm_sysvec_apic_timer_interrupt+0x12/0x20 [ 718.274472] ? ice_init_phy_user_cfg+0x360/0x360 [ice] [ 718.278033] ? delay_tsc+0x4a/0xb0 [ 718.281513] ? preempt_count_sub+0x14/0xc0 [ 718.284984] ? delay_tsc+0x8f/0xb0 [ 718.288463] ice_do_reset+0x92/0xf0 [ice] [ 718.292014] ice_pci_err_resume+0x91/0xf0 [ice] [ 718.295561] pci_reset_function+0x53/0x80 <...> [ 718.393035] Allocated by task 690: [ 718.433497] Freed by task 20834: [ 718.495688] Last potentially related work creation: [ 718.568966] The buggy address belongs to the object at ffff8881bd127e00 which belongs to the cache kmalloc-96 of size 96 [ 718.574085] The buggy address is located 0 bytes inside of 96-byte region [ffff8881bd127e00, ffff8881bd127e60) [ 718.579265] The buggy address belongs to the page: [ 718.598905] Memory state around the buggy address: [ 718.601809] ffff8881bd127d00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc [ 718.604796] ffff8881bd127d80: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc [ 718.607794] >ffff8881bd127e00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc [ 718.610811] ^ [ 718.613819] ffff8881bd127e80: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc [ 718.617107] ffff8881bd127f00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc This is due to that free_irq_cpu_rmap() is always being called *after* (devm_)free_irq() and thus it tries to work with IRQ descs already freed. For example, on device reset the driver frees the rmap right before allocating a new one (the splat above). Make rmap creation and freeing function symmetrical with {request,free}_irq() calls i.e. do that on ifup/ifdown instead of device probe/remove/resume. These operations can be performed independently from the actual device aRFS configuration. Also, make sure ice_vsi_free_irq() clears IRQ affinity notifiers only when aRFS is disabled -- otherwise, CPU rmap sets and clears its own and they must not be touched manually.

In the Linux kernel, the following vulnerability has been resolved: reiserfs: Avoid touching renamed directory if parent does not change The VFS will not be locking moved directory if its parent does not change. Change reiserfs rename code to avoid touching renamed directory if its parent does not change as without locking that can corrupt the filesystem.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath9k: Fix potential array-index-out-of-bounds read in ath9k_htc_txstatus() Fix an array-index-out-of-bounds read in ath9k_htc_txstatus(). The bug occurs when txs->cnt, data from a URB provided by a USB device, is bigger than the size of the array txs->txstatus, which is HTC_MAX_TX_STATUS. WARN_ON() already checks it, but there is no bug handling code after the check. Make the function return if that is the case. Found by a modified version of syzkaller. UBSAN: array-index-out-of-bounds in htc_drv_txrx.c index 13 is out of range for type '__wmi_event_txstatus [12]' Call Trace: ath9k_htc_txstatus ath9k_wmi_event_tasklet tasklet_action_common __do_softirq irq_exit_rxu sysvec_apic_timer_interrupt

In the Linux kernel, the following vulnerability has been resolved: jfs: fix array-index-out-of-bounds in dbAdjTree Currently there is a bound check missing in the dbAdjTree while accessing the dmt_stree. To add the required check added the bool is_ctl which is required to determine the size as suggest in the following commit. https://lore.kernel.org/linux-kernel-mentees/f9475918-2186-49b8-b801-6f0f9e75f4fa@oracle.com/

A flaw use after free in the Linux kernel video4linux driver was found in the way user triggers em28xx_usb_probe() for the Empia 28xx based TV cards. A local user could use this flaw to crash the system or potentially escalate their privileges on the system.

In the Linux kernel, the following vulnerability has been resolved: drm/amd: check num of link levels when update pcie param In SR-IOV environment, the value of pcie_table->num_of_link_levels will be 0, and num_of_levels - 1 will cause array index out of bounds

In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix out-of-bounds access may occur when coalesce info is read via debugfs The hns3 driver define an array of string to show the coalesce info, but if the kernel adds a new mode or a new state, out-of-bounds access may occur when coalesce info is read via debugfs, this patch fix the problem.

In the Linux kernel, the following vulnerability has been resolved: crypto: scomp - fix req->dst buffer overflow The req->dst buffer size should be checked before copying from the scomp_scratch->dst to avoid req->dst buffer overflow problem.

In the Linux kernel, the following vulnerability has been resolved: RDMA/srp: Do not call scsi_done() from srp_abort() After scmd_eh_abort_handler() has called the SCSI LLD eh_abort_handler callback, it performs one of the following actions: * Call scsi_queue_insert(). * Call scsi_finish_command(). * Call scsi_eh_scmd_add(). Hence, SCSI abort handlers must not call scsi_done(). Otherwise all the above actions would trigger a use-after-free. Hence remove the scsi_done() call from srp_abort(). Keep the srp_free_req() call before returning SUCCESS because we may not see the command again if SUCCESS is returned.

In the Linux kernel, the following vulnerability has been resolved: jfs: fix uaf in jfs_evict_inode When the execution of diMount(ipimap) fails, the object ipimap that has been released may be accessed in diFreeSpecial(). Asynchronous ipimap release occurs when rcu_core() calls jfs_free_node(). Therefore, when diMount(ipimap) fails, sbi->ipimap should not be initialized as ipimap.

In the Linux kernel, the following vulnerability has been resolved: jfs: fix array-index-out-of-bounds in diAlloc Currently there is not check against the agno of the iag while allocating new inodes to avoid fragmentation problem. Added the check which is required.

In the Linux kernel, the following vulnerability has been resolved: media: mtk-jpeg: Fix use after free bug due to error path handling in mtk_jpeg_dec_device_run In mtk_jpeg_probe, &jpeg->job_timeout_work is bound with mtk_jpeg_job_timeout_work. In mtk_jpeg_dec_device_run, if error happens in mtk_jpeg_set_dec_dst, it will finally start the worker while mark the job as finished by invoking v4l2_m2m_job_finish. There are two methods to trigger the bug. If we remove the module, it which will call mtk_jpeg_remove to make cleanup. The possible sequence is as follows, which will cause a use-after-free bug. CPU0 CPU1 mtk_jpeg_dec_... | start worker | |mtk_jpeg_job_timeout_work mtk_jpeg_remove | v4l2_m2m_release | kfree(m2m_dev); | | | v4l2_m2m_get_curr_priv | m2m_dev->curr_ctx //use If we close the file descriptor, which will call mtk_jpeg_release, it will have a similar sequence. Fix this bug by starting timeout worker only if started jpegdec worker successfully. Then v4l2_m2m_job_finish will only be called in either mtk_jpeg_job_timeout_work or mtk_jpeg_dec_device_run.

In the Linux kernel, the following vulnerability has been resolved: binder: fix use-after-free in shinker's callback The mmap read lock is used during the shrinker's callback, which means that using alloc->vma pointer isn't safe as it can race with munmap(). As of commit dd2283f2605e ("mm: mmap: zap pages with read mmap_sem in munmap") the mmap lock is downgraded after the vma has been isolated. I was able to reproduce this issue by manually adding some delays and triggering page reclaiming through the shrinker's debug sysfs. The following KASAN report confirms the UAF: ================================================================== BUG: KASAN: slab-use-after-free in zap_page_range_single+0x470/0x4b8 Read of size 8 at addr ffff356ed50e50f0 by task bash/478 CPU: 1 PID: 478 Comm: bash Not tainted 6.6.0-rc5-00055-g1c8b86a3799f-dirty #70 Hardware name: linux,dummy-virt (DT) Call trace: zap_page_range_single+0x470/0x4b8 binder_alloc_free_page+0x608/0xadc __list_lru_walk_one+0x130/0x3b0 list_lru_walk_node+0xc4/0x22c binder_shrink_scan+0x108/0x1dc shrinker_debugfs_scan_write+0x2b4/0x500 full_proxy_write+0xd4/0x140 vfs_write+0x1ac/0x758 ksys_write+0xf0/0x1dc __arm64_sys_write+0x6c/0x9c Allocated by task 492: kmem_cache_alloc+0x130/0x368 vm_area_alloc+0x2c/0x190 mmap_region+0x258/0x18bc do_mmap+0x694/0xa60 vm_mmap_pgoff+0x170/0x29c ksys_mmap_pgoff+0x290/0x3a0 __arm64_sys_mmap+0xcc/0x144 Freed by task 491: kmem_cache_free+0x17c/0x3c8 vm_area_free_rcu_cb+0x74/0x98 rcu_core+0xa38/0x26d4 rcu_core_si+0x10/0x1c __do_softirq+0x2fc/0xd24 Last potentially related work creation: __call_rcu_common.constprop.0+0x6c/0xba0 call_rcu+0x10/0x1c vm_area_free+0x18/0x24 remove_vma+0xe4/0x118 do_vmi_align_munmap.isra.0+0x718/0xb5c do_vmi_munmap+0xdc/0x1fc __vm_munmap+0x10c/0x278 __arm64_sys_munmap+0x58/0x7c Fix this issue by performing instead a vma_lookup() which will fail to find the vma that was isolated before the mmap lock downgrade. Note that this option has better performance than upgrading to a mmap write lock which would increase contention. Plus, mmap_write_trylock() has been recently removed anyway.

VMware Tools (12.0.0, 11.x.y and 10.x.y) contains a local privilege escalation vulnerability. A malicious actor with local non-administrative access to the Guest OS can escalate privileges as a root user in the virtual machine.

In the Linux kernel, the following vulnerability has been resolved: net: atlantic: eliminate double free in error handling logic Driver has a logic leak in ring data allocation/free, where aq_ring_free could be called multiple times on same ring, if system is under stress and got memory allocation error. Ring pointer was used as an indicator of failure, but this is not correct since only ring data is allocated/deallocated. Ring itself is an array member. Changing ring allocation functions to return error code directly. This simplifies error handling and eliminates aq_ring_free on higher layer.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix slub overflow in ksmbd_decode_ntlmssp_auth_blob() If authblob->SessionKey.Length is bigger than session key size(CIFS_KEY_SIZE), slub overflow can happen in key exchange codes. cifs_arc4_crypt copy to session key array from SessionKey from client.

A double-free flaw was found in the Linux kernel’s TUN/TAP device driver functionality in how a user registers the device when the register_netdevice function fails (NETDEV_REGISTER notifier). This flaw allows a local user to crash or potentially escalate their privileges on the system.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix the error handler of rfkill config When the core rfkill config throws error, it should free the allocated resources. Currently it is not freeing the core pdev create resources. Avoid this issue by calling the core pdev destroy in the error handler of core rfkill config. Found this issue in the code review and it is compile tested only.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/pm: fix a double-free in si_dpm_init When the allocation of adev->pm.dpm.dyn_state.vddc_dependency_on_dispclk.entries fails, amdgpu_free_extended_power_table is called to free some fields of adev. However, when the control flow returns to si_dpm_sw_init, it goes to label dpm_failed and calls si_dpm_fini, which calls amdgpu_free_extended_power_table again and free those fields again. Thus a double-free is triggered.

In the Linux kernel, the following vulnerability has been resolved: of: Fix double free in of_parse_phandle_with_args_map In of_parse_phandle_with_args_map() the inner loop that iterates through the map entries calls of_node_put(new) to free the reference acquired by the previous iteration of the inner loop. This assumes that the value of "new" is NULL on the first iteration of the inner loop. Make sure that this is true in all iterations of the outer loop by setting "new" to NULL after its value is assigned to "cur". Extend the unittest to detect the double free and add an additional test case that actually triggers this path.

In the Linux kernel, the following vulnerability has been resolved: uio: Fix use-after-free in uio_open core-1 core-2 ------------------------------------------------------- uio_unregister_device uio_open idev = idr_find() device_unregister(&idev->dev) put_device(&idev->dev) uio_device_release get_device(&idev->dev) kfree(idev) uio_free_minor(minor) uio_release put_device(&idev->dev) kfree(idev) ------------------------------------------------------- In the core-1 uio_unregister_device(), the device_unregister will kfree idev when the idev->dev kobject ref is 1. But after core-1 device_unregister, put_device and before doing kfree, the core-2 may get_device. Then: 1. After core-1 kfree idev, the core-2 will do use-after-free for idev. 2. When core-2 do uio_release and put_device, the idev will be double freed. To address this issue, we can get idev atomic & inc idev reference with minor_lock.

In the Linux kernel, the following vulnerability has been resolved: x86/srso: Add SRSO mitigation for Hygon processors Add mitigation for the speculative return stack overflow vulnerability which exists on Hygon processors too.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix out of bounds in init_smb2_rsp_hdr() If client send smb2 negotiate request and then send smb1 negotiate request, init_smb2_rsp_hdr is called for smb1 negotiate request since need_neg is set to false. This patch ignore smb1 packets after ->need_neg is set to false.

An out-of-bounds access issue was found in the Linux kernel sound subsystem. It could occur when the 'id->name' provided by the user did not end with '\0'. A privileged local user could pass a specially crafted name through ioctl() interface and crash the system or potentially escalate their privileges on the system.

In the Linux kernel, the following vulnerability has been resolved: EDAC/thunderx: Fix possible out-of-bounds string access Enabling -Wstringop-overflow globally exposes a warning for a common bug in the usage of strncat(): drivers/edac/thunderx_edac.c: In function 'thunderx_ocx_com_threaded_isr': drivers/edac/thunderx_edac.c:1136:17: error: 'strncat' specified bound 1024 equals destination size [-Werror=stringop-overflow=] 1136 | strncat(msg, other, OCX_MESSAGE_SIZE); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ... 1145 | strncat(msg, other, OCX_MESSAGE_SIZE); ... 1150 | strncat(msg, other, OCX_MESSAGE_SIZE); ... Apparently the author of this driver expected strncat() to behave the way that strlcat() does, which uses the size of the destination buffer as its third argument rather than the length of the source buffer. The result is that there is no check on the size of the allocated buffer. Change it to strlcat(). [ bp: Trim compiler output, fixup commit message. ]

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: Fix a memory corruption issue A few lines above, space is kzalloc()'ed for: sizeof(struct iwl_nvm_data) + sizeof(struct ieee80211_channel) + sizeof(struct ieee80211_rate) 'mvm->nvm_data' is a 'struct iwl_nvm_data', so it is fine. At the end of this structure, there is the 'channels' flex array. Each element is of type 'struct ieee80211_channel'. So only 1 element is allocated in this array. When doing: mvm->nvm_data->bands[0].channels = mvm->nvm_data->channels; We point at the first element of the 'channels' flex array. So this is fine. However, when doing: mvm->nvm_data->bands[0].bitrates = (void *)((u8 *)mvm->nvm_data->channels + 1); because of the "(u8 *)" cast, we add only 1 to the address of the beginning of the flex array. It is likely that we want point at the 'struct ieee80211_rate' allocated just after. Remove the spurious casting so that the pointer arithmetic works as expected.

In the Linux kernel, the following vulnerability has been resolved: PM / devfreq: Fix buffer overflow in trans_stat_show Fix buffer overflow in trans_stat_show(). Convert simple snprintf to the more secure scnprintf with size of PAGE_SIZE. Add condition checking if we are exceeding PAGE_SIZE and exit early from loop. Also add at the end a warning that we exceeded PAGE_SIZE and that stats is disabled. Return -EFBIG in the case where we don't have enough space to write the full transition table. Also document in the ABI that this function can return -EFBIG error.

A use-after-free vulnerability in the Linux kernel's netfilter: nf_tables component can be exploited to achieve local privilege escalation. Addition and removal of rules from chain bindings within the same transaction causes leads to use-after-free. We recommend upgrading past commit f15f29fd4779be8a418b66e9d52979bb6d6c2325.

A flaw was found in the Linux kernel before 5.9-rc4. Memory corruption can be exploited to gain root privileges from unprivileged processes. The highest threat from this vulnerability is to data confidentiality and integrity.

In the Linux kernel, the following vulnerability has been resolved: iommu: Don't reserve 0-length IOVA region When the bootloader/firmware doesn't setup the framebuffers, their address and size are 0 in "iommu-addresses" property. If IOVA region is reserved with 0 length, then it ends up corrupting the IOVA rbtree with an entry which has pfn_hi < pfn_lo. If we intend to use display driver in kernel without framebuffer then it's causing the display IOMMU mappings to fail as entire valid IOVA space is reserved when address and length are passed as 0. An ideal solution would be firmware removing the "iommu-addresses" property and corresponding "memory-region" if display is not present. But the kernel should be able to handle this by checking for size of IOVA region and skipping the IOVA reservation if size is 0. Also, add a warning if firmware is requesting 0-length IOVA region reservation.

In the Linux kernel, the following vulnerability has been resolved: can: j1939: Fix UAF in j1939_sk_match_filter during setsockopt(SO_J1939_FILTER) Lock jsk->sk to prevent UAF when setsockopt(..., SO_J1939_FILTER, ...) modifies jsk->filters while receiving packets. Following trace was seen on affected system: ================================================================== BUG: KASAN: slab-use-after-free in j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939] Read of size 4 at addr ffff888012144014 by task j1939/350 CPU: 0 PID: 350 Comm: j1939 Tainted: G W OE 6.5.0-rc5 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 Call Trace: print_report+0xd3/0x620 ? kasan_complete_mode_report_info+0x7d/0x200 ? j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939] kasan_report+0xc2/0x100 ? j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939] __asan_load4+0x84/0xb0 j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939] j1939_sk_recv+0x20b/0x320 [can_j1939] ? __kasan_check_write+0x18/0x20 ? __pfx_j1939_sk_recv+0x10/0x10 [can_j1939] ? j1939_simple_recv+0x69/0x280 [can_j1939] ? j1939_ac_recv+0x5e/0x310 [can_j1939] j1939_can_recv+0x43f/0x580 [can_j1939] ? __pfx_j1939_can_recv+0x10/0x10 [can_j1939] ? raw_rcv+0x42/0x3c0 [can_raw] ? __pfx_j1939_can_recv+0x10/0x10 [can_j1939] can_rcv_filter+0x11f/0x350 [can] can_receive+0x12f/0x190 [can] ? __pfx_can_rcv+0x10/0x10 [can] can_rcv+0xdd/0x130 [can] ? __pfx_can_rcv+0x10/0x10 [can] __netif_receive_skb_one_core+0x13d/0x150 ? __pfx___netif_receive_skb_one_core+0x10/0x10 ? __kasan_check_write+0x18/0x20 ? _raw_spin_lock_irq+0x8c/0xe0 __netif_receive_skb+0x23/0xb0 process_backlog+0x107/0x260 __napi_poll+0x69/0x310 net_rx_action+0x2a1/0x580 ? __pfx_net_rx_action+0x10/0x10 ? __pfx__raw_spin_lock+0x10/0x10 ? handle_irq_event+0x7d/0xa0 __do_softirq+0xf3/0x3f8 do_softirq+0x53/0x80 </IRQ> <TASK> __local_bh_enable_ip+0x6e/0x70 netif_rx+0x16b/0x180 can_send+0x32b/0x520 [can] ? __pfx_can_send+0x10/0x10 [can] ? __check_object_size+0x299/0x410 raw_sendmsg+0x572/0x6d0 [can_raw] ? __pfx_raw_sendmsg+0x10/0x10 [can_raw] ? apparmor_socket_sendmsg+0x2f/0x40 ? __pfx_raw_sendmsg+0x10/0x10 [can_raw] sock_sendmsg+0xef/0x100 sock_write_iter+0x162/0x220 ? __pfx_sock_write_iter+0x10/0x10 ? __rtnl_unlock+0x47/0x80 ? security_file_permission+0x54/0x320 vfs_write+0x6ba/0x750 ? __pfx_vfs_write+0x10/0x10 ? __fget_light+0x1ca/0x1f0 ? __rcu_read_unlock+0x5b/0x280 ksys_write+0x143/0x170 ? __pfx_ksys_write+0x10/0x10 ? __kasan_check_read+0x15/0x20 ? fpregs_assert_state_consistent+0x62/0x70 __x64_sys_write+0x47/0x60 do_syscall_64+0x60/0x90 ? do_syscall_64+0x6d/0x90 ? irqentry_exit+0x3f/0x50 ? exc_page_fault+0x79/0xf0 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Allocated by task 348: kasan_save_stack+0x2a/0x50 kasan_set_track+0x29/0x40 kasan_save_alloc_info+0x1f/0x30 __kasan_kmalloc+0xb5/0xc0 __kmalloc_node_track_caller+0x67/0x160 j1939_sk_setsockopt+0x284/0x450 [can_j1939] __sys_setsockopt+0x15c/0x2f0 __x64_sys_setsockopt+0x6b/0x80 do_syscall_64+0x60/0x90 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Freed by task 349: kasan_save_stack+0x2a/0x50 kasan_set_track+0x29/0x40 kasan_save_free_info+0x2f/0x50 __kasan_slab_free+0x12e/0x1c0 __kmem_cache_free+0x1b9/0x380 kfree+0x7a/0x120 j1939_sk_setsockopt+0x3b2/0x450 [can_j1939] __sys_setsockopt+0x15c/0x2f0 __x64_sys_setsockopt+0x6b/0x80 do_syscall_64+0x60/0x90 entry_SYSCALL_64_after_hwframe+0x6e/0xd8

In the Linux kernel, the following vulnerability has been resolved: crypto: s390/aes - Fix buffer overread in CTR mode When processing the last block, the s390 ctr code will always read a whole block, even if there isn't a whole block of data left. Fix this by using the actual length left and copy it into a buffer first for processing.

In the Linux kernel, the following vulnerability has been resolved: drivers/amd/pm: fix a use-after-free in kv_parse_power_table When ps allocated by kzalloc equals to NULL, kv_parse_power_table frees adev->pm.dpm.ps that allocated before. However, after the control flow goes through the following call chains: kv_parse_power_table |-> kv_dpm_init |-> kv_dpm_sw_init |-> kv_dpm_fini The adev->pm.dpm.ps is used in the for loop of kv_dpm_fini after its first free in kv_parse_power_table and causes a use-after-free bug.

In the Linux kernel, the following vulnerability has been resolved: bpf: Check rcu_read_lock_trace_held() before calling bpf map helpers These three bpf_map_{lookup,update,delete}_elem() helpers are also available for sleepable bpf program, so add the corresponding lock assertion for sleepable bpf program, otherwise the following warning will be reported when a sleepable bpf program manipulates bpf map under interpreter mode (aka bpf_jit_enable=0): WARNING: CPU: 3 PID: 4985 at kernel/bpf/helpers.c:40 ...... CPU: 3 PID: 4985 Comm: test_progs Not tainted 6.6.0+ #2 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) ...... RIP: 0010:bpf_map_lookup_elem+0x54/0x60 ...... Call Trace: <TASK> ? __warn+0xa5/0x240 ? bpf_map_lookup_elem+0x54/0x60 ? report_bug+0x1ba/0x1f0 ? handle_bug+0x40/0x80 ? exc_invalid_op+0x18/0x50 ? asm_exc_invalid_op+0x1b/0x20 ? __pfx_bpf_map_lookup_elem+0x10/0x10 ? rcu_lockdep_current_cpu_online+0x65/0xb0 ? rcu_is_watching+0x23/0x50 ? bpf_map_lookup_elem+0x54/0x60 ? __pfx_bpf_map_lookup_elem+0x10/0x10 ___bpf_prog_run+0x513/0x3b70 __bpf_prog_run32+0x9d/0xd0 ? __bpf_prog_enter_sleepable_recur+0xad/0x120 ? __bpf_prog_enter_sleepable_recur+0x3e/0x120 bpf_trampoline_6442580665+0x4d/0x1000 __x64_sys_getpgid+0x5/0x30 ? do_syscall_64+0x36/0xb0 entry_SYSCALL_64_after_hwframe+0x6e/0x76 </TASK>

In the Linux kernel, the following vulnerability has been resolved: fbdev: Fix invalid page access after closing deferred I/O devices When a fbdev with deferred I/O is once opened and closed, the dirty pages still remain queued in the pageref list, and eventually later those may be processed in the delayed work. This may lead to a corruption of pages, hitting an Oops. This patch makes sure to cancel the delayed work and clean up the pageref list at closing the device for addressing the bug. A part of the cleanup code is factored out as a new helper function that is called from the common fb_release().

In the Linux kernel, the following vulnerability has been resolved: net: nfc: llcp: Add lock when modifying device list The device list needs its associated lock held when modifying it, or the list could become corrupted, as syzbot discovered.

In the Linux kernel, the following vulnerability has been resolved: ieee802154: ca8210: Fix a potential UAF in ca8210_probe If of_clk_add_provider() fails in ca8210_register_ext_clock(), it calls clk_unregister() to release priv->clk and returns an error. However, the caller ca8210_probe() then calls ca8210_remove(), where priv->clk is freed again in ca8210_unregister_ext_clock(). In this case, a use-after-free may happen in the second time we call clk_unregister(). Fix this by removing the first clk_unregister(). Also, priv->clk could be an error code on failure of clk_register_fixed_rate(). Use IS_ERR_OR_NULL to catch this case in ca8210_unregister_ext_clock().

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: fix potential key use-after-free When ieee80211_key_link() is called by ieee80211_gtk_rekey_add() but returns 0 due to KRACK protection (identical key reinstall), ieee80211_gtk_rekey_add() will still return a pointer into the key, in a potential use-after-free. This normally doesn't happen since it's only called by iwlwifi in case of WoWLAN rekey offload which has its own KRACK protection, but still better to fix, do that by returning an error code and converting that to success on the cfg80211 boundary only, leaving the error for bad callers of ieee80211_gtk_rekey_add().

In the Linux kernel, the following vulnerability has been resolved: serial: 8250: omap: Don't skip resource freeing if pm_runtime_resume_and_get() failed Returning an error code from .remove() makes the driver core emit the little helpful error message: remove callback returned a non-zero value. This will be ignored. and then remove the device anyhow. So all resources that were not freed are leaked in this case. Skipping serial8250_unregister_port() has the potential to keep enough of the UART around to trigger a use-after-free. So replace the error return (and with it the little helpful error message) by a more useful error message and continue to cleanup.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix a race condition between btf_put() and map_free() When running `./test_progs -j` in my local vm with latest kernel, I once hit a kasan error like below: [ 1887.184724] BUG: KASAN: slab-use-after-free in bpf_rb_root_free+0x1f8/0x2b0 [ 1887.185599] Read of size 4 at addr ffff888106806910 by task kworker/u12:2/2830 [ 1887.186498] [ 1887.186712] CPU: 3 PID: 2830 Comm: kworker/u12:2 Tainted: G OEL 6.7.0-rc3-00699-g90679706d486-dirty #494 [ 1887.188034] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 1887.189618] Workqueue: events_unbound bpf_map_free_deferred [ 1887.190341] Call Trace: [ 1887.190666] <TASK> [ 1887.190949] dump_stack_lvl+0xac/0xe0 [ 1887.191423] ? nf_tcp_handle_invalid+0x1b0/0x1b0 [ 1887.192019] ? panic+0x3c0/0x3c0 [ 1887.192449] print_report+0x14f/0x720 [ 1887.192930] ? preempt_count_sub+0x1c/0xd0 [ 1887.193459] ? __virt_addr_valid+0xac/0x120 [ 1887.194004] ? bpf_rb_root_free+0x1f8/0x2b0 [ 1887.194572] kasan_report+0xc3/0x100 [ 1887.195085] ? bpf_rb_root_free+0x1f8/0x2b0 [ 1887.195668] bpf_rb_root_free+0x1f8/0x2b0 [ 1887.196183] ? __bpf_obj_drop_impl+0xb0/0xb0 [ 1887.196736] ? preempt_count_sub+0x1c/0xd0 [ 1887.197270] ? preempt_count_sub+0x1c/0xd0 [ 1887.197802] ? _raw_spin_unlock+0x1f/0x40 [ 1887.198319] bpf_obj_free_fields+0x1d4/0x260 [ 1887.198883] array_map_free+0x1a3/0x260 [ 1887.199380] bpf_map_free_deferred+0x7b/0xe0 [ 1887.199943] process_scheduled_works+0x3a2/0x6c0 [ 1887.200549] worker_thread+0x633/0x890 [ 1887.201047] ? __kthread_parkme+0xd7/0xf0 [ 1887.201574] ? kthread+0x102/0x1d0 [ 1887.202020] kthread+0x1ab/0x1d0 [ 1887.202447] ? pr_cont_work+0x270/0x270 [ 1887.202954] ? kthread_blkcg+0x50/0x50 [ 1887.203444] ret_from_fork+0x34/0x50 [ 1887.203914] ? kthread_blkcg+0x50/0x50 [ 1887.204397] ret_from_fork_asm+0x11/0x20 [ 1887.204913] </TASK> [ 1887.204913] </TASK> [ 1887.205209] [ 1887.205416] Allocated by task 2197: [ 1887.205881] kasan_set_track+0x3f/0x60 [ 1887.206366] __kasan_kmalloc+0x6e/0x80 [ 1887.206856] __kmalloc+0xac/0x1a0 [ 1887.207293] btf_parse_fields+0xa15/0x1480 [ 1887.207836] btf_parse_struct_metas+0x566/0x670 [ 1887.208387] btf_new_fd+0x294/0x4d0 [ 1887.208851] __sys_bpf+0x4ba/0x600 [ 1887.209292] __x64_sys_bpf+0x41/0x50 [ 1887.209762] do_syscall_64+0x4c/0xf0 [ 1887.210222] entry_SYSCALL_64_after_hwframe+0x63/0x6b [ 1887.210868] [ 1887.211074] Freed by task 36: [ 1887.211460] kasan_set_track+0x3f/0x60 [ 1887.211951] kasan_save_free_info+0x28/0x40 [ 1887.212485] ____kasan_slab_free+0x101/0x180 [ 1887.213027] __kmem_cache_free+0xe4/0x210 [ 1887.213514] btf_free+0x5b/0x130 [ 1887.213918] rcu_core+0x638/0xcc0 [ 1887.214347] __do_softirq+0x114/0x37e The error happens at bpf_rb_root_free+0x1f8/0x2b0: 00000000000034c0 <bpf_rb_root_free>: ; { 34c0: f3 0f 1e fa endbr64 34c4: e8 00 00 00 00 callq 0x34c9 <bpf_rb_root_free+0x9> 34c9: 55 pushq %rbp 34ca: 48 89 e5 movq %rsp, %rbp ... ; if (rec && rec->refcount_off >= 0 && 36aa: 4d 85 ed testq %r13, %r13 36ad: 74 a9 je 0x3658 <bpf_rb_root_free+0x198> 36af: 49 8d 7d 10 leaq 0x10(%r13), %rdi 36b3: e8 00 00 00 00 callq 0x36b8 <bpf_rb_root_free+0x1f8> <==== kasan function 36b8: 45 8b 7d 10 movl 0x10(%r13), %r15d <==== use-after-free load 36bc: 45 85 ff testl %r15d, %r15d 36bf: 78 8c js 0x364d <bpf_rb_root_free+0x18d> So the problem ---truncated---

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Validate data run offset This adds sanity checks for data run offset. We should make sure data run offset is legit before trying to unpack them, otherwise we may encounter use-after-free or some unexpected memory access behaviors. [ 82.940342] BUG: KASAN: use-after-free in run_unpack+0x2e3/0x570 [ 82.941180] Read of size 1 at addr ffff888008a8487f by task mount/240 [ 82.941670] [ 82.942069] CPU: 0 PID: 240 Comm: mount Not tainted 5.19.0+ #15 [ 82.942482] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 82.943720] Call Trace: [ 82.944204] <TASK> [ 82.944471] dump_stack_lvl+0x49/0x63 [ 82.944908] print_report.cold+0xf5/0x67b [ 82.945141] ? __wait_on_bit+0x106/0x120 [ 82.945750] ? run_unpack+0x2e3/0x570 [ 82.946626] kasan_report+0xa7/0x120 [ 82.947046] ? run_unpack+0x2e3/0x570 [ 82.947280] __asan_load1+0x51/0x60 [ 82.947483] run_unpack+0x2e3/0x570 [ 82.947709] ? memcpy+0x4e/0x70 [ 82.947927] ? run_pack+0x7a0/0x7a0 [ 82.948158] run_unpack_ex+0xad/0x3f0 [ 82.948399] ? mi_enum_attr+0x14a/0x200 [ 82.948717] ? run_unpack+0x570/0x570 [ 82.949072] ? ni_enum_attr_ex+0x1b2/0x1c0 [ 82.949332] ? ni_fname_type.part.0+0xd0/0xd0 [ 82.949611] ? mi_read+0x262/0x2c0 [ 82.949970] ? ntfs_cmp_names_cpu+0x125/0x180 [ 82.950249] ntfs_iget5+0x632/0x1870 [ 82.950621] ? ntfs_get_block_bmap+0x70/0x70 [ 82.951192] ? evict+0x223/0x280 [ 82.951525] ? iput.part.0+0x286/0x320 [ 82.951969] ntfs_fill_super+0x1321/0x1e20 [ 82.952436] ? put_ntfs+0x1d0/0x1d0 [ 82.952822] ? vsprintf+0x20/0x20 [ 82.953188] ? mutex_unlock+0x81/0xd0 [ 82.953379] ? set_blocksize+0x95/0x150 [ 82.954001] get_tree_bdev+0x232/0x370 [ 82.954438] ? put_ntfs+0x1d0/0x1d0 [ 82.954700] ntfs_fs_get_tree+0x15/0x20 [ 82.955049] vfs_get_tree+0x4c/0x130 [ 82.955292] path_mount+0x645/0xfd0 [ 82.955615] ? putname+0x80/0xa0 [ 82.955955] ? finish_automount+0x2e0/0x2e0 [ 82.956310] ? kmem_cache_free+0x110/0x390 [ 82.956723] ? putname+0x80/0xa0 [ 82.957023] do_mount+0xd6/0xf0 [ 82.957411] ? path_mount+0xfd0/0xfd0 [ 82.957638] ? __kasan_check_write+0x14/0x20 [ 82.957948] __x64_sys_mount+0xca/0x110 [ 82.958310] do_syscall_64+0x3b/0x90 [ 82.958719] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 82.959341] RIP: 0033:0x7fd0d1ce948a [ 82.960193] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008 [ 82.961532] RSP: 002b:00007ffe59ff69a8 EFLAGS: 00000202 ORIG_RAX: 00000000000000a5 [ 82.962527] RAX: ffffffffffffffda RBX: 0000564dcc107060 RCX: 00007fd0d1ce948a [ 82.963266] RDX: 0000564dcc107260 RSI: 0000564dcc1072e0 RDI: 0000564dcc10fce0 [ 82.963686] RBP: 0000000000000000 R08: 0000564dcc107280 R09: 0000000000000020 [ 82.964272] R10: 00000000c0ed0000 R11: 0000000000000202 R12: 0000564dcc10fce0 [ 82.964785] R13: 0000564dcc107260 R14: 0000000000000000 R15: 00000000ffffffff

In the Linux kernel, the following vulnerability has been resolved: hwmon: (adc128d818) Fix underflows seen when writing limit attributes DIV_ROUND_CLOSEST() after kstrtol() results in an underflow if a large negative number such as -9223372036854775808 is provided by the user. Fix it by reordering clamp_val() and DIV_ROUND_CLOSEST() operations.

A flaw null pointer dereference in the Linux kernel cgroupv2 subsystem in versions before 5.7.10 was found in the way when reboot the system. A local user could use this flaw to crash the system or escalate their privileges on the system.

In the Linux kernel, the following vulnerability has been resolved: staging: media: atomisp: Fix stack buffer overflow in gmin_get_var_int() When gmin_get_config_var() calls efi.get_variable() and the EFI variable is larger than the expected buffer size, two behaviors combine to create a stack buffer overflow: 1. gmin_get_config_var() does not return the proper error code when efi.get_variable() fails. It returns the stale 'ret' value from earlier operations instead of indicating the EFI failure. 2. When efi.get_variable() returns EFI_BUFFER_TOO_SMALL, it updates *out_len to the required buffer size but writes no data to the output buffer. However, due to bug #1, gmin_get_var_int() believes the call succeeded. The caller gmin_get_var_int() then performs: - Allocates val[CFG_VAR_NAME_MAX + 1] (65 bytes) on stack - Calls gmin_get_config_var(dev, is_gmin, var, val, &len) with len=64 - If EFI variable is >64 bytes, efi.get_variable() sets len=required_size - Due to bug #1, thinks call succeeded with len=required_size - Executes val[len] = 0, writing past end of 65-byte stack buffer This creates a stack buffer overflow when EFI variables are larger than 64 bytes. Since EFI variables can be controlled by firmware or system configuration, this could potentially be exploited for code execution. Fix the bug by returning proper error codes from gmin_get_config_var() based on EFI status instead of stale 'ret' value. The gmin_get_var_int() function is called during device initialization for camera sensor configuration on Intel Bay Trail and Cherry Trail platforms using the atomisp camera stack.

In the Linux kernel, the following vulnerability has been resolved: fbcon: fix integer overflow in fbcon_do_set_font Fix integer overflow vulnerabilities in fbcon_do_set_font() where font size calculations could overflow when handling user-controlled font parameters. The vulnerabilities occur when: 1. CALC_FONTSZ(h, pitch, charcount) performs h * pith * charcount multiplication with user-controlled values that can overflow. 2. FONT_EXTRA_WORDS * sizeof(int) + size addition can also overflow 3. This results in smaller allocations than expected, leading to buffer overflows during font data copying. Add explicit overflow checking using check_mul_overflow() and check_add_overflow() kernel helpers to safety validate all size calculations before allocation.