In the Linux kernel, the following vulnerability has been resolved: ice: fix NULL access of tx->in_use in ice_ptp_ts_irq The E810 device has support for a "low latency" firmware interface to access and read the Tx timestamps. This interface does not use the standard Tx timestamp logic, due to the latency overhead of proxying sideband command requests over the firmware AdminQ. The logic still makes use of the Tx timestamp tracking structure, ice_ptp_tx, as it uses the same "ready" bitmap to track which Tx timestamps complete. Unfortunately, the ice_ptp_ts_irq() function does not check if the tracker is initialized before its first access. This results in NULL dereference or use-after-free bugs similar to the following: [245977.278756] BUG: kernel NULL pointer dereference, address: 0000000000000000 [245977.278774] RIP: 0010:_find_first_bit+0x19/0x40 [245977.278796] Call Trace: [245977.278809] ? ice_misc_intr+0x364/0x380 [ice] This can occur if a Tx timestamp interrupt races with the driver reset logic. Fix this by only checking the in_use bitmap (and other fields) if the tracker is marked as initialized. The reset flow will clear the init field under lock before it tears the tracker down, thus preventing any use-after-free or NULL access.

In the Linux kernel, the following vulnerability has been resolved: iio: backend: fix out-of-bound write The buffer is set to 80 character. If a caller write more characters, count is truncated to the max available space in "simple_write_to_buffer". But afterwards a string terminator is written to the buffer at offset count without boundary check. The zero termination is written OUT-OF-BOUND. Add a check that the given buffer is smaller then the buffer to prevent.

In the Linux kernel, the following vulnerability has been resolved: ASoC: mediatek: mt8365-dai-i2s: pass correct size to mt8365_dai_set_priv Given mt8365_dai_set_priv allocate priv_size space to copy priv_data which means we should pass mt8365_i2s_priv[i] or "struct mtk_afe_i2s_priv" instead of afe_priv which has the size of "struct mt8365_afe_private". Otherwise the KASAN complains about. [ 59.389765] BUG: KASAN: global-out-of-bounds in mt8365_dai_set_priv+0xc8/0x168 [snd_soc_mt8365_pcm] ... [ 59.394789] Call trace: [ 59.395167] dump_backtrace+0xa0/0x128 [ 59.395733] show_stack+0x20/0x38 [ 59.396238] dump_stack_lvl+0xe8/0x148 [ 59.396806] print_report+0x37c/0x5e0 [ 59.397358] kasan_report+0xac/0xf8 [ 59.397885] kasan_check_range+0xe8/0x190 [ 59.398485] asan_memcpy+0x3c/0x98 [ 59.399022] mt8365_dai_set_priv+0xc8/0x168 [snd_soc_mt8365_pcm] [ 59.399928] mt8365_dai_i2s_register+0x1e8/0x2b0 [snd_soc_mt8365_pcm] [ 59.400893] mt8365_afe_pcm_dev_probe+0x4d0/0xdf0 [snd_soc_mt8365_pcm] [ 59.401873] platform_probe+0xcc/0x228 [ 59.402442] really_probe+0x340/0x9e8 [ 59.402992] driver_probe_device+0x16c/0x3f8 [ 59.403638] driver_probe_device+0x64/0x1d8 [ 59.404256] driver_attach+0x1dc/0x4c8 [ 59.404840] bus_for_each_dev+0x100/0x190 [ 59.405442] driver_attach+0x44/0x68 [ 59.405980] bus_add_driver+0x23c/0x500 [ 59.406550] driver_register+0xf8/0x3d0 [ 59.407122] platform_driver_register+0x68/0x98 [ 59.407810] mt8365_afe_pcm_driver_init+0x2c/0xff8 [snd_soc_mt8365_pcm]

In the Linux kernel, the following vulnerability has been resolved: ipmi:msghandler: Fix potential memory corruption in ipmi_create_user() The "intf" list iterator is an invalid pointer if the correct "intf->intf_num" is not found. Calling atomic_dec(&intf->nr_users) on and invalid pointer will lead to memory corruption. We don't really need to call atomic_dec() if we haven't called atomic_add_return() so update the if (intf->in_shutdown) path as well.

In the Linux kernel, the following vulnerability has been resolved: fbdev: Fix vmalloc out-of-bounds write in fast_imageblit This issue triggers when a userspace program does an ioctl FBIOPUT_CON2FBMAP by passing console number and frame buffer number. Ideally this maps console to frame buffer and updates the screen if console is visible. As part of mapping it has to do resize of console according to frame buffer info. if this resize fails and returns from vc_do_resize() and continues further. At this point console and new frame buffer are mapped and sets display vars. Despite failure still it continue to proceed updating the screen at later stages where vc_data is related to previous frame buffer and frame buffer info and display vars are mapped to new frame buffer and eventully leading to out-of-bounds write in fast_imageblit(). This bheviour is excepted only when fg_console is equal to requested console which is a visible console and updates screen with invalid struct references in fbcon_putcs().

In the Linux kernel, the following vulnerability has been resolved: proc: use the same treatment to check proc_lseek as ones for proc_read_iter et.al Check pde->proc_ops->proc_lseek directly may cause UAF in rmmod scenario. It's a gap in proc_reg_open() after commit 654b33ada4ab("proc: fix UAF in proc_get_inode()"). Followed by AI Viro's suggestion, fix it in same manner.

In the Linux kernel, the following vulnerability has been resolved: media: ivsc: Fix crash at shutdown due to missing mei_cldev_disable() calls Both the ACE and CSI driver are missing a mei_cldev_disable() call in their remove() function. This causes the mei_cl client to stay part of the mei_device->file_list list even though its memory is freed by mei_cl_bus_dev_release() calling kfree(cldev->cl). This leads to a use-after-free when mei_vsc_remove() runs mei_stop() which first removes all mei bus devices calling mei_ace_remove() and mei_csi_remove() followed by mei_cl_bus_dev_release() and then calls mei_cl_all_disconnect() which walks over mei_device->file_list dereferecing the just freed cldev->cl. And mei_vsc_remove() it self is run at shutdown because of the platform_device_unregister(tp->pdev) in vsc_tp_shutdown() When building a kernel with KASAN this leads to the following KASAN report: [ 106.634504] ================================================================== [ 106.634623] BUG: KASAN: slab-use-after-free in mei_cl_set_disconnected (drivers/misc/mei/client.c:783) mei [ 106.634683] Read of size 4 at addr ffff88819cb62018 by task systemd-shutdow/1 [ 106.634729] [ 106.634767] Tainted: [E]=UNSIGNED_MODULE [ 106.634770] Hardware name: Dell Inc. XPS 16 9640/09CK4V, BIOS 1.12.0 02/10/2025 [ 106.634773] Call Trace: [ 106.634777] <TASK> ... [ 106.634871] kasan_report (mm/kasan/report.c:221 mm/kasan/report.c:636) [ 106.634901] mei_cl_set_disconnected (drivers/misc/mei/client.c:783) mei [ 106.634921] mei_cl_all_disconnect (drivers/misc/mei/client.c:2165 (discriminator 4)) mei [ 106.634941] mei_reset (drivers/misc/mei/init.c:163) mei ... [ 106.635042] mei_stop (drivers/misc/mei/init.c:348) mei [ 106.635062] mei_vsc_remove (drivers/misc/mei/mei_dev.h:784 drivers/misc/mei/platform-vsc.c:393) mei_vsc [ 106.635066] platform_remove (drivers/base/platform.c:1424) Add the missing mei_cldev_disable() calls so that the mei_cl gets removed from mei_device->file_list before it is freed to fix this.

In the Linux kernel, the following vulnerability has been resolved: fs: writeback: fix use-after-free in __mark_inode_dirty() An use-after-free issue occurred when __mark_inode_dirty() get the bdi_writeback that was in the progress of switching. CPU: 1 PID: 562 Comm: systemd-random- Not tainted 6.6.56-gb4403bd46a8e #1 ...... pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __mark_inode_dirty+0x124/0x418 lr : __mark_inode_dirty+0x118/0x418 sp : ffffffc08c9dbbc0 ........ Call trace: __mark_inode_dirty+0x124/0x418 generic_update_time+0x4c/0x60 file_modified+0xcc/0xd0 ext4_buffered_write_iter+0x58/0x124 ext4_file_write_iter+0x54/0x704 vfs_write+0x1c0/0x308 ksys_write+0x74/0x10c __arm64_sys_write+0x1c/0x28 invoke_syscall+0x48/0x114 el0_svc_common.constprop.0+0xc0/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x40/0xe4 el0t_64_sync_handler+0x120/0x12c el0t_64_sync+0x194/0x198 Root cause is: systemd-random-seed kworker ---------------------------------------------------------------------- ___mark_inode_dirty inode_switch_wbs_work_fn spin_lock(&inode->i_lock); inode_attach_wb locked_inode_to_wb_and_lock_list get inode->i_wb spin_unlock(&inode->i_lock); spin_lock(&wb->list_lock) spin_lock(&inode->i_lock) inode_io_list_move_locked spin_unlock(&wb->list_lock) spin_unlock(&inode->i_lock) spin_lock(&old_wb->list_lock) inode_do_switch_wbs spin_lock(&inode->i_lock) inode->i_wb = new_wb spin_unlock(&inode->i_lock) spin_unlock(&old_wb->list_lock) wb_put_many(old_wb, nr_switched) cgwb_release old wb released wb_wakeup_delayed() accesses wb, then trigger the use-after-free issue Fix this race condition by holding inode spinlock until wb_wakeup_delayed() finished.

In the Linux kernel, the following vulnerability has been resolved: drm/xe: Fix vm_bind_ioctl double free bug If the argument check during an array bind fails, the bind_ops are freed twice as seen below. Fix this by setting bind_ops to NULL after freeing. ================================================================== BUG: KASAN: double-free in xe_vm_bind_ioctl+0x1b2/0x21f0 [xe] Free of addr ffff88813bb9b800 by task xe_vm/14198 CPU: 5 UID: 0 PID: 14198 Comm: xe_vm Not tainted 6.16.0-xe-eudebug-cmanszew+ #520 PREEMPT(full) Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-P DDR5 RVP, BIOS ADLPFWI1.R00.2411.A02.2110081023 10/08/2021 Call Trace: <TASK> dump_stack_lvl+0x82/0xd0 print_report+0xcb/0x610 ? __virt_addr_valid+0x19a/0x300 ? xe_vm_bind_ioctl+0x1b2/0x21f0 [xe] kasan_report_invalid_free+0xc8/0xf0 ? xe_vm_bind_ioctl+0x1b2/0x21f0 [xe] ? xe_vm_bind_ioctl+0x1b2/0x21f0 [xe] check_slab_allocation+0x102/0x130 kfree+0x10d/0x440 ? should_fail_ex+0x57/0x2f0 ? xe_vm_bind_ioctl+0x1b2/0x21f0 [xe] xe_vm_bind_ioctl+0x1b2/0x21f0 [xe] ? __pfx_xe_vm_bind_ioctl+0x10/0x10 [xe] ? __lock_acquire+0xab9/0x27f0 ? lock_acquire+0x165/0x300 ? drm_dev_enter+0x53/0xe0 [drm] ? find_held_lock+0x2b/0x80 ? drm_dev_exit+0x30/0x50 [drm] ? drm_ioctl_kernel+0x128/0x1c0 [drm] drm_ioctl_kernel+0x128/0x1c0 [drm] ? __pfx_xe_vm_bind_ioctl+0x10/0x10 [xe] ? find_held_lock+0x2b/0x80 ? __pfx_drm_ioctl_kernel+0x10/0x10 [drm] ? should_fail_ex+0x57/0x2f0 ? __pfx_xe_vm_bind_ioctl+0x10/0x10 [xe] drm_ioctl+0x352/0x620 [drm] ? __pfx_drm_ioctl+0x10/0x10 [drm] ? __pfx_rpm_resume+0x10/0x10 ? do_raw_spin_lock+0x11a/0x1b0 ? find_held_lock+0x2b/0x80 ? __pm_runtime_resume+0x61/0xc0 ? rcu_is_watching+0x20/0x50 ? trace_irq_enable.constprop.0+0xac/0xe0 xe_drm_ioctl+0x91/0xc0 [xe] __x64_sys_ioctl+0xb2/0x100 ? rcu_is_watching+0x20/0x50 do_syscall_64+0x68/0x2e0 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7fa9acb24ded (cherry picked from commit a01b704527c28a2fd43a17a85f8996b75ec8492a)

In the Linux kernel, the following vulnerability has been resolved: atm: atmtcp: Prevent arbitrary write in atmtcp_recv_control(). syzbot reported the splat below. [0] When atmtcp_v_open() or atmtcp_v_close() is called via connect() or close(), atmtcp_send_control() is called to send an in-kernel special message. The message has ATMTCP_HDR_MAGIC in atmtcp_control.hdr.length. Also, a pointer of struct atm_vcc is set to atmtcp_control.vcc. The notable thing is struct atmtcp_control is uAPI but has a space for an in-kernel pointer. struct atmtcp_control { struct atmtcp_hdr hdr; /* must be first */ ... atm_kptr_t vcc; /* both directions */ ... } __ATM_API_ALIGN; typedef struct { unsigned char _[8]; } __ATM_API_ALIGN atm_kptr_t; The special message is processed in atmtcp_recv_control() called from atmtcp_c_send(). atmtcp_c_send() is vcc->dev->ops->send() and called from 2 paths: 1. .ndo_start_xmit() (vcc->send() == atm_send_aal0()) 2. vcc_sendmsg() The problem is sendmsg() does not validate the message length and userspace can abuse atmtcp_recv_control() to overwrite any kptr by atmtcp_control. Let's add a new ->pre_send() hook to validate messages from sendmsg(). [0]: Oops: general protection fault, probably for non-canonical address 0xdffffc00200000ab: 0000 [#1] SMP KASAN PTI KASAN: probably user-memory-access in range [0x0000000100000558-0x000000010000055f] CPU: 0 UID: 0 PID: 5865 Comm: syz-executor331 Not tainted 6.17.0-rc1-syzkaller-00215-gbab3ce404553 #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/12/2025 RIP: 0010:atmtcp_recv_control drivers/atm/atmtcp.c:93 [inline] RIP: 0010:atmtcp_c_send+0x1da/0x950 drivers/atm/atmtcp.c:297 Code: 4d 8d 75 1a 4c 89 f0 48 c1 e8 03 42 0f b6 04 20 84 c0 0f 85 15 06 00 00 41 0f b7 1e 4d 8d b7 60 05 00 00 4c 89 f0 48 c1 e8 03 <42> 0f b6 04 20 84 c0 0f 85 13 06 00 00 66 41 89 1e 4d 8d 75 1c 4c RSP: 0018:ffffc90003f5f810 EFLAGS: 00010203 RAX: 00000000200000ab RBX: 0000000000000000 RCX: 0000000000000000 RDX: ffff88802a510000 RSI: 00000000ffffffff RDI: ffff888030a6068c RBP: ffff88802699fb40 R08: ffff888030a606eb R09: 1ffff1100614c0dd R10: dffffc0000000000 R11: ffffffff8718fc40 R12: dffffc0000000000 R13: ffff888030a60680 R14: 000000010000055f R15: 00000000ffffffff FS: 00007f8d7e9236c0(0000) GS:ffff888125c1c000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000045ad50 CR3: 0000000075bde000 CR4: 00000000003526f0 Call Trace: <TASK> vcc_sendmsg+0xa10/0xc60 net/atm/common.c:645 sock_sendmsg_nosec net/socket.c:714 [inline] __sock_sendmsg+0x219/0x270 net/socket.c:729 ____sys_sendmsg+0x505/0x830 net/socket.c:2614 ___sys_sendmsg+0x21f/0x2a0 net/socket.c:2668 __sys_sendmsg net/socket.c:2700 [inline] __do_sys_sendmsg net/socket.c:2705 [inline] __se_sys_sendmsg net/socket.c:2703 [inline] __x64_sys_sendmsg+0x19b/0x260 net/socket.c:2703 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f8d7e96a4a9 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 51 18 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f8d7e923198 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f8d7e9f4308 RCX: 00007f8d7e96a4a9 RDX: 0000000000000000 RSI: 0000200000000240 RDI: 0000000000000005 RBP: 00007f8d7e9f4300 R08: 65732f636f72702f R09: 65732f636f72702f R10: 65732f636f72702f R11: 0000000000000246 R12: 00007f8d7e9c10ac R13: 00007f8d7e9231a0 R14: 0000200000000200 R15: 0000200000000250 </TASK> Modules linked in:

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix use-after-free in crypt_message when using async crypto The CVE-2024-50047 fix removed asynchronous crypto handling from crypt_message(), assuming all crypto operations are synchronous. However, when hardware crypto accelerators are used, this can cause use-after-free crashes: crypt_message() // Allocate the creq buffer containing the req creq = smb2_get_aead_req(..., &req); // Async encryption returns -EINPROGRESS immediately rc = enc ? crypto_aead_encrypt(req) : crypto_aead_decrypt(req); // Free creq while async operation is still in progress kvfree_sensitive(creq, ...); Hardware crypto modules often implement async AEAD operations for performance. When crypto_aead_encrypt/decrypt() returns -EINPROGRESS, the operation completes asynchronously. Without crypto_wait_req(), the function immediately frees the request buffer, leading to crashes when the driver later accesses the freed memory. This results in a use-after-free condition when the hardware crypto driver later accesses the freed request structure, leading to kernel crashes with NULL pointer dereferences. The issue occurs because crypto_alloc_aead() with mask=0 doesn't guarantee synchronous operation. Even without CRYPTO_ALG_ASYNC in the mask, async implementations can be selected. Fix by restoring the async crypto handling: - DECLARE_CRYPTO_WAIT(wait) for completion tracking - aead_request_set_callback() for async completion notification - crypto_wait_req() to wait for operation completion This ensures the request buffer isn't freed until the crypto operation completes, whether synchronous or asynchronous, while preserving the CVE-2024-50047 fix.

In the Linux kernel, the following vulnerability has been resolved: kernfs: Fix UAF in polling when open file is released A use-after-free (UAF) vulnerability was identified in the PSI (Pressure Stall Information) monitoring mechanism: BUG: KASAN: slab-use-after-free in psi_trigger_poll+0x3c/0x140 Read of size 8 at addr ffff3de3d50bd308 by task systemd/1 psi_trigger_poll+0x3c/0x140 cgroup_pressure_poll+0x70/0xa0 cgroup_file_poll+0x8c/0x100 kernfs_fop_poll+0x11c/0x1c0 ep_item_poll.isra.0+0x188/0x2c0 Allocated by task 1: cgroup_file_open+0x88/0x388 kernfs_fop_open+0x73c/0xaf0 do_dentry_open+0x5fc/0x1200 vfs_open+0xa0/0x3f0 do_open+0x7e8/0xd08 path_openat+0x2fc/0x6b0 do_filp_open+0x174/0x368 Freed by task 8462: cgroup_file_release+0x130/0x1f8 kernfs_drain_open_files+0x17c/0x440 kernfs_drain+0x2dc/0x360 kernfs_show+0x1b8/0x288 cgroup_file_show+0x150/0x268 cgroup_pressure_write+0x1dc/0x340 cgroup_file_write+0x274/0x548 Reproduction Steps: 1. Open test/cpu.pressure and establish epoll monitoring 2. Disable monitoring: echo 0 > test/cgroup.pressure 3. Re-enable monitoring: echo 1 > test/cgroup.pressure The race condition occurs because: 1. When cgroup.pressure is disabled (echo 0 > cgroup.pressure), it: - Releases PSI triggers via cgroup_file_release() - Frees of->priv through kernfs_drain_open_files() 2. While epoll still holds reference to the file and continues polling 3. Re-enabling (echo 1 > cgroup.pressure) accesses freed of->priv epolling disable/enable cgroup.pressure fd=open(cpu.pressure) while(1) ... epoll_wait kernfs_fop_poll kernfs_get_active = true echo 0 > cgroup.pressure ... cgroup_file_show kernfs_show // inactive kn kernfs_drain_open_files cft->release(of); kfree(ctx); ... kernfs_get_active = false echo 1 > cgroup.pressure kernfs_show kernfs_activate_one(kn); kernfs_fop_poll kernfs_get_active = true cgroup_file_poll psi_trigger_poll // UAF ... end: close(fd) To address this issue, introduce kernfs_get_active_of() for kernfs open files to obtain active references. This function will fail if the open file has been released. Replace kernfs_get_active() with kernfs_get_active_of() to prevent further operations on released file descriptors.

In the Linux kernel, the following vulnerability has been resolved: PCI: endpoint: Fix configfs group list head handling Doing a list_del() on the epf_group field of struct pci_epf_driver in pci_epf_remove_cfs() is not correct as this field is a list head, not a list entry. This list_del() call triggers a KASAN warning when an endpoint function driver which has a configfs attribute group is torn down: ================================================================== BUG: KASAN: slab-use-after-free in pci_epf_remove_cfs+0x17c/0x198 Write of size 8 at addr ffff00010f4a0d80 by task rmmod/319 CPU: 3 UID: 0 PID: 319 Comm: rmmod Not tainted 6.16.0-rc2 #1 NONE Hardware name: Radxa ROCK 5B (DT) Call trace: show_stack+0x2c/0x84 (C) dump_stack_lvl+0x70/0x98 print_report+0x17c/0x538 kasan_report+0xb8/0x190 __asan_report_store8_noabort+0x20/0x2c pci_epf_remove_cfs+0x17c/0x198 pci_epf_unregister_driver+0x18/0x30 nvmet_pci_epf_cleanup_module+0x24/0x30 [nvmet_pci_epf] __arm64_sys_delete_module+0x264/0x424 invoke_syscall+0x70/0x260 el0_svc_common.constprop.0+0xac/0x230 do_el0_svc+0x40/0x58 el0_svc+0x48/0xdc el0t_64_sync_handler+0x10c/0x138 el0t_64_sync+0x198/0x19c ... Remove this incorrect list_del() call from pci_epf_remove_cfs().

In the Linux kernel, the following vulnerability has been resolved: dmaengine: idxd: Fix double free in idxd_setup_wqs() The clean up in idxd_setup_wqs() has had a couple bugs because the error handling is a bit subtle. It's simpler to just re-write it in a cleaner way. The issues here are: 1) If "idxd->max_wqs" is <= 0 then we call put_device(conf_dev) when "conf_dev" hasn't been initialized. 2) If kzalloc_node() fails then again "conf_dev" is invalid. It's either uninitialized or it points to the "conf_dev" from the previous iteration so it leads to a double free. It's better to free partial loop iterations within the loop and then the unwinding at the end can handle whole loop iterations. I also renamed the labels to describe what the goto does and not where the goto was located.

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Fix UAF on sva unbind with pending IOPFs Commit 17fce9d2336d ("iommu/vt-d: Put iopf enablement in domain attach path") disables IOPF on device by removing the device from its IOMMU's IOPF queue when the last IOPF-capable domain is detached from the device. Unfortunately, it did this in a wrong place where there are still pending IOPFs. As a result, a use-after-free error is potentially triggered and eventually a kernel panic with a kernel trace similar to the following: refcount_t: underflow; use-after-free. WARNING: CPU: 3 PID: 313 at lib/refcount.c:28 refcount_warn_saturate+0xd8/0xe0 Workqueue: iopf_queue/dmar0-iopfq iommu_sva_handle_iopf Call Trace: <TASK> iopf_free_group+0xe/0x20 process_one_work+0x197/0x3d0 worker_thread+0x23a/0x350 ? rescuer_thread+0x4a0/0x4a0 kthread+0xf8/0x230 ? finish_task_switch.isra.0+0x81/0x260 ? kthreads_online_cpu+0x110/0x110 ? kthreads_online_cpu+0x110/0x110 ret_from_fork+0x13b/0x170 ? kthreads_online_cpu+0x110/0x110 ret_from_fork_asm+0x11/0x20 </TASK> ---[ end trace 0000000000000000 ]--- The intel_pasid_tear_down_entry() function is responsible for blocking hardware from generating new page faults and flushing all in-flight ones. Therefore, moving iopf_for_domain_remove() after this function should resolve this.

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: fix potential OF node use-after-free The for_each_child_of_node() helper drops the reference it takes to each node as it iterates over children and an explicit of_node_put() is only needed when exiting the loop early. Drop the recently introduced bogus additional reference count decrement at each iteration that could potentially lead to a use-after-free.

In the Linux kernel, the following vulnerability has been resolved: phy: tegra: xusb: Fix unbalanced regulator disable in UTMI PHY mode When transitioning from USB_ROLE_DEVICE to USB_ROLE_NONE, the code assumed that the regulator should be disabled. However, if the regulator is marked as always-on, regulator_is_enabled() continues to return true, leading to an incorrect attempt to disable a regulator which is not enabled. This can result in warnings such as: [ 250.155624] WARNING: CPU: 1 PID: 7326 at drivers/regulator/core.c:3004 _regulator_disable+0xe4/0x1a0 [ 250.155652] unbalanced disables for VIN_SYS_5V0 To fix this, we move the regulator control logic into tegra186_xusb_padctl_id_override() function since it's directly related to the ID override state. The regulator is now only disabled when the role transitions from USB_ROLE_HOST to USB_ROLE_NONE, by checking the VBUS_ID register. This ensures that regulator enable/disable operations are properly balanced and only occur when actually transitioning to/from host mode.

In the Linux kernel, the following vulnerability has been resolved: wifi: wilc1000: avoid buffer overflow in WID string configuration Fix the following copy overflow warning identified by Smatch checker. drivers/net/wireless/microchip/wilc1000/wlan_cfg.c:184 wilc_wlan_parse_response_frame() error: '__memcpy()' 'cfg->s[i]->str' copy overflow (512 vs 65537) This patch introduces size check before accessing the memory buffer. The checks are base on the WID type of received data from the firmware. For WID string configuration, the size limit is determined by individual element size in 'struct wilc_cfg_str_vals' that is maintained in 'len' field of 'struct wilc_cfg_str'.

curl 7.20.0 through 7.70.0 is vulnerable to improper restriction of names for files and other resources that can lead too overwriting a local file when the -J flag is used.

In the Linux kernel, the following vulnerability has been resolved: iommufd: Prevent ALIGN() overflow When allocating IOVA the candidate range gets aligned to the target alignment. If the range is close to ULONG_MAX then the ALIGN() can wrap resulting in a corrupted iova. Open code the ALIGN() using get_add_overflow() to prevent this. This simplifies the checks as we don't need to check for length earlier either. Consolidate the two copies of this code under a single helper. This bug would allow userspace to create a mapping that overlaps with some other mapping or a reserved range.

In the Linux kernel, the following vulnerability has been resolved: nfsd: handle get_client_locked() failure in nfsd4_setclientid_confirm() Lei Lu recently reported that nfsd4_setclientid_confirm() did not check the return value from get_client_locked(). a SETCLIENTID_CONFIRM could race with a confirmed client expiring and fail to get a reference. That could later lead to a UAF. Fix this by getting a reference early in the case where there is an extant confirmed client. If that fails then treat it as if there were no confirmed client found at all. In the case where the unconfirmed client is expiring, just fail and return the result from get_client_locked().

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: use array_index_nospec with indices that come from guest min and dest_id are guest-controlled indices. Using array_index_nospec() after the bounds checks clamps these values to mitigate speculative execution side-channels.

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: Fix error code in iwl_op_mode_dvm_start() Preserve the error code if iwl_setup_deferred_work() fails. The current code returns ERR_PTR(0) (which is NULL) on this path. I believe the missing error code potentially leads to a use after free involving debugfs.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix inode use after free in ext4_end_io_rsv_work() In ext4_io_end_defer_completion(), check if io_end->list_vec is empty to avoid adding an io_end that requires no conversion to the i_rsv_conversion_list, which in turn prevents starting an unnecessary worker. An ext4_emergency_state() check is also added to avoid attempting to abort the journal in an emergency state. Additionally, ext4_put_io_end_defer() is refactored to call ext4_io_end_defer_completion() directly instead of being open-coded. This also prevents starting an unnecessary worker when EXT4_IO_END_FAILED is set but data_err=abort is not enabled. This ensures that the check in ext4_put_io_end_defer() is consistent with the check in ext4_end_bio(). Otherwise, we might add an io_end to the i_rsv_conversion_list and then call ext4_finish_bio(), after which the inode could be freed before ext4_end_io_rsv_work() is called, triggering a use-after-free issue.

In the Linux kernel, the following vulnerability has been resolved: gpiolib: acpi: initialize acpi_gpio_info struct Since commit 7c010d463372 ("gpiolib: acpi: Make sure we fill struct acpi_gpio_info"), uninitialized acpi_gpio_info struct are passed to __acpi_find_gpio() and later in the call stack info->quirks is used in acpi_populate_gpio_lookup. This breaks the i2c_hid_cpi driver: [ 58.122916] i2c_hid_acpi i2c-UNIW0001:00: HID over i2c has not been provided an Int IRQ [ 58.123097] i2c_hid_acpi i2c-UNIW0001:00: probe with driver i2c_hid_acpi failed with error -22 Fix this by initializing the acpi_gpio_info pass to __acpi_find_gpio()

In the Linux kernel, the following vulnerability has been resolved: comedi: Make insn_rw_emulate_bits() do insn->n samples The `insn_rw_emulate_bits()` function is used as a default handler for `INSN_READ` instructions for subdevices that have a handler for `INSN_BITS` but not for `INSN_READ`. Similarly, it is used as a default handler for `INSN_WRITE` instructions for subdevices that have a handler for `INSN_BITS` but not for `INSN_WRITE`. It works by emulating the `INSN_READ` or `INSN_WRITE` instruction handling with a constructed `INSN_BITS` instruction. However, `INSN_READ` and `INSN_WRITE` instructions are supposed to be able read or write multiple samples, indicated by the `insn->n` value, but `insn_rw_emulate_bits()` currently only handles a single sample. For `INSN_READ`, the comedi core will copy `insn->n` samples back to user-space. (That triggered KASAN kernel-infoleak errors when `insn->n` was greater than 1, but that is being fixed more generally elsewhere in the comedi core.) Make `insn_rw_emulate_bits()` either handle `insn->n` samples, or return an error, to conform to the general expectation for `INSN_READ` and `INSN_WRITE` handlers.

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: exynos: Fix programming of HCI_UTRL_NEXUS_TYPE On Google gs101, the number of UTP transfer request slots (nutrs) is 32, and in this case the driver ends up programming the UTRL_NEXUS_TYPE incorrectly as 0. This is because the left hand side of the shift is 1, which is of type int, i.e. 31 bits wide. Shifting by more than that width results in undefined behaviour. Fix this by switching to the BIT() macro, which applies correct type casting as required. This ensures the correct value is written to UTRL_NEXUS_TYPE (0xffffffff on gs101), and it also fixes a UBSAN shift warning: UBSAN: shift-out-of-bounds in drivers/ufs/host/ufs-exynos.c:1113:21 shift exponent 32 is too large for 32-bit type 'int' For consistency, apply the same change to the nutmrs / UTMRL_NEXUS_TYPE write.

In the Linux kernel, the following vulnerability has been resolved: padata: Fix pd UAF once and for all There is a race condition/UAF in padata_reorder that goes back to the initial commit. A reference count is taken at the start of the process in padata_do_parallel, and released at the end in padata_serial_worker. This reference count is (and only is) required for padata_replace to function correctly. If padata_replace is never called then there is no issue. In the function padata_reorder which serves as the core of padata, as soon as padata is added to queue->serial.list, and the associated spin lock released, that padata may be processed and the reference count on pd would go away. Fix this by getting the next padata before the squeue->serial lock is released. In order to make this possible, simplify padata_reorder by only calling it once the next padata arrives.

In the Linux kernel, the following vulnerability has been resolved: dmaengine: fsl-edma: free irq correctly in remove path Add fsl_edma->txirq/errirq check to avoid below warning because no errirq at i.MX9 platform. Otherwise there will be kernel dump: WARNING: CPU: 0 PID: 11 at kernel/irq/devres.c:144 devm_free_irq+0x74/0x80 Modules linked in: CPU: 0 UID: 0 PID: 11 Comm: kworker/u8:0 Not tainted 6.12.0-rc7#18 Hardware name: NXP i.MX93 11X11 EVK board (DT) Workqueue: events_unbound deferred_probe_work_func pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : devm_free_irq+0x74/0x80 lr : devm_free_irq+0x48/0x80 Call trace: devm_free_irq+0x74/0x80 (P) devm_free_irq+0x48/0x80 (L) fsl_edma_remove+0xc4/0xc8 platform_remove+0x28/0x44 device_remove+0x4c/0x80

In the Linux kernel, the following vulnerability has been resolved: f2fs: compress: fix UAF of f2fs_inode_info in f2fs_free_dic The decompress_io_ctx may be released asynchronously after I/O completion. If this file is deleted immediately after read, and the kworker of processing post_read_wq has not been executed yet due to high workloads, It is possible that the inode(f2fs_inode_info) is evicted and freed before it is used f2fs_free_dic. The UAF case as below: Thread A Thread B - f2fs_decompress_end_io - f2fs_put_dic - queue_work add free_dic work to post_read_wq - do_unlink - iput - evict - call_rcu This file is deleted after read. Thread C kworker to process post_read_wq - rcu_do_batch - f2fs_free_inode - kmem_cache_free inode is freed by rcu - process_scheduled_works - f2fs_late_free_dic - f2fs_free_dic - f2fs_release_decomp_mem read (dic->inode)->i_compress_algorithm This patch store compress_algorithm and sbi in dic to avoid inode UAF. In addition, the previous solution is deprecated in [1] may cause system hang. [1] https://lore.kernel.org/all/c36ab955-c8db-4a8b-a9d0-f07b5f426c3f@kernel.org

In the Linux kernel, the following vulnerability has been resolved: can: xilinx_can: xcan_write_frame(): fix use-after-free of transmitted SKB can_put_echo_skb() takes ownership of the SKB and it may be freed during or after the call. However, xilinx_can xcan_write_frame() keeps using SKB after the call. Fix that by only calling can_put_echo_skb() after the code is done touching the SKB. The tx_lock is held for the entire xcan_write_frame() execution and also on the can_get_echo_skb() side so the order of operations does not matter. An earlier fix commit 3d3c817c3a40 ("can: xilinx_can: Fix usage of skb memory") did not move the can_put_echo_skb() call far enough. [mkl: add "commit" in front of sha1 in patch description] [mkl: fix indention]

In the Linux kernel, the following vulnerability has been resolved: ipv6: reject malicious packets in ipv6_gso_segment() syzbot was able to craft a packet with very long IPv6 extension headers leading to an overflow of skb->transport_header. This 16bit field has a limited range. Add skb_reset_transport_header_careful() helper and use it from ipv6_gso_segment() WARNING: CPU: 0 PID: 5871 at ./include/linux/skbuff.h:3032 skb_reset_transport_header include/linux/skbuff.h:3032 [inline] WARNING: CPU: 0 PID: 5871 at ./include/linux/skbuff.h:3032 ipv6_gso_segment+0x15e2/0x21e0 net/ipv6/ip6_offload.c:151 Modules linked in: CPU: 0 UID: 0 PID: 5871 Comm: syz-executor211 Not tainted 6.16.0-rc6-syzkaller-g7abc678e3084 #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/12/2025 RIP: 0010:skb_reset_transport_header include/linux/skbuff.h:3032 [inline] RIP: 0010:ipv6_gso_segment+0x15e2/0x21e0 net/ipv6/ip6_offload.c:151 Call Trace: <TASK> skb_mac_gso_segment+0x31c/0x640 net/core/gso.c:53 nsh_gso_segment+0x54a/0xe10 net/nsh/nsh.c:110 skb_mac_gso_segment+0x31c/0x640 net/core/gso.c:53 __skb_gso_segment+0x342/0x510 net/core/gso.c:124 skb_gso_segment include/net/gso.h:83 [inline] validate_xmit_skb+0x857/0x11b0 net/core/dev.c:3950 validate_xmit_skb_list+0x84/0x120 net/core/dev.c:4000 sch_direct_xmit+0xd3/0x4b0 net/sched/sch_generic.c:329 __dev_xmit_skb net/core/dev.c:4102 [inline] __dev_queue_xmit+0x17b6/0x3a70 net/core/dev.c:4679

In the Linux kernel, the following vulnerability has been resolved: lib/crypto: arm/poly1305: Fix register corruption in no-SIMD contexts Restore the SIMD usability check that was removed by commit 773426f4771b ("crypto: arm/poly1305 - Add block-only interface"). This safety check is cheap and is well worth eliminating a footgun. While the Poly1305 functions should not be called when SIMD registers are unusable, if they are anyway, they should just do the right thing instead of corrupting random tasks' registers and/or computing incorrect MACs. Fixing this is also needed for poly1305_kunit to pass. Just use may_use_simd() instead of the original crypto_simd_usable(), since poly1305_kunit won't rely on crypto_simd_disabled_for_test.

In the Linux kernel, the following vulnerability has been resolved: net: libwx: fix the using of Rx buffer DMA The wx_rx_buffer structure contained two DMA address fields: 'dma' and 'page_dma'. However, only 'page_dma' was actually initialized and used to program the Rx descriptor. But 'dma' was uninitialized and used in some paths. This could lead to undefined behavior, including DMA errors or use-after-free, if the uninitialized 'dma' was used. Althrough such error has not yet occurred, it is worth fixing in the code.

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: host: Detect events pointing to unexpected TREs When a remote device sends a completion event to the host, it contains a pointer to the consumed TRE. The host uses this pointer to process all of the TREs between it and the host's local copy of the ring's read pointer. This works when processing completion for chained transactions, but can lead to nasty results if the device sends an event for a single-element transaction with a read pointer that is multiple elements ahead of the host's read pointer. For instance, if the host accesses an event ring while the device is updating it, the pointer inside of the event might still point to an old TRE. If the host uses the channel's xfer_cb() to directly free the buffer pointed to by the TRE, the buffer will be double-freed. This behavior was observed on an ep that used upstream EP stack without 'commit 6f18d174b73d ("bus: mhi: ep: Update read pointer only after buffer is written")'. Where the device updated the events ring pointer before updating the event contents, so it left a window where the host was able to access the stale data the event pointed to, before the device had the chance to update them. The usual pattern was that the host received an event pointing to a TRE that is not immediately after the last processed one, so it got treated as if it was a chained transaction, processing all of the TREs in between the two read pointers. This commit aims to harden the host by ensuring transactions where the event points to a TRE that isn't local_rp + 1 are chained. [mani: added stable tag and reworded commit message]

In the Linux kernel, the following vulnerability has been resolved: fs/buffer: fix use-after-free when call bh_read() helper There's issue as follows: BUG: KASAN: stack-out-of-bounds in end_buffer_read_sync+0xe3/0x110 Read of size 8 at addr ffffc9000168f7f8 by task swapper/3/0 CPU: 3 UID: 0 PID: 0 Comm: swapper/3 Not tainted 6.16.0-862.14.0.6.x86_64 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) Call Trace: <IRQ> dump_stack_lvl+0x55/0x70 print_address_description.constprop.0+0x2c/0x390 print_report+0xb4/0x270 kasan_report+0xb8/0xf0 end_buffer_read_sync+0xe3/0x110 end_bio_bh_io_sync+0x56/0x80 blk_update_request+0x30a/0x720 scsi_end_request+0x51/0x2b0 scsi_io_completion+0xe3/0x480 ? scsi_device_unbusy+0x11e/0x160 blk_complete_reqs+0x7b/0x90 handle_softirqs+0xef/0x370 irq_exit_rcu+0xa5/0xd0 sysvec_apic_timer_interrupt+0x6e/0x90 </IRQ> Above issue happens when do ntfs3 filesystem mount, issue may happens as follows: mount IRQ ntfs_fill_super read_cache_page do_read_cache_folio filemap_read_folio mpage_read_folio do_mpage_readpage ntfs_get_block_vbo bh_read submit_bh wait_on_buffer(bh); blk_complete_reqs scsi_io_completion scsi_end_request blk_update_request end_bio_bh_io_sync end_buffer_read_sync __end_buffer_read_notouch unlock_buffer wait_on_buffer(bh);--> return will return to caller put_bh --> trigger stack-out-of-bounds In the mpage_read_folio() function, the stack variable 'map_bh' is passed to ntfs_get_block_vbo(). Once unlock_buffer() unlocks and wait_on_buffer() returns to continue processing, the stack variable is likely to be reclaimed. Consequently, during the end_buffer_read_sync() process, calling put_bh() may result in stack overrun. If the bh is not allocated on the stack, it belongs to a folio. Freeing a buffer head which belongs to a folio is done by drop_buffers() which will fail to free buffers which are still locked. So it is safe to call put_bh() before __end_buffer_read_notouch().

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: fix use-after-free in cmp_bss() Following bss_free() quirk introduced in commit 776b3580178f ("cfg80211: track hidden SSID networks properly"), adjust cfg80211_update_known_bss() to free the last beacon frame elements only if they're not shared via the corresponding 'hidden_beacon_bss' pointer.

In the Linux kernel, the following vulnerability has been resolved: iommu/s390: Fix memory corruption when using identity domain zpci_get_iommu_ctrs() returns counter information to be reported as part of device statistics; these counters are stored as part of the s390_domain. The problem, however, is that the identity domain is not backed by an s390_domain and so the conversion via to_s390_domain() yields a bad address that is zero'd initially and read on-demand later via a sysfs read. These counters aren't necessary for the identity domain; just return NULL in this case. This issue was discovered via KASAN with reports that look like: BUG: KASAN: global-out-of-bounds in zpci_fmb_enable_device when using the identity domain for a device on s390.

In the Linux kernel, the following vulnerability has been resolved: jfs: truncate good inode pages when hard link is 0 The fileset value of the inode copy from the disk by the reproducer is AGGR_RESERVED_I. When executing evict, its hard link number is 0, so its inode pages are not truncated. This causes the bugon to be triggered when executing clear_inode() because nrpages is greater than 0.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix use-after-free in cifs_oplock_break A race condition can occur in cifs_oplock_break() leading to a use-after-free of the cinode structure when unmounting: cifs_oplock_break() _cifsFileInfo_put(cfile) cifsFileInfo_put_final() cifs_sb_deactive() [last ref, start releasing sb] kill_sb() kill_anon_super() generic_shutdown_super() evict_inodes() dispose_list() evict() destroy_inode() call_rcu(&inode->i_rcu, i_callback) spin_lock(&cinode->open_file_lock) <- OK [later] i_callback() cifs_free_inode() kmem_cache_free(cinode) spin_unlock(&cinode->open_file_lock) <- UAF cifs_done_oplock_break(cinode) <- UAF The issue occurs when umount has already released its reference to the superblock. When _cifsFileInfo_put() calls cifs_sb_deactive(), this releases the last reference, triggering the immediate cleanup of all inodes under RCU. However, cifs_oplock_break() continues to access the cinode after this point, resulting in use-after-free. Fix this by holding an extra reference to the superblock during the entire oplock break operation. This ensures that the superblock and its inodes remain valid until the oplock break completes.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix out-of-bounds dynptr write in bpf_crypto_crypt Stanislav reported that in bpf_crypto_crypt() the destination dynptr's size is not validated to be at least as large as the source dynptr's size before calling into the crypto backend with 'len = src_len'. This can result in an OOB write when the destination is smaller than the source. Concretely, in mentioned function, psrc and pdst are both linear buffers fetched from each dynptr: psrc = __bpf_dynptr_data(src, src_len); [...] pdst = __bpf_dynptr_data_rw(dst, dst_len); [...] err = decrypt ? ctx->type->decrypt(ctx->tfm, psrc, pdst, src_len, piv) : ctx->type->encrypt(ctx->tfm, psrc, pdst, src_len, piv); The crypto backend expects pdst to be large enough with a src_len length that can be written. Add an additional src_len > dst_len check and bail out if it's the case. Note that these kfuncs are accessible under root privileges only.

In the Linux kernel, the following vulnerability has been resolved: perf/core: Exit early on perf_mmap() fail When perf_mmap() fails to allocate a buffer, it still invokes the event_mapped() callback of the related event. On X86 this might increase the perf_rdpmc_allowed reference counter. But nothing undoes this as perf_mmap_close() is never called in this case, which causes another reference count leak. Return early on failure to prevent that.

In the Linux kernel, the following vulnerability has been resolved: staging: media: atomisp: Fix stack buffer overflow in gmin_get_var_int() When gmin_get_config_var() calls efi.get_variable() and the EFI variable is larger than the expected buffer size, two behaviors combine to create a stack buffer overflow: 1. gmin_get_config_var() does not return the proper error code when efi.get_variable() fails. It returns the stale 'ret' value from earlier operations instead of indicating the EFI failure. 2. When efi.get_variable() returns EFI_BUFFER_TOO_SMALL, it updates *out_len to the required buffer size but writes no data to the output buffer. However, due to bug #1, gmin_get_var_int() believes the call succeeded. The caller gmin_get_var_int() then performs: - Allocates val[CFG_VAR_NAME_MAX + 1] (65 bytes) on stack - Calls gmin_get_config_var(dev, is_gmin, var, val, &len) with len=64 - If EFI variable is >64 bytes, efi.get_variable() sets len=required_size - Due to bug #1, thinks call succeeded with len=required_size - Executes val[len] = 0, writing past end of 65-byte stack buffer This creates a stack buffer overflow when EFI variables are larger than 64 bytes. Since EFI variables can be controlled by firmware or system configuration, this could potentially be exploited for code execution. Fix the bug by returning proper error codes from gmin_get_config_var() based on EFI status instead of stale 'ret' value. The gmin_get_var_int() function is called during device initialization for camera sensor configuration on Intel Bay Trail and Cherry Trail platforms using the atomisp camera stack.

In the Linux kernel, the following vulnerability has been resolved: ipv6: mcast: Delay put pmc->idev in mld_del_delrec() pmc->idev is still used in ip6_mc_clear_src(), so as mld_clear_delrec() does, the reference should be put after ip6_mc_clear_src() return.

In the Linux kernel, the following vulnerability has been resolved: mm/damon/sysfs: fix use-after-free in state_show() state_show() reads kdamond->damon_ctx without holding damon_sysfs_lock. This allows a use-after-free race: CPU 0 CPU 1 ----- ----- state_show() damon_sysfs_turn_damon_on() ctx = kdamond->damon_ctx; mutex_lock(&damon_sysfs_lock); damon_destroy_ctx(kdamond->damon_ctx); kdamond->damon_ctx = NULL; mutex_unlock(&damon_sysfs_lock); damon_is_running(ctx); /* ctx is freed */ mutex_lock(&ctx->kdamond_lock); /* UAF */ (The race can also occur with damon_sysfs_kdamonds_rm_dirs() and damon_sysfs_kdamond_release(), which free or replace the context under damon_sysfs_lock.) Fix by taking damon_sysfs_lock before dereferencing the context, mirroring the locking used in pid_show(). The bug has existed since state_show() first accessed kdamond->damon_ctx.

In the Linux kernel, the following vulnerability has been resolved: iommu/s390: Make attach succeed when the device was surprise removed When a PCI device is removed with surprise hotplug, there may still be attempts to attach the device to the default domain as part of tear down via (__iommu_release_dma_ownership()), or because the removal happens during probe (__iommu_probe_device()). In both cases zpci_register_ioat() fails with a cc value indicating that the device handle is invalid. This is because the device is no longer part of the instance as far as the hypervisor is concerned. Currently this leads to an error return and s390_iommu_attach_device() fails. This triggers the WARN_ON() in __iommu_group_set_domain_nofail() because attaching to the default domain must never fail. With the device fenced by the hypervisor no DMAs to or from memory are possible and the IOMMU translations have no effect. Proceed as if the registration was successful and let the hotplug event handling clean up the device. This is similar to how devices in the error state are handled since commit 59bbf596791b ("iommu/s390: Make attach succeed even if the device is in error state") except that for removal the domain will not be registered later. This approach was also previously discussed at the link. Handle both cases, error state and removal, in a helper which checks if the error needs to be propagated or ignored. Avoid magic number condition codes by using the pre-existing, but never used, defines for PCI load/store condition codes and rename them to reflect that they apply to all PCI instructions.

In the Linux kernel, the following vulnerability has been resolved: iio: accel: fxls8962af: Fix use after free in fxls8962af_fifo_flush fxls8962af_fifo_flush() uses indio_dev->active_scan_mask (with iio_for_each_active_channel()) without making sure the indio_dev stays in buffer mode. There is a race if indio_dev exits buffer mode in the middle of the interrupt that flushes the fifo. Fix this by calling synchronize_irq() to ensure that no interrupt is currently running when disabling buffer mode. Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read [...] _find_first_bit_le from fxls8962af_fifo_flush+0x17c/0x290 fxls8962af_fifo_flush from fxls8962af_interrupt+0x80/0x178 fxls8962af_interrupt from irq_thread_fn+0x1c/0x7c irq_thread_fn from irq_thread+0x110/0x1f4 irq_thread from kthread+0xe0/0xfc kthread from ret_from_fork+0x14/0x2c

In the Linux kernel, the following vulnerability has been resolved: habanalabs: fix UAF in export_dmabuf() As soon as we'd inserted a file reference into descriptor table, another thread could close it. That's fine for the case when all we are doing is returning that descriptor to userland (it's a race, but it's a userland race and there's nothing the kernel can do about it). However, if we follow fd_install() with any kind of access to objects that would be destroyed on close (be it the struct file itself or anything destroyed by its ->release()), we have a UAF. dma_buf_fd() is a combination of reserving a descriptor and fd_install(). habanalabs export_dmabuf() calls it and then proceeds to access the objects destroyed on close. In particular, it grabs an extra reference to another struct file that will be dropped as part of ->release() for ours; that "will be" is actually "might have already been". Fix that by reserving descriptor before anything else and do fd_install() only when everything had been set up. As a side benefit, we no longer have the failure exit with file already created, but reference to underlying file (as well as ->dmabuf_export_cnt, etc.) not grabbed yet; unlike dma_buf_fd(), fd_install() can't fail.

In the Linux kernel, the following vulnerability has been resolved: net/sched: Make cake_enqueue return NET_XMIT_CN when past buffer_limit The following setup can trigger a WARNING in htb_activate due to the condition: !cl->leaf.q->q.qlen tc qdisc del dev lo root tc qdisc add dev lo root handle 1: htb default 1 tc class add dev lo parent 1: classid 1:1 \ htb rate 64bit tc qdisc add dev lo parent 1:1 handle f: \ cake memlimit 1b ping -I lo -f -c1 -s64 -W0.001 127.0.0.1 This is because the low memlimit leads to a low buffer_limit, which causes packet dropping. However, cake_enqueue still returns NET_XMIT_SUCCESS, causing htb_enqueue to call htb_activate with an empty child qdisc. We should return NET_XMIT_CN when packets are dropped from the same tin and flow. I do not believe return value of NET_XMIT_CN is necessary for packet drops in the case of ack filtering, as that is meant to optimize performance, not to signal congestion.

In the Linux kernel, the following vulnerability has been resolved: dmaengine: nbpfaxi: Fix memory corruption in probe() The nbpf->chan[] array is allocated earlier in the nbpf_probe() function and it has "num_channels" elements. These three loops iterate one element farther than they should and corrupt memory. The changes to the second loop are more involved. In this case, we're copying data from the irqbuf[] array into the nbpf->chan[] array. If the data in irqbuf[i] is the error IRQ then we skip it, so the iterators are not in sync. I added a check to ensure that we don't go beyond the end of the irqbuf[] array. I'm pretty sure this can't happen, but it seemed harmless to add a check. On the other hand, after the loop has ended there is a check to ensure that the "chan" iterator is where we expect it to be. In the original code we went one element beyond the end of the array so the iterator wasn't in the correct place and it would always return -EINVAL. However, now it will always be in the correct place. I deleted the check since we know the result.