A vulnerability has been found in TOTOLINK AC1200 T8 4.1.5cu.861_B20230220 and classified as critical. This vulnerability affects the function setParentalRules of the file /cgi-bin/cstecgi.cgi. The manipulation of the argument slaveIpList leads to os command injection. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability, which was classified as critical, was found in TOTOLINK EX1200L 9.3.5u.6146_B20201023. Affected is the function setDefResponse of the file /www/cgi-bin/cstecgi.cgi. The manipulation of the argument IpAddress leads to stack-based buffer overflow. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability has been found in TOTOLINK EX1200L 9.3.5u.6146_B20201023 and classified as critical. Affected by this vulnerability is the function setLanguageCfg of the file /www/cgi-bin/cstecgi.cgi. The manipulation of the argument langType leads to stack-based buffer overflow. The attack can be launched remotely. The exploit has been disclosed to the public and may be used. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability has been found in TOTOLINK LR350 9.3.5u.6369_B20220309 and classified as critical. Affected by this vulnerability is the function setWanCfg of the file /cgi-bin/cstecgi.cgi. The manipulation of the argument hostName leads to command injection. The attack can be launched remotely. The exploit has been disclosed to the public and may be used. The identifier VDB-272785 was assigned to this vulnerability. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability has been found in TOTOLINK A3600R 4.1.2cu.5182_B20201102 and classified as critical. This vulnerability affects the function setDiagnosisCfg of the file /cgi-bin/cstecgi.cgi. The manipulation of the argument ipDoamin leads to os command injection. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. The identifier of this vulnerability is VDB-272596. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in TOTOLINK A3100R 4.1.2cu.5050_B20200504. It has been declared as critical. This vulnerability affects the function setTelnetCfg of the file /cgi-bin/cstecgi.cgi of the component HTTP POST Request Handler. The manipulation of the argument telnet_enabled leads to command injection. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. The identifier of this vulnerability is VDB-272572. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability classified as critical has been found in TOTOLINK A3600R 4.1.2cu.5182_B20201102. Affected is the function NTPSyncWithHost of the file /cgi-bin/cstecgi.cgi. The manipulation of the argument hostTime leads to os command injection. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. The identifier of this vulnerability is VDB-272592. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in TOTOLINK LR1200 9.3.1cu.2832 and classified as critical. Affected by this issue is the function NTPSyncWithHost of the file /cgi-bin/cstecgi.cgi. The manipulation of the argument host_time leads to command injection. The attack may be launched remotely. The exploit has been disclosed to the public and may be used. VDB-272786 is the identifier assigned to this vulnerability. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability classified as critical was found in TOTOLINK A3600R 4.1.2cu.5182_B20201102. This vulnerability affects the function setTelnetCfg of the file /cgi-bin/cstecgi.cgi. The manipulation of the argument telnet_enabled leads to command injection. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. VDB-272602 is the identifier assigned to this vulnerability. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability classified as critical has been found in TOTOLINK A3700R 9.1.2u.5822_B20200513. Affected is the function setWanCfg of the file /cgi-bin/cstecgi.cgi. The manipulation of the argument hostName leads to command injection. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. VDB-272574 is the identifier assigned to this vulnerability. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was detected in TOTOLINK A702R 4.0.0-B20211108.1423. Affected by this vulnerability is the function sub_4162DC of the file /boafrm/formFilter. The manipulation of the argument ip6addr results in buffer overflow. It is possible to launch the attack remotely. The exploit is now public and may be used.

A flaw has been found in TOTOLINK A702R 4.0.0-B20211108.1423. Affected by this issue is the function sub_419BE0 of the file /boafrm/formIpQoS. This manipulation of the argument mac causes buffer overflow. The attack can be initiated remotely. The exploit has been published and may be used.

A vulnerability has been found in TOTOLINK A702R 4.0.0-B20211108.1423. This affects the function sub_4162DC of the file /boafrm/formFilter. Such manipulation of the argument ip6addr leads to buffer overflow. The attack can be launched remotely. The exploit has been disclosed to the public and may be used.

A vulnerability, which was classified as critical, has been found in TOTOLINK EX1200T 4.1.2cu.5232_B20210713. This issue affects the function setLanguageCfg of the file /cgi-bin/cstecgi.cgi. The manipulation of the argument LangType leads to stack-based buffer overflow. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used.

A vulnerability classified as problematic was found in TOTOLINK EX1800T 9.1.0cu.2112_B20220316. This vulnerability affects the function sub_40662C of the file /cgi-bin/cstecgi.cgi. The manipulation of the argument ssid leads to stack-based buffer overflow. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used.

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

Microsoft Exchange Server Remote Code Execution Vulnerability

A buffer overflow in the httpd daemon on TP-Link TL-WR841N V12 (firmware version 3.16.9) devices allows an authenticated remote attacker to execute arbitrary code via a GET request to the page for the System Tools of the Wi-Fi network. This affects TL-WR841 V12 TL-WR841N(EU)_V12_160624 and TL-WR841 V11 TL-WR841N(EU)_V11_160325 , TL-WR841N_V11_150616 and TL-WR841 V10 TL-WR841N_V10_150310 are also affected.

A vulnerability was found in Tenda FH1206 1.2.0.8(8155) and classified as critical. This issue affects the function fromAddressNat of the file /goform/addressNat. The manipulation of the argument entrys leads to buffer overflow. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used. The associated identifier of this vulnerability is VDB-261671. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

In Tensorflow before versions 1.15.4, 2.0.3, 2.1.2, 2.2.1 and 2.3.1, the implementation of `SparseFillEmptyRowsGrad` uses a double indexing pattern. It is possible for `reverse_index_map(i)` to be an index outside of bounds of `grad_values`, thus resulting in a heap buffer overflow. The issue is patched in commit 390611e0d45c5793c7066110af37c8514e6a6c54, and is released in TensorFlow versions 1.15.4, 2.0.3, 2.1.2, 2.2.1, or 2.3.1.

A heap overflow vulnerability in Citrix NetScaler Gateway versions 10.1 before 135.8/135.12, 10.5 before 65.11, 11.0 before 70.12, and 11.1 before 52.13 allows a remote authenticated attacker to run arbitrary commands via unspecified vectors.

A vulnerability was determined in Tenda CH22 1.0.0.1. Affected by this issue is the function fromIpsecitem of the file /goform/IPSECsave of the component httpd. Executing manipulation of the argument ipsecno can lead to stack-based buffer overflow. The attack may be performed from remote.

TP-LINK NC200 devices through 2.1.10 build 200401, NC210 devices through 1.0.10 build 200401, NC220 devices through 1.3.1 build 200401, NC230 devices through 1.3.1 build 200401, NC250 devices through 1.3.1 build 200401, NC260 devices through 1.5.3 build_200401, and NC450 devices through 1.5.4 build 200401 have a Buffer Overflow

Buffer overflow in Microsoft SQL Server 2005 SP1 and SP2, and 2005 Express Edition SP1 and SP2, allows remote authenticated users to execute arbitrary code via a crafted insert statement.

In LoRaMac-node before 4.4.4, a reception buffer overflow can happen due to the received buffer size not being checked. This has been fixed in 4.4.4.

Buffer overflow in logout.cgi in the Intelligent Platform Management Interface (IPMI) with firmware before 3.15 (SMT_X9_315) on Supermicro X9 generation motherboards allows remote authenticated users to execute arbitrary code via the SID parameter.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

Multiple buffer overflows in (a) UltraVNC (aka Ultr@VNC) 1.0.1 and earlier and (b) tabbed_viewer 1.29 (1) allow user-assisted remote attackers to execute arbitrary code via a malicious server that sends a long string to a client that connects on TCP port 5900, which triggers an overflow in Log::ReallyPrint; and (2) allow remote attackers to cause a denial of service (server crash) via a long HTTP GET request to TCP port 5800, which triggers an overflow in VNCLog::ReallyPrint.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

A buffer overflow issue was addressed with improved memory handling. This issue is fixed in macOS Mojave 10.14.6, Security Update 2019-004 High Sierra, Security Update 2019-004 Sierra. An attacker in a privileged network position may be able to execute arbitrary code.

spice versions though 0.13 are vulnerable to out-of-bounds memory access when processing specially crafted messages from authenticated attacker to the spice server resulting into crash and/or server memory leak.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

Remote code execution can occur in Asterisk Open Source 13.x before 13.14.1 and 14.x before 14.3.1 and Certified Asterisk 13.13 before 13.13-cert3 because of a buffer overflow in a CDR user field, related to X-ClientCode in chan_sip, the CDR dialplan function, and the AMI Monitor action.

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

A buffer overflow issue was addressed with improved memory handling. This issue is fixed in macOS Mojave 10.14.6, Security Update 2019-004 High Sierra, Security Update 2019-004 Sierra. An attacker in a privileged network position may be able to execute arbitrary code.

Multiple buffer overflows in the (1) SNMP and (2) License Manager implementations in Cisco NX-OS on Nexus 7000 devices 4.x and 5.x before 5.2(5) and 6.x before 6.1(1) and MDS 9000 devices 4.x and 5.x before 5.2(5) allow remote authenticated users to execute arbitrary code via a crafted SNMP request, aka Bug ID CSCtx54830.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

Stack-based buffer overflow in the reslist function in ntpq in NTP before 4.2.8p10 and 4.3.x before 4.3.94 allows remote servers have unspecified impact via a long flagstr variable in a restriction list response.

Tp-Link TL-WR840N (EU) v6.20 Firmware (0.9.1 4.17 v0001.0 Build 201124 Rel.64328n) is vulnerable to Buffer Overflow via the Password reset feature.

Buffer overflow in SonicWall SMA100 allows an authenticated user to execute arbitrary code in DEARegister CGI script. This vulnerability impacted SMA100 version 9.0.0.3 and earlier.

Multiple buffer overflows in FlashFXP.exe in FlashFXP 4.2 allow remote authenticated users to execute arbitrary code via a long unicode string to (1) TListbox or (2) TComboBox.

NETGEAR R8000 devices before 1.0.4.62 are affected by a buffer overflow by an authenticated user.

Certain NETGEAR devices are affected by a buffer overflow by an authenticated user. This affects EX7000 before 1.0.1.80, R6400 before 1.0.1.50, R6400v2 before 1.0.4.118, R6700 before 1.0.2.8, R6700v3 before 1.0.4.118, R6900 before 1.0.2.8, R6900P before 1.3.2.124, R7000 before 1.0.9.88, R7000P before 1.3.2.124, R7900 before 1.0.3.18, R7900P before 1.4.1.50, R8000 before 1.0.4.46, R8000P before 1.4.1.50, RAX80 before 1.0.1.56, and WNR3500Lv2 before 1.2.0.62.

Certain NETGEAR devices are affected by a buffer overflow by an authenticated user. This affects EX6000 before 1.0.0.38, EX6120 before 1.0.0.48, EX6130 before 1.0.0.30, R6300v2 before 1.0.4.52, R6400 before 1.0.1.52, R7000 before 1.0.11.126, R7900 before 1.0.4.30, R8000 before 1.0.4.52, R7000P before 1.3.2.124, R8000P before 1.4.1.50, RAX80 before 1.0.3.88, R6900P before 1.3.2.124, R7900P before 1.4.1.50, and RAX75 before 1.0.3.88.

Buffer overflow in IBM Informix 11.50 through 11.50.xC9W2 and 11.70 before 11.70.xC7 allows remote authenticated users to execute arbitrary code via a crafted SQL statement.

Apache PLC4X - PLC4C (Only the C language implementation was effected) was vulnerable to an unsigned integer underflow flaw inside the tcp transport. Users should update to 0.9.1, which addresses this issue. However, in order to exploit this vulnerability, a user would have to actively connect to a mallicious device which could send a response with invalid content. Currently we consider the probability of this being exploited as quite minimal, however this could change in the future, especially with the industrial networks growing more and more together.

Stack-based buffer overflow in the eap_do_notify function in eap.c in xsupplicant before 1.2.6, and possibly other versions, allows remote authenticated users to execute arbitrary code via unspecified vectors.