The bluetooth HCI host layer logic not clearing a global reference to a semaphore after synchronously sending HCI commands may allow a malicious HCI Controller to cause the use of a dangling reference in the host layer, leading to a crash (DoS) or potential RCE on the Host layer.

An integer underflow in bt_mesh_sol_recv() in the Bluetooth Mesh solicitation handling (subsys/bluetooth/mesh/solicitation.c) leads to an out-of-bounds write. When CONFIG_BT_MESH_OD_PRIV_PROXY_SRV is enabled, the function parses solicitation PDUs from raw BLE advertising payloads. The AD parsing loop reads an attacker-controlled length byte (reported_len) and computes reported_len - 3 without checking that reported_len >= 3. When reported_len is less than 3, the subtraction is performed in signed int arithmetic and yields a negative value that bypasses the length guard and is then implicitly converted to a very large size_t when passed to net_buf_simple_pull_mem(). In builds without assertions, this wraps the buffer length and advances the data pointer far out of bounds, so subsequent reads dereference invalid memory. A nearby BLE device can trigger this with a non-connectable advertisement carrying a UUID16 AD structure and a crafted length byte, with no pairing or prior association required, potentially leading to denial of service or arbitrary code execution.

A remote, unauthenticated BLE peer can trigger a 2-byte out-of-bounds write in the Bluetooth host during L2CAP LE CoC SDU reassembly. When the application enables segmentation (via chan_ops.alloc_buf) and the chosen RX pool has a user_data_size smaller than 2 bytes, the segmentation counter stored in the net_buf user_data area is written out of bounds in l2cap_chan_le_recv_seg (subsys/bluetooth/host/l2cap.c). The observed effects are an AddressSanitizer abort and, without ASan, heap corruption / fatal error.

A remote, unauthenticated attacker can trigger memory corruption in Zephyr's HTTP server WebSocket upgrade path by sending a crafted Sec-WebSocket-Key header. The HTTP/1 header parser copies the header into a fixed-size buffer using a bounded copy that does not guarantee NUL termination when the input length reaches the buffer size. During upgrade handling the buffer is copied to a local stack buffer and passed to strlen(); if no NUL exists in-bounds, strlen() reads beyond the stack buffer and subsequent concatenation with the WebSocket magic string can write out of bounds. This leads to out-of-bounds read and write on stack memory, resulting in crash (denial of service) and potentially code execution. The path is reachable when CONFIG_HTTP_SERVER_WEBSOCKET is enabled.

A potential out-of-bounds write/read exists in the TLS socket connect path of the network sockets subsystem (subsys/net/lib/sockets/sockets_tls.c). When the TLS session cache is enabled, tls_session_store() and tls_session_restore() memcpy the caller-supplied address into a fixed-size buffer using the caller-controlled addrlen value without validating it against the destination size. struct net_sockaddr is an opaque type, so an application can pass an addrlen larger than sizeof(struct net_sockaddr) (for example 128 bytes into a 24-byte stack buffer), causing the memcpy to read and write past the end of the address memory used by the TLS session cache. This out-of-bounds write can lead to a crash and denial of service, and potentially to arbitrary code execution.

Possible variant of CVE-2021-3434 in function le_ecred_reconf_req.

Unchecked length coming from user input in settings shell

can: out of bounds in remove_rx_filter function

bt_iso_recv() in subsys/bluetooth/host/iso.c pulled the ISO SDU header (4 bytes) or, when the timestamp flag is set, the timestamped SDU header (8 bytes) from the inbound HCI ISO Data buffer via net_buf_pull_mem() without first checking buf->len. The upstream hci_iso() handler enforces buf->len == the controller-declared ISO Data_Load length, so a malicious or buggy controller / adjacent BLE peer on an established CIS/BIS can present a first-fragment (BT_ISO_START) or single (BT_ISO_SINGLE) PDU shorter than the SDU header. Because net_buf_simple_pull_mem only guards length with __ASSERT_NO_MSG (compiled out when CONFIG_ASSERT is disabled, the production default), the pull underflows buf->len (uint16_t, e.g. 0 - 8 = 0xFFF8) and advances buf->data past valid data: the subsequent reads of hdr->slen and hdr->sn are out-of-bounds reads of adjacent pool memory. For the multi-fragment (START) case the corrupted buffer is retained as iso->rx, and a following CONT/END fragment's net_buf_tailroom() guard underflows to a near-SIZE_MAX value, defeating the bounds check and causing net_buf_add_mem() to memcpy attacker-supplied fragment data far past the RX pool buffer (out-of-bounds write). The flaw affects ISO receive builds (CONFIG_BT_ISO_RX, selected by the default-off LE Audio options BT_ISO_PERIPHERAL/BT_ISO_CENTRAL/BT_ISO_SYNC_RECEIVER) and has existed since the ISO subsystem was introduced (v2.6.0) through v4.4.0. The fix adds explicit buf->len < sizeof(ts_hdr) and buf->len < sizeof(hdr) checks that drop the buffer before pulling.

In subsys/net/ip/tcp.c , function tcp_flags , when the incoming parameter flags is ECN or CWR , the buf will out-of-bounds write a byte zero.

Zephyr's Bluetooth Classic Hands-Free Profile (HFP) Hands-Free role parser (subsys/bluetooth/host/classic/hfp_hf.c) contains an out-of-bounds write. During Service Level Connection setup the HF sends AT+CIND=? and parses the AG's +CIND: response in cind_handle(), which assigns a per-entry counter index and calls cind_handle_values() for each list element. cind_handle_values() then wrote hf->ind_table[index] = i without verifying that index is within the 20-element int8_t ind_table[] array of struct bt_hfp_hf. Because the parser places no cap on the number of +CIND: list entries, a remote Attendant Gateway (a malicious, compromised, or spoofed peer the device connects to over Bluetooth) can send a response with more than 20 recognized indicator entries and drive index arbitrarily large, writing a small attacker-positioned value past the array into adjacent struct fields (feature masks, SDP/version state, the calls[] array, work/atomic bookkeeping) and potentially beyond the static connection pool slot. This yields memory corruption and at least denial of service of the Bluetooth host, triggered by a single malformed AT response with no user interaction. The sibling consumer ag_indicator_handle_values() already performed the equivalent bounds check; this commit adds the same index >= ARRAY_SIZE(hf->ind_table) guard to close the gap. Affects builds with CONFIG_BT_HFP_HF enabled; introduced with the original HFP HF CIND parser (~v1.7) and present through v4.4.0.

In Zephyr bluetooth mesh core stack, an out-of-bound write vulnerability can be triggered during provisioning.

In gnss service, there is a possible out of bounds write due to an incorrect bounds check. This could lead to local escalation of privilege if a malicious actor has already obtained the System privilege. User interaction is not needed for exploitation. Patch ID: ALPS10010443; Issue ID: MSV-3966.

In DA, there is a possible out of bounds write due to a missing bounds check. This could lead to local escalation of privilege, if an attacker has physical access to the device, with no additional execution privileges needed. User interaction is needed for exploitation. Patch ID: ALPS09915215; Issue ID: MSV-3801.

In Zephyr bluetooth mesh core stack, an out-of-bound write vulnerability can be triggered during provisioning.

No proper validation of the length of user input in olcp_ind_handler in zephyr/subsys/bluetooth/services/ots/ots_client.c.

On Xtensa SoCs built with CONFIG_XTENSA_MPU and CONFIG_USERSPACE, arch_buffer_validate() in arch/xtensa/core/mpu.c — the architecture hook that verifies a user-mode-supplied buffer is accessible to the calling user thread with the requested permission — defaulted its return value to 0 (access permitted) and only set a denial result inside its per-MPU-region probe loop. When the rounded extent of the buffer wraps the 32-bit address space (size + alignment offset near SIZE_MAX, or ROUND_UP(size + offset) overflowing to 0), the loop executes zero iterations and the function returns 0 = permitted without probing any MPU region. The syscall-layer pre-checks (K_SYSCALL_MEMORY_SIZE_CHECK / Z_DETECT_POINTER_OVERFLOW) only catch a raw addr+size wrap and do not cover the ROUND_UP-induced wrap, and the string path (arch_user_string_nlen -> arch_buffer_validate) has no syscall-layer guard at all. An unprivileged user-mode thread can therefore pass a crafted (addr, size) to any syscall that validates user buffers via k_usermode_from_copy/to_copy or k_usermode_string_copy and have validation succeed for memory it must not access; the kernel then reads from (disclosure) or, with write=1, writes to (corruption) attacker-chosen kernel or other-partition memory on the thread's behalf, enabling information disclosure, memory corruption, privilege escalation, and denial of service. Affected from v3.7.0 (when Xtensa MPU userspace support was added) through v4.4.0. The fix changes the default to -EINVAL (deny by default), adds an explicit size_add_overflow check, and sets the success value only after the full range has been validated.

BT: Classic: SDP OOB access in get_att_search_list

In ascs_cp_rsp_add in /subsys/bluetooth/audio/ascs.c, an unchecked tailroom could lead to a global buffer overflow.

BT: HCI: adv_ext_report Improper discarding in adv_ext_report

No proper validation of the length of user input in olcp_ind_handler in zephyr/subsys/bluetooth/services/ots/ots_client.c.

In utf8_trunc in zephyr/lib/utils/utf8.c, last_byte_p can point to one byte before the string pointer if the string is empty.

BT: Unchecked user input in bap_broadcast_assistant

Buffer overflow in usb device class. Zephyr versions >= v2.6.0 contain Heap-based Buffer Overflow (CWE-122). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-fm6v-8625-99jf

dns_unpack_name() caches the buffer tailroom once and reuses it while appending DNS labels. As the buffer grows, the cached size becomes incorrect, and the final null terminator can be written past the buffer. With assertions disabled (default), a malicious DNS response can trigger an out-of-bounds write when CONFIG_DNS_RESOLVER is enabled.

The RNDIS USB device class includes a buffer overflow vulnerability. Zephyr versions >= v2.6.0 contain Heap-based Buffer Overflow (CWE-122). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-hvfp-w4h8-gxvj

Zephyr's IP socket recvmsg() implementation (subsys/net/lib/sockets/sockets_inet.c, insert_pktinfo()) validated the user-supplied ancillary (msg_control) buffer using only the payload length (msg->msg_controllen < pktinfo_len) before writing a full control message consisting of an aligned cmsg header plus the payload. Because the check omitted the cmsg header size, a control buffer whose length falls in the under-checked window (e.g. 16-27 bytes for IPv4 IP_PKTINFO on a 64-bit target, where a single element actually occupies 28 bytes) passes the guard yet causes a fixed-size out-of-bounds write of up to one cmsg header (~12 bytes) past the end of the buffer. Under CONFIG_USERSPACE the recvmsg verifier allocates a kernel-heap copy of the control buffer sized to msg_controllen and runs the implementation against it, so the overflow corrupts kernel heap memory and is triggerable from an unprivileged userspace thread; in supervisor mode it corrupts the caller's buffer. The path is reachable on a UDP/IP socket with IP_PKTINFO/IPV6_RECVPKTINFO (or hoplimit/timestamping) enabled when the application calls recvmsg() with an undersized control buffer and a datagram is received; part of the overwritten bytes (the destination IP in ipi_addr) is influenced by the received packet. The fix makes the capacity check use NET_CMSG_SPACE(pktinfo_len) (aligned header + aligned data) and returns -ENOMEM when the buffer is too small. Affected: v3.6.0 through v4.4.0.

In Zephyr's WireGuard subsystem (subsys/net/lib/wireguard), wg_process_data_message() in wg_crypto.c linearizes an inbound transport-data payload into a fixed pool buffer of CONFIG_WIREGUARD_BUF_LEN bytes before decryption. The call net_buf_linearize(buf->data, data_len, pkt->buffer, ..., data_len) passed the attacker-derived data_len as both the destination capacity and the copy length, defeating the function's internal len = min(len, dst_len) bound. data_len is derived from the received UDP datagram length and is only lower-bounded by wg_ctrl_recv() (no upper bound). When data_len exceeds CONFIG_WIREGUARD_BUF_LEN — e.g. when the buffer length is lowered below the link MTU, on links with MTU above the buffer size, or via reassembled IPv4/IPv6 fragments that exceed it — the underlying memcpy writes past the end of the pool buffer, an out-of-bounds write (CWE-787). The overflow occurs before the Poly1305 authentication check, so it requires only a valid receiver session index rather than a valid authenticator, and is reachable by a malicious or compromised peer (or an on-path attacker driving an established session) over the network, yielding remote memory corruption and at minimum a reliable denial of service. The defect was present in the WireGuard implementation shipped in Zephyr 4.4.0. The fix adds an explicit data_len > CONFIG_WIREGUARD_BUF_LEN rejection and corrects the linearize call to pass net_buf_max_len(buf) as the destination capacity.

The Microchip SERCOM-G1 UART driver (drivers/serial/uart_mchp_sercom_g1.c), used by the PIC32CM-JH SoC family, contains an out-of-bounds write in its asynchronous (DMA) receive path. When uart_rx_enable() is invoked with a one-byte receive buffer (len == 1) and CONFIG_UART_MCHP_ASYNC is enabled, the RX-complete ISR starts a single-beat DMA transfer while a received byte is already pending in the SERCOM DATA register. On this SoC the peripheral-triggered DMA start sequencing then writes one byte past the end of the caller-supplied buffer (CWE-787). The overflowed byte's value is the UART RX data supplied by the connected serial peer (adjacent attacker), while its size and location are fixed at one byte immediately after the buffer. Exploitation requires the async UART config (not enabled by default on the in-tree PIC32CM-JH boards) and a consumer that enables RX with a one-byte buffer; impact is limited single-byte memory corruption adjacent to the RX buffer (possible crash / denial of service). The defect shipped in v4.4.0. The fix reads the first byte with the CPU and, for one-byte buffers, performs no DMA at all; for larger buffers it sizes the DMA for the remaining len-1 bytes.

Buffer overflow in Zephyr USB DFU DNLOAD. Zephyr versions >= v2.5.0 contain Heap-based Buffer Overflow (CWE-122). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-c3gr-hgvr-f363

Stack based buffer overflow in le_ecred_conn_req(). Zephyr versions >= v2.5.0 Stack-based Buffer Overflow (CWE-121). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-8w87-6rfp-cfrm

RCE/DOS: Linked-list corruption leading to large out-of-bounds write while sorting for forged fragment list in Zephyr. Zephyr versions >= >=2.4.0 contain Out-of-bounds Write (CWE-787). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-fj4r-373f-9456

Potential buffer overflow vulnerability in the Zephyr CAN bus subsystem

In gnss service, there is a possible out of bounds write due to an incorrect bounds check. This could lead to local escalation of privilege if a malicious actor has already obtained the System privilege. User interaction is not needed for exploitation. Patch ID: ALPS10010441; Issue ID: MSV-3967.

The nRF70 Wi-Fi driver's power-save event handler nrf_wifi_event_proc_get_power_save_info() in drivers/wifi/nrf_wifi/src/wifi_mgmt.c copied TWT (Target Wake Time) flow entries from an nrf_wifi_umac_event_power_save_info event into the fixed-size twt_flows[WIFI_MAX_TWT_FLOWS] (8-element) array of a caller-supplied struct wifi_ps_config, looping over event-provided num_twt_flows without validating it against WIFI_MAX_TWT_FLOWS or checking event_len. When num_twt_flows exceeds 8, the handler writes past the destination array (which is typically on the caller's stack, e.g. the wifi ps shell command) -- an out-of-bounds write of ~40-byte TWT entries -- and reads twt_flow_info[i] past the event buffer. The event is delivered by the nRF70 co-processor firmware in response to a host-initiated power-save GET, so reaching the overflow requires the firmware to emit a malformed or out-of-range event; the trust boundary is host-to-trusted-coprocessor rather than a direct remote-AP write, with over-the-air influence on the flow count being indirect and bounded by the 3-bit TWT flow-id space. Affected: builds with CONFIG_NRF70_STA_MODE on releases through v4.4.0. The fix rejects events with num_twt_flows > WIFI_MAX_TWT_FLOWS or with event_len shorter than the claimed entries, and adds a NULL check on the caller buffer.

The Zephyr ADIN2111/ADIN1110 10BASE-T1S/T1L Ethernet driver (drivers/ethernet/eth_adin2111.c) reassembles received Ethernet frames in OPEN Alliance (OA) SPI mode by copying device-supplied 64-byte data chunks into a fixed static buffer ctx->buf of size CONFIG_ETH_ADIN2111_BUFFER_SIZE (default 1524 bytes). In eth_adin2111_oa_data_read(), each valid chunk was memcpy'd into ctx->buf[ctx->scur] and the write cursor scur advanced, with no check that scur + len stayed within the buffer. The number of chunks (up to 255, from the BUFSTS RCA field) and the per-chunk length are taken entirely from the frame data received off the wire; the cursor is only reset on a start-of-frame chunk. An attacker on the single-pair Ethernet segment can therefore send a frame whose reassembled size exceeds the configured buffer, causing the driver's RX offload thread to write attacker-controlled frame bytes past the end of the static buffer into adjacent driver/kernel memory (up to roughly 14.8 KB in the worst case). This is a remotely/adjacently reachable out-of-bounds write (CWE-787) that can corrupt memory and cause denial of service or potentially code execution. The defect was introduced when OA SPI support was added (commit 0ca8b0756b1) and shipped in releases v3.7.0 through v4.4.0. The fix adds a bounds check that drops the oversized frame and resets the cursor before the copy.

Malformed SPI in response for eswifi can corrupt kernel memory. Zephyr versions >= 1.14.2, >= 2.3.0 contain Heap-based Buffer Overflow (CWE-122). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-hx4p-j86p-2mhr

The Bluetooth BAP Broadcast Assistant GATT client in subsys/bluetooth/audio/bap_broadcast_assistant.c reassembled remote Broadcast Receive State data into a single file-static net_buf_simple (att_buf, BT_ATT_MAX_ATTRIBUTE_LEN = 512 bytes) shared by all connection instances, while the BUSY flag, long-read handle, and reset/offset state were per-connection. When the device acts as a Broadcast Assistant connected to multiple Scan Delegator peripherals, notification and long-read callbacks from different connections interleave on the shared buffer: the append in notify_handler (net_buf_simple_add_mem at the not-busy branch) performs no tailroom check, so receive-state notifications from two or more delegators accumulate on the same 512-byte buffer and, with a sufficiently large configured ATT MTU (BT_L2CAP_TX_MTU up to 2000) and two-to-three concurrent connections, write past the buffer into adjacent .bss (net_buf_simple_add only asserts in debug builds). Even below the overflow threshold, one connection's net_buf_simple_reset zeroes the shared length while another connection's reassembly and GATT read offset are in flight, mixing one peer's data into another's parse. A malicious or compromised Scan Delegator (or two colluding peers) over BLE can trigger this, causing out-of-bounds writes (memory corruption / denial of service) and cross-connection data corruption. The fix moves the buffer into the per-connection instance struct so each connection reassembles into its own buffer. Affects Zephyr releases shipping the Broadcast Assistant with the shared buffer, including v4.4.0 and earlier.

FS: Buffer Overflow when enabling Long File Names in FAT_FS and calling fs_stat. Zephyr versions >= v1.14.2, >= v2.3.0 contain Stack-based Buffer Overflow (CWE-121). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-7fhv-rgxr-x56h

Missing Size Checks in Bluetooth HCI over SPI. Zephyr versions >= v1.14.2, >= v2.2.0 contain Improper Handling of Length Parameter Inconsistency (CWE-130). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-hg2w-62p6-g67c

Out-of-bounds Write in the USB Mass Storage memoryWrite handler with unaligned Sizes See NCC-ZEP-024, NCC-ZEP-025, NCC-ZEP-026 This issue affects: zephyrproject-rtos zephyr version 1.14.1 and later versions. version 2.1.0 and later versions.

Improper handling of the full-buffer case in the Zephyr Bluetooth implementation can result in memory corruption. This issue affects: zephyrproject-rtos zephyr version 2.2.0 and later versions, and version 1.14.0 and later versions.

Improper Input Frame Validation in ieee802154 Processing. Zephyr versions >= v1.14.2, >= v2.2.0 contain Stack-based Buffer Overflow (CWE-121), Heap-based Buffer Overflow (CWE-122). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-3gvq-h42f-v3c7

Out-of-bounds read, Out-of-bounds write vulnerability in Samsung Open Source Escargot allows Overflow Buffers. This issue affects Escargot: before 779f6bedf58f334dec64b0a51ebb724b4708b84a.

Access of uninitialized pointer, Uncontrolled Recursion vulnerability in Samsung Open Source rlottie allows Pointer Manipulation, Oversized Serialized Data Payloads. This issue affects rlottie: before eae37633fda13ac05b25c6c95aacea4bc33c80a3.

Uncontrolled Recursion vulnerability in Samsung Open Source rlottie allows Oversized Serialized Data Payloads. This issue affects rlottie: before e2d19e3b150e0e4a9586fa90b56fd3061cc98945.

OpenEXR is the reference implementation and specification for the EXR image format, widely used in the motion picture industry. In versions 3.4.0 through 3.4.11, an integer overflow in ht_undo_impl() in src/lib/OpenEXRCore/internal_ht.cpp leads to a heap-buffer overflow when decoding a crafted HTJ2K-compressed EXR file. decode->channels[i].width (int32_t) is multiplied by bytes_per_element in 32-bit signed arithmetic. With large widths (e.g., >= 536870912 for FLOAT data), this overflows, producing a corrupted offset that is later used for pointer arithmetic and can cause a heap out-of-bounds write. The same unchecked multiplication pattern appears in two other HTJ2K paths (bytes-per-line accumulation and pixel-line pointer advancement). As with related CVE-2026-34378 through CVE-2026-34589 fixes in other codecs, validating only after the multiplication is too late because the value may already be overflowed. This issue has been fixed in version 3.4.12.

A flaw was found in GIMP. This vulnerability, a buffer overflow in the `file-seattle-filmworks` plugin, can be exploited when a user opens a specially crafted Seattle Filmworks file. A remote attacker could leverage this to cause a denial of service (DoS), leading to the plugin crashing and potentially impacting the stability of the GIMP application.

Acrobat Reader DC versions 2021.005.20060 (and earlier), 2020.004.30006 (and earlier) and 2017.011.30199 (and earlier) are affected by a stack overflow vulnerability due to insecure handling of a crafted PDF file, potentially resulting in memory corruption in the context of the current user. Exploitation requires user interaction in that a victim must open a crafted PDF file in Acrobat Reader.

Acrobat Reader DC versions 2021.005.20060 (and earlier), 2020.004.30006 (and earlier) and 2017.011.30199 (and earlier) are affected by a stack overflow vulnerability due to insecure handling of a crafted PDF file, potentially resulting in memory corruption in the context of the current user. Exploitation requires user interaction in that a victim must open a crafted PDF file in Acrobat Reader.