In the Linux kernel, the following vulnerability has been resolved: KVM: nSVM: Ignore nCR3[4:0] when loading PDPTEs from memory Ignore nCR3[4:0] when loading PDPTEs from memory for nested SVM, as bits 4:0 of CR3 are ignored when PAE paging is used, and thus VMRUN doesn't enforce 32-byte alignment of nCR3. In the absolute worst case scenario, failure to ignore bits 4:0 can result in an out-of-bounds read, e.g. if the target page is at the end of a memslot, and the VMM isn't using guard pages. Per the APM: The CR3 register points to the base address of the page-directory-pointer table. The page-directory-pointer table is aligned on a 32-byte boundary, with the low 5 address bits 4:0 assumed to be 0. And the SDM's much more explicit: 4:0 Ignored Note, KVM gets this right when loading PDPTRs, it's only the nSVM flow that is broken.

In the Linux kernel, the following vulnerability has been resolved: RDMA/bnxt_re: Fix out of bound check Driver exports pacing stats only on GenP5 and P7 adapters. But while parsing the pacing stats, driver has a check for "rdev->dbr_pacing". This caused a trace when KASAN is enabled. BUG: KASAN: slab-out-of-bounds in bnxt_re_get_hw_stats+0x2b6a/0x2e00 [bnxt_re] Write of size 8 at addr ffff8885942a6340 by task modprobe/4809

In the Linux kernel, the following vulnerability has been resolved: parport: Proper fix for array out-of-bounds access The recent fix for array out-of-bounds accesses replaced sprintf() calls blindly with snprintf(). However, since snprintf() returns the would-be-printed size, not the actually output size, the length calculation can still go over the given limit. Use scnprintf() instead of snprintf(), which returns the actually output letters, for addressing the potential out-of-bounds access properly.

In the Linux kernel, the following vulnerability has been resolved: netdevsim: Add trailing zero to terminate the string in nsim_nexthop_bucket_activity_write() This was found by a static analyzer. We should not forget the trailing zero after copy_from_user() if we will further do some string operations, sscanf() in this case. Adding a trailing zero will ensure that the function performs properly.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Correct tid cleanup when tid setup fails Currently, if any error occurs during ath12k_dp_rx_peer_tid_setup(), the tid value is already incremented, even though the corresponding TID is not actually allocated. Proceed to ath12k_dp_rx_peer_tid_delete() starting from unallocated tid, which might leads to freeing unallocated TID and cause potential crash or out-of-bounds access. Hence, fix by correctly decrementing tid before cleanup to match only the successfully allocated TIDs. Also, remove tid-- from failure case of ath12k_dp_rx_peer_frag_setup(), as decrementing the tid before cleanup in loop will take care of this. Compile tested only.

In the Linux kernel, the following vulnerability has been resolved: netfilter: x_tables: fix LED ID check in led_tg_check() Syzbot has reported the following BUG detected by KASAN: BUG: KASAN: slab-out-of-bounds in strlen+0x58/0x70 Read of size 1 at addr ffff8881022da0c8 by task repro/5879 ... Call Trace: <TASK> dump_stack_lvl+0x241/0x360 ? __pfx_dump_stack_lvl+0x10/0x10 ? __pfx__printk+0x10/0x10 ? _printk+0xd5/0x120 ? __virt_addr_valid+0x183/0x530 ? __virt_addr_valid+0x183/0x530 print_report+0x169/0x550 ? __virt_addr_valid+0x183/0x530 ? __virt_addr_valid+0x183/0x530 ? __virt_addr_valid+0x45f/0x530 ? __phys_addr+0xba/0x170 ? strlen+0x58/0x70 kasan_report+0x143/0x180 ? strlen+0x58/0x70 strlen+0x58/0x70 kstrdup+0x20/0x80 led_tg_check+0x18b/0x3c0 xt_check_target+0x3bb/0xa40 ? __pfx_xt_check_target+0x10/0x10 ? stack_depot_save_flags+0x6e4/0x830 ? nft_target_init+0x174/0xc30 nft_target_init+0x82d/0xc30 ? __pfx_nft_target_init+0x10/0x10 ? nf_tables_newrule+0x1609/0x2980 ? nf_tables_newrule+0x1609/0x2980 ? rcu_is_watching+0x15/0xb0 ? nf_tables_newrule+0x1609/0x2980 ? nf_tables_newrule+0x1609/0x2980 ? __kmalloc_noprof+0x21a/0x400 nf_tables_newrule+0x1860/0x2980 ? __pfx_nf_tables_newrule+0x10/0x10 ? __nla_parse+0x40/0x60 nfnetlink_rcv+0x14e5/0x2ab0 ? __pfx_validate_chain+0x10/0x10 ? __pfx_nfnetlink_rcv+0x10/0x10 ? __lock_acquire+0x1384/0x2050 ? netlink_deliver_tap+0x2e/0x1b0 ? __pfx_lock_release+0x10/0x10 ? netlink_deliver_tap+0x2e/0x1b0 netlink_unicast+0x7f8/0x990 ? __pfx_netlink_unicast+0x10/0x10 ? __virt_addr_valid+0x183/0x530 ? __check_object_size+0x48e/0x900 netlink_sendmsg+0x8e4/0xcb0 ? __pfx_netlink_sendmsg+0x10/0x10 ? aa_sock_msg_perm+0x91/0x160 ? __pfx_netlink_sendmsg+0x10/0x10 __sock_sendmsg+0x223/0x270 ____sys_sendmsg+0x52a/0x7e0 ? __pfx_____sys_sendmsg+0x10/0x10 __sys_sendmsg+0x292/0x380 ? __pfx___sys_sendmsg+0x10/0x10 ? lockdep_hardirqs_on_prepare+0x43d/0x780 ? __pfx_lockdep_hardirqs_on_prepare+0x10/0x10 ? exc_page_fault+0x590/0x8c0 ? do_syscall_64+0xb6/0x230 do_syscall_64+0xf3/0x230 entry_SYSCALL_64_after_hwframe+0x77/0x7f ... </TASK> Since an invalid (without '\0' byte at all) byte sequence may be passed from userspace, add an extra check to ensure that such a sequence is rejected as possible ID and so never passed to 'kstrdup()' and further.

Out of bounds read in DevTools in Google Chrome prior to 149.0.7827.53 allowed a remote attacker to execute arbitrary code inside a sandbox via a crafted HTML page. (Chromium security severity: Low)

Bad cast in Dawn in Google Chrome prior to 149.0.7827.53 allowed a remote attacker to execute arbitrary code inside a sandbox via a crafted HTML page. (Chromium security severity: Medium)

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: mcc: prevent shift wrapping in rtw89_core_mlsr_switch() The "link_id" value comes from the user via debugfs. If it's larger than BITS_PER_LONG then that would result in shift wrapping and potentially an out of bounds access later. In fact, we can limit it to IEEE80211_MLD_MAX_NUM_LINKS (15). Fortunately, only root can write to debugfs files so the security impact is minimal.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix OOB read when checking dotdot dir Mounting a corrupted filesystem with directory which contains '.' dir entry with rec_len == block size results in out-of-bounds read (later on, when the corrupted directory is removed). ext4_empty_dir() assumes every ext4 directory contains at least '.' and '..' as directory entries in the first data block. It first loads the '.' dir entry, performs sanity checks by calling ext4_check_dir_entry() and then uses its rec_len member to compute the location of '..' dir entry (in ext4_next_entry). It assumes the '..' dir entry fits into the same data block. If the rec_len of '.' is precisely one block (4KB), it slips through the sanity checks (it is considered the last directory entry in the data block) and leaves "struct ext4_dir_entry_2 *de" point exactly past the memory slot allocated to the data block. The following call to ext4_check_dir_entry() on new value of de then dereferences this pointer which results in out-of-bounds mem access. Fix this by extending __ext4_check_dir_entry() to check for '.' dir entries that reach the end of data block. Make sure to ignore the phony dir entries for checksum (by checking name_len for non-zero). Note: This is reported by KASAN as use-after-free in case another structure was recently freed from the slot past the bound, but it is really an OOB read. This issue was found by syzkaller tool. Call Trace: [ 38.594108] BUG: KASAN: slab-use-after-free in __ext4_check_dir_entry+0x67e/0x710 [ 38.594649] Read of size 2 at addr ffff88802b41a004 by task syz-executor/5375 [ 38.595158] [ 38.595288] CPU: 0 UID: 0 PID: 5375 Comm: syz-executor Not tainted 6.14.0-rc7 #1 [ 38.595298] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 [ 38.595304] Call Trace: [ 38.595308] <TASK> [ 38.595311] dump_stack_lvl+0xa7/0xd0 [ 38.595325] print_address_description.constprop.0+0x2c/0x3f0 [ 38.595339] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595349] print_report+0xaa/0x250 [ 38.595359] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595368] ? kasan_addr_to_slab+0x9/0x90 [ 38.595378] kasan_report+0xab/0xe0 [ 38.595389] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595400] __ext4_check_dir_entry+0x67e/0x710 [ 38.595410] ext4_empty_dir+0x465/0x990 [ 38.595421] ? __pfx_ext4_empty_dir+0x10/0x10 [ 38.595432] ext4_rmdir.part.0+0x29a/0xd10 [ 38.595441] ? __dquot_initialize+0x2a7/0xbf0 [ 38.595455] ? __pfx_ext4_rmdir.part.0+0x10/0x10 [ 38.595464] ? __pfx___dquot_initialize+0x10/0x10 [ 38.595478] ? down_write+0xdb/0x140 [ 38.595487] ? __pfx_down_write+0x10/0x10 [ 38.595497] ext4_rmdir+0xee/0x140 [ 38.595506] vfs_rmdir+0x209/0x670 [ 38.595517] ? lookup_one_qstr_excl+0x3b/0x190 [ 38.595529] do_rmdir+0x363/0x3c0 [ 38.595537] ? __pfx_do_rmdir+0x10/0x10 [ 38.595544] ? strncpy_from_user+0x1ff/0x2e0 [ 38.595561] __x64_sys_unlinkat+0xf0/0x130 [ 38.595570] do_syscall_64+0x5b/0x180 [ 38.595583] entry_SYSCALL_64_after_hwframe+0x76/0x7e

In the Linux kernel, the following vulnerability has been resolved: of/irq: Prevent device address out-of-bounds read in interrupt map walk When of_irq_parse_raw() is invoked with a device address smaller than the interrupt parent node (from #address-cells property), KASAN detects the following out-of-bounds read when populating the initial match table (dyndbg="func of_irq_parse_* +p"): OF: of_irq_parse_one: dev=/soc@0/picasso/watchdog, index=0 OF: parent=/soc@0/pci@878000000000/gpio0@17,0, intsize=2 OF: intspec=4 OF: of_irq_parse_raw: ipar=/soc@0/pci@878000000000/gpio0@17,0, size=2 OF: -> addrsize=3 ================================================================== BUG: KASAN: slab-out-of-bounds in of_irq_parse_raw+0x2b8/0x8d0 Read of size 4 at addr ffffff81beca5608 by task bash/764 CPU: 1 PID: 764 Comm: bash Tainted: G O 6.1.67-484c613561-nokia_sm_arm64 #1 Hardware name: Unknown Unknown Product/Unknown Product, BIOS 2023.01-12.24.03-dirty 01/01/2023 Call trace: dump_backtrace+0xdc/0x130 show_stack+0x1c/0x30 dump_stack_lvl+0x6c/0x84 print_report+0x150/0x448 kasan_report+0x98/0x140 __asan_load4+0x78/0xa0 of_irq_parse_raw+0x2b8/0x8d0 of_irq_parse_one+0x24c/0x270 parse_interrupts+0xc0/0x120 of_fwnode_add_links+0x100/0x2d0 fw_devlink_parse_fwtree+0x64/0xc0 device_add+0xb38/0xc30 of_device_add+0x64/0x90 of_platform_device_create_pdata+0xd0/0x170 of_platform_bus_create+0x244/0x600 of_platform_notify+0x1b0/0x254 blocking_notifier_call_chain+0x9c/0xd0 __of_changeset_entry_notify+0x1b8/0x230 __of_changeset_apply_notify+0x54/0xe4 of_overlay_fdt_apply+0xc04/0xd94 ... The buggy address belongs to the object at ffffff81beca5600 which belongs to the cache kmalloc-128 of size 128 The buggy address is located 8 bytes inside of 128-byte region [ffffff81beca5600, ffffff81beca5680) The buggy address belongs to the physical page: page:00000000230d3d03 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1beca4 head:00000000230d3d03 order:1 compound_mapcount:0 compound_pincount:0 flags: 0x8000000000010200(slab|head|zone=2) raw: 8000000000010200 0000000000000000 dead000000000122 ffffff810000c300 raw: 0000000000000000 0000000000200020 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffffff81beca5500: 04 fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffffff81beca5580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffffff81beca5600: 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffffff81beca5680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffffff81beca5700: 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc ================================================================== OF: -> got it ! Prevent the out-of-bounds read by copying the device address into a buffer of sufficient size.

In the Linux kernel, the following vulnerability has been resolved: HID: cougar: fix slab-out-of-bounds Read in cougar_report_fixup report_fixup for the Cougar 500k Gaming Keyboard was not verifying that the report descriptor size was correct before accessing it

In the Linux kernel, the following vulnerability has been resolved: bpf: add check for invalid name in btf_name_valid_section() If the length of the name string is 1 and the value of name[0] is NULL byte, an OOB vulnerability occurs in btf_name_valid_section() and the return value is true, so the invalid name passes the check. To solve this, you need to check if the first position is NULL byte and if the first character is printable.

In the Linux kernel, the following vulnerability has been resolved: jfs: fix out-of-bounds in dbNextAG() and diAlloc() In dbNextAG() , there is no check for the case where bmp->db_numag is greater or same than MAXAG due to a polluted image, which causes an out-of-bounds. Therefore, a bounds check should be added in dbMount(). And in dbNextAG(), a check for the case where agpref is greater than bmp->db_numag should be added, so an out-of-bounds exception should be prevented. Additionally, a check for the case where agno is greater or same than MAXAG should be added in diAlloc() to prevent out-of-bounds.

The Linux kernel was found vulnerable out of bounds memory access in the drivers/video/fbdev/sm712fb.c:smtcfb_read() function. The vulnerability could result in local attackers being able to crash the kernel.

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix potential oob read in nilfs_btree_check_delete() The function nilfs_btree_check_delete(), which checks whether degeneration to direct mapping occurs before deleting a b-tree entry, causes memory access outside the block buffer when retrieving the maximum key if the root node has no entries. This does not usually happen because b-tree mappings with 0 child nodes are never created by mkfs.nilfs2 or nilfs2 itself. However, it can happen if the b-tree root node read from a device is configured that way, so fix this potential issue by adding a check for that case.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/pm: fix the Out-of-bounds read warning using index i - 1U may beyond element index for mc_data[] when i = 0.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix ucode out-of-bounds read warning Clear warning that read ucode[] may out-of-bounds.

An issue was discovered in the Linux kernel before 4.20.2. An out-of-bounds access exists in the function build_audio_procunit in the file sound/usb/mixer.c.

An issue was discovered in the Linux kernel before 5.0.10. SMB2_negotiate in fs/cifs/smb2pdu.c has an out-of-bounds read because data structures are incompletely updated after a change from smb30 to smb21.

In the Linux kernel, the following vulnerability has been resolved: xfrm: Fix input error path memory access When there is a misconfiguration of input state slow path KASAN report error. Fix this error. west login: [ 52.987278] eth1: renamed from veth11 [ 53.078814] eth1: renamed from veth21 [ 53.181355] eth1: renamed from veth31 [ 54.921702] ================================================================== [ 54.922602] BUG: KASAN: wild-memory-access in xfrmi_rcv_cb+0x2d/0x295 [ 54.923393] Read of size 8 at addr 6b6b6b6b00000000 by task ping/512 [ 54.924169] [ 54.924386] CPU: 0 PID: 512 Comm: ping Not tainted 6.9.0-08574-gcd29a4313a1b #25 [ 54.925290] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 54.926401] Call Trace: [ 54.926731] <IRQ> [ 54.927009] dump_stack_lvl+0x2a/0x3b [ 54.927478] kasan_report+0x84/0xa6 [ 54.927930] ? xfrmi_rcv_cb+0x2d/0x295 [ 54.928410] xfrmi_rcv_cb+0x2d/0x295 [ 54.928872] ? xfrm4_rcv_cb+0x3d/0x5e [ 54.929354] xfrm4_rcv_cb+0x46/0x5e [ 54.929804] xfrm_rcv_cb+0x7e/0xa1 [ 54.930240] xfrm_input+0x1b3a/0x1b96 [ 54.930715] ? xfrm_offload+0x41/0x41 [ 54.931182] ? raw_rcv+0x292/0x292 [ 54.931617] ? nf_conntrack_confirm+0xa2/0xa2 [ 54.932158] ? skb_sec_path+0xd/0x3f [ 54.932610] ? xfrmi_input+0x90/0xce [ 54.933066] xfrm4_esp_rcv+0x33/0x54 [ 54.933521] ip_protocol_deliver_rcu+0xd7/0x1b2 [ 54.934089] ip_local_deliver_finish+0x110/0x120 [ 54.934659] ? ip_protocol_deliver_rcu+0x1b2/0x1b2 [ 54.935248] NF_HOOK.constprop.0+0xf8/0x138 [ 54.935767] ? ip_sublist_rcv_finish+0x68/0x68 [ 54.936317] ? secure_tcpv6_ts_off+0x23/0x168 [ 54.936859] ? ip_protocol_deliver_rcu+0x1b2/0x1b2 [ 54.937454] ? __xfrm_policy_check2.constprop.0+0x18d/0x18d [ 54.938135] NF_HOOK.constprop.0+0xf8/0x138 [ 54.938663] ? ip_sublist_rcv_finish+0x68/0x68 [ 54.939220] ? __xfrm_policy_check2.constprop.0+0x18d/0x18d [ 54.939904] ? ip_local_deliver_finish+0x120/0x120 [ 54.940497] __netif_receive_skb_one_core+0xc9/0x107 [ 54.941121] ? __netif_receive_skb_list_core+0x1c2/0x1c2 [ 54.941771] ? blk_mq_start_stopped_hw_queues+0xc7/0xf9 [ 54.942413] ? blk_mq_start_stopped_hw_queue+0x38/0x38 [ 54.943044] ? virtqueue_get_buf_ctx+0x295/0x46b [ 54.943618] process_backlog+0xb3/0x187 [ 54.944102] __napi_poll.constprop.0+0x57/0x1a7 [ 54.944669] net_rx_action+0x1cb/0x380 [ 54.945150] ? __napi_poll.constprop.0+0x1a7/0x1a7 [ 54.945744] ? vring_new_virtqueue+0x17a/0x17a [ 54.946300] ? note_interrupt+0x2cd/0x367 [ 54.946805] handle_softirqs+0x13c/0x2c9 [ 54.947300] do_softirq+0x5f/0x7d [ 54.947727] </IRQ> [ 54.948014] <TASK> [ 54.948300] __local_bh_enable_ip+0x48/0x62 [ 54.948832] __neigh_event_send+0x3fd/0x4ca [ 54.949361] neigh_resolve_output+0x1e/0x210 [ 54.949896] ip_finish_output2+0x4bf/0x4f0 [ 54.950410] ? __ip_finish_output+0x171/0x1b8 [ 54.950956] ip_send_skb+0x25/0x57 [ 54.951390] raw_sendmsg+0xf95/0x10c0 [ 54.951850] ? check_new_pages+0x45/0x71 [ 54.952343] ? raw_hash_sk+0x21b/0x21b [ 54.952815] ? kernel_init_pages+0x42/0x51 [ 54.953337] ? prep_new_page+0x44/0x51 [ 54.953811] ? get_page_from_freelist+0x72b/0x915 [ 54.954390] ? signal_pending_state+0x77/0x77 [ 54.954936] ? preempt_count_sub+0x14/0xb3 [ 54.955450] ? __might_resched+0x8a/0x240 [ 54.955951] ? __might_sleep+0x25/0xa0 [ 54.956424] ? first_zones_zonelist+0x2c/0x43 [ 54.956977] ? __rcu_read_lock+0x2d/0x3a [ 54.957476] ? __pte_offset_map+0x32/0xa4 [ 54.957980] ? __might_resched+0x8a/0x240 [ 54.958483] ? __might_sleep+0x25/0xa0 [ 54.958963] ? inet_send_prepare+0x54/0x54 [ 54.959478] ? sock_sendmsg_nosec+0x42/0x6c [ 54.960000] sock_sendmsg_nosec+0x42/0x6c [ 54.960502] __sys_sendto+0x15d/0x1cc [ 54.960966] ? __x64_sys_getpeername+0x44/0x44 [ 54.961522] ? __handle_mm_fault+0x679/0xae4 [ 54.962068] ? find_vma+0x6b/0x ---truncated---

An issue was discovered in the Linux kernel before 5.0.19. There is an out-of-bounds array access in __xfrm_policy_unlink, which will cause denial of service, because verify_newpolicy_info in net/xfrm/xfrm_user.c mishandles directory validation.

In the Linux kernel, the following vulnerability has been resolved: media: adv7842: Avoid possible out-of-bounds array accesses in adv7842_cp_log_status() It's possible for cp_read() and hdmi_read() to return -EIO. Those values are further used as indexes for accessing arrays. Fix that by checking return values where it's needed. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Adjust VSDB parser for replay feature At some point, the IEEE ID identification for the replay check in the AMD EDID was added. However, this check causes the following out-of-bounds issues when using KASAN: [ 27.804016] BUG: KASAN: slab-out-of-bounds in amdgpu_dm_update_freesync_caps+0xefa/0x17a0 [amdgpu] [ 27.804788] Read of size 1 at addr ffff8881647fdb00 by task systemd-udevd/383 ... [ 27.821207] Memory state around the buggy address: [ 27.821215] ffff8881647fda00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 27.821224] ffff8881647fda80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 27.821234] >ffff8881647fdb00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 27.821243] ^ [ 27.821250] ffff8881647fdb80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 27.821259] ffff8881647fdc00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 27.821268] ================================================================== This is caused because the ID extraction happens outside of the range of the edid lenght. This commit addresses this issue by considering the amd_vsdb_block size. (cherry picked from commit b7e381b1ccd5e778e3d9c44c669ad38439a861d8)

In the Linux kernel before 5.2.3, set_geometry in drivers/block/floppy.c does not validate the sect and head fields, as demonstrated by an integer overflow and out-of-bounds read. It can be triggered by an unprivileged local user when a floppy disk has been inserted. NOTE: QEMU creates the floppy device by default.

In the Linux kernel, the following vulnerability has been resolved: kobject_uevent: Fix OOB access within zap_modalias_env() zap_modalias_env() wrongly calculates size of memory block to move, so will cause OOB memory access issue if variable MODALIAS is not the last one within its @env parameter, fixed by correcting size to memmove.

In the Linux kernel, the following vulnerability has been resolved: xfs: add bounds checking to xlog_recover_process_data There is a lack of verification of the space occupied by fixed members of xlog_op_header in the xlog_recover_process_data. We can create a crafted image to trigger an out of bounds read by following these steps: 1) Mount an image of xfs, and do some file operations to leave records 2) Before umounting, copy the image for subsequent steps to simulate abnormal exit. Because umount will ensure that tail_blk and head_blk are the same, which will result in the inability to enter xlog_recover_process_data 3) Write a tool to parse and modify the copied image in step 2 4) Make the end of the xlog_op_header entries only 1 byte away from xlog_rec_header->h_size 5) xlog_rec_header->h_num_logops++ 6) Modify xlog_rec_header->h_crc Fix: Add a check to make sure there is sufficient space to access fixed members of xlog_op_header.

vcs_write in drivers/tty/vt/vc_screen.c in the Linux kernel through 5.3.13 does not prevent write access to vcsu devices, aka CID-0c9acb1af77a.

In the Linux kernel, the following vulnerability has been resolved: bonding: Fix out-of-bounds read in bond_option_arp_ip_targets_set() In function bond_option_arp_ip_targets_set(), if newval->string is an empty string, newval->string+1 will point to the byte after the string, causing an out-of-bound read. BUG: KASAN: slab-out-of-bounds in strlen+0x7d/0xa0 lib/string.c:418 Read of size 1 at addr ffff8881119c4781 by task syz-executor665/8107 CPU: 1 PID: 8107 Comm: syz-executor665 Not tainted 6.7.0-rc7 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xd9/0x150 lib/dump_stack.c:106 print_address_description mm/kasan/report.c:364 [inline] print_report+0xc1/0x5e0 mm/kasan/report.c:475 kasan_report+0xbe/0xf0 mm/kasan/report.c:588 strlen+0x7d/0xa0 lib/string.c:418 __fortify_strlen include/linux/fortify-string.h:210 [inline] in4_pton+0xa3/0x3f0 net/core/utils.c:130 bond_option_arp_ip_targets_set+0xc2/0x910 drivers/net/bonding/bond_options.c:1201 __bond_opt_set+0x2a4/0x1030 drivers/net/bonding/bond_options.c:767 __bond_opt_set_notify+0x48/0x150 drivers/net/bonding/bond_options.c:792 bond_opt_tryset_rtnl+0xda/0x160 drivers/net/bonding/bond_options.c:817 bonding_sysfs_store_option+0xa1/0x120 drivers/net/bonding/bond_sysfs.c:156 dev_attr_store+0x54/0x80 drivers/base/core.c:2366 sysfs_kf_write+0x114/0x170 fs/sysfs/file.c:136 kernfs_fop_write_iter+0x337/0x500 fs/kernfs/file.c:334 call_write_iter include/linux/fs.h:2020 [inline] new_sync_write fs/read_write.c:491 [inline] vfs_write+0x96a/0xd80 fs/read_write.c:584 ksys_write+0x122/0x250 fs/read_write.c:637 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x40/0x110 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b ---[ end trace ]--- Fix it by adding a check of string length before using it.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: add error handle to avoid out-of-bounds if the sdma_v4_0_irq_id_to_seq return -EINVAL, the process should be stop to avoid out-of-bounds read, so directly return -EINVAL.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to do sanity check on i_xattr_nid in sanity_check_inode() syzbot reports a kernel bug as below: F2FS-fs (loop0): Mounted with checkpoint version = 48b305e4 ================================================================== BUG: KASAN: slab-out-of-bounds in f2fs_test_bit fs/f2fs/f2fs.h:2933 [inline] BUG: KASAN: slab-out-of-bounds in current_nat_addr fs/f2fs/node.h:213 [inline] BUG: KASAN: slab-out-of-bounds in f2fs_get_node_info+0xece/0x1200 fs/f2fs/node.c:600 Read of size 1 at addr ffff88807a58c76c by task syz-executor280/5076 CPU: 1 PID: 5076 Comm: syz-executor280 Not tainted 6.9.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114 print_address_description mm/kasan/report.c:377 [inline] print_report+0x169/0x550 mm/kasan/report.c:488 kasan_report+0x143/0x180 mm/kasan/report.c:601 f2fs_test_bit fs/f2fs/f2fs.h:2933 [inline] current_nat_addr fs/f2fs/node.h:213 [inline] f2fs_get_node_info+0xece/0x1200 fs/f2fs/node.c:600 f2fs_xattr_fiemap fs/f2fs/data.c:1848 [inline] f2fs_fiemap+0x55d/0x1ee0 fs/f2fs/data.c:1925 ioctl_fiemap fs/ioctl.c:220 [inline] do_vfs_ioctl+0x1c07/0x2e50 fs/ioctl.c:838 __do_sys_ioctl fs/ioctl.c:902 [inline] __se_sys_ioctl+0x81/0x170 fs/ioctl.c:890 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f The root cause is we missed to do sanity check on i_xattr_nid during f2fs_iget(), so that in fiemap() path, current_nat_addr() will access nat_bitmap w/ offset from invalid i_xattr_nid, result in triggering kasan bug report, fix it.

In the Linux kernel, the following vulnerability has been resolved: soundwire: cadence: fix invalid PDI offset For some reason, we add an offset to the PDI, presumably to skip the PDI0 and PDI1 which are reserved for BPT. This code is however completely wrong and leads to an out-of-bounds access. We were just lucky so far since we used only a couple of PDIs and remained within the PDI array bounds. A Fixes: tag is not provided since there are no known platforms where the out-of-bounds would be accessed, and the initial code had problems as well. A follow-up patch completely removes this useless offset.

In the Linux kernel, the following vulnerability has been resolved: crypto: qat - validate slices count returned by FW The function adf_send_admin_tl_start() enables the telemetry (TL) feature on a QAT device by sending the ICP_QAT_FW_TL_START message to the firmware. This triggers the FW to start writing TL data to a DMA buffer in memory and returns an array containing the number of accelerators of each type (slices) supported by this HW. The pointer to this array is stored in the adf_tl_hw_data data structure called slice_cnt. The array slice_cnt is then used in the function tl_print_dev_data() to report in debugfs only statistics about the supported accelerators. An incorrect value of the elements in slice_cnt might lead to an out of bounds memory read. At the moment, there isn't an implementation of FW that returns a wrong value, but for robustness validate the slice count array returned by FW.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix out-of-bound access of qmi_invoke_handler() Currently, there is no terminator entry for ath12k_qmi_msg_handlers hence facing below KASAN warning, ================================================================== BUG: KASAN: global-out-of-bounds in qmi_invoke_handler+0xa4/0x148 Read of size 8 at addr ffffffd00a6428d8 by task kworker/u8:2/1273 CPU: 0 PID: 1273 Comm: kworker/u8:2 Not tainted 5.4.213 #0 Workqueue: qmi_msg_handler qmi_data_ready_work Call trace: dump_backtrace+0x0/0x20c show_stack+0x14/0x1c dump_stack+0xe0/0x138 print_address_description.isra.5+0x30/0x330 __kasan_report+0x16c/0x1bc kasan_report+0xc/0x14 __asan_load8+0xa8/0xb0 qmi_invoke_handler+0xa4/0x148 qmi_handle_message+0x18c/0x1bc qmi_data_ready_work+0x4ec/0x528 process_one_work+0x2c0/0x440 worker_thread+0x324/0x4b8 kthread+0x210/0x228 ret_from_fork+0x10/0x18 The address belongs to the variable: ath12k_mac_mon_status_filter_default+0x4bd8/0xfffffffffffe2300 [ath12k] [...] ================================================================== Add a dummy terminator entry at the end to assist the qmi_invoke_handler() in traversing up to the terminator entry without accessing an out-of-boundary index. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

In the Linux kernel, the following vulnerability has been resolved: scsi: bfa: Ensure the copied buf is NUL terminated Currently, we allocate a nbytes-sized kernel buffer and copy nbytes from userspace to that buffer. Later, we use sscanf on this buffer but we don't ensure that the string is terminated inside the buffer, this can lead to OOB read when using sscanf. Fix this issue by using memdup_user_nul instead of memdup_user.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Fix slab-out-of-bounds in mlx5_query_nic_vport_mac_list mlx5_query_nic_vport_mac_list() sizes its firmware command buffer using the PF's log_max_current_uc/mc_list capabilities. When querying a VF vport with a larger configured max (via devlink), the firmware response can overflow this buffer: BUG: KASAN: slab-out-of-bounds in mlx5_query_nic_vport_mac_list+0x453/0x4c0 [mlx5_core] Read of size 4 at addr ff1100013ffc8a12 by task kworker/u96:2/385 CPU: 12 UID: 0 PID: 385 Comm: kworker/u96:2 Not tainted 7.0.0-rc6+ #1 PREEMPT Hardware name: QEMU Standard PC (Q35 + ICH9, 2009) Workqueue: mlx5_esw_wq esw_vport_change_handler [mlx5_core] Call Trace: <TASK> dump_stack_lvl+0x69/0xa0 print_report+0x176/0x4e4 kasan_report+0xc8/0x100 mlx5_query_nic_vport_mac_list+0x453/0x4c0 [mlx5_core] esw_update_vport_addr_list+0x2e3/0xda0 [mlx5_core] esw_vport_change_handle_locked+0xa1f/0x1060 [mlx5_core] esw_vport_change_handler+0x6a/0x90 [mlx5_core] process_one_work+0x87f/0x15e0 worker_thread+0x62b/0x1020 kthread+0x375/0x490 ret_from_fork+0x4dc/0x810 ret_from_fork_asm+0x11/0x20 </TASK> Fix by querying the vport's own HCA caps to size the buffer correctly. Refactor the function to allocate and return the MAC list internally, removing the caller's dependency on knowing the correct max.

In the Linux kernel, the following vulnerability has been resolved: tools/nolibc/stdlib: fix memory error in realloc() Pass user_p_len to memcpy() instead of heap->len to prevent realloc() from copying an extra sizeof(heap) bytes from beyond the allocated region.

In the Linux kernel, the following vulnerability has been resolved: ice: ensure the copied buf is NUL terminated Currently, we allocate a count-sized kernel buffer and copy count bytes from userspace to that buffer. Later, we use sscanf on this buffer but we don't ensure that the string is terminated inside the buffer, this can lead to OOB read when using sscanf. Fix this issue by using memdup_user_nul instead of memdup_user.

In the Linux kernel, the following vulnerability has been resolved: tpm_tis_spi: Account for SPI header when allocating TPM SPI xfer buffer The TPM SPI transfer mechanism uses MAX_SPI_FRAMESIZE for computing the maximum transfer length and the size of the transfer buffer. As such, it does not account for the 4 bytes of header that prepends the SPI data frame. This can result in out-of-bounds accesses and was confirmed with KASAN. Introduce SPI_HDRSIZE to account for the header and use to allocate the transfer buffer.

In the Linux kernel, the following vulnerability has been resolved: drm/vmwgfx: Fix invalid reads in fence signaled events Correctly set the length of the drm_event to the size of the structure that's actually used. The length of the drm_event was set to the parent structure instead of to the drm_vmw_event_fence which is supposed to be read. drm_read uses the length parameter to copy the event to the user space thus resuling in oob reads.

In the Linux kernel, the following vulnerability has been resolved: net: fix out-of-bounds access in ops_init net_alloc_generic is called by net_alloc, which is called without any locking. It reads max_gen_ptrs, which is changed under pernet_ops_rwsem. It is read twice, first to allocate an array, then to set s.len, which is later used to limit the bounds of the array access. It is possible that the array is allocated and another thread is registering a new pernet ops, increments max_gen_ptrs, which is then used to set s.len with a larger than allocated length for the variable array. Fix it by reading max_gen_ptrs only once in net_alloc_generic. If max_gen_ptrs is later incremented, it will be caught in net_assign_generic.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: SCO: Fix not validating setsockopt user input syzbot reported sco_sock_setsockopt() is copying data without checking user input length. BUG: KASAN: slab-out-of-bounds in copy_from_sockptr_offset include/linux/sockptr.h:49 [inline] BUG: KASAN: slab-out-of-bounds in copy_from_sockptr include/linux/sockptr.h:55 [inline] BUG: KASAN: slab-out-of-bounds in sco_sock_setsockopt+0xc0b/0xf90 net/bluetooth/sco.c:893 Read of size 4 at addr ffff88805f7b15a3 by task syz-executor.5/12578

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: check A-MSDU format more carefully If it looks like there's another subframe in the A-MSDU but the header isn't fully there, we can end up reading data out of bounds, only to discard later. Make this a bit more careful and check if the subframe header can even be present.

In the Linux kernel, the following vulnerability has been resolved: regmap: maple: Fix cache corruption in regcache_maple_drop() When keeping the upper end of a cache block entry, the entry[] array must be indexed by the offset from the base register of the block, i.e. max - mas.index. The code was indexing entry[] by only the register address, leading to an out-of-bounds access that copied some part of the kernel memory over the cache contents. This bug was not detected by the regmap KUnit test because it only tests with a block of registers starting at 0, so mas.index == 0.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: RFCOMM: Fix not validating setsockopt user input syzbot reported rfcomm_sock_setsockopt_old() is copying data without checking user input length. BUG: KASAN: slab-out-of-bounds in copy_from_sockptr_offset include/linux/sockptr.h:49 [inline] BUG: KASAN: slab-out-of-bounds in copy_from_sockptr include/linux/sockptr.h:55 [inline] BUG: KASAN: slab-out-of-bounds in rfcomm_sock_setsockopt_old net/bluetooth/rfcomm/sock.c:632 [inline] BUG: KASAN: slab-out-of-bounds in rfcomm_sock_setsockopt+0x893/0xa70 net/bluetooth/rfcomm/sock.c:673 Read of size 4 at addr ffff8880209a8bc3 by task syz-executor632/5064

In the Linux kernel, the following vulnerability has been resolved: dma-mapping: benchmark: fix node id validation While validating node ids in map_benchmark_ioctl(), node_possible() may be provided with invalid argument outside of [0,MAX_NUMNODES-1] range leading to: BUG: KASAN: wild-memory-access in map_benchmark_ioctl (kernel/dma/map_benchmark.c:214) Read of size 8 at addr 1fffffff8ccb6398 by task dma_map_benchma/971 CPU: 7 PID: 971 Comm: dma_map_benchma Not tainted 6.9.0-rc6 #37 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:117) kasan_report (mm/kasan/report.c:603) kasan_check_range (mm/kasan/generic.c:189) variable_test_bit (arch/x86/include/asm/bitops.h:227) [inline] arch_test_bit (arch/x86/include/asm/bitops.h:239) [inline] _test_bit at (include/asm-generic/bitops/instrumented-non-atomic.h:142) [inline] node_state (include/linux/nodemask.h:423) [inline] map_benchmark_ioctl (kernel/dma/map_benchmark.c:214) full_proxy_unlocked_ioctl (fs/debugfs/file.c:333) __x64_sys_ioctl (fs/ioctl.c:890) do_syscall_64 (arch/x86/entry/common.c:83) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) Compare node ids with sane bounds first. NUMA_NO_NODE is considered a special valid case meaning that benchmarking kthreads won't be bound to a cpuset of a given node. Found by Linux Verification Center (linuxtesting.org).

In the Linux kernel, the following vulnerability has been resolved: ksmbd: validate mech token in session setup If client send invalid mech token in session setup request, ksmbd validate and make the error if it is invalid.

In the Linux kernel, the following vulnerability has been resolved: i2c: i801: Fix block process call transactions According to the Intel datasheets, software must reset the block buffer index twice for block process call transactions: once before writing the outgoing data to the buffer, and once again before reading the incoming data from the buffer. The driver is currently missing the second reset, causing the wrong portion of the block buffer to be read.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix potencial out-of-bounds when buffer offset is invalid I found potencial out-of-bounds when buffer offset fields of a few requests is invalid. This patch set the minimum value of buffer offset field to ->Buffer offset to validate buffer length.

In the Linux kernel, the following vulnerability has been resolved: tunnels: fix out of bounds access when building IPv6 PMTU error If the ICMPv6 error is built from a non-linear skb we get the following splat, BUG: KASAN: slab-out-of-bounds in do_csum+0x220/0x240 Read of size 4 at addr ffff88811d402c80 by task netperf/820 CPU: 0 PID: 820 Comm: netperf Not tainted 6.8.0-rc1+ #543 ... kasan_report+0xd8/0x110 do_csum+0x220/0x240 csum_partial+0xc/0x20 skb_tunnel_check_pmtu+0xeb9/0x3280 vxlan_xmit_one+0x14c2/0x4080 vxlan_xmit+0xf61/0x5c00 dev_hard_start_xmit+0xfb/0x510 __dev_queue_xmit+0x7cd/0x32a0 br_dev_queue_push_xmit+0x39d/0x6a0 Use skb_checksum instead of csum_partial who cannot deal with non-linear SKBs.